Zanussi ZDLN7530 Manuel utilisateur

Catégorie
Lave-vaisselle
Taper
Manuel utilisateur
GETTING
STARTED?
EASY.
User Manual
ZDLN7530
EN User Manual 2
Dishwasher
FR Notice d'utilisation 25
Lave-vaisselle
VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair information:
www.zanussi.com/support
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away from the
appliance unless continuously supervised.
Children of less than 3 years of age should be kept away from
the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep detergents away from children.
Keep children and pets away from the appliance when the door
is open.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
This appliance is intended to be used in household and similar
applications such as:
farm houses; staff kitchen areas in shops, offices and other
working environments;
by clients in hotels, motels, bed & breakfast and other
residential type environments.
2
Do not change the specification of this appliance.
The operating water pressure (minimum and maximum) must be
between 0.5 (0.05) / 8 (0.8) bar (MPa)
Follow the maximum number of 13 place settings.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
Put the cutlery in the cutlery basket with the sharp ends
pointing down or put them in the cutlery drawer in a horizontal
position with the sharp edges down.
Do not leave the appliance with the open door unattended to
avoid stepping accidentally onto it.
Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
Do not use high pressure water sprays and/or steam to clean
the appliance.
If the appliance has ventilation openings in the base, they must
not be covered e.g. by a carpet.
The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
SAFETY INSTRUCTIONS
INSTALLATION
WARNING! Only a qualified person
must install this appliance.
Remove all the packaging.
Do not install or use a damaged appliance.
Do not use the appliance before installing it in
the built-in structure due to safety manner.
Follow the installation instructions supplied with
the appliance.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Do not install or use the appliance where the
temperature is less than 0 °C.
Install the appliance in a safe and suitable place
that meets installation requirements.
www.youtube.com/electrolux
www.youtube.com/aeg
How to install your 60 cm
Dishwasher Sliding Hinge
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
The appliance must be earthed.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Always use a correctly installed shockproof
socket.
Do not use multi-plug adapters and extension
cables.
Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
3
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
This appliance is fitted with a 13 A mains plug. If
it is necessary to change the mains plug fuse,
use only a 13 A ASTA (BS 1362) fuse (UK and
Ireland only).
WATER CONNECTION
Do not cause damage to the water hoses.
Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
Ensure that there are no visible water leaks
during and after the first use of the appliance.
The water inlet hose has a safety valve and a
sheath with an inner mains cable.
WARNING! Dangerous voltage.
If the water inlet hose is damaged, immediately
close the water tap and disconnect the mains
plug from the mains socket. Contact the
Authorised Service Centre to replace the water
inlet hose.
USE
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Dishwasher detergents are dangerous. Follow
the safety instructions on the detergent
packaging.
Do not drink and play with the water in the
appliance.
Do not remove the dishes from the appliance
until the programme is complete. Some
detergent may remain on the dishes.
Do not store items or apply pressure on the
open door of the appliance.
The appliance can release hot steam if you open
the door while a programme operates.
INTERNAL LIGHTING
WARNING! Risk of injury.
Concerning the lamp(s) inside this product and
spare part lamps sold separately: These lamps
are intended to withstand extreme physical
conditions in household appliances, such as
temperature, vibration, humidity, or are intended
to signal information about the operational
status of the appliance. They are not intended to
be used in other applications and are not
suitable for household room illumination.
To replace the internal lighting, contact the
Authorised Service Centre.
SERVICE
To repair the appliance contact the Authorised
Service Centre. Use original spare parts only.
Please note that self-repair or non-professional
repair can have safety consequences and might
void the guarantee.
The following spare parts will be available for 7
years after the model has been discontinued:
motor, circulation and drain pump, heaters and
heating elements, including heat pumps, piping
and related equipment including hoses, valves,
filters and aquastops, structural and interior
parts related to door assemblies, printed circuit
boards, electronic displays, pressure switches,
thermostats and sensors, software and firmware
including reset software. Please note that some
of these spare parts are only available to
professional repairers, and that not all spare
parts are relevant for all models.
The following spare parts will be available for 10
years after the model has been discontinued:
door hinge and seals, other seals, spray arms,
drain filters, interior racks and plastic peripherals
such as baskets and lids.
DISPOSAL
WARNING! Risk of injury or
suffocation.
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
Remove the door catch to prevent children and
pets to get closed in the appliance.
4
PRODUCT DESCRIPTION
5
4
67
9
8
12
2
3
11
10
1
1
Ceiling spray arm
2
Upper spray arm
3
Lower spray arm
4
Filters
5
Rating plate
6
Salt container
7
Air vent
8
Rinse aid dispenser
9
Detergent dispenser
10
Cutlery basket
11
Lower basket
12
Upper basket
BEAM-ON-FLOOR
The Beam-on-Floor is a light that is displayed on
the floor below the appliance door.
A red light comes on when a programme starts.
It remains on for the duration of the programme.
A green light comes on when the programme is
complete.
The red light flashes when the appliance has a
malfunction.
The Beam-on-Floor is off when the
appliance is deactivated.
5
CONTROL PANEL
1 2 3 4 5 6
1
On/Off button/Reset button
2
Delay start button
3
Display
4
Programme buttons
5
Option buttons
6
AUTO programme button
DISPLAY
A AB
A. Indicators
B. Time indicator
INDICATORS
Indicator Description
Rinse aid indicator. It is on when the rinse aid dispenser needs refilling. Refer to
"Before first use".
Salt indicator. It is on when the salt container needs refilling. Refer to "Before first
use".
Machine Care indicator. It is on when the appliance needs internal cleaning with the
Machine Care programme. Refer to "Care and cleaning".
Drying phase indicator. It is on when a programme with the drying phase is selec-
ted. It flashes when the drying phase operates. Refer to "Programme selection".
6
PROGRAMME SELECTION
PROGRAMMES
CA B D E
A. 30 min is the shortest programme suitable
for washing a load with fresh and light soil.
Pre-rinse is a programme for rinsing off
food remains from the dishes. It prevents
odours forming in the appliance. Do not use
detergent with this programme.
B. 60 min is a programme suitable for washing a
load with fresh and lightly dried-on soil.
C. 90 min is a programme suitable for washing
and drying normally soiled items.
D. 160 min is a programme suitable for washing
and drying heavily soiled items.
E. ECO is the longest programme offering the
most efficient use of energy and water
consumption for crockery and cutlery with
normal soil. This is the standard programme for
test institutes.
1)
OPTIONS
You can adjust the programme selection to your
needs by activating options.
Extra Power
This option improves the washing results of the
selected programme. It increases the wash
temperature and duration.
Glass Care
This option provides special care for a delicate
load. It prevents rapid changes in the wash
temperature of the selected programme and
reduces it to 45 °C. This protects glassware in
particular from damaging.
AUTO
This program automatically adjusts the wash cycle
to the type of load.
The appliance senses the degree of soil and the
amount of dishes in the baskets. It adjusts the
temperature and quantity of water as well as the
wash duration.
PROGRAMMES OVERVIEW
Programme Type of load Degree of soil Programme phases Options
30 min Crockery
Cutlery
Fresh Wash 50 °C
Intermediate rinse
Final rinse 45 °C
AirDry
Extra Power
Glass Care
Pre-rinse All types of
loads
All degrees
of soil
Prewash Options are not ap-
plicable to this pro-
gramme.
60 min Crockery
Cutlery
Fresh
Lightly
dried-on
Wash 60 °C
Intermediate rinse
Final rinse 50 °C
AirDry
Extra Power
Glass Care
1) This programme is used to assess compliance with the Ecodesign Comission Regulation (EU)
2019/2022.
7
Programme Type of load Degree of soil Programme phases Options
90 min Crockery
Cutlery
Pots
Pans
Normal
Lightly
dried-on
Wash 60 °C
Intermediate rinse
Final rinse 55 °C
Drying
AirDry
Extra Power
Glass Care
160 min Crockery
Cutlery
Pots
Pans
Normal to
heavy
Dried-on
Prewash
Wash 60 °C
Intermediate rinse
Final rinse 60 °C
Drying
AirDry
Extra Power
Glass Care
ECO Crockery
Cutlery
Pots
Pans
Normal
Lightly
dried-on
Prewash
Wash 50 °C
Intermediate rinse
Final rinse 60 °C
Drying
AirDry
Extra Power
Glass Care
AUTO Crockery
Cutlery
Pots
Pans
The pro-
gramme ad-
justs to all de-
grees of soil.
Prewash
Wash 50 - 60 °C
Intermediate rinse
Final rinse 55 °C
Drying
AirDry
Options are not ap-
plicable to this pro-
gramme.
Machine
Care
No load The pro-
gramme
cleans the ap-
pliance interi-
or.
Refer to "Care
and clean-
ing".
Wash 65 °C
Intermediate rinse
Final rinse
AirDry
Options are not ap-
plicable to this pro-
gramme.
Consumption values
Programme
1)
2)
Water (l) Energy (kWh) Duration (min)
30 min 9.3 - 11.4 0.54 - 0.66 30
Pre-rinse 4.1 - 5.1 0.01 - 0.04 15
60 min 10.6 - 12.9 0.80 - 0.93 60
90 min 10.4 - 12.7 0.97 - 1.10 90
160 min 10.8 - 13.2 0.97 - 1.11 160
ECO
10.5
3)
/ 10.5
4)
0.821
3)
/ 0.835
4)
240
3)
/ 240
4)
AUTO 9.6 - 13.1 0.74 - 1.06 120 - 170
8
Programme
1)
2)
Water (l) Energy (kWh) Duration (min)
Machine Care 8.9 - 10.9 0.58 - 0.70 60
1) The pressure and the temperature of the water, the variations of the mains supply, the options and the
quantity of dishes can change the values.
2) The values for programmes other than ECO are indicative only.
3) In accordance with the 1016/2010 regulation.
4) In accordance with the 2019/2022 regulation.
Information for test institutes
To receive the necessary information for conducting
performance tests (e.g. according to EN60436 ),
send an email to:
In your request, please include the product number
code (PNC) found on the rating plate.
For any other questions regarding your dishwasher,
please refer to the service book provided with your
appliance.
BASIC SETTINGS
You can configure the appliance by changing basic
settings according to your needs.
Number Settings Values
Description
1)
1 Water hardness From level 1L to
level 10L
Adjust the level of the water softener according
to the water hardness in your area.
Factory setting: 5L.
2 Rinse aid level From level 0A to
level 6A
Adjust the level of the rinse aid according to the
necessary dosage.
Factory setting: 4A.
3 End sound 1b (on)
0b (off)
Activate or deactivate the acoustic signal for the
end of a programme.
Factory setting: 0b.
4 Auto door open 1o (on)
0o (off)
Activate or deactivate the AirDry.
Factory setting: 1o.
5 Key tones 1F (on)
0F (off)
Activate or deactivate the sound of the buttons
when pressed.
Factory setting: 1F.
6 Latest pro-
gramme selec-
tion
1H (on)
0H (off)
Enable or disable the automatic selection of the
most recently used programme and options.
Factory setting: 0H.
1) For more details, refer to the information provided in this chapter.
You can change the basic settings in setting mode.
Instructions on how to configure the appliance are
provided further in this chapter.
When the appliance is in setting mode, the display
shows a digit and a letter. For each setting, a
9
dedicated letter is displayed. The dedicated letters
are indicated in the table.
The order of the basic settings presented in the
table is also the order of the settings in setting
mode.
THE WATER SOFTENER
The water softener removes minerals from the water
supply, which would have a negative effect on the
washing results and on the appliance.
The higher the content of these minerals, the harder
your water is. Water hardness is measured in
equivalent scales.
The water softener should be adjusted according to
the hardness of the water in your area. Your local
water authority can advise you on the hardness of
the water in your area. It is important to set the right
level of the water softener to assure good washing
results.
Water hardness
German degrees
(°dH)
French degrees
(°fH)
mmol/l
Clarke de-
grees
Water softener level
47 - 50 84 - 90 8.4 - 9.0 58 - 63 10
43 - 46 76 - 83 7.6 - 8.3 53 - 57 9
37 - 42 65 - 75 6.5 - 7.5 46 - 52 8
29 - 36 51 - 64 5.1 - 6.4 36 - 45 7
23 - 28 40 - 50 4.0 - 5.0 28 - 35 6
19 - 22 33 - 39 3.3 - 3.9 23 - 27
5
1)
15 - 18 26 - 32 2.6 - 3.2 18 - 22 4
11 - 14 19 - 25 1.9 - 2.5 13 - 17 3
4 - 10 7 - 18 0.7 - 1.8 5 - 12 2
<4 <7 <0.7 < 5
1
2)
1) Factory setting.
2) Do not use salt at this level.
Regardless of the type of detergent used, set
the proper water hardness level to keep the
salt refill indicator active.
Multi-tabs containing salt are not
effective enough to soften hard water.
Regeneration process
For the correct water softener operation, the resin
of the softener device needs to be regenerated
regularly. This process is automatic and is the part
of the normal dishwasher operation.
When the prescribed quantity of water (see values
in the table) has been used since the previous
regeneration process, a new regeneration process
will be initiated between the final rinse and the
programme end.
Water softener level Amount of water (l)
1 250
2 100
3 62
4 47
5 25
6 17
7 10
8 5
10
Water softener level Amount of water (l)
9 3
10 3
In case of the high water softener setting, it may
occur also in the middle of the programme, before
the rinse (twice during a programme). Regeneration
initiation has no impact on the cycle duration,
unless it occurs in the middle of a programme or at
the end of a programme with a short drying phase.
In that cases, the regeneration prolongs the total
duration of a programme by additional 5 minutes.
Subsequently, the rinsing of the water softener that
lasts 5 minutes may begin in the same cycle or at
the beginning of the next programme. This activity
increases the total water consumption of a
programme by additional 4 litres and the total
energy consumption of a programme by additional
2 Wh. The rinsing of the softener ends with a
complete drain.
Each performed softener rinse (possible more than
one in the same cycle) may prolong the programme
duration by another 5 minutes when it occurs at any
point at the beginning or in the middle of a
programme.
All the consumption values mentioned
in this section are determined in
accordance with the currently
applicable standard in laboratory
conditions with water hardness
2.5mmol/L according to the
2019/2022 regulation (water softener:
level 3).
The pressure and the temperature of
water as well as the variations of the
mains supply can change the values.
THE RINSE AID LEVEL
The rinse aid helps to dry the dishes without
streaks and stains. It is automatically released
during the hot rinse phase. It is possible to set the
released quantity of rinse aid.
When rinse aid chamber is empty, the rinse aid
indicator is on notifying to refill rinse aid. If the
drying results are satisfactory while using multi-
tablets only, it is possible to deactivate the
dispenser and the indicator. However, for best
drying performance, always use rinse aid and keep
the rinse aid indicator active.
To deactivate the rinse aid dispenser and indicator,
set the level of rinse aid to 0A.
END SOUND
You can activate an acoustic signal that sounds
when the programme is completed.
Acoustic signals sound also when a
malfunction of the appliance occurs. It
is not possible to deactivate these
signals.
AIRDRY
AirDry improves the drying results. The appliance
door opens automatically during the drying phase
and remains ajar.
AirDry is automatically activated with all
programmes other than Pre-rinse.
CAUTION! Do not try to close the
appliance door within 2 minutes after
automatic opening. This can cause
damage to the appliance.
CAUTION! If children have access to
the appliance, we advise to deactivate
AirDry. The automatic opening of the
door may pose a danger.
When AirDry opens the door, Beam-
on-Floor might not be completely
visible. To see if the programme is
complete, look at the control panel.
KEY TONES
The buttons on the control panel make a click
sound when you press them. You can deactivate
this sound.
LATEST PROGRAMME SELECTION
You can set the automatic selection of the most
recently used programme and options.
The latest programme that was completed before
the appliance deactivation is saved. It is then
11
selected automatically after you activate the
appliance.
When the latest programme selection is disabled,
the default programme is ECO.
SETTING MODE
How to enter setting mode
You can enter setting mode before starting a
programme. You cannot enter setting mode while
the programme is running.
To enter setting mode, press and hold
simultaneously 30 min and ECO for about 3
seconds.
The lights related to 60 min, 90 min and
160 min are on.
The display shows the current value of the
first available setting.
How to navigate in setting mode
You can navigate in setting mode using programme
buttons.
CA B
A. Previous button
B. OK button
C. Next button
Use Previous and Next to switch between the
basic settings and to change their value.
Use OK to enter the selected setting and to
confirm changing its value.
How to change a setting
Make sure the appliance is in setting mode.
1. Use Previous or Next to select the desired
setting.
The display shows the current setting value (a digit
and the dedicated letter).
2. Press OK to enter the setting.
The current setting value flashes.
3. Press Previous or Next to change the value.
4. Press OK to confirm the setting.
The new setting is saved.
The appliance returns to the basic settings
list.
5. Press and hold simultaneously 30 min and
ECO for about 3 seconds to exit setting mode.
The appliance returns to the programme selection.
The saved settings remain valid until you change
them again.
BEFORE FIRST USE
1. Make sure that the current level of the
water softener agrees with the hardness
of the water supply. If not, adjust the level
of the water softener.
2. Fill the salt container.
3. Fill the rinse aid dispenser.
4. Open the water tap.
5. Start the programme 30 min to remove any
residuals from the manufacturing process. Do
not use detergent and do not put dishes in the
baskets.
After starting the programme, the appliance
recharges the resin in the water softener for up to 5
minutes. The washing phase starts only after this
procedure is complete. The procedure is repeated
periodically.
THE SALT CONTAINER
CAUTION! Use rough salt designed
for dishwashers only. Fine salt
increases the risk of corrosion.
The salt is used to recharge the resin in the water
softener and to assure good washing results in
daily use.
How to fill the salt container
1. Turn the cap of the salt container
counterclockwise and remove it.
2. Put 1 litre of water in the salt container (only for
the first time).
3. Fill the salt container with dishwasher salt (until
it is full).
12
4. Carefully shake the funnel by its handle to get
the last granules inside.
5. Remove the salt around the opening of the salt
container.
6. Turn the cap of the salt container clockwise to
close the salt container.
CAUTION! Water and salt can come
out of the salt container when you fill
it. After you fill the salt container,
immediately start the shortest
programme to prevent corrosion. Do
not put dishes in the baskets.
HOW TO FILL THE RINSE AID DISPENSER
A
B
C
CAUTION! Only use rinse aid
designed specifically for dishwashers.
1. Open the lid (C).
2. Fill the dispenser (B) until the rinse aid reaches
the marking ''MAX''.
3. Remove the spilled rinse aid with an absorbent
cloth to prevent excessive foam formation.
4. Close the lid. Make sure that the lid locks into
position.
Fill the rinse aid dispenser when the
indicator (A) is clear.
DAILY USE
1. Open the water tap.
2. Press and hold until the appliance is
activated.
3. Fill the salt container if it is empty.
4. Fill the rinse aid dispenser if it is empty.
5. Load the baskets.
6. Add the detergent.
7. Select and start a programme.
8. Close the water tap when the programme is
complete.
USING THE DETERGENT
A
B
C
13
CAUTION! Only use detergent
specifically designed for dishwashers.
1. Press the release button (A) to open the lid (C).
2. Put the detergent, in powder or tablets, in the
compartment (B).
3. If the programme has a prewash phase, put a
small quantity of detergent on the inner part of
the appliance door.
4. Close the lid. Make sure that the lid locks into
position.
HOW TO SELECT AND START A
PROGRAMME
1. Press the button dedicated to the programme
you want to set.
The light related to the button is on.
The display shows the programme duration.
2. Activate applicable options if desired.
3. Close the appliance door to start the
programme.
HOW TO SELECT AND START THE
PROGRAMME PRE-RINSE
1. To select Pre-rinse, press and hold 30 min for
3 seconds.
The light related to the button is on.
The display shows the programme duration.
Options are not applicable to this
programme.
2. Close the appliance door to start the
programme.
HOW TO ACTIVATE OPTIONS
1. Select a programme.
2. Press the button dedicated to the option you
want to activate.
The light related to the button is on.
The display shows the updated programme
duration.
By default, options must be activated
every time before you start a
programme.
If the latest programme selection is
enabled, the saved options are
activated automatically along with the
programme.
It is not possible to activate or
deactivate options while a programme
is running.
Not all options are compatible with
each other.
Activating options often increases the
water and energy consumption as well
as the programme duration.
HOW TO SELECT AND START THE
PROGRAMME AUTO
1. Press AUTO.
The light related to the button is on.
The display shows the programme duration.
Options are not applicable to this
programme.
2. Close the appliance door to start the
programme.
The appliance senses the type of load and adjusts
a suitable wash cycle. During the cycle, the sensors
operate several times and the initial programme
duration can decrease.
HOW TO DELAY THE START OF A
PROGRAMME
1. Select a programme.
2. Press repeatedly until the display shows
the desired delay time (from 1 to 24 hours).
The light related to the button is on.
3. Close the appliance door to start the
countdown.
During the countdown, it is not possible to change
the delay time and the programme selection.
When the countdown is complete, the programme
starts.
HOW TO CANCEL THE DELAY START WHILE
THE COUNTDOWN OPERATES
Press and hold for about 3 seconds.
The appliance returns to the programme selection.
If you cancel the delay start, you have
to select the programme again.
HOW TO CANCEL A RUNNING
PROGRAMME
Press and hold for about 3 seconds.
The appliance returns to the programme selection.
Make sure that there is detergent in
the detergent dispenser before you
start a new programme.
14
OPENING THE DOOR WHILE THE
APPLIANCE OPERATES
Opening the door while a programme is running
stops the appliance. It may affect the energy
consumption and the programme duration. After
closing the door, the appliance continues from the
point of interruption.
If the door is opened for more than 30
seconds during the drying phase, the
running programme ends. It does not
happen if the door is opened by AirDry
function.
THE AUTO OFF FUNCTION
This function saves energy by switching the
appliance off when it is not operating.
The function comes into operation automatically:
When the programme is completed.
After 5 minutes if a programme was not started.
END OF THE PROGRAMME
When the programme is complete, the display
shows 0:00.
The Auto Off function switches the appliance off
automatically.
All buttons are inactive except for the on/off button.
HINTS AND TIPS
GENERAL
Follow the hints below to ensure optimal cleaning
and drying results in daily use and to protect the
environment.
Washing dishes in the dishwasher as instructed
in the user manual usually consumes less water
and energy than washing dishes by hand.
Load the dishwasher to its full capacity to save
water and energy. For best cleaning results,
arrange items in the baskets as instructed in the
user manual and do not overload the baskets.
Do not pre-rinse dishes by hand. It increases
the water and energy consumption. When
needed, select a programme with a prewash
phase.
Remove larger residues of food from the dishes
and empty cups and glasses before putting
them inside the appliance.
Soak or slightly scour cookware with firmly
cooked-on or baked-on food before washing it
in the appliance.
Make sure that items in the baskets do not
touch or cover each other. Only then can the
water completely reach and wash the dishes.
You can use dishwasher detergent, rinse aid
and salt separately or you can use the multi-
tablets (e.g. ''All in 1''). Follow the instructions
on the packaging.
Select a programme according to the type of
load and the degree of soil. ECO offers the
most efficient use of water and energy
consumption.
To prevent limescale buildup inside the
appliance:
Refill the salt container whenever
necessary.
Use the recommended dosage of the
detergent and rinse aid.
Make sure that the current level of the water
softener agrees with the hardness of the
water supply.
Follow the instructions in the chapter "Care
and cleaning".
USING SALT, RINSE AID AND DETERGENT
Only use salt, rinse aid and detergent designed
for dishwasher. Other products can cause
damage to the appliance.
In areas with hard and very hard water, we
recommend to use basic dishwasher detergent
(powder, gel, tablets containing no additional
agents), rinse aid and salt separately for optimal
cleaning and drying results.
Detergent tablets do not fully dissolve with short
programmes. To prevent detergent residues on
the tableware, we recommend that you use
tablets with long programmes.
Always use the correct quantity of detergent.
Insufficient dosage of detergent can result in
poor cleaning results and hard-water filming or
spotting on the items. Using too much detergent
with soft or softened water results in detergent
residues on the dishes. Adjust the amount of
detergent based on the water hardness. Refer
to the instructions on the detergent packaging.
Always use the correct quantity of rinse aid.
Insufficient dosage of rinse aid decreases the
drying results. Using too much rinse aid results
in bluish layers on the items.
Make sure that the water softener level is
correct. If the level is too high, the increased
15
quantity of salt in the water might result in rust
on cutlery.
WHAT TO DO IF YOU WANT TO STOP USING
MULTI-TABLETS
Before you start using separately detergent, salt
and rinse aid, complete the following steps:
1. Set the highest level of the water softener.
2. Make sure that the salt and rinse aid containers
are full.
3. Start the 30 min programme. Do not add
detergent and do not put dishes in the baskets.
4. When the programme is completed, adjust the
water softener according to the water hardness
in your area.
5. Adjust the released quantity of rinse aid.
BEFORE STARTING A PROGRAMME
Before you start the selected programme, make
sure that:
The filters are clean and correctly installed.
The cap of the salt container is tight.
The spray arms are not clogged.
There is enough salt and rinse aid (unless you
use multi-tablets).
The arrangement of the items in the baskets is
correct.
The programme is suitable to the type of load
and the degree of soil.
The correct quantity of detergent is used.
LOADING THE BASKETS
Always use the whole space of the baskets.
Use the appliance to wash dishwasher-safe
items only.
Do not wash in the appliance items made of
wood, horn, aluminium, pewter and copper as
they could crack, warp, get discoloured or
pitted.
Do not wash in the appliance items that can
absorb water (sponges, household cloths).
Put hollow items (cups, glasses and pans) with
the opening facing downwards.
Make sure that glass items do not touch each
other.
Put light items in the upper basket. Make sure
that the items do not move freely.
Put cutlery and small items in the cutlery basket.
Move the upper basket upwards to
accommodate large items in the lower basket.
Make sure that the spray arms can move freely
before you start a programme.
UNLOADING THE BASKETS
1. Let the tableware cool down before you
remove it from the appliance. Hot items can be
easily damaged.
2. First remove items from the lower basket, then
from the upper basket.
After the programme is completed,
water can still remain on the inside
surfaces of the appliance.
CARE AND CLEANING
WARNING! Before any maintenance
other than running the programme
Machine Care, deactivate the
appliance and disconnect the mains
plug from the main socket.
Dirty filters and clogged spray arms
negatively affect the washing results.
Check these elements regularly and, if
necessary, clean them.
MACHINE CARE
Machine Care is a programme designed to clean
the appliance interior with optimal results. It
removes limescale and grease buildup.
When the appliance senses the need for cleaning,
the indicator is on. Start the Machine Care
programme to clean the appliance interior.
How to start the Machine Care programme
Before starting the Machine Care
programme, clean the filters and spray
arms.
1. Use a descaler or a cleaning product designed
specifically for dishwashers. Follow the
instructions on the packaging. Do not put
dishes in the baskets.
2. Press and hold simultaneously Extra Power
and AUTO for about 3 seconds.
The indicators
and Extra Power flash. The
display shows the programme duration.
3. Close the appliance door to start the
programme.
When the programme is complete, the indicator
is off.
16
INTERNAL CLEANING
Carefully clean the appliance, including the
rubber gasket of the door, with a soft damp
cloth.
Do not use abrasive products, abrasive cleaning
pads, sharp tools, strong chemicals, scourer or
solvents.
To maintain the performance of your appliance,
use a cleaning product designed specifically for
dishwashers at least once every two months.
Carefully follow the instructions on the
packaging of the product.
For optimal cleaning results, start the Machine
Care programme.
REMOVAL OF FOREIGN OBJECTS
Check the filters and the sump after each use of the
dishwasher. Foreign objects (e.g. pieces of glass,
plastic, bones or toothpicks, etc) decrease the
cleaning performance and can cause damage to
the drain pump.
1. Disassemble the filters system as instructed in
this chapter.
2. Remove any foreign objects by hand.
CAUTION! If unable to remove the
objects, contact an Authorised
Service Centre.
3. Reassemble the filters as instructed in this
chapter.
EXTERNAL CLEANING
Clean the appliance with a moist soft cloth.
Only use neutral detergents.
Do not use abrasive products, abrasive cleaning
pads or solvents.
CLEANING THE FILTERS
The filter system is made of 3 parts.
1. Turn the filter (B) counterclockwise and remove
it.
2. Remove the filter (C) out of filter (B).
3. Remove the flat filter (A).
4. Wash the filters.
5. Make sure that there are no residues of food or
soil in or around the edge of the sump.
6. Put back in place the flat filter (A). Make sure
that it is correctly positioned under the 2
guides.
17
7. Reassemble the filters (B) and (C).
8. Put back the filter (B) in the flat filter (A). Turn it
clockwise until it locks.
CAUTION! An incorrect position of
the filters can cause bad washing
results and damage to the appliance.
CLEANING THE LOWER SPRAY ARM
We recommend to clean the lower spray arm
regularly to prevent soil from clogging the holes.
Clogged holes can cause unsatisfactory washing
results.
1. To remove the lower spray arm, pull it upwards.
2. Wash the spray arm under running water. Use
a thin pointed tool, e.g. a toothpick, to remove
particles of soil from the holes.
3. To install the spray arm back, press it
downwards.
CLEANING THE UPPER SPRAY ARM
We recommend to clean the upper spray arm
regularly to prevent soil from clogging the holes.
Clogged holes can cause unsatisfactory washing
results.
1. Pull out the upper basket.
2. To detach the spray arm from the basket, press
the spray arm upwards and simultaneously turn
it clockwise.
3. Wash the spray arm under running water. Use
a thin pointed tool, e.g. a toothpick, to remove
particles of soil from the holes.
18
4. To install the spray arm back, press the spray
arm upwards and simultaneously turn it
counterclockwise until it locks into place.
CLEANING THE CEILING SPRAY ARM
We recommend to clean the ceiling spray arm
regularly to prevent soil from clogging the holes.
Clogged holes can cause unsatisfactory washing
results.
The ceiling spray arm is placed on the ceiling of the
appliance. The spray arm (C) is installed in the
delivery tube (A) with the mounting element (B).
C
B
A
1. Move the upper basket to the lowest level to
reach the spray arm more easily.
2. To detach the spray arm (C) from the delivery
tube (A), turn the mounting element (B)
counterclockwise and pull the spray arm
downwards.
3. Wash the spray arm under running water. Use
a thin pointed tool, e.g. a toothpick, to remove
particles of soil from the holes. Run the water
through the holes to wash soil particles away
from the inside.
4. To install the spray arm (C) back, insert the
mounting element (B) in the spray arm and fix it
in the delivery tube (A) by turning it clockwise.
Make sure that the mounting element locks into
place.
19
TROUBLESHOOTING
WARNING! Improper repair of the
appliance may pose a danger to the
safety of the user. Any repairs must be
performed by qualified personnel.
The majority of problems that may occur can
be solved without the need to contact an
Authorised Service Centre.
Refer to the below table for information on possible
problems.
With some problems, the display shows an alarm
code.
Problem and alarm code Possible cause and solution
You cannot activate the appli-
ance.
Make sure that the mains plug is connected to the mains sock-
et.
Make sure that there is no damaged fuse in the fuse box.
The programme does not start. Make sure that the appliance door is closed.
If the delay start is set, cancel the setting or wait for the end of
the countdown.
The appliance recharges the resin inside the water softener.
The duration of the procedure is approximately 5 minutes.
The appliance does not fill with
water.
The display shows i10 or i11.
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low.
For this information, contact your local water authority.
Make sure that the water tap is not clogged.
Make sure that the filter in the inlet hose is not clogged.
Make sure that the inlet hose has no kinks or bends.
The appliance does not drain
the water.
The display shows i20.
Make sure that the sink spigot is not clogged.
Make sure that the interior filter system is not clogged.
Make sure that the drain hose has no kinks or bends.
The anti-flood device is on.
The display shows i30.
Close the water tap.
Make sure that the appliance is correctly installed.
Make sure the baskets are loaded as instructed in the user
manual.
Malfunction of the water level
detection sensor.
The display shows i41 - i44.
Make sure that the filters are clean.
Switch the appliance off and on.
Malfunction of the wash pump
or the drain pump.
The display shows i51 - i59 or
i5A - i5F.
Switch the appliance off and on.
The temperature of the water
inside the appliance is too high
or malfunction of the tempera-
ture sensor occurred.
The display shows i61 or i69.
Make sure that the temperature of the inlet water does not ex-
ceed 60°C.
Switch the appliance off and on.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Zanussi ZDLN7530 Manuel utilisateur

Catégorie
Lave-vaisselle
Taper
Manuel utilisateur

dans d''autres langues