Wacker Neuson RS800A Manuel utilisateur

Taper
Manuel utilisateur

Ce manuel convient également à

Walk-Behind
Rollers
RS 800A
RSS 800A
OPERATOR’S MANUAL
0163165en 003
0910
0163165EN
wc_tx000001gb.fm 3
CALIFORNIA
Proposition 65 Warning:
Engine exhaust, some of its constituents, and certain vehicle
components, contain or emit chemicals known to the State of
California to cause cancer and birth defects or other reproductive
harm.
Foreword
This manual provides information and procedures to safely operate
and maintain this Wacker Neuson model. For your own safety and
protection from injury, carefully read, understand and observe the
safety instructions described in this manual.
Keep this manual or a copy of it with the machine. If you lose this
manual or need an additional copy, please contact Wacker Neuson
Corporation. This machine is built with user safety in mind; however,
it can present hazards if improperly operated and serviced. Follow
operating instructions carefully! If you have questions about operating
or servicing this equipment, please contact Wacker Neuson
Corporation.
The information contained in this manual was based on machines in
production at the time of publication. Wacker Neuson Corporation
reserves the right to change any portion of this information without
notice.
All rights, especially copying and distribution rights, are reserved.
Copyright 2009 by Wacker Neuson Corporation.
No part of this publication may be reproduced in any form or by any
means, electronic or mechanical, including photocopying, without
express written permission from Wacker Neuson Corporation.
Any type of reproduction or distribution not authorized by Wacker
Neuson Corporation represents an infringement of valid copyrights
and will be prosecuted. We expressly reserve the right to make
technical modifications, even without due notice, which aim at
improving our machines or their safety standards.
WARNING
wc_tx000001gb.fm 4
RS 800 Table of Contents
wc_bo0163165en_002TOC.fm 5
Foreword 3
1. Safety Information 7
1.1 Operating Safety .................................................................................. 8
1.2 Operator Safety While Using Internal Combustion Engines ................. 9
1.3 Service Safety .................................................................................... 10
1.4 Label Locations .................................................................................. 11
1.5 Safety Labels ...................................................................................... 12
2. Operation 16
2.1 Operation and Service Locations ....................................................... 16
2.2 Application .......................................................................................... 18
2.3 Recommended Fuel (RS 800A, RSS 800A) ...................................... 18
2.4 Before Starting ................................................................................... 18
2.5 To Start (RS 800A) ............................................................................. 19
2.6 To Stop (RS 800A) ............................................................................. 19
2.7 To Start (RSS 800A) .......................................................................... 20
2.8 To Stop (RSS 800A) ........................................................................... 20
2.9 Direction and Speed Control .............................................................. 21
2.10 Exciter (Vibration) Control .................................................................. 21
2.11 Watering System ................................................................................ 22
2.12 Handle Adjustment ............................................................................. 23
2.13 Operation on Slopes ........................................................................... 24
2.14 Rollovers ............................................................................................ 24
Table of Contents RS 800
wc_bo0163165en_002TOC.fm 6
3. Maintenance 25
3.1 Periodic Maintenance Schedule ..........................................................25
3.2 Lubrication ...........................................................................................26
3.3 Storage ................................................................................................28
3.4 Engine Oil ............................................................................................29
3.5 Air Cleaner ..........................................................................................30
3.6 Spark Plug ...........................................................................................31
3.7 Sediment Cup ......................................................................................31
3.8 Carburetor ...........................................................................................32
3.9 Scraper Bars .......................................................................................33
3.10 Cleaning the Machine ..........................................................................33
3.11 Lifting the Machine ..............................................................................34
3.12 Transporting the Machine ....................................................................35
3.13 Troubleshooting ...................................................................................36
3.14 Wiring Diagram (RSS 800A) ...............................................................38
4. Technical Data 39
4.1 Engine .................................................................................................39
4.2 Roller ...................................................................................................40
4.3 Lubrication ...........................................................................................40
4.4 Dimensions ..........................................................................................41
RS 800 /... Safety Information
wc_si000178gb.fm 7
1. Safety Information
This manual contains DANGER, WARNING, CAUTION, NOTICE, and
NOTE callouts which must be followed to reduce the possibility of
personal injury, damage to the equipment, or improper service.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow this
symbol to avoid possible injury or death.
DANGER indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
NOTICE: Used without the safety alert symbol, NOTICE indicates a
situation which, if not avoided, could result in property damage.
Note: Contains additional information important to a procedure.
DANGER
WARNING
CAUTION
Safety Information RS 800 /...
wc_si000178gb.fm 8
1.1 Operating Safety
Familiarity and proper training are required for the safe operation of the
machine. Machines operated improperly or by untrained personnel
can be hazardous. Read the operating instructions contained in this
manual and the engine manual, and familiarize yourself with the
location and proper use of all controls. Inexperienced operators should
receive instruction from someone familiar with the machine before
being allowed to operate it.
1.1.1 NEVER operate this machine in applications for which it is not
intended.
1.1.2 Do not touch the engine or muffler while the engine is on or
immediately after it has been turned off. These areas get hot and may
cause burns.
1.1.3 Do not use accessories or attachments that are not recommended by
Wacker Neuson. Damage to equipment and injury to the user may
result.
1.1.4 ALWAYS wear protective clothing appropriate to the job site when
operating the machine.
1.1.5 ALWAYS remain aware of moving parts and keep hands, feet, and
loose clothing away from the moving parts of the machine.
1.1.6 Read, understand, and follow procedures in the Operator’s Manual
before attempting to operate the machine.
1.1.7 ALWAYS check that all controls are functioning properly immediately
after start-up! DO NOT operate machine unless all controls operate
correctly.
1.1.8 ALWAYS remain aware of changing positions and movement of other
equipment and personnel on the job site.
1.1.9 ALWAYS remain aware of changing surface conditions and use extra
care when operating over uneven ground, on hills, or over soft or
coarse material. The machine could shift or slide unexpectedly.
1.1.10 ALWAYS use caution when operating near the edges of pits, trenches
or platforms. Check to be sure ground surface is stable enough to
support the weight of the machine and operator and there is no danger
of the machine sliding, falling or tipping.
1.1.11 Always operate machine with all safety devices and guards in place
and in working order. Do not modify or defeat safety devices. Do not
operate machine if any safety devices or guards are missing or
inoperative.
1.1.12 ALWAYS position yourself safely when operating machine in reverse
or on hills. Leave enough space between yourself and the machine so
you will not be placed in a hazardous position should the machine slide
or tip.
WARNING
RS 800 /... Safety Information
wc_si000178gb.fm 9
1.1.13 ALWAYS operate the machine with both of your feet on the ground!
DO NOT stand, sit, or ride on machine while in operation.
1.2 Operator Safety While Using Internal Combustion Engines
Internal combustion engines present special hazards during operation
and fueling. Read and follow the warning instructions in the engine
owner’s manual and the safety guidelines below. Failure to follow the
warnings and safety standards could result in severe injury or death.
1.2.1 Do not smoke while operating the machine.
1.2.2 Do not smoke when refueling the engine.
1.2.3 Do not refuel a hot or running engine.
1.2.4 Do not refuel the engine near an open flame.
1.2.5 Do not run the engine near open flames.
1.2.6 Do not run the machine indoors or in an enclosed area such as a deep
trench unless adequate ventilation, through such items as exhaust
fans or hoses, is provided. Engine exhaust contains carbon monoxide.
This is a poison you cannot see or smell. Exposure to carbon
monoxide can cause loss of consciousness and CAN KILL YOU IN
MINUTES.
1.2.7 Refill the fuel tank in a well-ventilated area.
1.2.8 Replace the fuel tank cap after refueling.
1.2.9 ALWAYS check the fuel lines and the fuel tank for leaks and cracks
before starting the engine. Do not run the machine if fuel leaks are
present or the fuel lines are loose.
1.2.10 ALWAYS keep the area around a hot exhaust pipe free of debris to
reduce the chance of an accidental fire.
WARNING
Safety Information RS 800 /...
wc_si000178gb.fm 10
1.3 Service Safety
A poorly maintained machine can become a safety hazard! In order
for the machine to operate safely and properly over a long period of
time, periodic maintenance and occasional repairs are necessary.
1.3.1 Do not attempt to clean or service the machine while it is running.
Rotating parts can cause severe injury.
1.3.2 DO NOT remove air cleaner cover, paper element, or precleaner while
engine is running.
1.3.3 Do not use gasoline or other types of fuels or flammable solvents to
clean parts, especially in enclosed areas. Fumes from fuels and
solvents can become explosive.
1.3.4 ALWAYS replace the safety devices and guards after repairs and
maintenance.
1.3.5 Replace worn or damaged components with spare parts designed and
recommended by Wacker Neuson Corporation.
1.3.6 Keep the machine clean and labels legible. Replace all missing and
hard-to-read labels. Labels provide important operating instructions
and warn of dangers and hazards.
1.3.7 ALWAYS check all external fasteners at regular intervals.
1.3.8 ALWAYS make sure slings, chains, hooks, ramps, jacks, and other
types of lifting devices are attached securely and have enough weight-
bearing capacity to lift or hold the machine safely. Always remain
aware of the location of other people in the area when lifting the
machine.
1.3.9 Do not crank a flooded engine with the spark plug removed on
gasoline-powered engines. Fuel trapped in the cylinder will squirt out
the spark plug opening.
1.3.10 Do not test for spark on gasoline-powered engines if the engine is
flooded or the smell of gasoline is present. A stray spark could ignite
the fumes.
1.3.11 Keep the area around the muffler free of debris such as leaves, paper,
cartons, etc. A hot muffler could ignite the debris and start a fire.
1.3.12 Disconnect the spark plug on machines equipped with gasoline
engines, before servicing, to avoid accidental start-up.
WARNING
RS 800 /... Safety Information
wc_si000178gb.fm 11
1.4 Label Locations
Safety Information RS 800 /...
wc_si000178gb.fm 12
1.5 Safety Labels
Wacker Neuson machines use international pictorial labels where
needed. These labels are described below.
Label Meaning
DANGER!
Engines emit carbon monoxide; operate only in
well-ventilated area. Read the Operator’s Man-
ual.
No sparks, flames, or burning objects near the
machine. Shut off the engine before refueling.
WARNING!
Hot surface!
CAUTION!
Read and understand the supplied Operator’s
Manual before operating this machine. Failure
to do so increases the risk of injury to yourself
and others.
CAUTION!
Use only clean, filtered diesel fuel.
NOTICE
Lifting point.
RS 800 /... Safety Information
wc_si000178gb.fm 13
WARNING!
To prevent hearing loss, wear hearing protec-
tion when operating this machine.
Tie-down point.
Water Tank
Vibration control ON/OFF.
Control Lever:
Forward and reverse motion controlled by red
levers.
Grease points: Inspect and lubricate every 100
hours of operation.
Label Meaning
Safety Information RS 800 /...
wc_si000178gb.fm 14
Hydrostatic Drive:
Engage / Disengage
A nameplate listing the model number, item
number, revision number, and serial number is
attached to each unit. Please record the infor-
mation found on this nameplate so it will be
available should the nameplate become lost or
damaged. When ordering parts or requesting
service information, you will always be asked
to specify the model number, item number,
revision number, and serial number of the unit.
This machine may be covered by one or more
patents.
Label Meaning
RS 800 /... Safety Information
wc_si000178gb.fm 15
Notes:
Operation RS 800 /...
wc_tx000222gb.fm 16
2. Operation
2.1 Operation and Service Locations
See Graphic: wc_gr003471
RSS 800A
RS 800A
Ref. Description Ref. Description
1 Handle locking pin 7 Exciter control
2 Sprinkler tube 8 Water fill cap
3 Water control valve 9 Fuel tank
4 Scraper bar 10 Lifting eye
5 Tie-down 11 Hydrostatic drive release
6 Forward/reverse control lever 12 Control box
Ref. Description Ref. Description
1 Handle locking pin 7 Exciter control
2 Sprinkler tube 8 Water fill cap
3 Water control valve 9 Fuel tank
4 Scraper bar 10 Lifting eye
5 Tie-down 11 Hydrostatic drive release
6 Forward/reverse control lever
RS 800 /... Operation
wc_tx000222gb.fm 17
12
2
3 4
5
8
9
10
11
6
7
1
wc_gr003471
Operation RS 800 /...
wc_tx000222gb.fm 18
2.2 Application
This machine is designed for compaction of sand, gravel, soil and
asphalt. The RS 800 has tight clearances, making it ideally suited for
small repairs and maintenance of roads, walks, bridges, and parking
lots. The high exciter forces ensure excellent compaction of cohesive-
type soils, as well as loose soils and gravel. The sprinkler system and
water control valve allow the roller to be used wet or dry.
2.3 Recommended Fuel (RS 800A, RSS 800A)
The engine requires regular grade unleaded gasoline. Use only fresh,
clean gasoline. Gasoline containing water or dirt will damage fuel
system. Consult engine owner’s manual for complete fuel
specifications.
2.4 Before Starting
2.4.1 Read and understand the safety and operating instructions at the
beginning of this manual.
2.4.2 Check:
Oil level in the engine
Fuel level
Condition of the air cleaner
Tightness of the external fasteners
Condition of the fuel lines
2.4.1
RS 800 /... Operation
wc_tx000222gb.fm 19
2.5 To Start (RS 800A)
See Graphic: wc_gr000014
2.5.1 Open fuel valve by moving lever to the right (a1).
Note: If engine is cold, move choke lever to close position (b1). If
engine is hot, set choke to open position (b2).
2.5.2 Turn engine switch to “ON” (e1).
2.5.3 Open throttle by moving it slightly to left (d1).
2.5.4 Pull starter rope (c).
Note: If the oil level in the engine is low, the engine will not start. If this
happens, add oil to engine. Some engines are equipped with an oil
alert light (f) that will come on while pulling the starter rope.
2.5.5 Open choke as engine warms (b2).
2.5.6 Open throttle fully to operate.
2.6 To Stop (RS 800A)
See Graphic: wc_gr000014
2.6.1 Reduce engine RPM to idle by moving throttle completely to right (d2).
2.6.2 Turn engine switch to “OFF” (e2).
2.6.3 Close fuel valve by moving lever to the left (a2).
Operation RS 800 /...
wc_tx000222gb.fm 20
2.7 To Start (RSS 800A)
See Graphic: wc_gr003472
2.7.1 Open the fuel valve by moving the lever to the right (a1).
Note: If the engine is cold, move the choke lever to the closed position
(b1). If the engine is hot, set the choke to the open position (b2).
2.7.2 Open the throttle by moving it slightly to left (d2).
2.7.3 Turn and hold the keyswitch in the “START” position (c2) to start the
engine.
DO NOT hold the keyswitch in the “START” position for more than five
seconds. Damage to the starter may result.
Note: If the engine does not start within five seconds, turn the
keyswitch to “OFF”, wait ten seconds, then turn the keyswitch to
“START” again.
2.7.4 When the engine starts, release the keyswitch and allow it to return to
the “ON” position (c1)
2.7.5 Open the choke (b2) as the engine warms.
2.7.6 Place the throttle in the full open position (d3) to operate.
2.8 To Stop (RSS 800A)
See Graphic: wc_gr003472
2.8.1 Reduce the engine RPM to idle by moving the throttle lever completely
to right (d1).
2.8.2 Turn the keyswitch to the “OFF” position (e2).
2.8.3 Close the fuel valve by moving the lever to the left (a2).
CAUTION
d1
d2
wc_gr003472
a2
a1
b1
b2
d1
d3
c3
c1
c2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116

Wacker Neuson RS800A Manuel utilisateur

Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues