Wacker Neuson LTE4K Manuel utilisateur

Taper
Manuel utilisateur
Operator’s Manual
Light Tower
LTE
50 Hz
Type LTE4K
Document 5100042485
Date
0919
Revision
02
Language EN
Copyright notice
© Copyright 2019 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original instructions
This Operators Manual presents the original instructions. The original
language of this Operator’s Manual is American English.
LTE Foreword
wc_tx004584en.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machines
covered in
this manual
Machine
identification
Information regarding the machine model, code, and year of production is on the
unit serial number plate. Always quote the machine model and serial number when
contacting your dealer, the factory, and for any spare parts requests. All of our
products comply with CE requirements. They conform to directives and fulfill all the
relevant safety requirements.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
For spare parts information, please see your Wacker Neuson Dealer, or visit
the Wacker Neuson website at http://www.wackerneuson.com/.
When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Machine Item Number
LTE4K 5100042190, 5100042191, 5100051617
9
wc_gr014735
Serial Number:
Foreword LTE
4 wc_tx004584en.fm
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change
any portion of this information without notice.
The illustrations, parts, and procedures in this manual refer to Wacker Neuson
factory-installed components. Your machine may vary depending on the
requirements of your specific region.
Manufacturers
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following
consequences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
EC DECLARATIONOFCONFORMITY
TrimeSpa
RegisteredofficeinStradaperRobecco,snc,20081CassinettadiLugagnano(MI),Italy
Declareunderourresponsibilitythatthemachinenamed
WackerNeuson
LTE4K
Iscompliantwiththesafetyrequirementscontainedinthe
EECdirective2006/42
Andthatitwasbuiltinfullcomplianceoftheharmonizedstandards:
ENISO121001
ENISO121002
CEIEN602041
2000/14/ECNoise
2014/30/EU
EN6059825
ISO85288
CassinettadiLugagnano FactoryManager:
AndreaFontanella
Table of Contents
LTE
wc_bo5100042485_02TOC.fm
7
Foreword 3
EC Declaration of Conformity 5
1 Safety Information 9
1.1 Signal Words Used in this Manual ............................................................... 9
1.2 Machine Description and Intended Use ..................................................... 10
1.3 Safety Guidelines for Operating the Machine ............................................. 11
1.4 Service Safety ............................................................................................ 14
1.5 Operator Safety while Using Internal Combustion Engines ....................... 17
1.6 Safety Guidelines for Lifting the Machine ................................................... 18
1.7 Safety Guidelines for Towing the Machine ................................................. 18
2 Labels 20
2.1 Label Locations .......................................................................................... 20
2.2 Label Meanings .......................................................................................... 20
3 Lifting and Transporting 22
3.1 Transport and Handling with Crane ............................................................ 22
3.2 Transport and Handling with Forklift ........................................................... 23
3.3 Adjustable Trailer Hitch (Optional) ............................................................. 24
3.4 Positioning and Uncoupling ........................................................................ 25
4 Operation 26
4.1 Preparing the Machine for First Use ........................................................... 26
4.2 Positioning the Machine ............................................................................. 26
4.3 Stabilizing the Unit ...................................................................................... 28
4.4 Directing and Using the Lights ................................................................... 29
4.5 Preliminary Check and Starting .................................................................. 30
4.6 Machine Components ................................................................................ 31
4.7 Automatic Mast Operating Safety System .................................................. 33
4.8 DSE 3110 Module: Description of Controls ................................................ 34
4.9 DSE 3110 Module: Protections .................................................................. 35
4.10 DSE 3110 Module: Icons ............................................................................ 36
4.11 DSE 3110 Module: Viewing the Instruments .............................................. 37
4.12 Operation in Manual Mode ......................................................................... 38
4.13 Operation in Auto Mode ............................................................................. 39
Table of Contents
LTE
wc_bo5100042485_01TOC.fm
8
5 Maintenance 40
5.1 Routine Maintenance ..........................................................................40
5.2 Long-Term Storage .............................................................................41
5.3 Disposal and Decommissioning ..........................................................42
6 Engine Maintenance: KUBOTA Z482 43
7 Technical Data 47
7.1 Floodlights ...........................................................................................47
7.2 Mast .....................................................................................................47
7.3 Engine .................................................................................................48
7.4 Generator ............................................................................................48
7.5 Machine ...............................................................................................49
7.6 Sound Measurements .........................................................................49
7.7 Radiation Compliance .........................................................................49
7.8 Dimensions ..........................................................................................50
8 Schematics—LTE4K 51
8.1 Electrical Schematic ............................................................................52
8.2 Electrical Schematic Components .......................................................53
9 Schematics—LTE4K AMOSS 56
9.1 Electrical Schematic ............................................................................56
9.2 Electrical Schematic Components .......................................................57
10 Appendix: Time Switch Instruction Manual 61
wc_si001099en.fm
9
LTE Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si001099en.fm
10
Safety Information LTE
1.2 Machine Description and Intended Use
Machine
description
This machine is a mobile, trailer-mounted light tower. The Wacker Neuson Light
Tower consists of a trailer with a cabinet containing a diesel engine, a fuel tank, a
control panel, and an electric alternator. A telescoping tower with six LED lights is
vertically mounted to the top of the cabinet. As the engine runs, the generator
converts mechanical energy into electric power. The LED lights run off this power.
Receptacle(s) are also provided to power auxiliary loads. The operator uses the
control panel to operate and monitor the machine.
Intended use
This machine is intended for the illumination of outdoor areas. This machine is also
intended for the purpose of supplying electrical power to connected loads. Refer to
the machine specifications for the output voltage and frequency, and for the
maximum output power limit of this machine.
This machine has been designed and built strictly for the intended use described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty. The following are some
examples of misuse:
Connecting a load that has voltage and frequency requirements that are
incompatible with the machine output
Overloading the machine with a device that draws excessive power during
either continuous running or start-up
Operating the machine in a manner that is inconsistent with all federal, state,
and local codes and regulations
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Using the machine to tow other machines (unless factory equipped)
Using the machine as a hoist, or hanging items from the tower
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
Heat, noise, exhaust, and carbon monoxide from the engine
Heat from the lights
Ultraviolet radiation from the lights
Fire hazards from improper refueling techniques
Fuel and its fumes
Electric shock and arc flash
Personal injury from improper lifting the trailer tongue
Glare from lights (lights may blind drivers of nearby motor vehicles if the lights
are incorrectly positioned)
wc_si001099en.fm
11
LTE Safety Information
Typical hazards related to towing a trailer on roads and highways
To protect yourself and others, make sure you thoroughly read and understand
the safety information presented in this manual before operating the machine.
1.3 Safety Guidelines for Operating the Machine
Operator
training
Before operating the machine:
Read and understand the operating instructions contained in all manuals
delivered with the machine.
Familiarize yourself with the location and proper use of all controls and safety
devices.
Contact Wacker Neuson for additional training if necessary.
When operating this machine:
Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
Have received instruction on how to properly use the machine
Are familiar with required safety devices
The machine must not be accessed or operated by:
Children
People impaired by alcohol or drugs
Application
area
Be aware of the application area.
Keep unauthorized personnel, children, and pets away from the machine.
Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
Identify whether special hazards exist in the application area, such as toxic
gases or unstable ground conditions, and take appropriate action to eliminate
the special hazards before using the machine.
Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
Safety
devices,
controls, and
attachments
Only operate the machine when:
All safety devices and guards are in place and in working order.
All controls operate correctly.
The machine is set up correctly according to the instructions in the Operator’s
Manual.
The machine is clean.
The machine’s labels are legible.
To ensure safe operation of the machine:
Do not operate the machine if any safety devices or guards are missing or
inoperative.
wc_si001099en.fm
12
Safety Information LTE
Do not modify or defeat the safety devices.
Only use accessories or attachments that are approved by Wacker Neuson.
Safe
operating
practices
When operating this machine:
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
Do not operate a machine in need of repair.
Fire
precautions
Clean all dirt, oil, and other fluids from components to minimize fire risks and aid
in spotting loose or leaking components.
Check the engine for oily rags or other debris that could be a potential cause of
fire before starting the unit.
Have a fire extinguisher nearby. Be sure the extinguisher is properly maintained
and be familiar with its use.
In the event of a fire, use one of the following: carbonate anhydride (or carbon
dioxide), powder, foam, or water spray. Avoid using water jets.
In the event of a fire, wear a breathing apparatus if there is heavy smoke.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while operating this
machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
Before
starting
Be sure the machine is on a firm, level surface and will not tip, roll, slide, or fall
while operating.
Never connect machine to other power sources, such as supply mains of power
companies.
Never use the machine if the insulation on the electrical cord is cut or worn
through.
Never raise the tower or operate the machine in high winds.
The tower extends up to 8.5 m (27.9 ft.). Make sure the area above the trailer is
open and clear of overhead wires and obstructions.
Know all side clearance and overhead obstructions for safe operation of the
machine.
Check that winch cables are in good condition and are centered on each pulley.
Do not start the engine or operate any control if there is a ‘DO NOT OPERATE’
or similar warning sign attached to any control.
Use jumper cables only as recommended. Improper use can result in battery
explosion.
Operation
For operators’ safety, the grounding of the machine always needs to be done
paying attention on the section of the cable to be used (never to be less than
10 mm
2
). For the connection of the grounding cable, please always use the clip
located on the front/right angle of the machine, near the jack.
wc_si001099en.fm
13
LTE Safety Information
Keep the area under and around the lights clear of people while raising and
lowering the tower.
The machine must be leveled and outriggers extended before raising the tower.
Do not move the Light Tower while it is operating or while the tower is raised.
Before carrying out any welding on the machine, ALWAYS make sure to
disconnect batteries and alternator leads.
The tools must NOT come into contact with the battery terminals with the risk of
creating an electric arc.
Use jumper cables only as recommended. Improper use can result in severe
damage and safety risk.
Do not operate lights without protective lens cover in place or with a lens cover
that is cracked or damaged.
After use
Stop the engine when the machine is not being operated.
Close the fuel valve on engines equipped with one when the machine is not
being operated.
Ensure that the machine will not tip over, roll, slide, or fall when not being
operated.
Store the machine properly when it is not being used. The machine should be
stored in a clean location out of the reach of children.
Lower the tower when not in use, or if high winds or electrical storms are
expected in the area.
The lamps become extremely hot in use! Allow the lamp and fixture to cool 10–
15 minutes before handling.
wc_si001099en.fm
14
Safety Information LTE
1.4 Service Safety
Service
training
Before servicing or maintaining the machine:
Read and understand the instructions contained in all manuals delivered with
the machine.
Familiarize yourself with the location and proper use of all controls and
protective devices.
Only trained personnel shall troubleshoot or repair problems occurring with the
machine.
Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
Do not allow untrained or improperly trained people to service or maintain the
machine. Personnel servicing or maintaining the machine must be familiar with
the associated potential risks and hazards.
Precautions
When servicing or maintaining the machine:
Read and understand the service procedures before performing any service to
the machine.
All adjustments and repairs must be completed before operating the machine.
Do not operate the machine with a known problem or deficiency.
All repairs and adjustments shall be completed by a qualified technician.
Turn off the machine before performing maintenance or making repairs.
Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
Reinstall the safety devices and guards after repair and maintenance
procedures are complete.
Allow only authorized and trained personnel to service and maintain the
machine. Please read the operator’s handbook and service manual before
operating or servicing the machine.
HIGH VOLTAGE! This equipment utilizes high voltage circuits. Always exercise
extreme caution when trouble shooting or repairing any electrical circuit.
Only a qualified electrician should troubleshoot or repair electrical problems
occurring on the machine.
Before servicing the lighting tower, ensure that the engine start switch is turned
to OFF.
Disconnect electrical power and turn off engine before removing protective
covers on high voltage electrical closures.
NEVER perform even routine service (oil/filter changes, cleaning, etc.) if all
electrical components aren’t shut down.
NEVER allow water to accumulate at the base of the machine. If water is
present, DO NOT service!
DO NOT service electrical components if your clothing or skin is wet.
wc_si001099en.fm
15
LTE Safety Information
If the unit is stored outside, check the engine and generator for any moisture. If
wet, dry the unit thoroughly before starting.
Never wash the unit with a high pressure hose or with any kind of power washer.
Open main circuit breaker before disconnecting battery cables.
Ensure to always relieve pressure before servicing any pressurized system.
Be aware of hot exhaust pipes and engine.
KEEP AWAY from moving parts on generator and engine. Be aware of the
hazard if you wear loose clothing.
Check and replace all missing and hard-to-read labels.
Make sure slings, chains, hooks, ramps, jacks, and other types of lifting devices
are attached securely and have enough weight-bearing capacity to lift or hold
the equipment safely.
Before servicing the Light Tower, make sure the engine start switch is turned to
the OFF position, the circuit breakers are open (off), and the negative terminal
on battery is disconnected. Do not perform even routine service (oil/filter
changes, cleaning, etc.) unless all electrical components are shut down.
Always turn off light circuit breakers and shut down engine before disconnecting
light fixtures or changing light bulbs.
Machine
modifications
When servicing or maintaining the machine:
Use only accessories/attachments that are approved by Wacker Neuson.
Do not defeat safety devices.
Do not modify the machine without the express written approval of Wacker
Neuson.
Replacing
parts and
labels
Replace worn or damaged components.
Replace all missing and hard-to-read labels.
When replacing electrical components, use components that are identical in
rating and performance to the original components.
When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.
Cleaning
When cleaning and servicing the machine:
Keep machine clean and free of debris such as leaves, paper, cartons, etc.
Keep labels legible.
Clean with soapy water only.
When cleaning the machine:
Do not clean the machine while it is running.
Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.
wc_si001099en.fm
16
Safety Information LTE
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while servicing or
maintaining this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair.
Remove all jewelry (including rings).
wc_si001099en.fm
17
LTE Safety Information
1.5 Operator Safety while Using Internal Combustion Engines
Operating
safety
When running the engine:
Keep the area around the exhaust pipe free of flammable materials.
Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine. Do not run the machine if fuel leaks are present or the fuel lines are
loose.
Do not smoke while operating the machine.
Do not run the engine near sparks or open flames.
Do not touch the engine or muffler while the engine is running or immediately
after it has been turned off.
Do not operate a machine when its fuel cap is loose or missing.
Do not start the engine if fuel has spilled or a fuel odor is present. Move the
machine away from the spill and wipe the machine dry before starting.
Do not use the machine in areas with risk of explosion or fire.
Refueling
safety
When refueling the engine:
Clean up any spilled fuel immediately.
Refill the fuel tank in a well-ventilated area.
Reinstall the fuel tank cap after refueling.
Use suitable tools for refueling (for example, a fuel hose or funnel).
Do not smoke.
Do not refuel a hot or running engine.
Do not refuel the engine near sparks or open flames.
Take due care when working with fuel. Diesel fuel is a health hazard. Be aware
that there is also danger of fire and pollution.
Unscrew the fuel tank cap slowly to let out the fuel vapors.
Do not fill the tank completely and wipe up spilled fuel before starting engine.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Exhaust gas from the engine contains carbon monoxide, a deadly poison.
Exposure to carbon monoxide can kill you in minutes.
NEVER operate the machine inside an enclosed area, such as a tunnel, unless
adequate ventilation is provided through items such as exhaust fans or hoses.
wc_si001099en.fm
18
Safety Information LTE
1.6 Safety Guidelines for Lifting the Machine
When lifting the machine:
Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any
other type of lifting device used is attached securely and has enough weight-
bearing capacity to lift or hold the machine safely. See section Technical Data
for machine weight.
Remain aware of the location of other people when lifting the machine.
Only use the lifting points and tie-downs described in the Operator’s Manual.
Make sure the transporting vehicle has sufficient load capacity and platform size
to safely transport the machine.
To reduce the possibility of injury:
Do not stand under the machine while it is being lifted or moved.
Do not get onto the machine while it is being lifted or moved.
1.7 Safety Guidelines for Towing the Machine
When towing the machine:
Do not tow the machine if the towing vehicle’s hitch or the trailers coupler are
damaged.
Do not tow the machine if safety chains are damaged.
Do not tow the machine if any of the trailer’s lug nuts are loose or missing.
Do not tow the machine if the trailer’s tires have less than 1/16 inch (1.5 mm) of
tread.
Do not tow the machine if trailer tires are underinflated.
Do not tow the machine unless the trailer’s brakes are functioning properly.
Do not tow the machine if trailer lighting is not functioning properly.
Do not exceed the trailer manufacturer’s speed limitations of 75 km/h.
Recommended maximum off-road towing speed is 15 km/h (less on uneven
terrain).
Only tow the machine when the trailer’s lug nuts are properly torqued.
Only tow the machine when the trailers tires are properly inflated.
Only tow the machine when all trailer lights are functioning correctly.
Only tow the machine when the trailer’s safety chains are connected to the
towing vehicle in a crisscross pattern.
Maintain extra distance between the towing vehicle and other vehicles.
Avoid soft shoulders, curbs, and sudden lane changes.
Abide by all licensing requirements for your area.
WARNING
Risk of severe injury or death. Improper trailer condition and towing technique can
lead to an accident.
Obey the instructions below to reduce the risk of an accident.
wc_si001099en.fm
19
LTE Safety Information
If you have not driven a towing vehicle with a trailer before, practice turning,
stopping, and backing up the towing vehicle with the trailer in an area away from
traffic. Only drive the towing vehicle with the trailer when you are confident in your
ability to do so.
wc_si001100en.fm
20
Labels LTE
2 Labels
2.1 Label Locations
2.2 Label Meanings
wc_gr014841
A
B
D
E
G
H
J
F
D
C
A
Attention
Read the operator’s manual before operating the
machine.
B
Attention
High voltage.
Read the operator’s manual before operating the
machine.
C
Do not extinguish with water.
Attention
Do not touch the moving parts.
D
Attention
Danger of crushing.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66

Wacker Neuson LTE4K Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues