Wacker Neuson LTN6K-V Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur

Ce manuel convient également à

5200004276 02 0714
Operator’s Manual
Light Tower
LTN 6K-V, LTN 6K-VS
LTN 8K-V, LTN 8K-VS
Notice d’Emploi
Tour d’éclairage
EN/FR
5200004276
Copyright
notice
© Copyright 2014 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the machine. Any
other type of reproduction is prohibited without express written permission from
Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker Neuson Production
Americas LLC represents an infringement of valid copyrights. Violators will be
prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original
instructions
This Operator’s Manual presents the original instructions. The original language of this
Operator’s Manual is American English.
5200004276 02 0714
LTN 6K / 8K-V Foreword
wc_tx003092gb.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machines
covered in
this manual
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
Use the separate Parts Book supplied with the machine to order replacement
parts.
If you are missing either of these documents, please contact Wacker Neuson to
order a replacement or visit www.wackerneuson.com.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and main-
tain the above Wacker Neuson model(s). For your own safety and to reduce the
risk of injury, carefully read, understand, and observe all instructions described
in this manual.
Machine Item Number
LTN 6K-V 5200002722, 5200002726
LTN 8K-V 5200002727, 5200002728
LTN 6K-V S 5200018537, 5200018550, 5200018553
LTN 8K-V S 5200018538, 5200018551, 5200018554
wc_gr010093
Serial Number:
Foreword LTN 6K / 8K-V
4 wc_tx003092gb.fm
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change
any portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
Manufacturers
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker Neu-
son service center according to written instructions published by Wacker Neu-
son.
Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following
consequences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
CALIFORNIA
Proposition
65 Warning
Combustion exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-
charge of sparks or flames from the engine exhaust. Spark arresters are qualified
and rated by the United States Forest Service for this purpose. In order to comply
with local laws regarding spark arresters, consult the engine distributor or the local
Health and Safety Administrator.
Table of Contents
LTN 6K / 8K-V
wc_bo5200004275_02TOC.fm
5
Foreword 3
1 Safety Information 9
1.1 Signal Words Used in this Manual ....................................................... 9
1.2 Machine Description and Intended Use ............................................. 10
1.3 Safety Guidelines for Operating the Machine ..................................... 11
1.4 Service Safety .................................................................................... 14
1.5 Operator Safety while Using Internal Combustion Engines ............... 16
1.6 Safety Guidelines for Lifting and Transporting the Machine ............... 17
1.7 Safety Guidelines for Towing the Machine ......................................... 18
1.8 Reporting Safety Defects ................................................................... 19
2 Labels 20
2.1 Label Locations .................................................................................. 20
2.2 Label Meanings .................................................................................. 22
3 Lifting and Transporting 31
3.1 Lifting the Machine ............................................................................. 31
3.2 Preparing the Machine for Transport on a Truck or Trailer ................ 32
3.3 Preparing the Machine for Towing ..................................................... 33
3.4 Towing the Machine ........................................................................... 34
4 Operation 35
4.1 Preparing the Machine for First Use ................................................... 35
4.2 Generator Derating ............................................................................. 35
4.3 Positioning the Machine ..................................................................... 36
4.4 Ground Connection ............................................................................ 37
4.5 Leveling Trailer ................................................................................... 38
4.6 Refueling the Machine ........................................................................ 39
4.7 Aiming the Lights - LTN-V .................................................................. 40
4.8 Control Panels .................................................................................... 43
4.9 Before Starting ................................................................................... 44
4.10 Starting the Machine .......................................................................... 45
4.11 Operating the Lights ........................................................................... 46
4.12 Raising the Tower - LTN 6L-V ............................................................ 47
4.13 Manually Rotating the Mast ................................................................ 48
4.14 Lowering the Tower ............................................................................ 49
4.15 Automatic Shutdown .......................................................................... 50
Table of Contents
LTN 6K / 8K-V
wc_bo5200004275_02TOC.fm
6
4.16 Stopping the Machine ..........................................................................50
4.17 Emergency Shutdown Procedure ........................................................51
4.18 Using the Convenience Receptacles - 60 Hz ......................................52
5 Maintenance 53
5.1 Preparing for Maintenance ..................................................................53
5.2 Periodic Maintenance Schedule ..........................................................54
5.3 Cleaning the Machine ..........................................................................55
5.4 Inspecting the Machine .......................................................................56
5.5 Checking the Engine Oil ......................................................................57
5.6 Changing the Engine Oil .....................................................................58
5.7 Checking the Engine Coolant Level ....................................................59
5.8 Flushing the Radiator ..........................................................................60
5.9 Cleaning the Air Filter Element ............................................................62
5.10 Maintaining the Battery ........................................................................63
5.11 Checking Fan Belt Tension .................................................................64
5.12 Checking Radiator Hoses ....................................................................65
5.13 Performing Coolant Solution Analysis .................................................66
5.14 Testing the Cooling System Pressure .................................................67
5.15 Removing and Replacing Lamps ........................................................69
5.16 Long-Term Storage .............................................................................71
5.17 Machine Disposal / Decommissioning .................................................72
6 Maintenance Tier 4f Engines: Kubota 74
7 Troubleshooting 78
8 Technical Data 80
8.1 Engine .................................................................................................80
8.2 Generator ............................................................................................81
8.3 Machine ...............................................................................................82
8.4 Radiation Compliance .........................................................................83
8.5 Dimensions - LTN 6K-V, LTN 8K-V .....................................................83
8.6 Dimensions - LTN 6K-VS, LTN 8K-VS ................................................83
9 Schematics 84
9.1 LTN 8K-V Lighting Schematic .............................................................84
9.2 Components ........................................................................................85
Table of Contents
LTN 6K / 8K-V
wc_bo5200004275_02TOC.fm
7
9.3 LTN 6K-V Lighting Schematic ............................................................ 86
9.4 Components ....................................................................................... 87
9.5 Generator Capacitor Excitation Schematic ........................................ 88
9.6 Engine Wiring ..................................................................................... 89
9.7 Components ....................................................................................... 90
9.8 Hydraulic Schematic - LTN 6K-V, LTN 8K-V ...................................... 91
9.9 Hydraulic Schematic- LTN 6K-VS, LTN 8K-VS .................................. 92
9.10 Trailer Wiring ...................................................................................... 93
Table of Contents
LTN 6K / 8K-V
wc_bo5200004275_02TOC.fm
8
wc_si000704gb.fm
9
LTN 6K / 8K-V Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
f Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
f To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
f To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
f To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si000704gb.fm
10
Safety Information LTN 6K / 8K-V
1.2 Machine Description and Intended Use
Machine
description
This machine is a mobile, trailer-mounted light tower. The Wacker Neuson Light
Tower consists of a trailer with a cabinet containing a diesel engine, a fuel tank, a
control panel, and an electric alternator. A telescoping tower with four metal halide
lights is vertically mounted to the top of the machine. A hydraulic cylinder,
combined with a cable and pulley system, raises and lowers the telescoping tower.
As the engine runs, the generator converts mechanical energy into electric power.
The metal halide lights run off this power. Receptacle(s) are also provided to power
auxiliary loads. The operator uses the control panel to operate and monitor the
machine.
Intended use
This machine is intended for the illumination of outdoor areas. This machine is also
intended for the purpose of supplying electrical power to connected loads. Refer to
the machine specifications for the output voltage and frequency, and for the
maximum output power limit of this Light Tower.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty. The following are some
examples of misuse:
Connecting a load that has voltage and frequency requirements that are
incompatible with the machine output
Overloading the machine with a device that draws excessive power during
either continuous running or startup
Operating the machine in a manner that is inconsistent with all federal, state,
and local codes and regulations
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Using the machine as a hoist, or hanging items from the tower
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, exhaust, and carbon monoxide from the engine
Heat from the lights
Ultraviolet radiation from the lights
Fire hazards from improper refueling techniques
Fuel and its fumes
Electric shock and arc flash
Personal injury from improper lifting the trailer tongue
wc_si000704gb.fm
11
LTN 6K / 8K-V Safety Information
Glare from lights (lights may blind drivers of nearby motor vehicles if the lights
are incorrectly positioned)
Typical hazards related to towing a trailer on roads and highways
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
1.3 Safety Guidelines for Operating the Machine
Operator
training
Before operating the machine:
Read and understand the operating instructions contained in all manuals
delivered with the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Contact Wacker Neuson for additional training if necessary.
When operating this machine:
Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
have received instruction on how to properly use the machine
are familiar with required safety devices
The machine must not be accessed or operated by:
children
people impaired by alcohol or drugs
Application
area
Be aware of the application area.
Keep unauthorized personnel, children, and pets away from the machine.
Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
Be aware of the application area.
Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
Safety
devices,
controls, and
attachments
Only operate the machine when:
All safety devices and guards are in place and in working order.
All controls operate correctly.
The machine is set up correctly according to the instructions in the Operator’s
Manual.
The machine is clean.
The machine’s labels are legible.
To ensure safe operation of the machine:
wc_si000704gb.fm
12
Safety Information LTN 6K / 8K-V
Do not operate the machine if any safety devices or guards are missing or
inoperative.
Do not modify or defeat the safety devices.
Only use accessories or attachments that are approved by Wacker Neuson.
Safe
operating
practices
When operating this machine:
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
When operating this machine:
Do not operate a machine in need of repair.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while operating this
machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
Before
Starting
Be sure the machine is on a firm, level surface and will not tip, roll, slide, or fall
while operating.
Never connect machine to other power sources, such as supply mains of power
companies.
Never use the machine if the insulation on the electrical cord is cut or worn
through.
Never raise the tower or operate the machine in high winds.
The tower extends up to 8.7 m (28.54 ft.). Make sure the area above the trailer
is open and clear of overhead wires and obstructions.
Operation
Keep the area under and around the lights clear of people while raising and
lowering the tower.
Do not move the Light Tower while it is operating.
After Use
Stop the engine when the machine is not being operated.
Close the fuel valve on engines equipped with one when machine is not being
operated.
Ensure that the machine will not tip over, roll, slide, or fall when not being
operated.
Store the machine properly when it is not being used. The machine should be
stored in a clean, dry location out of the reach of children.
Lower the tower when not in use, or if high winds or electrical storms are
expected in the area.
The lamps become extremely hot in use! Allow the lamp and fixture to cool
10–15 minutes before handling.
Lamp Safety
wc_si000704gb.fm
13
LTN 6K / 8K-V Safety Information
Description
The lamps provided with your Light Tower are electric discharge lamps. They are
designed for use with metal halide ballasts only, and require time to reach full
brightness on initial startup and after a power interruption. These lamps comply
with FDA regulation performance standards 21 CFR 1040-30.
Operating
safety
Replace damaged lamps according to the instructions in section Removing /
Replacing Lamps.
Alternative lamps that automatically extinguish when the outer envelope is
broken or punctured are commercially available.
WARNING
Personal injury hazard. Broken or punctured lamps can cause serious skin burns
and eye inflammation from shortwave ultraviolet radiation.
" Do not operate the Light Tower if a lamp is damaged.
f Replace damaged lamps immediately.
wc_si000704gb.fm
14
Safety Information LTN 6K / 8K-V
1.4 Service Safety
Service
training
Before servicing or maintaining the machine:
Read and understand the instructions contained in all manuals delivered with
the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Only trained personnel shall troubleshoot or repair problems occurring with the
machine.
Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
Do not allow improperly trained people to service or maintain the machine.
Personnel servicing or maintaining the machine must be familiar with the
associated potential risks and hazards.
Precautions
Follow the precautions below when servicing or maintaining the machine.
Read and understand the service procedures before performing any service to
the machine.
All adjustments and repairs must be completed before operating the machine.
Do not operate the machine with a known problem or deficiency.
All repairs and adjustments shall be completed by a qualified technician.
Turn off the machine before performing maintenance or making repairs.
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
Re-install the safety devices and guards after repair and maintenance
procedures are complete.
Machine
modifications
When servicing or maintaining the machine:
Use only accessories/attachments that are approved by Wacker Neuson.
When servicing or maintaining the machine:
Do not defeat safety devices.
Do not modify the machine without the express written approval of Wacker
Neuson.
Replacing
parts and
labels
Replace worn or damaged components.
Replace all missing and hard-to-read labels.
When replacing electrical components, use components that are identical in
rating and performance to the original components.
When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.
wc_si000704gb.fm
15
LTN 6K / 8K-V Safety Information
Cleaning
When cleaning and servicing the machine:
Keep the machine clean and free of debris such as leaves, paper, cartons, etc.
Keep the labels legible.
When cleaning the machine:
Do not clean the machine while it is running.
Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while servicing or
maintaining this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair.
Remove all jewelry (including rings).
Before servicing the Light Tower, make sure the engine start switch is turned to
the OFF position, the circuit breakers are open (off), and the negative terminal
on battery is disconnected. Do not perform even routine service (oil/filter
changes, cleaning, etc.) unless all electrical components are shut down.
Always turn off light circuit breakers and shut down engine before disconnecting
light fixtures or changing light bulbs.
wc_si000704gb.fm
16
Safety Information LTN 6K / 8K-V
1.5 Operator Safety while Using Internal Combustion Engines
Operating
safety
When running the engine:
Keep the area around exhaust pipe free of flammable materials.
Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine. Do not run the machine if fuel leaks are present or the fuel lines are
loose.
When running the engine:
Do not smoke while operating the machine.
Do not run the engine near sparks or open flames.
Do not touch the engine or muffler while the engine is running or immediately
after it has been turned off.
Do not operate a machine when its fuel cap is loose or missing.
Do not start the engine if fuel has spilled or a fuel odor is present. Move the
machine away from the spill and wipe the machine dry before starting.
Refueling
safety
When refueling the engine:
Clean up any spilled fuel immediately.
Refill the fuel tank in a well-ventilated area.
Replace the fuel tank cap after refueling.
Use suitable tools for refueling (for example, a fuel hose or funnel).
When refueling the engine:
Do not smoke.
Do not refuel a hot or running engine.
Do not refuel the engine near sparks or open flames.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
f Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Exhaust gas from the engine contains carbon monoxide, a deadly poison.
Exposure to carbon monoxide can kill you in minutes.
f NEVER operate the machine inside an enclosed area, such as a tunnel, unless
adequate ventilation is provided through such items as exhaust fans or hoses.
wc_si000704gb.fm
17
LTN 6K / 8K-V Safety Information
1.6 Safety Guidelines for Lifting and Transporting the Machine
When lifting the machine:
Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any
other type of lifting device used is attached securely and has enough weight-
bearing capacity to lift or hold the machine safely. See section Technical Data
for machine weight.
Remain aware of the location of other people when lifting the machine.
Only use the lifting points and tie-downs described in the Operators Manual.
Make sure the transporting vehicle has sufficient load capacity and platform size
to safely transport the machine.
To reduce the possibility of injury:
Do not stand under the machine while it is being lifted or moved.
Do not get onto the machine while it is being lifted or moved.
wc_si000704gb.fm
18
Safety Information LTN 6K / 8K-V
1.7 Safety Guidelines for Towing the Machine
When towing the machine:
Do not tow the machine if the towing vehicle’s hitch or the trailer’s coupler are
damaged.
Do not tow the machine if any of the trailer’s lug nuts are missing.
Do not tow the machine if the trailer’s tires have less than 1.5 mm (1/16 inch) of
tread.
Do not tow the machine unless the trailer’s brakes are functioning properly.
Do not exceed the trailer manufacturer’s speed limitations.
When towing the machine:
Only tow the machine when the trailer’s lug nuts are properly torqued.
Only tow the machine when the trailer’s tires are properly inflated.
Only tow the machine when all trailer lights are functioning correctly.
Only tow the machine when the trailer’s safety chains are connected to the
towing vehicle in a crisscross pattern.
Maintain extra distance between the towing vehicle and other vehicles.
Avoid soft shoulders, curbs, and sudden lane changes.
Abide by all licensing requirements for your area.
If you have not driven a towing vehicle with trailer before, practice turning,
stopping, and backing up the towing vehicle with trailer in an area away from traffic.
Only drive the towing vehicle with trailer when you are confident in your ability to do
so.
WARNING
Risk of severe injury or death. Improper trailer condition and towing technique can
lead to an accident.
f Obey the trailer manufacturer’s instructions and the instructions below to reduce
the risk of an accident.
wc_si000704gb.fm
19
LTN 6K / 8K-V Safety Information
1.8 Reporting Safety Defects
If you believe your trailer has a defect which could cause a crash or could cause
injury or death, you should immediately inform the National Highway Traffic Safety
Administration (NHTSA) in addition to notifying Wacker Neuson.
If NHTSA receives similar complaints, it may open an investigation; and if it finds
that a safety defect exists in a group of trailers, it may order a recall and remedy
campaign. However, NHTSA cannot become involved in individual problems
between you, your dealer, or Wacker Neuson.
To contact NHTSA, you may either contact the Vehicle Safety Hotline toll-free at
1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to:
Administrator
NHTSA
1200 New Jersey Avenue S.E.
Washington, DC 20590
You can also obtain other information about your motor vehicle safety from
http://www.safercar.gov
Labels LTN 6K / 8K-V
20 wc_si000705gb.fm
2 Labels
2.1 Label Locations
wc_gr009301
A
B
R
C
C
C
S
WH
H
X
Y
D
E
F
G
HIJK
L
Q
P
O
N
M
1 / 1

Wacker Neuson LTN6K-V Manuel utilisateur

Catégorie
Groupes électrogènes
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues