Delta EIDWU25TSUB02 Manuel utilisateur

DC Wallbox 25kW

Installation and Operation Manual

Version: 1

Issue date: 2023/03

Installation and Operation Manual

i

TABLE OF CONTENTS

Introduction ............................................................................................ 1

Features ...................................................................................... 1

Applications ................................................................................. 2

Important Safety and Wiring Instructions ................................................ 3

Installation Site Selection ............................................................ 3

Safety and Compliance ............................................................... 3

Service Wiring ............................................................................. 4

Before Installation .................................................................................. 7

Safety Requirements ................................................................... 7

Accessory Kit ............................................................................... 8

Recommended Tools .................................................................. 9

Installing the DC Wallbox Charger........................................................ 10

Making the Connection ......................................................................... 13

Operation ............................................................................................. 21

System Configuration ........................................................................... 23

Cellular Configuration ................................................................ 24

Firmware Update ....................................................................... 24

Maintenance ........................................................................................ 25

System Code ....................................................................................... 26

Specifications ....................................................................................... 28

Conventions

Installation and Operation Manual

ii

General Conventions

The following conventions are used in this manual:

Note:

Indicates additional information that is relevant to the current process or procedure.

WARNING!

Warning information appears before the text it references to emphasize that the content may

prevent damage to the device or equipment.

CAUTION!

CAUTIONS APPEAR BEFORE THE TEXT IT REFERENCES. CAUTIONS APPEAR IN CAPITAL LETTERS TO

EMPHASIZE THAT THE MESSAGE CONTAINS VITAL HEALTH AND SAFETY INFORMATION.

Typographical Conventions

The following typographical conventions are used in this document:

Italics

Indicates book titles, directory names, file names, path names, and program/process names.

Constant width

Indicates computer output shown on a computer screen, including menus, prompts, responses to

input, and error messages.

Constant width bold

Indicates commands or information literally entered by a user on the computer. Variables contained

within user input are shown in angle brackets (< >).

Bold italics.

Indicates keyboard keys that are pressed by the user.

!

Copyright

Installation and Operation Manual

iii

The ownership and all intellectual property rights of this Installation and Operation Manual (this “Man-

ual”), including but not limited to the content, data and figures contained herein are vested by Delta

Electronics, Inc. (“Delta”). The Manual can only be applied to operation or use of the product. Any dis-

position, duplication, dissemination, reproduction, modification, translation, extraction or any other

usage to the Manual is prohibited without obtaining Delta’s prior written permission. As the product will

be developed and improved continuously, Delta may modify or update the Manual from time to time

without any notice. Delta will do its best efforts to keep the Manual updated and maintain the accuracy

of the Manual. Delta disclaims any kinds or forms of warranty, guarantee or undertaking, either

expressly or implicitly, including but not limited to the completeness, accuracy, non-infringement, mer-

chantability or fitness for particular purpose or usage.

Introduction

Installation and Operation Manual

1

Introduction

The DC Wallbox charger is the top choice for powering battery electric vehicles (BEV and plug-in elec-

tric vehicles (PHEV) today. It is designed for quick charging in both public and private locations, such as

retail and commercial parking spaces, fleet charging stations, highway rest areas, workplaces, resi-

dences, etc.

The DC Wallbox charger has the advantage of easy installation. The wall-mounting design and plugga-

ble power modules allow for flexible and cost-effective installation at various types of locations. The DC

Wallbox charger also features network communication capability; it is able to connect with remote net-

work systems and provide drivers of electric cars real-time information, such as the locations of

charging stations, charging progress information and billing information. The DC Wallbox charger has a

clear user interface with function buttons, a power supply safety system and excellent waterproof and

dust-proof technology to provide the best choice for outdoor environments. It can also integrate with

renewable energy systems, such as solar power and wind power technology, to provide the most

energy saving infrastructure for EV system development.

Features

 Wall-mount design and pluggable power modules make installation easy and flexible.

 Offers customers the convenience of full start and stop charging control from an authorized

RFID smart card.

 Built according to latest industry standards for DC charging.

 Carries an outdoor rating capable of withstanding solid and liquid intrusions in outdoor settings,

making the unit more stable and highly reliable.

 Provides a high-contrast, OLED screen interface with multi-function buttons.

Introduction

Installation and Operation Manual

2

Applications

 Public and private parking areas

 Community parking areas

 Parking areas of hotels, supermarkets and shopping malls

 Workplace parking areas

 Charging stations

 Highway rest areas

CCS1

Charging plug

and cable

Key switch

Antenna

Emergency

button

2.7” OLED display

Push buttons

RFID card reader

Important Safety and Wiring Instructions

Installation and Operation Manual

3

Important Safety and Wiring Instructions

Installation Site Selection

DC Wallbox can be installed in both indoor and outdoor environments. It is necessary to consider the

installation conditions and protection at the site:

 Follow local electrical regulation and installation standards

 Consider the emergency routes at the installation site

 Do not install the device at potentially explosive atmosphere areas (Ex areas).

Safety and Compliance

 Read the manual before installation or usage of device.

 Do not put tools, material or body parts into the electric vehicle connector.

 Do not use the DC Wallbox charger if the cabinet, power cord or charging cable are frayed, have

broken insulation or show any other signs of damage.

 Do not install or use the DC Wallbox charger if the enclosure is broken, cracked, open or shows

any other indications of damage.

 The DC Wallbox charger should be installed only by a qualified technician.

 Make sure that the materials used and the installation procedures follow local building codes

and safety standards.

 The information provided in this manual in no way exempts the user of responsibility to follow all

applicable codes or safety standards.

 The manufacturer is not responsible for physical injury, damage to property or damage to equip-

ment caused by the installation of this device.

 This document provides instructions for the DC Wallbox charger and should not be used for any

other product. Before installation or use of this product, you should review this manual carefully

and consult with a licensed contractor, licensed electrician or trained installation expert to make

sure of compliance with local building codes and safety standards.

Important Safety and Wiring Instructions

Installation and Operation Manual

4

Service Wiring

Ground Connection

Always connect the Neutral at the service to Earth Ground. If ground is not provided by the electrical

service, a grounding stake must be installed nearby. The grounding stake must be connected to the

ground bar in the main breaker panel, and the Neutral must be connected to Ground at that point.

240V Single-Phase

WARNING!

If the DC Wallbox is a single-phase device, do not connect to a three-phase feed.

WARNING!

The following diagram illustrates the DC Wallbox connection to L1 and L2 in a single-phase

power grid feed. The earth ground must be connected to neutral at a single point, typically at

the breaker panel.

WARNING!

An earth connection is essential before connecting supply.

!

Important Safety and Wiring Instructions

Installation and Operation Manual

5

277V Single-Phase

WARNING!

If the DC Wallbox is a single-phase device, do not connect to a three-phase feed.

WARNING!

The following diagram illustrates the DC Wallbox connection to L1 and N in a single-phase

power grid feed. The earth ground must be connected to neutral at a single point, typically at

the breaker panel.

WARNING!

An earth connection is essential before connecting supply.

480V Three-Phase

WARNING!

The following diagram illustrates the DC Wallbox connection to L1, L2, L3, and neutral in a

y-connection power grid feed. The earth ground must be connected to neutral at a single

point, typically at the breaker panel.

WARNING!

An earth connection is essential before connecting supply.

277V

480V 480V

277V

!

Important Safety and Wiring Instructions

Installation and Operation Manual

6

208V Three-Phase

WARNING!

The following diagrams illustrates the DC Wallbox connection to L1, L2, and L3. Neutral

connection is not required.

WARNING!

An earth connection is essential before connecting supply.

208V

!

Before Installation

Installation and Operation Manual

7

Before Installation

Safety Requirements

 Be sure to preview the standard operating procedures (SOP) and ensure local building and elec-

trical codes are reviewed before installing the DC Wallbox charger.

 The DC Wallbox charger should be installed by a qualified technician according to the instruction

manual and local safety regulations.

 Use appropriate protection when connecting to the main power distribution cable.

 Disconnect switch for each ungrounded conductor of ac input shall be provided by others in

accordance with the National Electric Code, ANSI/NFPA 70.

CAUTION!

TO REDUCE RISK OF FIRE FOR 1 PHASE 200VAC-277VAC INPUT, IN ACCORDANCE WITH THE

NATIONAL ELECTRIC CODE, ANSI/NFPA 70, THE UPSTREAM CIRCUIT BREAKER SHOULD BE

INSTALLED WITH A RATED CURRENT OF 175A.

CAUTION!

TO REDUCE RISK OF FIRE FOR 3 PHASE 480VAC INPUT, IN ACCORDANCE WITH THE NATIONAL

ELECTRIC CODE, ANSI/NFPA 70, THE UPSTREAM CIRCUIT BREAKER SHOULD BE INSTALLED WITH

A RATED CURRENT OF 50A.

CAUTION!

TO REDUCE RISK OF FIRE FOR 3 PHASE 208VAC INPUT, IN ACCORDANCE WITH THE NATIONAL

ELECTRIC CODE, ANSI/NFPA 70, THE UPSTREAM CIRCUIT BREAKER SHOULD BE INSTALLED WITH

A RATED CURRENT OF 125A.

Note:

Depends on local regulations requirements.

Note:

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. The equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Note:

To implement cyber security, please follow instruction below:

 EVSE shall connect to the backend system with secure web socket protocol (wss).

 Network with cellular (2G/3G/4G) connection shall utilize VPN

 Network with WLAN or Ethernet connection shall utilize a router with VPN function

 If EVSE support WLAN AP mode for maintenance purpose, please turn off the

function after finishing the installation.

Before Installation

Installation and Operation Manual

8

CAUTION!

ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE GRANTEE OF THIS DEVICE

COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUPMENT.

RF Exposure warning:

This equipment must be installed and operated in accordance with provided instructions

and the antenna(s) used for this transmitter must be installed to provide a separation

distance of at least 20 cm from all persons and must not be co-located or operating in

conjunction with any other antenna or transmitter. End-users and installers must be

provide with antenna installation instructions and transmitter operating conditions for

satisfying RF exposure compliance.

Canada, Industry Canada (IC) Notices

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,

Science and Economic Development Canada’s licence-exempt RSS(s). Operation is

subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause

undesired operation of the device.

Canada, avis d'Industry Canada (IC)

Cet appareil contient un ou des émetteurs/récepteurs exempts de licence conformes aux

RSS exempts de licence d'Innovation, Sciences et Développement économique Canada.

Le fonctionnement est soumis aux deux conditions suivantes:

Cet appareil ne doit pas causer d'interférences.

Cet appareil doit accepter toutes les interférences, y compris les interférences pouvant

entraîner un fonctionnement indésirable de l'appareil.

Radio Frequency (RF) Exposure Information

The radiated output power of the Wireless Device is below the Innovation, Science and

Economic Development Canada (ISED) radio frequency exposure limits. The Wireless

Device should be used in such a manner such that the potential for human contact during

normal operation is minimized.

This device has also been evaluated and shown compliant with the IC RF Exposure limits

under mobile exposure conditions. (Antennas are greater than 20cm from a person's

body).

Informations concernant l'exposition aux fréquences radio (RF)

La puissance de sortie rayonnée de l'appareil sans fil est inférieure aux limites d'exposition

aux radiofréquences d'Innovation, Sciences et Développement économique Canada

(ISDE). L'Appareil sans fil doit être utilisé de telle manière que le potentiel de contact

humain pendant le fonctionnement normal soit minimisé.

Cet appareil a également été évalué et démontré conforme aux limites d'exposition RF IC

dans des conditions d'exposition mobile. (Les antennes sont à plus de 20 cm du corps

d'une personne).

Contains FCC ID:QIPPLS8-X

Contains IC:7830A-PLS8X

Before Installation

Installation and Operation Manual

9

Accessory Kit

Mounting bracket x 1 Mounting template x 1 RFID cards x 2 Switch Keys x 2,

Latch Keys x 2

User manual x 1 CCS1 plug holder x 1

Bag of bracket screws

x 2

(SCREW M M6*1*8

PAN TORX SUS NL)

Bag of grounding

screw x 1

(SCREW M M6*1*12

HEXH C S+P S20C ZN-NI)

Bag of expansion bolts x 6

(+2 for dual output model)

(ANCHOR SUS

16*50.8 PICKLING)

RFID card

Before Installation

Installation and Operation Manual

1

0

Recommended Tools

The following tools are recommended for the DC Wallbox charger installation:

 (1x) Voltmeter or digital multi-meter

 (1x) Water level

 (1x) Hammer

 (1x) Concrete drilling machine

 (1x) Wire cutters / strippers

 (1x) Torx®

Tamper-Resistant T15 & T25 screwdriver

 (1x) No.8 Flathead screwdriver and socket wrench

 (1x) No.6 Flathead screwdriver

 (1x) No.2 Philips screw driver

 (1x) M50 conduit hub, conduit and wrench for main power wires

 (1x) M25 conduit hub, conduit and wrench for Ethernet

 (2x) Ring terminal RNB70-10 for L/N wire (#2/0 AWG, 90°C copper wire) in models with 240V

and 277V single-phase input

 (3x) Ring terminal RNB38-6 for L1/L2/L3 wire (#2 AWG, 90°C copper wire) in models with 208V

three-phase input

 (4x) Ring terminal RNB14-6 for L1/L2/L3/N wire (#6 AWG, 90°C copper wire) in models with

480V three-phase input

 (1x) Ring terminal RNB14-6 for PE/ground wire (#6 AWG, 90°C copper wire)

WARNING!

Danger of electrical shock or injury. Turn off power at the panel board or load center before

working inside the equipment or removing any component. Do not remove circuit protective

devices or any other component until the power is turned off.

CAUTION!

TO AVOID DAMAGE TO THE CHARGER OR PERSONAL INJURY, MAKE SURE THE INSTALLATION

LOCATION IS ABLE TO SUPPORT THE WEIGHT OF THE DC WALLBOX CHARGER.

Important Safety Instructions.

Save these Instructions.

 The DC Wallbox charger should be installed only by a licensed contractor, and/or a licensed

electrician in accordance with all applicable state, local and national electrical codes and stan-

dards.

 Before installing the DC Wallbox charger, review this manual carefully and consult with a

licensed contractor, licensed electrician and trained installation expert to ensure compliance

with local building practices, climate conditions, safety standards and state and local codes.

!

Installing the DC Wallbox Charger

Installation and Operation Manual

10

Installing the DC Wallbox Charger

Preparation

1. Release the screws on the crate (two sides) with a No. 8 socket wrench.

2. OOpen top lid of plywood crate.

3. Take out mounting template and cut off the cable ties to move the charging plug.

Installing the DC Wallbox Charger

Installation and Operation Manual

11

4. Remove top foam, open plastic bag and take out the unit.

Note:

Carefully place the unit and the charging plug on the ground or a flat surface at this stage.

Wall Mounting

1. Use template and leveler tool to mark out the mounting position.

2. Mount bracket onto the wall.

Note:



The unit must be mounted on a solid wall (concrete or metal preferred).

 Use the expansion bolts in the accessory kit or choose proper mounting screws for

different types of wall. A drilling machine might be needed for certain conditions.

 Follow applicable accessibility requirements for the mounting position. The unit must be

mounted at a sufficient height from grade such that the height of the storage is located

between 60 cm (24 inches) and 120 cm (4 feet) from grade per NEC Article 625.

 Leave a minimum of 650 mm on both sides of the charger for service maintenance.

Installing the DC Wallbox Charger

Installation and Operation Manual

12

WARNING!

To ensure adequate ventilation and maintenance space, leave a minimum of 45 cm (18

inches) on both sides of the charger.

3. Place unit onto bracket. Align the back chassis of unit with the corresponding slot on the bracket.

Slowly slide down the unit until it sits firmly on the bracket. Fasten two screws from the bottom.

Note:

The bottom fixing screws are in the accessory kit.

!

Making the Connection

Installation and Operation Manual

13

Making the Connection

WARNING!

Only use a Torx® Tamper-Resistant T15 screwdriver to secure or remove the screws. Use of

any other tool may damage screws and panel.

Power Wiring

1. Open front cover for wiring.

a. Release two screws on top.

b. Release the latches to open front cover.

c. Put down front cover gently.

2. Routing the power wires is possible through the bottom or rear of the enclosure.

Select the location to route the power wiring.

Bottom-fed wiring:

a. Feed the wires from the underside. Make sure the wiring can sufficiently reach the connec-

tors before securing.

b. Continue with the fastening of the wires, see the following step.

Rear-fed wiring:

a. Remove the waterproof cap from the back of the enclosure and insert the waterproof cap in

cable access location on the bottom of the enclosure.

b. Proceed with the following steps.

Water proof cap

!

1 3 5 7 (13) 1 3 5 7

A1 A 1

A2 A 2

2 4 6 8 (14) 2 4 6 8

Making the Connection

Installation and Operation Manual

14

CAUTION!

BACK-FED WIRING MAY CAUSE THE RISK OF WATER LEAKAGE. DO NOT CHOOSE THIS WIRING

CONNECTION IN OUTDOOR LOCATIONS.

3. Fasten cable gland to secure wires.

Note:

To insure protection from the elements, make sure to use certified IP55 (or above) cable

glands.

4. Remove lid of terminal block and connect the wiring to the correct terminals. See the following

information for specific model connections.

Wiring requirements are dependent on the model type and between single and three-phase

models.

WARNING!

Cable color coding may be defined differently depending on the region.

!

L N

PE

1 3 5 7( 13) 1 3 5 7

A1

1 3 5 7 (13) 1 3 5 7

A

1

A

1

A2

2 4 6 8( 14) 2 4 6 8

A

2

A

2

2 4 6 8 (14) 2 4 6 8

Making the Connection

Installation and Operation Manual

15

Single-phase

Wiring the 240 / 277V Models

 Conduit hub and conduit size M50 according to EN 61386-24.

 Connect the power wires of 2 x RNB70-10 ring terminal with cable lugs to the input termi-

nal marked with "L" and "N" using 2 x M10.0 screws with 88.4 lb-in Torque force.

 Connect the ground wire of RNB14-6 into the earth terminal marked with ground symbol

( ) using 1 x M6.0 screw with 17.7 lb-in Torque force.

Three-phase

Wiring the 480V Model

 Conduit hub and conduit size M50 according to EN 61386-24.

 Connect the power wires of 4 x RNB14-6 ring terminal with cable lugs to the input terminal

marked with "L1", "L2", "L3" and "N" using 4 x M6.0 screws with 28.7 lb-in Torque force.

 Connect the ground wire of RNB14-6 into the earth terminal marked with ground symbol

( ) using 1 x M6.0 screw with 17.7 lb-in Torque force.

Wiring the 208V Model

 Conduit hub and conduit size M50 according to EN 61386-24.

L N

PE

1 3 5 7( 13) 1 3 5 7

A1

1 3 5 7(13)

A1

1 3 5

A1

7(1 3)

1

3 5 7(13)

A1

A2

2 4 6 8( 14) 2 4 6 8

A2

2 4 6 8( 14)

A2

2 4 6

A2

4 6 8(14)

8(1 4)

2

La page charge ...

Delta EIDWU25TSUB02 Manuel utilisateur

Delta EIDWU25TSUB02 Manuel utilisateur

dans d''autres langues

Autres documents