Real Flame C11810LP-BF Mode d'emploi

If the information in this manual

is not followed exactly, a ﬁ re or

explosion may result causing

property damage personal injury

or loss of life.

Installation and service must be

performed by a qualiﬁ ed installer,

service agency or gas supplier.

Improper Installation, adjustment,

alteration, service or maintenance

can cause injury or property

damage.

Read the installation, operation

and maintenance instructions

thoroughly before installing or

servicing this equipment.

Save these instructions for

future reference. If you are

assembling this unit for

someone else, give this manual

to him or her to read and save

for future reference.

! !

IMPORTANT

WARNING

SAVE THESE

INSTRUCTIONS

!

DANGER

If you smell gas:

gas to the appliance.

2. Extinguish any open ﬂ ame.

3. If odor continues, keep away from the appliance and

immediately call your gas supplier or ﬁ re department.

!

WARNING

Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any

other appliance.

An LP-cylinder not connected for use should not

be stored in vicinity of this or any other appliance.

For outdoor use only. DO NOT use

for cooking. DO NOT use under any

overhead enclosure.

USC

For Technical Support Please Contact Real Flame®A t: 1-800-654-1704

C11810LP Sedona

Round Fire Table Owner’s Manual

Lot: _______________

P.O. _______________

2

!

DANGER

This appliance can produce carbon

monoxide which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed

space such as a camper, tent, car or home.

CARBON MONOXIDE HAZARD

TABLE OF CONTENTS

Important Safety Information 3

Propane (LP) Dangers and Warnings 5

Hose & Regulator Assembly and Replacement 7

Parts List 8

Care and Cleaning 14

Gas Component Checks 15

Troubleshooting 17

Warranty 19

Lighting Instructions 13

Pre-Use Instructions 12

Assembly Instructions 9

3

IF YOU SMELL GAS

gas supply to the ﬁ re table.

• Extinguish any open ﬂ ame.

• Do not try lighting any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone.

• Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

• WARNING Failure to follow the dangers, warning and cautions in this manual may

result in serious bodily injury or death, or in a ﬁ re or an explosion causing damage to

property.

• IMPORTANT NOTICE Read and understand all warnings and precautions prior to

assembly and use of your gas ﬁ re table. Improper installation, adjustment, alteration,

service or maintenance can cause injury or property damage.

• Note The use and installation of this product must conform to local codes. In the

absence of local codes, use the National Fuel Gas Code, ANSI Z21.97. Reference to

Natural Gas and Propane Installation code CSA B149.1 or Propane Storage and

Handling code B149.2.

•Minimum Clearance from Unit to Combustible Materials

72”(182.9cm) from the top; 48” (121.9 cm) from all sides and back. Do not locate this

ﬁ re table under any overhead enclosure.

• This gas ﬁ re table and its individual shut

valve must be disconnected from the gas

supply piping system during any pressure testing of that system at test pressures in

excess of 1/2 psi (3.5 kPa). The appliance must be isolated from the gas supply

piping system by closing its individual manual shut

valve during any pressure

testing of the gas supply piping system at test pressures equal to or less than 1/2 psi

(3.5 kPa).

• Keep these instructions for future reference. If you are assembling this unit for

someone else, give this manual to him or her to read and keep for future reference.

• This gas ﬁ re table must be used ONLY outdoors in a well-ventilated space and shall

NOT be used inside a building, garage, or any other enclosed area.

• DO NOT use this outdoor gas ﬁ re table for indoor heating. TOXIC carbon monoxide

fumes can accumulate and cause asphyxiation.

• NEVER LEAVE this gas ﬁ re table unattended when in use.

• Children should be alerted to the hazards of high surface temperatures and kept at a

safe distance while your ﬁ re table is in use.

• Do not store or use gasoline or other ﬂ ammable vapors and liquids within 25 feet

(7.62m) of this or any other appliance.

• Do not store any combustible materials in the base enclosure.

• The use of alcohol, prescription or non-prescription drugs may impair an individual’s

ability to properly assemble or safely operate this outdoor ﬁ re table.

IMPORTANT SAFETY INFORMATION

!

WARNING FIRE TABLE IS FOR OUTDOOR USE ONLY

4

• DO NOT use in an explosive atmosphere. Keep gas ﬁ re table area clear and free from

combustible materials, gasoline and other ﬂ ammable vapors and liquids.

• This outdoor ﬁ re table is NOT to be operated by children. Young children should be closely

supervised when in the vicinity of this outdoor ﬁ re table.

• This outdoor ﬁ re table is not to be installed or used in or on recreation vehicles and/or boats.

• Always use in accordance with all applicable local, state and national codes. Contact your local

ﬁ re department for details on outdoor burning.

• Use the same precautions you would with any open ﬁ re when using this outdoor ﬁ re table.

• DO NOT burn solid fuels such as: wood, charcoal briquettes, lump charcoal, manufactured

logs, driftwood, trash, leaves, paper, cardboard, plywood, painted or stained or pressure

treated wood in this outdoor ﬁ re table.

• DO NOT use this outdoor ﬁ re table until it is COMPLETELY assembled and all parts are

securely fastened and tightened.

• DO NOT store another LP gas tank within 10 feet (3.05 m) of this outdoor ﬁ re table while it is

in operation.

• DO NOT use this outdoor ﬁ re table near automobiles, trucks, vans or recreational vehicles.

• DO NOT use this outdoor ﬁ re table under any overhead structure or near any unprotected

combustible constructions. Avoid using near or under overhanging trees and shrubs.

• Always use this outdoor ﬁ re table on a hard, level non-combustible surface such a concrete,

rock or stone. An asphalt or blacktop surface may not be acceptable for this purpose.

• DO NOT use this outdoor ﬁ re table if any part has been under water. Immediately call a

qualiﬁ ed service technician to inspect the ﬁ re table and to replace any part or control system

and any gas control which has been under water.

• DO NOT wear ﬂ ammable or loose clothing when operating this outdoor ﬁ re table.

• DO NOT use in windy conditions.

• Keep all electrical cords away from a hot outdoor ﬁ re table.

• Certain areas of this outdoor ﬁ re table when in use will become too hot to touch. Do not touch

hot surfaces until the unit has cooled unless you are wearing protective gear such as insulated

pot holders or heat resistant gloves or mittens to avoid burns.

• DO NOT hang or place clothing or other ﬂ ammable materials on or near the gas ﬁ re table.

• Any guard or other protective device removed for servicing the ﬁ re table must be replaced

prior to operating the ﬁ re table.

• DO NOT attempt to move or store this outdoor ﬁ re table until all parts are cool.

• DO NOT lean over this outdoor ﬁ re table when lighting or when in use.

• Use only the regulator and hose assembly provided. The replacement regulator and hose

assembly shall be that speciﬁ ed by the manufacturer.

• DO NOT attempt to disc

onnect the gas regulator from the tank or any gas ﬁ tting while the

outdoor ﬁ re table is in use.

• Alway

gas supply at the tank valve and disconnect regulator from the tank when the

ﬁ re table is not in use

• DO NOT sit on the mantle when the unit is in operation.

• DO NOT throw anything onto the ﬁ re when the unit is in operation.

• Lava rocks are very hot; please keep the children or pets away at a safe distance.

• It is essential to keep the outdoor ﬁ re table valve compartment, burners, and circulating air

passages clean. Inspect outdoor ﬁ re table before each use.

•Prior to each ﬁ re table operation, check the hose for evidence of excessive abrasion or wear

by looking through the visual check hole. If the hose is damaged, cracked or cut, it must be

replaced before using the gas ﬁ re table. The hose assembly can only be replaced with a hose

assembly speciﬁ ed by the manufacturer. Please call Real Flame at 1-800-654-1704.

IMPORTANT SAFETY INFORMATION (continued)

5

•Before each use, remove the lava rocks. Examine the burner and its components. If dirty,

clean with a soft brush and soapy water solution. Examine the area around the burner; any

dirt or foreign material, such as spider webs or nests in this area should be removed. If it is

evident that the burner is damaged, the ﬁ re table must not be used. The burner assembly

cannot be replaced. Please contact Real Flame at 1-800-654-1704 for technical support.

• Place the hose out of the pathways where people may trip over it. Do not place the hose

in areas where it may be subjected to accidental damage.

LP GAS

LP gas is ﬂ ammable and hazardous if handled improperly. Become aware of the

characteristics before using any LP gas product.

Propane Characteristics

• Flammable, explosive under pressure, heavier than air and settles in pools in low areas.

• In its natural state, propane has no odor. For your safety, an odorant has been added.

• Contact with propane could burn your skin.

• Propane is extremely ﬂ ammable and hazardous if handled improperly.

LP GAS WARNINGS

• Cylinders must be stored outdoors in a well-ventilated area out of reach of children.

• Disconnected cylinders must have threaded valve plugs tightly installed and must not be

stored in a building, garage or any other enclosed area.

• Never use a propane cylinder with a damaged body, valve, collar or footing.

• Dented or rusted propane cylinders may be hazardous and should be checked by your

propane gas supplier.

• Be sure to use only one 20 lb (9.1 kg) LP gas cylinder with a Type 1 valve with this

appliance as required by the American National Standards Institute (ANSI) and the

Canadian Standards Steering Committee.

• Only tanks marked “propane” may be used.

• The LP gas supply tank must be constructed and marked in accordance with the

Speciﬁ cations for LP gas LP gas tanks of the U.S. Department of Transportation (DOT) or

the National Standard of Canada, CAN/CSA-B339, LP gas tanks, Spheres and Tubes for

the Transportation of Dangerous Goods; and Commission.

• LP gas tank must be arranged for vapor withdrawal.

• The LP gas tank must have a listed overﬁ lling prevention device (OPD) and a QCCI or

Type I (CGA810) LP gas tank connection.

ATTENTION: Any alteration of the outdoor ﬁ re table that is not speciﬁ cally directed in the

operations manual will void manufacturer warranty.

IMPORTANT SAFETY INFORMATION (continued)

PROPANE (LP) DANGERS AND WARNINGS

!

WARNING

T

Natural Gas (NG) must be done with the approved Real Flame conversion kit and must be

done by a gas professionial. Failure to do so may result in property damage, injury, or death.

his ﬁre table is for use with liqueﬁed petroleum (LP) gas only. The conversion to

6

• The LP gas tank must have a tank collar to protect the tank valve.

• LP gas cylinder must contain a shut-o

valve as speciﬁ ed in the Standard for Compressed

Gas Cylinder Valve Outlet and Inlet Connection, ANSI/CGA-V-1-1977, CSA B96.

• The LP gas tank should not be dropped or handled roughly.

• Tanks must be stored outdoors out of the reach of children. Do NOT store in a building,

garage, or any other enclosed area.

• Never store your LP gas tank where temperatures can reach over 125°F.

• Do not store the LP gas cylinder in direct sunlight or near a source of heat or combustion.

• Never keep a ﬁ lled LP gas tank in a hot car or car trunk. Heat will cause the gas pressure

to increase, which may open the relief valve and allow gas to escape.

• Place dust cap on valve outlet whenever the LP gas tank is not in use. Only install the

type of dust cap on the LP gas tank valve outlet that is provided with the LP gas tank

valve. Other types of caps or plugs may result in leakage of propane.

a. Do not store a spare LP gas cylinder under or near this appliance.

b. Never ﬁ ll the LP gas cylinder beyond 80% full.

c. If the information in (a) and (b) is not followed exactly, a ﬁ re causing death or

serious injury may occur.

• LP gas cylinders should be ﬁ lled only by a certiﬁ ed LP gas dealer.

• The pressure regulator is set for 11 inches of water column (pressure).

• The maximum inlet gas pressure for this outdoor ﬁ re table is 14 inches of water column pressure.

• Never attempt to attach this appliance to the self-contained LP gas system of a camper trailer,

motor home or house.

• Always use the pressure regulator and hose assembly provided with the appliance to connect to

a LP gas cylinder. Never connect to an unregulated LP gas supply. For technical support contact

Real Flame at 1-800-654-1704.

• Hand turn the manual gas control valve. Never use tools. If the valve will not turn by hand, do not

try to repair it. Call a Certiﬁ ed Gas Technician. The use of force or any self attempted repair may

result in a ﬁ re or explosion.

Connecting your gas cylinder

Before connection, be sure that there is no debris caught in the head of the gas cylinder, head of

the regulator valve or in the head of the burner and burner ports. Connect regulator valve and

hand-tighten ﬁ rmly. Disconnect the propane cylinder from the regulator valve when the ﬁ re table

is not in use. DO NOT obstruct the ﬂ ow of combustion air and ventilation air to the burner.

PROPANE (LP) DANGERS AND WARNINGS

7

HOSE & REGULATOR ASSEMBLY AND REPLACEMENT

1. This ﬁre table comes equipped with a standard LP gas hose and regulator including the

appliance side connection for a CGA No 791 Cylinder Connection Device. The LP gas hose and

regulator supplied with this ﬁre table must be used. Only a hose and regulator speciﬁed by

manufacturer can be used for replacement.

a. The CGA No 791 connection incorporates a magnetic ﬂow limiting device that acts to limit

the ﬂow of gas if a leak is detected between the regulator and the burner valve.

b. If the burner valve is open prior to the LP gas cylinder service valve being opened, the

connection will interpret this free ﬂow of gas to be a leak.

c. The connection safety feature will reduce gas ﬂow from the regulator to the appliance to a

minimal level.

d. Be sure that the burner control valve is closed prior to opening the LP gas cylinder service

valve to ensure that the connection ﬂow limiting device is not triggered mistakenly.

e. If the connection ﬂow limiting device is triggered mistakenly, close the LP gas cylinder

service valve and the burner valve, wait 10 seconds to allow the device to reset, open the

cylinder service valve, then open the burner valve and light the ﬁre table as per lighting

instructions.

2. Be sure to protect the hose from any hot surfaces. Serious danger may result if the hose

contacts any hot surface.

3. Regular maintenance of the hose and regulator:

a. Inspect the hose before each use of the ﬁre table.

Use a handheld mirror to see hose sections

located under the unit.

If the hose shows signs of cracks, abrasions, cuts or damage of any

kind, do not operate the ﬁre table. Fix or replace the hose as required before using the

ﬁre table. For assistance with repair or replacement of the hose, call Real Flame at

1-800-654-1704. Use only replacement parts from the manufacturer.

b. Inspect the seal inside the CGA No 791 service valve on the LP gas cylinder when replacing

the cylinder or at least once per year. If there is any indication of damage, have the seal

replaced by a certiﬁed gas dealer before operating the ﬁre table.

4. Do not use tools to tighten the CGA No 791 connection nut onto the LP gas cylinder service

valve. Hand tighten only.

5. Be careful to not cross the threads on the connection when tightening the CGA No 791

connection on to the LP gas cylinder service valve.

6. “Leak Test” should always be performed after attaching the connection to the LP gas cylinder

service valve. (See “Checking for Leaks” section of this manual on page 12)

7. For the connection of the hose and regulator to the LP tank, refer to the “Connection” section

of the LP gas cylinder section above.

8

Parts List

Fire Table

Lava Rock 118137100

Battery N/A

Tank Seat 100260000 1

LP Regulator and Hose 100190000 1

Feet 06000003

Protective Cover 118100007

1 5

2

6

3

7

4

7

3

1

Conversion Kit 00023109S

8

1

1N/A

5

1

2

3

44

8

00023103

6

9

ASSEMBLY INSTRUCTIONS

1

Install the AAA battery as shown in the diagram below.

2

1. Place the tank seat on the ground and place a 20 lb. propane tank

into the tank seat.

2. Tighten down the screw on the side of the tank seat to secure the

propane tank.

1

2

4

+

-

1

44

10

3

4

Check to make sure there is no debris

in the head of the LP gas tank or in the

head of the regulator valve. Make sure you

check the burner and burner ports as well.

Connect gas line to tank by turning knob

clockwise. Hand tighten only.

Make sure the valve on the LP gas tank is

OFF.

Disconnect by turning the knob counter

clockwise until it is detached from the valve.

Connecting the LP Gas Tank

Disconnecting the LP Gas Tank

ASSEMBLY INSTRUCTIONS

11

ASSEMBLY INSTRUCTIONS

5

Place ﬁller material by hand. DO NOT dump bag out into tray to avoid clogging

the burner with dust. Position the lava rock or other approved ﬁller material across

the burn area to a level 1” above the burner. Make sure that you do not block the

igniter housing with ﬁller to ensure proper ignition.

7

1

Ignitor Housing

Lava Rock and Alternate Filler Warning:

2.

Do not light or use this ﬁre table if ﬁller is wet. Ensure ﬁller is completely dry before lighting.

Intense heat can cause wet ﬁller to explode and hit someone causing injury.

3. Please keep away from the ﬁre table for at least 20 minutes during initial start-up as ﬁller

could retain some moisture from manufacturing and shipping.

1. Do not overﬁll the burner area ﬁller materials. The depth of the ﬁller should not be

more than one inch above the burner tube. Only Real Flame ﬁller products have been

certiﬁed and tested by CSA for safe use with this Real Flame ﬁre table. Using other ﬁller

material may result in increased popping/ and cracking or increased CO gas emission.

Additional ﬁller materials such as glass or pumice stone are available for purchase

through Real Flame. Contact Real Flame for pricing and options.

NOTE

12

Please refer to diagram for proper installation.

If the burner pipe does not rest ﬂ ush to the oriﬁ ce

please contact Real Flame at 1-800-654-1704 for

assistance.

CHECKING FOR LEAKS

Make a leak check solution by mixing 1 part dish

washing soap with 3 parts water in a spray bottle.

Make sure control knob is “OFF.” Then, turn LP gas

tank to “ON” at valve.

Spray leak solution on valve connections paying

particular attention to the areas indicated by arrows.

If any bubbles appear turn LP gas tank OFF,

reconnect and re-test. If you continue to see bubbles

after several attempts, disconnect LP gas source and

contact Real Flame at 1-800-654-1704 for assistance.

If no bubbles appear after one minute turn tank OFF,

wipe away solution and proceed.

PRE-USE INSTRUCTIONS

6

Oriﬁ ce is located

in this connection

Check for leaks at these locations

Burner Pipe

!

WARNING Before using this outdoor ﬁ re table, make

WARNING Failure to inspect this connection or

sure you have read, understand and are following all

information provided in the Important Safety Information

section of this manual. Failure to follow those instructions

can cause death, serious injury or property damage.

follow these instructions could cause a ﬁ re or an

explosion, which can cause death, serious bodily

injury, or damage to property.

Prior to each gas ﬁre table operation, check the hose and

valve for evidence of excessive abrasion or wear.

BURNER CONNECTIONS

Make sure the regulator valve and hose connections are

securely fastened to the burner and the tank. If your unit

was assembled for you, visually check the connection

between the burner pipe and oriﬁ ce. Make sure the burner

pipe ﬁ ts over the oriﬁ ce.

13

LIGHTING INSTRUCTIONS

1. Read and understand all operating instructions before lighting

Ensure that all protective ﬁ lm has been removed from stainless

burn tray prior to lighting.

2. Burner control knob must be in the OFF position.

3. Connect propane (LP) cylinder (see previous pages).

4. Slowly open valve on LP gas cylinder.

5. Push and hold ignitor button to create sparks.

6. While holding the ignitor button with one hand, use your other

hand to push and turn the control knob to the LIGHT position

to light the burner.

7. Keep Burner Control Knob pressed in for 15-30 seconds after

ignition.

8. If ignition does not occur in 30 seconds, turn control knob to the

OFF position and turn gas o at the source, wait 5 minutes until

gas has cleared and repeat lighting procedure.

9. After lighting, rotate the Burner Control Knob counter clockwise

to LOW setting. Observe ﬂ ame, make sure all burner ports are

lit. Flame height should be no higher than 13 inches tall.

10. Adjust the ﬂ ame to the desired height with the

control knob.

Using a Long Match or Lighter

1. Prior to lighting, use a shovel to move lava rocks for

access to the burner.

2. Wearing heat resistant gloves, position the burning

long match or burning butane lighter near the side of

the burner. DO NOT lean over the ﬁ re table while

lighting!

3. Turn control knob counterclockwise to LIGHT.

4. Remove long match/long butane lighter.

5. After lighting, use a shovel and heat resistant gloves

to carefully move the lava rocks back into their proper

position.

6. After lighting, rotate the Burner Control Knob counter

clockwise to LOW setting. Observe ﬂ ame, make sure

all burner ports are lit. Flame height should be no

higher than 13 inches tall.

7. Adjust the ﬂ ame to the desired height with the control

knob.

When using this method to light

your ﬁ re table use heat resistant

gloves and follow the step by

step instructions. Failure to do so

could result in severe injury.

If burner ﬂ ame goes out during operation, immediately

turn the control knob OFF and let the gas clear a

minimum of 5 minutes before attempting to re-light the

ﬁ re table.

Please refer to the trouble shooting pages for

additional support, beginning on page 17.

Using the Igniter

!

WARNING

HI

OFF

LIGHT

LOW

Control Knob

PUSH

IN

14

CARE AND CLEANING

Inspecting

WARNING

DO NOT USE SOLVENTS while in closed spaces or while smoking.

!

1. Make sure all parts are securely fastened in place. If a part moves when touched, check its connection points to

see if they are lose.

WARNING DO NOT tamper with this appliance. This is DANGEROUS and will void the warranty. Any part found to

Real Flame at: 1-800-654-1704.

2. Check all gas connections for leaks.

3. Check ignition system to insure proper sparking.

4. Check components for any signs of damage, rust or excessive wear.

5. If damage to any component is detected, DO NOT operate until the proper repairs have been made.

cool to the touch.

General Care and Cleaning

WARNING

DO NOT use oven cleaner or abrasive cleaners as they will damage this product.

1. Wipe exterior surfaces with a mild dishwashing soap, then rinse clean with water.

Storage:

WARNING

1. Turn gas OFF at tank connection. Remove tank and store in a cool, dry location outdoors, away from children.

2. Carefully remove ller and store components at to protect them from breakage.

3. ALWAYS cover your re table when not in use. The cover will protect the mechanical components

from dirt and debris, prevent water from pooling on surface of the re table and will prevent fading and

discoloration of the nish.

4. Store in a cool, dry location away from children and pets.

Table

DO NOT inspect this re table until the re is COMPLETELY out.

This re table must be inspected regularly to ensure that the product is safe to use and to extend product life.

be faulty must be replaced with an approved part, conrmed by the manufacturer. For technical support contact

1. This re table should be cleaned regularly to ensure safe use and extended product life.

NOTE: After repeated use, a slight discoloration of the nish may occur.

DO NOT attempt to clean this re table unless the re is completely out and the unit is

15

Igniter

Housing

Burner

Tube

Do not cover

housing

CORRECT

INCORRECT

GAS COMPONENT CONNECTION CHECKS

If the burner will not light or stay lit, please perform the following checks.

1. Make sure the electrode wire is completely and correctly connected.

2. Make sure that the igniter housing is unobstructed.

Clear any debris on top of the igniter housing and make sure there is no debris

between the igniter pin, thermocouple and the burner tube.

Back of

Electronic

Ignition

16

GAS COMPONENT CONNECTION CHECKS

3. Make sure that the igniter pin and thermocouple are correctly positioned.

- The igniter pin should be pointed at the thermocouple.

- The thermocouple should be positioned 5mm away from the burn tube.

4. Make sure that the thermocouple wire is correctly positioned. The thermocouple

wire should be in line with the valve.

Thermocouple Wire

Wire should

be in line

with valve

Valve

Igniter

Thermocouple

Igniter Box

Thermocouple

Wire

Valve

17

Possible Cause 1: No Gas Flow.

-Check if the LP gas tank is empty. If empty, replace and reﬁ ll. If the propane

tank is not empty, refer to “Problem: Sudden drop in gas ﬂ ow” on the

following page.

Possible Cause 2: Coupling nut and regulator not fully connected.

-Turn the coupling nut about one half to three fourths of a turn, until you

feel a solid stop. Do not use tools, tighten by hand only.

Possible Cause 3: Obstruction of gas ﬂ ow.

- Check for bent or kinked hose.

Possible Cause 4: Spider webs or insect nest in the Venturi.

- Clean the Venturi using compressed air.

Possible Cause 5: Burner ports clogged or blocked.

-Reference “Problem: Irregular ﬂ ame pattern” on the

following page. Clean the burner

ports as described there.

Possible Cause 1: Electrode and burners are wet.

-Wipe dry with cloth.

Possible Cause 2: Igniter battery is dead or backwards.

-Check that the AAA battery is inserted correctly in the igniter (see page 9) or replace the

battery.

Possible Cause 3: Igniter Pin cracked or broken - sparks at crack.

-Call Real Flame at 1-800-654-1704 for technical support.

Possible Cause 4: Wire loose or disconnected.

-Reference page 15, step 1, reconnect wire. Call Real Flame at 1-800-654-1704.

Possible Cause 5: Wire is shorting (sparking) betw een igniter and electrode.

-Call Real Flame at 1-800-654-1704 for support.

Possible Cause 6: Igniter Pin not pointing at thermocouple.

-Reference page 16, turn electrode to point at

the thermocouple.

Possible Cause 7: Bad Igniter.

-Call Real Flame at 1-800-654-1704 for

support.

TROUBLESHOOTING

Problem: Burner will not light using igniter

Problem: The Fire Table emits a lot of black smoke when in use

Problem: Burner will not light with match

Possible Cause 1: Hose from gas ﬁ re table is pinched.

-Make sure the hose is not pinched between the ﬁre table and the source of the gas.

Possible Cause 2: Flame is being obstructed at burner ports.

-Make sure that the gas ports on the burner are free of any glass ﬁller so that the ﬂame

For Technical Support Contact Real Flame at: 1-800-654-1704

can ﬂow naturally.

Venturi Opening

18

Possible Cause: Burner ports are clogged or blocked.

-Clean burner ports.

Do this by inserting a paperclip into each of the burner ports to ensure they are

not clogged.

WARNING: Make sure burner is not on and the gas supply has been properly

disconnected. Allow 15 minutes for unit to cool before touching it.

If these troubleshooting steps are unable to resolve the problem,

please call Real Flame at: 1-800-654-1704

Possible Cause 1: High or gusting winds.

-Do not use ﬁre table.

Possible Cause 2: Low on LP gas.

-Replace or reﬁ ll LP gas tank.

Possible Cause 3: Excess ﬂ ow valve tripped.

-Refer to “Problem: Sudden drop in gas ﬂ ow”

Possible Cause 1: Ice has built up on the outside of the LP gas tank because the

vaporization process is too low.

-Turn the control knob and the LP gas tank to OFF. Replace with a spare LP

gas tank and resume burning. Store the spare LP gas tank in a well ventilated

area, away from children.

Possible Cause 1: Out of gas.

- Reﬁll or exchange your LP tank.

Problem: Sudden drop in gas ﬂ ow, or a reduced ﬂ ame height

Problem: Irregular ﬂ ame pattern, ﬂ ame does not run the full length of the burner

Problem: Flame blow out

Problem: Flame seems to lose heat when burning in cold weather -

temperature below 50°F

TROUBLESHOOTING

19

Warranty & Return Policies

Real Flame®

7800 Northwestern Ave.

Racine, WI 53406

Customer Service: 1-800-654-1704 in USA

Service à la clientèle: 1-800-363-6443 in Canada

custserv@realﬂame.com

Warranty

Real Flame® Company warrants Real Flame gas ﬁreplaces and accessories to be free from defects

in parts under normal use and service for a period of 1 year from the date of purchase and defective

from ﬁnish issues for a period of 1 year from the date of purchase. In the event of such defects

Real Flame will, at its option, replace the defective product or refund the purchase price. The

foregoing is the exclusive remedy and Real Flame disclaims all other warranties, including any

implied warranty of merchantability or ﬁtness for a particular purpose. In addition, Real Flame will

not be responsible for consequential damages in excess of the purchase price of the product on

which such liability is based.

Return Policy

You may return your purchase within 90 days of receipt. No refunds will

be issued for incomplete

or unauthorized returns. All returned products must be 100% complete, adequately packaged in

original packaging and in resalable condition. Products that have been assembled or modiﬁed will

not be eligible for return. All items must be returned in their entirety, meaning all items included

must be returned together. No returns or exchanges on discontinued items. Please begin the return

process by contacting the store or company where you bought your Real Flame item.

Replacement Parts

In the event that an item has been lost or damaged, either by the manufacturer or in shipping, you

may request a replacement. Replacement parts are not available for all units and only given at Real

Flame’s discretion. We will assess any damage and ﬁnd a solution, which could include shipping

you a replacement. No replacements are available for discontinued i

tems or repackaged (open

box) products. Please call Real Flame Customer Service at 800-654-1704 for replacement parts

before returning the damaged item. Please have the following information (which can be found in

your instruction manual) ready before you call Customer Service.

• Model Number of Item

• 4-8 digit Part Number

• Lot Code Number

• Shipping Address

• A picture of the damaged item may be requested. Pictures should be

sent to custserv@realﬂame.com

Incorrect Order Received

If you received something other than what you ordered, please contact Real Flame Customer

Service at 800-654-1704 within 48 hours of receiving the item.

Please refer to www.Realﬂame.com for our complete return guidelines and policies.

NTM Propane Warranty_052815

La négligence à suivre

scrupuleusement les instructions

contenues dans ce manuel peut

provoquer un incendie ou une

explosion occasionnant des

dommages à la propriété, des

blessures sérieuses et même la mort.

L’installation et l’entretien doivent

être faits par un installeur qualiﬁ é,

une compagnie d’entretien ou un

fournisseur de gaz.

Une installation, une mise au point,

une modiﬁ cation ou un entretien

inappropriés peuvent occasionner

des blessures ou des dommages à la

propriété.

Lire attentivement les instructions

concernant l’installation, l’utilisation et

l’entretien avant d’installer ou d’utiliser

l’appareil.

Garder ces instructions pour une

consultation future. Si vous assemblez

cet appareil pour quelqu’un d’autre,

lui donner le manuel pour lecture et

consultation futures.

!

IMPORTANT

!

AVERTISSEMENT

!

AVERTISSEMENT

CONSERVER CES

INSTRUCTIONS

!

DANGER

Si vous percevez une odeur de gaz :

1. Couper l’alimentation en gaz de l’appareil.

2. Éteindre toute ﬂ amme nue.

3. Si l’odeur persiste, vous éloigner de l’appareil et

appeler immédiatement votre fournisseur de gaz ou le

service des incendies.

!

AVERTISSEMENT

Ne pas entreposer ou utiliser d’essence, de vapeurs

ou liquides inﬂ ammables à proximité de cet

appareil ou de tout autre appareil.

Une bouteille de gaz PL non connectée et non

utilisée ne devrait pas être entreposée à proximité

de cet appareil ou de tout autre appareil.

Pour un usage extérieur exclusivement.

NE PAS utiliser pour la cuisson. NE PAS

utiliser sous une enceinte couverte.

USC

Pour le support technique S’il vous plaît nous contacter: 1-800-654-1704

C11810LP Sedona

Manuel d’utilisation de la table-foyer

La page charge ...

Real Flame C11810LP-BF Mode d'emploi

Real Flame C11810LP-BF Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents