Wacker Neuson G625 Manuel utilisateur

Operator’s Manual

Notice d'emploi

Mobile Generator

Groupe électrogène mobile

G625

Type G625

Document 5100027362

Date 0316

Version 01

Language EN-FR

5100027362

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

wc_tx003955gb_FM10.fm

3

Machine Identification

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine Item Number

G625 5100013899

wc_gr012550

Serial Number:

Foreword

4 wc_tx003956gb_FM10.fm

Foreword

Machine

documentation

■ From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

■ Keep a copy of the Operator’s Manual with the machine at all times.

■ For spare parts information, please see your Wacker Neuson Dealer, or visit the

Wacker Neuson website at http://www.wackerneuson.com/.

■ When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

■ This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

■ Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

■ The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change any

portion of this information without notice.

■ The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Foreword

wc_tx003956gb_FM10.fm 5

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

■ Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

■ Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

■ Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

■ Serious injury hazards to the operator and persons in the work area

■ Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Foreword

6 wc_tx003956gb_FM10.fm

Notes

Table of Contents

G625

wc_bo5100027360_01_FM10TOC.fm

7

Foreword 4

1 Safety Information 11

1.1 Signal Words Used in this Manual ..................................................... 11

1.2 Machine Description and Intended Use ............................................. 12

1.3 Safety Guidelines for Operating the Machine ..................................... 13

1.4 Service Safety .................................................................................... 15

1.5 Operator Safety while Using Internal Combustion Engines ............... 17

1.6 Safety Guidelines for Mobile Generators ........................................... 18

1.7 Safety Guidelines for Towing the Machine ......................................... 20

1.8 Safety Guidelines for Lifting the Machine ........................................... 21

1.9 Reporting Safety Defects ................................................................... 21

2 Labels 22

2.1 Label Locations ................................................................................. 22

2.2 Label Meanings .................................................................................. 24

3 Lifting and Transporting 33

3.1 Lifting the Machine ............................................................................. 33

3.2 Before Towing Checklist ..................................................................... 34

3.3 Towing the Machine ........................................................................... 35

3.4 Preparing the Machine for Transport on a Truck or Trailer ................ 36

3.5 Testing the Breakaway System—Electric Brakes .............................. 37

4 Controls 39

4.1 Control and Component Locations ..................................................... 39

4.2 Component Descriptions .................................................................... 41

4.3 Emergency Stop Switch ..................................................................... 44

4.4 Busbar and Camlock Doors ............................................................... 45

4.5 Main Circuit Breaker ........................................................................... 47

4.6 Remote Run Terminal Block .............................................................. 48

4.7 Remote Transfer Switch ..................................................................... 49

4.8 Test Plug Inputs for Voltage ............................................................... 50

4.9 Battery Charger .................................................................................. 50

4.10 Camlocks ............................................................................................ 51

4.11 Containment System .......................................................................... 51

4.12 Three-Way Fuel Valve Switch ............................................................ 52

4.13 Quick Disconnect Fuel Fittings ........................................................... 52

Table of Contents

G625

wc_bo5100027360_01_FM10TOC.fm

8

4.14 Low-Coolant Shutdown .......................................................................53

4.15 Racor Fuel Filtration System ..............................................................54

4.16 Alternator Anti-Condensation Heater ..................................................54

4.17 Coolant Heater ....................................................................................55

5 Using the DSE 8610 Deep Sea Controller 56

5.1 Deep Sea Controller Buttons and Functions ......................................56

5.2 Navigating the Menus .........................................................................59

5.3 How to Reset the Maintenance Timer ................................................62

5.4 Deep Sea Controller Alarms and Shut-Down Conditions ...................63

5.5 Adjusting Screen Contrast ..................................................................65

6 Machine Setup 66

6.1 Preparing the Machine for First Use ...................................................66

6.2 Positioning the Machine ......................................................................67

6.3 Grounding the Generator ....................................................................69

6.4 Recommended Fuel ...........................................................................70

6.5 Connecting and Using an External Fuel Supply .................................71

6.6 Refueling the Machine ........................................................................72

7 How to Connect Loads 74

7.1 Busbar/Camlock Connections and

Voltage Selector Plate Positions .........................................................74

7.2 Connecting Multiple Generators .........................................................76

7.3 Connecting Two Generators ...............................................................78

7.4 Connecting Three Generators ............................................................80

7.5 Connecting Four Generators ..............................................................82

8 Operation 84

8.1 Modes of Operation ............................................................................84

8.2 Configuring the Generator with the Load Application Switch ..............86

8.3 Assigning Generator Position with the

Multi-Set Communication Switch ........................................................87

8.4 Selecting the Voltage ..........................................................................89

8.5 Before Starting the Machine ...............................................................91

8.6 Operating the Generator — Stand-Alone Manual Mode .....................92

8.7 Operating the Generator — Stand-Alone Auto Mode Remote Start ...97

Table of Contents

G625

wc_bo5100027360_01_FM10TOC.fm

9

8.8 Operating the Generator — Multiple Gensets Manual Mode ........... 103

8.9 Operating the Generator — Multiple Gensets

Auto Mode Equal Load Share .......................................................... 109

8.10 Operating the Generator — Multiple Gensets

Auto Mode Load Demand ................................................................ 115

8.11 Operating the Generator — Multiple Gensets

Auto Mode Remote Start .................................................................. 123

8.12 Engine and Generator Monitoring .................................................... 131

9 General Maintenance 132

9.1 Periodic Maintenance Schedule ....................................................... 132

9.2 Maintaining the Emission Control System ........................................ 133

9.3 Preparing for Maintenance ............................................................... 133

9.4 Cleaning the Machine ....................................................................... 133

9.5 Inspecting the Machine .................................................................... 134

9.6 Maintaining the Trailer ...................................................................... 135

9.7 Checking and Pumping Out the Containment System ..................... 136

9.8 Checking the Exhaust System ......................................................... 137

9.9 Maintaining the Battery ..................................................................... 138

9.10 Filling the Radiator ........................................................................... 139

9.11 Storage ............................................................................................. 141

9.12 Machine Disposal and Decommissioning ......................................... 142

10 Engine Maintenance: Volvo TAD1642GE 143

11 Troubleshooting 147

11.1 Responding to a Fluid Accumulation Alarm ..................................... 148

12 Technical Data 149

12.1 Engine .............................................................................................. 149

12.2 Generator ......................................................................................... 150

12.3 Trailer and Skid ................................................................................ 151

12.4 Dimensions ....................................................................................... 152

Tire Safety Information 153

Table of Contents

G625

wc_bo5100027360_01_FM10TOC.fm

10

13 Schematics 165

13.1 Engine Schematic: Volvo TAD1642GE ............................................166

13.2 Schematic Components: Volvo TAD1642GE ...................................167

13.3 Panel Schematic ...............................................................................168

13.4 Schematic Components ....................................................................169

13.5 Panel Schematic Components .........................................................170

13.6 Auxiliary Power Schematic ...............................................................172

13.7 Auxiliary Power Components ............................................................173

13.8 AC Schematic ...................................................................................174

13.9 AC Schematic Components ..............................................................175

13.10 Trailer Wiring ....................................................................................176

13.11 Trailer Wiring Components ...............................................................177

wc_si000928gb_FM10.fm

11

Mobile Generator

Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

► Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

► To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

► To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

► To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000928gb_FM10.fm

12

Mobile Generator

Safety Information

1.2 Machine Description and Intended Use

This machine is a mobile electric power source. The Wacker Neuson Mobile

Generator consists of a trailer-mounted cabinet containing an electric alternator, a

fuel tank, and a diesel engine. A control panel, receptacles, and connection lugs

are provided on the side of the cabinet. Additional connection lugs are provided at

the rear of the cabinet. As the engine runs, the generator converts mechanical

energy into electric power. The operator connects loads to the electric power

receptacles and connection lugs.

This machine is intended for the purpose of supplying electrical power to

connected loads. Refer to the product specifications for the output voltage and

frequency of this generator, and for the maximum output power limit of this

generator.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine, or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

■ Connecting a load that has voltage and frequency requirements that are

incompatible with the generator output

■ Overloading the generator with a load that draws excessive power during either

continuous running or start-up

■ Operating the generator in a manner that is inconsistent with all federal, state

and local codes and regulations

■ Using the machine as a ladder, support, or work surface

■ Using the machine to carry or transport passengers or equipment

■ Using the machine to tow other machines

■ Operating the machine outside of factory specifications

■ Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

■ Heat, noise, exhaust, and carbon monoxide from the engine

■ Fire hazards from improper refueling techniques

■ Fuel and its fumes

■ Electric shock and arc flash

■ Personal injury from improperly lifting the trailer tongue

■ Typical hazards related to towing a trailer on roads and highways

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000928gb_FM10.fm

13

Mobile Generator

Safety Information

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

■ Read and understand the operating instructions contained in all manuals

delivered with the machine.

■ Familiarize yourself with the location and proper use of all controls and safety

devices.

■ Contact Wacker Neuson for additional training if necessary.

When operating this machine:

■ Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

■ have received instruction on how to properly use the machine

■ are familiar with required safety devices

The machine must not be accessed or operated by:

■ children

■ people impaired by alcohol or drugs

Application

area

Be aware of the application area.

■ Keep unauthorized personnel, children, and pets away from the machine.

■ Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

■ Identify whether special hazards exist in the application area, such as toxic

gases or unstable ground conditions, and take appropriate action to eliminate

the special hazards before using the machine.

Be aware of the application area.

■ Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

■ All safety devices and guards are in place and in working order.

■ All controls operate correctly.

■ The machine is set up correctly according to the instructions in the Operator’s

Manual.

■ The machine is clean.

■ The machine’s labels are legible.

To ensure safe operation of the machine:

■ Do not operate the machine if any safety devices or guards are missing or

inoperative.

■ Do not modify or defeat the safety devices.

■ Only use accessories or attachments that are approved by Wacker Neuson.

wc_si000928gb_FM10.fm

14

Mobile Generator

Safety Information

Safe

operating

practices

When operating this machine:

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

When operating this machine:

■ Do not operate a machine in need of repair.

■ Do not consume the operating fluids used in this machine. Depending on your

machine model, these operating fluids may include water, wetting agents, fuel

(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic fluid,

heat transfer fluid (propylene glycol with additives), battery acid, or grease.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

After Use

■ Stop the engine when the machine is not being operated.

■ Close the fuel valve on engines equipped with one when the machine is not

being operated.

■ Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

■ Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

wc_si000928gb_FM10.fm

15

Mobile Generator

Safety Information

1.4 Service Safety

Service

training

Before servicing or maintaining the machine:

■ Read and understand the instructions contained in all manuals delivered with

the machine.

■ Familiarize yourself with the location and proper use of all controls and safety

devices.

■ Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

■ Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

■ Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Precautions

When servicing or maintaining the machine:

■ Read and understand the service procedures before performing any service to

the machine.

■ All adjustments and repairs must be completed before operating the machine.

Do not operate the machine with a known problem or deficiency.

■ All repairs and adjustments shall be completed by a qualified technician.

■ Turn off the machine before performing maintenance or making repairs.

■ Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

■ Re-install the safety devices and guards after repair and maintenance

procedures are complete.

Machine

modifications

When servicing or maintaining the machine:

■ Use only accessories/attachments that are approved by Wacker Neuson.

When servicing or maintaining the machine:

■ Do not defeat safety devices.

■ Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

■ Replace worn or damaged components.

■ Replace all missing and hard-to-read labels.

■ When replacing electrical components, use components that are identical in

rating and performance to the original components.

■ When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

Cleaning

When cleaning and servicing the machine:

■ Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

■ Keep the labels legible.

When cleaning the machine:

wc_si000928gb_FM10.fm

16

Mobile Generator

Safety Information

■ Do not clean the machine while it is running.

■ Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

In addition, before servicing or maintaining the machine:

■ Tie back long hair.

■ Remove all jewelry (including rings).

Electrical

service safety

■ Make sure clothing and shoes are dry, stand on a dry wooden platform or rubber

insulating mat, and use tools with insulated handles when servicing the

machine.

■ Do not allow water to accumulate around the base of the machine. If water is

present, move the machine and allow the machine to dry before servicing.

■ Do not pressure wash the control panel, generator end, or any other electrical

components when cleaning the machine.

Cooling

system safety

■ Do not attempt to open the radiator cap while the unit is running or before the

engine has cooled down. Severe burns may result!

■ Engine coolant is toxic to humans and animals. Clean up spills and dispose of

waste engine coolant in accordance with local environmental regulations.

wc_si000928gb_FM10.fm

17

Mobile Generator

Safety Information

1.5 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

■ Keep the area around the exhaust pipe free of flammable materials.

■ Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

■ Do not smoke while operating the machine.

■ Do not run the engine near sparks or open flames.

■ Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

■ Do not operate a machine when its fuel cap is loose or missing.

■ Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

■ Clean up any spilled fuel immediately.

■ Refill the fuel tank in a well-ventilated area.

■ Re-install the fuel tank cap after refueling.

■ Use suitable tools for refueling (for example, a fuel hose or funnel).

When refueling the engine:

■ Do not smoke.

■ Do not refuel a hot or running engine.

■ Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

► Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

► NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through items such as exhaust fans or hoses.

wc_si000928gb_FM10.fm

18

Mobile Generator

Safety Information

1.6 Safety Guidelines for Mobile Generators

Installing as

backup power

Special hazards exist when installing this machine as a backup power supply.

Improper connection of generator to a building’s electrical system can allow

electrical current from the generator to backfeed into utility lines. This may result in

electrocution of utility workers, fire, or explosion.

If connected to a building’s electrical system, the generator must meet the power,

voltage, and frequency requirements of the equipment in the building. Differences

in power, voltage, and frequency requirements may exist and improper connection

may lead to equipment damage, fire, and personal injury or death.

DANGER

Carbon monoxide. Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide (CO). This is a poison you cannot

see or smell. If you can smell the generator exhaust, you are breathing CO. Even if

you cannot smell the exhaust, you could be breathing CO.

► NEVER use a generator inside homes, garages, crawlspaces, or other partly

enclosed areas. Deadly levels of carbon monoxide can build up in these areas.

Using a fan or opening windows and doors does NOT supply enough fresh air.

► ONLY use a generator outside and far away from windows, doors, and vents.

These openings can pull in generator exhaust.

► Even when you use a generator correctly, CO may leak into the home. ALWAYS

use a battery-powered or battery-backup CO alarm in the home.

► If you start to feel sick, dizzy, or weak after the generator has been running,

move to fresh air RIGHT AWAY. See a doctor. You could have carbon monoxide

poisoning.

WARNING

Electrocution hazard. Machines that generate electric power present special

hazards while the engine is running. These include the risk of electrocution or

severe electrical shock.

► Read and follow the instructions in this Operator’s Manual.

WARNING

Backfeed from the generator into the public power distribution system can cause

serious injury or death to utility workers!

► Connections to a building’s electrical system must be made by a qualified

electrician and comply with all applicable laws and electrical codes.

wc_si000928gb_FM10.fm

19

Mobile Generator

Safety Information

General safety

■ Do not use evaporative starting fluids to start the engine. They are highly

explosive.

■ Do not store items such as excess oil, rags, or tools on top of or inside the

machine. These items are a fire hazard and can restrict cooling air.

■ Ensure that electrical cords attached to the machine are in serviceable condition

without cuts, cracks, or exposed wires.

■ Do not route electrical cords over vibrating or hot parts of the machine.

■ Do not stand on the machine.

■ Do not enclose or cover the machine when it is use, or when it is hot.

Ground

connection

The generator must be connected to a good earthen ground for proper operating

safety.

A central “equipment ground” is provided at the customer connection lugs. This

point is connected directly to the generator set base. All other system grounds are

connected to this central point. Ground the generator in accordance with the

standards defined in national, state, and local regulations.

wc_si000928gb_FM10.fm

20

Mobile Generator

Safety Information

1.7 Safety Guidelines for Towing the Machine

When towing the machine:

■ Do not tow the machine if the towing vehicle’s hitch or the trailer’s coupler are

damaged.

■ Do not tow the machine if any of the trailer’s lug nuts are missing.

■ Do not tow the machine if the trailer’s tires have less than 1/16 inch (1.5 mm) of

tread.

■ Do not tow the machine unless the trailer’s brakes are functioning properly.

■ Do not exceed the trailer manufacturer’s speed limitations.

When towing the machine:

■ Only tow the machine when the trailer’s lug nuts are properly torqued.

■ Only tow the machine when the trailer’s tires are properly inflated.

■ Only tow the machine when all trailer lights are functioning correctly.

■ Only tow the machine when the trailer’s safety chains are connected to the

towing vehicle in a crisscross pattern.

■ Maintain extra distance between the towing vehicle and other vehicles.

■ Avoid soft shoulders, curbs, and sudden lane changes.

■ Abide by all licensing requirements for your area.

If you have not driven a towing vehicle with a trailer before, practice turning,

stopping, and backing up the towing vehicle with the trailer in an area away from

traffic. Only drive the towing vehicle with the trailer when you are confident in your

ability to do so.

WARNING

Risk of severe injury or death. Improper trailer condition and towing technique can

lead to an accident.

► Obey the trailer manufacturer’s instructions and the instructions below to reduce

the risk of an accident.

La page charge ...

Wacker Neuson G625 Manuel utilisateur

Wacker Neuson G625 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents