Control4 C4-TV120277-BL Guide d'installation

Marque: Control4

Modèle: C4-TV120277-BL

Taper: Guide d'installation

™

Warnings and considerations

WARNING! Turn OFF electrical power before installing or servicing this

product. Improper use or installation can cause SERIOUS INJURY, DEATH

or LOSS/DAMAGE OF PROPERTY.

ATTENTION! ATTENTION! Coupez l’alimentation électrique avant

d’installer ou de réparer ce produit. Une mauvaise installation ou utilisation

peut entraîner des blessures graves, décès ou perte / dommages à la

propriété.

WARNING! This device must be protected by a circuit breaker (20A max).

ATTENTION! Cet appareil doit être protégé par un disjoncteur (20A max.)

WARNING! Ground this device in accordance with the National Electric

Code (NEC) requirements. DO NOT rely solely upon the yoke plate’s

contact with a metal wallbox for adequate grounding. Use the device’s

ground wire to make a secure connection to the safety ground of the

electrical system.

ATTENTION! Cet appareil doit être en conformité avec le Code national

de l’électricité (NEC). Ne comptez pas uniquement au contact de la

plaque avant avec un boîtier mural métallique pour la mise à la terre

adéquate. Utilisez cet appareil à la terre de l’appareil pour établir une

connexion sécurisée au système électrique.

IMPORTANT! This device must be installed by a licensed electrician in

accordance with all national and local electrical codes.

IMPORTANT! If you are unsure about any part of these instructions,

consult a qualiﬁed electrician.

IMPORTANT! Use this device only with copper or copper-clad wire. Do

not use aluminum wiring. This product has not been approved for use with

aluminum wiring.

IMPORTANT! To reduce the risk of overheating and possible damage

to other equipment, do not install to control a receptacle or a motor-

operated appliance.

IMPORTANT! Using this product in a manner other than outlined in this

document voids your warranty. Further, Control4 is NOT liable for any

damage incurred with the misuse of this product. See “Troubleshooting.”

IMPORTANT! Do NOT use a power screwdriver to install this device. If you

do, you may overtighten the screws and strip them. Also, overtightening

the screws may interfere with proper button operation.

IMPORTANT! This is an electronic device with intricate components.

Handle and install with care!

IMPORTANT! When used in conjunction with an Auxiliary Keypad

(C4-KA-xx), the wire connecting the Auxiliary Keypad to the dimmer must

not exceed 150 feet (45 m) at 120VAC, and 100 feet (30 m) at 277VAC.

Installation instructions

1 Ensure that the location and intended use meet the following criteria:

• Do not exceed the load capacity requirements of the dimmer. Refer to the

load ratings in the speciﬁcations above for details.

• Install in accordance with all applicable national and local electrical codes.

• The range and performance of the wireless control system is highly

dependent on the following: (1) distance between devices; (2) layout

of the home; (3) walls separating devices; and (4) electrical equipment

located near devices.

2 Turn o the local electrical power by either switching o the circuit breaker or

removing the fuse from the fuse box. To ensure the wires do NOT have power

running to them, use an inductive voltage detector.

Supported Model

• C4-TV120277 0-10V Dimmer

Introduction

The Control4® 0-10V Dimmer operates independently or as part of a Control4

home automation system. It installs in a standard back box using typical wiring

standards and communicates to the Control4 system using a wireless connection.

Box contents

• 0-10V Dimmer

• Wire nuts

• Warranty card

• 0-10V Dimmer Installation Guide (this document)

Speciﬁcations and supported load types

The speciﬁcations are described below.

Model number C4-TV120277-xx

Power requirements 120-277VAC +/-10%, 50/60Hz

This device requires a neutral AC connection.

See “Sample Wiring Conﬁgurations” later in this

guide.

Power consumption 120V: 485 mW

277V: 1.18 W

Load types and ratings

Supported load types Four-wire 0-10V and 1-10V dimmable

ﬂuorescent ballasts and LEDs, sink or source.

Maximum load (switched hot) 120V: 15A

277V: 8A

Maximum load (0-10V

Control)

100mA sink or source

Environmental

Operational temperature 32˚ F - 104˚ F (0˚ C - 40˚ C)

All load ratings are based on an ambient

temperature of 25˚ C

Humidity 5% to 95% non-condensing

Storage -4˚F ~ 158˚F (-20˚C ~ 70˚C)

Miscellaneous

Control communications ZigBee, IEEE 802.15.4, 2.4 GHz, 15-channel

spread spectrum radio

Wallbox volume 5.75 cubic inches

Weight 0.12 lb. (0.05 kg)

Shipping weight 0.18 lb. (0.08 kg)

0-10V Dimmer

Installation Guide

NOTE: The back box wiring shown in this document is an example. Your

wire colors and functions may dier. If you are not sure which wires are

the Line In/Hot, Neutral, Load, and Earth Ground wires, have a trained

electrician perform the installation.

3 Prepare each wire. Wire insulation should be stripped back 5/8 of an inch

from the wire end (see Figure 1).

Figure 1. Strip wire insulation

4 Identify your wiring application, and then see the appropriate wiring diagram

in the “Sample Wiring Conﬁgurations” section below.

IMPORTANT! Not grounding this product as described in the section,

“Warnings and Considerations,” may result in an installation less immune

to damage caused by electrical disturbances, such as ESD or lightning,

and may void the warranty.

5 Identify and connect the dimmer wires to the back box wires using the wire

nuts.

IMPORTANT! The yellow wire is not a traditional traveler. It cannot directly

power a lighting load. It must be used only to connect to a Control4

Auxiliary Keypad. See “Sample Wiring Conﬁgurations.”

TIP: If you are using a Control4 push-on (screwless) faceplate in a multi-

gang installation, attach the black faceplate sub-plate to all of the devices

that will be installed into the wallbox prior to attaching the devices to the

wallbox. This will help ensure that all the devices are properly aligned and

on the same plane after installation.

6 Fit the wires back into the back box. Bend the wires in a zigzag pattern so

that they easily fold into the back box (Figure 2).

Figure 2. Bend the wires

7 Align the dimmer to the back box (the load rating label should be at the

bottom) and fasten it with screws. Tighten the screws until the back side of

the yoke plate is even with the wall surface, but no further. Overtightening can

warp the dimmer and cause mechanical malfunction.

8 Install the Control4 Faceplate following the instructions in the Faceplate

Installation Guide or attach a standard Decora-style faceplate.

9 Turn ON power at the circuit breaker or replace the fuse

from the fuse box.

NOTE: If the light ﬂickers, adjust the dimmer’s max/min settings in

Composer (e.g. min 15%, max 85%). See ctrl4.co/dimmersettings.

Operation and conﬁguration

On initial power up, all status LEDs on the dimmer will illuminate green indicating

that the device has power. To set up this dimmer for use with a Control4 system,

refer to the Composer Pro User Guide.

To operate this dimmer as a stand-alone device:

• Click the top button to turn the light on.

• Click the bottom button to turn the light o.

• Press and hold the top button to ramp the light up. Release the button at the

desired light level.

• Press and hold the bottom button to fade the light down. Release the button

at the desired light level.

Button tap sequences

The button tap sequences are deﬁned in the table below. Button tap sequences

that require a single (1) button should use the top button.

Function Button sequence

Identify 4

ZigBee channel 7

Reboot 15

Factory reset 9-4-9

Leave mesh and reset 13-4-13

Troubleshooting

If the light does not turn on:

• Ensure at least one LED on the face of the dimmer is lit.

• Ensure the light bulb is not burned out and is screwed in tightly.

• Ensure that the circuit breaker is not turned OFF or tripped.

• Check for proper wiring (see “Sample Wiring Conﬁgurations”).

• For help on the installation or operation of this product, email or call the

Control4 Technical Support Center. Please provide your exact model number.

Contact support@control4.com or see the web site www.control4.com.

Care and cleaning

• Do NOT paint the dimmer or its wall plate.

• Do NOT use any chemical cleaners to clean the dimmer.

• Clean surface of the dimmer with a soft damp cloth as needed.

Regulatory/Safety information

To review Regulatory information for your particular Control4 products, see

the information located on the Control4 website at: http://www.control4.com/

regulatory/.

Patent information

Applicable patents are available at http://www.control4.com/legal/patents.

Warranty

For complete warranty information, including details on consumer legal rights as

well as warranty exclusions, review the Warranty card or visit www.control4.com/

warranty.

™

Sample wiring conﬁgurations

Figure 3. Single device location, with neutral connection

Figure 4. Multiple device location using Auxiliary Keypad, with neutral connection

IMPORTANT! When used in conjunction with an Auxiliary Keypad (C4-KA-xx), the wire connecting the Auxiliary Keypad to the dimmer must not exceed 150 feet

(45 m) at 120VAC, and 100 feet (30 m) at 277VAC.

Auxiliary

Line in/Hot

Black

White

Red

Purple

Neutral in

Yellow

Blue/White

Auxiliary Keypad

Figure 5. Multiple device location using Conﬁgurable Keypad, neutral required

Line in/Hot

Black

White

Neutral in

Green/

Yellow

Earth ground

Conﬁgurable Keypad

the United States and/or other countries. All other names and brands may be claimed as the property of their respective owners Pricing and speciﬁcations are subject to change without notice

200-00312-C 10162019 LW