DoorBird A1121 Series Manuel utilisateur

Marque: DoorBird

Modèle: A1121 Series

Taper: Manuel utilisateur

Page 2-16

Installation Manual

IP Access Control Device

A1121 Series

Seite 17-32

Installationsanleitung

IP Zutrittskontrollgerät

A1121 Serie

VERSION ., MIN. HW .

A1121

Page 33-48

Manuel d‘installation

Système de contrôle

d‘accès IP

Série A1121

Páginas 49-63

Manual de instalación

Sistema de control

de acceso IP

Serie A1121

INSTALLATION MANUAL

Read these instructions carefully before starting to use

any components. Keep the manual so you can refer

to it at a later date if required. If you hand over the

device to other persons for use, please hand over the

operating manual as well.

You can always ﬁnd the most up-to-date version of the

installation manual on www.doorbird.com/support

To make things easier we use the term “device” for the

product “IP Access Control Device A1121” and “mobile

device” for a smartphone or tablet.

Liability

Every care has been taken in the preparation of this

document. Please inform Bird Home Automation

GmbH of any inaccuracies or omissions. Bird Home

Automation GmbH cannot be held responsible for any

technical or typographical errors and reserves the right

to make changes to the product and manuals without

prior notice. Bird Home Automation GmbH makes

no warranty of any kind with regard to the content

of this document, including, but not limited to, the

implied warranties of merchantability and ﬁtness for

a particular purpose. Bird Home Automation GmbH

shall neither be liable nor responsible for incidental

or consequential damages in connection with the

furnishing, performance or use of this material. This

product is only to be used for its intended purpose.

Equipment Modiﬁcations

This equipment must be installed and used in

strict accordance with the instructions given in

the user documentation. This equipment contains

no components that require service by the user.

Unauthorized equipment changes or modiﬁcations

will invalidate all applicable regulatory certiﬁcations

and approvals.

Symbols used

Danger: Indicates a hazardous situation

which, if not avoided, will result in death or

serious injury.

Warning: Indicates a hazardous situation

which, if not avoided, could result in death or

serious injury.

Caution: Indicates a hazardous situation

which, if not avoided, could result in minor or

moderate injury.

NOTICE Notice: Indicates a situation which, if not

avoided, could result in damage to property.

Important: Indicates signiﬁcant information

which is essential for the product to function

correctly.

Note: Indicates useful information which

helps in getting the most out of the product.

• Mounting, installation and servicing work on

electrical devices may only be performed by

a qualiﬁed eletrician. Failure to observe this

regulation could result in the risk of serious

damage to health or fatal injury due to electric

shocks.

• Devices with 110-240 V connection: The device

may only be connected to an easily accessible

power socket outlet. The mains adapter must be

pulled out if a hazard occurs.

• For power supply, only use the original plug-

in mains adapter delivered with the device,

separately available DIN rail power supplies or

a recommended PoE-Switch/PoE-Injector as

speciﬁed in this manual.

• Because of electrostatic charging, direct contact

with the circuit board can result in destruction

of the device. Direct contact with the circuit

board must therefore be avoided at any time.

• Observe the EN 60065 resp. EN 60950 resp. EN

62368 standard.

• Do not use the device if there are signs of

damage to the housing, control elements

or connecting sockets, for example, or if it

demonstrates a malfunction. If you have any

doubts, please have the device checked by an

authorized expert.

• Do not open the device. This voids the warranty

of the device. The device does not contain any

parts that can be maintained by the user. In

the event of an error, please have the device

checked by an authorized expert.

• For safety, approval and licensing reasons (CE/

FCC/IC etc.), unauthorized change and/or

modiﬁcation of the device is not permitted.

• The device is not a toy: do not allow babies and

children to play with it.

• To avoid the danger of suffocation, keep

any packing materials away from babies

and children. Plastic ﬁlms/bags, pieces of

polystyrene, etc. are not a toy and can be

dangerous in the hands of a child. Discard any

packing materials immediately after removing

the product. Do not reuse packing materials.

• Always lay cables in such a way that they do not

become a risk to people and domestic animals.

• Voltage is applied to parts within the

equipment. Do not touch any parts that are

not associated with the installation, wiring, or

connection. Electric shock could result.

• On devices which are not marked as weather-

proof: Keep the device away from water or any

other liquid.

Hazard information

WARNING

ENGLISH

• Do not install or make any wire terminations

while power supply is plugged in. It can cause

eletric shock or damage to the device.

• Before turning on power, make sure wires are

not crossed or shorted. If not, ﬁre or eletric

shock could result.

• High voltage may be present internally. Do not

open the device. Electric shock could result.

• The device is not of explosion-proof. Do

not install or use near gases or ﬂammable

materials. Fire or explosion could result.

• Do not install two power supplies in parallel

to a single input. Fire or damage to the device

could result. Be sure to connect a single power

supply to the device.

• Do not connect any terminal on the device to

an AC power line. Fire or electric shock could

result.

• Keep AC cord from being marred or crushed.

If the AC cord is fractured, ﬁre or electric shock

could result.

• Do not plug or unplug with wet hands. Electric

shock could result.

• Do not put any metal or ﬂammable material

into the device. Fire, electric shock, or device

trouble could result.

• Existing wiring may contain high voltage AC

electricity. Damage to the device or electric

shock could result. Wiring and installation

must be done by a qualiﬁed eletrician.

• When mounting the device on a wall or

ceiling, install the device in a convenient

location, but not where it could be jarred or

bumped. Injury could result.

• On devices with ground terminals, connect to

an earth ground. Otherwise ﬁre or malfunction

could result.

• On devices with plastic or real glass, do not put

high pressure on the glass. If fractured, injury

could result.

• On devices with LCD, if LCD is punctured, do

not allow contact with the liquid crystal inside.

Injury could result. If necessary, gargle your

mouth and clean your eyes or skin with clear

water for at least 15 minutes and consult your

doctor.

• Do not put anything on the device or cover

the device with cloth, silicone, glue, coating,

separate covering etc. Fire or device issues

could result.

• Do not install the device in any of the following

locations. Fire, electric shock, or device trouble

could result.

 Places under direct sunlight or places near

heating equipment that varies in temperature.

 Places subject to dust, oil, chemicals, hydrogen

sulﬁde (hot spring).

 Places subject to moisture and humidity

extremes, such as bathrooms, cellars,

greenhouses, etc.

 Places where the temperature is very low, such

as inside a refrigerated area or in front of an air

conditioner.

 Places subject to steam or smoke (e.g. near

heating or cooking surfaces).

 Where noise generating devices such as

dimmer switches or inverter electrical

appliances are closeby.

 Locations subject to frequent vibration or

impact.

• On devices with intercom, be sure to perform

a call test with low audio volume on both

intercom devices. A sudden call etc. may arrive

causing for example damage to your ear.

• If the device does not operate properly, unplug

the power supply.

• All devices which are not marked as weather-

proof are designed for indoor use only. Do not

use outdoor.

• On devices which are marked weather-proof:

Do not spray with high-pressure water. Device

issues could result.

• We do not assume any liability for damage to

property or personal injury caused by improper

use or the failure to observe the hazard

information. In such cases, any claim under

warranty ceases. For consequential damages,

we assume no liability!

WARNING

Safety instructions

• The device shall be used in compliance with

local laws and regulations.

• Store the device in a dry and ventilated

environment.

• Avoid exposing the device to shocks or heavy

pressure.

• Do not install the device on unstable brackets,

surfaces or walls. Make sure the material is

strong enough to support the weight of the

device.

• Use only applicable tools when installing the

device. Using excessive force with tools could

cause damage to the device.

• Do not use chemicals, caustic agents, or

aerosol cleaners.

• Use a clean dry cloth for cleaning.

NOTICE

• Use only accessories that comply with

technical speciﬁcation of the device. These can

be provided by Bird Home Automation GmbH.

• Use only spare parts provided by or

recommended by Bird Home Automation

GmbH.

• Do not attempt to repair the device by yourself.

Contact Bird Home Automation GmbH for

service matters.

• Keep the device more than 1 m (3.3‘) away

from microwave, radio, TV, wireless router and

any other wireless devices.

• On devices with intercom or built-in speaker

or built-in microphone or signal transmission

functions, keep the wires more than 30 cm

(12‘‘) away from AC 100-240 V wiring. AC

induced noise and/or device malfunction

could result.

• Install the device in an area that will be

accessible for future inspections, repairs and

maintenance.

• If the device is used close to a cellular phone, the

device may malfunction.

• The device can be damaged if dropped. Handle

with care.

• The device turns inoperative during power

failure.

• On devices with intercom or built-in speaker or

built-in microphone, in areas where cellular or

Radio / TV broadcasting station antennas are

closeby, the device may be affected by radio

frequency interference.

• On devices with LCD screen, it must be noted

in advance that the LCD panel, though

manufactured with very high precision

techniques, inevitably will have a very small

portion of its picture elements always lit or

not lit at all. This is not considered a device

malfunction.

• On devices with intercom, due to the

environmental sound around the device, it

may hinder smooth communication, but this

is not a malfunction.

• On devices with Username/Password, the

Username/Password to access the device is the

customer‘s responsibility. Make sure to use a

password that cannot be easily guessed by a

third party. We recommend that you change

the Password on a regular basis.

• We will, under no circumstances, be liable

for damage that occurs due to failures in

power supply, network equipment or terminal

devices; failures due to Internet providers

and cellular network providers; failures such

as disconnected lines and other losses in

communication, which makes it impossible to

provide this service as well as in any way delay

this service due to any other causes outside of

our responsibility; or if an error or missing data

occurs during transmission.

Transportation

NOTICE When transporting the device, use the original

packaging or equivalent to prevent damage

to the device.

Warranty Information

For information about the device warranty, see

www.doorbird.com/warranty

Information on disposal for users of waste

electrical & electronic equipment (private

household)

This symbol on the products and/or accompanying

documents means that used electrical and electronic

products should not be mixed with general household

waste. For proper treatment, recovery and recycling,

please take these products to designated collection

points, where they will be accepted an a free of charge

basis. Alternatively, in some countries you may be able

to return your products to your local retailer upon the

purchase of an equivalent new product. Disposing

of this product correctly will help to save valuable

resources and prevent any potential negative effects

on human health and the environment which could

otherwise arise from inappropriate waste handling.

Please contact your local authority for further details

of your nearest designated collection point. Penalties

may be applicable for incorrect disposal of this waste,

in accordance with national legislation.

Information on disposal in other countries outside

the European Union

This symbol is only valid in the European Union. If you

wish to discard this product, please contact your local

authorities or dealer and ask for the correct method

of disposal.

ENGLISH

COMPONENTS*

1x Quickstart guide

with Digital Passport

1x Drilling template

1x Disassembly tool for

screw connection terminal

plug

1x Power supply unit (mains adapter)

with four country-speciﬁc adapters

Small parts

1x Installation manual

1x Flush-mounting

housing

(ﬂush-mounted model)

1x Main Electrical Unit

with front panel

1x Wall-mounting bracket

(surface-mounted model)

THIS SIDE UP

* The sketches in this manual may differ from the purchased model.

1) Keypad wit 12 keys

2) Dual frequency RFID reader (125 KHz, 13.56 MHz)

3) Bluetooth transceiver

4) Status icons with Diagnostic LEDs

5) Security screw

6) Wiegand jack

7) Screw connection terminal

8) SETUP Button (SET) of the device to e.g.

conﬁgure the WiFi interface of the device using

the DoorBird App

The ﬂush-mounted model may differ optically.

DEVICE

Front Back

1x RJ45 adapter

WIFI

VIDEOS

Need help with the installation? Be sure to watch our

installation videos which can be found on

http://www.doorbird.com/support

Each individual step of the installation is clearly

documented in the videos.

INSTALLATION

All the steps below should be carried out carefully

by a competent adult, taking into consideration

any applicable safety regulations. Please contact us

directly or seek the advice of a competent specialist.

Please ensure that all wires used for the

installation are undamaged along their entire

length and approved for this type of use.

Network speed and network components

Please ensure that the upload speed of your Internet

connection is at least 0.5 Mbps. The user experience is

only as good as your network speed, network stability

and quality of your network components, such as

your Internet Router and WiFi access points or WiFi

repeaters. Please also make sure that your network

components are no older than two years old, have

been manufactured by a well-known manufacturer,

and have the latest ﬁrmware installed.

Should these requirements not be fulﬁlled, it may

occur that push notiﬁcations are delayed or not

delivered to your mobile device.

Requirements:

High-speed Internet (via landline): DSL, cable or optical

ﬁbre

Network: Ethernet, with DHCP

SWITCHING OFF POWER

Switch off the power to all wires leading to

the assembly location, e.g. power supply for

the device or an electrical door opener.

DISMANTLING THE EXISTING

ACCESS CONTROL DEVICE

Should there already be an access control device on

the exterior wall of the house, please remove it.

DETERMINING THE ASSEMBLY

LOCATION

NOTICE Do not expose the device to direct sunlight.

The housing temperature can exceed the

maximum allowed temperature limit. This

can result in damage of electric and

mechanic components of the device and

injuries especially when touching exterior

parts of the device. White and bright

silver-colored front plates absorb less

sunlight than dark ones.

Any defects caused by direct sunlight are not

covered by warranty.

Important note for cavity mounting (e.g. in

pedestals and mailboxes):

To protect the electronic units, please

ensure that the technical components are

protected against dripping and running

water caused by condensate or entering

the mounting space through openings.

To protect the electronic units, ensure

that the mounting space inside is not

accumulating water.

Sucient air circulation must be ensured,

as well as unobstructed drainage of water

at the base of the installation.

Failure to do so will result in warranty being

declined.

ENGLISH

15 cm

5.91 in

8,5 cm

3.35 in

ASSEMBLING THE MOUNTING HOUSING

The product is available as a surface-mounted, ﬂush-mounted and retroﬁt version. In the ﬂush-mounted

version, the front panel is slightly larger to better cover the hole in the wall, and the mounting housing

(backbox) is made entirely of metal instead of plastic.

In the retroﬁt version, the front panel is slightly larger to better cover the hole in the existing panel and the

mounting is not realized with a separate mounting housing (backbox) but with metal clamps.

68,00 mm

2.68 in

138,00 mm

5.43 in

26,50 mm

1.04 in

68,00 mm

2.68 in

138,00 mm

5.43 in

26,50 mm

1.04 in

If the wall of the house is not made of wood, you

should drill dowel holes 5 mm (0.19 in) in diameter

in the wall according to the drilling template and

then place the dowels provided into the boreholes.

If you must drill holes in a wall, insert screws into a wall or lever up a wall, ensure that no cables or mains

(gas, water, etc.) are to be found in the wall.

If the wall of the house is made of wood, dowels are not normally required. There are special dowels for

assembling the device on an insulating wall, e.g. Fischer insulating dowels.

If you use the retroﬁt version, cut an appropriate

hole in the existing panel.

If you use the ﬂush-mounted housing, lever up the

wall accordingly.

Flush-mounted model Retroﬁt model

THIS SIDE UP

. MOUNTING

Lead all cables and wires you want to connect to the device through the mounting housing (for retroﬁt version:

through the hole in the existing panel).

. DISASSEMBLING THE FRONT PANEL

(APPLIES ONLY TO THE SURFACE-MOUNTED AND FLUSH-MOUNTED MODEL)

Remove the front panel with the attached Main Electrical Unit carefully from the mounting housing (backbox)

using the orange (Torx+Pin) screw driver provided.

We have designed the front panel and the safety screw in a way that it cannot be screwed through the

front panel so that is does not fall off / get lost during installation..

Turn the safety screw counter-clockwise until it is loose. Pull the front panel with attached Main

Electrical Unit out of the mounting housing (backbox).

Flush-mounted model Surface-mounted model

Please make sure that the outer frame of the ﬂush-

mounted housing rests on the outside of the wall

and that the edge of the ﬂush-mounted housing

is sealed all around against moisture from the

outside.

Before mounting: Pierce through the middle

of the rubber seal for the cable entry using a

screwdriver.

THIS SIDE UP

Retro Fit model

Surface-mounted modelFlush-mounted model

ENGLISH

NETWORK CONNECTION OPTIONS

You can connect the device to the network by either using a WiFi 2.4 GHz

connection or a network cable.

OPTION 

Network cable (recommended, maintenance free)

Install a network cable (which is plugged into a network switch / router

with Internet access) from the inside of your building to the assembly

location. The network cable between the assembly location and the

network switch / router can have a maximum length of 80 m/262 ft (IEEE

802.3). If you must span a distance of more than 80 meters/262 feet you

can put a network switch in between. Make sure to use a high-quality

Cat.5 network cable or better and with proper shielding (Screened Foiled

Twisted Pair (S/FTP or SFTP)) whereby the shield is connected to the outer

metal shield of the RJ45 plug (8P8C).

The device itself does not have an RJ45 socket. The scope of delivery

includes an RJ45 adapter that can be routed out of the housing. As an

alternative, the RJ45 connector of the network cable can be removed

on the device side to connect the wires directly to the Phoenix strip

according to the assignment under point 7 „CONNECTING THE DEVICE“.

OPTION 

WiFI 2.4 GHz

When using WiFi please make sure you have a good WiFi signal at the

assembly location of the device. You can increase the WiFi signal by using

so called “WiFi repeaters”, which can boost your WiFi signal. You should

install such a WiFi repeater close to the assembly location of the device,

typically inside your home and close to the device.

For further information regarding WiFi installations, please visit

www.doorbird.com/wiﬁ

PREPARE POWER SUPPLY

The device does not have a battery as power supply, therefore, choose one

of the following options.

OPTION 

Power supply using the power supply unit (mains adapter)

To power the device using the provided mains adapter, 2 insulated wires

are required. The power supply unit has a 300 cm (9.8 ft) long cable with

two insulated wires. The network connection is then established via a

network cable or alternatively via WiFi.

NOTICE Do not plug the power supply unit into the wall socket yet.

Only use the power supply unit provided along with the device,

or a DIN-rail power supply unit (see “OPTION 3”) that you

can obtain from us separately, since this has been specially

stabilized electrically and is equipped with an integrated audio

interference reduction device. Other power supply units may

destroy the device or cause poor transmission quality. The

warranty automatically expires if you use a different power

supply unit.

The provided mains adapter is only

capable to power one device. It is not

designed to power multiple devices

simultanously.

If you must power more than one device

with one power supply, we recommend

to use a PoE-Switch with PoE Standard

IEEE 802.3af Mode A or an appropriate

DIN rail power supply (see “OPTION 3”).

If you have only two wires available at

the assembly location, you may use the

“DoorBird 2-Wire Ethernet PoE Converter

A1071”, sold separately. It allows you to

transfer network data (Ethernet) and

power (PoE) with a simple two-wire

cable over long distances. For example,

existing buildings with a simple two-wire

bell wire can be equipped with network

technology without having to retroﬁt any

network cables.

For reasons of network stability, we

principally recommend using a network

cable, as WiFi is sensitive to interference

(range, house walls acting as shields, re-

liability of performance, third party WiFi

networks, wireless transmitters causing

interference in the area, etc.).

NOTICE The power supply unit is plugged into a wall socket, usually

where the two wires from your assembly location come out of

the wall in the interior of the house.

The provided mains adapter is not outdoor-ready and for

indoor-use only.

OPTION 

Power supply and network connection using PoE (Power over

Ethernet)

To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-

Injector (e.g. DoorBird Gigabit PoE Injector A1093), use a CAT.5 cable or

higher in accordance with the PoE standard IEEE 802.3af Mode A.

A CAT.5 cable or higher must be used for this purpose, as network signals

can only be transmitted over completely insulated, shielded and twisted

cables. If you use PoE as a source of power, the four wires for PoE then

simultaneously form the data line. The device will not start if your PoE-

Switch/PoE-Injector does not support the PoE Standard IEEE 802.3af

Mode A.

NOTICE Do not combine the power supply from the power supply unit

(mains adapter) with the power supply via PoE.

You can ﬁnd further information about PoE here:

http://www.doorbird.com/poe

1. Disconnect the PoE-Switch or PoE-Injector from the power grid.

2. Place the network cable in the installation site of the device.

If you must power more than one device

with one power supply , we recommend

to use a PoE-Switch with PoE Standard

IEEE 802.3af Mode A or an appropriate

DIN rail power supply (see “OPTION 3”).

Theoretically (not recommended by us!),

an unshielded, but over the whole length

(max. 80 m/262 ft) twisted bell wire with

two pairs of wires (ﬁrst twisted pair of

wires: “T+, T-”, second twisted pair of wi-

res “R+, R-”) can be used for the network

and PoE transmission as an alternative

to a Cat.5 network cable or better. This is

comparable to a Cat.3 network cable. In

this case, however, we cannot guarantee

the data throughput or the stability of

the network connection and power sup-

ply; this must be measured and checked

on site by qualiﬁed personnel over several

hours (network data is transmitted at

high frequency, therefore a shielded

Cat.5 network cable twisted in pairs or

better must normally be used).

For easier installation we strongly

recommend to remove the plug from

screw connection terminal while you

connect the cables and wires.

 CONNECTING THE DEVICE

It is possible to connect the cables and wires to the device conveniently

and safely via the labeled screw connection terminal. You can connect all

necessary cables and wires to the device now.

NOTICE Please remove any cables and wires from the connection ports

of the device that you do not need.

The product comes with a disassembly tool that

allows you to safely remove the connector from the

screw terminal socket. Please do not use any other

tool, e.g. a screwdriver, as this may damage the

circuit board of the device.

OPTION 

Power supply using a DIN rail power supply unit

Alternatively to the mains adapter, we offer DIN rail power supplies in

our online shop, which can be installed by a specialist. The network

connection is then made via a network cable or alternatively via WiFi.

ENGLISH

LAN / POE

D D GND

Wiegand

R R R R  VDC

– +

Port Description

LAN/POE

T+ T- R+ R-

The device does not have an integrated standarized RJ45 socket to ensure ...

• that the device rests as ﬂat as possible on the wall.

• that no wall needs to be levered up.

• that a strong and inﬂexible Cat.6 or Cat.7 installation cable can be used.

Use only four wires (1, 2, 3 and 6) of a standard Network cable Cat.5 or better,

coming from the Internet Router/PoE-Switch/PoE-Injector.

Cat.5 / Cat.6 Network cable

T+ White and orange network cable wire (Number 1, Transmit Data +)

T - Orange network cable wire (Number 2, Transmit Data -)

R+ White and green network cable wire (Number 3, Receive Data +)

R - Green network cable wire (Number 6, Receive Data -)

Cat.7 Network cable (Installation cable)

T+ White network cable wire from pair “orange/white”

(Number 1, Transmit Data +)

T- Orange network cable wire from pair “orange/white”

(Number 2, Transmit Data -)

R+ White network cable wire from pair “green/white”

(Number 3, Receive Data +)

R- Green network cable wire from pair “green/white”

(Number 6, Receive Data -)

NOTICE Do not power the device simultaneously via the power supply from

the power supply unit (mains adapter) and the power supply via PoE.

T+ T- R+ R-

R1, R1 Bi-stable latching relay #1, max. 24 V DC/AC, 1 A. Security feature: The relay

keeps its state even in the case of loss of power. You can conﬁgure the default

state of the relay (open/close) via the DoorBird App. These ports can be used

to connect e.g. an electric door opener. The device does not supply power to

the connected device. The power supply for the electric door opener must be

installed separately.

When wiring an electric door opener directly to the device. There is a

risk that the electric door opener could be tampered by unauthorized

third parties (e. g. by breaking the device and short-circuiting the

wiring of the door opener). Therefore, we generally recommend the

use of a remote safety relay mounted indoors (e. g. DoorBird I/O Door

Controller A1081) for wiring an electric door opener for a more secure

installation in your home.

R2, R2 Bi-stable latching relay #, max. 24 V DC/AC, 1 A. Security feature: The relay

keeps its state even in the case of loss of power. You can conﬁgure the default

state of the relay (open/close) via the DoorBird App. These ports can be used

to connect e.g. an electric door opener. The device does not supply power to

the connected device. The power supply for the electric door opener must be

installed separately.

When wiring an electric door opener directly to the device. There is a

risk that the electric door opener could be tampered by unauthorized

third parties (e. g. by breaking the device and short-circuiting the

wiring of the door opener). Therefore, we generally recommend the

use of a remote safety relay mounted indoors (e. g. DoorBird I/O Door

Controller A1081) for wiring an electric door opener for a more secure

installation in your home.

15 VDC - 15 V DC Power supply input, negative pole (-). Please connect the black wire

of the power supply unit (mains adapter) supplied with this device if you do

not power the device using PoE.

NOTICE Do not power the device simultaneously via the power supply from

the power supply unit (mains adapter) and the power supply via PoE.

15 VDC + 15 V DC Power supply input, positive pole (+). Please connect the red wire of

the power supply unit (mains adapter) supplied with the device here, if you do

not power the device using PoE.

NOTICE Do not power the device simultaneously via the power supply from

the power supply unit (mains adapter) and the power supply via PoE.

D0 Data Low. For Wiegand output (RFID reader, Keypad). Max. 5 mA per output

(data line). Wiegand can be turned on/off and conﬁgured via the DoorBird App.

The Small parts bag provided contains a cable with tree individual wires (black,

green, white) and plug. Please use this cable to connect your Wiegand device

(D0: Green wire).

D1 Data High. For Wiegand output (RFID reader, Keypad). Max. 5 mA per output

(data line). Wiegand can be turned on/off and conﬁgured via the DoorBird App.

The Small parts bag provided contains a cable with tree individual wires (black,

green, white) and plug. Please use this cable to connect your Wiegand device

(D1: white wire).

GND Ground. For Wiegand output (RFID reader, Keypad). Wiegand can be turned

on/off and conﬁgured via the DoorBird App.

The Small parts bag provided contains a cable with tree individual wires

(black, green, white) and plug. Please use this cable to connect your Wiegand

device (GND: Black wire).

ENGLISH

NOTICE Please take care when connecting the cables and wires. Connecting the cables and wires the wrong way

may damage the device. Wires without insolation material must not protrude out of the green screw

connection terminal, it may lead to electrical short and damage the device.

ASSEMBLE THE DEVICE TO THE MOUNTNG HOUSING (BACKBOX)

If you use the surface- or ﬂush-mounted version, assemble the front panel with the attached Main Eletrical

Unit carefully using the orange (Torx+Pin) screw driver provided with the wall mounting-bracket / mounting

housing. Turn the safety screw clockwise until it is hand-tight.

NOTICE Tighten the safety screw by hand only (less than 5 newton meter [Nm]), otherwise the Main Eletrical

Unit housing may be damaged.

If you use the retroﬁt model, assemble the front

panel with the attached Main Eletrical Unit

carefully to the existing panel using the metal

clamps.

Retro Fit model

Surface-mounted modelFlush-mounted model

ACTIVATE THE DEVICE

If the device is to be supplied with power by a mains

adapter, plug the power adapter of the device into

a wall socket. If the device is to be powered via PoE,

switch on the PoE-Switch/ PoE-Injector which is

connected to the device. If the device is to be powered

via DIN-rail power supply, switch on the DIN-rail power

supply.

The Keypad LEDs indicate whether the device is

supplied with power. The LEDs light up in white color

a few seconds after you have connected the device to

the power supply.

If Keypad LEDs do not light up, please check the

power supply. When using a wall-plug power

supply and not PoE, please check whether you have

connected the positive pole and negative pole to the

device correctly.

The device is ready for operation (booting up process,

any software updates, etc.) once it has emitted a short

diagnosis sound (two beeps) from the integrated

piezo speaker and the Diagnostic LEDs light up for

a few seconds in blue color. This may last for up to 5

minutes.

 DOWNLOADING AND INSTALLING

THE APP

Download the “DoorBird” App by Bird Home

Automation onto your mobile device from the Apple

App Store or Google Play Store. You can always ﬁnd

the most up-to-date version of the App manual on

www.doorbird.com/support

If you use WiFi for connecting the device to your

Internet Router, ﬁrst go to the DoorBird App > ”WiFi

Setup“ and follow the instructions.

If you have ﬁnished the WiFi setup or have connected

the device to your Internet Router by means of a

network cable, go to the DoorBird App > “Add device”

and click on the QR code icon in the “User” ﬁeld.

Scan the user QR code found on the “Digital Passport”

provided with the device.

If you have problems adding the device to the App

please check if the device is online ( www.doorbird.

com/checkonline ). If the device is not online, please

check the WiFi or network cable connection again.

DIAGNOSTIC-LEDS

Both LEDs light up blue:

for 5 seconds continuously illuminated

– Device is connected to the internet.

for 30 seconds with ﬂashing intervals of 1 second

– Device has no internet connection.

for 30 seconds with ﬂashing intervals of 3 seconds

– Device has no network connection.

Both LEDs light up yellow:

for 30 seconds with ﬂashing intervals of 1 second

– Device has entered WiFi setup mode

DIAGNOSTIC SOUNDS

The device may emit brief diagnostic sounds after

it has been connected to power supply / network /

Internet, e.g. upon boot process ﬁnished, press of a key,

WiFi Setup Mode enabled, RFID Reader detected tag,

Relay triggered.

TAMPER SENSOR

The device has a built-in tamper sensor that can

be conﬁgured via the app to send an alert over the

network (e.g. a push notiﬁcation) if the device is

moved during operation.

BLUETOOTH TRANSCEIVER

The device has a built-in Bluetooth® transceiver.

We will add further functionality for interesting

applications soon. Please check our company news

blog or the latest version of this manual at

www.doorbird.com/support for updates.

DOORBIRD CONNECT

The device features many options to integrate it into

third-party applications. For information, terms and

conditions see www.doorbird.com/connect

ENGLISH

MAINTENANCE OF THE FRONT PANEL

Cleaning and maintenance instructions

All of our front panels are made of high-quality

materials and are designed for a durable lifetime.

Since this kind of devices are usually installed in

unprotected outdoor areas, they are exposed to

adverse weather conditions and aggressive substances,

especially close to frequently used roads, in coastal

and industrial areas. Therefore, please consider the

following care instructions. Unfortunately, we cannot

accept any liability for damage if these instructions

are not being observed. Aggressive dirt such as bird

droppings should be removed as quickly as possible.

NOTICE Aggressive stains such as bird droppings

should be removed as soon as possible.

NOTICE Never use abrasive detergents such as steel

wool or scouring milk!

Warm water is usually sucient, if necessary with

a little detergent, a soft cloth or brush. Plastic parts

must not be treated with metal care products.

Remove all residues of cleaning agents or lubricants to

avoid stains or discolouration after the maintenance.

Stainless Steel

Only high-quality stainless steel is used for all available

DoorBird devices. However, high-quality stainless steel

can also rust, as approx. 70% of stainless steel is made

of iron. Rust resistance is only achieved by a protective

layer (also called passive layer), which covers the iron

like a skin. This protective layer consists essentially of

chromium and other precious metals.

Iron particles, grinding dust and chips deposited on

stainless steel can lead to corrosion (rust ﬁlm). These

iron particles can be found everywhere, but especially

in coastal and industrial areas and close to frequently

used roads. Please remove ferrous deposits immediately,

as they will attack your device and lead to real rust if

not removed. To remove rust, simply wipe off the dust;

in addition, a care product is recommended, e.g. WD

40, available e.g. at Amazon for less than € 5.00. Simply

apply in a thin layer and rub in. The same applies if rust

appears on the engravings on the stainless steel surface.

Cement or lime splashes should be carefully removed

as soon as possible with a wooden spatula before

hardening.

The following cleaning detergents are not to be used

as they reduce corrosion resistance:

• products containing chloride and hydrochloric

acid

• Bleach (in case of accidental use, rinse thoroughly

with water)

• Silver polish

After the cleaning with clear water wipe with damp

cloth and rub dry to avoid lime traces. Lime residues

can be avoided by using demineralised water.

Stainless steel PVD coated

PVD coated, chrome-plated or gold-plated surfaces are

recommended to be cleaned with a grease-

dissolving detergent and clear water or with a clean

and dust-free microﬁbre cloth. For high-gloss surfaces,

use a scratch-free cloth (e.g. cleaning cloth for glasses,

furniture polishing cloth, etc.).

Lacquered surfaces

Clean painted surfaces and lettering with a soft,

scratch-free cloth moistened with a mild soap solution

(e.g. cleaning cloth for glasses, furniture polishing cloth,

etc.). To prevent stains or discolouration, the detergents

should be wiped off without leaving any residue.

Be particularly careful with lettering in order not to

damage the ﬁlm or the print.

LEGAL NOTES

General remarks

1. DoorBird is a registered trademark of Bird Home Automation

GmbH.

2. Apple, the Apple logo, Mac, Mac OS, Macintosh, iPad, Multi-Touch,

iOS, iPhone and iPod touch are trademarks of Apple Inc.

3. Google, Android and Google Play are trademarks of Google, Inc.

4. The Bluetooth® word mark and logos are registered trademarks

of Bluetooth SIG, Inc.

5. All other company and product names may be trademarks of the

respective companies with which they are associated.

6. We reserve the right to make changes to our products in the

interests of technical advancement. The products shown may

also look different from the products supplied based on ongoing

enhancement.

7. Reproducing or using texts, illustrations and photos from this

instruction manual in any media – even if only in the form of

excerpts – shall only be permitted with our express written

consent.

8. The design of this manual is subject to copyright protection. We

do not accept any liability for any errors or any erroneous content

or printing errors (even in the case of technical specifications or

within graphics and technical sketches).

9. Our products are in compliance with all technical guidelines,

electrical and telecommunications regulations applicable in

Germany, the EU and the USA.

10. Our products and also the components contained therein

(ICs, software, etc.) may only be used for civilian non-military

purposes.

Data privacy and data security

1. For maximum security, the device uses the same encryption

technologies as are used in online banking. For your security, no

port forwarding or DynDNS is used either.

2. The data centre location for remote access over the Internet by

means of an App is obligatory in the EU if the determined Internet

IP-Address location of the device is within the EU. The data centre

is operated in line with the most stringent security standards.

3. Video, audio and any other surveillance methods can be regulated

by laws that vary from country to country. Check the laws in your

local region before installing and using this device for surveillance

purposes.

If the device is a door-, indoor station or camera:

• In many countries video and voice signal may only be transmitted

once a visitor has rung the bell (data privacy, configurable in the

App).

• Please carry out the mounting in such a way that the detection

range of the camera limits the device exclusively to the immediate

entrance area.

• The device may come with a visitor history and motion sensor. You

can activate/deactivate this function if required.

If necessary, indicate the presence of the device in a suitable place

and in a suitable form.

Please observe any relevant country-specific statutory regulations

concerning the use of surveillance components and surveillance

cameras applicable at the installation site.

Check with the property owner and your house community if you are

allowed to install and use this product. Bird Home Automation GmbH

cannot be held responsible for any miss-use or miss-configuration of

this product, including the unauthorized opening of a door.

Bird Home Automation cannot be held responsible for damages

caused by improper existing installations or improper installation.

Software and operating system’s updates (so-called “firmware

updates”) are generally automatically installed on the products of

Bird Home Automation GmbH via Internet, if technically possible.

Automatic firmware updates keep the products‘ software up to date

so that they always work reliably, safely and efficiently. Through

further development, features can be added, extended or slightly

changed. Major changes or limitations to existing features will

generally occur if Bird Home Automation GmbH deems it necessary

(e.g. for data protection, data security or stability reasons, or to keep

them up to date). When a firmware update is available, Bird Home

Automation GmbH‘s servers generally automatically distribute it to

all compatible products connected to the Internet or Bird Home

Automation GmbH‘s servers. This process is gradual and can take

several weeks. As soon as a product receives a firmware update, the

system will be installed and will restart by itself. Installed firmware

updates cannot be undone. Since the products and software of

Bird Home Automation GmbH are not explicitly customer-specific

products, a customer cannot deny an automatic update if the

product is connected to the Internet or to the Bird Home Automation

GmbH’s server.

Publisher

Bird Home Automation GmbH

Uhlandstraße 165

10719 Berlin

Germany

Web: www.doorbird.com

Email: [email protected]

It is possible that these manual still contains typographical errors

or printing errors.The information in this manual will be checked

regularly and corrections will be made in the next version. We accept

no liability for errors of a technical or printing nature and their

consequences.

DEUTSCH

INSTALLATIONSANLEITUNG

Lesen Sie diese Anleitung sorgfältig, bevor Sie die

Komponenten in Betrieb nehmen. Bewahren Sie die

Anleitung zum späteren Nachschlagen auf!

Wenn Sie das Gerät anderen Personen zur

Nutzung überlassen, übergeben Sie auch diese

Bedienungsanleitung.

Die stets aktuelle Version der Installationsanleitung

ﬁnden Sie unter www.doorbird.com/de/support

Zur Vereinfachung der Begriffe verwenden wir „Gerät“

für das Produkt „IP Zutrittskotrollgerät A1121“ sowie

„mobiles Endgerät“ für ein Smartphone/Tablet.

Haftung

Die Erstellung dieses Dokuments wurde sorgfältig

vorbereitet. Bitte infor mieren Sie Bird Home

Automation GmbH über etwaige Ungenauigkeiten

oder Unterlassungen. Bird Home Automation GmbH

kann nicht für tech nische oder typograﬁsche Fehler

verantwortlich gemacht werden und behält sich das

Recht vor, Änderungen an dem Produkt und den

Handbüchern ohne vorherige Ankündigung vorzu-

nehmen. Bird Home Automation GmbH übernimmt

keinerlei Garantie in Bezug auf das in diesem

Dokument enthaltene Material, einschließlich, aber

nicht beschränkt auf die implizierten Garantien der

Marktgängigkeit und Eignung für einen bestimmten

Zweck. Bird Home Automation GmbH haftet nicht

für Neben- oder Folgeschäden im Zusammenhang mit

der Bereitstellung, Durchführung oder Verwendung

dieses Materials. Das Gerät darf nur für den

vorgesehenen Zweck verwendet werden.

Gerätemodiﬁkationen

Dieses Gerät muss in Übereinstimmung mit den

Anweisungen in der Installationsanleitung installiert

und verwendet werden. Dieses Gerät enthält keine

vom Benutzer zu wartenden Komponenten. Durch

unbefugte Gerätemodiﬁkationen oder Änderungen

erlöschen alle anwendbaren Zertiﬁzierungen und

Zulassungen.

Verwendete Symbole

Achtung: Weist auf eine gefährliche Situation

hin, die, falls nicht verhindert, zum Tod oder

schweren Verletzungen führt.

Warnung: Weist auf eine gefährliche

Situation hin, welche, falls nicht verhindert,

zum Tod oder schweren Verletzungen

führen kann.

Vorsicht: Weist auf eine gefährliche

Situation hin, welche, falls nicht verhindert,

zu geringfügiger oder mäßiger Verletzung

führen kann.

NOTICE Bitte beachten: Weist auf eine gefährliche

Situation hin, welche, falls nicht verhindert,

zu Sachschäden führen kann.

Wichtig: Weist auf wichtige Informationen

hin, die den richtigen Betrieb des Produkts

gewährleisten.

Hinweis: Weist auf nützliche Informationen

hin, die die optimale Verwendung des Geräts

unterstützen.

• Einbau, Montage und Servicearbeiten elek-

trischer Geräte dürfen ausschließlich durch eine

Elektrofachkraft erfolgen. Bei Nichtbeachten

besteht die Gefahr schwerer gesundheitlicher

Schäden oder Lebensgefahr durch elektrische

Stromschläge.

• Geräte mit 110-240 V Anschluss: Das Gerät darf

nur an eine leicht zugängliche Netz-Steckdose

angeschlossen werden. Bei Gefahr ist der

Netzstecker zu ziehen.

• Benutzen Sie für die Stromversorgung des

Gerätes ausschließlich das mitgelieferte

Originalnetzteil, separat erhältliche

Hutschienennetzteile oder einen in dieser

Anleitung empfohlenen PoE-Switch/PoE-

Injektor.

• Durch elektrostatische Auﬂadung kann bei

direktem Kontakt mit der Leiterplatte das

Gerät zerstört werden. Vermeiden Sie daher ein

direktes Berühren der Leiterplatte zu jeder Zeit.

• Norm EN 60065 bzw. EN 60950 bzw. EN 62368

beachten.

• Verwenden Sie das Gerät nicht, wenn es

von außen erkennbare Schäden z. B. am

Gehäuse, an Bedienelementen oder an den

Anschlussbuchsen bzw. eine Funktionsstörung

aufweist. Im Zweifelsfall lassen Sie das Gerät von

einer autorisierten Fachkraft prüfen.

• Öffnen Sie das Gerät nicht. In solchen Fällen

erlischt jeder Gewährleistungsanspruch! Für

Folgeschäden übernehmen wir keine Haftung!

Das Gerät enthält keine durch den Anwender

zu wartenden Teile. Im Fehlerfall lassen Sie das

Gerät von einer autorisierten Fachkraft prüfen.

• Aus Sicherheits-, Zulassungs- und

Lizenzgründen (CE/FCC/IC etc.) ist das

eigenmächtige Umbauen und/oder Verändern

des Gerätes nicht gestattet.

• Das Gerät ist kein Spielzeug! Erlauben Sie

Säuglingen und Kindern nicht damit zu spielen.

• Um Erstickungsgefahr zu vermeiden, halten

Gefahrenhinweise

WARNUNG

Sie das Verpackungsmaterial von Säuglingen

und Kindern fern. Plastikfolien/-tüten,

Styroporteile etc. sind kein Spielzeug und

können gefährlich für Kinder sein. Entsorgen

Sie das Verpackungsmaterial sofort nach der

Entnahme des Produkts. Verwenden Sie das

Verpackungsmaterial nicht wieder.

• Verlegen Sie Kabel stets so, dass diese keine

Gefährdungen für Menschen und Haustiere

darstellen.

• An Teilen im Gerät liegt Spannung an.

Berühren Sie keine Teile, die nicht mit der

Installation, der Verdrahtung oder dem

Anschluss verbunden sind. Elektrische

Stromschläge können die Folge sein.

• Halten Sie die Geräte, die nicht als wetterfest

gekennzeichnet sind, von Wasser oder anderen

Flüssigkeiten fern.

• Führen Sie keine Installation durch und

stellen Sie keine Verbindungen her, während

die Stromversorgung eingeschaltet ist.

Beschädigungen am Gerät oder elektrische

Stromschläge können die Folge sein.

• Bevor Sie die Stromversorgung einschalten,

stellen Sie sicher, dass die Drähte nicht

gekreuzt oder kurzgeschlossen sind. Feuer

oder elektrische Stromschläge können die

Folge sein.

• Hochspannung kann intern vorhanden

sein. Öffnen Sie das Gerät nicht. Elektrische

Stromschläge können die Folge sein.

• Das Gerät ist nicht explosionsgeschützt. Nicht

in der Nähe von Gasen oder brennbaren

Materialien installieren oder verwenden. Feuer

oder Explosion können entstehen.

• Installieren Sie nicht zwei Stromversorgungen

parallel zu einem einzigen Eingang. Feuer oder

Beschädigung des Gerätes können entstehen.

Achten Sie darauf, nur ein einziges Netzteil an

das Gerät anzuschließen.

• Schließen Sie keinen Anschluss am Gerät

an eine Netzstromleitung an. Feuer oder

elektrische Stromschläge können die Folge

sein.

• Stellen Sie sicher, dass das Netzkabel nicht

beschädigt oder gequetscht ist. Wenn das

Netzkabel gebrochen ist, kann es zu einem

Brand oder elektrischen Stromschlag kommen.

• Nichts mit nassen Händen anstecken oder

abziehen. Elektrische Stromschläge können

die Folge sein.

• Führen Sie kein Metall oder brennbares

Material in das Gerät. Feuer, elektrische

Stromschläge oder Gerätestörungen können

die Folge sein.

• Bestehende Verdrahtungen wie Türgong-

verdrahtung usw. können Hochspannungs-

Wechselstrom enthalten. Schäden am Gerät

oder elektrische Stromschläge können

auftreten. Die Verdrahtung und Installation

muss von einem qualiﬁzierten Elektriker

durchgeführt werden.

• Gerätemontage an Wand oder Decke:

Vermeiden Sie Installationsorte, an denen das

Gerät Erschütterungen oder Stößen ausgesetzt

ist.

• Bei Geräten mit Erdungsklemmen muss eine

Erdung angeschlossen werden. Feuer oder

Gerätestörungen können die Folge sein.

• Bei Geräten mit Kunststoffglas oder Echtglas,

keinen hohen Druck auf das Glas ausüben. Bei

Bruch kann es zu Verletzungen kommen.

• Bei Geräten mit LCD, wenn LCD beschädigt

ist, nicht mit dem Flüssigkristall in Kontakt

kommen. Verletzungen können die Folge sein.

Wenn nötig, spülen Sie den Mund aus, reinigen

Sie Ihre Augen oder Haut mit klarem Wasser für

mindestens 15 Minuten und wenden Sie sich

an Ihren Arzt.

• Bringen Sie nichts auf dem Gerät an und

verdecken Sie das Gerät nicht mit einem Tuch,

Silikon, Klebstoff, Farbe, separater Abdeckung

etc. Es können Feuer- oder Gerätestörungen

auftreten.

• Installieren Sie das Gerät nicht an einer der

folgenden Orte. Feuer, Stromschlag oder

Gerätestörungen können die Folge sein.

 Orte unter direktem Sonnenlicht oder

Orte in der Nähe von Heizgeräten, die in

der Temperatur variieren.

 Orte mit Staub, Öl, Chemikalien,

Schwefelwasserstoff (heiße Quellen).

 Orte, die extremer Feuchtigkeit und Luft-

feuchtigkeit ausgesetzt sind, wie Bäder, Keller,

Gewächshäuser, etc.

 Orte, an denen die Temperatur extrem niedrig

ist, wie z. B. in einem gekühlten Bereich oder

vor einer Klimaanlage.

 Orte, die Dampf oder Rauch ausgesetzt sind

(z.B. in der Nähe von Heiz- oder Kochﬂächen).

 Orte, an denen Geräusch erzeugende Geräte

wie Dimmschalter oder Wechselrichter-

Elektrogeräte in unmittelbarer Nähe sind.

 Orte, die häuﬁgen Vibrationen oder Stößen

ausgesetzt sind.

• Bei Geräten mit Gegensprechfunktion ist darauf

zu achten, dass ein Anruftest durchgeführt wird,

bei dem beide Gegensprechgeräte auf geringer

Lautstärke eingestellt sind. Ein plötzlicher Anruf

etc. kann ankommen und das Gehör schädigen.

• Wenn das Gerät nicht ordnungsgemäß

funktioniert, ziehen Sie den Netzstecker aus der

Steckdose.

WARNUNG

DEUTSCH

Sicherheitsanweisungen

• Alle Geräte, die nicht als wetterfest

gekennzeichnet sind, sind nur für den

Innenbereich konzipiert und nicht im Freien

zu benutzen.

• Geräte, die als wetterfest gekennzeichnet

sind, nicht mit Hochdruckwasser besprühen.

Gerätestörungen können die Folge sein.

• Bei Sach- oder Personenschäden, die

durch unsachgemäße Hand habung oder

Nichtbeachten der Gefahrenhinweise

verursacht werden, übernehmen wir keine

Haftung. In solchen Fällen erlischt jeder

Gewährleistungsanspruch! Für Folgeschäden

übernehmen wir keine Haftung.

• Die Verwendung des Geräts muss unter

Beachtung der örtlich geltenden rechtlichen

Bestimmungen erfolgen.

• Lagern Sie das Gerät in einer trockenen und

belüfteten Umgebung.

• Achten Sie darauf, dass das Gerät weder

Stößen noch starkem Druck ausgesetzt ist.

• Installieren Sie das Gerät nicht an instabilen

Halterungen, Oberﬂächen oder Wänden.

Stellen Sie sicher, dass das Material stabil

genug ist, um das Gewicht des Geräts zu

tragen.

• Verwenden Sie bei der Installation des Geräts

ausschließlich passende Werkzeuge. Ein zu

großer Kraftaufwand mit Werkzeugen kann

das Gerät beschädigen.

• Verwenden Sie keine chemischen, ätzenden

oder aerosolhaltigen Reinigungsmittel.

• Verwenden Sie zum Reinigen ein sauberes,

trockenes Tuch.

• Verwenden Sie nur Zubehör, das den

technischen Daten des Geräts entspricht.

Dieses ist von Bird Home Automation GmbH

erhältlich.

• Verwenden Sie ausschließlich Ersatzteile die

von Bird Home Automation GmbH bereitge-

stellt oder empfohlen werden.

• Versuchen Sie nicht, das Gerät selbstständig

zu reparieren. Wenden Sie sich bezüglich

Reparatur und Wartung an Bird Home

Automation GmbH.

• Halten Sie das Gerät mehr als 1 m (3,3“)

entfernt von Mikrowelle, Radio, TV, WLAN

Router und anderen drahtlosen Geräten.

• Bei Geräten mit Gegensprechfunktion oder

eingebautem Lautsprecher oder eingebautem

Mikrofon oder Signalübertragungsfunktion,

NOTICE

installieren Sie die Drähte mehr als 30 cm

(12‘‘) entfernt von 100-240 V Wechselstromver-

drahtung. Ansonsten können Wechselstrom-

induzierte Geräusche und/oder Geräte-

Störungen auftreten.

• Installieren Sie das Gerät in einem Bereich, der

für zukünftige Inspektionen, Reparaturen und

Wartungen zugänglich ist.

• Wenn das Gerät in der Nähe eines

Mobiltelefons verwendet wird, kann das Gerät

gestört werden.

• Das Gerät kann beschädigt werden, wenn es

fallen gelassen wird. Mit Vorsicht behandeln.

• Das Gerät wird während eines Stromausfalls

außer Betrieb gesetzt.

• Bei Geräten mit Gegensprechfunktion oder

eingebautem Lautsprecher oder eingebautem

Mikrofon kann das Gerät in Bereichen, in denen

Antennen von Mobilfunksendern, Radio- oder

TV-Sendern in der Nähe sind, beeinträchtigt

werden.

• Bei Geräten mit LCD-Bildschirm muss im

Voraus darauf hingewiesen werden, dass

bei einem LCD-Panel, obwohl es mit sehr

hohen Präzisions techniken hergestellt wird,

unvermeidlich ein sehr kleiner Teil seiner

Bildelemente nicht immer beleuchtet oder

gar nicht beleuchten wird. Dies gilt nicht als

Gerätefehler.

• Bei Geräten mit Gegensprechfunktion können

Umgebungsgeräusche um das Gerät herum

eine reibungslose Kommunikation behindern.

Dies ist keine Fehlfunktion.

• Bei Geräten mit Benutzername/Passwort

ist der Anwender für den Zugriff mittels

Benutzername/Passwort auf das Gerät

verantwortlich. Vergewissern Sie sich ein

Passwort zu verwenden, das von einem

Dritten nicht leicht erraten werden kann. Wir

empfehlen Ihnen, das Passwort regelmäßig zu

ändern.

• Wir haften unter keinen Umständen für

Schäden, die aufgrund von Fehlern in der

Stromversorgung, Netzwerkgeräten oder

Endgeräten auftreten; Ausfälle aufgrund von

Internetanbietern und Mobilfunkanbietern;

Ausfälle aufgrund von getrennten oder

gestörten Leitungen und andere Übertragungs-

verluste, die es unmöglich machen, unseren

Dienst zu erbringen, sowie allen anderen

Ursachen die außerhalb unserer Verantwortung

liegen; Oder, wenn während der Übertragung

ein Fehler oder fehlende Daten auftreten.

Informationen zur Entsorgung elektrischer

und elektronischer Geräte (für

Privathaushalte)

Dieses Symbol auf Produkten oder begleitenden

Dokumenten weist darauf hin, dass elektrische oder

elektronische Geräte nicht with dem allgemeinen

Hausmüll entsorgt werden sollten. Bitte bringen Sie

solche Produkte zu den vorgesehenen Sammelstellen,

wo sie kostenfrei entgegengenommen und der

geeigneten Abfall- und Wiederverwertung zugeführt

werden. Alternativ dazu können Sie in einigen Ländern

die Produkte beim Kauf eines äquivalenten neuen

Produktes auch bei einem örtlichen Einzelhändler

zurückgeben. Die ordnungsgemäße Entsorgung dieses

Produkts trägt dazu bei, wertvolle Rohstoffe zu sparen

und möglichen negativen Auswirkungen auf die

Gesundheit und die Umwelt vorzubeugen, die durch

eine ungeeignete Abfallentsorgung entstehen können.

Bei den örtlichen Behörden erhalten Sie genauere

Informationen zu Ihrer nächsten zuständigen

Sammelstelle. Abhängig von der nationalen

Gesetzgebung können für die unvorschriftsmäßige

Entsorgung solcher Abfälle Strafen verhängt werden.

Informationen zur Entsorgung in Ländern außerhalb

der Europäischen Union

Dieses Symbol gilt nur in der Europäischen Union.

Wenn Sie dieses Produkt wegwerfen möchten,

kontaktieren Sie bitte die zuständigen Behörden

oder Händler in Ihrem Land, um sich über die

vorschriftsmäßige Entsorgung zu informieren.

Transport

NOTICE Bei Bedarf transportieren Sie das Gerät in

der Originalverpackung oder einer

entsprechenden Verpackung, so dass

Schäden vermieden werden.

Gewährleistung

Informationen zur Gewährleistung des Geräts ﬁnden

Sie unter www.doorbird.com/de/warranty

La page charge ...

DoorBird A1121 Series Manuel utilisateur

Marque: DoorBird

Modèle: A1121 Series

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DoorBird A1121 Series User manual
español: DoorBird A1121 Series Manual de usuario
Deutsch: DoorBird A1121 Series Benutzerhandbuch

DoorBird A1121 Series Manuel utilisateur

DoorBird A1121 Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents