Skil QC5359B-02 Le manuel du propriétaire

Marque: Skil

Modèle: QC5359B-02

Taper: Le manuel du propriétaire

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente 1-877-SKIL-999 OR www.skil.com

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

20V Dual Port Charger

Chargeur à double port de 20 V

Cargador de puerto dual de 20 V

Model/ Modelo/ Modèle: QC5359B-02

TABLE OF CONTENTS

Charger Safety Instructions ....................................3-4

Extension Cords ................................................4

FCC Caution ....................................................5

Symbols .....................................................6-9

Get to Know Your Charger .......................................10

Specications .................................................10

Important Charging Notes .......................................11

Operating Instructions .......................................12-13

Maintenance ...................................................14

Troubleshooting ...............................................14

Limited Warranty of SKIL Consumer Tools ..........................15

IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE

INSTRUCTIONS

DANGER TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY

FOLLOW THESE INSTRUCTIONS.

CHARGER SAFETY INSTRUCTIONS

Save these instructions. This manual contains important safety and operating instructions

for battery charger model QC5359B-02 Before using battery charger, read all instructions

and cautionary markings on battery charger, battery and product using battery.

CAUTION To reduce risk of injury, charge only SKIL rechargeable batteries

listed in the manual. Other types of batteries may burst causing personal

injury and damage.

Charge battery pack within the required temperature range. Store charger and battery

pack in locations where temperature is within the recommended storage temperature

range. This is important to prevent serious damage to the battery cells.

Do not recharge battery in damp or wet environment. Do not expose charger to rain or

snow. Water entering battery charger may result in electric shock or re.

Battery leakage may occur under extreme usage or temperature conditions. Avoid

contact with skin and eyes. The battery liquid is caustic and could cause chemical burns

to tissues. If liquid comes in contact with skin, wash quickly with soap and water. If the liquid

contacts your eyes, ush them with water for a minimum of 10 minutes and seek medical

attention.

Place charger on flat nonflammable surfaces and away from flammable materials when

recharging battery pack. Carpeting and other heat insulating surfaces block proper air

circulation which may cause overheating of the charger and battery pack. If smoke or melting

of the charger or battery pack is observed, unplug the charger immediately and do not use the

battery pack or charger. Contact customer service immediately.

Keep the cord and charger from heat to prevent damage to housing or internal parts.

Do not allow gasoline, oils, petroleum-based products, etc. to come in contact with

plastic parts. These materials contain chemicals that can damage, weaken, or destroy

plastic.

Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress. Damaged plug and cord may result in electric shock or re.

Disconnect the charger by pulling the plug rather than the cord. Do not operate charger

with damaged cord or plug; have them replaced immediately. Damaged plug or cord may

result in electric shock or re.

Do not insert battery pack in charger if battery pack case is cracked. Using damaged

battery pack may result in electric shock or re.

Do not disassemble charger or operate the charger if it has received a sharp blow, been

dropped or otherwise damaged in anyway. Incorrect reassembly or damage may result in

electric shock or re.

Before each use, check the battery charger, cable and plug. If damage is detected, do

not use the battery charger. Never open the battery charger yourself, take it to a SKIL

Factory Service Center, or qualified serviceman only using original spare parts.

Incorrect reassembly may result in electric shock or re.

Do not touch the uninsulated portion of output connector or uninsulated battery

terminal. There is a risk of electric shock.

Do not use attachment not recommended or sold by SKIL. Using attachments not

recommended may result in electric shock or re.

Do not store battery pack in charger. Battery pack stored in charger over a long period of

time could lead to battery pack damage and re.

Unplug charger from outlet before storage, attempting any maintenance or cleaning.

Such preventive safety measures reduce the risk of electric shock or re.

Keep the battery charger clean by blowing compressed air on charger vents and wiping

the charger housing with a damp cloth. Contamination may result in electric shock or re.

Replace battery pack if a substantial drop in operating time per charge is observed.

Battery pack may be nearing the end of its life.

To reduce the risk of injury, close supervision is necessary when an appliance is used

near children.

Do not use outdoors.

DANGER People with electronic devices, such as pacemakers, should consult

their physician(s) before using this product. Operation of electrical

equipment in close proximity to a heart pacemaker could cause interference or failure

of the pacemaker.

EXTENSION CORDS

WARNING AN EXTENSION CORD SHOULD NOT BE USED UNLESS

ABSOLUTELY NECESSARY. Use of improper extension cord could result

in risk of re and electrical shock. If an extension cord is used, make sure:

a. The pins on plug of extension cord are the same number, size, and shape as those of plug

on charger.

b. The extension cord is properly wired and in good electrical condition.

c. The wire size is large enough for AC ampere rating of charger as specied below:

Length of Cord (Feet) 25’ (7.5m) 50’ (15m) 100’ (30.5m) 150’ (45.5m)

Size of Cord (AWG) 18 16 16 14

Extension Cord Chart for 220/240 Volt Tools:

0.75mm2 CORD 50 Meters

1.0mm2 CORD 75 Meters

d. An extension cord is a temporary solution. Move the charger to a standard receptacle as

soon as the job has been completed.

FCC CAUTION

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause

undesired operation.

2. Changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and the explanations with them deserve your careful attention and understanding.

The symbol warnings do not, by themselves, eliminate any danger. The instructions and

warnings they give are no substitutes for proper accident prevention measures.

WARNING Be sure to read and understand all safety instructions in this Owner's

Manual, including all safety alert symbols such as “DANGER,”

“WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not followed.

WARNING The operation of any power tools can result in foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always use

eye protection which is marked to comply with ANSI Z87.1.

SYMBOLS (CONTINUED)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and more safely.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

WWatt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-hours Battery capacity

øDiameter Size of drill bits, grinding wheels, etc.

n0No load speed Rotational speed, at no load

nRated speed Maximum attainable speed

…/min Revolutions or reciprocations per

minute (rpm)

Revolutions, strokes, surface speed,

orbits, etc. per minute

OOff position Zero speed, zero torque...

1,2,3,…

Ⅰ,Ⅱ,Ⅲ, Selector settings Speed, torque, or position settings.

Higher number means greater speed

Innitely variable selector with off Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current (AC) Type or a characteristic of current

Direct current (DC) Type or a characteristic of current

Alternating or direct current

(AC / DC) Type or a characteristic of current

Class II tool Designates Double Insulated Construction

tools.

Protective earth Grounding terminal

Li-ion RBRC seal Designates Li-ion battery recycling

program

Read the instructions Alerts user to read manual

Symbol Name Designation/Explanation

Wear eye protection symbol Alerts user to wear eye protection

Always operate with two hands Alerts user to always operate with two

hands

Do not use the guard for cut-off

operations

Alerts user not to use the guard for

cut-off operations

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT: Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this component is recognized by

Underwriters Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

GET TO KNOW YOUR CHARGER

20V Dual Port Charger

Charging Indicator

Fig. 1

Error Indicator

Charging Indicator

SPECIFICATIONS

Rated input 120V a.c., 60Hz, 2×150W

Battery pack

compatibility

2.0Ah:

SKIL BY519701

SKIL BY519702

2.5Ah:

SKIL BY519703 4.0Ah:

SKIL BY519601 5.0Ah:

SKIL BY519603

Recommended

charging

temperature 41°F – 95°F (5 – 35°C)

Recommended

storage

temperature 32°F – 104°F (0 – 40°C)

WARNING This charger will only charge the battery packs listed in the table

above. Other types of batteries may burst causing personal injury and

damage.

NOTE: Use of chargers or battery packs not sold by SKIL will void the warranty.

IMPORTANT CHARGING NOTES

1. A substantial drop in operating time per charge may mean that the battery pack is nearing

the end of its life and should be replaced.

2. Remember to unplug the charger during storage.

3. If battery does not charge properly:

a. Check for power at the outlet by plugging another electrical device into the outlet.

b. Check to see if outlet is connected to a light switch that turns power “off” when the lights

are turned off. If it is, make sure that the switch is set to “on”.

c. Check the battery pack terminals for dirt. Clean with a cotton swab and alcohol, if

necessary.

d. If proper charging still does not occur, take or send the tool, battery pack, and charger to

your local SKIL Service Center. Please refer to the Customer Service information on the

cover of this manual.

OPERATING INSTRUCTIONS

WARNING To reduce the risk of fire, personal injury, and product damage due to

a short circuit, never immerse your charger or battery pack in fluid or

allow a fluid to flow inside them. Corrosive or conductive uids, such as seawater, certain

industrial chemicals, and bleach or bleach-containing products, etc. can cause a short circuit.

WARNING Do not attempt to modify the charger or create accessories not

recommended for use with this charger. Any such alteration or

modication is misuse and could result in a hazardous condition leading to possibly serious

personal injury.

How to Charge the Battery Pack

(Fig. 2)

NOTICE: The battery pack is shipped partially

charged. Before using it the rst time, fully

charge the battery pack. This charger can

charge a single battery pack or two battery

packs at the same time.

a. Charge only compatible battery packs listed

in SPECIFICATIONS earlier in this manual.

b. Connect the charger to a power supply

(120V~, 60Hz). All indicators on the charger

will ash once, indicating that the charger

self-inspection is completed.

c. Align the raised ribs of the charger with the

slot in the battery pack.

d. Insert the battery pack into the charger.

e. The charger will communicate with the battery pack to evaluate the condition of the battery

pack.

f. If the battery pack temperature is within the charging temperature range, the charger will

automatically start charging the battery pack. The green charging indicator will ash during

charging.

g. After the charging is complete, the green charging indicator will remain glowing green,

without ashing. Remove the battery pack from the charger and disconnect the charger

from the power supply, unless you are charging another battery pack.

h. A steady red error indicator means that the battery is over or under the optimal temperature.

Remove the battery pack from the charger. If the battery is too hot, cool the battery under

air ow. If the battery is too cold, place it indoors until it reaches room temperature.

i. It is not recommended that the battery pack remain on the charger for more than 24 hours.

NOTE: If the battery pack cannot accept a charge, the contacts of the charger or battery pack

may be contaminated. Clean the contacts of the charger or battery pack (e.g., by inserting

and removing the battery pack several times or cleaning with a cotton swab and alcohol) or

replace the battery pack, as required.

Fig. 2

Attach

Detach

Charger Display

Mode Charging Indicator

(green) Error Indicators

(red) Fuel Gauge on

Battery Pack Note

Self-inspection

completed Flash once Flash once Off All the four

indicators ash once

Self-inspection failed Either or both are off Off

At least one will

have no reaction

when the charger is

plugged in.

Normal Charging Flashing Off

Flashing

according to

the current

capacity level.

The charger will

automatically start

charging the battery

pack, if the battery

pack temperature is

within the charging

temperature range.

Fully Charged Steady Off Off

Hot/Cold Battery Off Steady Off Remove the battery

from the charger.

Error Off Flashing or Off Off Charging Error.

NOTICE: Charger may become warm with several continuous charge cycles. This is part of

the normal operation of the charge. Charge in a well-ventilated area.

Charger Error

If the charger self-inspection fails to react when the charger is plugged in, the causes include

no power to the charger, bad contacts, or a charger failure. Check to see if the charger self-

inspection can be activated when the charger is plugged in again or plugged into a different

outlet. If it still fails, have the charger serviced by an Authorized SKIL Service Station.

Battery Pack Error

If the charger detects a problem, the red Error Indicator will begin ashing. Remove and

reinsert the battery pack in the charger. If the Error Indicator still ashes, try charging a

different battery pack.

a. If a different battery pack charges normally, have the rst failed battery pack serviced by an

Authorized SKIL Service Station.

b. If a different battery pack also fails to charge, the problem may be with the charger. Have

the charger serviced by an Authorized SKIL Service Station.

MAINTENANCE

Service

WARNING Preventive maintenance performed by unauthorized personnel may

result in misplacing of internal wires and components which could

cause serious hazard. We recommend that all tool service be performed by a SKIL Factory

Service Center or Authorized SKIL Service Station.

General Maintenance

WARNING When servicing, use only identical replacement parts. Use of any

other parts could create a hazard or cause product damage.

Periodically inspect the entire product for damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Please contact customer service or an authorized service center for

assistance.

Cleaning

WARNING To avoid serious personal injury, always remove the battery packs

from the charger/tool when cleaning.

The tool may be cleaned most effectively with compressed dry air.

WARNING Always wear safety goggles when cleaning tools with compressed

air. Do not attempt to clean by inserting pointed objects through openings.

WARNING Certain cleaning agents and solvents damage plastic parts. Some of

these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia and household detergents that contain ammonia.

Storage

Store the charger indoors in a place that is inaccessible to children. Keep away from corrosive

agents.

TROUBLESHOOTING

Problem Cause Remedy

Battery pack will not

charge. 1. Charger is not plugged into

a functioning outlet.

2. Battery pack is not properly

inserted into the charger.

3. Bad contacts.

4. Battery pack is too hot or

cold.

5. Battery pack is damaged.

6. Charger is damaged.

1. Conrm that the charger is plugged

into a functioning outlet.

2. Conrm that the battery pack is

inserted into the charger completely.

3. Unplug the charger from power

outlet. Clean the contacts of the

charger or battery packs.

4. Cool the battery pack if it is too hot.

Place the battery indoors if it is too

cold.

5. Have the battery pack serviced by

an Authorized SKIL Service Station.

6. Have the charger serviced by an

Authorized SKIL Service Station.

LIMITED WARRANTY OF SKIL CONSUMER TOOLS

2 YEAR LIMITED WARRANTY

Chervon North America, Inc. (“Seller”) warrants to the original purchaser only, that all SKIL

consumer BATTERIES AND CHARGERS will be free from defects in material or workmanship

for a period of two years from date of purchase.

Product registration can be completed online at www.Registermyskil.com. Original purchasers

should also retain their receipt as proof of purchase.

Notwithstanding the foregoing, if a SKIL consumer portable power tool is used for industrial,

professional or commercial purposes, the foregoing warranty wil apply for a duration of ninety

days, regardless of registration.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall

be the repair or replacement of parts, without charge, which are defective in material or

workmanship and which have not been misused, carelessly handled, or repaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty,

you must return the complete product, transportation prepaid, to any SKIL Factory Service

Center or Authorized Service Station.

For Authorized SKIL Power Tool Service Stations, please visit www.Registermyskil.com or call

1-877-SKIL-999 (1-877-754-5999).

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS

CIRCULAR SAW BLADES, DRILL BITS.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN

DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE

TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME STATES

IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO

YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)

ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.

AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE

TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED

STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR

WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL

DEALER OR IMPORTER.

TABLE DES MATIÈRES

Consignes de sécurité relatives au chargeur. ....................17-18

Rallonges .....................................................18

Mise en garde de la FCC

(Commission fédérale des communications des États-Unis) ...........19

Symboles ..................................................20-23

Apprenez à connaître votre chargeur ..............................24

Spécications .................................................24

Remarques importantes concernant la charge ......................25

Instructions pour l’utilisation ..................................26-27

Entretien ......................................................28

Recherche de la cause des problèmes .............................29

Garantie limitée du chargeur SKIL .................................30

CONSIGNES DE SÉCURITÉ IMPORTANTES – À CONSERVER

INSTRUCTIONS

DANGER SUIVEZ RIGOUREUSEMENT CES INSTRUCTIONS AFIN DE RÉDUIRE

LES RISQUES D’INCENDIE OU DE CHOC ÉLECTRIQUE.

CONSIGNES DE SÉCURITÉ RELATIVES AU CHARGEUR

Conservez ces instructions. Ce guide contient des instructions de sécurité et de

fonctionnement importantes sur le chargeur QC5359B-02.

Avant d’utiliser le chargeur, lisez l’ensemble des instructions et des avertissements sur

le chargeur, sur la pile et sur l’appareil utilisant la pile.

MISE EN GARDE Lorsqu’un appareil est utilisé en présence d’enfants,

chargez uniquement les piles SKIL rechargeables

mentionnées dans ce guide. Les autres types de piles pourraient exploser et ainsi causer

des blessures ou des dommages.

Chargez le bloc-piles dans la plage de température prescrite. Rangez le chargeur et

le bloc-piles dans un endroit où la température se situe dans la plage de température

de rangement recommandée. Cela est important pour éviter d’endommager gravement les

piles.

Ne rechargez pas le bloc-piles dans un endroit humide ou mouillé. N’exposez pas le

chargeur à la pluie ou àla neige. Une inltration d’eau dans le chargeur peut causer un choc

électrique ou un incendie.

Il se peut que le bloc-piles fuie dans des conditions d’utilisation intenses ou de

températures extrêmes. Évitez tout contact avec la peau et les yeux. Le liquide du bloc-

piles est caustique et peut causer des brûlures chimiques aux tissus. Si le liquide entre

en contact avec la peau, lavez-la rapidement avec de l’eau et du savon. Si le liquide entre en

contact avec vos yeux, rincez-les immédiatement avec de l’eau pendant au moins 10 minutes

et consultez un médecin.

Placez le chargeur sur une surface plate ininflammable et à l’écart des matériaux

inflammables lors de la recharge du bloc-piles. La moquette et les autres surfaces

calorifuges bloquent la circulation de l’air, ce qui peut entraîner une surchauffe du chargeur

et du bloc-piles. Si vous percevez de la fumée ou remarquez que le chargeur ou le bloc-piles

a fondu, débranchez immédiatement le chargeur et n’utilisez pas le bloc-piles ou le chargeur.

Communiquez immédiatement avec le service à la clientèle.

Gardez le cordon et le chargeur loin de la chaleur pour éviter d’endommager le boîtier

ainsi que les pièces internes.

Ne laissez pas de l’essence, des huiles, des produits à base de pétrole, des huiles

dégrippantes ni d’autres produits de ce genre entrer en contact avec les pièces en

plastique. Ces matières contiennent des produits chimiques pouvant endommager, affaiblir

ou détruire le plastique.

Veillez à ce que le cordon ne soit pas placé dans un endroit où l’on pourrait marcher

dessus, l’accrocher ou lui faire subir un dommage ou une contrainte. Une fiche ou un

cordon endommagé peuvent entraîner un choc électrique ou un incendie.

Débranchez le chargeur en tirant sur la fiche plutôt que sur le cordon. N’utilisez

pas le chargeur si le cordon ou la fiche sont endommagés et faites-les remplacer

immédiatement le cas échéant. Une che ou un cordon endommagés peuvent entraîner un

choc électrique ou un incendie.

N’insérez pas le chargeur dans le bloc-piles si ce dernier est fissuré ou endommagé.

L’utilisation d’un bloc-piles endommagé peut causer un choc électrique ou un incendie.

Ne démontez pas et n’utilisez pas le chargeur si celui-ci a reçu un coup violent, s’il est

tombé par terre ou s’il a été endommagé d’une quelconque façon. Un réassemblage

incorrect ou des dommages peuvent entraîner un choc électrique ou un incendie.

Avant chaque utilisation, vérifiez l’état du chargeur, du cordon et de la fiche. Si vous

repérez des dommages, n’utilisez pas le chargeur. N’ouvrez jamais le chargeur vous-

même; apportez-le à un centre de service de l’usine de SKIL ou faites-le réparer avec

des pièces de rechange d’origine par un technicien qualifié. Un réassemblage incorrect

peut entraîner un choc électrique ou un incendie.

Ne touchez pas à la partie non isolée du connecteur de sortie ni à la borne non isolée

de la pile. Un choc électrique pourrait s’ensuivre.

N’utilisez pas d’accessoires qui ne sont pas recommandés ou vendus par SKIL.

L’utilisation d’accessoires non recommandés peut entraîner un choc électrique ou un incendie.

Ne rangez pas le bloc-piles dans son chargeur. Un bloc-piles rangé dans son chargeur

peu, au l du temps, se détériorer et causer un incendie.

Débranchez le chargeur de la prise avant de le ranger ou de procéder à toute tâche

d’entretien ou de nettoyage. De telles mesures de sécurité préventives réduisent le risque

de choc électrique ou d’incendie.

Assurez-vous que le chargeur reste propre en soufflant de l’air comprimé par ses

évents et en essuyant le boîtier à l’aide d’un linge humide. La saleté peut entraîner un

choc électrique ou un incendie.

Remplacez le bloc-piles si vous remarquez une baisse considérable de la durée de

fonctionnement par charge. Il se peut que le bloc-piles ait atteint la n de sa durée de vie

utile.

Lorsqu’un appareil est utilisé en présence d’enfants, une surveillance étroite doit être

exercée afin de réduire les risques de blessure.

N’utilisez pas l’appareil à l’extérieur.

DANGER Les personnes qui portent des dispositifs électroniques, comme un

stimulateur cardiaque, doivent consulter leur médecin avant d’utiliser

le produit. L’utilisation d’équipement électrique à proximité d’un stimulateur cardiaque

peut causer des interférences et l’arrêt du stimulateur.

RALLONGES

AVERTISSEMENT N’UTILISEZ PAS DE RALLONGE ÉLECTRIQUE À MOINS

QUE CELA SOIT ABSOLUMENT NÉCESSAIRE. L’utilisation

d’une rallonge inadaptée peut entraîner un risque d’incendie et de choc électrique. Si vous

utilisez une rallonge électrique, prenez les précautions suivantes :

a. Les broches de la che de la rallonge doivent être identiques en taille et en nombre à celles

de la che du chargeur.

b. La rallonge doit être bien branchée et en bon état.

c. Le calibre de la rallonge doit être sufsant pour l’intensité nominale du chargeur :

Longueur de la rallonge (mètres) 25’ (7.5m) 50’ (15m) 100’ (30.5m) 150’ (45.5m)

Calibre du cordon (AWG) 18 16 16 14

Tableau des rallonges pour les outils de 220 V à 240 V :

CONDUCTEUR de 0,75 mm² 50 Meters

CONDUCTEUR de 1 mm² 75 Meters

d. Une rallonge est une solution temporaire. Branchez le chargeur sur une prise standard dès

que le travail est terminé.

MISE EN GARDE DE LA FCC (COMMISSION FÉDÉRALE DES

COMMUNICATIONS DES ÉTATS-UNIS)

1. Cet appareil est conforme à la partie 15 des règlements de la FCC. Son fonctionnement est

soumis aux deux conditions suivantes :

(1) Cet appareil ne doit provoquer aucune interférence nuisible.

(2) Cet appareil doit accepter toute interférence reçue, y compris des interférences

susceptibles de causer un fonctionnement non désiré.

2. Tout changement ou toute modication non expressément approuvés par la partie

responsable de la conformité peut annuler le droit de l’utilisateur à faire fonctionner l’appareil.

REMARQUE: Cet équipement a été testé et a été déclaré conforme aux restrictions pour

dispositifs numériques de classe B en vertu de la partie 15 des règles de la FCC. Ces

restrictions visent à offrir une protection raisonnable contre l’interférence nuisible d’une

installation résidentielle. Cet équipement génère, utilise et peut émettre de l’énergie de

fréquence radio et, s’il n’est pas installé et utilisé conformément aux instructions, il peut

causer une interférence nuisible aux radiocommunications. Toutefois, il n’est pas garanti

qu’une interférence ne puisse pas se produire dans une installation particulière. Si l’utilisateur

constate des interférences lors de la réception d’émissions de radio ou de télévision (il suft

pour le vérier d’allumer et d’éteindre successivement le dispositif), il devra prendre les

mesures nécessaires pour les éliminer. À cette n, il devra :

• Réorienter ou déplacer l’antenne réceptrice;

• Accroître la distance entre l’appareil et le récepteur;

• Brancher l’article sur une prise de courant appartenant à un autre circuit que celui du

récepteur;

• Obtenir de l’aide auprès du détaillant ou d’un technicien en radio ou en télévision

expérimenté.

SYMBOLES

Symboles de sécurité

L’objectif des symboles de sécurité est d’attirer votre attention sur les dangers potentiels. Vous

devez examiner attentivement et bien comprendre les symboles de sécurité et les explications

qui les accompagnent. Les symboles d’avertissement en tant que tels n’éliminent pas le

danger. Les consignes et les avertissements qui y sont associés ne remplacent en aucun cas

les mesures préventives adéquates.

AVERTISSEMENT Assurez-vous de lire et de comprendre toutes les consignes de

sécurité présentées dans le présent guide d’utilisation,

notamment toutes les consignes de sécurité indiquées par « DANGER »,

« AVERTISSEMENT » et « MISE EN GARDE » avant d’utiliser cet outil. Le fait de ne pas

respecter toutes les consignes de sécurité ci-dessous peut causer un choc électrique, un

incendie ou des blessures graves.

Les dénitions ci-dessous décrivent le degré de gravité pour chaque mot-indicateur. Veuillez lire

ce guide et prêter attention à ces symboles.

Voici le pictogramme d’alerte de sécurité. Il sert à vous indiquer

les risques potentiels de blessures. Respectez toutes les

consignes de sécurité associées à ce pictogramme pour éviter

les risques de blessures ou de mort.

DANGER DANGER indique un danger imminent qui, s’il n’est pas évité,

causera des blessures graves ou la mort.

AVERTISSEMENT AVERTISSEMENT indique un risque pouvant entraîner des

blessures graves ou la mort s’il n’est pas prévenu.

MISE EN GARDE MISE EN GARDE, utilisée avec le symbole d’alerte de

sécurité, indique un risque potentiel qui, s’il n’est pas éliminé,

provoquera des blessures mineures ou moyennement graves.

Messages d’information et de prévention des dommages

Ces messages contiennent des renseignements importants à l’intention de l’utilisateur ainsi

que des consignes à respecter. Le non-respect de celles-ci peut occasionner des dommages

à l’équipement ou d’autres dommages matériels. Chaque message est précédé du mot

« AVIS », comme dans l’exemple ci-dessous :

AVIS : Ne pas suivre ces consignes pourrait occasionner des dommages à l’équipement ou

d’autres dommages matériels.

AVERTISSEMENT L’utilisation de tout outil électrique peut

entraîner la projection de corps étrangers

dans les yeux et ainsi causer des lésions oculaires graves. Lorsque

vous utilisez un outil électrique, portez toujours des lunettes de sécurité

pourvues d’écrans latéraux et d’un écran facial panoramique, au besoin.

Nous recommandons le port d’un masque de sécurité panoramique

par-dessus les lunettes ou de lunettes de sécurité standard avec écrans

latéraux. Portez toujours des protecteurs oculaires conformes à la norme

ANSI Z87.1.

La page est en cours de chargement...

Skil QC5359B-02 Le manuel du propriétaire

Marque: Skil

Modèle: QC5359B-02

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Skil QC5359B-02 Owner's manual
español: Skil QC5359B-02 El manual del propietario

Skil QC5359B-02 Le manuel du propriétaire

Skil QC5359B-02 Le manuel du propriétaire

dans d''autres langues

Documents connexes