Blackstone 6038 36 Inch Griddle Drop-In Le manuel du propriétaire

BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

SAFETY ALERT KEY

 DANGER

Indicates a hazardous situation

that, if not avoided, will result in

death or serious injury.

 CAUTION

Indicates a hazardous situation

that, if not avoided, could result

in minor or moderate injury.

 WARNING

Indicates a hazardous situation

that, if not avoided, could result

in death or serious injury.

NOTICE

Indicates information considered

important, but not hazard-

related (e.g. messages related to

property damage).

OWNER’S MANUAL

IMPORTANT:

This instruction manual contains important

information necessary for the proper assembly and safe

use of the appliance.

Read and follow all warnings and instructions before

assembling and using the appliance.

Follow all warnings and instructions when using

the appliance.

Keep this manual for future reference.

Installer/Assembler: Leave these instructions with the consumer.

For the latest version of this manual,

scan this code or visit

BlackstoneProducts.com/support

| CONTACT CUSTOMER SUPPORT BEFORE RETURNING APPLIANCE TO RETAILER.

MODEL: v06

36" GRIDDLE

DROP-IN WITH HOOD AND INSULATING JACKET

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . .

ACTIVATE YOUR WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

ASSEMBLY GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

USING YOUR BLACKSTONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | IMPORTANT SAFETY INFORMATION

GAS APPLIANCE SAFETY

• The use of alcohol, prescription, or non-prescription drugs may

impair the consumer’s ability to properly assemble or safely

operate the appliance.

• Keep children and pets away from the appliance at all times.

• Have a type BC or ABC fire extinguisher readily available.

DO NOT USE FOR PURPOSES OTHER THAN INTENDED:

• DO NOT use for commercial cooking.

• DO NOT use this appliance as a heater.

 WARNING

Improper installation, use, adjustment, alteration, service,

modification, or maintenance can cause injury or property

damage. Refer to this manual.

INSTALLATION MUST CONFORM WITH LOCAL CODES

In the absence of local codes, installation must conform with

either ANSI Z223.1/NFPA 54, CSA B149.1, or CSA B149.2.

 WARNING

• DO NOT store or use gasoline or other flammable liquids

or vapors in the vicinity of this or any other appliance.

• An LPG cylinder not connected for use shall not be

stored in the vicinity of this or any other appliance.

 DANGER

• NEVER operate this appliance unattended.

• If a fire should occur, keep away from the appliance and

immediately call your fire department. DO NOT attempt

to extinguish an oil or a grease fire with water.

Failure to follow these instructions could result in fire or

property damage, personal injury or death.

 DANGER

If you smell gas:

• Shut o gas to the appliance.

• Extinguish any open flame.

• Open hood.

• If odor continues, keep away from the appliance

and immediately call your gas supplier or your fire

department.

Failure to follow these instructions could result in fire or

property damage, personal injury or death.

ELECTRIC APPLIANCE SAFETY

TO PROTECT AGAINST ELECTRIC SHOCK:

• DO NOT immerse cord or plugs in water or other liquid.

• Unplug from the outlet when not in use and before cleaning. Allow

to cool before putting on or taking o parts.

• DO NOT use an outdoor cooking gas appliance for purposes other

than intended.

• DO NOT operate this appliance with a damaged cord, plug, or after

the appliance malfunctions or has been damaged in any manner.

Contact the manufacturer for repair.

• DO NOT let the cord hang over the edge of a table or touch

hot surfaces.

• Keep any electrical supply cord and the fuel supply hose away from

heated surfaces.

• When connecting, first connect plug to the appliance then into

the outlet.

USE ONLY A GROUND FAULT INTERRUPTER (GFI) PROTECTED CIRCUIT

WITH THIS APPLIANCE.

• This appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with

NFPA 70 Canadian Electrical Code, Part I.

• DO NOT remove the grounding plug or use with an adapter

of 2 prongs.

• Use only extension cords with a 3 prong grounding plug, rated for

the power of the equipment, and approved for outdoor use with a

W-A marking.

MODEL: 

IMPORTANT SAFETY INFORMATION



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALACTIVATE YOUR WARRANTY

Register your appliance at

BlackstoneProducts.com/register

The North Atlantic Imports LLC 1-Year Warranty covers replacement

parts up to one year after the date of purchase.

TO ENABLE THIS WARRANTY, YOU WILL NEED TO PROVIDE:

☞

☞ Your appliance’s Serial Number

The Serial Number can be found on your appliance’s

Manufacturer Label.

(The Manufacturer Label is a large silver sticker found on the body of your

appliance.)

WARRANTY OVERVIEW

North Atlantic Imports, the manufacturer, will warranty for one year

from purchase all parts, workmanship, and finishes. It will be the

manufacturer’s option as to whether to repair or replace any of the

above items. All warranties are limited to the original purchaser

only. This warranty does not cover any liability on the part of North

Atlantic Imports, its agents or employees, for any indirect or conse-

quential damages for breach of warranty. The purchaser must follow

the manufacturer’s usage instructions.

Under no circumstances is the manufacturer responsible for

damages from the failure to operate the cooking station properly. It is

the responsibility of the purchaser to establish the warranty period

by verifying the original purchase date with original sales receipt.

DETAILED ExPLANATION OF THE WARRANTY

North Atlantic Imports LLC warrants to the owner that the product

covered by this agreement is free from defects in material and work-

manship under normal use and service for which it was intended if,

but only if, it has been operated in accordance with North Atlantic

Imports LLC instructions exclusively for domestic use, and not for

private or public club, institutional or commercial purposes.

North Atlantic Imports LLC’s obligation under this warranty is limited

to replacing or repairing, free of charge, any part or parts that

may prove, to the satisfaction of North Atlantic Imports LLC, to be

defective under normal home use and service within the following

stated periods of time from the date of purchase; for one year from

purchase, all parts, finish, and workmanship. Should any failure

to conform to this warranty become apparent during applicable

warranty periods stated above, the original purchaser must notify

North Atlantic Imports LLC of breach of warranty within the appli-

cable warranty period.

North Atlantic Imports LLC shall upon notice and compliance by the

original purchaser with such instructions, correct such nonconfor-

mity by repair or replacement of the defective part or parts.

Correction in the manner provided above shall constitute a fulfill-

ment of all obligations of North Atlantic Imports LLC with respect to

the quality of the product.

North Atlantic Imports LLC does not warrant this equipment to meet

the requirement of any safety code of any state, municipality or other

jurisdiction, and the original purchaser assumes all risk and liability

whatsoever resulting from the use thereof, whether used in accor-

dance with North Atlantic Imports LLC instructions or otherwise.

This warranty does not cover and is intended to exclude any liability

on the part of North Atlantic its agents, servants or employees

whether under this warranty or implied by law for any indirect or

consequential damages for breach on any warranty. The purchaser

must establish all applicable warranty periods pursuant to this

warranty by verifying the original purchase date by producing the

dated sales receipt. This warranty shall not apply to this product or

any other part thereof which has been subject to accident, negli-

gence, alteration, abuse, or misuse or which has been repaired or

altered without North Atlantic written consent, outside of North

Atlantic Imports LLC factory. The full manufacturer warranty is

not valid for griddles purchased from unlicensed, third-party

resellers, purchased at a discount due to missing or damaged

parts, or purchased as a floor model; at the discretion of North

Atlantic Imports.

North Atlantic Imports LLC makes no warranty whatsoever in respect

to accessories or parts not supplied with it. This warranty shall

apply only within the boundaries of the United States of America and

Canada. This warranty gives the original purchaser specific rights,

and the original purchaser may also have other rights, which vary

from state to state.

��

☞

FREE

MOBILEFRIENDLY

COOKBOOK

when you register



MODEL: 

ACTIVATE YOUR WARRANTY



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | ASSEMBLY GUIDE MODEL: 

ASSEMBLY GUIDE

ExPLODED VIEW

6

1

13

7

19

4

16

10

2

14

8

5

17

11

3

15

9

18

12



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALASSEMBLY GUIDEMODEL: 

1 Griddle body (1 piece) 2 Griddle top (1 piece) 3 Hood handle (1 piece)

4 Jacket base outer panel (1 piece) 5 Jacket base inner panel (1 piece) 6 Jacket rear inner

panel (1 piece)

7 Jacket rear outer

panel (1 piece)

8 Jacket left inner

panel (1 piece)

9 Jacket left outer

panel (1 piece)

10 Jacket right

inner panel (1 piece)

11 Jacket right

outer panel (1 piece)

12 Jacket silicone

sleeve (1 piece)

13 Hat channels

(2 pieces)

14 Mica washers

(2 pieces)

15 Grease cup

(1 piece)

16 Control knobs

(4 pieces)

17 Feet (4 pieces) 18 PCB box

(1 piece)

19 Match holder

(1 piece)

20 Hardware pack (1 piece)

a. M6 shoulder bolts (4 pieces)

b. M6x15 screws (6 pieces)

c. M6x35 screws (4 pieces)

d. M6x45 screws (4 pieces)

PARTS LIST

[a.]

[b.]

[c.]

[d.]



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | ASSEMBLY GUIDE

ASSEMBLY INSTRUCTIONS

Find a large, clean area to assemble your appliance.

Remove all packing material before assembling.

 CAUTION

Sharp edges. Wear gloves while assembling.

NOT INCLUDED (OPTIONAL):

Two (2) D batteries

ELECTRIC REQUIREMENTS:

120V 60Hz

 CAUTION

Heavy pieces. Two people should assemble this appliance.

NOTICE

Place appliance on a heat-resistant and flame-resistant

surface while in use.

NOTICE

DO NOT leave the hood closed for more than 10 minutes while

cooking.

NOTICE

• DO NOT mix old and new batteries.

• DO NOT mix alkaline, standard (carbon-zinc) or rechargeable

(ni-cad, ni-mh, etc.) batteries.

NOTICE

DO NOT place items on stabilizing shelf during use.

TOOLS NEEDED:

Phillips head screwdriver &

Adjustable wrench

TOOL NEEDED:

Phillips head screwdriver

TOOL NEEDED:

Adjustable wrench

TOOL NEEDED:

5mm Allen wrench

NOT INCLUDED:

LPG cylinder

Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)

LPG cylinder must include collar to

protect LPG cylinder valve.

NOT INCLUDED:

17" griddle base

NOT INCLUDED:

22" griddle base

NOT INCLUDED:

AA battery

NOT INCLUDED:

LPG cylinder

Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)

NOT INCLUDED:

AAA battery

TOOLS NEEDED:

Phillips head screwdriver &

Adjustable wrench

TOOL NEEDED:

Phillips head screwdriver

TOOL NEEDED:

Adjustable wrench

TOOL NEEDED:

5mm Allen wrench

NOT INCLUDED:

LPG cylinder

Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)

LPG cylinder must include collar to LPG cylinder must include collar to

protect LPG cylinder valve. protect LPG cylinder valve.

NOT INCLUDED:

17" griddle base

NOT INCLUDED:

22" griddle base

NOT INCLUDED:

AA battery

NOT INCLUDED:

LPG cylinder

Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)

NOT INCLUDED:

AAA battery

MODEL: 

STEP 03 Install the four (4) control knobs by pushing them into place

in the OFF position.

STEP 01 Use four (4) M6 shoulder bolts [a.] to attach the handle

and hood handle stando and two (2) mica washers to the front of

the hood.

STEP 02 Slide the grease cup into the holder on the back of the

griddle body.

[a.] × 4



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALASSEMBLY GUIDE

Make sure the front pins are fully

seated in the holes, then push

the griddle top back to lock the

griddle in place.

Place the two front pins into the

front locking holes and push the

griddle top and hood back. Then,

set the two rear pins into the

rear holes.

Place the two front pins into the

front locking holes and push the

griddle top and hood back. Then,

set the two rear pins into the

rear holes.

Make sure the front pins are fully

seated in the holes, then push

the griddle top back to lock the

griddle in place.

Make sure the front pins are fully

seated in the holes, then push

the griddle top forward to lock

the griddle in place.

Make sure the front pins are fully

seated in the holes, then push

the griddle top forward to lock

the griddle in place.

MODEL: 

STEP 04 Remove the four (4) protective washers from the griddle foot

pins. With the help of another person, place the griddle top onto

the griddle body by aligning the four foot pins to the holes on top of

the unit.

OPTION A: INSTALL AS DROP-IN WITH

INSULATING JACKET

STEP 05 Slide the jacket left inner panel into the jacket left

outer panel.

STEP 06 Slide the jacket right inner panel into the jacket right

outer panel.

STEP 07 Place the jacket rear inner panel into the jacket rear

outer panel.

STEP 08 Place the jacket outer base panel onto the jacket inner

base panel.



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | ASSEMBLY GUIDE MODEL: 

STEP 09 Use four (4) M6x35 screws [c.] to attach the left and right

jacket panel assemblies to the jacket base panel assembly.

STEP 10 Use six (6) M6x15 screws [b.] to attach the rear jacket panel

assembly to the jacket base panel assembly.

STEP 11 Use four (4) M6x45 screws [d.] to secure the rear jacket

panel to the left and right jacket panel assemblies.

Slide the jacket silicon sleeve into the jacket base panel assembly.

STEP 12 With the help of another person, direct the regulator hose

and electric wires through the jacket silicon sleeve and place the

griddle body onto the jacket base panel assembly.

[c.] × 4 [b.] × 6

[d.] × 4



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALASSEMBLY GUIDE

 CAUTION

Heavy pieces. Two people should assemble this appliance.

NOTICE

Place appliance on a heat-resistant and flame-resistant

surface while in use.

NOTICE

DO NOT leave the hood closed for more than 10 minutes while

cooking.

NOTICE

• DO NOT mix old and new batteries.

• DO NOT mix alkaline, standard (carbon-zinc) or rechargeable

(ni-cad, ni-mh, etc.) batteries.

NOTICE

DO NOT place items on stabilizing shelf during use.

NOTICE

The included feet MUST be used when griddle is in the

tabletop configuration.

NOTICE

The insulating jacket must be permanently secured to

cabinet.

DO NOT operate this appliance any closer than 36 in (1 m) from the

sides and back of the appliance to combustible construction.

AA

AAAAAA

AA

WITHOUT JACKET

A: A: 36 in (1 m)36 in (1 m)

 WARNING

The cabinet CAN NOT store 2 or more LPG cylinders.

MODEL: 

STEP 13 ❶❶ Push the 18P male and female connector together.

❷❷ Depress the yellow clip to lock the connector.

❸❸ Push the 3P male and female connector together.

Note: the PCB box must be permanently attached to the cabinet.

STEP 15 Proceed to USING YOUR BLACKSTONE.

STEP 14 Remove the self-tapping screw from the griddle body and

use it to attach the match holder.

Grease cup liner required for use.

❶❶

❷❷

❸❸



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | ASSEMBLY GUIDE

 CAUTION

Heavy pieces. Two people should assemble this appliance.

NOTICE

Place appliance on a heat-resistant and flame-resistant

surface while in use.

NOTICE

DO NOT leave the hood closed for more than 10 minutes while

cooking.

NOTICE

• DO NOT mix old and new batteries.

• DO NOT mix alkaline, standard (carbon-zinc) or rechargeable

(ni-cad, ni-mh, etc.) batteries.

NOTICE

DO NOT place items on stabilizing shelf during use.

NOTICE

The included feet MUST be used when griddle is in the

tabletop configuration.

NOTICE

The insulating jacket must be permanently secured to

cabinet.

DO NOT operate this appliance any closer than 36 in (1 m) from the

sides and back of the appliance to combustible construction.

A

WITHOUT JACKET

A:

36 in (1 m)

 WARNING

The cabinet CAN NOT store 2 or more LPG cylinders.

MODEL: 

OPTION B: FOR NON-COMBUSTIBLE

COUNTERTOP USE

STEP 01 Unscrew the four (4) M6 screws from the hat channels.

Screw the four (4) feet through the hat channels and into the base.

STEP 02 With the help of another person, set on counter. Hose and

cables MUST be routed through the left side.

Proceed to USING YOUR BLACKSTONE.



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

SETTING UP YOUR OUTDOOR SPACE

THIS APPLIANCE MUST ONLY BE USED OUTDOORS.

• DO NOT use this appliance inside buildings, garages, or any other

enclosed area.

• DO NOT install this appliance in or on a boat.

• DO NOT install this appliance in or on a recreational vehicle.

c. Within a partial enclosure that

includes an overhead cover

and three sidewalls, as long as

30% or more of the horizontal

periphery of the enclosure is

permanently open.

b. Within a partial enclosure that

includes an overhead cover

and no more than two side-

walls. The sidewalls may be

parallel, as in a breezeway, or

at right angles to each other.

a. With walls on three sides, but

with no overhead cover.

SHELTERED OUTDOOR AREAS:

All openings must be permanently open; sliding doors, garage doors,

windows or screened openings are not considered as permanent

openings.

An appliance is considered to be outdoors if installed with shelter no

more inclusive than:

MAINTAIN PROPER CLEARANCES FROM COMBUSTIBLE MATERIAL.

• DO NOT use this appliance on or under any apartment or condo-

minium balcony or deck.

• DO NOT obstruct the flow of combustion and ventilation air.

• DO NOT operate this appliance any closer than 36 in (1 m) from the

sides and back of the appliance to combustible construction.

A = 36 in (1 m)

• DO NOT use this appliance under overhead combustible

construction.

BEFORE COOKING

CHECK BURNERS

Before connection, ensure that there is no debris caught in the head

of the gas cylinder, regulator, burner and burner ports.

Spiders and insects can nest within and clog the burner/venturi tube

at the orifice.

Please reference the Troubleshooting chapter for burner cleaning

instructions.

 WARNING

A clogged burner can

lead to a fire beneath the

appliance.

Burner should be removed

and cleaned whenever

blockages are found.

 DANGER

Flammable items can spontaneously combust if placed near

the appliance.

DO NOT place flammable items such as aerosol containers,

oily or greasy towels near the cooking surface.

Keep the outdoor cooking gas appliance area clear and free

from combustible materials, gasoline and other flammable

vapors and liquids.

THE MINIMUM AMBIENT OPERATING TEMPERATURE IS 0°F (-18°C).

 Ensure that the gas

rail fuel nozzle orifice is

correctly engaged within the

burner opening.

A

Both ends open

30%

Venturi

Air intake

Blocked burner

Fuel nozzle

Burner opening

• DO NOT install this appliance under overhead combustible surfaces.

If installed under overhead combustible construction, the appliance must be

installed in conjunction with a suitable UL710 or ULC S646 approved heavy duty

vent hood only.

 WARNING

The cabinet CAN NOT store 2 or more LPG cylinders.

BUILT-IN INSTALLATION

• For installation in a built-in enclosure constructed of combustible

materials when installed with the included insulating jacket.

• DO NOT operate this appliance any closer than 6 in (150mm)

from the sides and back of the appliance to vertical combustible

construction.

A

WITH JACKET

A:

6 in (150 mm)

CAVITY MINIMUM DIMENSIONS

B:

Depth = 27.5 in

C:

Height = 8 in

(>8 in will cause hood interference)

HOLE MINIMUM DIMENSIONS

D:

Distance from side = 10.5 in

E:

Distance from front = 3.75 in

F:

Diameter = 4.5 in

C

E

F

D

B

A

A:

Width = 45.75 in

MODEL: 

USING YOUR BLACKSTONE



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | USING YOUR BLACKSTONE

THE LPG CYLINDER VALVE MUST HAVE:

• Type 1 valve outlet (thread on the outside).

• Safety relief valve.

• UL listed Overfill Protection Device (OPD). This OPD safety feature is

identified by a unique triangular hand wheel.

• Dust cap. LEAK TEST INSTRUCTIONS

• Leak test new and exchanged LPG cylinders BEFORE connecting

to griddle.

• DO NOT smoke during leak test.

• DO NOT use an open flame to check for gas leaks.

• Appliance must be leak tested outdoors in a well-ventilated

area, away from ignition sources such as gas fired or electrical

appliances.

• During leak test, keep appliance away from open flames or sparks.

LEAK TEST: LPG CYLINDER

STEP 01 Use a clean paintbrush

to brush a 10/90 mild soap and

water solution onto joint areas of

the LPG cylinder.

(Indicated by arrows in figure 01.)

• Leaks are indicated by

growing bubbles.

 WARNING

If growing bubbles appear

during leak test, DO NOT use

or move the LPG cylinder.

Immediately contact an LPG

supplier or fire department.

FILLING & ExCHANGE

• Use only those reputable exchange companies that inspect, preci-

sion fill, test and certify their cylinders. LPG dealer must purge new

cylinder before filling.

• Volume of propane in cylinder will vary by temperature.

 WARNING

A frosty regulator indicates gas overfill.

Immediately close LPG cylinder valve and call local LPG

dealer for assistance.

• DO NOT release liquid petroleum gas (LPG) into the atmosphere.

• To remove gas from LPG cylinder, contact a certified LPG dealer or

local fire department for assistance.

• Exchange cylinder only for an OPD safety feature-equipped

cylinder.

Your retailer can help you match a replacement LPG cylinder to your appliance.

LPG CYLINDER REQUIREMENTS

ONLY USE A 20 LB (9 KG) CYLINDER

• The LPG supply cylinder to be used must be constructed and

marked in accordance with the specifications for LP gas cylin-

ders, U.S. Department of Transportation (DOT) or the Standard for

Cylinders, Spheres and Tubes for the Transportation of Dangerous

Goods, CAN/CSA-B339.

• Only LPG cylinders marked “propane” shall be used.

• The LPG cylinder supply system must be arranged for vapor

withdrawal.

•

Always keep new LPG cylinders in upright position during use, transit or

storage.

•

Always keep the ventilation opening(s) of the cylinder enclosure free and

clear from debris.

STORING LPG CYLINDERS

 WARNING

• DO NOT store a spare LPG cylinder under or near this

appliance.

• DO NOT fill an LPG cylinder beyond 80% full.

If the information above is not followed exactly, a fire causing

death or serious injury may occur.

• The LPG cylinder must be turned OFF when the appliance is

not in use.

• LPG cylinders must be stored outdoors and out of the reach

of children.

• DO NOT store an LPG cylinder inside a building, garage, or any other

enclosed area.

The seal on the type 1 valve outlet could, over time, show marked and

visible damage or deterioration that might cause a leak even with

the connection tightened.

• A visual inspection for the seal must be carried out every time a

LPG cylinder is replace or refilled.

• Any LPG cylinder showing signs of damage or deterioration as

those illustrated including visible cracks and pitting, must be

returned unused to the seller.

FITTINGS & HOSES

• Annual checking and tightening of metal fittings is recommended.

• Keep the fuel supply hose away from any heated surfaces.

• Before each use, check to see if hoses are cut or worn.

• Replace damaged hose before using appliance.

(Use only Blackstone approved valve, hose, or regulator. Failure to comply will

void the warranty.)

LPG cylinder valveLPG cylinder valve

Safety relief

valve

OPD hand wheel

Type 1 valve outlet

(check seal before use)

GOOD SEALGOOD SEAL

BAD SEALBAD SEAL

Dust cap

figure 01

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

CONNECT THE LPG CYLINDER

STEP 01 Turn the control

knobs to OFF.

❶

❶ Ensure that the LPG cylinder

is OFF by turning the OPD hand

wheel clockwise to a full stop.

❷

❷ Remove the safety cap from

the Type 1 valve outlet.

STEP 02 Hold the regulator in a

straight line with the Type 1 valve

outlet so as not to cross thread

the connection.

Center and insert the regu-

lator nipple into the Type 1

valve outlet.

Hand-tighten the coupling nut in

a clockwise direction.

(DO NOT use tools to connect.)

If connection cannot be completed,

disconnect regulator and repeat this

step.

LEAK TEST: VALVES, HOSE & REGULATOR

STEP 01 Turn the control knobs to OFF.

STEP 02 Connect the regulator to the LPG cylinder.

STEP 03 Completely open the LPG tank by turning the OPD hand

wheel counterclockwise.

• If you hear a rushing sound, turn gas o immediately. There is a

major leak at the connection.

• Immediately close the LPG cylinder by turning the OPD hand wheel

clockwise and re-tighten connections. If leaks cannot be stopped

DO NOT TRY TO REPAIR.

STEP 04 Use a clean paintbrush

to brush a 10/90 mild soap and

water solutionn onto joint areas

of valves and regulator.

(Indicated by arrows in figure 02.)

• Leaks are indicated by

growing bubbles.

• Immediately close the LPG

cylinder by turning the OPD

hand wheel clockwise and

re-tighten connections.

 WARNING

If leaks cannot be stopped, DO NOT try to repair.

Regulator must be replaced with a Blackstone approved

model by a professionally licensed, authorized dealer.

The safety relief valve must face

away from the user while the

appliance is in use.

DISCONNECTING THE LPG CYLINDER

20 LB (9 KG)

STEP 01 Ensure that the control knobs are turned to OFF.

❶

❶ Ensure that the LPG cylinder

is OFF by turning the OPD hand

wheel clockwise to a full stop.

❷

❷ Turn the coupling nut count-

er-clockwise by hand to remove

the regulator. (DO NOT use tools

to disconnect.)

STEP 02 Place dust cap on LPG

cylinder valve outlet whenever

cylinder is not in use.

Only install the type of dust cap on

cylinder valve outlet that is provided

with the cylinder valve. Other types of

caps or plugs may result in leakage of

propane.

REGULATOR SAFETY

• Use this appliance, as purchased, only with gas and regulator/valve

assembly supplied.

• DO NOT cross thread the connection between your LPG cylinder

and regulator.

Cross threading can occur if you force thread a connection at an improper

angle. This will damage the threads, lead to propane leaking, and potentially

result in a build-up of fuel that can ignite.

• If you can not connect the regulator, DO NOT use the regulator.

Regulator must be replaced with a Blackstone approved model by a profession-

ally licensed, authorized dealer.

❶❶

❷

Coupling nutCoupling nut

Regulator nippleRegulator nipple

figure 02

❶❶

❷

STEP 03 Set the LPG cylinder into

the propane cabinet.

ENCLOSURE CONSTRUCTION

A:

4 in x 6 in vents at top and bottom,

and both sides of cabinet.

B:

Plenum wall to separate the LPG

cylinder compartment.

C:

LPG cylinder access door.

A

C

B

Use an LPG cylinder retention

system to prevent the cylinder

from tipping over.

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | USING YOUR BLACKSTONE

Turn gas ON at the LPG cylinder

by turning the OPD hand wheel

counterclockwise 1 to 3 turns.

2. BATTERY POWERED IGNITION

 DO NOT lean over the appliance while lighting.

STEP 01 Insert one (1) AA

battery (not included) under the

ignitor button.

Screw the button into place over

the positive terminal.

STEP 02

❶ ❶ Turn the control knob to OFF.

STEP 03

❷❷ Push and hold the ignitor button.

❸❸ Push and turn the control knob counter-clockwise to HIGH.

(Release the ignitor button when the burner lights.)

❹❹ Adjust the temperature to desired level.

IGNITION INSTRUCTIONS

1. CHECK VALVES

STEP 01 Turn knob to OFF position.

STEP 02 Push in knob and release. Knob should spring back.

If knobs

DO NOT

spring back, replace valve assembly before using appliance.

STEP 03 Rotate knob to LOW then turn back to OFF. Knob should

turn smoothly.

 WARNING

If burner does not ignite with open LPG cylinder valve, gas

will continue to flow out of burner and could accidentally/

inadvertently ignite with risk of injury.

Ensure gas is o at the supply shut o valve before checking

appliance valves.

❷❷

❸❸

❶❶

❹❹

1 to 3 turns1 to 3 turns

STEP 02

❶

❶ Push the control knob in to

start gas flowing. (WHITE)

❷

❷ Turn the control knob

counter-clockwise to activate the

starter. (FLASHING BLUE)

❸

❸ Adjust the temperature to

desired level. (ORANGE)

STEP 01 Press the ON button.

(Optional: Turn the dimmer

until it clicks to turn o the

puddle lights.)

2. ELECTRIC IGNITION

 DO NOT lean over the appliance while lighting.

Make sure the appliance is plugged in.

❷

❶

❸

Note: If the magnet in the knob is disconnected, the indicator light

will be orange. If the knob arrow is facing UP, gas is not flowing.

HEALTHY BURNER FLAME

PATTERN

HEALTHY BURNER FLAME

PATTERN

BURNER FLAMES ARE YELLOW

OR IRREGULAR

BURNER FLAMES ARE YELLOW

OR IRREGULAR

3. CHECK BURNER FLAME

Always check burner flame before use.

STEP 01 Light burners and rotate knobs from HIGH to LOW.

STEP 02 Look below the cooking top to view burners. When knob is at

HIGH, flames should be larger than when knob is at LOW.

3. CHECK BURNER FLAME

Always check burner flame before use.

STEP 01 Light burner and rotate knob from LOW to HIGH.

STEP 02 Look below the turntable to view burner. When knob is at

HIGH, flames should be larger than when knob is at LOW.

❶

❶ Flickers of yellow color.

❷

❷ Dark blue color.

❸

❸ Vibrant blue.

❶ ❶ Flickers of yellow color.

❷ ❷ Dark blue color.

❸ ❸ Vibrant blue.

If there is a sudden drop or low

flame issue, please reference the

Troubleshooting chapter.

If there is a sudden drop or low

flame issue, please reference the

Troubleshooting chapter.

❶

❷

❸

❶❶

❷❷

❸❸

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

WHAT OIL IS BEST TO USE?

• Blackstone Seasoning and

Cast Iron Conditioner.

• Any plant-based cooking oil.

• Rendered animal fat with no

additives.

WASHING YOUR GRIDDLE TOP BEFORE FIRST USE

NOTICE

Soap will ruin a seasoned griddle. This is the only time you

should use soap on the griddle cooking surface.

STEP 01 Wash the griddle cooking surface with hot, soapy water.

STEP 02 Rinse and dry completely.

STEP 01 Wipe any debris o

griddle top.

GRIDDLE SEASONING INSTRUCTIONS

STEP 02 Set your griddle to

high heat until your griddle top

changes color. (~10 min)

STEP 04 The griddle top is ready

for another layer of oil when it

stops smoking. Repeat STEP 03

3-4 times, or until the griddle

surface is black.

SEASONING TROUBLESHOOTING

THERE IS A BROWNISH RESIDUE ON THE GRIDDLE SURFACE:

VIDEO TUTORIAL

How to Season a New Blackstone Griddle

 youtube.com/watch?v=VspmDVnj2pI&t=3s

STEP 03 Use tongs to hold a

paper towel or cotton cloth and

spread 2-3 tablespoons of your

seasoning oil across the entire

griddle top.

When seasoning your griddle top,

remember to use a thin and even layer

of oil—the thinner the layer of oil, the

easier it will be to burn it o.

VIDEO TUTORIAL

Recovering your Blackstone Griddle Top

 youtube.com/watch?v=thPE2IgnSiI

PREVENTING RUST

Use your griddle frequently. Every time you cook, you are adding to

the seasoning, which makes rust less likely.

NOTICE

If you live in a humid or coastal climate, your griddle may

require more frequent seasonings between uses.

If rust appears on the griddle surface, rub it o with steel wool, low

grit sandpaper or the Blackstone Pumice Stone and re-season

the surface.

THE EDGES OF THE GRIDDLE SURFACE ARE NOT BLACK:

After using your griddle for multiple cooks, the seasoning will even

out and improve.

POSSIBLE CAUSES SOLUTION

• Too much oil was used.

• You turned o the heat too

soon.

STEP 01 Turn your griddle on high

and let it heat for 10-15 minutes.

STEP 02

Scrape o as much

of the thickened and partially

cooked oil as you can.

STEP 03

Re-season with a very

thin layer of oil.

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | USING YOUR BLACKSTONE

COOKING ON YOUR BLACKSTONE

 CAUTION

This appliance will be hot during and after use. Use long-

handled utensils and oven mitts/ protective gloves when

handling potentially hot parts to protect against burns and

splatters.

NOTICE

DO NOT store any items within 3 in (8 cm) of the cooking

surface while in use.

IF GREASE OR OTHER HOT MATERIAL DRIPS ONTO VALVE, HOSE OR

REGULATOR:

STEP 01 Turn o gas supply immediately.

STEP 02 Determine the cause and correct it.

STEP 03 Clean and inspect valve, hose and regulator.

STEP 04 Perform a leak test. (Please reference the Leak Test

Instructions in USING YOUR BLACKSTONE.)

VIDEO RECIPES

Find recipes and cooking tips at:

 BlackstoneProducts.com/blogs/recipes

 youtube.com/c/BlackstoneGriddles

   @blackstoneproducts

STRAWBERRIES AND CREAM

PANCAKES

Breakfast

TACOS BORRACHOS

Dinner

OKLAHOMA FRIED ONION

BURGER

Lunch

CLEANING YOUR GRIDDLE TOP

Clean griddle top after each use, while still warm.

• DO NOT use soap on the griddle top. This will destroy the griddle’s

seasoning.

• The grease cup must be removed and emptied after each use.

 CAUTION

Grease cup will be hot during and after use. DO NOT remove

the grease cup until the griddle has completely cooled.

STEP 01 Push loose food debris

into the grease cup with spatula

or straight metal scraper.

STEP 02 Wipe down griddle top

with paper towel.

STEP 03 Apply a few tablespoons

of water to the griddle surface,

then scrape the water and debris

into the grease cup.

(For stuck-on food residue, use a

bit of coarse salt.)

STEP 04 Wipe again with a paper

towel and dry completely.

STEP 05 Apply thin coat

of cooking oil to maintain

seasoning and protect the

griddle top.

VIDEO TUTORIAL

How to Clean your Blackstone Griddle

 youtube.com/watch?v=-Iedu9z6NPY

HOW TO USE YOUR PIZZA OVEN

FRESH PIZZA

STEP 01 Preheat oven using the QUICK START GUIDE method. For

best results, use an infrared thermometer (not included) to measure

the bottom stone temperature. For fresh dough pizza, 650°-700° F

(340°-370° C) is a good starting point but you will need to adjust

depending on the dough you are using.

STEP 02 Once the desired temperature is reached, turn the control

knob to adjust throughout the duration of the cooking time to

achieve desired result.

STEP 03 Pizza cooking time is about 2-4 minutes depending on the

size and thickness of the pizza.

a. Thinner foods should be cooked at a higher temperature for a

shorter time.

b. Thicker or denser foods should be cooked at a lower temperature

for a longer time.

STEP 04 Pull the pizza out when the crust has reached your desired

readiness, or when the edges of the pizza crust are golden-brown.

FROZEN PIZZAS, COOKIES, ETC.

Follow the food manufacturer’s directions on box/ recipe.

(Let frozen food thaw a little bit before putting into the hot oven. This

will prevent your pizza stone from cracking.)

CLEANING YOUR OVEN INTERIOR

If the pizza falls o the rotating stone and catches on fire:

STEP 01 Turn OFF the control knob, turn OFF the LPG cylinder, turn

OFF the rotating motor.

STEP 02 Allow the oven to completely cool.

STEP 03 Remove the oven lid, the top stone, and the lower stone.

STEP 05 Use a spatula to scrape and remove debris from cooking

cavity floor. Wipe cooking cavity with a damp cloth. DO NOT use

detergent.

STEP 06 Use a vacuum if necessary to clean out food debris inside

cooking chamber.

If necessary, reference the Troubleshooting chapter for instructions on If necessary, reference the Troubleshooting chapter for instructions on

cleaning the burner.cleaning the burner.

STEP 04 Remove the turntable

by removing the two (2) bolts

that attach the turntable to the

rotating shaft.

CLEANING YOUR PIZZA STONE

STEP 01 Set your oven to HIGH for 15~20 min to burn o residue.

STEP 02 Once your oven has cooled completely, flip the stone over

and use the cleaner side.

Note: The top and bottom stones are interchangeable.

NOTICE

DO NOT use soap on the cooking stone. This will leave a soap

taste in food.

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

APPLIANCE STORAGE

 WARNING

DO NOT move the appliance when in use. Allow the appliance

to cool to 115°F (45°C) before moving or storing.

Storage of an appliance indoors is only permissible if the gas supply

is disconnected and removed from the appliance.

COVER FIT GUIDE

Always cover your appliance when stored outdoors.

To find a cover that will fit your appliance, visit

BlackstoneProducts.com/support.

CLEANING YOUR APPLIANCE

 WARNING

Grease build up can cause a fire. Clean any part of the

appliance that gets hot and experiences grease build up after

each use.

 CAUTION

All cleaning and maintenance should be carried out when the

appliance is cool and with the fuel supply turned OFF at the

LPG cylinder.

• DO NOT use abrasive pad on areas with graphics.

• If a bristle brush is used to clean any of the cooking surfaces,

ensure no loose bristles remain on cooking surfaces prior

to cooking.

PLASTIC PARTS & PAINTED SURFACES:

Wash with warm soapy water and wipe dry with a non-abra-

sive cloth.

NOTICE

DO NOT use Citrisol, abrasive cleaners, or a concentrated

cleaner on plastic parts. This may result in damage to and

failure of parts.

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | TROUBLESHOOTING

POSSIBLE CAUSES SOLUTION

Something is blocking the

venturi in the burner.

Clean the burner assembly to

remove the obstruction.

POSSIBLE CAUSES SOLUTION

Obstructions in the burner, gas

jets, or fuel rail.

Clean the burner, jets, and gas

hose.

LPG cylinder is empty or low.

Refill or replace the LPG

cylinder.

The regulator’s flow limiting

device was triggered.

Reset the safety system:

STEP 01

Turn OFF the appliance,

close the LPG cylinder valve, and

disconnect the regulator from

the LPG cylinder.

STEP 02

Wait five minutes to

allow the pressure to dissipate,

then reconnect the regulator

to the LPG cylinder and slowly

open the OPD hand wheel one

half turn.

STEP 03

Ignite your appliance.

Regulator stuck in safety

position. Contact customer support for

replacement parts.

GAS FLOW TROUBLESHOOTING

A FLAME IS COMING OUT OF THE AIR GATE:

BURNER FLAMES ARE YELLOW OR IRREGULAR:

• Appliance will not achieve a high heat or heats unevenly.

• Burner flames start strong, then immediately drop to low even

when burner is set to high position.

• Flame height drops when a second burner is lit.

• Flames DO NOT extend the full length of the burner, or only run on

one side of the burner.

• Burner flames are inconsistent.

IF YOU CAN IGNITE YOUR APPLIANCE WITH A MATCH:

POSSIBLE CAUSES SOLUTION

Ignitor wire misaligned.

Ensure that the ignition needle

is positioned 3-7mm away from

the burner tube, and above a

burner hole.

Damage to the ignition system.

Contact customer support for

replacement parts.

IF YOU CAN NOT IGNITE YOUR APPLIANCE WITH A MATCH:

POSSIBLE CAUSES SOLUTION

Burner tubes are not receiving

fuel. Clean the burner assembly to

remove the obstruction.

3-7mm

IGNITION TROUBLESHOOTING

BURNER WILL NOT IGNITE:

If ignition does not occur in 5 seconds:

STEP 01 Turn the burner control knob OFF.

STEP 02 Wait 5 minutes.

STEP 03 Repeat the lighting procedure.

If this does not work, to determine the cause, please try to ignite your appli-

ance with a match.

IGNITION TROUBLESHOOTING

BURNER WILL NOT IGNITE:

If ignition does not occur in 5 seconds:

STEP 01 Turn the burner control knob OFF.

STEP 02 Wait 5 minutes.

STEP 03 Repeat the lighting procedure.

If this does not work, to determine the cause, please try to ignite your appli-If this does not work, to determine the cause, please try to ignite your appli-

ance with a match. ance with a match.

MATCH LIGHTING INSTRUCTIONS

Before beginning, check for gas leaks. Open hood (if applicable).

STEP 01 Turn control knob to OFF position.

MATCH LIGHTING INSTRUCTIONS

Before beginning, check for gas leaks. Before beginning, check for gas leaks.

STEP 01 Turn control knob to OFF position.

STEP 04 Push in and turn the control knob to start gas flowing.

Ensure burner lights and stays lit.

STEP 04 Push in and turn the control knob to start gas flowing.

Ensure burner lights and stays lit.

STEP 02 Light a match (or long

lighter) no shorter than 11

inches long.

STEP 03 Place the flame next to

the burner.

STEP 02 Light a match (or long

lighter) no shorter than 11

inches long.

STEP 03 Place the flame next to

the burner.

MODEL: 

TROUBLESHOOTING



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALTROUBLESHOOTING

CUSTOMER SUPPORT

Visit us online at blackstoneproducts.com/support

for assistance concerning appliance use, replacement parts, or

your warranty.

CUSTOMER SUPPORT HOURS:

 Monday – Friday

7:00 am – 5:00 pm (MST)

STEP 06 Carefully replace

burners and reattach, with

attention to the location of the

ignition needle.

STEP 01 Ensure that the gas is turned OFF at control knobs and gas

supply. Remove the griddle top.

CLEANING THE BURNER ASSEMBLY

To reduce chance of “flash-back” the procedure below should be

followed at least once a month when spiders are most active or

when your appliance has not been used for a period of time.

STEP 02 Carefully detach and

remove the burner.

STEP 03 Clean the inside of

the burner:

• Run a narrow bottle brush

through each burner tube

several times. (DO NOT use

wire brushes)

• Run a sti wire bent into a small

hook through each burner tube

several times.

• Use compressed air to blow

through the burner tube and

out the burner ports. Check that

air blows through each hole.

(Wear eye protection)

STEP 04 Brush entire

outer surface of burner to

remove grime.

STEP 05 Clean any blocked ports

with sti wire such as an open

paper clip.

VIDEO TUTORIAL

How to Clean Your Burner Tube

 youtube.com/watch?v=xKQTCrFCzf8

 The gas rail fuel nozzle

must be reengaged within the

burner opening.

Fuel nozzle

Burner opening

CUSTOMER SUPPORT

Visit us online at BlackstoneProducts.com/support

for assistance concerning appliance use, replacement parts, or

your warranty.

CUSTOMER SUPPORT HOURS:

 Monday – Friday

7:00 am – 5:00 pm (Mountain Time)

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

This product may be covered by one or more issued U.S. and/or

international patents and may include patent applications pending.

For more information, please visit: BlackstoneProducts.com/patents

DISTRIBUTED BY NORTH ATLANTIC IMPORTS, LLC  W  N LOGAN, UT  USA | BLACKSTONE IS A REGISTERED TRADEMARK OF NORTH ATLANTIC IMPORTS, LLC



La page charge ...

Blackstone 6038 36 Inch Griddle Drop-In Le manuel du propriétaire

Blackstone 6038 36 Inch Griddle Drop-In Le manuel du propriétaire

dans d''autres langues

Documents connexes