Bosch SHX3AR72UC/28 Guide d'installation

en Installation Instructions

fr Notice d’installation

es Instrucciones de instalación

Customer Service:

1-800-944-2904

These instuctions are intended

for use by qualified installers only

2

3

Safety Definitions

This indicates that damage to the appliance or property may occur as a

result of non-compliance with this advisory.

NOTICE

This indicates that death or serious injuries may occur as a result

of non-observance of this warning.

WARNING

!

Note: This alerts you to important information and/or tips.

Table of Contents

Safety Instructions ........................................4

Avoiding General Hazards ..................................5

Tools & Materials .........................................6

Pre-Install Checklist .......................................9

Enclosure Requirements ..................................10

Attach Water Inlet and Drain Hose ...........................12

Electrial Connections .....................................14

Positioning the Dishwasher ................................17

Installation of Mounting Brackets ............................18

Water Inlet Connection ....................................21

Drain Connection ........................................23

Attaching the Toe Panel ...................................25

Customer Service ........................................26

This indicates that minor or moderate injuries may occur as a

result of non-observance of this warning.

CAUTION

!

4

Important Safety Instructions:

Please READ and SAVE this information

To avoid possible injury or property damage, OBSERVE ALL WARNINGS

AND CAUTIONS.

WARNING:

These instructions are intended for use by qualified installers only. The

dishwasher must be installed by a qualified service technician or installer.

• In addition to these instructions, the dishwasher shall be installed to

meet all electrical and plumbing codes and ordinances (both national

and local).

Read these installation instructions completely and follow them carefully.

They will save you time and eort and help to ensure safety and optimum

dishwasher performance.

IMPORTANT

• The dishwasher drain hose must be installed with a portion of it at least

33″ (84 cm) o the cabinet floor; otherwise the dishwasher may not

drain properly.

• This dishwasher is intended for indoor residential use only, and should

not be used in commercial food service establishments.

• This dishwasher is designed to be enclosed on the top and both sides

by cabinetry.

• NEW INSTALLATION - If the dishwasher is a new installation, ensure all

connections are properly made before the dishwasher is moved into

place.

• REPLACEMENT - If the dishwasher is replacing another dishwasher,

check the existing dishwasher connections for compatibility with the

new dishwasher, and replace parts as necessary.

• This appliance has been found to be in compliance with CAN/CSA-C22.2

No. 167/UL 749. It is the responsibility of the owner and the installer

to determine if additional requirements and standards apply in specific

installations.

• Not for outdoor use.

5

WARNING

Avoiding General Hazards

To reduce the risk of electric shock, fire, or injury to persons, the installer

must ensure that the dishwasher is completely enclosed at the time of

installation.

Do not use the dishwasher until it is completely installed. When opening the

door on an uninstalled dishwasher, carefully open the door while supporting

the rear of the unit. Failure to follow this warning can cause the dishwasher

to tip over and result in serious injury.

Before installing the supplied counter top mounting brackets, decide which

method will be used to secure the dishwasher into its opening. Once these

mounting brackets are installed on the dishwasher, removing them is dif-

ficult and will damage the mounting brackets and the dishwasher.

In some conditions, hydrogen gas can form in a hot water system that

has not been used for weeks. Hydrogen gas is explosive. Before filling a

dishwasher from a system that has been o for weeks, run the water from

a nearby faucet in a well ventilated area until there is no sound or evidence

of gas.

Removing any cover or pulling the dishwasher from the cabinet can expose

hot water connections, electrical power and sharp edges or points. Handle

with care.

Proposition 65 Warning:

This product may contain a chemical known to the State of California, which

can cause cancer or reproductive harm. Therefore, the packaging of your

product may bear the following label as required by California:

Inspect the Dishwasher

After unpacking the dishwasher and prior to installation, thoroughly inspect

the dishwasher for possible freight or cosmetic damage. Report any damage

immediately. Cosmetic defects must be reported within 30 days of installation.

NOTE: Do not discard any bags or items that come with the original package

until after the entire installation has been completed.

STATE OF CALIFORNIA PROPOSITION 65 WARNING:

WARNING

Cancer and Reprodutive Harm - www.P65Warnings.ca.gov

6

Elbow connection with 3/4” female hose threads on

one end and fits your water supply line (copper tubing,

compression fitting, or braided hose) on the other.

Hot Water Supply Line - Minimum 3/8″ O.D. copper

tubing or metal braided dishwasher supply line.

Only needed if house water supply line is not sucient.

Shut-o valve and fittings appropriate for hot water

supply line (copper tubing/compression fitting, or

braided hose).

Tools and Materials Needed



Needle Nose Pliers

Pliers

ø1/16 in

(2 mm)

Adjustable Wrench

(x2)

Tape

Measure

Drill

2½” Hole Saw

Flat Screwdriver

Level

Phillips Screwdriver

7

Materials supplied (All Models)

Screw Clamp (for drain hose)

X 5

Mounting Brackets

Mounting Bracket Screws Ø 4x13mm

D

E

F

B

A

C

G

H

Clamp (for drain hose)

Screws

Metal toe panel screws

Drain hose

X 2

Metal Toe Panel (used with E)

8

Materials Supplied

(Model Dependent; for fully integrated dishwashers only)

Installation Guide for Fully Integrated

Door Panel

9

IMPORTANT!

Before you begin, you must read the safety instructions.

PRE-INSTALL CHECKLIST

1. Unpack unit. Retain packing material until successful installation is

complete.

2. Remove all packing material from inside the dishwasher.

3. Inspect parts to ensure you have all the necessary materials.

4. Flush household hot water supply for at least two minutes.

5. Measure the enclosure area. Is the opening at least 34" (863.6 mm)

high and 24" (609.6 mm) wide?

6. Is the opening near enough to the sink for the water line and drain

hoses to access plumbing?

7. Will the unit be installed close enough to the sink so that drain hose

length does not exceed 92" (2336.8 mm) and so that a portion of the

drain hose is raised at least 33" (840 mm) above the floor?

8. Do the openings for electric cable, water line, and drain hose routing

through cabinet fit within the shaded area in Figure 3?

9. Are the openings sanded smooth if wood or covered by a protective

gasket if metal?

10. Is your water heater set at 120°F (49°C) and does water pressure

measure 15-145 psi (1-10 bar)?

11. If installing in a corner, will the dishwasher door clear cabinet hardware?

12. Determine mounting method based on dishwasher model and counter-

top type (see Figures 11-14).

13. Only use included hardware for install. If replacing dishwasher, dispose

of old hose and other equipment properly.

10

Enclosure Requirements

To Avoid Scalding or Electrical Shock Hazard!

Make sure the water supply and electrical supply are shut o

before installation or service.

To Avoid Electrical Shock/Fire Hazard!

Do not allow the electrical and supply lines to touch.

Note: This dishwasher is designed to be enclosed on the top, back and

both sides by standard residential kitchen cabinetry.

• Select a location as close to the sink as possible for easy access to

water supply and drain lines.

• For proper dishwasher operation and appearance, ensure that the

enclosure is square and has the dimensions shown.

• If the dishwasher is to be installed in a corner, ensure that there is

adequate clearance to open the door as shown.

min 34"

(864 mm)

min 24"

(610 mm)

23

5/8

" - 24

1/4

"

(600 - 616 mm)

1











2

WARNING

!

11

Attach 90° elbow joint to dishwasher

oriented as shown. Do not over-

tighten.

• After locating the proper place for your dishwasher, create required

openings in your cabinets in order to allow for water, drain and

electrical lines on the appropriate side.

• The holes should be cut within the 7 x 2.5" area shown.

• If the opening is made through wood, sand it smooth.

• If the opening is made through metal, use the Edge Protector with

Power Cord clips Kit SMZEPCC1UC.

7"

(177.8 mm)

3

12

• Carefully flip the unit over. Remove the toe panel from the front of the

unit and retain for attachment to the front at a later time. Loosen the leg

levelers slightly.

Attaching Water Inlet and Drain Hose

• Attach elbow joint to dishwasher as shown. Do not overtighten.

• Attach hot water line to elbow. Use two wrenches to tighten to avoid

putting stress on the water inlet valve.

Avoid cross-threading! It will cause leaks. After attaching hose, temporarily

hook up the water supply then turn on water to check for leaks.

NOTICE

4

5

13

• Flip unit back upright, making sure the waterline is not pinched.

• Orient the drain hose toward direction of sink.

IMPORTANT: Route hose toward sink PRIOR TO connection. Do not turn

after attachment. Attach drain hose elbow (Part G) to back of unit using pli-

ers to install the spring clamp (Part B).

B

G

B

G

• Pre-level unit before positioning under counter by turning feet clockwise

to raise or counter-clockwise to lower. Maximum height the unit can be

raised with feet fully extended is 34.5" (876.3 mm).

• Position unit under counter to verify that it is level. If adjustment is needed,

remove unit from under counter and adjust as necessary.

• Once the unit is at a satisfactory height, insert leg leveler locking screw

(Part D) in back foot. Step 10 will complete the leveling process.

D

6

7

14

Electrical Connection

Avoid Electrical Shock Hazard!

Do not work on an energized circuit. Doing so could result in

serious injury or death. Only qualified electricians should perform

electrical work. Do not attempt any work on the dishwasher

electric supply circuit until you are certain the circuit is de-

energized.

To avoid possible injury or property damage, care should be exer-

cised when the dishwasher is installed or removed to reduce the

likelihood of damage to the power cord.

Avoid Fire Hazard!

Make sure electrical work is properly installed and checked by

qualified electricians.

Make sure there are no loose electrical connections. Make sure

all electrical connections are properly made.

Loose and improperly installed electrical connections can

result in overheating!

To avoid risk of fire, observe the following precautions:

Wall Socket Connections:

Only use the provided power cord for wall socket connections.

DO NOT attach an extension cord or any type of modified cord or

adapter with this appliance.

DO NOT cut or splice the power cord.

DO NOT alter the power cord in any way.

Permanent Wire Connections (in addition to the warnings above):

Only use the junction box power cord, sold as Accessory kit

#SMZPCJB1UC.

Carefully review the terminal block installation instructions.

DO NOT remove, alter or bypass the terminal block.

WARNING

!

15

Dishwasher Electrical Rating

Volts Hertz Amperes Watts

120 60 12 1,440

(max)

Electrical Supply

The customer has the responsibility of ensuring that the dishwasher electri-

cal installation is in compliance with all national and local electrical codes

and ordinances. The dishwasher is designed for an electrical supply of

120V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded

electrical circuit with a fuse or breaker rated for 15 or 20 amps.

Grounding Instructions

The dishwasher must be properly grounded before operating. This appli-

ance must be connected to a grounded metal permanent wiring system

or an equipment grounding conductor must be run with the circuit con-

ductors and connected to the equipment grounding terminal or lead on

the dishwasher.

Do NOT use an extension cord.

Make sure that the dishwasher is connected to a suitable ground in

compliance with all local codes or, in the absence of a local code, with

the NATIONAL ELECTRICAL CODE in the United States or the CANADIAN

ELECTRIC CODE C22.1-latest edition in Canada as well as any provincial/

state or municipal or local codes that apply.

Note: Installations requiring hard wiring and terminal block - The

accessory terminal block/junction box model, SMZPCJB1UC, designed

for permanent wire connection, is not included but can be ordered

through Customer Service by calling 1-800-944-2904. Follow the

instructions included with the kit.

16

8

• Plug the end of the supply cord securely into the back of the

dishwasher, looping it through the hooks on the base.

• The outlet for the power supply cord should be located in a cabinet

or wall adjacent to the dishwasher cabinet. Do not plug dishwasher in

until all the steps of installation are complete.

Note: Only use the included power cord. If cord is missing order kit

SMZPC002UC through Customer Service.

Note: If clips are required for the power cord use the Edge Protector with

Power Cord clips Kit SMZEPCC1UC.

17

• Orient the hoses and power cord so they go towards the sink and the

power outlet.

9

Positioning the Dishwasher

Do not leave coils of hoses or wires behind the dishwasher. Be sure to

pull the hoses all the way into the adjacent cabinet while pushing the

dishwasher in. Otherwise, the hoses can fold, kink or break, potentially

causing obstructions or leaks.

NOTICE

18

• Level the dishwasher horizontally by turning feet (1) clockwise to raise or

counter-clockwise to lower front of unit. Once level, (2) insert leg leveler

locking screws (Part D) and tighten.

(1)

(2)

D

10

19

Grasp mounting bracket (G) with pliers and fold bracket at the perforation

over onto itself as shown in 11a.

• Mount brackets on the top if your countertop is wood or other material

that can easily be drilled into. (see figure 11b)

• Mount brackets on the sides if your countertop is stone or any very hard

material that cannot be easily drilled into. (see figure 11b)

a

b

Installation of Mounting Brackets

Avoid Tip Over Hazard!

Do not use the dishwasher until it is completely installed.

When opening the door on an uninstalled dishwasher,

carefully open the door while supporting the rear of the unit.

Failure to follow this warning can result in serious injury.

WARNING

!

Note: Before installing the supplied counter top mounting brackets,

decide which method of securing the dishwasher into its enclosure will

be used.

Once the mounting brackets are installed on the dishwasher, removing

them is dicult and will damage the mounting brackets and the

dishwasher.

If you have a Fully Integrated Panel, do not attach mounting brackets until

after attaching the panel to the door.

11

20

• Attach mounting brackets to the frame with included screws (D).

Wood Countertop/

Top Mount

Stone Countertop/

Side Mount

12

La page est en cours de chargement...

Bosch SHX3AR72UC/28 Guide d'installation

Bosch SHX3AR72UC/28 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents