Cub Cadet CC 2000 Manuel utilisateur

Marque: Cub Cadet

Modèle: CC 2000

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

FORM 769-00023 (11/01) (10700 rev. P00)

Printed in U.S.A.

Operator’s Manual

2-Cycle Trimmer

Model CC 3000

Warning: For users on U.S. Forest Land and in the states of California, Maine, Oregon and Washington. All U.S. Forest Land and the state of

California (Public Resources Codes 4442 and 4443), Oregon and Washington require, by law that certain internal combustion engines operated on

forest brush and/or grass-covered areas be equipped with a spark arrestor, maintained in effective working order, or the engine be constructed,

equipped and maintained for the prevention of fire. Check with your state or local authorities for regulations pertaining to these requirements. Failure

to follow these requirements could subject you to liability or a fine. This unit is factory equipped with a spark arrestor . If it requires replacement,

ask your Cub Cadet dealer dealer to install the Accessory Part #791-181696 Spark Arrestor Kit or contact the service department.

IMPORTANT:READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

Cub Cadet LLC P.O. Box 361131 Cleveland, OH 44136-0019

TABLE OF CONTENTS

Content Page

Section 1: Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Section 2: Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Section 3: Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Section 4: Oil and Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Section 5: Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Section 6: Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Section 7: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Section 8: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Section 9: Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

TO THE OWNER

Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service.

You will find it to be a great labor-saving device. This operator’s manual provides you with easy-to-understand operating

instructions. Before starting or operating this equipment, read the whole manual and follow all the instructions to keep

your new outdoor power tool in top operating condition.

All information, illustrations and specifications in this manual are based on the latest product information available at

the time of printing. We reserve the right to make changes at any time without notice. Service on this unit both within

and after the warranty period should be performed only by a Cub Cadet dealer. Proof of purchase will be required

for warranty service.

FINDING MODEL NUMBER

Before you start assembling your new equipment, please locate the model plate on the equipment and copy the

information from it in the space provided below. This information is important if you need help from your Cub Cadet

dealer.

•You can locate the model number on the shaft housing of the unit next to the On/Off Stop Control Switch.

A sample model plate is explained below. For future reference, please copy the model number and the serial

number of the equipment in the space below below.

Copy the model / parent

part number here:

Copy the serial number here:

CALLING CUSTOMER SUPPORT

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of

this unit, please call the Customer Dealer Referral Line.

Call 1-877-282-8684 to reach the Customer Dealer Referral Line. Please have your unit’s model

number and serial number ready when you call. See previous section to locate this information.

2001 Cub Cadet LLC

For more details about your unit, visit our website at www.cubcadet.com

Section 1

The purpose of safety symbols is to attract your

attention to possible dangers. The safety symbols,

and their explanations, deserve your careful attention

and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper

accident prevention measures.

SYMBOL MEANING

SAFETY ALERT SYMBOL: Indicates

danger, warning, or caution. Attention is

required in order to avoid serious personal

injury. May be used in conjunction with

other symbols or pictographs.

NOTE:Advises you of information or instructions

vital to the operation or maintenance of the

equipment.

Safety

Failure to obey a safety warning will result in

serious injury to yourself or to others. Always

follow the safety precautions to reduce the risk

of fire, electric shock, and personal injury.

Failure to obey a safety warning can result in

injury to yourself and others. Always follow the

safety precautions to reduce the risk of fire,

electric shock, and personal injury.

Failure to obey a safety warning may result in

property damage or personal injury to yourself

or to others. Always follow the safety

precautions to reduce the risk of fire, electric

shock, and personal injury.

• IMPORTANT SAFETY INFORMATION •

•Clear the area to be cut before each use. Remove all

objects such as rocks, broken glass, nails, wire, or

string which can be thrown or become entangled in

the cutting attachment. Clear the area of children,

bystanders, and pets. At a minimum, keep all

children, bystanders and pets outside a 50 feet (15

m) radius; there still may be a risk to bystanders from

thrown objects. Bystanders should wear eye

protection. If you are approached, stop the engine

and cutting attachment immediately.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all

adjustments or repairs before using unit.

• Do not attach or operate this unit with any type of

brushcutting blade or brushcutting attachment as the

unit is currently setup. A brushcutter accessory kit is

available by the manufacturer. See Section 6,

Maintenance for the accessory part number. Use

only the manufacturer’s accessory kit.

SAFETY WARNINGS FOR GAS TRIMMERS

WARNING: Gasoline is highly flammable, and its

vapors can explode if ignited. Take the following

precautions:

• Store fuel only in containers specifically designed

and approved for the storage of such materials.

WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or

emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm.

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill, or under the

influence of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use

the unit, except for teens guided by an adult.

• Inspect the unit before use. Replace damaged parts.

Check for fuel leaks. Make sure all fasteners are in

place and secure. Replace cutting attachment parts

that are cracked, chipped, or damaged in any way.

Make sure the cutting attachment is properly

installed and securely fastened. Be sure the cutting

attachment shield is properly attached, and

positioned as recommended. Failure to so can result

in personal injury to the operator and bystanders, as

well as damage to the unit.

• Use only 0.105 inch (2.67 mm) diameter genuine

manufacturer’s replacement line. Never use metal-

reinforced line, wire, chain, or rope, etc. These can

break off and become a dangerous projectile.

• Be aware of the risk of injury to the head, hands and

feet.

Safety (continued)

• Always stop the engine and allow it to cool before

filling the fuel tank. Never remove the cap of the fuel

tank, or add fuel, when the engine is hot. Never

operate the unit without the fuel cap securely in

place. Loosen the fuel tank cap slowly to relieve any

pressure in the tank.

• Add fuel in a clean, well-ventilated area outdoors

where there are no sparks or flames. Slowly remove

the fuel cap only after stopping engine. Do not

smoke while fueling or mixing fuel. Wipe up any

spilled fuel from the unit immediately.

•Avoid creating a source of ignition for spilled fuel. Do

not start the engine until fuel vapors dissipate.

• Move the unit at least 30 feet (9.1 m) from the fueling

source and site before starting the engine. Do not

smoke, keep sparks and open flames from the area

while adding fuel or operating the unit.

WHILE OPERATING

• Never start or run the unit inside a closed room or

building. Breathing exhaust fumes can kill. Operate

this unit only in a well ventilated area outdoors.

•Wear safety glasses or goggles that are marked as

meeting ANSI Z87.1 standards, and ear/hearing

protection when operating this unit. Wear a face or

dust mask if the operation is dusty.

•Wear heavy, long pants, boots, gloves and a long

sleeve shirt. Do not wear loose clothing, jewelry,

short pants, sandals or go barefoot. Secure hair

above shoulder level.

• The cutting attachment shield must always be in

place while operating the unit. Do not operate unit

without both trimming lines extended, and the proper

line installed. Do not extend the trimming line beyond

the length of the shield.

• This unit has a clutch. The cutting attachment

remains stationary when the engine is idling. If it

does not, have the unit adjusted by an authorized

service technician.

• Adjust the D-Handle to your size to provide the best

grip.

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

•Avoid accidental starting. Be in the starting position

whenever pulling the starter rope. The operator and

unit must be in a stable position while starting. See

Section 5, Operation.

• Use the right tool. Only use this tool for the purpose

intended.

• Do not overreach. Always keep proper footing and

balance.

• Always hold the unit with both hands when

operating. Keep a firm grip on both the front and rear

handle or grips.

• Keep hands, face, and feet at a distance from all

moving parts. Do not touch or try to stop the cutting

attachment when it is rotating.

• Do not touch the engine, gear housing or muffler.

These parts get extremely hot from operation. When

turned off they remain hot for a short time.

• Do not operate the engine faster than the speed

needed to cut, trim or edge. Do not run the engine at

high speed when not cutting.

• Always stop the engine when cutting is delayed or

when walking from one cutting location to another.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Do not operate before repairing damage.

Do not operate the unit with loose or damaged parts.

• Stop and switch the engine to off for maintenance,

repair, or for changing the cutting attachment or

other attachments.

• Use only genuine manufacturer’s replacement parts

and accessories for this unit. These are available

from your authorized service dealer. Use of any parts

or accessories not authorized by the manufacturer

could lead to serious injury to the user, or damage to

the unit, and void your warranty.

• Keep unit clean of vegetation and other materials.

They may become lodged between the cutting

attachment and shield.

•To reduce fire hazard, replace faulty muffler and

spark arrestor, keep the engine and muffler free from

grass, leaves, excessive grease or carbon build up.

OTHER SAFETY WARNINGS

• Never store the unit, with fuel in the tank, inside a

building where fumes may reach an open flame or

spark.

• Allow the engine to cool before storing or transporting.

Be sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high

to prevent unauthorized use or damage, out of the

reach of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean and free from debris.

Clean after each use, see Cleaning and Storage

instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this

unit, also loan them these instructions.

SAVE THESE INSTRUCTIONS

Safety (continued)

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or caution. May be used in conjunction with other

symbols or pictographs.

•WARNING - READ OPERATOR'S MANUAL

Read the Operator’s Manual(s) and follow all warnings and safety instructions.

Failure to do so can result in serious injury to the operator and/or bystanders.

• FOR SERVICE INFORMATION, CALL:

1 (877) 282-8684

• WEAR EYE AND HEARING PROTECTION

WARNING:

Thrown objects and loud noise can cause severe eye injury and hearing

loss. Wear eye protection meeting ANSI Z87.1 standards and ear protection when

operating this unit.

• KEEP BYSTANDERS AWAY

WARNING:

Keep all bystanders, especially children and pets, at least 50 feet (15 m)

from the operating area.

• PRIMER BULB

Push primer bulb, fully and slowly, 5 to 7 times.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• OIL

Refer to operator's manual for the proper type of oil.

• THROWN OBJECTS AND ROTATING CUTTER CAN CAUSE SEVERE INJURY

WARNING:

Do not operate without the cutting attachment shield in place.

Keep away from the rotating cutting attachment.

• ON/OFF STOP CONTROL

ON / START / RUN

• ON/OFF STOP CONTROL

OFF OR STOP

• HOT SURFACE WARNING

Do not touch a hot muffler, gear housing or cylinder. You may get burned. These parts

get extremely hot from operation. When turned off they remain hot for a short time.

SYMBOL MEANING

• SHARP BLADE

WARNING: Sharp blade on cutting attachment shield. To prevent serious injury, do not

touch line cutting blade.

• CHOKE CONTROL

A • START position.

B • RUN position.

WARNING: The operation of any power tool can cause foreign objects to be thrown

into your eyes. This can lead to severe eye damage. Before commencing power tool

operation, always wear safety glasses or goggles that are marked as meeting ANSI

Z87.1 standards, and a full face shield when needed.

THE FOLLOWING ARE FOR REFERENCE WHEN THE UNIT IS ASSEMBLED WITH THE

MANUFACTURER’S BRUSHCUTTER ACCESSORY KIT

Do not attach or operate this unit with any type of brushcutting blade or brushcutting attachment as the

unit is currently setup. A brushcutter accessory kit is available by the manufacturer. See Section 6,

Maintenance for the accessory part number. Use only the manufacturer’s accessory kit. Failure to do so

may result in serious personal injury to yourself or others and/or damage to the unit

• BRUSHCUTTERS • Replace dull blade.

Do not sharpen the cutting blade. Sharpening the blade can cause the blade tip to

break off while in use. This can result in severe personal injury.

• TRIMMER/BRUSHCUTTER SAFETY

WARNING: Thrown objects and rotating cutter can cause severe injury. Keep

bystanders, especially children and pets, at least 50 feet (15 m) away from the cutting

area. The cutting attachment shield must be used when using the trimmer

cutting attachment.

Safety (continued)

Know Your Unit

APPLICATIONS

As a trimmer;

• Cutting grass and weeds.

• Edging

• Decorative trimming around trees, fences, etc.

With the optional brushcutter accessory kit;

• Cutting weeds and light bush of up to 1/2 inch in

diameter.

Shaft Grip

Cutting Attachment Shield

Fuel Cap

Throttle Control

D-Handle

Line Cutting Blade

Cutting Attachment

Primer Bulb

Choke Lever

Gear Housing

Air Filter Cover

Spark Plug

On/Off Stop Control

Shaft Housing

Starter Rope Grip

Support

Fitting

Section 2

Assembly

Section 3

On some units, the D-handle may be preinstalled and

only require loosening the screws and adjusting the

D-handle to the operator. Go to step 4 for adjusting the

D-handle if preinstalled.

INSTALLING AND ADJUSTING THE D-HANDLE

1. Remove the screws, nuts and bottom clamp piece

that were installed on the D-handle for shipping.

2. Place D-handle the over the shaft housing and onto

the bottom clamp (Fig. 3-1). Place it a minimum of

6 inches (15.24 cm) from the end of the shaft grip.

3. Hold each hex nut in the bottom clamp recess with

a finger. Start screws with a screwdriver. Do not

tighten until you make the handle adjustment.

4. If it was preinstalled, loosen the screws on the

D-handle just enough to move the D-handle.

5. While holding the unit in the operating position

(Fig. 3-2), position the D-handle to the location

that provides you the best grip.

6. Tighten the clamp screws evenly, until the D-handle

is secure.

(4) Screws

Shaft

Housing

D-Handle

Bottom Clamp

Fig. 3-1

Fig. 3-2

(4) Nuts

Shaft Grip

Minimum 6 inches

(15.24 cm)

Oil and Fuel

Section 4

Oil and Gas Mixing Instructions

Old and/or improperly mixed fuel are the main

reasons for the unit not running properly. Be sure to

use fresh, clean unleaded fuel. Follow the instructions

carefully for the proper fuel/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and

oxygenates such as ethanol, methanol or MTBE (ether).

Alcohol-blended fuel absorbs water. As little as 1%

water in the fuel can make fuel and oil separate. It

forms acids when stored. When using alcohol-blended

fuel, use fresh fuel (less than 60 days old).

Using Blended Fuels

If you choose to use a blended fuel, or its use is

unavoidable, follow recommended precautions.

• Always use fresh fuel mix per your operator's

manual.

• Always agitate the fuel mix before fueling the unit.

• Drain the tank and run the engine dry before storing

the unit.

Using Fuel Additives

The bottle of Cub Cadet 2-Cycle oil that came with

your unit contains a fuel additive which will help inhibit

corrosion and minimize the formation of gum

deposits.It is recommended that you use only

Cub Cadet 2-Cycle oil with this unit.

If unavailable, use a good 2-cycle oil designed for

air-cooled engines along with a fuel additive, such as

STA-BIL® Gas Stabilizer or an equivalent. Add 0.8 oz.

(23 ml) of fuel additive per gallon of fuel according to

the instructions on the container. NEVER add fuel

additives directly to the unit's fuel tank.

For proper engine operation and maximum

reliability, pay strict attention to the oil and fuel

mixing instructions on the 2-cycle oil container.

Using improperly mixed fuel can severely

damage the engine.

Thoroughly mix the proper ratio of 2-cycle engine oil

with unleaded gasoline in a separate fuel can. Use a

32:1 fuel/oil ratio. Do not mix them directly in the

engine fuel tank. See Figure 4-1 for specific gas and oil

mixing ratios.

NOTE: One gallon (3.8 liters) of unleaded gasoline

mixed with one 4 oz. (118 ml) bottle of Cub Cadet

2-CYCLE OIL makes a 32:1 fuel/oil ratio.

Gasoline is extremely flammable. Ignited Vapors

may explode. Always stop the engine and allow it

to cool before filling the fuel tank. Do not smoke

while filling the tank. Keep sparks and open

flames at a distance from the area.

Remove fuel cap slowly to avoid injury from fuel

spray. Never operate the unit without the fuel cap

securely in place.

Add fuel in a clean, well ventilated area outdoors.

Wipe up any spilled fuel immediately. Avoid

creating a source of ignition for spilt fuel. Do not

start the engine until fuel vapors dissipate.

NOTE: Dispose of the old fuel/oil mix in accordance to

Federal, State, and Local regulations.

UNLEADED GAS Cub Cadet 2 CYCLE OIL

1 US. GALLON

+ 4.0 FL. OZ.

(3.8 LITERS) (118 ml)

MIXING RATIO - 32:1

Fig. 4-1

Operation

Section 5

STARTING INSTRUCTIONS

Operate this unit only in a well ventilated area

outdoors. Carbon monoxide exhaust fumes can

be lethal in a confined area.

Avoid accidental starting. Be in the starting

position whenever pulling the starting rope. To

avoid serious personal injury, the operator and

unit must be in a stable position while starting.

STARTING INSTRUCTIONS

1. Mix gas with oil. Fill fuel tank with fuel/oil mixture.

See Section 4, Oil and Fuel.

2. Put the On/Off Stop Control in the START (I)

position (Fig. 5-1).

3. Fully press and release primer bulb slowly 5 to 7

times. Fuel should be felt and visible in the bulb

(Fig. 5-2). If fuel hasn’t entered the bulb, press

three more times, or until it does.

4. Place the choke lever in the START (A) position

(Fig. 5-2).

5. With the unit on the ground, squeeze the throttle

control and hold. Pull starter rope briskly (Fig. 5-3).

Continue pulling until the engine sounds as though

it wants to run (normally 2 to 5 pulls).

NOTE: Squeeze the throttle control until the engine

has started and warmed up.

6. Place the choke lever in the RUN (B) position

(Fig. 5-2).

7. Pull starter rope briskly 1 to 3 times to start the

engine (Fig. 5-3).

8. If the engine does not start, repeat steps

4 through 7.

NOTE: If the engine floods while trying to start,

place the choke lever in the RUN (B) position.

Squeeze the throttle control. Pull the starter rope

briskly. The engine should start within three (3) to

eight (8) pulls.

9. Squeeze the throttle control to warm up engine for

5 to 10 seconds. Place the choke lever in the RUN

(B) position (Fig. 5-2).

NOTE: Choking is unnecessary when starting a

warm engine. Put the On/Off Stop Control in the

START (I) position (Fig. 5-1), and the choke lever in

the RUN (B) position (Fig. 5-2).

STOPPING INSTRUCTIONS

1. Release your hand from the throttle control

(Fig. 5-3). Allow the engine to idle.

2. To stop the engine, put the On/Off Stop Control in

the STOP [

] position (Fig. 5-1).

Starter Rope

Throttle Control

Primer Bulb

Run (B)

Start (A)

Choke Lever

On/Off Stop Control

Start/

On (I)

Stop/

Off (O)

Fig. 5-1

Fig. 5-2

Fig. 5-3

Operation (continued)

HOLDING THE TRIMMER

Always wear eye, hearing, foot and body

protection to reduce the risk of injury when

operating this unit.

Before operating the unit, stand in the operating

position (Fig. 5-4). Check for the following:

• The operator is wearing eye protection and proper

clothing.

• The right arm is slightly bent, and the hand is

holding the shaft grip.

• The left arm is straight, and the hand is holding the

D-handle.

• The unit is at waist level.

• The cutting attachment is parallel to the ground and

easily contacts the vegetation to be cut without the

operator having to bend over.

ADJUSTING TRIMMING LINE LENGTH

The Bump Head cutting attachment allows you to

release trimming line without stopping the engine. To

release more line, lightly tap the cutting attachment on

the ground (Fig. 5-5) while operating the trimmer at

high speed.

NOTE: Always keep the trimming line fully

extended. Line release becomes more difficult as

cutting line becomes shorter.

Each time the head is bumped, about 1 inch (25.4 mm)

of trimming line is released. A blade in the cutting

attachment shield will cut the line to the proper length

if excess line is released.

For best results, tap the Bump Head on bare ground or

hard soil. If line release is attempted in tall grass, the

engine may stall. Always keep the trimming line fully

extended. Line release becomes more difficult as the

cutting line becomes shorter.

NOTE: Do not rest the Bump Head on the ground

while the unit is running .

Do not remove or alter the line cutting blade

assembly. Excessive line length will make the

clutch overheat. This may lead to serious

personal injury or damage to the unit.

Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• Attempting to cut thick, stalky weeds

• Forcing the line into objects such as walls or fence

posts

TIPS FOR BEST TRIMMING RESULTS

• Keep the cutting attachment parallel to the ground.

• Do not force the cutting attachment. Allow the tip

of the line to do the cutting, especially along walls.

Cutting with more than the tip will reduce cutting

efficiency and may overload the engine.

• Cut grass over 8 inches (200 mm) by working from

top to bottom in small increments to avoid

premature line wear or engine drag.

• Cut from left to right whenever possible. Cutting to

the right improves the unit's cutting efficiency.

Clippings are thrown away from the operator.

• Slowly move the trimmer into and out of the cutting

area at the desired height. Move either in a

forward-backward or side-to-side motion. Cutting

shorter lengths produces the best results.

•Trim only when grass and weeds are dry.

• The life of your cutting line is dependent upon;

• Following the previous trimming techniques

• What vegetation is being cut

• Where it’s being cut

For example, the line will wear faster when trimming

against a foundation wall as opposed to trimming

around a tree.

Fig. 5-4

Fig. 5-5

Operation (continued)

Fig. 5-6

DECORATIVE TRIMMING

Decorative trimming is accomplished by removing all

vegetation around trees, posts, fences, etc.

Rotate the whole unit so that the cutting attachment is

at a 30° angle to the ground (Fig. 5-6).

Section 6

MAINTENANCE

NOTE: Some maintenance procedures may require

special tools or skills. If you are unsure about these

procedures take your unit to an authorized service

dealer.

MAINTENANCE SCHEDULE

These required maintenance procedures should be

performed at the frequency stated in the table. They

should also be included as part of any seasonal tune-

up.

MAINTENANCE NEEDED

Fill fuel tank with correct oil and fuel mixture.

Clean and re-oil air filter.

Check spark arrestor and clean

Check spark plug condition and gap

WHEN

Before Starting Engine

Every 10 Hours

Every 25 Hours

GO TO:

Page 9

Page 15

Page 17

To prevent serious injury, never do maintenance

or repairs with unit running. Always do

maintenance and repairs on a cool unit.

Disconnect spark plug wire to ensure the unit will

not start.

Maintenance (continued)

Slotted

Holes

For Use with Membrane

Line or Single Line

For Use with

Single Line ONLY

Loop

Fig. 6-3

Fig. 6-4

LINE INSTALLATION

This section covers both Membrane line and standard

single line installation.

Always use manufacturer’s 0.105 inch (2.67 mm)

replacement line. Line other than specified may make

the engine overheat or fail.

Never use metal-reinforced line, wire, chain, or

rope, etc. These can break off and become a

dangerous projectile.

There are two methods to replace the trimming line.

• Wind the inner reel with new line

• Install a prewound inner reel

Winding the Existing Inner Reel

1. Hold the outer spool with one hand and unscrew

the Bump Knob clockwise (Fig. 6-1). Inspect the

bolt inside the Bump Knob to make sure it moves

freely. Replace the Bump Knob if damaged.

2. Remove the inner reel from the outer spool

(Fig. 6-1).

3. Remove spring from the inner reel (Fig. 6-1).

4. Use a clean cloth to clean the the inner reel, spring,

shaft, and inner surface of the outer spool.

5. Check the indexing teeth on the inner reel and

outer spool for wear (Fig. 6-2). If necessary, remove

burrs or replace the reel and spool.

NOTE: Membrane line can only be used with the

inner reel with the slotted holes. Single line can be

used on either type of inner reel. Use figure 6-3 to

identify the inner reel you have.

NOTE: Always use the correct line length when

installing trimming line on the unit. The line may

not release properly if the line is too long.

Single Line Installation

Go To Step 8 for Membrane Line Installation

6. Take approximately 30 feet (9.1 m) of new trimming

line, loop it into two equal lengths. Insert each end

of the line through one of the two holes in the inner

reel (Fig. 6-4). Pull the line through the inner reel so

that the loop is as small as possible.

7. Wind the lines in tight even layers, onto the reel

(Fig. 6-5). Wind the line in the direction indicated on

the inner reel. Place your index finger between the

two lines to stop the lines from overlapping. Do not

overlap the ends of the line. Proceed to step 11.

Indexing Teeth

Bump Knob

Bolt

Fig. 6-1

Fig. 6-2

Inner Reel

Spring

Outer Spool

Maintenance (continued)

Membrane Line Installation

8. Take approximately 15 feet (4.6 m) of new trimming

line. Insert one end of the line through one of the

two holes in the inner reel (Fig. 6-6). Pull the line

through the inner reel until only about 4 inches is

left out.

9. Insert the end of the line into the open hole in the

inner reel and pull the line tight to make the loop as

small as possible (Fig. 6-6).

10. Before winding, split the line back about 6 inches.

11. Wind the line in tight even layers in the direction

indicated on the inner reel.

NOTE: Failure to wind the line in the direction

indicated will cause the cutting attachment to

operate incorrectly.

12. Insert the ends of the line into the two holding slots

(Fig. 6-7).

13. Insert the ends of the line through the eyelets in the

outer spool and place inner reel with spring inside

the outer spool (Fig. 6-8). Push the inner reel and

outer spool together. While holding the inner reel

and outer spool, grasp the ends and pull firmly to

release the line from the holding slots in the reel.

NOTE: The spring must be assembled on the inner

reel before reassembling the cutting attachment.

14. Hold the inner reel in place and install the Bump

Knob by turning counterclockwise.

Tighten securely.

INSTALLING A PREWOUND REEL

1. Hold the outer spool with one hand and unscrew

the Bump Knob clockwise (Fig. 6-1). Inspect the

bolt inside the Bump Knob to make sure it moves

freely. Replace the Bump Knob if damaged.

2. Remove the old inner reel from the outer spool

(Fig. 6-1).

3. Remove the spring from the old inner reel

(Fig. 6-1).

4. Place the spring in the new inner reel.

NOTE: The spring must be assembled on the inner

reel before reassembling the cutting attachment.

5. Insert the ends of the line through the eyelets in the

outer spool (Fig. 6-8).

6. Place the new inner reel inside the outer spool.

Push the inner reel and outer spool together. While

holding the inner reel and outer spool, grasp the

ends and pull firmly to release the line from the

holding slots in the spool.

7. Hold the inner reel in place and install the Bump

Knob by turning counterclockwise.

Tighten securely.

Replacement Parts:

See Accessories / Replacement Parts on page 18.

Loop

Holding Slots

Fig. 6-6

Fig. 6-7

Fig. 6-5

Spring

Fig. 6-8

Fig. 6-9

Fig. 6-11

Fig. 6-10

Maintenance (continued)

Carburetor/ Air

Filter Cover

Air Filter

Tab

AIR FILTER MAINTENANCE

Cleaning the Air Filter

To avoid serious personal injury, always turn your

trimmer off and allow it to cool before you clean

or do any maintenance on it.

Clean and re-oil the air filter every 10 hours of

operation. It is an important item to maintain. Not

maintaining the air filter will VOID the warranty.

1. Remove the carburetor/air filter cover by pushing

on the tab on top of the cover (Fig. 6-9).

2. Remove the air filter (Fig. 6-10).

3. Wash the filter in detergent and water. Rinse the

filter thoroughly and allow it to dry.

4. Apply enough clean SAE 30 motor oil to lightly coat

the filter (Fig. 6-11).

5. Squeeze the filter to spread and remove excess oil

(Fig. 6-11).

6. Reinstall the filter (Fig. 6-10) and air filter cover

(Fig. 6-9).

NOTE: If the unit is operated without the air filter,

you will VOID the warranty.

SPARK ARRESTOR MAINTENANCE

To avoid serious personal injury, always turn your

trimmer off and allow it to cool before you clean

or do any maintenance on it.

1. Turn the powerhead so the back of the engine is

facing forward. In this position, the starter rope is to

the left (Fig. 6-12).

Fig. 6-12

Spark

Arrestor

Collar

Maintenance (continued)

Adjust Idle Speed Screw

The cutting attachment may be spinning during

idle speed adjustment. Wear protective clothing

and observe all safety instructions to prevent

serious personal injury.

If after checking the fuel mixture and cleaning the air

filter the engine still will not idle, adjust the idle speed

screw as follows.

1. Start the engine and let it run at a high idle for a

minute to warm up.

2. Release the throttle trigger and let the engine idle. If

the engine stops, insert a small phillips or flat blade

screwdriver into the screw next to the air filter

cover (Fig. 6-14). Turn the idle speed screw in,

clockwise, 1/8 of a turn at a time (as needed) until

the engine idles smoothly.

NOTE: The cutting attachment should not rotate

when the engine idles.

3. If the cutting attachment rotates when the engine

idles, turn the idle speed screw counterclockwise

1/8 of a turn at a time (as needed), to reduce idle

speed.

Checking the fuel mixture, cleaning the air filter, and

adjusting the idle speed screw should solve most

engine problems.

If not and:

• The engine will not idle,

• The engine hesitates or stalls on acceleration,

• There is a loss of engine power,

have the carburetor adjusted by an

authorized service dealer.

Fig. 6-14

Idle Speed Screw

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable by the screw

next to the air filter cover (Fig 6-14).

NOTE: Careless adjustments can seriously damage

your unit. An authorized service dealer should make

carburetor adjustments.

Check Fuel Mixture

Old and/or improperly mixed fuel is usually the reason

for the unit not running properly. Drain and refill the tank

with fresh, properly mixed fuel prior to making any

adjustments. See Section 5, Oil and Fuel.

Clean Air Filter

The condition of the air filter is important to the

operation of the unit. A dirty air filter will restrict air flow

and change the air/fuel mixture. This is often mistaken

for an out of adjustment carburetor. Check the

condition of the air filter before adjusting the idle speed

screw. See Section 6, Maintenance.

2. Use a needlenose pliers to grasp the collar of the

spark arrestor and pull it out of the muffler (Fig. 6-13).

NOTE: Use only a needlenose pliers. Other pliers or

tools may damage the spark arrestor.

3. Clean the spark arrestor with a wire brush. Replace

if damaged or unable to clean thoroughly.

4. Reinstall spark arrestor. Use the needlenose pliers

to gently push the spark arrestor back into the

muffler until it snaps into place.

Fig. 6-13

Maintenance (continued)

CLEANING

To avoid serious personal injury, always turn your

trimmer off and allow it to cool before you clean

or do any maintenance on it.

Use a small brush to clean off the outside of the unit.

Do not use strong detergents. Household cleaners that

contain aromatic oils such as pine and lemon, and

such as kerosene, can damage plastic housing or

handle. Wipe off any moisture with a soft cloth.

STORAGE

• Never store the unit with gasoline in the tank where

fumes may reach an open flame or spark.

• Allow the engine to cool before storing.

• Store the unit locked up to prevent unauthorized use

or damage.

• Store the unit in a dry, well ventilated area.

• Store the unit out of the reach of children.

LONG TERM STORAGE

If the unit will be stored for an extended time,

1. Drain all fuel from the gas tank into a container. Do

not use fuel that has been stored for more than 60

days. Dispose of the old fuel in accordance to

Federal, State, and Local regulations.

2. Start the engine and allow it to run until it stalls.

This ensures that all gasoline has been drained

from the carburetor.

3. Allow the engine to cool. Remove the spark plug

and put 1 oz. (30 ml) of high quality motor oil into

the cylinder. Pull the starter rope slowly to

distribute the oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the

oil from the cylinder before attempting to start the

trimmer after storage.

4. Thoroughly clean the unit and inspect for any loose

or damaged parts. Repair or replace damaged

parts and tighten loose screws, nuts or bolts. The

unit is ready for storage.

TRANSPORTING

• Allow the engine to cool before transporting.

• Secure the unit while transporting.

• Drain the gas tank before transporting.

• Tighten gas cap before transporting.

REPLACING THE SPARK PLUG

Use a Champion RCJ6Y spark plug (or equivalent). The

correct air gap is 0.025 inch (0.655 mm). Remove the

plug after every 25 hours of operation and check its

condition.

1. Stop the engine and allow it to cool. Grasp the plug

wire firmly and pull the cap from the spark plug.

2. Clean dirt from around the spark plug. Remove the

spark plug from the cylinder head by turning a 5/8

inch socket counterclockwise.

3. Replace cracked, fouled or dirty spark plug. Set the

air gap at 0.025 inch (0.655 mm) using a feeler

gauge (Fig. 6-15).

Do not sand blast, scrape, or clean electrodes.

Grit in the engine could damage the cylinder.

4. Install a correctly gaped spark plug in the cylinder

head. Tighten by turning the 5/8 inch socket

clockwise until snug.

If using a torque wrench torque to:

110-120 in.•lb. (12.3-13.5 N•m).

Do not over tighten.

0.025 inch

(0.655 mm)

Fig. 6-15

ACCESSORIES/REPLACEMENT PARTS

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 791-181765

Spark Arrestor . . . . . . . . . . . . . . . . . . . . . . . . . . . 791-181696

Replacement Line Cartridge . . . . . . . . . . . . . . . . . . . 153-1160

Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . . 791-610636

Bump Head Knob Assembly . . . . . . . . . . . . . . . . . 791-180814

Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 791-180000

Brushcutter Accessory Kit . . . . . . . . . . . . . . . . 41AM079G100

Shoulder Harness . . . . . . . . . . . . . . . . . . . . . . . . . 791-682075

Tip-and-Pour 2-Cycle Oil (16 oz.) . . . . . . . . . . . . . .791-180965

These replacement parts can be purchased at the

retailer from which you bought your trimmer, or your

local Cub Cadet dealer.

Troubleshooting

Section 7

CAUSE ACTION

Cutting attachment bound with grass Stop the engine and clean cutting attachment

Cutting attachment out of line Refill with new line

Inner reel bound up Replace the inner reel

Cutting head dirty Clean inner reel and outer spool

Line welded Disassemble, remove the welded section

and rewind the line

Line twisted when refilled Disassemble and rewind the line

Not enough line is exposed Push the Bump Knob and pull out line until

4 inches (102 mm) of line is outside of the

cutting attachment

CAUSE ACTION

Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture

Improper carburetor adjustment Take to an authorized service dealer for

carburetor adjustment

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

CAUSE ACTION

On/Off Stop Control is in STOP position Turn On/Off Stop Control to START

Empty fuel tank Fill fuel tank with properly mixed fuel

Primer bulb wasn't pressed enough Press primer bulb fully and slowly 5-7 times

Engine flooded Use starting procedure with choke lever in the

RUN position, Pg. 11

Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

ENGINE WILL NOT START

ENGINE WILL NOT IDLE

ENGINE WILL NOT ACCELERATE

ENGINE LACKS POWER OR STALLS WHEN CUTTING

CAUSE ACTION

Air Filter is Plugged Replace or clean the air filter

Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture

Improper carburetor adjustment Adjust per instruction Pg. 16

CAUSE ACTION

Old or improperly mixed fuel Drain gas tank / Add fresh fuel mixture

Improper carburetor adjustment Take to an authorized service dealer for

carburetor adjustment

Cutting attachment bound with grass Stop the engine and clean the cutting attachment

Dirty air filter Clean or replace the air filter

Plugged spark arrestor Clean or replace spark arrestor

CUTTING ATTACHMENT WILL NOT ADVANCE LINE

Specifications

Section 8

Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-Cooled, 2-Cycle

Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 cu. in. (25cc)

Clutch Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Centrifugal

Idle Speed RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,400-3,600 rpm

Operating RPM (Trimmer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,000-8,600 rpm

Ignition Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronic

On/Off Stop Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Toggle Switch

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel/Oil Mixture

Fuel/Oil Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32:1

Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unleaded

Carburetor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diaphragm, All-Position

Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auto Rewind

Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Baffled with Guard

Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual Spring Return

Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 oz (591 ml)

ENGINE

DRIVE SHAFT & CUTTING ATTACHMENT

Drive Shaft Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aluminum Tube

Throttle Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Finger-Tip Trigger

Unit Weight (No Fuel, with D-handle, Cutting attachment shield and Cutting attachment) . . . . . . . . . . . . 11 lbs (4.9 kg)

Cutting Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dual String Cutting Head

Line Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bump Line Releaser

Line Spool Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 inches (101.6 mm)

Trimming Line Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.105 inches (2.67 mm)

Cutting Path Diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 inches (44.0 cm)

MANUFACTURER’S LIMITED WARRANTY FOR:

Cub Cadet LLC reserves the right to change or improve

the design of any Cub Cadet Product without assuming

any obligation to modify any product previously

manufactured.

No implied warranty, including any implied warranty of

merchantability or fitness for a particular purpose,

applies after the applicable period of express written

warranty above as to the parts as identified. No other

express warranty or guaranty, whether written or oral,

except as mentioned above, given by any person or

entity, including a dealer or retailer, with respect to any

product shall bind Cub Cadet LLC During the period of

the Warranty, the exclusive remedy is repair or

replacement of the product as set forth above. (Some

states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to

you.)

The provisions as set forth in this Warranty provide the

sole and exclusive remedy arising from the sales. Cub

Cadet LLC shall not be liable for incidental or

consequential loss or damages including, without

limitation, expenses incurred for substitute or

replacement lawn care services, for transportation or

for related expenses, or for rental expenses to

temporarily replace a warranted product. (Some states

do not allow limitations on how long an implied warranty

lasts, so the above limitation may not apply to you.)

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold.

Alteration of the safety features of the product shall void

this Warranty. You assume the risk and liability for loss,

damage, or injury to you and your property and/or to

others and their property arising out of the use or misuse

or inability to use the product.

This limited warranty shall not extend to anyone other than

the original purchaser, original lessee or the person for

whom it was purchased as a gift.

How State Law Relates to this Warranty: This warranty

gives you specific legal rights, and you may also have

other rights which vary from state to state.

To locate your nearest service dealer dial

1 (877) 282-8684 .

Cub Cadet LLC

P.O. Box 361131

Cleveland, OH 44136-0019

The limited warranty set forth below is given by Cub Cadet

LLC with respect to new merchandise purchased and

used in the United States, its possessions and territories.

Cub Cadet LLC warrants this product against defects in

material and workmanship for a period of two (2) years

commencing on the date of original purchase and will, at

its option, repair or replace, free of charge, any part found

to be defective in material or workmanship. This limited

warranty shall only apply if this product has been operated

and maintained in accordance with the Operator’s Manual

furnished with the product, and has not been subject to

misuse, abuse, commercial use, neglect, accident,

improper maintenance, alteration, vandalism, theft, fire,

water or damage because of other peril or natural disaster.

Damage resulting from the installation or use of any

accessory or attachment not approved by Cub Cadet LLC

for use with the product(s) covered by this manual will void

your warranty as to any resulting damage. This warranty is

limited to ninety (90) days from the date of original retail

purchase for any Cub Cadet product that is used for rental

or commercial purposes, or any other income-producing

purpose.

HOW TO OBTAIN SERVICE: Warranty service is

available, WITH PROOF OF PURCHASE THROUGH

YOUR LOCAL AUTHORIZED SERVICE DEALER. To locate

the dealer in your area, visit our website at

www.cubcadet.com, check for a listing in the Yellow

Pages, call 1 (877) 282-8684 or write to

P.O. Box 361131,

Cleveland, OH 44136-9722

This limited warranty does not provide coverage in

the following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments,

Filters

B. Wear items - Bump Knobs, Outer Spools, Cutting

Line, Inner Reels, Starter Pulley,Starter Ropes, Drive

Belts

C. Cub Cadet LLC does not extend any warranty for

products sold or exported outside of the United

States of America, its possessions and territories,

except those sold through Cub Cadet’s authorized

channels of export distribution.

La page charge ...

Cub Cadet CC 2000 Manuel utilisateur

Marque: Cub Cadet

Modèle: CC 2000

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Cub Cadet CC 2000 User manual
español: Cub Cadet CC 2000 Manual de usuario

Documents connexes

Autres documents

Powermate PWSTM4317EA Manuel utilisateur