Sharp FP-N25CX Manuel utilisateur

Marque: Sharp

Modèle: FP-N25CX

Catégorie: Purificateurs d'air

Taper: Manuel utilisateur

Ce manuel convient également à

Plasmacluster FP-N25CX

ENGLISH

FP-N25CX

AIR PURIFIER

OPERATION MANUAL

PURIFICATEUR D’AIR

MANUEL D’UTILISATION

ENGLISH

FRANÇAIS

Free Standing

Type mobile

*Plasmacluster is a trademark of

Sharp Corporation.

*Plasmacluster est une marque de

commerce de Sharp Corporation.

Please read before operating your new Air Purifier

The air purifier draws in room air from its air intake, lets the air pass through a

Active Carbon Filter (deodorization filter) and a True HEPA Filter (dust collec-

tion filter) inside of the unit, then discharges the air from its air outlet. The air

purifier unit repeats this process by moving its internal fan.

As air passes through, the True HEPA Filter can remove 99.97% of dust par-

ticles, of as small as 0.3 microns. The Active Carbon Filter gradually absorbs

odor elements as they repeatedly pass through the filter. (Odor elements are

absorbed by True HEPA Filter as well.)

Some odor ingredients absorbed by the filters may become separated and

may be discharged through the air outlet and result in additional odor. De-

pending on the usage environment, especially when the product is used in a

condition significantly more severe than household use, this odor may be-

come strong in a shorter period than expected. In this case, clean the Active

Carbon Filter (Refer to E-14)

If the odor persists, then the filters are fully expended and it is necessary to

purchase the optional replacement filter kit FZ-N25HFU.

ENGLISH

FEATURES

Plasmacluster Ion Control

Your new air purifier will control the

ratio of negative ions and positive ions

depending on the condition of the

room.

• Clean Mode

Approximately the same numbers of

positive and negative ions are dis-

charged.

• Ion Control Mode

Plenty of negative ions exist in natu-

ral surroundings such as waterfalls or

forests. In this mode, negative ions

will be released in an increased rate.

• AUTO Plasmacluster Ion Mode

The unit will switch between Clean

Mode and Ion Control Mode automati-

cally depending on the amount of im-

purities in the air detected by the odor

sensor.

• Filters

1) Active Carbon Filter

Absorbs odor elements.

2) True HEPA (High Efficiency

Particulate Air) Filter with

anti-bacterial filter

High-efficiency particle collection

including pollen and dust.

CONTENTS

• FOR CUSTOMER ASSISTANCE (U.S.) ......E-2

• CONSUMER LIMITED WARRANTY (U.S.) .E-3

•

FOR CUSTOMER ASSISTANCE (CANADA) .

E-4

• LIMITED WARRANTY (CANADA) ...............E-5

IMPORTANT SAFETY INSTRUCTIONS....

E-6

•WARNING....................................................E-6

• CAUTIONS CONCERNING OPERATION ...E-7

• REMOTE CONTROL LIMITATIONS ............E-7

• INSTALLATION GUIDELINES .....................E-7

• FILTER GUIDELINES ..................................E-7

PART NAMES.......................................... E-8

• MAIN UNIT DISPLAY ...................................E-8

• BACK ...........................................................E-8

• INCLUDED...................................................E-8

PREPARATION........................................E-9

• INSERTING BATTERIES

IN THE REMOTE CONTROL ......................E-9

• FILTER INSTALLATION............................ E-10

OPERATION .......................................... E-12

• MAIN UNIT OPERATION.......................... E-12

• REMOTE CONTROL USE........................ E-13

• REMOTE CONTROL OPERATION .......... E-14

CARE AND MAINTENANCE.................E-15

• MAIN UNIT................................................ E-15

• ODOR SENSOR ....................................... E-15

• FILTER CLEANING................................... E-15

• FILTER REPLACEMENT

GUIDELINES ............................................ E-16

TROUBLE SHOOTING.......................... E-17

SPECIFICATIONS ................................. E-18

E-1

ENGLISH

Thank you for purchasing the SHARP FP-N25CX. Please read this manual carefully for the correct

usage information. Before using this product, be sure to read the section: “Important Safety In-

structions.”

After reading this manual, retain it in a convenient location for future reference.

E-2

FOR CUSTOMER ASSISTANCE

(the United States)

To aid in answering questions if you call for service or for reporting loss or theft, please

record below the model and serial number located on the back side of the unit.

MODEL NUMBER

SERIAL NUMBER

DATE OF PURCHASE

Dealer Name

Address

City

State

Zip

Telephone

TO PHONE: Dial 1-800-BE-SHARP (237-4277) for:

SERVICE (for your nearest Sharp Authorized Servicer)

PARTS (for your Authorized Parts Distributor)

ACCESSORIES

ADDITIONAL CUSTOMER INFORMATION

TO WRITE: For service problems, warranty information, missing items and other assistance:

Sharp Electronics Corporation

Customer Assistance Center

1300 Naperville Drive

Romeoville, IL 60446-1091

TO ACCESS THE INTERNET: www.sharpusa.com

Please provide the following information when you write or call: model number, serial number,

date of purchase, your complete mailing address (including zip code), your daytime telephone

number (including area code) and description of the problem.

ENGLISH

CONSUMER LIMITED WARRANTY

CONSUMER LIMITED WARRANTY FOR THE UNITED STATES

SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the

“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that

it will, at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured

equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.

This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below

nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or

other misuse, abnormal service or handling, or which has been altered or modified in design or construction.

In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide

proof of purchase to the servicer.

The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law.

ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE

LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limita-

tions on how long an implied warranty lasts, so the above limitation may not apply to you.

Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those

described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.

The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and

exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described

herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the

Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or other-

wise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were

caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable

or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow the

exclusion of incidental or consequential damages, so the above exclusion may not apply to you.

THIS WARRANTY GIVES YOU SPECIFlC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY

FROM STATE TO STATE.

Your Product Model Number & Description:

Warranty Period for this Product:

Additional Item(s) Excluded From Warranty

Coverage (If any):

Where to Obtain Service:

What to Do to Obtain Service:

FP-N25CX Air Purifier. Be sure to have this information available when

you need service for your Product.

One (1) year parts and labor from date of purchase.

Appearance items of the Product, filters, or accessories, or any printed

materials.

From a Sharp Authorized Servicer located in the United States. To find

the location of the nearest Sharp Authorized Servicer, call Sharp Toll

Free at 1-800-BE-SHARP.

Ship prepaid or carry in your Product to a Sharp Authorized Servicer.

Be sure to have Proof of Purchase available. If you ship the Product,

be sure it is insured and packaged securely.

TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP, OR VISIT OUR WEBSITE AT

www.sharpusa.com

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430-2135

E-3

FOR CUSTOMER ASSISTANCE

(Canada)

To aid in answering questions if you call for service or for reporting loss or theft, please

record below the model and serial number located on the back side of the unit.

MODEL NUMBER

SERIAL NUMBER

DATE OF PURCHASE

Dealer Name

Address

City

Province

Postal Code

Telephone

TO PHONE: Dial 1-905-568-7140 for:

SERVICE (for your nearest Sharp Authorized Servicer)

PARTS (for your Authorized Parts Distributor)

ACCESSORIES

ADDITIONAL CUSTOMER INFORMATION

TO WRITE: For service problems, warranty information, missing items and other assistance:

Sharp Electronics of Canada Ltd.

Customer Care

335 Britannia Road East

Mississauga, Ontario L4Z 1W9

TO ACCESS THE INTERNET: www.sharp.ca

Please provide the following information when you write or call: model number, serial number,

date of purchase, your complete mailing address (including Postal Code), your daytime tel-

ephone number (including area code) and description of the problem.

E-4

ENGLISH

E-5

LIMITED WARRANTY

Consumer Electronics Products

Congratulations on your purchase!

Sharp Electronics of Canada Ltd. (hereinafter called “Sharp”) gives the following express warranty to the first con-

sumer purchaser for this Sharp brand product, when shipped in its original container and sold or distributed in Canada

by Sharp or by an Authorized Sharp Dealer:

Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and work-

manship. If any such defects should be found in this product within the applicable warranty period, Sharp shall, at its

option, repair or replace the product as specified herein.

This warranty shall not apply to:

(a) Any defects caused or repairs required as a result of abusive operation, negligence, accident, improper installa-

tion or inappropriate use as outlined in the owner’s manual.

(b) Any Sharp product tampered with modified, adjusted or repaired by any party other than Sharp, Sharp’s Author-

ized Service Centres or Sharp’s Authorized Servicing Dealers.

but not limited to head cleaning tapes and chemical cleaning agents.

(d) Any replacement of accessories, glassware, consumable or peripheral items required through normal use of the

product including but not limited to earphones, remote controls, AC adapters, batteries, temperature probe, stylus,

trays, filters, belts, ribbons, cables and paper.

(e) Any cosmetic damage to the surface or exterior that has been defaced or caused by normal wear and tear.

(f) Any damage caused by external or environmental conditions, including but not limited to transmission line/power

line voltage or liquid spillage.

(g) Any product received without appropriate model, serial number and CSA/cUL markings.

(h) Any products used for rental or commercial purposes.

(i) Any installation, setup and/or programming charges.

Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery

of the Sharp product together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Author-

ized Sharp Service Centre or an Authorized Sharp Servicing Dealer. In home warranty service may be provided at

Sharp’s discretion on any Sharp television with the screen size of 27” or larger and on any Sharp Over-the-Range

Microwave Oven.

This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their

agent or employee is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law

permits, Sharp disclaims any and all liability for direct or indirect damages or losses or for any incidental, special or

consequential damages or loss of profits resulting from a defect in material or workmanship relating to the product,

including damages for the loss of time or use of this Sharp product or the loss of information. The purchaser will be

responsible for any removal, reinstallation, transportation and insurance costs incurred. Correction of defects, in the

manner and period of time described herein, constitute complete fulfillment of all obligations and responsibilities of

Sharp to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether based on

contract, negligence, strict liability or otherwise.

WARRANTY PERIODS: Parts & Labour (exceptions noted)

Audio Products 1 year

Camcorder 1 year

DVD Products 1 year

LCD Projector 1 year (lamp 90 days)

LCD TV 1 year

Microwave Oven 2 years (magnetron component-3 additional years)

Television Products 1 year (picture tube component-1 additional year)

VCR Products 1 year

Vacuum Cleaner 1 year

Air Purifier 1 year (except filters)

To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:

SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East Mississauga, Ontario L4Z 1W9

For more information on this Warranty, Sharp Canada Products,

Accessory Sales, Dealer or Service Locations, please call (905)

568-7140

Visit our Web site: www.sharp.ca

SERVICE

(VALID IN CANADA ONLY)

IMPORTANT SAFETY INSTRUCTIONS

E-6

When using electrical appliances, basic safety precautions should be followed, including the

following:

WARNING - To reduce the risk of electrical shock, fire or injury to persons:

• Read all instructions before using the air purifier.

• Use only a 120-volt outlet with a polarized receptacle.

• The air purifier has a polarized plug (one blade is wider than the other is). This plug will fit in a

polarized outlet only one way. Initially, if the plug does not fit into the outlet, reverse it. If it still does not

fit, contact a qualified electrician or service person.

• Do not use the air purifier if the power cord or plug is damaged or the connection to the wall

outlet is loose.

• Periodically remove dust from the power plug.

• Do not insert fingers or foreign objects into the intake or air outlet.

When removing the power plug, always hold the plug and never pull the cord.

Electrical shock and/or fire from short circuit may occur as result.

• Do not use this air purifier near gas appliances or fireplaces.

• Remove the power plug from the wall outlet before cleaning the unit and when not using the

unit.

Electrical shock from bad insulation and / or fire from short circuit may occur as a result.

• If the power cord is damaged, it must be replaced by the manufacturer, its service agent,

Sharp authorized service or similarly qualified person in order to avoid a hazard.

• Do not operate when using aerosol insecticides or in rooms where there is oily residue, incense,

sparks from lit cigarettes, chemical fumes in the air or a humidity condition.

• Use care when cleaning the air purifier. Strong corrosive cleansers may damage the exterior.

• Only Sharp Authorized Servicers should service this air purifier. Contact the nearest Servicer for any

problems, adjustments, or repairs.

• The batteries must be removed from the remote control before disposal, and the batteries must be

disposed of safely.

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-

ant to 15 of the FCC and Industry Canada ICES-003 Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment gener-

ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be deter-

mined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-

nected.

• Consult the dealer or an experienced radio/TV technician for help.

ENGLISH

CAUTIONS CONCERNING OPERATION

• Do not block the intake and air outlet.

• Do not use the unit near or on hot objects, such as range or where it may come into contact with

steam.

• Do not use the unit on its side.

• Always hold the handle on the back of the unit when moving it.

• Holding the front panel when carrying may cause it to detach, thus dropping the unit and resulting in

bodily injury.

• Do not operate the unit without the filter.

• Do not wash and reuse HEPA filter and Active Carbon Filter.

• Clean outside with a damp cloth only.

The unit surface may become damaged or cracked.

In addition, the sensor may malfunction as a result.

REMOTE CONTROL LIMITATIONS

DO NOT USE THE REMOTE CONTROL IN THE FOLLOWING LOCATIONS:

• Any location where there is inverter lighting equipment or electronic spontaneous lighting

equipment

The remote control may become inoperative. In this case, move away from such lighting equipment

or change direction.

• Location exposed to direct sunlight

The unit may not receive signals from the remote control.

The unit may not respond to the signals of the remote control if there is a problem with the fluorescent

lighting.

INSTALLATION GUIDELINES

• Leave at least 7 feet (2m) of space from equipments which involve radio wave such as televi-

sions, radios or wave clocks.

Electrical interference may occur.

• Leave at least 2 feet (60cm) of space from the wall.

The motor may overheat, causing a malfunction.

•Avoid a location where the sensor is exposed to direct wind.

The unit may not operate properly.

•Avoid a location where curtains, etc., come into contact with the intake or air outlet.

Curtains, etc., may become dirty or a malfunction may occur.

• The wall behind the air outlet may become dirty as time passes. When using the unit for extensive

period in the same location, use a vinyl sheet, etc., to prevent the wall from becoming dirty. In addi-

tion, periodically clean the wall, etc.

• Place on a stable surface with sufficient air circulation.

FILTER GUIDELINES

• Follow the instructions in this manual for correct care and maintenance of the filters.

E-7

IMPORTANT SAFETY INSTRUCTIONS

PART NAMES

MAIN UNIT DISPLAY

AUTO Operation Indicator Light

Quick AUTO operation Indicator Light

Pollen Mode Indicator Light

OFF Timer Display Indicator Lights

(set using remote control)

Odor Sensor

Remote Control Receiver

CLEAN-SIGN Light

MODE-ON/OFF Button See Page E-12

Main Unit

True HEPA Filter (blue) See Page E-16

Active Carbon Filter (black)

See Page E-16

Filter Support

Front Panel

Remote Control

See Page E-14

Handle

Air Outlet

Power Cord

Power Plug

E-8

Fan Speed Indicator Lights

Plasmacluster Indicator Light

BACK

INCLUDED

Remote Control

(1 unit)

Battery

(AA battery X 2 )

• Operation manual

AUTO SILENT LOW HIGH

POLLEN

CLEAN SIGN OFF TIMER h

QUICK AUTO

Plasmacluster

ENGLISH

E-9

Battery Information

• The batteries for this remote control are for initial use only . Change the batteries when

necessary.

• Incorrect usage of the batteries may cause battery fluid leakage and/or damage.

Take care of the following when handling:

•When replacing the batteries, replace both batteries with new ones of the same type.

(Use 2 AA manganese batteries.)

•When not using the unit or remote control for an extended period, remove the batteries.

• The batteries are for initial use only and may be depleted within 1 year.

INSERTING BATTERIES IN THE REMOTE CONTROL

Remove the back cover

Press and slide the back cover to remove.

Insert batteries

Insert batteries with and as shown below.

Close the back cover

PREPARATION

Be sure to remove the filters from the plastic bags before using the unit.

Filter Removal

Place the unit facing up and

remove the Front Panel.

Lift both sides of the bottom of the Front

Panel to remove the Front Panel.

Remove Active Carbon Filter

(black) and True HEPA Filter

(blue) from the plastic bags.

E-10

Be sure to remove the power plug from the wall outlet.

FILTER INSTALLATION

Remove the Filter Support.

Pinch the two tabs and lift to remove.

Tabs

Front Panel

Filter Support

Tabs (2 places)

Active Carbon Filter

True HEPA Filter

ENGLISH

Tab

E-11

outlet.

Filter Installation

After the True HEPA Filter

is removed from the plas-

tic bag, place it in the main

unit with the tabs facing

up.

Do not install the filter backwards

or the unit will not operate prop-

erly.

After removing the Active

Carbon Filter from the plas-

tic bag, place it on top of

the True HEPA Filter.

Make sure that the tab of

the True HEPA Filter re-

mains visible.

Insert the upside tabs of

the Filter Support into the

associated holes of the

main unit.

Next push the bottom side

tabs into the main unit.

Fill in the usage start date

on the Date Label, which

can be found on back side

of Front Panel.

Use the date as a guide for the Fil-

ter Replacement schedule.

PREPARATION

True HEPA Filter

Active Carbon Filter

Holes in the

main unit

Tabs of the up side

Filter Support

Date Label

Tabs of the

bottom side

Tab of the True HEPA Filter

OPERATION

MAIN UNIT OPERATION

DETERMINING THE BASE IMPURITY RATE

For the first 2 minutes after the power plug is inserted into the wall outlet, the unit will

check the conditions of the air. If operation is set to ON during this time, the CLEAN-

SIGN LIGHT will alternately flash in green, orange and red.

The unit will start operating when the MODE-ON/OFF Button is pressed.

To change operating modes, press the MODE-ON/OFF Button until the desired control

is activated.

Plasmacluster Indicator Light

Main Unit Controls

E-12

MODE-ON/OFF Button

• AUTO

• SILENT

•LOW

• HIGH

• QUICK AUTO

• POLLEN

AUTO operation

The fan speed is automati-

cally switched (HIGH, LOW,

SILENT) depending on the

amount of odor in the air. The

sensor detects the odor for

efficient air purification.

SILENT operation

The unit will operate quietly

using minimal air intake.

Stop

POLLEN mode operation

The unit will operate at High fan

speed for 10 minutes, then will al-

ternate between LOW and HIGH.

10 minutes: High fan speed

20 minutes:

Low fan speed

20 minutes: High fan speed

QUICK AUTO operation

The unit will operate at High fan

speed for 10 minutes, then will

operate in AUTO operation.

LOW operation

Plasmacluster

AUTO SILENT LOW HIGH

POLLEN

CLEAN SIGN OFF TIMER h

QUICK AUTO

HIGH operation

10 minutes: High fan speed

AUTO operation

ENGLISH

PLASMACLUSTER INDICATOR LIGHT

Plasmacluster ion operation is selected using the remote control.

Blue light

When the Plasmacluster ion operation is in Clean Mode, or in AUTO Plasmacluster Ion Mode

and the air in the room is impure, the light will activate and the unit will operate in Clean Mode.

Green light

When the Plasmacluster ion operation is in the Ion Control Mode, or in AUTO Plasmacluster

Ion Mode and the air in the room is clean, this light will activate and the unit will operate in Ion

Control Mode.

Light off

There are no Plasmacluster ions being generated.

E-13

CLEAN-SIGN LIGHT

The color changes according to the air condition.

Clean (Green) Slightly Impure (Orange) Very Impure (Red)

ABOUT THE CLEAN-SIGN

• The condition of the CLEAN-SIGN depends on the Odor Sensor’s reading of the room environ-

ment when the plug is inserted into the wall outlet.

• It is possible to have a green CLEAN-SIGN with impurities in the air if the air purifier was just

introduced to the room environment. After a while, however, the base impurity rate will be

adjusted to read room environment correctly.

REMOTE CONTROL USE

• Operate with the remote control facing the main unit

receiver.

• The signal range is about 23 feet (7m).

•Make sure there are no objects blocking the path of

the signal.

•A beep sound will be heard from the main unit when a

signal is received.

NOTE

•Avoid dropping or damaging the remote control, using

in a high humidity condition, in direct sunlight or near a

heat source.

Receiver

Transmitter

OPERATION

Plasmacluster

AUTO

MANUAL

Fan Control

POLLEN

OFF

TIMER

QUICK AUTO

POWER ON/OFF

CLEAN

ION CONTROL

OFF

AUTO

Plasmacluster Ion mode Selections

Auto

When pressed, the unit will switch between

Clean Mode and the Ion Control Mode auto-

matically depending on the amount of impuri-

ties in the air as detected by the odor sensor.

Clean Mode will operate for 1 minute when

the Auto function is selected.

Ion Control

When pressed, the unit will constantly oper-

ate in Ion Control Mode.

The Plasmacluster Ion Indicator Light is green.

Clean

When pressed, the unit will con-

stantly operate in the Clean Mode,

in which the same numbers of posi-

tive and negative ions are dis-

charged. The Plasmacluster Indica-

tor Light is blue.

Off

The generation of ions will cease

and the Plasmacluster Indicator

Light will go out.

E-14

REMOTE CONTROL OPERATION

OPERATION

Operations available with

the Remote Control

• AUTO

• MANUAL

• POLLEN

• OFF TIMER

• QUICK AUTO

Plasmacluster Ion mode

selections

• AUTO

• CLEAN

• ION CONTROL

• OFF

•When you press the POWER ON/OFF Button, a short

beep will sound and operation will start in AUTO Mode.

Transmitter

Pollen Mode Operation

Button

See Page E-12

Off Timer Button

The set time switches every time

the button is pressed as shown

below.

1 hour 4 hours

Cancel 8 hours

• The indicator light shows the

remaining time.

POWER ON/OFF Button

To stop, press the POWER

ON/OFF Button again.

A long beep will sound and

operation will stop.

Auto (Fan Speed) Button

The fan speed switches au-

tomatically depending on the

amount of impurities in the air.

Manual (Fan Speed) Button

The fan speed can be

switched among Silent, Low,

and High settings.

Quick Auto Button

The operation mode is effec-

tive when quick removal of

impurities in the air is de-

sired.

Note: By manually selecting ei-

ther Ion Control or Clean

Mode, this will lock the unit

into the selected mode and

will not change to the other

even if room condition

changes.

ENGLISH

FILTER CLEANING

Clean the top surface of the Filter Support and Active

Carbon Filter lightly with a vacuum cleaner without re-

moving from the main unit.

NOTE

• The Active Carbon Filter is damaged easily. Do not

force the nozzle of a vacuum cleaner against the Ac-

tive Carbon Filter or wash it with water. The True HEPA

Filter should never be washed or cleaned.

Filter Support

CARE AND MAINTENANCE

To maintain optimum performance of this air purifier, please clean the unit including

the sensor and filters periodically.

When cleaning the unit, be sure to unplug the power cord, and never handle the plug

with wet hands. Electrical shock and/or bodily injury may occur as a result.

MAIN UNIT

To prevent dirt or stains on the main unit, clean as often as necessary. If stains are allowed to

remain, they may become difficult to remove.

Wipe with a dry, soft cloth

For stubborn stains or dirt, use a soft cloth dampened with warm water.

Do not use volatile fluids

Benzene, paint thinner, polishing powder, etc., may damage the surface.

Do not use detergents

Detergent ingredients may damage the unit.

Keep the unit away from water

ODOR SENSOR

The sensitivity of the sensor will become

unstable if the odor sensor is dirty or

blocked. Remove dust from the surfaces

of the sensor openings using a vacuum

cleaner.

Odor Sensor

E-15

FILTER REPLACEMENT GUIDELINES

The replacement period differs depending on the room environment, the

usage hours and location of Air Purifier.

If dust or odor persists, replace the filters.

Guide for filter replacement timing

•The following filter life and replacement period is based on the condition of smoking

10 cigarettes per day, reducing the dust collection/deodorization power to half com-

pared with that of new filters.

We recommend replacing the filters more frequently if the product is used in a condi-

tion significantly more severe than normal household use.

•True HEPA Filter About 2 years after opening

•Active Carbon Filter About 2 years after opening

REPLACING THE FILTERS

See page E-10,11 for directions on how to install the filters when

replacing.

Fill in the usage start date of the filters on the Date Label, which

can be found on the back side of the Front Panel.

Replacement Filters

•True HEPA Filter: 1 unit

•Active Carbon Filter: 1 unit

Model: FZ-N25HFU

In case you need either a True HEPA Filter or an Active Carbon Filter only:

•True HEPA Filter: PFIL-A071KKEZ

•Active Carbon Filter: PFIL-A052KKEZ

For replacement filters contact Sharp for information

(U.S.A.) 1-800-BE-SHARP or website at www.sharpusa.com

(Canada) (905)568-7140 or website at www.sharp.ca

Disposal of Filters

Please dispose of replaced filters according to the local disposal laws and regulations.

True HEPA Filter materials:

• Filter: Polypropylene

• Frame: Polyester

Active Carbon Filter Materials:

•Deodorizer: Activated charcoal

•Net: Polypropylene 60% Polyester 40%

E-16

CARE AND MAINTENANCE

ENGLISH

TROUBLESHOOTING

E-17

Before calling for repair, please review the list below, since the problem may not be a unit malfunction.

SYMPTOM

REMEDY (not a malfunction)

The Remote Control does not

work

• Have the batteries been depleted?

• Are the batteries inserted correctly?

• Is a fluorescent lighting in the room flickering due to serv-

ice life? (Refer to E-7,E-9)

Odors and smoke are not re-

moved

• Clean the filters if they appear to be heavily soiled.

(Refer to E-15)

• Check to see that the filters have been removed from

their original plastic bags.

The CLEAN-SIGN Light lights

green even when the air is im-

pure

• The air could be impure at the time the unit was plugged

in. (Refer to E-13)

The CLEAN-SIGN Light lights

orange or red even when the air

is clean

• The sensitivity of the sensor becomes unstable when

the opening of the odor sensor is dirty or is clogged.

Clean the dust around the sensor opening using a

vacuum cleaner. (Refer to E-15)

•When in Clean Mode ( or Ion Control Mode), the

Plasmacluster Indicator Light color will not change.

A clicking or ticking sound is

heard from the unit

• Clicking sound is emitted when the unit is in the Ion Con-

trol Mode, and ticking sound is emitted when the unit is

generating ions.

If the sound is irritating, set the unit away from you.

This is normal and not a malfunction.

The discharged air has an

aroma or odor.

• Check to see if the filters are heavily soiled.

Check the Active Carbon Filter or replace the filters.

• Plasmacluster Air Purifiers emit small traces of ozone

which may produce an odor. These ozone emissions are

below safety levels set by the FDA.

The Plasmacluster Indicator

Light remains green (or blue)

and does not change

The unit does not operate when

cigarette smoke is in the air.

• Is the unit installed in a location that is difficult for the

sensor to detect cigarette smoke?

• Are the odor sensor openings blocked or clogged?

(In this case, clean the openings.) (Refer to E-15)

SPECIFICATIONS

E-18

Model

Power supply

Fan Speed Adjustment

Rated Power

Fan Speed CFM (m

/min.)

Applicable Floor Surface

CADR

(Dust/Smoke/Pollen)

Cord Length

Dimensions

Weight

Fan

Speed

Operation

120V / 60Hz

128 sq.ft.* (11.8m

)

96 / 83 / 94

8.3 ft (2.5m)

16-1/2 in.(W)x5-15/16 in.(D)x16-5/8 in(H)

420mm(W)x151mm(D)x422mm(H)

9.9 lbs (4.5kg)

HIGH

49 W

88 (2.5)

LOW

28 W

46 (1.3)

SILENT

22 W

25 (0.7)

* The applicable floor surface area is appropriate for operating the unit at maximum fan speed.

Standby Power

In order to operate the electrical circuits while the power plug is inserted in the wall outlet, this

product consumes about 1.5W of standby power.

For energy conservation, unplug the power cord when the unit is not in use.

FP-N25CX

La page est en cours de chargement...

Sharp FP-N25CX Manuel utilisateur

Marque: Sharp

Modèle: FP-N25CX

Catégorie: Purificateurs d'air

Taper: Manuel utilisateur

Ce manuel convient également à

Plasmacluster FP-N25CX

Télécharger le PDF

rapport

dans d''autres langues

English: Sharp FP-N25CX User manual

Sharp FP-N25CX Manuel utilisateur

Ce manuel convient également à

Sharp FP-N25CX Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents