Extron HD 4K 101 Plus Manuel utilisateur
- Taper
- Manuel utilisateur
68-2892-01 Rev. C
01 19
HD 4K 101 Plus
User Guide
HDMI
Cable Equalizer
Safety Instructions • English
WARNING: This symbol,
D
, when used on the product, is intended
to alert the user of the presence of uninsulated dangerous voltage
within the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol,
I
, when used on the product, is
intended to alert the user of important operating and maintenance
(servicing) instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme,
D
, lorsqu’il est utilisé sur
le produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de provoquer
un choc électrique.
ATTENTION : Ce pictogramme,
I
, lorsqu’il est utilisé sur
le produit, signale à l’utilisateur des instructions d’utilisation ou de
maintenance importantes qui se trouvent dans la documentation
fournie avec le matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron,
réf. 68-290-01, sur le site Extron, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol
D
auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind
und die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol
I
auf dem Produkt soll dem Benutzer
in der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie
in den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68-290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo,
D
, cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo,
I
, cuando se utiliza en el producto,
avisa al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con el
equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron,
www.extron.com.
Инструкция по технике безопасности • Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ,
D
, если указан
на продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим
током.
ВНИМАНИЕ: Данный символ,
I
, если указан на продукте,
предупреждает пользователя о наличии важных инструкций по
эксплуатации и обслуживанию в руководстве, прилагаемом к
данному оборудованию.
Для получения информации о правилах техники безопасности,
соблюдении нормативных требований, электромагнитной
совместимости (ЭМП/ЭДС), возможности доступа и других вопросах
см. руководство по безопасности и соблюдению нормативных
требований Extron на сайте Extron: www.extron.com, номер по
каталогу - 68-290-01.
安全说明 • 简体中文
警告： D产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压，
有触电危险。
注意：I 产品上的这个标志意在提示用户设备随附的用户手册中有
重要的操作和维护(维修）说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
使用的特性等相关内容，敬请访问 Extron 网站 www.extron.com，参见 Extron
安全规范指南，产品编号 68-290-01。
安全記事 • 繁體中文
警告: D 若產品上使用此符號，是為了提醒使用者，產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意I 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊中有重要
的操作和維護（維修）説明。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細資訊，
請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安全性與法規遵守手
冊》，準則編號 68-290-01。
安全上のご注意
• 日本語
警告: この記号 D が製品上に表示されている場合は、筐体内に絶縁されて
いない高電圧が流れ、感電の危険があることを示しています。
注意:この記号 I が 製 品 上 に 表 示 さ れ て い る 場 合 は 、本 機 の 取 扱 説 明 書 に 記 載 さ れ て
いる重要な操作と保守(整備)の指示についてユーザーの注意を喚起するものです。
安全上のご注意、法令遵守、EMI/EMF適合性、その他の関連項目に
つ い て は 、エ ク スト ロ ン の ウ ェ ブ サ イト www.extron.com より
『Extron Safety and Regulatory Compliance Guide』 (P/N 68-290-01) をご覧く
ださい。
안전 지침 • 한국어
경고: 이 기호 D, 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의: 이 기호 I, 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에 대한
자세한 내용은 Extron 웹 사이트(www.extron.com)의 Extron 안전 및 규제 준수
안내서, 68-290-01 조항을 참조하십시오.
Safety Instructions
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part15 of the FCC rules. The ClassA limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference. This interference must be corrected at the expense of the user.
NOTE: For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the “Extron Safety and Regulatory
Compliance Guide
” on the Extron website.
Copyright
© 2016
-2019 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks
®
, registered service marks
(SM)
, and trademarks
(TM)
are the property of
RGBSystems, Inc. or Extron Electronics:
Registered Trademarks
(®)
Extron, AVTrac, Cable Cubby, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Flat Field, FlexOS, Global Configurator, GlobalViewer,
Hideaway, Inline, IPIntercom, IPLink, KeyMinder, LinkLicense, LockIt, MediaLink, NetPA, PlenumVault, PoleVault, PowerCage, PURE3,
Quantum, SoundField, SpeedMount, SpeedSwitch, SystemINTEGRATOR, TeamWork, TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift,
WallVault, WindoWall, XTP, and XTPSystems
Registered Service Mark
(SM)
: S3 Service Support Solutions
Trademarks
(
™
)
AAP, AFL (Accu-RateFrameLock), ADSP(Advanced Digital Sync Processing), Auto-Image, CableCover, CDRS(ClassD Ripple Suppression),
DDSP(Digital Display Sync Processing), DMI (DynamicMotionInterpolation), DriverConfigurator, DSPConfigurator, DSVP(Digital
Sync Validation Processing), eLink, EQIP, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, ProDSP,
QS-FPC(QuickSwitch Front Panel Controller), Room Agent, Scope-Trigger, ShareLink, SIS, SimpleInstructionSet, Skew-Free, SpeedNav,
T
riple-Action Switching, True4K, Vector™ 4K , WebShare, XTRA, ZipCaddy, ZipClip
Conventions Used in this Guide
Notifications
In this user guide, the following are used:
WARNING: Potential risk of severe injury or death.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.
ATTENTION:
• Risk of property damage.
• Risque de dommages matériels.
NOTE: A note draws attention to important information.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at http://www.extron.com/technology/glossary.aspx.
Contents
Introduction............................................................ 1
About the HD 4K 101 Plus ................................. 1
Features ............................................................. 2
Panel Features ...................................................... 3
HD 4K 101 Plus Front Panel ............................... 3
Input Cable Lengths ....................................... 3
Securing the HDMI Connector ........................ 4
HD 4K 101 Plus Rear Panel ................................ 5
Powering Via the Input Source ........................ 7
Internal Settings .................................................. 7
Connecting for Long Cable Runs ........................ 9
Mounting ............................................................... 10
Tabletop Mounting ............................................ 10
Rack Mounting ................................................. 10
Underwriters Laboratories Guidelines for
Rack Mounting ............................................. 10
Rack Mounting the HD 4K 101 Plus ............. 10
Under Desk Mounting ....................................... 10
Through Desk Mounting ................................... 10
Extron Warranty .................................................. 11
HD 4K 101 Plus • Contents v
Introduction
This guide describes the function, installation, and operation of the HD 4K 101 Plus cable
equalizer. Unless otherwise stated, the term “cable equalizer” refers to this product.
This section provides the following information:
• About the HD 4K 101 Plus
• Features
About the HD 4K 101 Plus
The HD 4K 101 Plus is a cable equalizer that actively conditions incoming HDMI signals
to compensate for signal loss when using long HDMI cables, low quality HDMI cables, or
source devices with poor HDMI signal output. It extends Ultra High Definition (UHD) and
4K signals up to 50 feet (15 m).
HDMI IN
HDMI OUT
HD 4K 101 Plus
POWER
12V
--A MAX
MODEL 80
PC
4K/60Hz Output
4K Display
Extron
HD 4K 101 Plus
HDMI Cable Equalizer
for Ultra HD
and 4K Sources
Extron
HDMI Pro Series Cable
Short HDMI
Cable
Figure 1. HD 4K 101 Plus Application Diagram
The HD 4K 101 Plus supports resolutions up to UHD (3840x2160@ 60Hz) or
4K (4096x2160@ 60Hz). It is also able to support a 225 MHz pixel clock rate with
1080p @ 60Hz (8, 10, or 12-bit) or 1920x1200 @ 60 Hz resolution.
HD 4K 101 Plus • Introduction 1
The HD 4K 101 Plus also passes Extended Display Identification Data (EDID) information
and supports the long distance transmission of HDTV signals with High-bandwidth Digital
Content Protection (HDCP) for copy protection of digital television broadcasts and high
resolution digital video output from DVD, HD DVD, and Blu-ray Disc™ players.
With the appropriate adapters from Extron, the HD 4K 101 Plus is fully compatible with all
Extron HDMI and DVI products that support both 1080p@ 60Hz and UHD and
4K @ 60 Hz resolutions.
Features
• Supports UHD and 4K signals — The HD 4K 101 Plus supports computer video
resolutions up to 2560x1600, HDTV 1080p/60 Deep Color, UHD resolutions at
3840x2160@ 60Hz (4:4:4) and 4K resolutions 4096x 2160 @ 60 Hz (4:4:4).
• HDCP compliant — The HD 4K 101 Plus supports HDCP 1.4 and 2.2.
• Supports pixel clocks up to 600 MHz — The HD 4K 101 Plus handles up to 600
Mhz pixel clock to ensure compatibility with HDMI 2.0.
• Supports HDMI specifications — The HD 4K 101 Plus supports data rates up to
18.0 Gbps, Deep Color up to 12-bit, 4K, 3D, Lip Sync, HD lossless audio formats,
and CEC.
• Extends UHD and 4K video signals up to 50 feet (15m) over HDMI cable.
• Automatic input cable equalization — The HD 4K 101 Plus actively conditions
incoming HDMI signals to compensate for signal loss when using long HDMI cables, low
quality HDMI cables, and source devices with poor HDMI signal output.
• DDC and HDCP copy protection transmission support — Display Data Channel
(DDC) allows pass-through of EDID and HDCP information between source and display.
• Pass through EDID communication and HDCP key exchange between the
display and source — The HD 4K 101 Plus passes Extended Display Identification
Data (EDID) information and supports the long distance transmission of HDTV signals
with High-bandwidth Digital Content Protection (HDCP) for copy protection.
• Input — One HDMI connector.
• Output — One HDMI connector.
• LockIt HDMI cable lacing brackets included — LockIt lacing brackets are used to
secure HDMI cables connected to the HDMI input and output connectors, preventing
accidental disconnection of the cables.
• LED indicator for source signal presence and power — Indicator illuminates amber
when power is detected and green when a signal is present.
• Can be powered directly from the HDMI source device — Attached source devices
that provide +5 VDC on the HDMI output can power the HD 4K 101 Plus, eliminating the
need for power supply installation.
• Enclosure — Compact 1 inch (2.5 cm) high, 1/8 rack wide, 3 inch deep enclosure.
• Rack and furniture mounting — The cable equalizer can be mounted on a rack shelf or
under a desk or podium using optional mounting brackets.
HD 4K 101 Plus • Introduction 2
Panel Features
This section describes:
• HD 4K 101 Plus Front Panel
• HD 4K 101 Plus Rear Panel
HD 4K 101 Plus Front Panel
HD 4K 101 Plus
HDMI IN
A
B
Figure 2. HD 4K 101 Plus Front Panel
A
Status LED — lights amber when the product is receiving power from either the
12 VDC connector or via Pin 18 of the HDMI input from a source device. The LED
lights green when an HDMI signal is present, which is detected from TMDS Clock.
B
HDMI Input — a single female HDMI Type A connector. The input equalizes the input
cable signal at the highest support rate of 600 MHz (see the Input Cable Lengths
table below).
The input can also receive power from the video source, via pin 18 (+5 VDC) of the HDMI
connector. If the source does not supply adequate power, the status LED will not light
amber, and an external power supply must be used (see Attention on page 6). The
Extron PS Series Desktop Power Supply is sold separately at www.extron.com.
Input Cable Lengths
Resolution Refresh Rate (Hz) Maximum distance
720p 24/30 175 feet (53.3 meters)
720p 60 150 feet (45.7 meters)
1080i 30/60 150 feet (45.7 meters)
1080p 24/30 150 feet (45.7 meters)
1080p (8 bit or deep color) 60 125 feet (38.1 meters)
3840x2160 (UHD) 24/30 75 feet (22.9 meters)
4096x2160 (4K) 24/30 75 feet (22.9 meters)
3840x2160 (UHD) 60 50 feet (15.2 meters)
4096x2160 (4K) 60 35 feet (10.7 meters)
HD 4K 101 Plus • Panel Features 3
Resolution Refresh Rate (Hz) Maximum distance
PC Rates
1024x768 60 150 feet (45.7 meters)
1280x1024 60 150 feet (45.7 meters)
1600x1200 60 125 feet (38.1 meters)
1920x1080 24/30 150 feet (45.7 meters)
1920x1080 60 125 feet (38.1 meters)
1920x1200 60 125 feet (38.1 meters)
2560x1600 30 75 feet (22.9 meters)
2560x1600 60 50 feet (15.2 meters)
3840x2160 24/30 75 feet (22.9 meters)
4096x2160 24/30 75 feet (22.9 meters)
3840x2160 60 50 feet (15.2 meters)
4096x2160 60 35 feet (10.7 meters)
NOTE: To send signals the distances shown in the Input Cable Lengths
table above, Extron recommends the use of HDMI Pro cables (see
www.extron.com).
Securing the HDMI Connector
Use a HDMI cable to connect the input source to
the female HDMI socket on the front panel of the
HD 4K 101 Plus (figure 2,
B
, on page 3).
Use the provided LockIt HDMI Cable Lacing Bracket
to secure the HDMI connector:
1. Plug the HDMI cable into the panel connection.
2. Loosen the HDMI connection mounting screw
from the panel enough to allow the LockIt lacing
bracket to be placed over it. The screw does
not have to be removed.
3. Place the LockIt lacing bracket on the screw
and against the HDMI connector, then tighten
the screw to secure the bracket.
ATTENTION:
• Do not overtighten the HDMI
connection mounting screw. The
shield it fastens to is very thin and can
easily be stripped.
• Ne serrez pas trop la vis de montage
du connecteur HDMI. Le blindage
auquel elle est attachée est très fin et
peut facilement être dénudé.
4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing
bracket as shown.
5. While holding the connector securely against the lacing bracket, tighten the tie wrap,
and then remove any excess length.
3
11
22
3
3
4
4
5
5
HD 4K 101 Plus • Panel Features 4
HD 4K 101 Plus Rear Panel
POWER
12V
0.2A MAX
HDMI OUT
A
B
Figure 3. HD 4K 101 Plus Rear Panel
A
Power Input — connect the (optional) 12 VDC, 1.0 A
power supply to this single female, two-pole, 3.5 mm,
captive screw connector.
WARNING: The two power cord wires must be
kept separate while the power supply is plugged in.
Remove power before wiring.
AVERTISSEMENT: Les deux cordons d’alimentation
doivent être tenus à l’écart l’un de l’autre quand
l’alimentation est branchée. Couper l’alimentation
avant de faire l’installation électrique.
ATTENTION:
• Do not connect any external power supplies until
you have read the Attention notifications on
page 6.
• Ne branchez pas de sources d’alimentation
externes avant d’avoir lu les mises en garde sur la
page 6.
1. Cut the DC output cord to the length needed.
2. Strip the jacket to expose 3/16 inch (5 mm) of the conductor wire.
ATTENTION:
• The length of the exposed wires in the stripping process is critical. The
ideal length is 3/16 inches (5 mm). Any longer and the exposed wires
may touch, causing a short circuit between them. Any shorter and the
wires can be easily pulled out even if tightly fastened by the captive
screws.
• La longueur des câbles exposés est primordiale lorsque l’on entreprend
de les dénuder. La longueur idéale est de 5mm (3/16inches). S’ils
sont un peu plus longs, les câbles exposés pourraient se toucher et
provoquer un court circuit. S’ils sont un peu plus courts, ils pourraient
sortir, même s’ils sont attachés par les vis captives.
3. Ensure the connections have the correct polarity as shown in the figure above.
4. Slide the exposed ends of the wire into the captive screw connector and secure
by tightening the screws.
5. Use the supplied tie wrap to strap the power cord to the extended tail of the
connector.
A
Power Input
B
HDMI Output
SECTION A–A
Ridges
Smooth
AA
3/16"
(5 mm) Max.
POWER
12V
0.2A MAX
HD 4K 101 Plus • Panel Features 5
ATTENTION:
• Always use a power supply provided by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product.
• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit
final.
• These products are intended for use with a UL Listed power source marked
“Class 2” or “LPS” and rated 12VDC, minimum 1.0 A.
• Ces produits sont destiné à une utilisation avec une source d’alimentation
listéeUL avec l’appellation «Classe2» ou «LPS» et normée 12Vcc, 1,0A
minimum.
• Extron power supplies are certified to UL/CSA 60950-1 and are classified as LPS
(Limited Power Source). Use of a non-LPS or unlisted power supply will void all
regulatory compliance certification.
• Les sources d’alimentation Extron sont qualifiées UL/CSA60950-1 et sont
classéesLPS(LimitedPowerSource). L’utilisation d’une source d’alimentation
non-listée ou non-listéeLPS annulera toute certification de conformité
réglementaire.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air
handling spaces or in wall cavities. The power supply is to be located within the
same vicinity as the Extron AV processing equipment in an ordinary location,
Pollution Degree 2, secured to the equipment rack within the dedicated closet,
podium, or desk.
• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour
une utilisation dans les espaces d’aération ou dans les cavités murales. La
source d’alimentation doit être située à proximité de l’équipement de traitement
audiovisuel dans un endroit ordinaire, avec un degré2 de pollution, fixé à un
équipement de rack à l’intérieur d’un placard, d’une estrade, ou d’un bureau.
• The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16.
• Cette installation doit toujours être en accord avec les mesures qui s’applique
au National Electrical Code ANSI/NFPA70, article725, et au Canadian Electrical
Code, partie1, section16.
• The power supply shall not be permanently fixed to building structure or similar
structure.
• La source d’alimentation ne devra pas être fixée de façon permanente à une
structure de bâtiment ou à une structure similaire.
• Do not tin the wire leads before installing into the connector. Tinned wires are not
as secure in the connector and could be pulled out. They may also break after
being bent several times.
• Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les
câbles étamés ne sont pas aussi bien fixés dans le connecteur et pourraient être
retirés. Ils peuvent aussi se casser après avoir été pliés plusieurs fois.
HD 4K 101 Plus • Panel Features 6
B
HDMI Output (see figure 3 on page 5)— One female HDMI Type A connector used
for HDMI output. The output supports a pixel clock up to 600 MHz. The cable length
connecting to the display device must be a maximum of 12 feet (3.6 m).
Use the provided LockIt HDMI lacing bracket to secure the HDMI connector (see
Securing the HDMI Connector on page 4).
Powering Via the Input Source
The HD 4K 101 Plus can receive power from the input device via the 5VDC signal on
pin 18 of the HDMI cable. This eliminates the external power supply. If an external power
supply is needed, connect the optional Extron 12V/1A power supply.
NOTES:
• If the source does not adequately supply the +5 VDC power, an external
power supply must be used.
• To verify if the source is providing power, connect a short HDMI cable from
the input device to the input of the cable equalizer. If the HD 4K 101 Plus
front panel LED lights amber, the source is supplying power.
Internal Settings
Under most conditions, the HD 4K 101 Plus works without adjustments. However, the
quality of the image displayed may be affected by a combination of the source, display,
and cable length. If so, the HD 4K 101 Plus has two sets of jumper switches that are used
to adjust Equalization (EQ), and Pre-emphasis (see figure 4 and table 1 on the following
page).
Follow these instructions to get access to these jumper switches:
ATTENTION:
• Electrostatic discharge (ESD) can damage IC chips even though you cannot
feel, see, or hear it. Use electrostatic discharge (ESD) precautions (be electrically
grounded) when making connections.
• Les décharges électrostatiques peuvent endommager les puces de circuit même
si vous ne pouvez pas les sentir, les voir ou les entendre. Prenez des précautions
contre les décharges électrostatiques (soyez électriquement relié à la terre)
lorsque vous effectuez des connexions.
1. Remove the screws holding the cover to the base, one screw on the front panel and
two screws on each side. Set aside the cover and retain the screws.
NOTE: Do not remove the screw from the back panel. This secures the internal
circuit board and does not attach the base to the cover.
2. Locate the four sets of jumper switches on the side of the circuit board
(see figure 4 on the next page).
HD 4K 101 Plus • Panel Features 7
Rear Panel
(top removed)
Set Jumper Switches
1
3
1
3
1
3
J4
EQ
Pre-emphasis
J6
3
3
1
1
Jumper Switches
(2 sets)
Figure 4. Locating the Jumper Switches
3. Set the jumper switches as required (see table 1 below).
4. Replace the cover, using the screws that were removed and saved in step 1.
Internal Jumper Settings
Jumper Function Jumper
Pins 2 and 3
Jumper
Pins 1 and 2
No Jumper
J4 (EQ) Adjusting this jumper can improve the image for
some applications with longer cable runs, image
artifacts, or both.
Setting for J4 (EQ), based on resolutions and the
input HDMI cable lengths used:
•
High:
1080p @ 60 Hz with input cables 100-125 feet.
4k/30 with input cables 50-75 feet.
4k/60 with input cables 25-35 feet.
•
Mid:
1080p @ 60 Hz with input cables 50-100 feet.
4k/30 with input cables 25-50 feet.
4k/60 with input cables 15-25 feet.
•
Low:
1080p @ 60 Hz with input cables 15-50 feet.
4k/30 with input cables 15-25 feet.
4k/60 with input cables less than 15 feet.
Low
1
3
Mid
1
3
High
Default
1
3
J6 (Pre-emphasis) Adjusting this jumper can compensate for
signal degradation in applications with higher
data rate, higher resolution, or both. This
adjustment is recommended for resolutions of
2560x1600@60Hz or higher.
On
1
3
Off
Default
1
3
Not used
1
3
HD 4K 101 Plus • Panel Features 8
Connecting for Long Cable Runs
To use the HD 4K 101 Plus effectively, follow the recommendations in figure 5 for cable
lengths between the source device and HD 4K 101 Plus and between the HD 4K 101
Plus and the display device. Position the HD 4K 101 Plus at the end of the cable closest
to the display.
Source
Long Cable
from Source
( up to 175 feet (53.3m))
Short Cable
to Display
( less than
15 feet (4.5m))
Display
HD 4K 101 Plus
Figure 5. Optimum Cable Lengths between the Source, HD 4K 101 Plus, and
Display
HD 4K 101 Plus • Panel Features 9
Mounting
This section outlines the HD 4K 101 Plus mounting options:
• Tabletop Mounting
• Rack Mounting
• Under Desk Mounting
• Through Desk Mounting
Tabletop Mounting
Attach the four provided rubber feet to the bottom of the HD 4K 101 Plus and place the
unit in any convenient location.
Rack Mounting
Underwriters Laboratories Guidelines for Rack Mounting
The following Underwriters Laboratories (UL) guidelines are relevant to the safe installation
of these products in a rack:
1. Elevated operating ambient temperature — If the unit is installed in a closed or
multi-unit rack assembly, the operating ambient temperature of the rack environment
may be greater than room ambient temperature. Therefore, install the equipment in an
environment compatible with the maximum ambient temperature (Tma: +122 °F,
+50 °C) specified by Extron.
2. Reduced air flow — Install the equipment in the rack so that the equipment gets
adequate air flow for safe operation.
3. Mechanical loading — Mount the equipment in the rack so that uneven mechanical
loading does not create a hazardous condition.
4. Circuit overloading — Connect the equipment to the supply circuit and consider the
effect that circuit overloading might have on overcurrent protection and supply wiring.
Give appropriate consideration to the equipment nameplate ratings when addressing
this concern.
5. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted
equipment. Pay particular attention to supply connections other than direct
connections to the branch circuit (such as the use of power strips).
Rack Mounting the HD 4K 101 Plus
See the Extron website for a list of optional rack mounting kits that are suitable for the
HD 4K 101 Plus. Follow the instructions provided with the kit.
Under Desk Mounting
See the Extron website to find the optional under desk mounting kit that is suitable for the
HD 4K 101 Plus. Follow the instructions provided with the kit.
Through Desk Mounting
See the Extron website to find the optional through desk mounting kit that is suitable for
the HD 4K 101 Plus. Follow the instructions provided with the kit.
HD 4K 101 Plus • Mounting 10
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of three years
from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty
workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is
returned within the warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1230 South Lewis Street
Anaheim, CA 92805
U.S.A.
Japan:
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe and Africa:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Extron Asia Pte Ltd
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Middle East:
Extron Middle East
Dubai Airport Free Zone
F13, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical
or mechanical abuse, abnormal operating conditions, or if modifications were made to the product that were not
authorized by Extron.
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return
Authorization) number. This will begin the repair process.
USA: 714.491.1500 or 800.633.9876 Europe: 31.33.453.4040
Asia: 65.6383.4400 Japan: 81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage
during shipment. Returned units must include the serial number and a description of the problem, as well as the
name of the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality,
performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct,
indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this warranty may
not apply to you.
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8351.2188
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. www.extron.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Extron HD 4K 101 Plus Manuel utilisateur
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Extron HD 4K 101 Plus User manual
Documents connexes
-
Extron HD 4K 101 Plus Manuel utilisateur
-
-
-
Extron UHD4K 101 Manuel utilisateur
-
Extron DVI 101 Manuel utilisateur
-
-
Extron HD 4K 110 Series Manuel utilisateur
-
Extron XTP SFR HD 4K Manuel utilisateur
-
-