Cub Cadet 41CDC02G100 Le manuel du propriétaire

Catégorie
Coupe-herbe
Taper
Le manuel du propriétaire

Ce manuel convient également à

Operator’s Manual
2-Cycle Trimmer
Model CC 2000
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
P/N 769-00659 (2/03)
PRINTED IN USA
2
T
able of Contents
Content Page
Section 1: Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Section 2: Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Section 3: Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Section 4: Oil and Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Section 5: Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Section 6: Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Section 7: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Section 8: Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inside Back Cover
For more details about your unit, visit our website at www.cubcadet.com
NOTE: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S. Forest Land and the state of
California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by law that certain internal combustion engines operated
on forest brush and/or grass-covered areas be equipped with a spark arrestor, maintained in effective working order, or the engine be
constructed, equipped and maintained for the prevention of fire. Check with your state or local authorities for regulations pertaining to these
requirements. Failure to follow these requirements could subject you to liability or a fine. This unit is factory equipped with a spark arrestor. If
it requires replacement, Accessory Part #181696Spark Arrestor Screen is available by contacting the service department.
Finding the Model Number
Before you start assembling your new equipment, please locate the model plate on the equipment and copy the
information from it in the space provided below. This information is very important if you need help from our Customer
Support Department or an authorized dealer.
Calling Customer Support
If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of
this unit, please call the Customer Support Department.
Call 1-877-282-8684 to reach a Customer Support representative. Please have your unit’s model number
and serial number ready when you call. See the previous section to locate this information.
Copyright© 2003 Cub Cadet LLC
All Rights Reserved
S/N :
ITEM :
MODEL :
Copy the model and parent part
number here:
Copy the serial number here:
To the Owner
Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. You
will find it to be a great labor-saving device. This operator’s manual provides you with easy-to-understand operating
instructions. Before starting or operating this equipment, read the whole manual and follow all the instructions to keep
your new outdoor power tool in top operating condition.
All information, illustrations and specifications in this manual are based on the latest product information available at the
time of printing. We reserve the right to make changes at any time without notice. Service on this unit both within and
after the warranty period should be performed only by a Cub Cadet dealer. Proof of purchase will be required for
warranty service.
3
READ ALL INSTRUCTIONS
Before Operating
Read the instructions carefully. Be familiar with the
controls and proper use of the unit.
Do not operate this unit when tired, ill or under the
influence of alcohol, drugs or medication.
Children and teens under the age of 15 must not use
the unit, except for teens guided by an adult.
Inspect the unit before use. Replace damaged parts.
Check for fuel leaks. Make sure all fasteners are in
place and secure. Replace cutting attachment parts
that are cracked, chipped or damaged in any way.
Make sure the cutting attachment is properly installed
and securely fastened. Be sure the cutting attachment
shield is properly attached, and positioned as
recommended. Failure to do so can result in personal
injury to the operator and bystanders, as well as
damage to the unit.
Use only 0.095 inch (
2.41 mm) diameter Genuine
Factory Parts™ replacement line. Never use metal-
reinforced line, wire or rope. These can break off and
become dangerous projectiles.
Be aware of the risk of injury to the head, hands and
feet.
Clear the area to be cut before each use. Remove all
objects such as rocks, broken glass, nails, wire or
string. They can be thrown or become entangled in the
cutting attachment. Clear the area of children,
bystanders, and pets. At a minimum, keep all children,
bystanders and pets outside a 50-foot (15 m.) radius;
there still may be a risk to bystanders from thrown
objects. Bystanders should be encouraged to wear
eye protection. If you are approached, stop the engine
and cutting attachment immediately.
Squeeze the throttle control and check that it returns
automatically to the idle position. Make all adjustments
or repairs before using unit.
This unit was not designed to be used as a
brushcutter. Do not attach or operate this unit with any
type of brushcutting blade or brushcutting attachment.
SAFETY ALERT SYMBOL: Indicates danger,
warning or caution. Attention is required in
order to avoid serious personal injury. May
be used in conjunction with other symbols
or pictographs.
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their
explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate
any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.
NOTE: Advises you of information or instructions
vital to the operation or maintenance of the
equipment.
SYMBOL MEANING
Section 1
Safety
Failure to obey a safety warning will result in
serious injury to yourself or to others. Always
follow the safety precautions to reduce the risk of
fire, electric shock, and personal injury.
Failure to obey a safety warning can result in
injury to yourself and others. Always follow the
safety precautions to reduce the risk of fire,
electric shock, and personal injury.
Failure to obey a safety warning may result in property
damage or personal injury to yourself or to others.
Always follow the safety precautions to reduce the
risk of fire, electric shock, and personal injury.
THE ENGINE EXHAUST FROM THIS PRODUCT
CONTAINS CHEMICALS KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS
OR OTHER REPRODUCTIVE HARM.
California Proposition 65 Warning
Important Safety Information
4
Use the right tool. Only use this tool for the purpose
intended.
Do not overreach. Always keep proper footing and
balance.
Always hold the unit with both hands when operating.
Keep a firm grip on both the front and rear handle or
grips.
Keep hands, face, and feet at a distance from all
moving parts. Do not touch or try to stop the cutting
attachment when it is rotating.
Do not touch the engine or muffler. These parts get
extremely hot from operation. They remain hot for a
short time after you turn off the unit.
Do not operate the engine faster than the speed
needed to cut, trim or edge. Do not run the engine at
high speed when you are not cutting.
Always stop the engine when cutting is delayed or
when walking from one cutting location to another.
If you strike or become entangled with a foreign
object, stop the engine immediately and check for
damage. Do not operate before repairing damage. Do
not operate the unit with loose or damaged parts.
Stop and switch the engine to off for maintenance,
repair, or for changing the cutting attachment or other
attachments.
Use only Genuine Factory Parts™ replacement parts
and accessories for this unit. These are available from
your authorized service dealer. Use of any
unauthorized parts or accessories could lead to
serious injury to the user, or damage to the unit, and
void your warranty.
Keep unit clean of vegetation and other materials.
They may become lodged between the cutting
attachment and shield.
•To reduce fire hazard, replace faulty muffler and spark
arrestor, keep the engine and muffler free from grass,
leaves, excessive grease or carbon build up.
Other Safety Warnings
Never store the unit, with fuel in the tank, inside a
building where fumes may reach an open flame or
spark.
Allow the engine to cool before storing or transporting.
Be sure to secure the unit while transporting.
Store the unit in a dry area, locked up or up high
to prevent unauthorized use or damage, out of the
reach of children.
Never douse or squirt the unit with water or any other
liquid. Keep handles dry, clean and free from debris.
Clean after each use. See the Cleaning and Storage
instructions.
Keep these instructions. Refer to them often and use
them to instruct other users. If you loan someone this
unit, also loan them these instructions.
SAVE THESE INSTRUCTIONS
While Operating
Never start or run the unit inside a closed room or
building. Breathing exhaust fumes can kill. Operate
this unit only in a well ventilated outdoor area.
Wear safety glasses or goggles that are marked as
meeting ANSI Z87.1-1989 standards. Also wear
ear/hearing protection when operating this unit. Wear
a face or dust mask if the operation is dusty. Long
sleeve shirts are recommended.
Wear heavy, long pants, boots and gloves. Do not
wear loose clothing, jewelry, short pants, sandals or
go barefoot. Secure hair above shoulder level.
The cutting attachment shield must always be in place
while operating the unit. Do not operate unit without
both trimming lines extended, and the proper line
installed. Do not extend the trimming line beyond the
length of the shield.
This unit has a clutch. The cutting attachment remains
stationary when the engine is idling. If it does not, have
the unit adjusted by an authorized service technician.
Adjust the D-handle to your size to provide the best
grip.
Be sure the cutting attachment is not in contact with
anything before starting the unit.
Use the unit only in daylight or good artificial light.
Avoid accidental starting. Be in the starting position
whenever pulling the starter rope. The operator and
unit must be in a stable position while starting. See
Starting/Stopping Instructions.
Store fuel only in containers specifically designed and
approved for the storage of such materials.
Always stop the engine and allow it to cool before
filling the fuel tank. Never remove the cap of the fuel
tank, or add fuel, when the engine is hot. Never
operate the unit without the fuel cap securely in place.
Loosen the fuel tank cap slowly to relieve any pressure
in the tank.
Add fuel in a clean, well-ventilated outdoor area where
there are no sparks or flames. Slowly remove the fuel
cap only after stopping engine. Do not smoke while
fueling or mixing fuel. Wipe up any spilled fuel from the
unit immediately.
Avoid creating a source of ignition for spilled fuel. Do
not start the engine until fuel vapors dissipate.
Move the unit at least 30 feet (9.1 m) from the fueling
source and site before starting the engine. Do not
smoke. Keep sparks and open flames away from the
area while adding fuel or operating the unit.
Safety (continued)
Gasoline is highly flammable, and its vapors can
explode if ignited. Take the following precautions.
Safety Warnings for Gas Trimmers
5
SYMBOL MEANING
SAFETY ALERT SYMBOL
Indicates danger, warning, or
caution. May be used in conjunction
with other symbols or pictographs.
WARNING - READ OPERATOR'S
MANUAL
Read the Operator’s Manual(s) and
follow all warnings and safety
instructions. Failure to do so can
result in serious injury to the
operator and/or bystanders.
WEAR EYE AND HEARING
PROTECTION
WARNING: Thrown objects and
loud noise can cause severe eye
injury and hearing loss. Wear eye
protection meeting ANSI Z87.1-1989
standards and ear protection when
operating this unit.
Use a full face
shield when needed.
KEEP BYSTANDERS AWAY
WARNING
:
Keep all bystanders,
especially children and pets, at least
50 feet (15 m.) from the operating area.
UNLEADED FUEL
Always use clean, fresh unleaded fuel.
OIL
Refer to operator's manual for the
proper type of oil.
Safety and International Symbols
This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING
THROWN OBJECTS AND
ROTATING CUTTER CAN CAUSE
SEVERE INJURY
WARNING
:
Do not operate without
the cutting attachment shield in
place. Keep away from the rotating
cutting attachment.
•ON/OFF STOP CONTROL
ON / START / RUN
•ON/OFF STOP CONTROL
OFF OR STOP
HOT SURFACE WARNING
Do not touch a hot muffler or
cylinder. You may get burned. These
parts get extremely hot from
operation. When turned off they
remain hot for a short time.
SHARP BLADE
WARNING: Sharp blade on cutting
attachment shield. To prevent
serious injury, do not
touch line cutting blade.
Safety (continued)
6
Applications
As a trimmer:
Cutting grass and light weeds
Edging
Decorative trimming around trees, fences, etc.
Know Your Unit
Section 2
Shaft Grip
Cutting Attachment Shield
Fuel Cap
Throttle Control
D-Handle
Line Cutting Blade
Cutting Attachment
Primer Bulb
Choke Lever
Air Filter Cover
Spark Plug
On/Off Stop Control
Shaft Housing
Starter Rope Grip
7
Install and Adjust the D-handle
1. Remove the screws and bottom clamp piece that
were installed on the D-handle for shipping.
2. Place D-handle the over the shaft housing and onto
the bottom clamp (Fig. 3-1). Place it a minimum of 6
inches (15.24 cm) from the end of the shaft grip.
3. Start screws with a large Flat-head or T-25 Torx
screwdriver. Do not tighten until you make the
handle adjustment.
4. If it was pre-installed, loosen the screws on the
D-handle just enough to move the D-handle.
5. While holding the unit in the operating position
(Fig. 3-2), move the D-handle to the location that
provides you the best grip.
6. Tighten the clamp screws evenly, until the D-handle
is secure.
Install the Cutting Attachment Shield
Use the following instructions if the cutting attachment
shield on your unit is not installed.
1. Place the cutting attachment shield onto the shaft
housing above the clamp assembly (Fig. 3-3).
To prevent serious personal injury, never operate
the trimmer without the cutting attachment shield
in place.
2. Push the cutting attachment shield down to the top of
the cutting attachment assembly and then rotate the
cutting attachment shield until the screw holes align
and the guard fits into the recessed pocket (Fig. 3-3).
3. Install the screws with a Phillips screwdriver (Fig. 3-4).
Assembly
Section 3
(4) Screws
(4) Screws
Shaft
Housing
D-Handle
Bottom Clamp
Fig. 3-1
Fig. 3-2
(4) Nuts
Shaft Grip
Minimum 6 inches
(15.24 cm)
Fig. 3-3
Cutting
Attachment
Shield
Cutting
Attachment
Clamp
Recessed
Pocket
Fig. 3-4
8
NOTE: One gallon (3.8 liters) of unleaded gasoline
mixed with one 3.2 oz. (95 ml) bottle of
2-cycle oil makes a 40:1 fuel/oil ratio.
Gasoline is extremely flammable. Ignited Vapors
may explode. Always stop the engine and allow it
to cool before filling the fuel tank. Do not smoke
while filling the tank. Keep sparks and open flames
at a distance from the area.
Remove fuel cap slowly to avoid injury from fuel
spray. Never operate the unit without the fuel cap
securely in place.
Add fuel in a clean, well ventilated area outdoors.
Wipe up any spilled fuel immediately. Avoid
creating a source of ignition for spilt fuel. Do not
start the engine until fuel vapors dissipate.
NOTE: Dispose of the old fuel/oil mix in accordance
to Federal, State and Local regulations.
Oil and Fuel Mixing Instructions
Old and/or improperly mixed fuel are the main reasons
for the unit not running properly. Be sure to use fresh,
clean unleaded fuel. Follow the instructions carefully for
the proper fuel/oil mixture.
Definition of Blended Fuels
Today's fuels are often a blend of gasoline and
oxygenates such as ethanol, methanol, or MTBE (ether).
Alcohol-blended fuel absorbs water. As little as 1%
water in the fuel can make fuel and oil separate. It forms
acids when stored. When using alcohol-blended fuel,
use fresh fuel (less than 60 days old).
Using Blended Fuels
If you choose to use a blended fuel, or its use is
unavoidable, follow recommended precautions:
Always use the fresh fuel mix explained in your
operator's manual
Always agitate the fuel mix before fueling the unit
Drain the tank and run the engine dry before storing
the unit
Using Fuel Additives
The bottle of 2-cycle oil that came with your unit
contains a fuel additive which will help inhibit corrosion
and minimize the formation of gum deposits. It is
recommended that you use our 2-cycle oil with this unit.
If unavailable, use a good 2-cycle oil designed for
air-cooled engines along with a fuel additive, such as
STA-BIL
®
Gas Stabilizer or an equivalent. Add 0.8 oz.
(23 ml.) of fuel additive per gallon of fuel according to the
instructions on the container. NEVER add fuel additives
directly to the unit's fuel tank.
For proper engine operation and maximum
reliability, pay strict attention to the oil and fuel
mixing instructions on the 2-cycle oil container.
Using improperly mixed fuel can severely damage
the engine.
Thoroughly mix the proper ratio of 2-cycle engine oil
with unleaded gasoline in a separate fuel can. Use a 40:1
fuel/oil ratio. Do not mix them directly in the engine fuel
tank. See the table below for specific gas and oil mixing
ratios.
Oil and Fuel
Section 4
UNLEADED GAS 2 CYCLE OIL
1 GALLON US
(3.8 LITERS)
3.2 FL. OZ.
(95 ml)
1 LITER 25 ml
+
MIXING RATIO - 40:1
9
Operate this unit only in a well-ventilated outdoor
area. Carbon monoxide exhaust fumes can be
lethal in a confined area.
Avoid accidental starting. Make sure you are in the
starting position when pulling the starter rope
(Fig. 5-3). To avoid serious injury, the operator and
unit must be in a stable position while starting.
Starter Rope
Throttle Control
(Squeezed)
Primer Bulb
Run
Start
Choke Lever
On/Off Stop Control
Start/
On (I)
Stop/
Off (O)
Fig. 5-1
Fig. 5-2
Fig. 5-3
Operation
Section 5
Starting Instructions
1. Mix gas with oil. Fill fuel tank with fuel/oil mixture.
See Oil and Fuel Mixing Instructions.
2. Put the On/Off Stop Control in the ON (I) position
(Fig. 5-1).
3. Fully press and release the primer bulb 10 times,
slowly, until FUEL IS VISIBLE IN THE PRIMER
BULB (Fig. 5-2). If you can’t see fuel in the bulb,
press and release the bulb as many times as it takes
before you can see fuel in it.
4. Place the choke lever in the START () position
(Fig. 5-2).
5. With the unit in the starting position (Fig. 5-3), squeeze
the throttle control to the wide open (full throttle)
position. Pull the starter rope briskly 5 times while still
in the START () position. If the engine attempts to
run before the fifth pull, proceed to step 6.
6. Place the choke lever in the RUN () position (Fig. 5-2).
7. Pull starter rope 1 to 3 times, briskly, to start the
engine (Fig. 5-3).
NOTE: Squeeze the throttle control until the engine
has started and warmed up.
8. If the engine does not start, repeat steps 3 through 7.
NOTE: If the engine floods while trying to start, place
the choke lever in the RUN ( ) position
(Fig. 5-2). Squeeze the throttle control. Pull the
starter rope briskly. The engine should start
within three (3) to eight (8) pulls.
9. Squeeze the throttle control to warm up the engine
for 5 to 10 seconds. Place the choke lever in the
RUN () position (Fig. 5-2).
NOTE: Choking is unnecessary when starting a
warm engine. Put the On/Off Stop Control in
the ON position (Fi. 5-1), and the choke lever
in the RUN ( ) position (Fig. 5-2). Pull the
starter rope.
Stopping Instructions
1. Release your hand from the throttle control (Fig. 5-3).
Allow the engine to cool down by idling.
2. Put the On/Off Stop Control in the OFF (O) position
(Fig. 5-1).
10
Operation (continued)
Fig. 5-4
Fig. 5-5
Fig. 5-6
Holding the Trimmer
Always wear eye, hearing, foot and body
protection to reduce the risk of injury when
operating this unit.
Before operating the unit, stand in the operating position
(Fig. 5-4). Check for the following:
The operator is wearing eye protection and proper
clothing
With a slightly-bent right arm, the operator’s hand is
holding the shaft grip
The operator’s left arm is straight, the left hand
holding the D-handle
The unit is at waist level
The cutting attachment is parallel to the ground and
easily contacts the grass without the need to bend ove
r
Adjusting Trimming Line Length
The Bump Head cutting attachment allows you to release
trimming line without stopping the engine. To release
more line, lightly tap the cutting attachment on the ground
(Fig. 5-5) while operating the trimmer at high speed.
NOTE: Always keep the trimming line fully
extended. Line release becomes more
difficult as cutting line becomes shorter.
Each time the head is bumped, about 1 inch (25.4 mm) of
trimming line releases. A blade in the cutting attachment
shield will cut the line to the proper length if any excess
line is released.
For best results, tap the bump knob on bare ground or
hard soil. If you attempt a line release in tall grass, the
engine may stall. Always keep the trimming line fully
extended. Line release becomes more difficult when the
cutting line gets shorter.
NOTE: Do not rest the Bump Head on the ground
while the unit is running.
Do not remove or alter the line cutting blade
assembly. Excessive line length will make the
clutch overheat. This may lead to serious personal
injury or damage to the unit.
Some line breakage will occur from:
Entanglement with foreign matter
Normal line fatigue
Attempting to cut thick, stalky weeds
Forcing the line into objects such as walls or fence
posts
Tips for Best Trimming Results
Keep the cutting attachment parallel to the ground.
Do not force the cutting attachment. Allow the tip of
the line to do the cutting, especially along walls.
Cutting with more than the tip will reduce cutting
efficiency and may overload the engine.
Cut grass over 8 inches (200 mm) by working from
top to bottom in small increments to avoid premature
line wear or engine drag.
Cut from right to left whenever possible. Cutting to
the left improves the unit's cutting efficiency.
Clippings are thrown away from the operator.
Slowly move the trimmer into and out of the cutting
area at the desired height. Move either in a forward-
backward or side-to-side motion. Cutting shorter
lengths produces the best results.
Trim only when grass and weeds are dry.
The life of your cutting line is dependent upon:
Following the trimming techniques
What vegetation is being cut
Where vegetation is cut
For example, the line will wear faster when trimming
against a foundation wall as opposed to trimming around
a tree.
Decorative Trimming
Decorative trimming is accomplished by removing all
vegetation around trees, posts, fences and more.
Rotate the whole unit so that the cutting attachment is at
a 30° angle to the ground (Fig. 5-6).
11
NOTE: Maintenance, replacement or repair of the
emission control devices and system may be
performed by any non-road engine repair
establishment, individual or authorized
service dealer.
In order to assure peak performance of your engine,
inspection of the engine exhaust port may be necessary
after 50 hours of operation. If you notice lost RPM, poor
performance or general lack of acceleration, this service
may be required. If you feel your engine is in need of this
inspection, refer service to any non-road engine repair
establishment, individual or authorized service dealer for
repair. DO NOT attempt to perform this process yourself
as engine damage may result from contaminants
involved in the cleaning process for the port.
FREQUENCY MAINTENANCE REQUIRED REFER TO
Before starting engine Fill fuel tank with fresh fuel Page 8
Every 10 hours Clean and re-oil air filter Page 14
Every 25 hours
Check and clean spark arrestor
Check spark plug condition and gap
Page 14
Page 16
Every 50 hours
Inspect exhaust port and spark arrestor screen for clogging or
obstruction to assure maximum performance levels
Page 14
Maintenance
Section 6
Maintenance Schedule
Perform these required maintenance procedures at the
frequency stated in the table. These procedures should
also be a part of any seasonal tune-up.
NOTE: Some maintenance procedures may require
special tools or skills. If you are unsure about
these procedures take your unit to any non-
road engine repair establishment.
To prevent serious injury, never perform
maintenance or repairs with unit running. Always
service and repair a cool unit. Disconnect the spark
plug wire to ensure that the unit cannot start.
Bump Knob
Bolt
Fig. 6-1
Line Installation
This section covers both SplitLine™ and standard single
line installation.
Always use Genuine Factory Parts™ 0.095 in. (2.41 mm)
replacement line. Using line other than the specified may
make the engine overheat or fail.
Never use metal-reinforced line, wire, chain, or
rope. These can break off and become dangerous
projectiles.
There are two methods to replace the trimming line:
• Wind the inner reel with new line
• Install a prewound inner reel
12
Fig. 6-4
Inner Reel
Outer Spool
Spring
Shaft
Indexing Teeth
Fig. 6-3
Slotted Holes
For Use with
Membrane or
Single Line
For Use with
Single Line ONLY
Fig. 6-2
Fig. 6-5
Loop
Maintenance (continued)
Winding the Existing Inner Reel
1. Hold the outer spool with one hand and unscrew the
bump knob counterclockwise (Fig. 6-1). Inspect the
bolt inside the bump knob to make sure it moves
freely. Replace the bump knob if damaged.
2. Remove the inner reel from the outer spool (Fig. 6-2).
3. Remove spring from the inner reel (Fig. 6-2).
4. Use a clean cloth to wipe the inner reel, spring, shaft
and inner surface of the outer spool.
5. Check the indexing teeth on the inner reel and outer
spool for wear. If necessary, remove burrs or replace
the reel and spool (Fig. 6-3).
NOTE: SplitLine™ can only be used with the inner
reel containing slotted holes. Single line can
be used on either type of inner reel. Use
Figure 6-4 to identify the inner reel you have.
NOTE: Always use the correct line length when
installing trimming line on the unit. The line
may not release properly if the line is too long.
Single Line Installation
Go To Step 8 for SplitLine™ Installation
6. Cut approximately 25 feet (7.6 m) of new trimming
line, then loop it into two equal lengths. Insert each
end of the line through one of the two holes in the
inner reel. Pull the line through the inner reel so that
the loop is as small as possible (Fig. 6-5).
7. Wind the lines in tight even layers onto the reel. See
(Fig. 6-6). Wind the line in the direction indicated on
the inner reel. Place your index finger between the
two lines to stop the lines from overlapping. Do not
overlap the ends of the line. Proceed to step 11.
SplitLine™ Installation
8. Cut approximately 12 feet (3.65 m) of new trimming
line. Insert one end of the line through one of the two
holes in the inner reel. Pull the line through the inner
reel until only about 4 inches is left out.
9. Insert the end of the line into the open hole in the
inner reel and pull the line tight to make the loop as
small as possible (Fig. 6-7).
10. Before winding, split the line back about 6 inches.
11. Wind the line in tight even layers in the direction
indicated on the inner reel.
NOTE: Failure to wind the line in the direction
indicated will cause the cutting attachment to
operate incorrectly.
13
Maintenance (continued)
Fig. 6-6
Fig. 6-7
Loop
Holding Slots
Fig. 6-8
Fig. 6-9
12. Insert the ends of the line into the two holding slots
(Fig. 6-8).
13. Insert the ends of the line through the eyelets in the
outer spool and place the inner reel with spring inside
the outer spool (Fig. 6-9). Push the inner reel and
outer spool together. While holding the inner reel and
outer spool, grasp the ends and pull firmly to release
the line from the holding slots in the reel.
NOTE: The spring must be assembled on the inner
reel before reassembling the cutting
attachment.
14. Hold the inner reel in place and install the bump knob
by turning clockwise. Tighten securely.
Installing a Pre Wound Reel
1. Hold the outer spool with one hand and unscrew the
bump knob counterclockwise (Fig. 6-1). Inspect the
bolt inside the bump knob to make sure it moves
freely. Replace the bump knob if damaged.
2. Remove the old inner reel from the outer spool (Fig. 6-2).
3. Remove the spring from the old inner reel (Fig. 6-2).
4. Place the spring in the new inner reel.
NOTE: The spring must be assembled on the inner
reel before reassembling the cutting
attachment.
5. Insert the ends of the line through the eyelets in the
outer spool (Fig. 6-9).
6. Place the new inner reel inside the outer spool. Push
the inner reel and outer spool together. While holding
the inner reel and outer spool, grasp the ends and
pull firmly to release the line from the holding slots in
the reel.
7. Hold the inner reel in place and install the bump knob
by turning clockwise. Tighten securely.
Replacement Parts
For replacement parts, refer to the Accessories /
Replacement Parts section.
14
Fig. 6-10
Fig. 6-12
Fig. 6-11
Air Filter Maintenance
Cleaning the Air Filter
To avoid serious personal injury, always turn your
trimmer off and allow it to cool before you clean or
service it.
Clean and re-oil the air filter every 10 hours of operation.
It is an important item to maintain. Failure to maintain the
air filter will VOID the warranty.
1. Remove the carburetor/air filter cover by pushing on
the tab on top of the cover (Fig. 6-10).
2. Remove the air filter (Fig. 6-11).
3. Wash the filter in detergent and water. Rinse the
filter thoroughly and allow it to dry.
4. Apply enough clean SAE 30 motor oil to lightly coat
the filter (Fig. 6-12).
5. Squeeze the filter to spread and remove excess oil
(Fig. 6-12).
6. Reinstall the filter (Fig. 6-11) and air filter cover
(Fig. 6-10).
NOTE: If the unit is operated without the air filter, you
will VOID the warranty.
Spark Arrestor Maintenance
To avoid serious personal injury, always turn your
trimmer off and allow it to cool before you clean or
service it.
1. Turn the powerhead so the back of the engine is
facing forward. In this position, the starter rope is to
the left (Fig. 6-13).
Carburetor/ Air
Filter Cover
Air Filter
Tab
Fig. 6-13
Spark
Arrestor
Collar
Maintenance (continued)
15
2. Use a needle-nose pliers to grasp the collar of the
spark arrestor and pull it out of the muffler (Fig. 6-14).
NOTE: Use only a needle-nose pliers. Other pliers or
tools may damage the spark arrestor.
3. Clean the spark arrestor with a wire brush. Replace it if
it is damaged or if you are unable to clean it thoroughly.
4. Reinstall spark arrestor. Use the needle-nose pliers
to gently push the spark arrestor back into the
muffler until it snaps into place.
Carburetor Adjustment
The idle speed of the engine is adjustable by the screw
next to the air filter cover (Fig 6-15).
NOTE: Careless adjustments can seriously damage
your unit. An authorized service dealer
should make carburetor adjustments.
Fig. 6-14
Check Fuel Mixture
Old and/or improperly mixed fuel is usually the reason for
improper unit performance. Drain and refill the tank with
fresh, properly mixed fuel prior to making any
adjustments. Refer to Oil and Fuel Information.
Clean Air Filter
The condition of the air filter is important to the operation
of the unit. A dirty air filter will restrict air flow and change
the air/fuel mixture. This is often mistaken for an out of
adjustment carburetor. Check the condition of the air
filter before adjusting the idle speed screw. Refer to Air
Filter Maintenance.
Adjust Idle Speed Screw
The cutting attachment may be spinning during
idle speed adjustment. Wear protective clothing
and observe all safety instructions to prevent
serious personal injury.
If, after checking the fuel mixture and cleaning the air
filter, the engine still will not idle, adjust the idle speed
screw as follows:
1. Start the engine and let it run at a high idle for a
minute to warm up.
2. Release the throttle trigger and let the engine idle. If
the engine stops, insert a small phillips or flat blade
screwdriver into the screw next to the air filter cover
(Fig. 6-15). Turn the idle speed screw in, clockwise,
1/8 of a turn at a time (as needed) until the engine
idles smoothly.
NOTE: The cutting attachment should not rotate
when the engine idles.
3. If the cutting attachment rotates when the engine
idles, turn the idle speed screw counterclockwise 1/8
of a turn at a time (as needed), to reduce idle speed.
Checking the fuel mixture, cleaning the air filter, and
adjusting the idle speed screw should solve most engine
problems. If not and all the following are true:
The engine will not idle
The engine hesitates or stalls on acceleration
There is a loss of engine power
Have the carburetor adjusted by an authorized service
dealer.
Fig. 6-15
Idle Speed Screw
Maintenance (continued)
16
Cleaning
To avoid serious personal injury, always turn your
trimmer off and allow it to cool before you clean or
do any maintenance on it.
Use a small brush to clean off the outside of the unit. Do
not use strong detergents. Household cleaners that
contain aromatic oils such as pine and lemon, and
solvents such as kerosene, can damage plastic housing
or handle. Wipe off any moisture with a soft cloth.
Accessories / Replacement Parts
2-Cycle Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180965
Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181765
Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . .181696
Replacement Line Cartridge . . . . . . . . . . . . . . 753-1156
Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . .182842
Bump Knob Assembly . . . . . . . . . . . . . . . . . . . .153066
Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .181612
Shoulder Strap . . . . . . . . . . . . . . . . . . . . . . . . . . 682075
For specific replacement parts, refer to the parts list
located on the inside back cover of this manual.
Storage
Never store the unit with fuel in the tank where fumes
may reach an open flame or spark.
Allow the engine to cool before storing.
Store the unit locked up to prevent unauthorized use or
damage.
Store the unit in a dry, well-ventilated area.
Store the unit out of the reach of children.
Long Term Storage
If the unit will be stored for an extended time, use the
following storage procedure:
1. Drain all fuel from the fuel tank into a container with
the same 2-cycle fuel mixture. Do not use fuel that
has been stored for more than 60 days. Dispose of
the old fuel/oil mix in accordance to Federal, State
and Local regulations.
2. Start the engine and allow it to run until it stalls. This
ensures that all fuel has been drained from the
carburetor.
3. Allow the engine to cool. Remove the spark plug and
put 1 oz. (30 ml) of any high quality motor oil or
2-cycle oil into the cylinder. Pull the starter rope
slowly to distribute the oil. Reinstall the spark plug.
NOTE: Remove the spark plug and drain all of the oil
from the cylinder before attempting to start
the trimmer after storage.
4. Thoroughly clean the unit and inspect it for any loose
or damaged parts. Repair or replace damaged parts
and tighten loose screws, nuts or bolts. The unit is
ready for storage.
Transporting
Allow the engine to cool before transporting.
Drain fuel from unit.
Tighten fuel cap before transporting.
Secure the unit while transporting.
0.025 inch
(0.655 mm)
Fig. 6-16
Replacing the Spark Plug
Use a Champion RCJ6Y spark plug (or equivalent). The
correct air gap is 0.025 inch (0.655 mm). Remove the
plug after every 25 hours of operation and check its
condition.
1. Stop the engine and allow it to cool. Grasp the plug
wire firmly and pull the cap from the spark plug.
2. Clean dirt from around the spark plug. Remove the
spark plug from the cylinder head by turning a 5/8
inch socket counterclockwise.
3. Replace cracked, fouled or dirty spark plug. Set the
air gap at 0.025 inch (0.655 mm) using a feeler gauge
(Fig. 6-16).
Do not sand blast, scrape, or clean electrodes. Grit
in the engine could damage the cylinder.
4. Install a correctly-gapped spark plug in the cylinder
head. Tighten by turning the 5/8 inch socket
clockwise until snug.
If using a torque wrench torque to:
110-120 in.•lb. (12.3-13.5 N•m).
Do not over tighten.
Maintenance (continued)
17
If further assistance is required, contact your authorized service dealer.
CAUSE ACTION
Cutting attachment bound with grass Stop the engine and clean cutting attachment
Cutting attachment out of line Refill with new line
Inner reel bound up Replace the inner reel
Cutting head dirty Clean inner reel and outer spool
Line welded Disassemble, remove the welded section and rewind
Line twisted when refilled Disassemble and rewind the line
Not enough line is exposed Push the bump knob and pull out line until 4 inches
(102 mm) of line is outside of the cutting attachment
CAUSE ACTION
Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture
Improper carburetor adjustment Take to an authorized service dealer for an adjustment
Fouled spark plug Replace or clean the spark plug
Plugged spark arrestor Clean or replace spark arrestor
CAUSE ACTION
On/Off stop control is in the OFF position Turn the on/off stop control to ON
Empty fuel tank Fill fuel tank with properly mixed fuel
Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times
Engine is flooded Squeeze the trigger and pull the starter rope
Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture
Fouled spark plug Replace or clean the spark plug
Plugged spark arrestor Clean or replace spark arrestor
ENGINE WILL NOT START
ENGINE WILL NOT IDLE
ENGINE WILL NOT ACCELERATE
ENGINE LACKS POWER OR STALLS WHEN CUTTING
CAUSE ACTION
Air filter is plugged Replace or clean the air filter
Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture
Improper carburetor adjustment Adjust according to the Carburetor Adjustments section
CAUSE ACTION
Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture
Improper carburetor adjustment Take to an authorized service dealer for an adjustment
Cutting attachment bound with grass Stop the engine and clean the cutting attachment
Dirty air filter Clean or replace the air filter
Plugged spark arrestor Clean or replace spark arrestor
CUTTING ATTACHMENT WILL NOT ADVANCE LINE
CAUSE ACTION
Oil, cleaner or lubricant in cutting head Clean and thoroughly dry the cutting head
CUTTING LINE ADVANCES UNCONTROLLABLY
Troubleshooting
Section 7
18
ENGINE*
DRIVE SHAFT & CUTTING ATTACHMENT*
*All specifications are based on the latest product information available at the time of printing. We reserve the right to
make changes at any time without notice.
Engine Type.......................................................................................................................................... Air-Cooled, 2-Cycle
Stroke.................................................................................................................................................... 1.25 in. (31.75 mm)
Displacement............................................................................................................................................. 1.4 cu in. (25 cc)
Clutch Type ......................................................................................................................................................... Centrifugal
Idle Speed RPM ...................................................................................................................................... 2,400 - 3,600 rpm
Operating RPM.................................................................................................................................................. 7,200+ rpm
Ignition Type.......................................................................................................................................................... Electronic
Ignition Switch................................................................................................................................................ Toggle Switch
Spark Plug Gap................................................................................................................................... 0.025 in. (0.655 mm)
Lubrication................................................................................................................................................... Fuel/Oil Mixture
Fuel/Oil Ratio.................................................................................................................................................................. 40:1
Carburetor....................................................................................................................................... Diaphragm, All-Position
Starter............................................................................................................................................................... Auto Rewind
Muffler..................................................................................................................................................... Baffled with Guard
Throttle............................................................................................................................................... Manual Spring Return
Fuel Tank Capacity........................................................................................................................................ 20 oz. (591 ml)
Drive Shaft Housing .................................................................................................................................... Aluminum Tube
Throttle Control ........................................................................................................................................ Finger-Tip Trigger
Approximate Unit Weight (No fuel, with cutting attachment, shield and D-handle).................................. 9.5 lbs. (4.25 kg)
Cutting Mechanism....................................................................................................................... Dual String Cutting Head
Line Spool............................................................................................................................................. Bump Line Releaser
Line Spool Diameter............................................................................................................................ 4 inches (101.6 mm)
Trimming Line Diameter ................................................................................................................. 0.095 inches (2.41 mm)
Cutting Path Diameter ........................................................................................................................ 17 inches (43.18 cm)
Specifications
Section 8
19
EPA Emission Control Warranty Statement
Your Warranty Rights and Obligations
The Environmental Protection Agency and Cub Cadet LLC (Cub Cadet) are pleased to explain the emission control
system warranty on your 2002 and later small off-road engine. New small off-road engines must be designed, built and
equipped to meet stringent anti-smog standards. Cub Cadet must warrant the emission control system on your small
off-road engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance
of your small off-road engine.
Your emission control system may include parts such as the carburetor or fuel-injected system, the ignition system, and
catalytic converter. Also included may be hoses, belts, connectors and other emission-related assemblies.
Where a warrantable condition exists, Cub Cadet will repair your small off-road engine at no cost to you including
diagnosis, parts and labor.
The 2002 and later small off-road engines are warranted for two years. If any emission-related part on your engine is
defective, the part will be repaired or replaced by Cub Cadet.
Owners Warranty Responsibilities
• As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your
operator’s manual. Cub Cadet recommends that you retain all receipts covering maintenance on your small off-road
engine, but Cub Cadet cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance
of all scheduled maintenance.
• As the small off-road engine owner, you however should be aware that Cub Cadet may deny you warranty coverage if
your small off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved
modifications.
• You are responsible for presenting your small off-road engine to a Cub Cadet Authorized Service Center as soon as a
problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should call 1-877-282-8684.
Manufacturer’s Warranty Coverage
• The warranty period begins on the date the engine or equipment is delivered to the retail purchaser.
• The manufacturer warrants to the initial owner and each subsequent purchaser, that the engine is free from defects in
material and workmanship which cause the failure of a warranted part for a period of two years.
• Repair or replacement of warranted part will be performed at no charge to the owner at an Authorized Cub Cadet
Service Center. For the nearest location please contact Cub Cadet at: 1-877-282-8684.
• Any warranted part which is not scheduled for replacement, as required maintenance or which is scheduled for only
for regular inspection to the effect of “Repair or Replace as Necessary” is warranted for the warranty period. Any
warranted part which is scheduled for replacement as required maintenance will be warranted for the period of time up
to the first scheduled replacement point for that part.
• The owner will not be charged for diagnostic labor which leads to the determination that a warranted part is defective,
if the diagnostic work is performed at an Authorized Cub Cadet Service Center.
• The manufacturer is liable for damages to other engine components caused by the failure of a warranted part still
under warranty.
• Failures caused by abuse, neglect or improper maintenance are not covered under warranty.
• The use of add-on or modified parts can be grounds for disallowing a warranty claim. The manufacturer is not liable to
cover failures of warranted parts caused by the use of add-on or modified parts.
• In order to file a claim, go to your nearest Authorized Cub Cadet Service Center. Warranty services or repairs will be
provided at all Authorized Cub Cadet Service Centers.
• Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repair
of emission related parts and will be provided without charge to the owner. Any replacement part that is equivalent in
performance or durability may be used in non-warranty maintenance or repair and will not reduce the warranty
obligations of the manufacturer
• The following components are included in the emission related warranty of the engine, air filter, carburetor, primer, fuel
lines, fuel pick up/ fuel filter, ignition module, spark plug and muffler.
MANUFACTURER’S LIMITED WARRANTY FOR:
No implied warranty, including any implied warranty of
merchantability or fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty or guaranty, whether written or oral,
except as mentioned above, given by any person or
entity, including a dealer or retailer, with respect to any
product shall bind Cub Cadet LLC During the period of
the Warranty, the exclusive remedy is repair or
replacement of the product as set forth above. (Some
states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to
you.)
The provisions as set forth in this Warranty provide the
sole and exclusive remedy arising from the sales. Cub
Cadet LLC shall not be liable for incidental or
consequential loss or damages including, without
limitation, expenses incurred for substitute or
replacement lawn care services, for transportation or
for related expenses, or for rental expenses to
temporarily replace a warranted product. (Some states
do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you.)
In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold.
Alteration of the safety features of the product shall void
this Warranty. You assume the risk and liability for loss,
damage, or injury to you and your property and/or to
others and their property arising out of the use or misuse
or inability to use the product.
This limited warranty shall not extend to anyone other than
the original purchaser, original lessee or the person for
whom it was purchased as a gift.
How State Law Relates to this Warranty: This warranty
gives you specific legal rights, and you may also have
other rights which vary from state to state.
To locate your nearest service dealer dial
1-877-282-8684.
Cub Cadet LLC
P.O. Box 361131
Cleveland, OH 44136-0019
The limited warranty set forth below is given by Cub Cadet
LLC with respect to new merchandise purchased and used
in the United States, its possessions and territories.
Cub Cadet LLC warrants this product against defects in
material and workmanship for a period of two (2) years
commencing on the date of original purchase and will, at its
option, repair or replace, free of charge, any part found to
be defective in material or workmanship. This limited
warranty shall only apply if this product has been operated
and maintained in accordance with the Operator’s Manual
furnished with the product, and has not been subject to
misuse, abuse, commercial use, neglect, accident,
improper maintenance, alteration, vandalism, theft, fire,
water or damage because of other peril or natural disaster.
Damage resulting from the installation or use of any
accessory or attachment not approved by Cub Cadet LLC
for use with the product(s) covered by this manual will void
your warranty as to any resulting damage. This warranty is
limited to ninety (90) days from the date of original retail
purchase for any Cub Cadet product that is used for rental
or commercial purposes, or any other income-producing
purpose.
HOW TO OBTAIN SERVICE: Warranty service is
available, WITH PROOF OF PURCHASE THROUGH
YOUR LOCAL AUTHORIZED SERVICE DEALER. To
locate
the dealer in your area, visit our website at
www.cubcadet.com,
check for a listing in the Yellow
Pages, call 1-877-282-8684 or write to
P.O. Box 361131,
Cleveland, OH 44136-0019
.
This limited warranty does not provide coverage in
the following cases:
A. Tune-ups - Spark Plugs, Carburetor Adjustments,
Filters
B. Wear items - Bump Knobs, Outer Spools, Cutting
Line, Inner Reels, Starter Pulley, Starter Ropes, Drive
Belts
C. Cub Cadet LLC does not extend any warranty for
products sold or exported outside of the United
States of America, its possessions and territories,
except those sold through Cub Cadet’s authorized
channels of export distribution.
Cub Cadet LLC reserves the right to change or improve the
design of any Cub Cadet Product without assuming any
obligation to modify any product previously manufactured.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Cub Cadet 41CDC02G100 Le manuel du propriétaire

Catégorie
Coupe-herbe
Taper
Le manuel du propriétaire
Ce manuel convient également à