Makita XRH10Z-DC18RD Manuel utilisateur

Marque: Makita

Modèle: XRH10Z-DC18RD

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

Cordless Combination Hammer

Martillo Rotativo Combinado

Inalámbrico

XRH08

XRH10

XRH11

IMPORTANT: Read Before Using.

IMPORTANTE: Lea antes de usar.

2 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: XRH08 XRH10 XRH11

Capacities Concrete 28 mm (1-1/8")

Core bit 54 mm (2-1/8")

Diamond core bit (dry type) 65 mm (2-9/16")

Steel 13 mm (1/2")

Wood 32 mm (1-1/4")

No load speed 0 - 980/min

Blows per minute 0 - 5,000/min

Overall length 373 mm (14-3/4") 404 mm (15-7/8")

Rated voltage D.C. 36 V

Net weight 3.9 - 5.1 kg (8.6 - 11.2 lbs)

Optional accessory

Model: DX03 (For XRH08/XRH10) DX04 (For XRH11)

Suction performance 350 l/min

Operating stroke Up to 190 mm (7-1/2")

Suitable drill bit Up to 260 mm (10-1/4")

Rated voltage D.C. 18 V

Net weight 1.4 kg (3.2 lbs) 1.5 kg (3.2 lbs)

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsandbatterycartridgemaydifferfromcountrytocountry.

• Theweightmaydifferdependingontheattachment(s),includingthebatterycartridge.Thelightestandheavi-

estcombination,accordingtoEPTA-Procedure01/2014,areshowninthetable.

Applicable battery cartridge

BL1815N / BL1820B / BL1830 / BL1830B / BL1840B / BL1850B / BL1860B

• Someofthebatterycartridgeslistedabovemaynotbeavailabledependingonyourregionofresidence.

WARNING: Only use the battery cartridges listed above. Use of any other battery cartridges may cause

injuryand/orre.

SAFETY WARNINGS

General power tool safety warnings

WARNING:

Read all safety warnings, instruc-

tions, illustrations and specications provided with this

power tool. Failure to follow all instructions listed below

mayresultinelectricshock,reand/orseriousinjury.

Save all warnings and instruc-

tions for future reference.

Theterm"powertool"inthewarningsreferstoyour

mains-operated(corded)powertoolorBATTERY-

operated (cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical Safety

1. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiedplugsandmatchingoutletswill

reduce risk of electric shock.

2. Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.Thereisanincreasedriskofelec-

tric shock if your body is earthed or grounded.

3. Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase

the risk of electric shock.

3 ENGLISH

4. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled cords

increase the risk of electric shock.

5. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

6. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit inter-

rupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electric shock.

7. Power tools can produce electromagnetic

elds (EMF) that are not harmful to the user.

However, users of pacemakers and other similar

medical devices should contact the maker of their

device and/or doctor for advice before operating

this power tool.

Personal Safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inuence of drugs, alcohol or med-

ication.Amomentofinattentionwhileoperating

powertoolsmayresultinseriouspersonalinjury.

2. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

willreducepersonalinjuries.

3. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or BATTERY pack, pick-

ing up or carrying the tool. Carrying power tools

withyourngerontheswitchorenergisingpower

tools that have the switch on invites accidents.

4. Remove any adjusting key or wrench before

turning the power tool on.Awrenchorakeyleft

attached to a rotating part of the power tool may

resultinpersonalinjury.

5. Do not overreach. Keep proper footing and

balance at all times.Thisenablesbettercontrol

of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.Looseclothes,jewel-

lery or long hair can be caught in moving parts.

7. If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

8. Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles.Acarelessaction

cancausesevereinjurywithinafractionofa

second.

9. Always wear protective goggles to protect

your eyes from injury when using power tools.

The goggles must comply with ANSI Z87.1 in

the USA.

It is an employer's responsibility to enforce

the use of appropriate safety protective equip-

ments by the tool operators and by other per-

sons in the immediate working area.

Power tool use and care

1. Do not force the power tool. Use the correct

power tool for your application.Thecorrect

powertoolwilldothejobbetterandsaferatthe

rate for which it was designed.

2. Do not use the power tool if the switch does

not turn it on and off.Anypowertoolthatcannot

be controlled with the switch is dangerous and

must be repaired.

Disconnect the plug from the power source and/

or remove the BATTERY pack, if detachable,

from the power tool before making any adjust

ments, changing accessories, or storing power

tools. Such preventive safety measures reduce the

risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in the

hands of untrained users.

5. Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may affect the power tool’s operation. If dam-

aged, have the power tool repaired before use.

Many accidents are caused by poorly maintained

power tools.

6. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

7. Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power tool

for operations different from those intended could

result in a hazardous situation.

8. Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for

safe handling and control of the tool in unexpected

situations.

9. When using the tool, do not wear cloth work

gloves which may be entangled.Theentangle-

ment of cloth work gloves in the moving parts may

resultinpersonalinjury.

BATTERY tool use and care

1. Recharge only with the charger specied by

the manufacturer.Achargerthatissuitablefor

onetypeofBATTERYpackmaycreateariskof

rewhenusedwithanotherBATTERYpack.

Use power tools only with specically des-

ignated BATTERY packs. Use of any other

BATTERYpacksmaycreateariskofinjuryandre.

When BATTERY pack is not in use, keep it

away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from one

terminal to another.ShortingtheBATTERYtermi-

nalstogethermaycauseburnsorare.

4. Under abusive conditions, liquid may be

ejected from the BATTERY; avoid contact. If

contact accidentally occurs, ush with water.

If liquid contacts eyes, additionally seek med-

ical help.LiquidejectedfromtheBATTERYmay

cause irritation or burns.

4 ENGLISH

5. Do not use a BATTERY pack or tool that is

damaged or modied.Damagedormodied

batteries may exhibit unpredictable behaviour

resultinginre,EXPLOSIONorriskofinjury.

6. Do not expose a BATTERY pack or tool to re

or excessive temperature.Exposuretoreor

temperature above 130 °C may cause explosion.

7. Follow all charging instructions and do not

charge the BATTERY pack or tool outside the

temperature range specied in the instruc-

tions. Charging improperly or at temperatures

outsidethespeciedrangemaydamagethe

BATTERYandincreasetheriskofre.

Service

1. Have your power tool serviced by a qualied

repair person using only identical replacement

parts.Thiswillensurethatthesafetyofthepower

tool is maintained.

Never service damaged BATTERY packs. Service

ofBATTERYpacksshouldonlybeperformedbythe

manufacturer or authorized service providers.

3. Follow instruction for lubricating and chang-

ing accessories.

4. Do not modify or attempt to repair the appli-

ance or the BATTERY pack except as indicated

in the instructions for use and care.

CORDLESS ROTARY HAMMER

SAFETY WARNINGS

1. Wear ear protectors. Exposure to noise can

cause hearing loss.

2. Use auxiliary handle(s), if supplied with the

tool.Lossofcontrolcancausepersonalinjury.

Hold power tool by insulated gripping sur-

faces, when performing an operation where the

cutting accessory may contact hidden wiring.

Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

Wear a hard hat (safety helmet), safety glasses and/

or face shield. Ordinary eye or sun glasses are NOT

safety glasses. It is also highly recommended that

you wear a dust mask and thickly padded gloves.

5. Be sure the bit is secured in place before

operation.

Under normal operation, the tool is designed to

produce vibration. The screws can come loose

easily, causing a breakdown or accident. Check

tightness of screws carefully before operation.

7. In cold weather or when the tool has not been

used for a long time, let the tool warm up for

a while by operating it under no load. This

will loosen up the lubrication. Without proper

warm-up, hammering operation is difcult.

Always be sure you have a rm footing. Be sure no

one is below when using the tool in high locations.

9. Hold the tool rmly with both hands.

10. Keep hands away from moving parts.

11. Do not leave the tool running. Operate the tool

only when hand-held.

12. Do not point the tool at any one in the area

when operating. The bit could y out and

injure someone seriously.

13.

Do not touch the bit, parts close to the bit, or

workpiece immediately after operation; they

may be extremely hot and could burn your skin.

14. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material supplier

safety data.

15.

Always be sure that the tool is switched off and

the battery cartridge and the bit are removed

before handing the tool to other person.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

Symbols

Thefollowingsshowthesymbolsusedfortool.

volts

direct current

no load speed

revolutions or reciprocation per minute

number of blow

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

5 ENGLISH

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tapeormaskoffopencontactsandpackupthe

battery in such a manner that it cannot move

around in the packaging.

11. Follow your local regulations relating to dis-

posal of battery.

12. Use the batteries only with the products

specied by Makita. Installing the batteries to

non-compliantproductsmayresultinare,exces-

sive heat, explosion, or leak of electrolyte.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causingres,personalinjuryanddamage.Itwill

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. Charge the battery cartridge if you do not use

it for a long period (more than six months).

Important safety instructions for

wireless unit

1. Do not disassemble or tamper with the wire-

less unit.

2. Keep the wireless unit away from young chil-

dren. If accidentally swallowed, seek medical

attention immediately.

3. Use the wireless unit only with Makita tools.

4. Do not expose the wireless unit to rain or wet

conditions.

5. Do not use the wireless unit in places where

the temperature exceeds 50°C (122°F).

6. Do not operate the wireless unit in places

where medical instruments, such as heart

pace makers are near by.

7. Do not operate the wireless unit in places

where automated devices are near by. If oper-

ated, automated devices may develop malfunction

or error.

8. The wireless unit can produce electromagnetic

elds (EMF) but they are not harmful to the

user.

9. The wireless unit is an accurate instrument. Be

careful not to drop or strike the wireless unit.

10. Avoid touching the terminal of the wireless

unit with bare hands or metallic materials.

11. Always remove the battery on the tool when

installing the wireless unit.

12. When opening the lid of the slot, avoid the

place where dust and water may come into the

slot. Always keep the inlet of the slot clean.

13. Always insert the wireless unit in the correct

direction.

14. Do not press the wireless activation button

on the wireless unit too hard and/or press the

button with an object with a sharp edge.

15. Always close the lid of the slot when

operating.

16. Do not remove the wireless unit from the slot

while the power is being supplied to the tool.

Doing so may cause a malfunction of the wireless

unit.

17. Do not remove the sticker on the wireless unit.

18. Do not put any sticker on the wireless unit.

19. Do not leave the wireless unit in a place where

static electricity or electrical noise could be

generated.

20. Do not leave the wireless unit in a place sub-

ject to high heat, such as a car sitting in the

sun.

21. Do not leave the wireless unit in a dusty or

powdery place or in a place corrosive gas

could be generated.

22. Sudden change of the temperature may bedew

the wireless unit. Do not use the wireless unit

until the dew is completely dried.

23. When cleaning the wireless unit, gently wipe

with a dry soft cloth. Do not use benzine, thin-

ner, conductive grease or the like.

24. When storing the wireless unit, keep it in the

supplied case or a static-free container.

25. Do not insert any devices other than Makita

wireless unit into the slot on the tool.

26. Do not use the tool with the lid of the slot dam-

aged. Water, dust, and dirt come into the slot may

cause malfunction.

27. Do not pull and/or twist the lid of the slot more

than necessary. Restore the lid if it comes off

from the tool.

28. Replace the lid of the slot if it is lost or

damaged.

SAVE THESE INSTRUCTIONS.

6 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridgermlymaycausethemtoslipoffyourhands

and result in damage to the tool and battery cartridge

andapersonalinjury.

►1. Red indicator 2. Button 3. Battery cartridge

Toremovethebatterycartridge,slideitfromthetool

while sliding the button on the front of the cartridge.

Toinstallthebatterycartridge,alignthetongueonthe

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

itmayaccidentallyfalloutofthetool,causinginjuryto

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

catetheremainingbatterycapacity.Theindicatorlamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Tool / battery protection system

Thetoolisequippedwithatool/batteryprotectionsys-

tem.Thissystemautomaticallycutsoffpowertothe

motortoextendtoolandbatterylife.Thetoolwillauto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the battery is operated in a manner that causes

it to draw an abnormally high current, the tool automat-

ically stops without any indication. In this situation, turn

the tool off and stop the application that caused the tool

tobecomeoverloaded.Thenturnthetoolontorestart.

7 ENGLISH

Overheat protection

When the tool or battery is overheated, the tool stops

automatically. In this case, let the tool and battery cool

before turning the tool on again.

NOTE: When the tool is overheated, the lamp blinks.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically. In this case, remove the battery from the

tool and charge the battery.

Switch action

WARNING: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

►1. Switch trigger

Tostartthetool,simplypulltheswitchtrigger.Tool

speed is increased by increasing pressure on the switch

trigger. Release the switch trigger to stop.

Speed change

Therevolutionsandblowsperminutecanbeadjusted

byturningtheadjustingdial.Thedialismarked1(low-

est speed) to 5 (full speed).

►1.Adjustingdial

Refer to the table below for the relationship between the

numberontheadjustingdialandtherevolutionsand

blows per minute.

Number Revolutions per

minute

Blows per minute

5 980 5,000

4 810 4,130

3 640 3,260

2 470 2,400

1 300 1,550

CAUTION: Do not turn the adjusting dial when

the tool is running. Failure to do so may result in

the loss of control of the tool and cause an injury.

NOTICE: If the tool is operated continuously at

low speed for a long time, the motor will get over-

loaded, resulting in tool malfunction.

NOTICE: The speed adjusting dial can be turned

only as far as 5 and back to 1. Do not force it past

5 or 1, or the speed adjusting function may no

longer work.

NOTE: Soft no-load rotation function (For XRH10/

XRH11)

Whenthespeedadjustingdialissetto"3"orhigher,

the tool automatically reduces the speed at no-load to

reduce the vibration under no-load. Once operation

starts with a bit against concrete, blows per minute

increase and reach the numbers as shown in the

table. When temperature is low and there is less

uidityingrease,thetoolmaynothavethisfunction

even with the motor rotating.

Thisfunctionisnotavailablewhenthedustcollection

system is installed.

Lighting up the front lamp

►1. Lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pulltheswitchtriggertolightupthelamp.Thelamp

keeps on lighting while the switch trigger is being pulled.

Thelampgoesoutapproximately10secondsafter

releasing the switch trigger.

8 ENGLISH

CAUTION: For XRH10/XRH11

If the lamp goes off after blinking for a few sec-

onds, the active feedback sensing technology or

the soft no-load rotation function is not working

properly. Ask your local Makita Service Center for

repair.

NOTE: Use a dry cloth to wipe the dirt off the lens of

the lamp. Be careful not to scratch the lens of lamp, or

it may lower the illumination.

NOTE: If the dust collection system is installed on the

tool, the lamp of the dust collection system lights up

instead of the lamp of the tool.

Reversing switch action

►1. Reversing switch lever

CAUTION: Always check the direction of

rotation before operation.

CAUTION: Use the reversing switch only after

the tool comes to a complete stop. Changing the

direction of rotation before the tool stops may dam-

age the tool.

CAUTION: When not operating the tool,

always set the reversing switch lever to the neu-

tral position.

Thistoolhasareversingswitchtochangethedirection

of rotation. Depress the reversing switch lever from the

AsideforclockwiserotationorfromtheBsideforcoun-

terclockwise rotation.

When the reversing switch lever is in the neutral posi-

tion, the switch trigger cannot be pulled.

Changing the quick change chuck

for SDS-plus

For XRH11

ThequickchangechuckforSDS-pluscanbeeasily

exchanged for the quick change drill chuck.

Removing the quick change chuck

for SDS-plus

CAUTION: Before removing the quick change

chuck for SDS-plus, be sure to remove the bit.

Grasp the change cover of the quick change chuck for

SDS-plus and turn in the direction of the arrow until

the change cover line moves from the symbol to

the symbol. Pull forcefully in the direction of the arrow.

1 2

►1. Quick change chuck for SDS-plus 2. Change

cover 3. Change cover line

Installing the quick change drill chuck

Check the line of the quick change drill chuck shows

the symbol. Grasp the change cover of the quick

change drill chuck and set the line to the symbol.

Place the quick change drill chuck on the spindle of the

tool. Grasp the change cover of the quick change drill

chuck and turn the change cover line to the symbol

until a click can clearly be heard.

1 2

►1. Quick change drill chuck 2. Spindle 3. Change

cover line 4. Change cover

Selecting the action mode

NOTICE: Do not rotate the action mode chang-

ing knob when the tool is running.Thetoolwillbe

damaged.

NOTICE: To avoid rapid wear on the mode

change mechanism, be sure that the action mode

changing knob is always positively located in one

of the three action mode positions.

9 ENGLISH

Rotation with hammering

For drilling in concrete, masonry, etc., rotate the action

mode changing knob to the symbol. Use a tungsten-

carbide tipped bit (optional accessory).

►1. Rotation with hammering 2.Actionmodechang-

ing knob

Rotation only

For drilling in wood, metal or plastic materials, rotate

the action mode changing knob to the symbol. Use a

twist drill bit or wood drill bit.

►1. Rotation only

Hammering only

For chipping, scaling or demolition operations, rotate

the action mode changing knob to the symbol. Use a

bull point, cold chisel, scaling chisel, etc.

►1. Hammering only

Hook

CAUTION: Never hook the tool at high loca-

tion or on potentially unstable surface.

►1. Hook

Thehookisconvenientfortemporarilyhangingthetool.

Tousethehook,simplyliftuphookuntilitsnapsinto

the open position. When not in use, always lower hook

until it snaps into the closed position.

Adjusting the nozzle position of the

dust collection system

Optional accessory

Pushintheguidewhilepushinguptheguideadjust-

ment button, and then release the button at the desired

position.

1 2

►1. Guide 2.Guideadjustmentbutton

NOTE:Beforeadjustingthenozzleposition,release

the nozzle forward completely by pushing up the

guideadjustmentbutton.

10 ENGLISH

If a long drill bit is installed, extend the guide by pushing

up the extension button.

►1. Extension button

Adjusting the drilling depth of the

dust collection system

Optional accessory

Slidethedepthadjustmentbuttontothedesiredposi-

tionwhilepushingitup.Thedistance(A)isthedrilling

depth.

►1.Depthadjustmentbutton

Torque limiter

NOTICE: As soon as the torque limiter actuates,

switch off the tool immediately.Thiswillhelppre-

vent premature wear of the tool.

NOTICE: Drill bits such as hole saw, which tend

to pinch or catch easily in the hole, are not appro-

priate for this tool.Thisisbecausetheywillcause

the torque limiter to actuate too frequently.

Thetorquelimiterwillactuatewhenacertaintorque

levelisreached.Themotorwilldisengagefromthe

output shaft. When this happens, the drill bit will stop

turning.

Electronic function

Thetoolisequippedwiththeelectronicfunctionsfor

easy operation.

• Constantspeedcontrol

Thespeedcontrolfunctionprovidestheconstant

rotation speed regardless of load conditions.

• ActiveFeedbacksensingTechnology(ForXRH10/

XRH11)

If the tool is swung at the predetermined accelera-

tion during operation, the motor is forcibly stopped

to reduce the burden on the wrist.

NOTE:Thisfunctiondoesnotworkiftheacceleration

does not reach the predetermined one when the tool

is swung.

NOTE: If the bit is swung at the predetermined

acceleration during chipping, scaling, or demolishing,

the motor is forcibly stopped. In this case, release

the switch trigger, and then pull the switch trigger to

restart the tool.

Electric brake

Thistoolisequippedwithanelectricbrake.Ifthetool

consistently fails to quickly stop after the switch trigger

is released, have the tool serviced at a Makita service

center.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

Side grip (auxiliary handle)

CAUTION: Always use the side grip to ensure

safe operation.

CAUTION: After installing or adjusting the

side grip, make sure that the side grip is rmly

secured.

Toinstallthesidegrip,followthestepsbelow.

1. Loosen the thumb screw on the side grip.

►1.Thumbscrew

11 ENGLISH

2. Attachthesidegripwhilepressingthethumb

screwsothatthegroovesonthegriptintheprotru-

sions on the tool barrel.

►1.Thumbscrew

3. Tightenthethumbscrewtosecurethegrip.The

gripcanbexedatdesiredangle.

Grease

Coat the shank end of the drill bit beforehand with a

small amount of grease (about 0.5 - 1 g).

Thischucklubricationassuressmoothactionandlon-

ger service life.

Installing or removing drill bit

Clean the shank end of the drill bit and apply grease

before installing the drill bit.

►1. Shank end 2. Grease

Insertthedrillbitintothetool.Turnthedrillbitandpush

it in until it engages.

Afterinstallingthedrillbit,alwaysmakesurethatthe

drill bit is securely held in place by trying to pull it out.

►1. Drill bit

Toremovethedrillbit,pullthechuckcoverdownallthe

way and pull the drill bit out.

►1. Drill bit 2. Chuck cover

Chisel angle (when chipping,

scaling or demolishing)

Thechiselcanbesecuredatthedesiredangle.To

change the chisel angle, rotate the action mode chang-

ingknobtotheOsymbol.Turnthechiseltothedesired

angle.

►1.Actionmodechangingknob

Rotate the action mode changing knob to the

sym-

bol.Thenmakesurethatthechiselissecurelyheldin

place by turning it slightly.

12 ENGLISH

Depth gauge

Thedepthgaugeisconvenientfordrillingholesof

uniform depth.

Press and hold the lock button, and then insert the

depth gauge into the hex hole. Make sure that the

toothed side of the depth gauge faces the marking.

►1. Depth gauge 2. Lock button 3. Marking

4.Toothedside

Adjustthedepthgaugebymovingitbackandforth

whilepressingthelockbutton.Aftertheadjustment,

release the lock button to lock the depth gauge.

NOTE: Make sure that the depth gauge does not

touch the main body of the tool when attaching it.

Installing or removing the dust

collection system

Optional accessory

Toinstallthedustcollectionsystem,insertthetoolinto

the dust collection system all the way until it locks in

place with a little double click.

Toremovethedustcollectionsystem,pullthetoolwhile

pressing the lock-off button.

►1. Lock-off button

13 ENGLISH

Dust cup

Optional accessory

Use the dust cup to prevent dust from falling over the

tool and on yourself when performing overhead drilling

operations.Attachthedustcuptothebitasshownin

thegure.Thesizeofbitswhichthedustcupcanbe

attached to is as follows.

Model Bit diameter

Dust cup 5 6 mm (1/4") - 14.5 mm (9/16")

Dust cup 9 12 mm (15/32") - 16 mm (5/8")

►1. Dust cup

Dust cup set

Optional accessory

Before installing the dust cup set, remove the bit from

the tool if installed.

Install the dust cup set on the tool so that the

sym-

bol on the dust cup is aligned with the groove in the tool.

►1. symbol 2. Groove

NOTE: If you connect a vacuum cleaner to the dust

cup set, remove the dust cap before connecting it.

►1. Dust cap

Toremovethedustcupset,removethebitwhilepulling

the chuck cover in the direction of the arrow.

►1. Bit 2. Chuck cover

Hold the root of dust cup and pull it out.

14 ENGLISH

NOTE: If the cap comes off from the dust cup, attach

it with its printed side facing up so that groove on the

captsintheinsideperipheryoftheattachment.

OPERATION

CAUTION: Always use the side grip (auxiliary

handle) and rmly hold the tool by both side grip

and switch handle during operations.

CAUTION: Always make sure that the work-

piece is secured before operation.

CAUTION: Do not pull the tool out forcibly

even the bit gets stuck. Loss of control may

cause injury.

CAUTION: The dust collection system is

intended for drilling in concrete only. Do not use

the dust collection system for drilling in metal or

wood.

CAUTION: When using the tool with the dust

collection system, be sure to attach the lter

to the dust collection system to prevent dust

inhalation.

CAUTION: Before using the dust collection

system, check that the lter is not damaged.

Failure to do so may cause dust inhalation.

CAUTION: The dust collection system col-

lects the generated dust at a considerable rate,

but not all dust can be collected.

NOTICE: Do not use the dust collection system

for core drilling or chiseling.

NOTICE: Do not use the dust collection system

for drilling in wet concrete or use this system

in wet environment. Failure to do so may cause

malfunction.

NOTE: If the battery cartridge is in low temperature,

the tool’s capability may not be fully obtained. In this

case, warm up the battery cartridge by using the

tool with no load for a while to fully obtain the tool’s

capability.

Hammer drilling operation

CAUTION:Thereistremendousandsudden

twisting force exerted on the tool/drill bit at the time of

hole break-through, when the hole becomes clogged

with chips and particles, or when striking reinforcing

rods embedded in the concrete. Always use the side

grip (auxiliary handle) and rmly hold the tool by

both side grip and switch handle during opera-

tions. Failure to do so may result in the loss of control

ofthetoolandpotentiallysevereinjury.

Set the action mode changing knob to the symbol.

Position the drill bit at the desired location for the hole,

then pull the switch trigger. Do not force the tool. Light

pressure gives best results. Keep the tool in position

and prevent it from slipping away from the hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the tool at

an idle, then remove the drill bit partially from the hole.

By repeating this several times, the hole will be cleaned

out and normal drilling may be resumed.

NOTE: Eccentricity in the drill bit rotation may occur

whileoperatingthetoolwithnoload.Thetoolauto-

maticallycentersitselfduringoperation.Thisdoesnot

affect the drilling precision.

15 ENGLISH

Chipping/Scaling/Demolition

Set the action mode changing knob to the symbol.

Holdthetoolrmlywithbothhands.Turnthetoolon

and apply slight pressure on the tool so that the tool will

not bounce around, uncontrolled.

Pressing very hard on the tool will not increase the

efciency.

Drilling in wood or metal

CAUTION: Hold the tool rmly and exert care

when the drill bit begins to break through the

workpiece.Thereisatremendousforceexertedon

the tool/drill bit at the time of hole break through.

CAUTION: A stuck drill bit can be removed

simply by setting the reversing switch to reverse

rotation in order to back out. However, the tool

may back out abruptly if you do not hold it rmly.

CAUTION: Always secure workpieces in a

vise or similar hold-down device.

NOTICE: Never use “rotation with hammering”

when the drill chuck is installed on the tool.The

drill chuck may be damaged.

Also,thedrillchuckwillcomeoffwhenreversingthe

tool.

NOTICE: Pressing excessively on the tool will

not speed up the drilling. In fact, this excessive

pressure will only serve to damage the tip of your drill

bit, decrease the tool performance and shorten the

service life of the tool.

Set the action mode changing knob to the symbol.

For XRH08/XRH10

Optional accessory

Attachthechuckadaptertoakeylessdrillchuckto

which 1/2"-20 size screw can be installed, and then

install them to the tool. When installing it, refer to the

section “Installing or removing drill bit”.

►1. Keyless drill chuck 2. Chuck adapter

For XRH11

Use the quick change drill chuck as standard equipment. When

installing it, refer to "changing the quick change chuck for SDS-plus".

Hold the ring and turn the sleeve counterclockwise to open the

chuckjaws.Placethebitinthechuckasfarasitwillgo.Holdthe

ringrmlyandturnthesleeveclockwisetotightenthechuck.

►1. Sleeve 2. Ring

Toremovethebit,holdtheringandturnthesleeve

counterclockwise.

Diamond core drilling

NOTICE: If performing diamond core drilling

operations using “rotation with hammering”

action, the diamond core bit may be damaged.

When performing diamond core drilling operations, always set

the change lever to the

position to use "rotation only" action.

Disposing of dust

Optional accessory

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

16 ENGLISH

CAUTION: Be sure to wear dust mask when

disposing of dust.

CAUTION: Empty the dust case regularly

before the dust case becomes full. Failure to do so

may decrease the dust collection performance and

cause dust inhalation.

CAUTION: The performance of dust collection

decreases if the lter in the dust case become

clogged. Replace the lter with new one after

approximately 200 times of dust fulllment as a

guide. Failure to do so may cause dust inhalation.

1. Remove the dust case while pressing down the

lever of the dust case.

►1. Lever

2. Open the cover of the dust case.

►1. Cover

3. Disposeofthedust,andthencleanthelter.

NOTICE: When cleaning the lter, do not touch

the lter with brush or similar, or blow com-

pressed air on the lter. It may damage the lter.

Blow-out bulb

Optional accessory

Afterdrillingthehole,usetheblow-outbulbtocleanthe

dust out of the hole.

Using dust cup set

Optional accessory

Fit the dust cup set against the ceiling when operating

the tool.

NOTICE: Do not use the dust cup set when drill-

ing in metal or similar. It may damage the dust

cup set due to the heat produced by small metal

dust or similar.

NOTICE: Do not install or remove the dust cup

set with the drill bit installed in the tool. It may

damage the dust cup set and cause dust leak.

17 ENGLISH

WIRELESS ACTIVATION

FUNCTION

Optional accessory for XRH10/XRH11

What you can do with the wireless

activation function

Thewirelessactivationfunctionenablescleanandcom-

fortable operation. By connecting a supported vacuum

cleaner to the tool, you can run the vacuum cleaner

automatically along with the switch operation of the tool.

Tousethewirelessactivationfunction,preparefollow-

ing items:

• Awirelessunit(optionalaccessory)

• Avacuumcleanerwhichsupportsthewireless

activation function

Theoverviewofthewirelessactivationfunction

setting is as follows. Refer to each section for detail

procedures.

1. Installing the wireless unit

2. Toolregistrationforthevacuumcleaner

3. Starting the wireless activation function

Installing the wireless unit

Optional accessory

CAUTION: Place the tool on a at and stable

surface when installing the wireless unit.

NOTICE: Clean the dust and dirt on the tool

before installing the wireless unit. Dust or dirt

may cause malfunction if it comes into the slot of the

wireless unit.

NOTICE: To prevent the malfunction caused by

static, touch a static discharging material, such

as a metal part of the tool, before picking up the

wireless unit.

NOTICE: When installing the wireless unit,

always be sure that the wireless unit is inserted

in the correct direction and the lid is completely

closed.

1. Openthelidonthetoolasshowninthegure.

►1. Lid

2. Insert the wireless unit to the slot and then close

the lid.

Wheninsertingthewirelessunit,aligntheprojections

with the recessed portions on the slot.

►1. Wireless unit 2.Projection3. Lid 4. Recessed

portion

18 ENGLISH

When removing the wireless unit, open the lid slowly.

Thehooksonthebackofthelidwillliftthewirelessunit

as you pull up the lid.

►1. Wireless unit 2. Hook 3. Lid

Afterremovingthewirelessunit,keepitinthesupplied

case or a static-free container.

NOTICE: Always use the hooks on the back of

the lid when removing the wireless unit. If the

hooks do not catch the wireless unit, close the lid

completely and open it slowly again.

Tool registration for the vacuum

cleaner

NOTE:AMakitavacuumcleanersupportingthe

wireless activation function is required for the tool

registration.

NOTE: Finish installing the wireless unit to the tool

before starting the tool registration.

NOTE: During the tool registration, do not pull the

switch trigger or turn on the power switch on the

vacuum cleaner.

NOTE: Refer to the instruction manual of the vacuum

cleaner, too.

If you wish to activate the vacuum cleaner along with

theswitchoperationofthetool,nishthetoolregistra-

tion beforehand.

1. Install the batteries to the vacuum cleaner and the

tool.

2. Set the stand-by switch on the vacuum cleaner to

"AUTO".

►1. Stand-by switch

3. Press the wireless activation button on the vac-

uum cleaner for 3 seconds until the wireless activation

lampblinksingreen.Andthenpressthewirelessacti-

vation button on the tool in the same way.

1 2

►1. Wireless activation button 2. Wireless activation

lamp

If the vacuum cleaner and the tool are linked success-

fully, the wireless activation lamps will light up in green

for 2 seconds and start blinking in blue.

19 ENGLISH

NOTE:Thewirelessactivationlampsnishblinking

in green after 20 seconds elapsed. Press the wireless

activation button on the tool while the wireless acti-

vation lamp on the cleaner is blinking. If the wireless

activation lamp does not blink in green, push the wire-

lessactivationbuttonbrieyandholditdownagain.

NOTE: When performing two or more tool registra-

tionsforonevacuumcleaner,nishthetoolregistra-

tion one by one.

Starting the wireless activation

function

NOTE: Finish the tool registration for the vacuum

cleaner prior to the wireless activation.

NOTE: Refer to the instruction manual of the vacuum

cleaner, too.

Afterregisteringatooltothevacuumcleaner,the

vacuum cleaner will automatically runs along with the

switch operation of the tool.

1. Install the wireless unit to the tool.

2. Connect the hose of the vacuum cleaner with the

tool.

3. Set the stand-by switch on the vacuum cleaner to

"AUTO".

►1. Stand-by switch

4. Push the wireless activation button on the tool

briey.Thewirelessactivationlampwillblinkinblue.

1 2

►1. Wireless activation button 2. Wireless activation

lamp

5. Pull the switch trigger of the tool. Check if the

vacuum cleaner runs while the switch trigger is being

pulled.

Tostopthewirelessactivationofthevacuumcleaner,

push the wireless activation button on the tool.

NOTE:Thewirelessactivationlamponthetoolwill

stop blinking in blue when there is no operation for

2 hours. In this case, set the stand-by switch on the

vacuumcleanerto"AUTO"andpushthewireless

activation button on the tool again.

NOTE:Thevacuumcleanerstarts/stopswithadelay.

Thereisatimelagwhenthevacuumcleanerdetects

a switch operation of the tool.

NOTE:Thetransmissiondistanceofthewirelessunit

may vary depending on the location and surrounding

circumstances.

NOTE: When two or more tools are registered to one

vacuum cleaner, the vacuum cleaner may start run-

ning even if you don't pull the switch trigger because

an other user is using the wireless activation function.

20 ENGLISH

Description of the wireless activation lamp status

►1. Wireless activation lamp

Thewirelessactivationlampshowsthestatusofthewirelessactivationfunction.Refertothetablebelowforthe

meaning of the lamp status.

Status Wireless activation lamp Description

Color

Blinking

Duration

Standby Blue

2 hours Thewirelessactivationofthevacuumcleanerisavailable.The

lamp will automatically turn off when no operation is performed

for 2 hours.

When

the tool is

running.

Thewirelessactivationofthevacuumcleanerisavailableandthe

tool is running.

Tool

registration

Green

20 seconds Ready for the tool registration. Waiting for the registration by the

vacuum cleaner.

2 seconds Thetoolregistrationhasbeennished.Thewirelessactivation

lamp will start blinking in blue.

Cancelling

tool

registration

Red

20 seconds Ready for the cancellation of the tool registration. Waiting for the

cancellation by the vacuum cleaner.

2 seconds Thecancellationofthetoolregistrationhasbeennished.The

wireless activation lamp will start blinking in blue.

Others Red

3 seconds Thepowerissuppliedtothewirelessunitandthewirelessactiva-

tion function is starting up.

Off - - Thewirelessactivationofthevacuumcleanerisstopped.

La page charge ...

Makita XRH10Z-DC18RD Manuel utilisateur

Marque: Makita

Modèle: XRH10Z-DC18RD

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Makita XRH10Z-DC18RD User manual
español: Makita XRH10Z-DC18RD Manual de usuario

Makita XRH10Z-DC18RD Manuel utilisateur

Makita XRH10Z-DC18RD Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents