DoorBird A1061X Manuel utilisateur

Marque: DoorBird

Modèle: A1061X

Catégorie: Haut-parleurs de la barre de son

Taper: Manuel utilisateur

VERSION ., MIN. HW .

Page 2-17

Installation Manual

IP Door Chime

A1061x Series

Seite 18-34

Installationsanleitung

IP Türgong

A1061x Serie

A1061X

Page 35-50

Manuel d‘installation

Carillon IP DoorBird

Série A1061x

INSTALLATION MANUAL

Read these instructions carefully before starting to use any components.

Keep the manual so you can refer to it at a later date if required. If you hand

over the device to other persons for use, please hand over the operating

manual as well.

To make things easier we use the term “device” for the product “DoorBird IP

Door Chime” and “mobile device” for a smartphone or tablet. You can always ﬁnd

the most up-to-date version of the installation manual on www.doorbird.com/

support

Liability

Every care has been taken in the preparation of this document.

Please inform Bird Home Automation GmbH of any inaccuracies or omissions.

Bird Home Automation GmbH cannot be held responsible for any technical

or typographical errors and reserves the right to make changes to the product

and manuals without prior notice. Bird Home Automation GmbH makes no

warranty of any kind with regard to the content of this document, including,

but not limited to, the implied warranties of merchantability and ﬁtness for

a particular purpose. Bird Home Automation GmbH shall neither be liable

nor responsible for incidental or consequential damages in connection with

the furnishing, performance or use of this material. This product is only to

be used for its intended purpose.

Equipment Modiﬁcations

This equipment must be installed and used in strict accordance with the

instructions given in the user documentation. This equipment contains no

components that require service by the user. Unauthorized equipment

changes or modiﬁcations will invalidate all applicable regulatory certiﬁcations

and approvals.

Symbols used

Caution: Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Danger: Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Warning: Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

ENGLISHENGLISH

Notice: Indicates a situation which, if not avoided, could result

in damage to property.

Note: Indicates useful information which helps in getting the

most out of the product.

NOTICE

Hazard information

• Mounting, installation and servicing work on electrical devices may

only be performed by a qualiﬁed eletrician. Failure to observe this

regulation could result in the risk of serious damage to health or fatal

injury due to electric shocks.

• Devices with 110-240 V connection: The device may only be connected

to an easily accessible power socket outlet. The mains adapter must

be pulled out if a hazard occurs.

• For power supply, only use the original plug-in mains adapter

delivered with the device or a recommended PoE-Switch/PoE-Injector

as speciﬁed in this manual.

• Because of electrostatic charging, direct contact with the circuit board

can result in destruction of the device. Direct contact with the circuit

board must therefore be avoided at any time.

• Observe the EN 60065 resp. EN 60950 resp. EN 62368 standard.

• Do not use the device if there are signs of damage to the housing,

control elements or connecting sockets, for example, or if it

demonstrates a malfunction. If you have any doubts, please have

the device checked by an authorized expert.

• Do not open the device. This voids the warranty of the device. The

device does not contain any parts that can be maintained by the

user. In the event of an error, please have the device checked by an

authorized expert.

• For safety, approval and licensing reasons (CE/FCC/IC etc.),

unauthorized change and/or modiﬁcation of the device is not

permitted.

• The device is not a toy; do not allow children to play with it. Do not

WARNING

Important: Indicates signiﬁcant information which is essential

for the product to function correctly.

leave packaging material lying around. Plastic ﬁlms/bags, pieces of

polystyrene, etc. can be dangerous in the hands of a child.

• Always lay cables in such a way that they do not become a risk to

people and domestic animals.

• Voltage is applied to parts within the equipment. Do not touch any

parts that are not associated with the installation, wiring, or connection.

Electric shock could result.

• On devices which are not marked as weather-proof: Keep the device

away from water or any other liquid.

• Do not install or make any wire terminations while power supply is

plugged in. It can cause eletric shock or damage to the device.

• Before turning on power, make sure wires are not crossed or shorted. If

not, ﬁre or eletric shock could result.

• High voltage may be present internally. Do not open the device.

Electric shock could result.

• The device is not of explosion-proof. Do not install or use near gases or

ﬂammable materials. Fire or explosion could result.

• Do not install two power supplies in parallel to a single input. Fire or

damage to the device could result. Be sure to connect a single power

supply to the device.

• Do not connect any terminal on the device to an AC power line. Fire or

electric shock could result.

• Keep AC cord from being marred or crushed. If the AC cord is fractured,

ﬁre or electric shock could result.

• Do not plug or unplug with wet hands. Electric shock could result.

• Do not put any metal or ﬂammable material into the device. Fire,

electric shock, or device trouble could result.

• Existing wiring may contain high voltage AC electricity. Damage to the

device or electric shock could result. Wiring and installation must be

done by a qualiﬁed eletrician.

• When mounting the device on a wall or ceiling, install the device in a

convenient location, but not where it could be jarred or bumped. Injury

could result.

• On devices with ground terminals, connect to an earth ground.

Otherwise ﬁre or malfunction could result.

• On devices with plastic or real glass, do not put high pressure on the

glass. If fractured, injury could result.

WARNING

ENGLISHENGLISH

• On devices with LCD, if LCD is punctured, do not allow contact with the

liquid crystal inside. Injury could result. If necessary, gargle your mouth

and clean your eyes or skin with clear water for at least 15 minutes and

consult your doctor.

• Do not put anything on the device or cover the device with cloth,

silicone, glue, coating, separate covering etc. Fire or device issues could

result.

• Do not install the device in any of the following locations. Fire, electric

shock, or device trouble could result.

 Places under direct sunlight or places near heating equipment that

varies in temperature.

 Places subject to dust, oil, chemicals, hydrogen sulﬁde (hot spring).

 Places subject to moisture and humidity extremes, such as bathrooms,

cellars, greenhouses, etc.

 Places where the temperature is very low, such as inside a refrigerated

area or in front of an air conditioner.

 Places subject to steam or smoke (e.g. near heating or cooking surfaces).

 Where noise generating devices such as dimmer switches or inverter

electrical appliances are closeby.

 Locations subject to frequent vibration or impact.

• On devices with intercom, be sure to perform a call test with low audio

volume on both intercom devices. A sudden call etc. may arrive causing

for example damage to your ear.

• If the device does not operate properly, unplug the power supply.

• All devices which are not marked as weather-proof are designed for

indoor use only. Do not use outdoor.

• On devices which are marked weather-proof: Do not spray with high-

pressure water. Device issues could result.

• We do not assume any liability for damage to property or personal injury

caused by improper use or the failure to observe the

• hazard information. In such cases, any claim under warranty ceases. For

consequential damages, we assume no liability!

Safety instructions

• The device shall be used in compliance with local laws and regulations.

• Store the device in a dry and ventilated environment.

• Avoid exposing the device to shocks or heavy pressure.

• Do not install the device on unstable brackets, surfaces or walls. Make

sure the material is strong enough to support the weight of the device.

• Use only applicable tools when installing the device. Using excessive

force with tools could cause damage to the device.

• Do not use chemicals, caustic agents, or aerosol cleaners.

• Use a clean dry cloth for cleaning.

• Use only accessories that comply with technical speciﬁcation of the

device. These can be provided by Bird Home Automation GmbH.

• Use only spare parts provided by or recommended by Bird Home

Automation GmbH.

• Do not attempt to repair the device by yourself. Contact Bird Home

Automation GmbH for service matters.

• Keep the device more than 1 m (3.3‘) away from microwave, radio, TV,

wireless router and any other wireless devices.

• On devices with intercom or built-in speaker or built-in microphone or

signal transmission functions, keep the wires more than 30 cm (12‘‘)

away from AC 100-240 V wiring. AC induced noise and/or device

malfunction could result.

• Install the device in an area that will be accessible for future inspections,

repairs and maintenance.

• If the device is used close to a cellular phone, the device may malfunction.

• The device can be damaged if dropped. Handle with care.

• The device turns inoperative during power failure.

• On devices with intercom or built-in speaker or built-in microphone,

in areas where cellular or Radio / TV broadcasting station antennas are

closeby, the device may be affected by radio frequency interference.

• On devices with LCD screen, it must be noted in advance that the LCD

panel, though manufactured with very high precision techniques,

inevitably will have a very small portion of its picture elements always lit

or not lit at all. This is not considered a device malfunction.

• On devices with intercom, due to the environmental sound around

NOTICE

ENGLISHENGLISH

the device, it may hinder smooth communication, but this is not a

malfunction.

• On devices with Username/Password, the Username/Password to

access the device is the customer‘s responsibility. Make sure to use

a password that cannot be easily guessed by a third party. We

recommend that you change the Password on a regular basis.

• We will, under no circumstances, be liable for damage that occurs due

to failures in power supply, network equipment or terminal devices;

failures due to Internet providers and cellular network providers;

failures such as disconnected lines and other losses in communication,

which makes it impossible to provide this service as well as in any way

delay this service due to any other causes outside of our responsibility;

or if an error or missing data occurs during transmission.

Warranty Information

For information about the device warranty, see www.doorbird.com/warranty

Transportation

When transporting the device, use the original packaging or equiva-

lent to prevent damage to the device.

NOTICE

Information on disposal for users of waste electrical & electronic

equipment (private household)

This symbol on the products and/or accompanying documents means that

used electrical and electronic products should not be mixed with general

household waste. For proper treatment, recovery and recycling, please take

these products to designated collection points, where they will be accepted

an a free of charge basis. Alternatively, in some countries you may be able to

return your products to your local retailer upon the purchase of an equivalent

new product. Disposing of this product correctly will help to save valuable

resources and prevent any potential negative effects on human health and

the environment which could otherwise arise from inappropriate waste

handling. Please contact your local authority for further details of your nearest

designated collection point. Penalties may be applicable for incorrect disposal

of this waste, in accordance with national legislation.

Device

COMPONENTS

Contents

 1x Device

 1x Power supply unit

(mains adaptor) with four

country-speciﬁc adaptors

 1x RJ45 network cable (300 cm)

 3x Phillips countersunk

head screws

Loudspeaker

Large-sized broadband speaker.

Cable inlet

To feed the cable into the device, if the

cables are surface-mounted.

Diagnostic-LED

To visualize the current status of the device.

Front

 3x Dowels

 3x Crimp connectors

 1x Installation manual

 1x Drilling template

 1x Quickstart Guide with Digital

Passport

Information on disposal in other countries outside the European Union

This symbol is only valid in the European Union. If you wish to discard this

product, please contact your local authorities or dealer and ask for the correct

method of disposal.

ENGLISHENGLISH

VIDEOS

Need help with the installation? Be sure to watch our installation videos

which can be found on http://www.doorbird.com/support

Each individual step of the installation is clearly documented in the videos.

Mounting points

To mount the device on a wall or ceiling

using countersunk head screws.

Connection terminal

Power supply (15 V DC -; 15 V DC +),

Storey-call button (STC),

Setup button (SET), LAN/PoE.

Cable clamp

Back

INSTALLATION

All steps below should be carried out carefully by a competent adult, taking

into consideration any applicable safety regulations. Should you have any

questions, please contact us or a competent specialist directly. Please ensure

that all wires used for the installation are undamaged along their entire

length and approved for this type of use.

Network speed and network components

Please ensure that the upload speed of your Internet connection is at least

0.5 Mbps. You can also carry out a speed test at any time via the DoorBird App.

The user experience is only as good as your network speed, network stability

and quality of your network components, such as your Internet router and

WiFi access points or WiFi repeaters. Please also make sure that your network

components are no more than two years old, have been manufactured by a

well-known manufacturer, and have the latest firmware installed.

Should these requirements not be fulfilled, it may happen, i.e. that the

performance of audio and video is poor or push notifications are delayed or

do not arrive on your smartphone or tablet at all.

High-speed Internet (via landline): DSL, cable or optical fibre

Network: 802.11b/g/n 2.4 GHz or Ethernet, with DHCP

1010

STEP : SWITCHING OFF POWER

Switch off the power to all wires leading to the assembly location, i.e.

the door chime, electric door opener, power supply unit, PoE-Switch/

PoE-Injector etc.

STEP : DISMANTLING THE EXISTING DOOR CHIME

Should there already be a door chime on the wall, please do not hesitate to

remove it.

STEP : DETERMINING THE ASSEMBLY LOCATION

The device is designed for indoor-use only.

Press the drilling template of the device against the wall or ceiling at the

desired installation site and mark the boreholes with a pencil. Remove the

drilling template again. Ensure that no cables are to be found in the wall or

ceiling behind the boreholes.

STEP : DOWELS AND SCREWS

If the wall of the house is not made of wood, you should drill dowel holes 5 mm

in diameter in the wall according to the drilling template and then place

the dowels provided into the boreholes.

If you must drill holes in a wall, insert screws into a wall or lever up a

wall, ensure that no cables or mains (gas, water, etc.) are to be found

in the wall.

If the wall of the house is made of wood, dowels are not normally required.

There are special dowels for assembling the device on an insulating wall, e.g.

Fischer insulating dowels.

Please check with your insulating material manufacturer regarding which

dowels they recommend. Use the Phillips countersunk head screws provided

to position it in the dowels or on the wall, so that the countersunk head

screws protrude a few millimeters above the wall.

STEP : PREPARING THE POWER SUPPLY

The device can be powered by two simple doorbell wires using the power-

supply unit (mains adaptor) supplied with it or via PoE (Power over Ethernet)

using a network cable. The device can alternatively also be supplied with a

DIN-rail power supply unit that you can obtain from us directly. The device

does not use battery power.

1111

ENGLISHENGLISH

Option 1: Power supply using the power-supply unit (mains adaptor)

Two insulated wires are required to power the device by connecting it to the

power-supply unit (mains adaptor) supplied with it. These wires are normally

already there and are freely accessible once you have removed the previous

door chime. You can also connect the power supply without any additional

wires to the door chime, the power supply has a 300cm long cable with two

insulated wires. If you need longer wiring, connect the wires of the power

supply using the supplied crimp connectors with the two wires that you want

to use for the power supply.

Do not plug the power supply unit into the wall socket yet.

Only use the power supply unit provided along with the device, or a

DIN-rail power supply unit that you can obtain from us separately,

since this has been specially stabilized electrically and is equipped

with an integrated audio interference reduction device. Other power

supply units may destroy the device or cause poor transmission quality.

The warranty automatically expires if you use a different power supply

unit. The power supply unit is plugged into a wall socket inside your

house, usually where the two wires from your previous door chime

comes out of the wall in the interior of the house.

Option 2: Power supply via PoE (as an alternative)

To power the device via a PoE-Switch (e.g. D-Link DGS-1008P) or PoE-Injector

(e.g. DoorBird Gigabit PoE Injector) in accordance with the PoE standard IEEE

802.3af Mode A, the four wires bearing the numbers 1, 2, 3 and 6 of a Cat.5

cable or better are to be used. A Cat.5 cable or better must be used as network

signals can only be transmitted over completely insulated, shielded and

twisted cables. If you use PoE as a source of power, the WiFi interface of the

device is automatically inactive, and the four wires for PoE then simultaneously

form the data link. The device won’t start if your PoE Switch or PoE injector

does not support the PoE Standard IEEE 802.3af Mode A (see Diagnostic-LED

and Diagnostic-Sounds).

1. Disconnect the PoE-Switch or PoE-Injector from the power grid.

2. Place the network cable in the installation site of the device.

Do not combine the power supply from the power supply unit

(mains adaptor) with the power supply via PoE. You can find further

information about PoE here: http://www.doorbird.com/poe

STEP : FURTHER CONNECTIONS (OPTIONAL)

If desired, connect additional wires to the installation site of the device.

The wires or connection options mentioned in this section are optional.

NOTICE

1212

Be sure to use

four insulated,

shielded and

twisted wires of

a network cable

in accordance

with the Cat.5

standard or

better. Only four

wires of the

network cable

will be used.

Connecting the unit to a network

You can connect the device to your existing network

via WiFi, or alternatively use a network cable (Ethernet).

For reasons of network stability, we principally recom-

mend using a network cable, as WiFi is sensitive to

interference (range, house walls acting as shields, relia-

bility of performance, third party WiFi networks, wireless

transmitters causing interference in the area, etc.).

The device can be powered by PoE or using the power

supply unit provided. If you use PoE as a source of power,

the WiFi interface of the device remains inactive.

Use only a network cable with RJ45 plug that meets the

Cat.5 standard or a better one.

Connect the network cable to your PoE-Switch or

PoE-Injector that is connected to your Internet router.

Then connect it to the device.

Conventional Storey-call button

You can connect a conventional button to the device

to realize a separate storey-call. A Storey-call button is

typically used if you have more than one door, e.g. street

door and apartment door. Please make sure to add no

voltage on that contact.

Please make sure to add no voltage on these ports. Extra voltage

may destroy the device immediately.

STEP : PREPARING THE WIRES

Remove about 5 mm of insulation material at the end of the wires that you

would like to connect to the device (Power supply, Storey-call button).

STEP : CONNECTING THE WIRES

It is possible to connect the cables and wires to the device conveniently and

safely via a connection terminal on the reverse of the device. The individual

contacts on the connection terminal are labelled on the casing. You can

connect all necessary cables and wires to the device using the connection

terminal now. Please remove any cables and wires on the connection

terminal that you do not need. Remove about 5 mm of insulation material at

the end of the wires that you would like to connect to the screw connection

terminal of the device.

Two insulated

wires.

6 (R-)

3 (R+)

2 (T-)

1 (T+)

NOTICE

1313

ENGLISHENGLISH

Please take care when connecting the cables and wires. Connecting

the cables and wires the wrong way may destroy the device.

STEP : FINAL ASSEMBLY

Mount the device on the Phillips countersunk head screws you already

positioned in step 3 and 4.

STC LAN/POEVDC

CONNECTOR DESCRIPTION

15 V DC -

15 V DC Power supply, negative pole (-)

Do not power the device simultaneously via the

power supply from the power supply unit (mains

adaptor) and the power supply via PoE.

15 V DC +

15 V DC Power supply, positive pole (+)

Do not power the device simultaneously via the

power supply from the power supply unit (mains

adaptor) and the power supply via PoE.

STC Storey-call button, 0 V DC/V AC, 0 A

LAN/POE

Ethernet Network cable with RJ45 plug, supports PoE

Do not power the device simultaneously via the

power supply from the power supply unit (mains

adaptor) and the power supply via PoE.

V+V-

NOTICE

1414

STEP : ACTIVATING THE DEVICE

Switch on the power leading to the assembly location again. If you use PoE,

make sure to switch on power of the PoE-Switch or PoE-Injector you have

connected the device to.

Do not power the device simultaneously via the power supply

from the power supply unit (mains adaptor) and the power

supply via PoE.

You can see if the device is powered by checking the Diagnostic-LED, which

lights up after about 30 to 60 seconds after the power is connected. The

device is ready for operation (booting up process, any software updates, etc.)

once it has emitted a short diagnosis sound from the integrated loudspeaker.

This may last for up to 5 minutes. Should you not hear a sound, please check

the power supply. Please also check whether you have used a wall-plug pow-

er supply and not PoE and whether you have connected the positive pole and

negative pole to the device correctly.

STEP : DOWNLOADING AND INSTALLING THE APP

Download the “DoorBird” App by Bird Home Automation onto your mobile

device from the Apple App Store or Google Play Store. You can always find

the most up-to-date version of the App manual on www.doorbird.com/support.

If you use WiFi for connecting the device to your Internet router, first go to

the DoorBird App “Settings → WiFi Setup” and follow the instructions.

If you have finished the WiFi setup or have connected the device to your

Internet router by means of a network cable, go to the DoorBird App

“Settings → Administration” and login to the video door station you would

like to pair the device with. To add the device there, go to “Peripherals →

Settings → Add”.

If you have problems adding the device to the App please check if the device

is online ( www.doorbird.com/checkonline ). If the device is not online, please

check the WiFi or network cable connection again.

DIAGNOSTIC-LED

You can see if the device is powered by checking the Diagnostic-LED,

which lights up after about 30 to 60 seconds after the power is connected.

The Diagnostic-LED automatically turns off after about 5 minutes.

DIAGNOSTIC-SOUNDS

After around one to five minutes, the device emits brief diagnostic sounds

after it has been connected to the power grid.

NOTICE

1515

ENGLISHENGLISH

TECHNICAL SPECIFICATIONS

Dimensions:

125 x 119 x 26 mm (H x W x D)

4,92 x 4,68 x 1,02 in (H x W x D)

Power Supply:

15 V DC or Power over Ethernet

(PoE 802.3af Mode-A)

Operating conditions:

0 to +55°C / 32 to 131°F

Relative Humidity

10% to 85% (non condensing)

Connectors:

1 x RJ45, 4 x Screw terminal

Loudspeaker:

102 dB

WiFi:

2.4 GHz, 802.11 b/g/n, internal

antenna

PoE:

IEEE 802.3 af/at

Housing:

Polycarbonate, UV-resistant

System requirements:

Mobile Device: Newest iOS on

iPhone/iPad, newest Android on

Smartphone/Tablet

Internet: High-Speed Landline

Broadband Internet connection, DSL,

cable or ﬁber optic, no socks or proxy

server

Network: 802.11b/g/n 2.4 GHz

or Ethernet Network, with DHCP

Compatible with all DoorBird IP

Video Door Stations.

Scope of delivery:

1 x IP Door Chime

1 x Network Cable

1 x Power supply unit (mains

adaptor) with four country-speciﬁc

adaptors (110 - 240 V AC to 15 V DC)

1 x Small parts

1 x Installation manual

Approvals:

CE, IC, FCC, RoHS, IP50

Weight:

200 g

Errors and omissions excepted.

1616

LEGAL NOTES

General remarks

1. DoorBird is a registered trademark of Bird

Home Automation GmbH.

2. Apple, the Apple logo, Mac, Mac OS,

Macintosh, iPad, Multi-Touch, iOS, iPhone

and iPod touch are trademarks of Apple Inc.

3. Google, Android and Google Play are

trademarks of Google, Inc.

4. The Bluetooth® word mark and logos are

registered trademarks of Bluetooth SIG, Inc.

5. All other company and product names may

be trademarks of the respective companies

with which they are associated.

6. We reserve the right to make changes to

our products in the interests of technical

advancement. The products shown may also

look different from the products supplied

based on ongoing enhancement.

7. Reproducing or using texts, illustrations and

photos from this instruction manual in any

media – even if only in the form of excerpts

– shall only be permitted with our express

written consent.

8. The design of this manual is subject to

any liability for any errors or any erroneous

content or printing errors (even in the case

of technical specifications or within graphics

and technical sketches).

9. Our products are in compliance with

all technical guidelines, electrical and

telecommunications regulations applicable

in Germany, the EU and the USA.

10. Our products and also the components

contained therein (ICs, software, etc.)

may only be used for civilian non-military

purposes.

Data privacy and data security

1. For maximum security, the device uses the

same encryption technologies as are used

in online banking. For your security, no port

forwarding or DynDNS is used either.

2. The data centre location for remote access

over the Internet by means of an App is

obligatory in the EU if the determined

Internet IP-Address location of the device is

within the EU. The data centre is operated

in line with the most stringent security

standards.

3. Video, audio and any other surveillance

methods can be regulated by laws that vary

from country to country. Check the laws in

your local region before installing and using

this device for surveillance purposes.

If the device is a door-, indoor station or camera:

• In many countries video and voice signal may

only be transmitted once a visitor has rung the

bell (data privacy, configurable in the App).

• Please carry out the mounting in such a

way that the detection range of the camera

limits the device exclusively to the immediate

entrance area.

• The device may come with a visitor history and

motion sensor. You can activate/deactivate

this function if required.

If necessary, indicate the presence of the device

in a suitable place and in a suitable form.

Please observe any relevant country-specific

statutory regulations concerning the use of

surveillance components and surveillance

cameras applicable at the installation site.

Check with the property owner and your house

community if you are allowed to install and use

this product. Bird Home Automation GmbH

cannot be held responsible for any miss-use or

miss-configuration of this product, including

the unauthorized opening of a door.

Bird Home Automation cannot be held

responsible for damages caused by improper

existing installations or improper installation.

Software and operating system’s updates

(so-called “firmware updates”) are generally

automatically installed on the products of

Bird Home Automation GmbH via Internet,

if technically possible. Automatic firmware

updates keep the products‘ software up to

date so that they always work reliably, safely

and efficiently. Through further development,

features can be added, extended or slightly

changed. Major changes or limitations to

existing features will generally occur if Bird

Home Automation GmbH deems it necessary

(e.g. for data protection, data security or

stability reasons, or to keep them up to date).

When a firmware update is available, Bird

Home Automation GmbH‘s servers generally

automatically distribute it to all compatible

products connected to the Internet or Bird

Home Automation GmbH‘s servers. This process

is gradual and can take several weeks. As soon

as a product receives a firmware update, the

system will be installed and will restart by itself.

Installed firmware updates cannot be undone.

Since the products and software of Bird Home

Automation GmbH are not explicitly customer-

specific products, a customer cannot deny an

automatic update if the product is connected

to the Internet or to the Bird Home Automation

GmbH’s server.

1717

ENGLISHENGLISH

Publisher

Bird Home Automation GmbH

Uhlandstraße 165

10719 Berlin

Germany

Web: www.doorbird.com

Email: [email protected]

It is possible that these manual still contains

typographical errors or printing errors.The

information in this manual will be checked

regularly and corrections will be made in the

next version. We accept no liability for errors

of a technical or printing nature and their

consequences.

INSTALLATIONSANLEITUNG

Lesen Sie diese Anleitung sorgfältig, bevor Sie die Komponenten in Betrieb

nehmen. Bewahren Sie die Anleitung zum späteren Nachschlagen auf!

Wenn Sie das Gerät anderen Personen zur Nutzung überlassen, übergeben

Sie auch diese Bedienungsanleitung.

Die stets aktuelle Version der Installationsanleitung ﬁnden Sie unter

www.doorbird.com/de/support

Zur Vereinfachung der Begriffe verwenden wir „Gerät“ für das Produkt

„IP Türgong“ sowie „mobiles Endgerät“ für ein Smartphone/Tablet.

Haftung

Die Erstellung dieses Dokuments wurde sorgfältig vorbereitet. Bitte infor-

mieren Sie Bird Home Automation GmbH über etwaige Ungenauigkeiten

oder Unterlassungen. Bird Home Automation GmbH kann nicht für tech-

nische oder typografische Fehler verantwortlich gemacht werden und behält

sich das Recht vor, Änderungen an dem Produkt und den Handbüchern

ohne vorherige Ankündigung vorzunehmen. Bird Home Automation GmbH

übernimmt keinerlei Garantie in Bezug auf das in diesem Dokument ent-

haltene Material, einschließlich, aber nicht beschränkt auf die implizierten

Garantien der Marktgängigkeit und Eignung für einen bestimmten Zweck.

Bird Home Automation GmbH haftet nicht für Neben- oder Folgeschäden im

Zusammenhang mit der Bereitstellung, Durchführung oder Verwendung dieses

Materials. Das Gerät darf nur für den vorgesehenen Zweck verwendet werden.

Gerätemodifikationen

Dieses Gerät muss in Übereinstimmung mit den Anweisungen in der

Installationsanleitung installiert und verwendet werden. Dieses Gerät ent-

hält keine vom Benutzer zu wartenden Komponenten. Durch unbefugte

Gerätemodifikationen oder Änderungen erlöschen alle anwendbaren

Zertifizierungen und Zulassungen.

Verwendete Symbole

Achtung: Weist auf eine gefährliche Situation hin, die, falls

nicht verhindert, zum Tod oder schweren Verletzungen führt.

Warnung: Weist auf eine gefährliche Situation hin, welche,

falls nicht verhindert, zum Tod oder schweren Verletzungen

führen kann.

DEUTSCH

Bitte beachten: Weist auf eine gefährliche Situation hin,

welche, falls nicht verhindert, zu Sachschäden führen kann.

Hinweis: Weist auf nützliche Informationen hin, die die optimale

Verwendung des Geräts unterstützen.

NOTICE

Wichtig: Weist auf wichtige Informationen hin, die den richtigen

Betrieb des Produkts gewährleisten.

Vorsicht: Weist auf eine gefährliche Situation hin, welche, falls

nicht verhindert, zu geringfügiger oder mäßiger Verletzung

führen kann.

Gefahrenhinweise

• Einbau, Montage und Servicearbeiten elek trischer Geräte dürfen

ausschließlich durch eine Elektrofachkraft erfolgen. Bei Nichtbeachten

besteht die Gefahr schwerer gesundheitlicher Schäden oder

Lebensgefahr durch elektrische Stromschläge.

• Geräte mit 110-240 V Anschluss: Das Gerät darf nur an eine leicht

zugängliche Netz-Steckdose angeschlossen werden. Bei Gefahr ist der

Netzstecker zu ziehen.

• Benutzen Sie für die Stromversorgung des Gerätes ausschließlich

das mitgelieferte Originalnetzteil oder einen in dieser Anleitung

empfohlenen PoE-Switch/PoE-Injektor (sofern das Gerät PoE

unterstützt).

• Durch elektrostatische Auﬂadung kann bei direktem Kontakt mit

der Leiterplatte das Gerät zerstört werden. Vermeiden Sie daher ein

direktes Berühren der Leiterplatte zu jeder Zeit.

• Norm EN 60065 bzw. EN 60950 bzw. EN 62368 beachten.

• Verwenden Sie das Gerät nicht, wenn es von außen erkennbare

Schäden z. B. am Gehäuse, an Bedienelementen oder an den

Anschlussbuchsen bzw. eine Funktionsstörung aufweist. Im Zweifelsfall

lassen Sie das Gerät von einer autorisierten Fachkraft prüfen.

• Öffnen Sie das Gerät nicht. In solchen Fällen erlischt jeder

Gewährleistungsanspruch! Für Folgeschäden übernehmen wir keine

Haftung! Das Gerät enthält keine durch den Anwender zu wartenden

WARNUNG

Teile. Im Fehlerfall lassen Sie das Gerät von einer autorisierten Fachkraft

prüfen.

• Aus Sicherheits-, Zulassungs- und Lizenzgründen (CE/FCC/IC etc.) ist

das eigenmächtige Umbauen und/oder Verändern des Gerätes nicht

gestattet.

• Das Gerät ist kein Spielzeug! Erlauben Sie Kindern nicht damit zu

spielen. Lassen Sie das Verpackungsmaterial nicht achtlos liegen.

Plastikfolien/-tüten, Styroporteile etc. können für Kinder zu einem

gefährlichen Spielzeug werden.

• Verlegen Sie Kabel stets so, dass diese keine Gefährdungen für

Menschen und Haustiere darstellen.

• An Teilen im Gerät liegt Spannung an. Berühren Sie keine Teile, die

nicht mit der Installation, der Verdrahtung oder dem Anschluss

verbunden sind. Elektrische Stromschläge können die Folge sein.

• Halten Sie die Geräte von Wasser oder anderen Flüssigkeiten fern, die

nicht als wetterfest gekennzeichnet sind.

• Führen Sie keine Installation durch und stellen Sie keine Verbindungen

her, während die Stromversorgung eingeschaltet ist. Beschädigungen

am Gerät oder elektrische Stromschläge können die Folge sein.

• Bevor Sie die Stromversorgung einschalten, stellen Sie sicher, dass

die Drähte nicht gekreuzt oder kurzgeschlossen sind. Feuer oder

elektrische Stromschläge können die Folge sein.

• Hochspannung kann intern vorhanden sein. Öffnen Sie das Gerät nicht.

Elektrische Stromschläge können die Folge sein.

• Das Gerät ist nicht explosionsgeschützt. Nicht in der Nähe von Gasen

oder brennbaren Materialien installieren oder verwenden. Feuer oder

Explosion können entstehen.

• Installieren Sie nicht zwei Stromversorgungen parallel zu einem

einzigen Eingang. Feuer oder Beschädigung des Gerätes können

entstehen. Achten Sie darauf, nur ein einziges Netzteil an das Gerät

anzuschließen.

• Schließen Sie keinen Anschluss am Gerät an eine Netzstromleitung an.

Feuer oder elektrische Stromschläge können die Folge sein.

• Stellen Sie sicher, dass das Netzkabel nicht beschädigt oder

gequetscht ist. Wenn das Netzkabel gebrochen ist, kann es zu einem

Brand oder elektrischen Stromschlag kommen.

• Nichts mit nassen Händen anstecken oder abziehen. Elektrische

Stromschläge können die Folge sein.

WARNUNG

La page charge ...

DoorBird A1061X Manuel utilisateur

Marque: DoorBird

Modèle: A1061X

Catégorie: Haut-parleurs de la barre de son

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DoorBird A1061X User manual
Deutsch: DoorBird A1061X Benutzerhandbuch

DoorBird A1061X Manuel utilisateur

DoorBird A1061X Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents