LG 1289201 Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire
OWNER'S MANUAL
WASHING MACHINE
Read this owner's manual thoroughly before operating the
appliance and keep it handy for reference at all times.
ENGLISH ESPAÑOL FRANÇAIS
WM4500H*A
MFL71485411
Rev.01_061020
www.lg.com
Copyright © 2020 LG Electronics Inc. All Rights Reserved.
TABLE OF CONTENTS
2
3 IMPORTANT SAFETY
INSTRUCTIONS
3 READ ALL INSTRUCTIONS BEFORE USE
3 WARNING STATEMENTS
5 CAUTION STATEMENTS
7 PRODUCT OVERVIEW
7 Product Features
9 INSTALLATION
9 Before Installing
10 Choosing the Proper Location
11 Unpacking and Removing Shipping Material
12 Connecting the Water Inlet Hoses
13 Connecting the Drain Hose
14 Leveling the Washer
15 Final Installation Check
17 OPERATION
17 Before Use
18 Sorting Laundry
19 Loading the Washer
20 Adding Cleaning Products
23 Control Panel
25 Wash Cycles
29 Cycle Modifiers
29 Options and Extra Functions
33 SMART FUNCTIONS
33 Using LG ThinQ Application
35 Smart Diagnosis
TM
Function
37 MAINTENANCE
37 Regular Cleaning
37 Periodic Maintenance
41 Care in Cold Climates
43 TROUBLESHOOTING
43 Before Calling for Service
53 LIMITED WARRANTY
53 USA
56 CANADA
3IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Safety Messages
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
follow all safety messages.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,
and tell you what may happen if the instructions are not followed.
WARNING STATEMENTS
WARNING
To reduce the risk of explosion, fire, death, electric shock, scalding or injury to persons when using this
product, follow basic precautions, including the following:
Installation
Adhere to all industry recommended safety procedures including the use of long-sleeved gloves and
safety glasses.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has
missing or broken parts, including a damaged cord or plug.
Before use, the appliance must be properly installed as described in this manual.
To reduce the risk of severe injury or death, follow all installation instructions.
Refer to the INSTALLATION INSTRUCTIONS for detailed grounding procedures. Installation instructions
are packed with the appliance for the installer’s reference. If the appliance is moved to a new location,
have it checked and reinstalled by qualified service personnel.
Moving or installation of the appliance requires two or more people.
Do not install the appliance in humid spaces.
Store and install the appliance where it will not be exposed to temperatures below freezing or exposed
to outdoor weather conditions.
This appliance is not designed for maritime use or for mobile installations such as in RVs, trailers, or
aircraft.
Keep packing materials out of the reach of children. Packaging material can be dangerous for children.
There is a risk of suffocation.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages
will follow the safety alert symbol and either the word WARNING or CAUTION.
These words mean:
WARNING
You may be killed or seriously injured if you do not follow instructions.
CAUTION
You may be injured or cause damage to the product if you do not follow instructions.
4 IMPORTANT SAFETY INSTRUCTIONS
Destroy the carton, plastic bag, and other packing materials after the appliance is unpacked. Children
might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight
chambers.
The appliance must be installed and electrically grounded by qualified service personnel in accordance
with local codes.
When installing or moving the appliance, be careful not to pinch, crush, or damage the power cord.
Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.
This appliance must be positioned near to an electrical power supply.
Disconnect the power cord, house fuse or circuit breaker before installing or servicing the appliance.
The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock from this appliance.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
Use new hoses when connecting the washer to the water supply. Do not reuse old hoses.
Operation
Read all instructions before using the appliance and save these instructions.
Use this appliance only for its intended purpose.
If the product has been submerged in water, sitting in standing water, or waterlogged, do not come in
contact with the product and immediately contact an LG Electronics Customer Information Center for
instructions before resuming use.
If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance, unplug
it immediately, and contact an LG Electronics Customer Information Center.
Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used
for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water system has not been used for
such a period, before using the appliance, turn on all hot water faucets and let the water flow from each
for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not
smoke or use an open flame during this time.
Do not reach into the washer if the tub or drum, agitator, or any interior parts are moving. Before
loading, unloading, or adding items, press Start/Pause and allow the tub or drum to coast to a complete
stop before reaching inside.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a person responsible for their safety.
Do not allow children or pets to play on, in or with the appliance. Close supervision is necessary when the
appliance is used near children or pets.
Keep laundry products out of children’s reach. To prevent injury to persons, observe all warnings on
product labels.
Repair or immediately replace all power cords that have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage along its length or at either end.
Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight
out from the outlet.
Do not use an extension cord or adapter with this appliance.
Do not grasp the power cord or touch the appliance controls with wet hands.
Do not modify or extend the power cord.
If the electrical supply cord is damaged, it must only be replaced by the manufacturer or its service agent
or a similar qualified person in order to avoid a hazard.
Do not put oily or greasy clothing, candles or flammable materials on top of the appliance.
Keep the area underneath and around your appliances free of combustible materials (lint, paper, rags,
etc.), gasoline, chemicals and other flammable vapors and liquids.
5IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
Do not mix chlorine bleach with ammonia or acids such as vinegar. Follow package directions when
using laundry products. Incorrect usage can produce poisonous gas, resulting in serious injury or death.
Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage the
finish.
Do not wash laundry that has been previously cleaned in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, vegetable or cooking oil, or other flammable or explosive substances, as they give
off vapors that could ignite or explode.
Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash
water. These substances give off vapors that could ignite or explode.
In the event of a gas leak (propane gas, LP gas, etc.), do not operate this or any other appliance. Open a
window or door to ventilate the area immediately.
Do not tamper with controls.
Fix the drain hose securely in place to avoid flooding.
Do not abuse, sit on, or stand on the door of the appliance.
Always check the inside of the appliance for foreign objects.
Do not allow water, bleach or other liquids to sit in the drum for extended periods. Doing so can corrode
the drum or cause mildew or odors.
Maintenance
Do not repair or replace any part of the appliance. All repairs and servicing must be performed by
qualified service personnel unless specifically recommended in this owner’s manual. Use only authorized
factory parts.
Disconnect this appliance from the power supply before cleaning and attempting any user maintenance.
Turning the controls to the OFF position does not disconnect this appliance from the power supply.
Remove any dust or foreign matter from the power plug pins.
Do not disassemble or repair the appliance by yourself.
Remove the door before the appliance is removed from service or discarded to avoid the danger of
children or small animals getting trapped inside.
Make sure the dispenser drawer or lid is closed at all times when not being filled with laundry products.
Grounding Instructions
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check
with a qualified electrician or service personnel if you are in doubt whether the appliance is properly
grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
The appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the
risk of electric shock by providing a path of least resistance for electric current. The appliance is
equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes
and ordinances.
CAUTION STATEMENTS
CAUTION
To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or
property when using this product, follow basic precautions, including the following:
6 IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Installation
Install the product on a firm and level floor.
Operation
Do not place objects on top of the appliance.
Turn off the water faucets and unplug the appliance if the appliance is to be left for an extended period
of time, such as during vacations.
ALWAYS follow the fabric care instructions supplied by the garment manufacturer.
Use fabric softeners or products to eliminate static only as recommended by the manufacturer.
Do not combine laundry products for use in one load unless specified on the label.
Do not touch draining water which may be hot.
If the drain hose and the water inlet hose are frozen in winter, defrost them before using the appliance.
Do not store or spill liquid detergents, cleaners, or bleaches (chlorine bleach, oxygen bleach) on the
appliance. Doing so may result in corrosion, discoloration or damage to the surface of the appliance.
Clothing or articles that are waterproof or water resistant must be washed in the Waterproof cycle only.
(Examples include water resistant clothing, mattress covers, outdoor clothes, plastic mats.) Using
another cycle may result in personal injury or damage to the washer, clothes, walls, floor, and
surrounding objects due to abnormal vibration.
7PRODUCT OVERVIEW
ENGLISH
PRODUCT OVERVIEW
Product Features
The images in this guide may be different from the actual components and accessories, which are subject
to change by the manufacturer without prior notice for product improvement purposes.
WARNING
For your safety and for extended product life, use only authorized components. The manufacturer is not
responsible for product malfunction, property damage or bodily injury caused by the use of separately
purchased unauthorized components, parts, or non-LG products.
Front View
a Control Panel
b Detergent Dispenser Drawer (ezDispense/
Manual Dispense)
c Door
d Drain Pump Filter
e Drain Hose
f Drain Pump Filter Cover
g Leveling Feet
h Door Seal
i Drum
Rear View
a Water Inlets
b Shipping Bolts
c Power Cord
d Drain Hose
8 PRODUCT OVERVIEW
Accessories
Included Accessories
a
Non-skid Pads
b Hole Caps
c Wrench
d Tie Strap
e Elbow Bracket (for securing drain hose)
Required Accessories
a
Hot and Cold Water Hoses
Optional Accessories
a
Pedestal
b Pedestal Washer
c Stacking Kit
Product Specifications
Model WM4500H*A
Electrical
Requirements
120 VAC @ 60 Hz
Min. / Max. Water
Pressure
20 - 120 psi (138 - 827
kPa)
Dimensions (Width X
Height X Depth)
27'' X 39" X 33 1/4''' (70
cm X 99 cm X 84 cm)
Maximum Depth with
Door Open
53 1/4'' (135.5 cm)
Net Weight 201.5 lb (91.4 kg)
Max. Spin Speed 1300 RPM
9INSTALLATION
ENGLISH
INSTALLATION
Before Installing
Installation Overview
Please read the following installation instructions first after purchasing this washer or transporting it to
another location.
a Choosing the Proper Location
b Unpacking and Removing Shipping Material
c Connecting the Inlet Hoses
d Connecting the Drain Hose
e Leveling the Washer
f Final Installation Check
WARNING
Moving or installation of the appliance requires two or more people. Failure to follow these instructions
may result in injury.
Store and install the appliance where it will not be exposed to temperatures below freezing or exposed
to outdoor weather conditions. Failure to follow this warning can cause product or part failure, serious
injury, fire, electric shock, or death.
Properly ground the washer to conform with all governing codes and ordinances. Failure to follow this
warning can cause serious injury, fire, electric shock, or death.
To ensure proper airflow, do not block the large opening on the bottom of the washer with carpeting or
other materials.
Do not remove the ground prong from the power cord. Do not use an adapter or extension cord. Plug
into a grounded 3-prong outlet. Failure to follow this warning can cause serious injury, fire, electric
shock, or death.
abc
ef
10 INSTALLATION
WARNING
Certain internal parts are intentionally not grounded and may present a risk of electric shock only during
servicing. Service personnel- Do not contact the following parts while the appliance is energized: pump,
valve, motor, control board.
Tools Needed
a Pliers
b Flat-Blade Screwdriver
c Level
Choosing the Proper
Location
Check the following requirements for the install
location before installing the washer.
Allow for sufficient space between the walls and
the washer for installation.
Make sure that the floor is clean, dry and free of
dust, dirt, water and oil so the leveling feet
cannot slide easily. Leveling feet that can move
or slide on the floor can contribute to excess
vibration and noise.
If the floor has too much flex, reinforce it to
make it more rigid. If the floor is not solid, it may
cause severe vibration and noise.
If a drain pan must be used, take extra care to
follow the instructions provided with the drain
pan and make sure the leveling feet are adjusted
for firm and even contact with the pan. Use of
drain pans and failure to properly level the
washer may result in increased vibration and
noise during operation.
Power Outlet
The power outlet must be within 60 inches (1.5
m) of either side of the washer.
Position the washer so that the outlet and plug
are easily accessible.
Do not overload the outlet with more than one
appliance.
The outlet must be grounded in accordance with
current electrical wiring codes and regulations.
Use a time-delay fuse or circuit breaker.
It is the personal responsibility and obligation of
the washer owner to have a proper outlet
installed by a qualified electrician.
Flooring
To minimize noise and vibration, install the
washer on a level, solidly constructed floor
capable of supporting the washer without
flexing or bouncing.
The washer must be installed on firm flooring to
minimize vibration during the spin cycle.
Concrete flooring is best, but a wood floor is
sufficient, provided it is built to FHA standards.
The floor under the washer must not slope more
than 1 inch (2.5 cm) from front to back or side to
side.
Installing on carpeting and soft tile surfaces is
not recommended.
Never install the washer on a platform or weakly
supported structure.
Floor Installation
To ensure sufficient clearance for water inlet
hoses, drain hose and airflow, allow minimum
clearances of at least 1 inch (2.5 cm) at the sides
and 4 inches (10 cm) behind the washer. Be sure
to allow for wall, door, or floor moldings that may
increase the required clearances.
Dimensions and Clearances
A 20'' (51.5 cm)
B 53 1/4'' (135.5 cm)
C 33 1/4'' (84 cm)
D 4'' (10 cm)
A
B
C
D
E
E
F
G
11INSTALLATION
ENGLISH
Stacking or Pedestal Installation
The washer can be stacked under a dryer or on top
of a pedestal or pedestal washer.
NOTE
Refer to the instructions packaged with the
optional pedestal kit before stacking appliance
on pedestal.
Do not use a drain pan with a pedestal or
pedestal washer installation as it can block the
drawer. Using a drain pan may result in
increased vibration and noise during operation.
Unpacking and Removing
Shipping Material
Remove all shipping materials from the washer for
proper operation and inspect it for shipping
damage.
CAUTION
Failure to remove shipping materials can cause
excessive noise and vibration.
Unpacking Shipping Material
* This feature is only available on some models.
Lift the washer off the foam base.
After removing the carton and shipping
material, lift the washer off the foam base.
Make sure the plastic drum support
a* comes
off with the base and is not stuck to the bottom
of the washer.
If you must lay the washer down to remove the
carton base
b, always protect the side of the
washer and lay it carefully on its side. Do not lay
the washer on its front or back.
Removing Shipping Material
1 Remove the bolt assemblies.
Starting with the bottom two shipping bolts
c , use the included wrench to fully loosen
all 4 shipping bolts by turning them
counterclockwise.
Remove the bolt assemblies (bolts and
retainers) by wiggling them slightly while
pulling them out.
2 Install the hole caps.
Locate the hole caps d included in the
accessory pack or attached to the back of
E1'' (2.5 cm)
F 27'' (70 cm)
G1/4'' (0.5 cm)
Dimensions and Clearances
A 33 1/4" (84 cm)
B 4'' (10 cm)
C1'' (0.5 cm)
D 27'' (70 cm)
E 77 1/2'' (196.8 cm)
F1/4'' (0.5 cm)
Dimensions and Clearances
ABCCD
E
F
*
12 INSTALLATION
the washer. Install the caps in the holes left
by the bolt assemblies.
CAUTION
Once removed, save the bolt assemblies for
future use. To prevent damage to internal
components, do not transport the washer
without reinstalling the shipping bolts. Failure to
remove shipping bolts and retainers may cause
severe vibration and noise, which can lead to
permanent damage to the washer.
NOTE
The power cord is secured to the back of the
washer with a shipping bolt to help prevent
operation with shipping bolts in place.
Connecting the Water Inlet
Hoses
To avoid the risk of costly water damage, purchase
and install new water inlet hoses when installing
the washer.
WARNING
Do not overtighten the hoses or cross-thread the
hose fittings. Overtightening or cross-threading
can damage the valves or couplings, resulting in
leaking and property damage.
Do not reuse old hoses. Use only new hoses
when installing the washer. Old hoses could leak
or burst causing flooding and property damage.
Contact an LG Customer Information Center for
assistance in buying hoses.
NOTE
Periodically check the hoses for cracks, leaks,
and wear, and replace the hoses every five years.
Do not stretch the water hoses intentionally, and
make sure that they are not pinched, crushed or
kinked by other objects.
Water supply pressure must be between 20 psi
and 120 psi (138 - 827 kPa). If the water supply
pressure is more than 120 psi, a pressure
reducing valve must be installed.
Your hot water heater should be set to deliver
water at 120–135 °F (48–57 °C) to allow the
washer to properly control wash temperatures.
Do not store or install the washer in a location
subject to freezing temperatures. Damage to the
water inlet hoses and internal mechanisms of
the washer can result. If the washer was
exposed to freezing temperatures prior to
installation, allow it to stand at room
temperature for several hours before use and
check for leaks prior to operation.
Do not use flood-preventing hoses with auto
shut off devices. The devices can be tripped
during fill and prevent the washer from filling
properly.
How to Connect the Water Inlet
Hoses
1 Check the fittings and seals. Inspect the
threaded fitting on each hose and make sure
there is a rubber seal a in place in both ends
of each hose to prevent leaking.
2 Connect the water supply hoses.
Connect the water inlet hoses to the hot
and cold water faucets tightly by hand and
then tighten another 2/3 turn with pliers.
Connect the blue hose to the cold water
faucet and the red hose to the hot water
faucet.
3 Flush out the inlet hoses.
After the hoses are connected, turn on the
water faucets and flush out any foreign
substances such as dirt, sand, or sawdust.
13INSTALLATION
ENGLISH
Let the water drain into a bucket, and check
the water temperature to make sure you’ve
connected the hoses to the correct faucets.
4 Attach the inlet hoses to the back of the
washer.
Attach the hot water inlet hose to the hot
water inlet on the back of the washer.
Attach the cold water inlet hose to the cold
water inlet on the back of the washer.
Tighten the fittings securely. Turn on both
faucets all the way and check for leaks at
both ends of the hoses.
Connecting the Drain Hose
Connect the drain hose to either a standpipe or
laundry tub.
WARNING
The drain hose should always be properly
secured. Failure to properly secure the drain
hose can result in flooding and property
damage.
NOTE
The drain must be installed in accordance with
any applicable local codes and regulations.
Make sure that the drain hose is not stretched,
pinched, crushed, or kinked.
Do not install the drain hose with the end lower
than 29.5 inches (75 cm) or higher than 96
inches (244 cm) above the bottom of the washer
or more than 60 inches (152 cm) away from the
washer.
Never create an airtight seal between the hose
and the drain with tape or other means. If no air
gap is present, water can be siphoned out of the
drum resulting in poor wash/rinse performance
or clothing damage.
Using a Standpipe to Drain
1 Clip the end of the hose into the elbow
bracket.
Connect the elbow bracket a within 4
inches (10 cm) of the end of the drain hose.
If the drain hose is extended more than 4
inches (10 cm) beyond the end of the elbow
bracket, mold or microorganisms could
spread to the inside of the washer.
2 Insert the end of the drain hose into the
standpipe.
3 Use the provided tie strap b to secure the
drain hose in place.
4 If the water valves and drain are built into the
wall, fasten the drain hose to one of the water
hoses with the provided tie strap
c (ribbed
side on inside).
4 "
(10 cm)
14 INSTALLATION
Using the Laundry Tub to Drain
1 Clip the end of the hose into the elbow
bracket.
Connect the elbow bracket a within 4
inches (10 cm) of the end of the drain hose.
If the drain hose is extended more than 4
inches (10 cm) beyond the end of the elbow
bracket, mold or microorganisms could
spread to the inside of the washer.
2 Hang the end of the drain hose over the side
of the laundry tub.
3 Use the provided tie strap to secure the drain
hose in place.
Leveling the Washer
The drum of the washer spins at very high speeds.
To minimize vibration, noise, and unwanted
movement, the floor must be a solid, level surface.
CAUTION
Using the washer without leveling it may cause
excess vibration and noise, leading to a washer
malfunction.
Adjust the leveling feet only as far as necessary
to level the washer. Extending the leveling feet
more than necessary can cause the washer to
vibrate.
NOTE
Before installing the washer, make sure that the
floor is clean, dry and free of dust, dirt, water
and oil so the washer feet cannot slide easily.
Feet that move or slide on the floor can
contribute to excessive vibration and noise.
How to Level the Washer
1 Position the washer in its final location.
Take special care not to pinch, strain, or
crush the water and drain hoses. If you have
a carpenter’s level
a, you can use it to
check that the washer is level. The slope
beneath the washer should not exceed 1
inch, and all 4 leveling feet must rest firmly
on the floor.
2 Adjust the leveling feet.
Turn all 4 leveling feet in one direction to
raise the washer or the other direction to
lower it.
29.5 - 96 "
(75 - 244 cm)
29.5 - 96 "
(75 - 244 cm)
4 "
(10 cm)
15INSTALLATION
ENGLISH
3 Check the level again.
Push or rock the top edges of the washer
gently to make sure the washer does not
rock. If the washer rocks, readjust the
leveling feet.
4 Tighten the locknuts b
Turn the locknuts counterclockwise and
tighten them when the washer is level.
Using Non-Skid Pads
If you install the washer on a slippery surface, it
may move because of excessive vibration.
Incorrect leveling may cause malfunction through
noise and vibration. If this occurs, install the non-
skid pads under the leveling feet and adjust the
level.
1 Clean the floor to attach the non-skid pads.
Use a dry rag to remove and clean foreign
objects or moisture. If moisture remains,
the non-skid pads may slip.
2 Adjust the level after placing the washer in the
installation area.
3 Place the adhesive side c of the non-skid pad
on the floor.
It is most effective to install the non-skid
pads under the front leveling feet. If it is
hard to place the pads under the front
leveling feet, place them under the back
leveling feet.
a This side up
b Remove backing
4 Recheck the washer’s levelness.
Push or rock the top edges of the washer
gently to make sure the washer does not
rock. If the washer rocks, level the washer
again.
Final Installation Check
Connecting to the Power Supply
Plug the washer into a 120 VAC, 60 Hz grounded 3-
prong outlet.
WARNING
Do not use a worn or damaged power cord or
power plug. Replace or repair it immediately.
Failure to do so may result in death, fire, electric
shock, or malfunction.
Do not modify the power cord and plug provided
with the appliance. Do not damage it when
installing or moving the appliance. Doing so may
result in death, fire, electric shock, or
malfunction.
Make sure that the appliance is grounded.
Connect this appliance to a grounded outlet
conforming to the rating prior to use. Failure to
do so may result in fire, electric shock, or
malfunction.
Do not damage or cut off the ground prong of
the power cord. Doing so may cause death, fire,
electric shock, or product malfunction.
Improper connection of the equipment
grounding conductor can result in risk of electric
shock. Check with a qualified electrician or
service technician if you are in doubt as to
whether the appliance is properly grounded. If
the plug does not fit the outlet, have a proper
outlet installed by a qualified electrician.
The appliance and outlet must be positioned so
that the plug is easily accessible.
Do not use an adapter or extension cord. Doing
so may result in serious injury, fire, electric
shock, or death.
For best performance, plug the appliance into its
own individual outlet. This helps prevent
overloading house wiring circuits which could
cause a fire hazard from overheated wires.
If necessary, use a new, UL-listed 3-prong
(grounding) plug rated at no less than the
branch circuit. Do not use an extension cord
longer than 3 feet. Failure to follow these
warnings may result in serious injury, fire,
electric shock, or death.
16 INSTALLATION
Testing the Washer
Check if the washer is properly installed and run a
test cycle.
1 Load the washer with 6 thick bath towels
(approximately 6 pounds).
2 Press the Power button.
3 Press the Rinse+Spin button.
4 Press the Start/Pause button to start the
wash cycle.
5 Make sure that water is supplied, that the
washer does not rock or vibrate excessively,
and that it drains well during the spin cycle.
NOTE
If water leaks during water supply, see
Connecting the Water Inlet Hoses to connect
them properly.
If the washer rocks and vibrates excessively, see
Leveling the Washer to level it again.
If the drain does not work, see Connecting the
Drain Hose to install the hose properly.
17OPERATION
ENGLISH
OPERATION
Before Use
WARNING
To reduce the risk of fire, electric shock, or injury to persons, read the SAFETY INSTRUCTIONS before
operating this appliance.
Operation Overview
1 Sort laundry and load the washer.
Sort laundry by fabric type, soil level, color and load size, as needed. Open the door and load items
into the washer.
If using single-use detergent packs, place pack into the drum before loading the laundry.
2 Add cleaning products.
Fill the larger ezDispense reservoir with HE (High-Efficiency) liquid detergent. Fill the smaller
reservoir with liquid fabric softener, if desired.
Use the front detergent compartment of the manual dispenser for liquid or powdered detergent, or
oxygen-based bleach. Place liquid chlorine bleach ONLY in the bleach compartment at the back of
the manual dispenser.
3 Turn on the washer.
Press the Power button to turn on the washer.
4 Select a cycle.
Turn the cycle selector knob or press the cycle buttons repeatedly until the desired cycle is selected.
The preset wash temperature, spin speed, soil level and option settings for the selected cycle are
shown.
•The Normal cycle must be selected in order to change its default settings.
Pressing the Start/Pause button without selecting a cycle immediately starts the Normal cycle with
the default settings.
5 Adjust settings.
Default settings for the selected cycle can be changed, if desired, using the cycle modifier and
option buttons.
Not all modifiers and options are available on all cycles. A different chime sounds and the LED does
not light up if the selection is not allowed.
6 Begin cycle.
Press the Start/Pause button to begin the cycle. The door locks, and the washer agitates briefly
without water to measure the weight of the load.
•If the Start/Pause button is not pressed within a certain time, the washer shuts off and all settings
are lost.
18 OPERATION
7 End of cycle.
When the cycle is finished, a melody sounds. Immediately remove the clothing from the washer to
reduce wrinkling.
Check around the door seal when removing the load for small items that may be caught in the seal.
NOTE
The washer rotates the laundry in a way that allows it to use less water while still fully saturating the
clothing. It is normal to be unable to see water during the wash cycle.
If the temperature or the water level inside the machine is too high, the door will not unlock when the
Start/Pause button is pressed, and the Add Item function will not be available (on applicable models).
To stop a cycle and drain the water completely, turn the power off, then on, and then select Rinse+Spin.
Sorting Laundry
CAUTION
Clothing or articles that are waterproof or water-resistant must be washed in the Waterproof, Bedding,
Bulky/Large, or Jumbo Wash cycle only. (Examples include water resistant clothing, mattress covers,
outdoor clothes, and plastic mats.) Failure to do so may result in personal injury or damage to the
washer, clothes, walls, floor, and surrounding objects due to abnormal vibration.
Remove the stuffing from pillows and cushions before washing the covers. Failure to do so can cause
excessive vibration, resulting in damage to the washer, clothes, nearby objects, walls, and floor.
Grouping Similar Items
For the best washing results, and to reduce the possibility of damage to clothing, sort clothing into loads
made up of similar items.
Mixing different fabric types and/or soil levels can result in poor wash performance, color transfer,
discoloration, fabric damage or linting. Fabrics should be sorted into groups as described below.
Colors
Sort articles by color. Wash dark clothes separately from light colors or whites. Mixing dark clothes with
light clothes can result in dye transfer or discoloration of the lighter clothes.
Soil Level
Wash heavily soiled clothing together. Washing lightly soiled clothing in the same load with heavily soiled
clothing could result in poor wash performance for the lightly soiled clothing.
Fabric Type
Delicate articles should not be mixed with heavy or sturdy fabric types. Washing heavy fabrics with
delicates can result in poor wash performance for the heavy fabrics and possible damage to the delicates.
Lint Type
Some fabrics attract and bind lint to them while others give off lint in the laundry process. Avoid mixing
these lint collectors and lint producers in the same load. Mixing these fabrics will result in pilling and
linting on the lint collectors. (For example, lint collector - knit sweater; lint producer - terry cloth towels.)
How to Sort Laundry
By Colors By Soil By Fabric By Lint
White Heavy Delicates Lint Producer
19OPERATION
ENGLISH
Fabric Care Labels
Many articles of clothing include a fabric care label. Using the chart below, adjust the cycle and option
selections to care for your clothing according to the manufacturer’s recommendations.
Loading the Washer
CAUTION
Clothing or articles that are waterproof or water-
resistant must be washed in the Waterproof,
Bedding, Bulky/Large, or Jumbo Wash cycle
only. (Examples include water resistant clothing,
mattress covers, outdoor clothes, and plastic
mats.) Failure to do so may result in personal
injury or damage to the washer, clothes, walls,
floor, and surrounding objects due to abnormal
vibration.
General Tips
Check and empty pockets. Paper clips, coins,
matches, etc.can damage clothing and the
washer.
Close zippers and hooks, and tie drawstrings to
prevent snagging or tangling of clothes.
Pretreat heavily stained areas for best results.
Brush off heavy soil, dust, and hair from items
before washing. Excess dirt or sand can abrade
other fabrics and lead to poor wash
performance.
For best performance, load clothes as shown.
- Do not press down on items while stacking
them in the drum.
- Load clothes loosely, and do not overfill the
drum. Clothes need room to circulate in order
to get clean.
Lights Normal Easy Care Lint Collector
Darks Light Sturdy
Category Label Directions
Washing
Hand wash
Machine wash, Normal cycle
Perm Press/Wrinkle Resistant setting (which has a cool down or cold
spray before the slower spin)
Gentle/Delicate setting (slow agitation and/or reduced wash time)
Do not wash
Do not wring
Water Temperature
Hot
Warm
Cold/Cool
Bleach Symbols
Any bleach (when needed)
Only non-chlorine bleach (when needed)
Do not bleach
By Colors By Soil By Fabric By Lint
1
3
2
4
20 OPERATION
Combine large and small items in the drum.
Load large items first. Large items should not be
more than half of total load.
The washer can be fully loaded, but the drum
should not be tightly packed with items. The
door of the washer must close easily.
The washer will not fill or operate with the door
open.
Bulky Items
Wash thick, bulky items individually. Heavy
blankets, comforters, bed spreads, or pet beds
can get tangled or cause an unbalanced load if
combined with other items.
Small Items
Do not wash a single small item. Add enough
similar items to the load to prevent an out-of-
balance load.
Wash small, light items in a mesh bag. Small
items can get caught in the impeller at the
bottom of the drum, and brassiere hooks can
snag on other clothing or the drum.
Waterproof Items
Do not wash/spin waterproof items. Washing
raincoats or sleeping bags may result in
abnormal vibration or may cause the load to
bounce, which could damage the drum.
Adding Cleaning Products
About Detergent Use
This washer is designed for use with only HE (High-
Efficiency) detergents.
HE detergents produce fewer suds, dissolve
more efficiently to improve washing and rinsing
performance, and help to keep the interior of
the washer clean. Using detergent that is not HE
may cause oversudsing and unsatisfactory
performance which could result in error codes,
cycle failure, and washer damage.
Detergents designated as HE-compatible may
not provide optimal results.
For proper wash performance, always measure
detergent using the measuring device provided
by the detergent manufacturer. For an average
load, use less than half of the recommended
maximum. Use less detergent for soft water,
light soil, or smaller loads.
Use extra care when measuring 2X and 3X
concentrated detergents because even a small
amount of extra detergent can lead to problems.
Never use more than the maximum amount of
detergent recommended by the manufacturer.
Using too much detergent can lead to
oversudsing, poor rinsing, detergent buildup in
clothing, and residue buildup that can contribute
to odors in the washer.
Do not use more than one single-use detergent
pack in the washer. Using too much detergent
may cause oversudsing and unsatisfactory
performance. Reduce detergent amount or add
an extra rinse if detergent residue is left on
fabrics. To add an extra rinse, select the Extra
Rinse option.
a Maximum fill line
b Average load fill line
c Liquid detergent
d Powdered detergent
Single-Use Detergent Packs
Place liquid or powdered detergent packs in the
drum before loading laundry. Do not place
detergent packs in the dispenser.
Using the ezDispense Function
When the ezDispense function is turned on, the
liquid detergent and softener are dispensed in the
set amounts, at the appropriate time during the
cycle.
A full detergent reservoir will last for about 18
standard cycles, with the drum filled about
halfway.
The default settings are configured to dispense
1.5 oz (45 ml) of detergent and 1 oz (30 ml) of
softener for 8-12 lb (4-6 kg) of normally soiled
laundry. This can be changed using the
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188

LG 1289201 Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire

dans d''autres langues