Yamaha QL1 Manuel utilisateur

EN

How to Use This Reference Manual

The QL5/QL1 V5 Reference Manual (this document) allows you

to search for terms and take advantage of links in the text.

Searching for terms

To search for a term, use the search function of the software

you’re using to view this document.

If you’re using Adobe Reader, enter the term in the search box

and press the <Enter> key of your computer keyboard to search

for occurrences of that term.

Displaying the next/previous view

If you’re using Adobe Reader, you can jump to the previous/next

view in your viewing history. This is a convenient way to jump back

to the previous page after you’ve used a link to jump to a different

page.

Using the Function Tree

A function tree for the QL series is provided on page 4 and

following. You can use this function tree to find the page that

explains an on-screen display or function.

V5 Reference Manual

Contents

V5 Reference Manual

2

Contents

How to Use This Reference Manual .......................................................................... 1

Function Tree ............................................................................ 4

SELECTED CHANNEL section ...................................................... 6

Operations in the SELECTED CHANNEL section ....................................................... 6

Channel Strip section.............................................................. 12

Operations in the Channel Strip section................................................................. 12

Input and output patching..................................................... 16

Changing the input patch settings......................................................................... 17

Changing the output patch settings ...................................................................... 18

Inserting an external device into a channel ............................................................ 20

Directly outputting an INPUT channel ................................................................... 22

Input channels ........................................................................ 25

Signal flow for input channels................................................................................ 25

Specifying the channel name, icon, and channel color........................................... 26

Making HA (Head Amp) settings............................................................................ 28

Sending the signal from an input channel to the STEREO/MONO bus ................... 34

Added pan function (Monaural input channels only) ............................................. 36

Sending a signal from an input channel to a MIX/MATRIX bus .............................. 38

Channel name display indication ........................................................................... 41

Correcting delay between channels (Input Delay).................................................. 41

Surround output for input channels....................................................................... 44

Channel library operations..................................................................................... 49

OUTPUT channels.................................................................... 50

Signal flow for output channels ............................................................................. 50

Specifying the channel name, icon, and channel color........................................... 51

Sending signals from MIX channels to the STEREO/MONO bus ............................. 52

Sending signals from MIX channels and STEREO/MONO channels to

MATRIX buses............................................................................................. 54

Correcting delay between channels (Output Delay)............................................... 56

Using the PORT TO PORT function ........................................................................ 57

Channel library operations..................................................................................... 58

EQ and Dynamics .................................................................... 59

Using EQ ............................................................................................................... 59

Simultaneously setting EQ type .............................................................................. 62

Using dynamics ...................................................................................................... 63

Using the EQ or Dynamics libraries ......................................................................... 66

Channel Job ............................................................................. 67

DCA group............................................................................................................. 67

Mute group............................................................................................................ 69

Using the Recall Safe function................................................................................. 72

Channel Link function ............................................................................................ 76

Copying, moving, or initializing a channel.............................................................. 80

About Mix Minus.................................................................................................... 84

Scene memory ......................................................................... 85

Storing and recalling scenes ................................................................................... 86

Editing scene memories.......................................................................................... 90

Using the Global Paste function.............................................................................. 92

Using the Focus Recall function .............................................................................. 95

Using the Fade function.......................................................................................... 97

Outputting a control signal to an external device in tandem with scene recall

(GPI OUT) ................................................................................................... 99

Playing back an audio file that links to a scene recall............................................. 100

Using Preview mode............................................................................................. 102

Monitor and Cue functions ................................................... 103

Using the Monitor function .................................................................................. 104

Using the Cue function......................................................................................... 110

Talkback and Oscillator......................................................... 118

Using Talkback ..................................................................................................... 118

Using the Oscillator function ................................................................................ 120

Meters.................................................................................... 123

Operations in the METER screen ........................................................................... 123

Graphic EQ, Parametric EQ, effects, and Premium Rack....... 129

About the virtual rack ........................................................................................... 129

Virtual rack operations.......................................................................................... 130

Graphic EQ operations ......................................................................................... 133

About AUTOMIXER............................................................................................... 140

Editing the internal effects .................................................................................... 143

Effects and tempo synchronization ....................................................................... 149

Using the Premium Rack....................................................................................... 151

Using the graphic EQ, parametric EQ, effect, and Premium Rack libraries ............. 162

Contents

V5 Reference Manual

3

I/O devices and external head amps .................................... 163

Using an I/O device ............................................................................................. 163

Remotely controlling an R series unit ................................................................... 166

Third-party equipment’s HA control function....................................................... 170

Remotely controlling an amp............................................................................... 172

Remotely controlling WIRELESS unit..................................................................... 173

Using an external head amp ................................................................................ 177

Remotely controlling an external head amp......................................................... 179

Controlling an internal head amp ........................................................................ 181

MIDI....................................................................................... 183

MIDI functionality on the QL series console ......................................................... 183

Basic MIDI settings .............................................................................................. 183

Using program changes to recall scenes and library items.................................... 186

Using control changes to control parameters....................................................... 188

Using parameter changes to control parameters .................................................. 190

Recorder................................................................................ 191

About the USB memory recorder ......................................................................... 191

Assigning channels to the input/output of the recorder ....................................... 191

Recording audio to a USB flash drive.................................................................... 193

Playing back audio files from a USB flash drive ..................................................... 195

Editing the title list............................................................................................... 196

Recording or playing back using a computer DAW .............................................. 197

Using the QL console with Nuendo Live .............................................................. 200

Setup ..................................................................................... 204

About the SETUP screen....................................................................................... 204

User settings ........................................................................................................ 207

Preferences .......................................................................................................... 214

USER DEFINED keys ............................................................................................. 216

Functions that can be assigned to USER DEFINED keys ........................................ 217

USER DEFINED knobs........................................................................................... 222

Functions that can be assigned to USER DEFINED knobs ...................................... 223

Custom fader bank .............................................................................................. 224

Console Lock ....................................................................................................... 226

Saving and loading setup data to and from a USB flash drive............................... 227

Remount function to USB flash drives .................................................................. 234

Word clock and slot settings ................................................................................ 234

Using cascade connections .................................................................................. 236

Basic settings for MIX buses and MATRIX buses ................................................... 240

Switching the entire phantom power supply on/off ............................................. 241

Specifying the brightness of the touch screen, LEDs, channel name displays,

and lamps................................................................................................. 241

Setting the date and time of the internal clock ..................................................... 242

Setting the network address ................................................................................. 242

Setting up the Dante audio network..................................................................... 244

Dante Device Lock................................................................................................ 246

Support for Dante Domain Manager .................................................................... 247

Using GPI (General Purpose Interface) .................................................................. 258

Help function......................................................................... 263

Loading a Help/text file from a USB flash drive ..................................................... 263

Viewing Help........................................................................................................ 263

Using USER DEFINED keys to recall Help directly................................................... 264

Other functions ..................................................................... 265

Initializing the unit to factory default settings ....................................................... 265

Adjusting the detection point of the touch screen (Calibration function) .............. 265

Adjusting the faders (Calibration function) ........................................................... 266

Fine-tuning the input and output gain (Calibration function) ............................... 266

Adjusting the LED color (Calibration function) ...................................................... 268

Adjusting the brightness of the channel name display .......................................... 268

Adjusting the contrast of the channel name display.............................................. 269

Initializing the Dante audio network settings ........................................................ 269

Update procedure for NAME SUB CPU firmware................................................... 269

Update function to Dante firmware ...................................................................... 270

Warning/Error Messages ...................................................... 271

Index...................................................................................... 274

Function Tree

V5 Reference Manual

4

Function Tree

Page numbers in parentheses ( ) are the page numbers of the

Owner’s Manual (booklet).

Main

SELECTED CHANNEL 6

OVERVIEW 12

FUNCTION ACCESS AREA (17)

CHANNEL PARAMETER

PATCH/NAME 17, 26, 51

GAIN/PATCH 28

1ch 28

8ch 30

CH1–32 32

CH33–64/ST IN 32

OUTPUT

Indication only

INPUT DELAY 41

8ch 42

CH1–32 42

CH33–64/ST IN 42

DELAY SCALE 42

INSERT/DIRECT OUT 20

1ch 20, 23

8ch 21, 23

HPF/EQ 59

1ch 59

8ch 61

CH1–32 62

CH33–64/ST IN 62

OUTPUT 62

DYNAMICS 64

1ch 64

KEY IN SOURCE SELECT 65

8ch 65

CH1–32 66

CH33–64/ST IN 66

OUTPUT 66

MIX SEND/MATRIX SEND 41

TO STEREO/MONO 52

8ch 52

CH1–32 53

CH33–64/ST IN 53

OUTPUT 53

SURROUND 44

LIBRARY

CHANNEL LIBRARY 49

EQ LIBRARY 66

DYNAMICS LIBRARY 66

GEQ/PEQ LIBRARY 162

EFFECT LIBRARY 162

Portico5033/Portico5043/Portico5045/U76/

Opt-2A/EQ-1A/DynamicEQ/Buss Comp 369/

MBC4 LIBRARY

162

DANTE INPUT PATCH LIBRARY 164

RACK

VIRTUAL RACK 130

RACK MOUNTER 133

GEQ EDIT 134

GEQ LINK 134

EFFECT RACK 145

EFFECT EDIT 145

EFFECT TYPE 145

PREMIUM RACK 151

PREMIUM RACK MOUNTER 151

PREMIUM RACK EDIT 152

AUTOMIXER 140

PARAMETRIC EQ 137

I/O DEVICE

DANTE PATCH 163

DANTE SETUP 163

DANTE INPUT PATCH 164

DANTE OUTPUT PATCH 165

I/O 166

REMOTE HA EDIT 171

DANTE OUTPUT PATCH 165

AMP 172

DANTE OUTPUT PATCH 165

WIRELESS 173

EXTERNAL HA 180

EXTERNAL HA PORT SELECT 180

EXTERNAL HA EDIT 181

INTERNAL HA 182

MONITOR

MONITOR 104

CUE 113

MONITOR 106

OSCILLATOR 121

TALKBACK 119

METER

INPUT METER 123

OUTPUT METER 123

RTA METER 125

SETUP

USER SETUP 204

PREFERENCE 214

USER DEFINED KEYS SETUP 216

USER DEFINED KEY SETUP (List) 216

USER DEFINED KNOBS SETUP 222

USER DEFINED KNOB SETUP (List) 222

CUSTOM FADER BANK/MASTER FADER 225

FADER ASSIGN SELECT 224

USER LEVEL/CREATE USER KEY 207

CREATE KEY 208

SAVE KEY 211

LOGIN 209

Function Tree

V5 Reference Manual

5

NOTE

• The explanations in this reference manual will use the QL5.

• In the case of the QL1, some screens will not show channels

and faders that do not exist on those models.

SAVE/LOAD 227

WORD CLOCK/SLOT 234

CASCADE IN/OUT PATCH 237, 239

OUTPUT PORT 56

MIDI/GPI 183, 258

MIDI SETUP 184

PROGRAM CHANGE 186

CONTROL CHANGE 189

GPI 259

FADER START 261

BUS SETUP 240

SURROUND SETUP 205

CONSOLE LOCK 226

DATE/TIME 242

NETWORK 243

DANTE SETUP 244

SCENE

SCENE LIST 87

GLOBAL PASTE 93

FADE TIME 97

SONG SELECT 101

FOCUS RECALL 96

PREVIEW 102

RECORDER

USB 191

NUENDO LIVE 200

CH JOB

CH LINK MODE 77

DCA GROUP ASSIGN 68

MUTE GROUP ASSIGN 70

RECALL SAFE MODE 73

CH COPY MODE 81

CH MOVE MODE 82

CH DEFAULT MODE 83

SETUP PATCH

PORT SELECT

21, 24, 30, 107,

114, 165, 180,

238

CH SELECT 18, 131, 192

Others

CONFIRMATION 214

SOFT KEYBOARD (23)

LOGIN 209

Startup Menu

MODE SELECT 265

INITIALIZE ALL MEMORIES 265

INITIALIZE CURRENT MEMORIES 265

TOUCH SCREEN CALIBRATION 265

INPUT PORT TRIM 267

OUTPUT PORT TRIM 267

SLOT OUTPUT TRIM 267

FADER CALIBRATION 266

LED COLOR CALIBRATION 268

SELECTED CHANNEL section

V5 Reference Manual

6

SELECTED CHANNEL section

The SELECTED CHANNEL section located at the right of the display corresponds to a

channel module of a conventional analog mixer, and allows you to use the knobs on the panel

to set all the major parameters of the currently-selected channel.

Operations in this section will affect the channel that was most recently selected by its [SEL]

key. If you have assigned an ST IN channel or STEREO channel to a single channel strip,

either the L or the R channel will be selected, and the major parameters for L and R channels

will be linked.

Operations in the SELECTED CHANNEL section

Follow the steps below to perform operations in the SELECTED CHANNEL section.

NOTE

• The number and name of the currently-selected

channel is shown in the channel select field located in

the Function Access Area of the touch screen.

• If an ST IN channel or STEREO channel has been

assigned to a single channel strip, you can switch

between L and R by repeatedly pressing the same

[SEL] key.

• You can also switch channels by pressing the channel select field located in the Function Access

Area. Press the left side of the field to select the preceding channel. Press the right side of the

field to select the next channel.

• If you have turned on the option “POPUP APPEARS WHEN KNOB(S) PRESSED” on the

PREFERENCE tab (accessed by pressing the SETUP button, then the USER SETUP button),

pressing a knob repeatedly will open or close the screen (1ch).

• Even if a different screen is selected, the channel selected with the

[SEL] key can be set using the knobs of the SELECTED CHANNEL

section. In this case, a window indicating the value of that parameter will

appear on screen when you operate a knob.

SELECTED CHANNEL VIEW screen

 SEND field

In this field, you can view the send level and pre/post from the channel

to each MIX/MATRIX bus. You can also switch the on/off status of the

send signals. The view and the function of the knobs and buttons in

the SEND field vary depending on whether a pair of bus channels

(odd-numbered and even-numbered) are comprised of two mono

channels or a stereo channel.

1 Tabs

Enable you to select a group of 16 output bus channels to be

displayed in the SEND field.

• MIX tab .................................. displays MIX buses 1–16.

• MATRIX tab ........................... displays MATRIX buses 1–8.

STEP

1. Press the Bank Select keys in the Fader Bank section to select the bank that includes

the channel you want to operate.

2. Use a [SEL] key in the top panel channel strip section or the master section, to select

the channel to control.

3. If the SELECTED CHANNEL VIEW screen is not displayed, press one of the knobs in

the SELECTED CHANNEL section.

4. Use the knobs and the buttons in the screen to edit the parameters of the selected

channel.

Channel number

Channel name

1

SELECTED CHANNEL section

V5 Reference Manual

7

If the destination bus channels are two mono channels:

1 SEND knob

Adjusts the send level to the corresponding bus.

2 PRE indicator

Indicates the send point of the corresponding bus. If the PRE button on the MIX SEND

8ch screen is turned ON, this PRE indicator will be turned on.

3 ON button

Switches the send signal to the corresponding bus on or off.

If the destination bus is a stereo channel:

1 SEND/PAN knob

The right-hand knob adjusts the level of the signal sent to a pair of bus channels (even-

numbered and odd-numbered). The left-hand knob adjusts the pan and balance of the

same signal.

2 PRE indicator

Indicates the send point of the corresponding bus. If the PRE button on the MIX SEND

8ch screen is turned ON, this PRE indicator will be turned on.

3 ON button

Switches the send signal to the two buses on or off.

NOTE

• If the indices of a SEND/PAN knob are white, the send point is assigned as PRE; if the indices

are black, it is assigned as POST.

• If the send point is PRE, you can specify the PRE point as either VARI [PRE EQ] or VARI [PRE

FADER] in the BUS SETUP popup that appears when you press the SETUP button  BUS

SETUP button.

• If the type of the destination bus is set to FIXED, controllers

1–2 mentioned above will not be

displayed. The send level will be fixed at nominal level, and the send point will be fixed at POST

FADER. For details, see “Basic settings for MIX buses and MATRIX buses” on page 240.

• Press the SEND knob or PAN knob on screen to open the SEND 8ch window.

When using CUE B

Indicates that channels 7 and 8 on the MATRIX

bus are combined with CUE B.

NOTE

For details about how to use CUE B, see the

CUE screen (When configuring CUE B).

 GAIN/PATCH field

This field enables you to make HA (head amp) analog or digital gain settings. You can also

view the operational status of the head amp.

1 GAIN knob

Sets the analog gain/digital gain of the head amp.

Press the knob to open the GAIN/PATCH 1ch

window.

2 GC indicator

Indicates the fixed gain value output to the audio

network if the Gain Compensation function is

turned on.

3 OVER indicator

Warns you when the signal is clipping.

4 Ø (Phase) indicator

Indicates the status of the phase setting.

5 +48V indicator

Indicates the phantom power (+48V) on or off status for the head amp.

6 HPF ON indicator

Indicates the HPF on/off status of the external head amp.

7 AG-DG LINK indicator

Indicates a link between the analog gain and digital gain of the head amp.

8 Digital/Analog gain value

If analog gain is assigned to the GAIN knob, the digital gain value is shown here. If digital

gain is assigned to the GAIN knob, the analog gain value is shown here.

NOTE

• For an input channel that is patched to an input that has no head amp, 1, 2, 5, 6, and 7

will not be shown. For an output channel,

1–7 will not be shown.

• If GAIN KNOB FUNCTION is set to DIGITAL GAIN in the USER SETUP PREFERENCE

screen, the digital gain knob will appear for

1, and 2, 5, 6, and 7 will not be shown. For

details, refer to “Making HA (Head Amp) settings” on page 28.

1

2

3

1

2

3

5

876

1

4

2

SELECTED CHANNEL section

V5 Reference Manual

8

If patched to a wireless mic (SELECTED CHANNEL VIEW screen)

1 RX.GAIN knob/TX.GAIN knob/TX.ATT knob

Sets the gain for the transmitter or receiver. Press the knob

to open the GAIN/PATCH 1ch window.

The knob name will change depending on the connected

device.

NOTE

When remote control connection is disabled for the connected

device, a gray circle is displayed here instead of a knob, and the

gain cannot be adjusted.

2 OL indicator

Lights if the audio signal level of the receiver reaches the overload point.

3 RF (Radio Frequency) signal meter

Shows bars to indicate the level of the RF signal.

An active antenna indicator is shown on the right side. It indicates which antenna is

enabled.

NOTE

• The display will change depending on the device.

• For more information about the relationship between the number of bars and the actual strength

of the RF signal, refer to the manual from each developer.

4 Battery indicator

Shows bars to indicate the remaining battery power.

NOTE

For more information about the relationship between the number of bars and maximum operation

time, refer to the manual from Shure.

5 MUTE indicator

Indicates the mute status (on/off) of the audio signal for the receiver.

6 Frequency

Indicates the frequency that is currently set for the RF signal.

 PAN/BALANCE field

This field enables you to switch the on/off status of the signal sent from the selected channel

to the STEREO/MONO bus, and adjust the pan and balance.

The view and the function of the controllers in this field vary depending on the type of the

selected channel.

When an input channel or MIX channel is selected:

1 TO STEREO PAN knob

Sets the pan position of a signal routed to the

STEREO bus.

Press the knob to open the STEREO/MONO 8ch

window. If the ST IN channel is selected, you can

specify whether to view the PAN knob or the

BALANCE knob in this window. For a MIX channel,

the PAN knob will appear if the signal is mono, and

the BALANCE knob will appear if the signal is stereo.

NOTE

• For mono input channels, the pan level is nominal at center and +3dB when panned either left or

right. These levels do not change even if channel link is used.

• For ST IN channels, if the PAN knob is selected, the pan level is nominal when panned either left

or right and -3dB at center. If the BALANCE knob is selected the balance level is nominal at

center and +3dB when panned either left or right. These levels do not change even if channel link

is used.

2 ST/MONO button

Switches the on/off status of a signal sent from the

channel to the STEREO/MONO bus.

If an INPUT/MIX channel is set to LCR mode, the

LCR button appears in location

2. The LCR button

is an overall on/off switch for the signals sent from

the channel to the STEREO/MONO bus.

When a MATRIX, STEREO, or MONO channel is selected:

1 BALANCE knob

If the signal on the selected channel is stereo, the

BALANCE knob will appear, enabling you to adjust

the volume balance for the left and right channels.

If the channel signal is monaural, the BALANCE

knob is not shown and cannot be used.

Press the knob to open the TO STEREO 8ch

window.

When using Surround mode (MIX1-MIX6)

3 DOWN MIX

This field enables you to view the downmix

coefficient and L/R button settings.

Press this field to open the TO STEREO/MONO

window.

1

2

3

6

5

4

1

2

1

3

SELECTED CHANNEL section

V5 Reference Manual

9

 INPUT DELAY field

This field enables you to view the delay settings.

1 ON indicator

Indicates the on/off status of the delay.

2 Delay time

The delay value is displayed by milliseconds (ms) and also by currently-selected scale. If

the scale uses units of ms, the value in the bottom row will not be displayed. Only the

ms value appears in the middle row.

Press this field to open the INPUT DELAY 8ch window.

 HPF field (input channels only)

This field enables you to set the HPF. If an output channel

is selected, a gray circle will appear in location

1, and 2

will not be displayed.

1 HPF knob

Sets the HPF cutoff frequency.

2 ON button

Switches the HPF on or off.

 EQ parameter field

This field displays the 4-band EQ parameter settings. Press each

knob to open the HPF/EQ 1ch window.

1 Q knob

Specifies the Q for each band.

If the HIGH band filter type is set to LPF or H. SHELF (high-

shelving), or the LOW band filter type is set to L. SHELF

(low-shelving), the Q knob will not be displayed. Only the

filter type name will be displayed.

NOTE

• Fully rotating the HIGH band Q knob on the panel counter-

clockwise while pressing and holding it down will set the filter

type to LPF. Fully rotating the Q knob clockwise while pressing

and holding it down will set the filter type to high-shelving.

• Fully rotating the LOW band Q knob on the panel clockwise while

pressing and holding it down will set the filter type to low-

shelving.

• If an output channel has been selected, fully rotating the LOW

band Q knob on the panel counter-clockwise while pressing and holding it down will set the filter

type to HPF.

• You can also switch the filter type in the HPF/EQ 1ch window.

2 FREQUENCY knob

Sets the center frequency (or cutoff frequency) for each band.

3 GAIN knob

Sets the amount of cut/boost for each band.

NOTE

• If the HIGH band filter type is set to LPF, you can switch LPF on or off using the HIGH band GAIN

knob on the panel.

• If the LOW band filter type is set to HPF, you can switch HPF on or off using the LOW band GAIN

knob on the panel.

NOTE

When the BYPASS button is on, the knobs turn gray.

 EQ graph field

This field graphically indicates the approximate response of the EQ. Press this field to open

the HPF/EQ 1ch window, in which you can set the attenuator, HPF, and EQ.

 DYNAMICS 1/DYNAMICS 2 field

This field enables you to set the Dynamics 1/2 parameters.

1 OVER indicator

Warns you when the signal is clipping.

2 Level meter

Displays the output signal level (green) and the amount of gain reduction (orange)

when the Dynamics is on. The current threshold setting is shown as a white vertical line.

3 Threshold

Specifies the threshold.

1

2

1

2

1 2 3

1 2

3

4

SELECTED CHANNEL section

V5 Reference Manual

10

4 Parameters

Indicate the values of parameters that vary depending on the currently-selected

dynamics type.

Press this field to open the DYNAMICS 1/DYNAMICS 2 1ch window, in which you can

make detailed parameter settings.

 INSERT field

This field enables you to make insert settings.

1 Popup button

Press this button to open the INSERT/DIRECT OUT 1ch

window.

2 ON button

Switches the insert on or off.

3 RACK EDIT button

Appears if an effect or Premium Rack is inserted. Press this button to display the edit

screen for the inserted rack.

4 IN indicator

Appears if a port has been assigned to the insert-in patch. It lights when the signal is

sent to the insert-in.

 DIRECT OUT field

This field enables you to make Direct Out settings.

1 Popup button

Press this button to open the INSERT/DIRECT OUT 1ch

window. The Direct Out level value will appear below the

button.

2 ON button

Switches the Direct Out on or off.

 RECALL SAFE field

This field enables you to make Recall Safe settings.

1 Popup button

Press this button to open the RECALL SAFE window.

2 ON button

Switches the Recall Safe status on or off.

3 PARTIAL indicator

This will light if recall safe applies only to some of the parameters, not to all channel

settings.

 FADER field

This field enables you to make settings for the channel on/off

status and the level.

1 Fader

Displays the current level.

Use the faders on the top panel to set the levels.

2 Level indicator

Displays the current level setting by numerical value. If

the signal is clipping at any point in the channel, the

ΣCLIP indicator will light.

3 ON button

Switches the channel on or off. The button is linked with

the corresponding [ON] key on the top panel.

4 CUE SETTINGS button

Use this button to open the CUE SETTINGS screen.

 DCA/MUTE field

This field enables you to select the DCA or mute group to which the

channel is assigned.

1 Tabs

Select a DCA or mute group. Press the selected tab once again

to open the DCA/MUTE GROUP ASSIGN MODE window.

When the DCA group tab is selected:

2 DCA group select buttons

Select the DCA group to which the channel is assigned.

3 Mute group indicators

Indicate the mute group to which the channel is assigned.

1

2

43

21

2

1

3

1

2

3

4

When two channels are

used for CUE, and CUE

OPERATION MODE is set

to CH

1

3

2

1

3

2

SELECTED CHANNEL section

V5 Reference Manual

11

When the mute group tab is selected:

4 Mute group select buttons

Select the mute group to which the channel is assigned.

NOTE

If the dimmer level is set to the mute group, this button lights

orange.

5 MUTE SAFE button

Temporarily removes the channel from the mute group.

6 DCA group indicators

Indicate the DCA group to which the channel is assigned.

4

5

6

Channel Strip section

V5 Reference Manual

12

Channel Strip section

The Channel Strip section located below the touch screen lets you recall and control input

channels, output channels, or DCA groups. If you press the Bank Select key in the Fader Bank

section, you can control them using the faders, [ON] keys, and [CUE] keys for the channels

or DCA groups corresponding to that key.

Operations in the Channel Strip section

 CHANNEL NAME field

This field appears at the top and bottom of the screen and displays the channel number,

name, and icon for the currently-selected eight channels. The name of the currently-selected

channel is highlighted.

 GAIN/PATCH field

This field enables you to make HA (head amp) analog or digital gain settings. You can also

view the operational status of the head amp.

The view and the function of the controllers in this field vary depending on the type of the

selected channel.

If the head amp is patched:

1 GAIN knob

Sets the analog gain of the head amp.

• Press this field to assign the GAIN knob to the [TOUCH AND TURN] knob, which

enables you to adjust the gain. If the Gain Compensation function is turned on, an

indicator appears, showing the level of the signal output to the audio network.

• If the GAIN knob has been assigned to the [TOUCH AND TURN] knob, press the knob

to open the GAIN/PATCH 8ch window.

2 OVER indicator

Lights when a signal at the input port or from the rack output exceeds the full scale level.

This indicator is available only if an input channel is selected.

3 +48V indicator

Indicates the phantom power (+48V) on or off status for the head amp. This indicator is

not displayed unless the head amp is patched to the channel.

4 Ø (Phase) indicator (input channels only)

Indicates the input phase setting for the head amp.

NOTE

• If the slot is not connected to the head amp, the patch and the type of the MY card will be

displayed.

• Press the SETUP button, then the USER SETUP button, select the PREFERENCE tab, and then

set the GAIN KNOB FUNCTION to DIGITAL GAIN. You will be able to adjust the digital gain value

by using the [TOUCH AND TURN] knob.

STEP

1. Use the Bank Select keys to select the channels or DCA groups that you want to

control.

2. Use the faders and [ON] keys in the Channel Strip section to adjust the level of the

selected channels and switch them on or off.

3. Use the fields on the OVERVIEW screen and the [TOUCH AND TURN] knob to adjust

the parameters for the channels.

Bank Select keys

Channel Strip section

OVERVIEW screen

NOTE

The OVERVIEW screen

appears when you press a

USER DEFINED key to which

OVERVIEW is assigned.

: Selected channel

: Unselected channel

1

4

3

2

Channel Strip section

V5 Reference Manual

13

• If GAIN KNOB FUNCTION is set to DIGITAL GAIN, the DIGITAL GAIN knob will appear instead

of knob

1, and indicator 3 will not be displayed.

• You can also operate the digital gain by assigning INPUT GAIN DIGITAL GAIN to a USER

DEFINED knob, or by assigning an ALTERNATE function to a USER DEFINED key and then

adjusting the USER DEFINED knob or the GAIN knob for the selected channel while

ALTERNATE is on.

If patched to a wireless mic (OVERVIEW screen)

1 RX.GAIN knob/TX.GAIN knob/TX.ATT knob

Sets the gain for the transmitter or receiver.

• Press this field to assign the GAIN knob to the [TOUCH AND TURN] knob, which

enables you to adjust the gain. If the Gain Compensation function is turned on, an

indicator appears, showing the level of the signal output to the audio network.

• If the GAIN knob has been assigned to the [TOUCH AND TURN] knob, press the knob

to open the GAIN/PATCH 8ch window.

• The name of knob will change depending on the connected device.

NOTE

When remote control connection is disabled for the connected device, a gray circle is displayed

here instead of a knob, and the gain cannot be adjusted.

2 RF (Radio Frequency) signal meter

Shows bars to indicate the level of the RF signal.

An active antenna indicator is shown on the right side. It indicates which antenna is

enabled.

NOTE

• The display will change depending on the device.

• For more information about the relationship between the number of bars and the actual strength

of the RF signal, refer to the manual from each developer.

3 Battery indicator

Shows bars to indicate the remaining battery power.

NOTE

For more information about the relationship between the number of bars and maximum operation

time, refer to the manual from each developer.

4 OL indicator

Lights if the audio signal level of the receiver reaches the overload point.

NOTE

If the audio signal for the receiver is muted, 5 is displayed.

5 MUTE indicator

Displayed only if the audio signal for the receiver is muted.

NOTE

If the audio signal for the receiver is not muted, 4 is displayed.

 INPUT DELAY field (input channels only)

This field displays the delay status for the input channel. Press this field to open the INPUT

DELAY 8ch window.

1 DELAY ON/OFF indicator

Indicates the on/off status of the delay.

 INSERT/DIRECT OUT field

This field displays the Insert/Direct out status. Press this field to open the INSERT 8ch

window.

1 INSERT ON/OFF indicator

Indicates the insert on/off status.

2 DIRECT OUT ON/OFF indicator (input channels only)

Indicates the Direct Out on/off status.

1 2

3 4 5

If the slot is patched:

The slot name will appear.

If the rack is connected:

The patch and module name will appear.

If the output is connected:

Only the patch will appear.

1

2

Channel Strip section

V5 Reference Manual

14

 EQ field

This field graphically indicates the approximate response of

the EQ. Press this field to open the HPF/EQ 1ch window, in

which you can set the HPF and EQ.

NOTE

If DCA or monitor has been selected, this field will be blank.

 DYNAMICS 1/2 field

This field displays the threshold value and meter for Dynamics

1/2. Press this field to open the DYNAMICS 1/2 1ch window.

NOTE

If DCA or monitor has been selected, this field will be blank.

 SEND field

This field displays the send level, send on/off status, and pre/post

settings for 16 buses.

To select the 16 destination buses, use the [MIX/MATRIX] key in the

Fader Bank section.

Use the [TOUCH AND TURN] knob to adjust the send level for each bus.

Touch the knob of the bus you want to operate; it will be assigned to the

[TOUCH AND TURN] knob. If it is assigned to the [TOUCH AND TURN]

knob, touching that knob once again will display the SEND 8ch popup

screen.

This field varies depending on the type of the destination bus.

If the destination bus is VARI (mono):

The knob color and scale color indicate the send on/off and pre/post

status. If the send is off, the knob color turns gray. With the post setting,

the knob scale color turns gray.

If the destination bus is VARI (stereo):

If a pair of buses (odd-numbered and even-numbered) are in stereo, the left-hand knob will

function as the PAN knob, and the right-hand knob will function as the SEND knob.

If the destination bus is set to FIXED:

The SEND ON/OFF button for each bus is shown instead of the knob.

 TO STEREO/MONO field

This field displays the on/off status and pan/balance setting of the signal sent to the STEREO/

MONO bus.

This field varies depending on the type of the selected channel.

When an input channel or MIX channel is selected:

1 TO STEREO PAN knob

Sets the pan position of a signal routed to the STEREO bus.

Press the knob to open the STEREO/MONO 8ch window. If the ST IN channel is selected,

you can specify whether to view the PAN knob or the BALANCE knob in this window.

For a MIX channel, the PAN knob will appear if the signal is mono, and the BALANCE

knob will appear if the signal is stereo.

2 ST/MONO indicator

Indicates the status of a signal sent to the STEREO/MONO bus.

If an input or MIX channel is set to LCR mode, the LCR indicator

will be displayed.

1

2

Channel Strip section

V5 Reference Manual

15

When a MATRIX channel (monaural) or MONO channel is selected:

The ΣCLIP indicator will light if the signal is clipping at some point in the channel.

For a stereo MATRIX channel or STEREO channel, the BALANCE knob appears, indicating

the balance of the left/right channels.

 DCA group field

A DCA group (1–16) to which the channel is assigned is displayed on the first or second row

in this field.

Press this field to open the DCA/MUTE GROUP ASSIGN MODE window.

 Mute group field

A mute group (1–8) to which the channel is assigned is displayed on the third row in this field.

If the channel has been temporarily removed from the mute group, S (Safe) will appear on the

third row. If a dimmer level has been specified for a mute group, the color of the characters

will change from red to orange.

Press this field to open the DCA/MUTE GROUP ASSIGN MODE window.

Input and output patching

V5 Reference Manual

16

Input and output patching

This chapter explains how to edit the input patching and output patching, how to connect

inserts, and how to use direct outputs.

When the QL series is in the initial state, the following input ports (jacks/ports) are patched to

each input channel.

For QL5

For QL1

When the QL is in the initial state, the output ports (jacks/ports) are patched to the following

output channels.

*1. QL1: OMNI OUT1–6

*2. QL1: MIX1–6

*3. QL1: OMNI OUT7–8

Input patching

QL series consoles and I/O devices feature two types of patching: Dante audio network

patching and QL console internal patching.

For Dante audio network patching, you will use the DANTE INPUT PATCH window. In this

window, you can patch the QL console and I/O device inputs. Sixty-four (64) channels for the

QL5 and thirty-two (32) channels for the QL1 can be input from a DANTE audio network.

Choose channels from Dante audio network signals and select the I/O devices that you want

to control from the QL series console.

Then, route the input signals (that were patched in the DANTE INPUT PATCH window) to

channels on the QL series console. To do this, choose input ports from DANTE 1–64 (for QL5)

or DANTE1–32 (for QL1) in the GAIN/PATCH window.

Output patching

Use the OUTPUT PORT window to patch QL console’s output channels and Dante audio

network. In this window, assign output channel signals to DANTE 1–64 ports (for QL5) or

DANTE 1–32 ports (for QL1).

Next, patch the output signals from DANTE 1–64 (for QL5) or DANTE 1–32 (for QL1)

(assigned in the OUTPUT PORT window) to I/O device outputs. Use the OUTPUT PATCH

window of the I/O DEVICE to make these assignments.

QL console internal patching and Dante audio network

patching

The following diagram shows the signal flow through the QL series console, I/O devices, and

Dante audio network.

Input channels Input port (jack/port)

CH1–32 INPUT1–32

CH33–48 DANTE1–16

CH49–64 DANTE17–32

ST IN1L-4R FX5L(A)–FX8R(B)

Input channels Input port (jack/port)

CH1–16 INPUT1–16

CH17–32 DANTE1–16

ST IN1L-4R FX5L(A)–FX8R(B)

Output port (jack/port) Output channels

OMNI OUT1–14

*1

MIX1–14

*2

OMNI OUT15–16

*3

STEREO L/R

DANTE1–16 MIX1–16

DANTE17–24 MATRIX1–8

DANTE25–26 STEREO L/R

DANTE27 MONO

DANTE28–29 MONITOR L/R

DANTE30 MONITOR C

DANTE31–32 CUE L/R

SLOT1(1)–(16) MIX1–16

SLOT2(1)–(8) MATRIX1–8

SLOT2(9)–(10) STEREO L/R

SLOT2(11) MONO

SLOT2(12)–(13) MONITOR L/R

SLOT2(14) MONITOR C

SLOT2(15)–(16) CUE L/R

FX5L(A), FX6L(A), FX7L(A), FX8L(A) MIX13–16

DIGITAL OUT L/R STEREO L/R

RECORDER INPUT L/R STEREO L/R

Output port (jack/port) Output channels

32: QL5

16: QL1

16 16 64: QL5

32: QL1

SW

ID #2

ANALOG INPUT MY MY

INPUT PATCH

Dante Network

“Dante” (ports)

ID #3

ID #1

Dante-MY16-AUD

QL series console

I/O Device

I/O device

Dante

patching

QL series internal

patching

Input and output patching

V5 Reference Manual

17

Changing the input patch settings

NOTE

• You can also select an input port from the GAIN/PATCH window.

• The OVERVIEW screen appears when you press a USER DEFINED key to which OVERVIEW is

assigned.

PATCH/NAME screen

1 PATCH button

Indicates the currently-selected input port. If you press this button when selecting an

icon or changing the channel name, you will return to the input port select screen.

2 Channel icon button

Indicates the icon that is selected for the corresponding channel. When you press this

button, a screen will appear in which you can select an icon or sample name.

3 Channel name input box

Indicates the name that is assigned to the corresponding channel. When you press this

field, a keyboard window allowing you to change the channel name will appear.

4 Category select list

Selects the category of input port. The categories correspond to the following input

ports. The displayed categories vary depending on the channel type.

• DANTE1–32 .......... DANTE1–DANTE32

• DANTE33–64 ........ DANTE33–DANTE64 (QL5 only)

• INPUT/PB OUT ..... INPUT1–32

*1

, PB OUT(L), PB OUT(R)

• SLOT1 ................... SLOT1(1)–SLOT1(16)

• SLOT2 ................... SLOT2(1)–SLOT2(16)

• EFFECT RACK ..... FX1L(A)–FX8R(B)

• PREMIUM RACK .. PR1L(A)–PR2R(B)

*1. QL1: INPUT1–16

STEP

1.

Press the Bank Select keys in the Fader Bank section and the [SEL] keys on the top

panel to select the input channel you want to operate.

2. Press the channel number/channel name field on the OVERVIEW screen.

3. Select the type of port in the category select list on the PATCH/NAME screen, and

use the port select buttons to select the input port.

OVERVIEW screen PATCH/NAME screen

2 73

1

6

4

5

Input and output patching

V5 Reference Manual

18

5 Port select buttons

Select the input port that is assigned to the currently-selected channel.

6 Tabs

Enable you to switch between items.

7 Close button

Closes the screen.

Changing the output patch settings

To change the patching, you can either select the output port that will be the output destination

of each output channel, or you can select the output channel that will be the output source for

each output port.

Selecting the output port for each output channel

NOTE

With QL V1.07 and later, when you change from input channels to output channels using the Bank

Select keys, the SEND field of the SELECTED CHANNEL VIEW screen changes from the MIX

tab to the MATRIX tab. Then, if you switch back to input channels, the MIX tab will appear.

PATCH/NAME screen

1 PATCH button

Indicates the port that is patched to the output channel. If you press this button when

another tab is active, a window will appear, enabling you to select the network and port.

2 Channel select button

Selects the channel to set.

NOTE

Switching channels on this screen will not affect the channel selection on the console.

3 Channel icon button

Indicates the icon and color that are currently selected for the corresponding channel.

When you press this button, a screen will appear in which you can select an icon or

sample name.

4 Channel number display box

Indicates the channel number. This item cannot be changed.

5 Channel name input box

Indicates the name that is assigned to the corresponding channel. When you press this

field, a keyboard window allowing you to assign a name will appear.

6 Category select list

Select the type of port.

STEP

1. Press the Bank Select keys in the Fader Bank section and the [SEL] keys on the top

panel to select an output channel.

2. Press the channel number/channel name field on the OVERVIEW screen.

3. Select the type of port in the category select list on the PATCH/NAME screen, and

use the port select buttons to select the output port.

OVERVIEW screen PATCH/NAME screen

3 54

1

9

6

7

2

8

Input and output patching

V5 Reference Manual

19

7 Port select buttons

From the category, these buttons let you select the port to patch. To cancel the

selection, press the button once again.

8 Tabs

Enable you to switch between items.

9 Close button

Closes the screen.

Selecting the output channel for each output port

NOTE

If PATCH CONFIRMATION in the PREFERENCE tab on the USER SETUP screen is ON, a

confirmation dialog box will appear when you attempt to change the patch settings. If STEAL

PATCH CONFIRMATION is ON, a confirmation dialog box will appear when you attempt to

change a location that is already patched elsewhere.

CH SELECT screen

1 Category select list

Select the category of the channel. The categories correspond to the following channels.

They vary depending on the output port type.

• MIX/MATRIX ................................ MIX1–MIX16, MATRIX1–MATRIX8

• ST/MONO/MONI/CUE ................. STEREO L, STEREO R, MONO(C), MONI L,

MONI R, MONI C, CUE L, CUE R, SMON L, SMON

R, SMON C, SMON LFE, SMON Ls, SMON Rs,

MMTX L, MMTX R, MMTX C, MMTX LFE, MMTX

Ls, MMTX Rs

• DIRECT OUT 1–32 ...................... CH1–CH32 Direct Outs

• DIRECT OUT 33–64 .................... CH33–CH64 Direct Outs

• INSERT 1 OUT 1–32 ................... CH1–CH32 Insert 1 Outs

• INSERT 1 OUT 33–64 ................. CH33–CH64 Insert 1 Outs

• INSERT 1 OUT MIX/MATRIX ...... MIX1–MIX16, MATRIX1–MATRIX8 Insert 1 Outs

• INSERT 1 OUT ST/MONO........... STEREO L, STEREO R, MONO (C) Insert 1 Outs

• INSERT 2 OUT 1–32 ................... CH1–CH32 Insert 2 Outs

• INSERT 2 OUT 33–64 ................. CH33–CH64 Insert 2 Outs

• INSERT 2 OUT MIX/MATRIX ...... MIX1–MIX16, MATRIX1–MATRIX8 Insert 2 Outs

• INSERT 2 OUT ST/MONO........... STEREO L, STEREO R, MONO (C) Insert 2 Outs

• CASCADE MIX/MATRIX.............. MIX1–MIX16, MATRIX1–MATRIX8

• CASCADE ST/MONO/CUE ......... STEREO L, STEREO R, MONO (C), CUE L,

CUE R

NOTE

In the case of QL1, channels that do not exist on the model will not be shown.

STEP

1. In the Function Access Area, press the SETUP button.

2. Press the OUTPUT PORT button in the SYSTEM SETUP field located in the center of

the SETUP screen.

3. In the tabs below the OUTPUT PORT screen, select the output port you want to

control.

4. Press the channel select button of the port you want to operate.

5. Use the category select list and the channel select buttons to select the send-source

channel.

SETUP screen OUTPUT PORT screen

1

2

3

Input and output patching

V5 Reference Manual

20

2 Channel select button

Select the channel to be assigned to the output port from the current category.

3 CLOSE button

Closes the screen.

Inserting an external device into a channel

You can insert an effect processor or other external device into the signal path of an INPUT,

MIX, MATRIX, STEREO, or MONO channel. When doing so, the type of input/output port

used for the insertion and the location of the insertion in/out can be specified individually for

each channel.

NOTE

If you install a digital I/O card in a slot and digitally connect an external device, you must

synchronize the word clock of the QL console and the external device (page 234).

INSERT/DIRECT OUT window (1ch)

 INSERT field

This field enables you to make insert settings. Press one of three fields to choose PRE HPF

(immediately before the HPF), PRE EQ (immediately before the EQ) or PRE FADER

(immediately before the fader), or POST ON (immediately after the [ON] key) as the insert

position.

1 INSERT OUT button

Displays the currently-selected output port for insert 1 and insert 2. Press this button to

open the PORT SELECT window, and select an output port.

2 INSERT IN button

Displays the currently-selected input port for insert 1 and insert 2. Press this button to

open the PORT SELECT window, in which you can select an input port.

3 INSERT ON/OFF button

Switches the insert on or off.

4 APPLY TO ALL INPUT button (input channels only)

Specifies whether the insert point/direct out point settings will be applied to all input

channels.

5 APPLY TO ALL OUTPUT button (output channels only)

Specifies whether the insert point setting will be applied to all output channels.

NOTE

Insert 1 and insert 2 are serial connections with fixed sequential numbers.

STEP

1. Use the Bank Select keys in the Fader Bank section and the [SEL] keys on the top

panel to select the channel where you want to insert the external device.

2. Press the popup button in the INSERT field in the SELECTED CHANNEL VIEW screen.

3. Press the INSERT OUT or INSERT IN button.

4. Select an output port or an input port.

5. Press the INSERT ON button.

SELECTED CHANNEL VIEW screen INSERT/DIRECT OUT window (1ch)

9

8

77 663 9

5

1 42

La page charge ...

Yamaha QL1 Manuel utilisateur

Ce manuel convient également à

Yamaha QL1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents