DeWalt DWFP55130 Manuel utilisateur

Marque: DeWalt

Modèle: DWFP55130

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, cont_ctenos.

iNSTRUCTiON MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIO Y P©LIZA DE

GARANT[A. ADVERTENClA: LEASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

DWFP55130

Heavy Duty 200 psi Quiet Trim Compressor

Compresseur Silencieux R_sistant De 200 Lb/Po 2Pour Service Intensif

Compresor De Acabado Silencioso De Alta Resistencia De 200 psi

https://manual-hub.com/

Pump/Motor Specifications

Pump:

Motor:

Bore:

Stroke:

Voltage:

Minimum branch circuit requirement:

Fuse Type:

Specifications

MODEL

HEIGHT

WIDTH

LENGTH

AiR TANK CAPACITY (GALLONS)

APPROX CUT=IN PRESSURE

APPROX. CUT=OUT PRESSURE

SCFM @90 PSIG

NOISE LEVEL

REGULATED PRESSURE RATING

(APPROXIMATE)

QUICK CONNECT TYPE

*Tested per ISO 1217

+Tested per ISO 3744

Refer to Glossary for abbreviations.

Maintenance free

Universal

1.875" (47.6 mm)

1.592" (40.4 mm)

Single 120V

15A

Time delay

DWFP55130

20.46" (519.7 mm)

12.66" (321.6 mm)

16.38" (416.1 mm)

2.5 (9.4 liters)

165 psig

200 psig

*3.0

+71.5 dBA

3-150 psi

1/4" (6.4 mm) Industrial

Declared Noise Emission Values

per ISO 3744

Noise Emission Values

Sound Pressure Level (LpA) 71.5 dBA

Sound Pressure Uncertainty (KpA) 3.4 dBA

Sound Power Level (LwA) 84.9 dBA

Sound Power Uncertainty (KwA) 3.4 dBA

The sum of the emission value and the uncertainty is the limit below

which there is a 95% confidence the value of a single tool will lie

below when the tool is new.

https://manual-hub.com/

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

i_,DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

i_WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

_CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

k_ 1

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUTTHIS OR

ANY DEWALTTOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258}

Important Safety Instructions

i_ WARNING: Do not operate this unit until you read this instruction

manual for safety, operation and maintenance instructions.

i_WARNING: This product contains chemicals known to the State

of Califomia to cause cancer, and birth defects or other reproductive

harm. Wash hands after handling.

i_WARNING: Some dust contains chemicals known to the State of

Californiato cause cancer, birth defects or other reproductive harm such

as asbestos and lead inlead based paint.

SAVE THESE INSTRUCTIONS

J_DANGER: RiSK OF EXPLOSION OR FiRE

WHAT CAN HAPPEN HOW TO PREVENT IT

•It is norma/fore/ectrica/ O Always operate the

contacts within the motor compressor in a well ventilated

and pressure switch to area free of Combustible

spark. .materials, gasoline, or solvent

vapors.

if electrical sparks from

compressor come into

contact with flammable

vapors, they may ignite,

causing fire or explosion.

Restncr/ng any of the

compressor ventilation

openings will cause serious

overheating and coulo cause

fire.

•Ifsprayingflammable

materials, locate compressor

at least 20' (6.1 m) away

from spray area. An additional

length of air hose may be

required.

•Store flammable materials in

a secure location away from

compressor

oNever place objects against or

on top of compressor

•Operate compressor in

an open area at least 12"

(30.5 cm) away from any walJ

or obstruction that would

restrict the flow of fresh air to

rne ventilation openings

oOperate compressor in a

clean, dry wel! ventilatea area.

Do not operate unit in an_,

confined area. Store indoors.

https://manual-hub.com/

•Unattended operation of

this product could result in

personal injury or property

damage. Toreduce the

risk of fire, do not allow

the compressor to operate

unattended.

Always remain in attendance

with the product when it is

operating.

Always turn off and unplug

unit when not in use.

_ _ DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN

.The compressed air directly

from your compressor b not

safe for breathing, The air

stream may contain caroon

monoxlae, toxic vapors,

or solid particles from rne

air tank. Breathing these

contaminants can cause

serious injury or death.

•Exoosure TCcnemlcals

GUSTcreaTeooy

cower sanolng, sawing,

gnno/ng, on/ling, ano _ner

cons[ruc[lon ac[iw[les may

be harmful

•Sprayed materials such as

paint, paint solvents, paint

removed insecticides, weed

killers, may contain harmful

vapors and poisons.

HOW TO PREVENT IT

oNever use air obtained directly

from the compressor _osupply

air for human consumption.

The comoressor is not

equipped with suitable filters

and inqine safety equipment

for human consumption.

Work in an area w/[n good

CROSS venTilaTion. Read and

follow the safet_ _ns[mcrlons

omv/oeo on the label or safety

oara sneers for the materials

you are spraying. Always use

certified safety equipment:

NIOSH/OSHA respiratory

protection or properly fitting

face mask designed for use

with your specific application.

_ _ WARNING: RiSK OF BURSTING

Air Tank: On February 26, 2002, the U.S. Consumer Product

Safety Commission published Release # 02-108 concerning air

compressor tank safety:

Air compressor receiver tanks do not have an infinite life. Tank

life is dependent upon several factors, some of which include

operating conditions, ambient conditions, proper installations, field

modifications, and the level of maintenance. The exact effect of

these factors on air receiver life is difficult to predict.

Ifproper maintenance procedures are not followed, internal corrosion

to the inner wall of the air receiver tank can cause the air tank to

unexpectedly rupture allowing pressurized air to suddenly and

forcefully escape, posing risk of injury to consumers.

Your compressor air tank must be removed from service by the end

of the year shown on your tank warning label.

The following conditions could lead to a weakening of the air tank,

and result in a violent air tank explosion:

WHAT CAN HAPPEN HOW TO PREVENT IT

•Faituretoproperlydrain I' Drain airtankdailyorafter

condensed water from Ieach use, !fair tank develops

tank, causing rust ancl a leak, replace it immediately

thinning of the stee! air tank. with a new air tank or replace

the entire compressor

https://manual-hub.com/

•Modifications or attempted •Never drill into, weld, or make

repairs to the air tank. any modifications to the air

tank or its attachments. Never

attempt to repair a damaged

or leaking aY tank. Replace

with a new air tank.

The air tank is designed

to withstand specific

operating pressures, Never

make adjustments or

parts substitutions to alter

the factory set operating

pressures.

ATTACHMENTS & ACCESSORIES:

•Unauthorizedmodifications

to the safety valve or any

other components which

control air tank pressure:

Exceeding the pressure

rating of air tools, spray

guns, air operated

accessories, tires, and other

inflatables can cause them

to explode or fly apart, and

could result in serious injury.

Follow the equipment

manufacturers

recommendation and never

exceed the maximum

allowable pressure rating

of attachments. Never use

compressor to inflate small

low pressure objects such

as children's toys, footballs,

basketballs, etc.

TIRES:

,Over inflation of tires

could result in serious

injury and property

damage.

Use a tire pressure gauge

to check the rites pressure

before each use ano willie

inflating tires."see rne rlre

sidewal! for the correct rlre

pressure.

NOTE: Air tanks, compressors

and similar equipment useo to

inflate tires can fill small tires

very rapidly. Adjust pressure

regulator on air supply ro no

more than the rating of tne

tlre pressure. Add air in small

_ncrements and frequently use

the t_regauge to preven[ over

inflation.

_ A WARNING: RiSK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN IHOW TO PREVENT IT

•Your compressor is powered I" Never operate the compressor

by electricity. Like any other Ioutdoors when it is raining or

electrically powered device, if Iin wet conditions.

it is not used properly it may I_ Never operate compressor

cause electric shock, with protective covers

removed or damaqed.

https://manual-hub.com/

•Repairs attempted by •Any electrical wiring or repairs

unqualified personne/ can required on this product

result in serious injury or should be performed by

death by electrocution, authorized service center

perso ne accordanoewith

national and local electrical

Electrical Grounding:

Failure to provide adequate

grounding to this product

could result in serious injury

or death from electrocution.

Refer to Grounding

Instructions paragraph in

the Installation section.

codes.

•Make certain that the

electrical circuit to which the

compressor is connected

provides proper electrical

grounding, correct voltage and

adequate fuse protection.

_ A WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN

The compressed air stream

can cause soft tissue

damage to exposed skin and

can propel dirt, chips, loose

particles, and smafl objec[s

a[ nigh speed, resulting In

properly damage or persona,

injury.

HOW TO PREVENT IT

.Always wear certified safet_

equipment: ANSI Z87.1 e_e

protection CAN/CSA Z94.3)

with side shields when using

the compresso_

oNever point any nozzle or

sprayer toward any par_ of

the body or at other people or

animals.

•Always turn the compressor

off and bleed pressure

from the al!"nose and a!r

[ank before attempting

maintenance, attaching tools

or accessories.

https://manual-hub.com/

i_ WARNING: RiSK OF HOT SURFACES

HOW TO PREVENT iT

• • Never touch any exposed

metal parts on compressor

during or immediately after

operation. Compressor will

remain hot for several minutes

after operation.

Do not reach around

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

±;D

WHAT CAN HAPPEN

Touching exposed metal

such as the compressor

head, engine head, engine

exhaust or outlet tubes, can

result in serious bums.

WHAT CAN HAPPEN

•Moving parts such as the

RISK FROM MOVING PARTS

HOW TO PREVENT IT

ONever oPerate the comPressor

pulley, flywheel, and belt can with guards or Covers which

cause serious injury if they are damaged or removed.

Come into Contact with you eKeep your hai_ clothing, and

or your clothing, gloves away from moving

parts. Loose clothes, jewelry,

or long hair can be caught in

'moving parts.

Air vents may cover moving

parts and should be avoided

as we!!.

Attempting to operate •Any repairs required on this

compressor with damaged product should be performed

or missing parts or by authorized service center

attempting to repair personnel.

compressor with protective

shrouds removed can

expose you to moving parts

and can result in serious

injury,

_ A WARNING: RISK OF UNSAFE OPERA TION

WHAT CAN HAPPEN HOW TO PREVENT iT

•Unsafe operation of your ,Review and unoersrana al!

compressor could lead 3o instructions and warnings in

serious Injury or death to you rnls manual.

or orners. ,Become fami!iar with th6

operation and controls of tne

air compressor.

®Keep operating area clear

of all persons, pets, and

obstacles.

eKeep children away from _ne

air compressor at al! times.

eDo not operate rne proouc[

when fat/guea or unaer rne

influence of alcohol or drugs.

Stay alert at all times.

https://manual-hub.com/

•Unsafe operation of your _Never defeat the safety

compressor could lead to features of this product.

sen, us injury or death to you ,Equip area of operation wltls a

or orners fcontlnued), fire exrlngutsner

,Do not operate macl_lne

with missing, broken, ol-

unautnonzea parts.

,Never stand on [Re

_ _ WARNING: RiSK OF FALLING

WHAT CAN HAPPEN HOW TO PREVENT iT

•A portable compressor can •Always operate compressor

fall from a table, workbench, in a stable secure position to

or roof causing damage to prevent accidental movement

the compressor and could of the unit. Never operate

result in serious injury or compressor on a roof or

death to the operato_ other elevated position. Use

additional air hose to reach

SAVE THESE INSTRUCTIONS

FOR FUTURE US

COMPONENTS (FIG. 1)

A. On (I)/Off (O)Switch E. Quick Connects

B. Tank Pressure Gauge

C. Regulated Pressure Gauge

D. Pressure Regulator

FIG. 1

C D

F. Safety Valve

G. Air Tank Drain Valve

i_ WARNING: RiSK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

•Under some conditions and oAlways wear proper hearing

duration Of use, noise from protection during use.

this pmduct maY contribute

to hearing loss.

https://manual-hub.com/

FEATURES (FIG. 1)

READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE

OPERATING YOUR UNIT. Compare the illustrationswith your unit

to familiarize yourself with the location of various controls and

adjustments. Save this manual for future reference.

ON(I)/OFF(O) SWITCH

Place this switch (A)in the ON (I)position to provide automatic power

to the pressure switch and OFF (O) to remove power at the end of

each use.

PRESSURE SWITCH (NOT SHOWN}

The pressure switch automatically starts the motor when the air tank

pressure drops below the factory set "cut-in" pressure. It stops the

motor when the air tank pressure reaches the factory set "cut-out"

pressure.

SAFETY VALVE

If the pressure switch does not shut off the air compressor at its

"cut-out" pressure setting, the safety valve (F)will protect against high

pressure by "popping out" at its factory set pressure (slightly higher

than the pressure switch "cut-out" setting).

CHECK VALVE (NOT SHOWN}

When the air compressor is operating, the check valve is "open",

allowing compressed air to enter the air tank. When the air

compressor reaches "cut-out" pressure, the check valve "closes",

allowing air pressure to remain inside the air tank.

TANK PRESSURE GAUGE

The tank pressure gauge (B) indicates the reserve air pressure in

the tank.

REGULATED PRESSURE GAUGE

The regulated pressure gauge (C) indicates the air pressure available

at the outlet side of the regulator. This pressure is controlled by the

regulator.

REGULATOR

The regulator (D) controls the air pressure shown on the outlet

pressure gauge. Turn regulator knob clockwise to increase pressure

and counterclockwise to decrease pressure.

QUICK CONNECT BODIES

The quick connect body (E)accepts industrial quick connect plugs.

The two quick connect bodies allow the use of two tools at the same

time.

DRAIN VALVE

The drain valve (G) is located at the base of the air tank and is used

to drain condensation at the end of each use. See Draining Air

Tank under Maintenance.

COOLING SYSTEM (NOT SHOWN}

This compressor contains an advanced design cooling system. At the

heart of this cooling system is an engineered fan. It is perfectly normal

for this fan to blow air through the vent holes in large amounts. You

know that the cooling system is working when air is being expelled.

AIR COMPRESSOR PUMP (NOT SHOWN}

The pump compresses air into the air tank. Working air is not

available until the compressor has raised the air tank pressure above

that required at the air outlet.

MOTOR OVERLOAD PROTECTOR (NOT SHOWN}

The motor has a thermal overload protector. Ifthe motor overheats for

any reason, the overload protector will shut off the motor. The motor

must be allowed to cool down before restarting. To restart:

https://manual-hub.com/

1.SettheOn/Offswitch(A)toOFFandunplugunit.

2.Allowthemotortocool.

3.Plugthepowercordintothecorrectbranchcircuitreceptacle.

4.SettheOn/OffswitchtoONposition.

DUTY CYCLE (NOT SHOWN}

This air compressor pump is capable of running continuously.

However, to prolong the lifeof your air compressor, it isrecommended

that a 50% average duty cycle be maintained; that is, the air

compressor pump should not run more than 5 minutes in any 10

minute period.

iNSTALLATiON

Grounding instructions (Fig. 2)

AkWARNING: Risk of Electrical Shock. In the event of a short

circuit, grounding reduces the risk of shock by providing an

escape wire for the electric current. This air compressor must

be properly grounded.

The portable air compressor is equipped with a cord having a

grounding wire with an appropriate grounding plug (J).

1. The cord set and plug (J)with this unit FIG.2

contains a grounding pin (L). This

plug MUST be used with a grounded

outlet (K).

IMPORTANT: The outlet being used

must be installed and grounded in

accordance with all local codes and

ordinances.

2. Ensure the outlet being used has the same configuration as the

grounded plug. DO NOT USE AN ADAPTER.

3. Inspect the plug and cord before each use. Do not use if there are

signs of damage.

4. If these grounding instructions are not completely understood, or

if in doubt as to whether the compressor is properly grounded,

have the installation checked by a qualified electrician.

_DANGER: Risk of Electrical Shock. IMPROPER GROUNDING

CAN RESULT IN ELECTRICAL SHOCK.

,Do not modify the plug provided, if #does not fit the

available outlet, a correct outlet should be installed by a

qualified electrician.

•Repairs to the cord set or plug MUST be made by a

qualified electrician.

Extension Cords

If an extension cord must be used, be sure it is:

•a 3-wire extension cord that has a 3-blade grounding plug, and a

3-slot receptacle that will accept the plug on the product

•in good condition

,, no longer than 50' (15.2 m)

,, 14 gauge (AWG) or larger. [Wire size increases as gauge number

decreases. 12 AWG and 10 AWG may also be used. DO NOT

USE 16 OR 18 AWG.)]

NOTICE: Risk of Property Damage. The use of an undersized

extension cord will cause voltage to drop resulting in power loss to the

motor and overheating. Instead of using an extension cord, increase

the working reach of the air hose by attaching another length of hose

to its end. Attach additional lengths of hose as needed.

Voltage and Circuit Protection

Refer to the Voltage and Minimum Branch Circuit Requirements under

Pump/Motor Specifications.

_WARNING: Risk of Overheating. Certain air compressors can be

operated on a 15 amp circuit if the following conditions are met.

•Voltage supply to circuit must comply with the National Electrical

Code.

https://manual-hub.com/

• Circuitisnotusedtosupplyanyotherelectricalneeds.

Extensioncordscomplywithspecifications.

Circuitisequippedwitha 15ampcircuitbreakeror15amp

timedelayfuse.NOTE:Ifcompressorisconnectedtoacircuit

protectedbyfuses,useonlytimedelayfuses.Timedelayfuses

shouldbemarked"D"inCanadaand"T"intheUS.

If any of the above conditions cannot be met, or if operation of the

compressor repeatedly causes interruption of the powec it may be

necessary to operate it from a 20 amp circuit. It is not necessary to

change the cord set.

Location

Locate the air compressor in a clean, dry and well ventilated area.

The air compressor should be located at least 12" (30.5 cm) away

from the wall or other obstructions that will interfere with the flow

of air.

,, The air compressor pump and shroud are designed to allow for

proper cooling. The ventilation openings on the compressor are

necessary to maintain proper operating temperature. Do not place

rags or other containers on or near these openings.

OPERATION

How to Use Your Unit (Fig. 1)

HOW TO STOP

3. Set the On/Off switch (A)to OFF.

2. Unplug unit when not in use.

BEFORE STARTING

i_, WARNING: Do not operate this unit until you read this instruction

manual for safety, operation and maintenance instructions.

BEFORE EACH START=UP

1. Set the On/Off switch (A)to OFF.

2. Plug the power cord into the correct branch circuit receptacle.

(Refer to Voltage and Circuit Protection paragraph in the

Installation section of this manual.)

3. Turn the regulator knob (D) counterclockwise to set the outlet

pressure to zero.

4. Attach hose and accessories.

_WARNING: Risk of unsafe operation. Firmly grasp air hose

in hand when installing or disconnecting to prevent hose whip.

AWARNING: Risk of unsafe operation. Do not use damaged

or worn accessories.

NOTE: The hose or accessory will require a quick connect plug if the

air outlet is equipped with a quick connect body (E).

_, WARNING: Risk of Bursting. Too much air pressure causes

a hazardous risk of bursting. Check the manufacturer's maximum

pressure rating for air tools and accessories. The regulator outlet

pressure must never exceed the maximum pressure rating.

NOTICE: Risk of property damage. Compressed air from the unit

may contain water condensation and oil mist. Do not spray unfiltered

air at an item that could be damaged by moisture. Some air tools and

accessories may require filtered a£ Read the instructions for the air

tools and accessories.

HOW TO START

1. Set the On/Off switch (A)to ON and allow tank pressure to build.

Motor will stop when tank pressure reaches "cut-out" pressure.

2. Turn regulator knob (D) clockwise to increase pressure and stop

when desired pressure is reached.

_WARNING: Risk of unsafe operation. If any unusual noise

or vibration is noticed, stop the compressor immediately and

have ff checked by a trained service technician.

The compressor is ready for use.

https://manual-hub.com/

MAINTENANCE

Customer Responsibilities

Before Daily or See tank

each use after each warning

use label

Check Safety Valve X

Drain Tank X

Remove tank from service X1

1- For more information, call 1-800-4-DEWALT (1-800-433-9258)

h_WARNING: Risk ofunsafe operation. Unit cycles automatically

when power is on. When performing maintenance, you may

be exposed to voltage sources, compressed air, or moving

parts. Personal injuries can occur. Before performing any

maintenance or repair, disconnect power source from the

compressor and bleed off all air pressure.

NOTE: See Operation section for the location of controls.

To Check Safety Valve (Fig. 1)

WARNING: Risk of Bursting. if the safety valve does not

work properly, over-pressurization may occur, causing air tank

rupture or an explosion.

WARNING: Risk from Flying Objects. Always wear certified

safety equipment: ANSI Z87.1 eye protection (CAN/CSA Z94.3)

with side shields.

Before starting compressor, pull the ring on the safety valve (F) to

make sure that the safety valve operates freely. Ifthe valve is stuck or

does not operate smoothly, it must be replaced with the same type

of valve.

To Drain Tank (Fig. 1)

_WARNING: Risk of Unsafe Operation. Air tanks contain high

pressure air. Keep face and other body parts away from outlet

of drain. Use ANSI Z87.1 eye protection (CAN/CSA Z94.3)

when draining as debris can be kicked up into face.

i_ WARNING: Risk from noise. Always wear proper hearing

protection during use. Under some conditions and duration of

use, noise from this product may contribute to hearing loss.

NOTE: All compressed air systems generate condensate that

accumulates in any drain point (e.g., tanks, filter, aftercoolers, dryers).

This condensate contains lubricating oil and/or substances which may

be regulated and must be disposed of in accordance with local, state,

and federal laws and regulations.

/_ WARNING: Risk of Bursting. Water will condense in the air

tank. If not drained, water will corrode and weaken the air tank

causing a risk of air tank rupture.

NOTICE: Risk of Property Damage. Drain water from air tank may

contain oil and rust which can cause stains.

1. Set the On/Off switch (A)to OFF.

2. Turn the regulator knob (D) counterclockwise to set the outlet

pressure to zero.

3. Remove the air tool or accessory.

4. Place a suitable container under the drain valve to catch

discharge.

5. Pull ring on safety valve (F)allowing air to bleed from the tank until

tank pressure is approximately 20 psi. Release safety valve ring.

6. Drain water from air tank by opening drain valve (G)on bottom of

tank.

7. After the water has been drained, close the drain valve. The air

compressor can now be stored.

https://manual-hub.com/

NOTE:Ifdrainvalveisplugged,releaseallairpressure.Thevalvecan

thenberemoved,cleaned,thereinstalled.

STORAG£

Before you store the air compressor, make sure you do the following:

1. Review the Maintenance section on the preceding pages and

perform scheduled maintenance as necessary.

2. Drainwater from air tank. SeeTo Drain Tank under Maintenance.

WARNING: Water will condense in the air tank. If not

drained, water will corrode and weaken the air tank causing a

risk of air tank rupture.

3. Protect the electrical cord and air hose from damage (such as

being stepped on or run over). Wind air hose loosely around the

compressor handle. Wrap electrical cord onto the cord wrap.

4. Store the air compressor in a clean and dry location.

Accessories

J_,WARNING: The use of any other accessory not recommended

for use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the air compresso_

Recommended accessories for use with your tool are available for

purchase from your local dealer or authorized service center. If you

need assistance in locating any accessory for your tool, please contact

DEWALTIndustrial Tool Co., 701 East Joppa Road, Baltimore, MD

21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website

www.dewalt.com.

SERVICE INFORMATION

Please have the following information available for all service calls:

Model Number Serial Number

Date and Place of Purchase

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a DEWALTfactory service

center, a DEWALTauthorized service center or other qualified service

personnel. Always use identical replacement parts.

Thank you for your purchase. Register your product now for:

•WARRANTY SERVICE: Registering your product will help you

obtain more efficient warranty service in case there is a problem

with your product.

•CONFIRMATION OF OWNERSHIP: In case of an insurance

loss, such as fire, flood or theft, your registration of ownership will

serve as your proof of purchase.

•FOR YOUR SAFETY: Registering your product will allow us to

contact you in the unlikely event a safety notification is required

under the Federal Consumer Safety Act.

Full One Year Warranty

DE;iWALTheavy duty industrial tools are warranted for one year from

date of purchase. We will repair, without charge, any defects due to

faulty materials or workmanship. For warranty repair information, call

1-800-4-DEWALT (1-800-433-9258). This warranty does not apply

to accessories or damage caused where repairs have been made or

attempted by others. This warranty gives you specific legal rights and

you may have other rights which vary in certain states or provinces.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

https://manual-hub.com/

FREEWARNINGLABELREPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-DEWALT (1-800-433-

9258) for a free replacement.

GLOSSARY

CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air

delivery.

PS_G: Pounds per square inch gauge; a unit of measure of pressure.

kPa (kHopascal}: Metric pressure measurement. 1 kilopascal equal

1000 pascals.

Code Certification: Products that bear one or more of the following

marks: UL®, CUL, CULUS, ETL®, CETL, CETLUS, have been

evaluated by OSHA certified independent safety laboratories and

meet the applicable Standards for Safety.

*UL®is a registered trademark of Underwriters Laboratories and ETL®

is a registered trademark of Electrical Testing Laboratories.

Out-In Pressure: While the motor is off, air tank pressure drops

when accessory is used. When the tank pressure drops to a certain

low level the motor will restart automatically. The low pressure at

which the motor automatically restarts is called cut-in pressure.

Cut-Out Pressure: When an air compressor is turned on and

begins to run, air pressure in the air tank begins to build. It builds

to a certain high pressure before the motor automatically shuts

off, protecting your air tank from pressure higher than its capacity.

The high pressure at which the motor shuts off is called cut-out

pressure.

Branch Circuit: The circuit carrying electricity from electrical panel

to outlet.

https://manual-hub.com/

Troubleshooting Guide

This section provides a listof the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance

personnel can perform some corrective actions, and others may require the assistance of a qualified DEWALTtechnician or your dealer.

Problem Code

Excessive air tank pressure-safety valve pops off ............................................................................................................................ 3,2

Air leaks .......................................................................................................................................................................................... 3

Air leaks in air tank or at air tank welds ............................................................................................................................................ 4

Air leaks between head and valve plate ........................................................................................................................................... 5

Air leaks from safety valve................................................................................................................................................................ 6

Knocking noise ................................................................................................................................................................................ 6

Pressure reading on the regulated pressure gauge drops when an accessory is used ..................................................................... 7

Compressor is not supplying enough air to operate accessories ............................................................................... 8, 9, 30, 33, 32

Regulator knob has continuous air leak ......................................................................................................................................... 33

Regulator will not shut off air outlet ................................................................................................................................................ 33

Motor will not run .................................................................................................................................. 6, 34, 35, 36, 37, 38, 39, 20

Troubleshooting Codes

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

1 Pressure switch does not shut off Set the Auto!Off switch to OFF,if the Unitdoes not shut off Contact a DEWALT factory service

'motor When Compress0r reaches center or a DEWALTauthorized service Center.

•cut-out pressure

2 Pressure switch cut-out too high Contact a DEWALT factory service center or a DEWALTauthorized service center.

3 Tube fittings are not tight enough Tighten fittings where air can be heard escaPingl Check fittings with soapy water so!ution. Do

• Not Overtighten.

4 Defective air tank Air tank must be replaced. Do not repair the leak.

_,WARNING: Risk of bursting. Do not drill into, weld or otherwise modify air tank or

#will weaken. The air tank can rupture or explode.

5 Leaking seals Contact a DEWALTfactory service center or a DEWALTauthorized service center.

6 Defective safety valve Operate safety valve manually by pulling on ring. Ifvalve still leaks, it must be replaced.

https://manual-hub.com/

CODEPOSSIBLE CAUSE POSSIBLE SOLUTION

7 Regulator is not adjusted Correctly It is normal for some pressure dr0p to occur when an accessory is Used,adjust the regulator

for accessory being used as instrugted in Regulator under Features if pressure drop is excessive.

•NOTE: Adjust the regulated pressure Under flow Conditions While accessory is being Used:

8 Prolonged excessive use of air Decrease amount of air usage.

g Compressor is not large enough for Check the accessory air requirement. If it is higher than the CFM or pressure supplied by your

accessory air compressor, a larger compressor is needed to operate accessory. .........

10 Hole in air hose Replace air hose.

11 Check valve restricted Contact a DEWALTfactory service Center or a DEWALTauthorized service center.

12 Air leaks Tighten fittings.

13 Regulator is damaged Replace:

14 Motor overload protection switch Refer to Motor Overload Protection under Features. If motor overload protection trips

has tripped frequently, contact a DEWALTfactory service center or a DEWALTauthorized service center.

15 Tank pressure exceeds pressure Motor will start automatically when tank pressure drops below cut-in pressure of pressure

switch Cut-in pressure switch.

16 Extension cord is wrong length or Check for proper gauge wire and cord length. Refer to the Extension Cords paragraph in

gauge the Installation section.

17 .Loose electrical Connections Contact a DEWALTfactory Service center or a DEWALTauthorized service center.

18 Possible defective motor Contact a DEWALT factory service center or a DEWALTauthorized service center.

t 9 Paint spray on internal motor parts Contact a DEWALTfactory service center or a DEWALT authorized service center. Do not

• operate the compressor in the paint spray area. See flammable vapor warning:

20 Fuse blown, circuit breaker tripped 1. Check fuse box for blown fuse and replace as necessary. Reset circuit breaker. Do not

use a fuse or circuit breaker with higher rating than that specified for our particular branch

circuit.

2. Check for proper fuse. You should use a time delay fuse.

3. Check for low voltage conditions and/or proper extension cord.

4. Disconnect the other electrical appliances from circuit or operate the compressor on its

own branch circuit.

https://manual-hub.com/

Fiche technique de la pompe/du rnoteur

Pompe:

Moteur:

AI6sage :

Course :

Tension :

Exigence minimale

du circuit de d_rivation :15 A

Type de fusible :temporisation

Fiche technique

MODF:LE

HAUTEUR

LARGEUR

LONGUEUR

CAPACITE DU RESERVOIR D'AIR

(UTRE)

PRESSION D'ENCLENCHEMENT

APPROX.

ENV. PRESSION DE DF:CLENCHEMENT

PIS/MIN STANDARD (SCFM) A90 Ib/po 2

NIVEAU SONORE

Pression nominale stabilisee (approximative)

Type de raccord _ connexion rapide

sans entretien

universel

47,6 mm (1,875 po)

40,4 mm (1,592 po)

monophase, 120V

* Teste conformement _,la norme ISO 1217

+ Teste conformement _,la norme ISO 3744

DWFP55130

519,7 mm (20,46 po)

321,6 mm (12,66 po)

416,1 mm (16,38 po)

9,4 (2,5 gallons)

165 psi

200 psi

"3,0

+71,5 dBA

3-150 psi

Industriel

6,4 mm (1/4")

Refierase al Glosario para descifrar las abreviaturas.

Valeurs de r_rnission de bruits d_clar_es

en conforrnit_ avec riSO 3744

Valeur de I'_mission de bruits

LpA (pression acoustique) 71,5 dBA

KpA (incertitude de la pression acoustique) 3,4 dBA

LwA (puissance acoustique) 84,9 dBA

KwA (incertitude de la puissance acoustique) 3,4 dB(A)

La somme de la valeur de I'emission et de I'incertitude etablit la limite

sous laquelle lavaleur pour un seul outil y sera inferieure et ce, _,95 %

de fiabilite statistique.

https://manual-hub.com/

fD_finitions : lignes directrices en

rnati_re de s_curit_

Les definitions ci-dessous decrivent leniveau de gravite pour chaque

symbole. Veuillez life le mode d'emploi et porter une attention

particuliere a ces symboles.

ADANGER : indique une situation dangereuse imminente qui, si

ellen'est pas evitee, causera la mort ou des blessures graves.

_,AVERTISSEMENT: indique une situation potentie//ement

dangereuse qui, si e//en'est pas evitee, pourra# se solder par un

d_c_s ou des blessures graves.

J_ATTENTION :indique unesituation potentie//ement dangereuse

qui, si e//en'est pas evitee pourra# se solder par des blessures

mineures ou mod_r6es.

AVIS :indique une pratique ne posant aucun risque de

dommages corporels mais qui par contre, si rien n'est fair pour

evitedpourra# poser des risques de dommages mat6riels. J

POUR TOUTES QUESTIONS OU COMMENTAIRES RELATIFS(VES),_,

L'OUTILOU #,PROPOS DETOUT AUTRE OUTILDEWALT,COMPOSER

SANS FRAISLE : 1-800-4-DEWALT (1-800-433-9258}

Directives de s_curit_ impor*antes

AAVERTISSEMENT: ne pas utitiser cot appareil avant d'avoir tu

le mode d'emploi ainsi que I'int_gratit_ des directives de s_curit_,

d'utitisation et d'entretien.

,Z_VERTISSEMENT: ce produit contient des produits chimiques

reconnus par I'Etat de la Califomie comme etant cancerigenes et

pouvant entra[ner des anomalies congenitales ou d'autres problemes

lies aux fonctions reproductrices. Se laver los mains apr_s toute

manipulation.

J_JWERTISSEMENT: certaines poussieres contiennent des

produits chimiques reconnus par I'Etat de la Califomie comme

cancerigenes et pouvant entra?ner des anomalies congenitales

et d'autres problemes lies aux fonctions reproductrices, tels que

I'amiante et le plomb contenus clans los peintures au plomb.

CONSERVER C£S DIR£CTIVES

J_ DANGER: RISQUE D'EXPLOSION OU

D'INCENDIE

CE QUI PEUT SE

PRODUIRE

,, II est normal que des

contacts _lectriques

dans le moteur et le

manocontacteur fassent

une etincelle.

Si une etincelle dectrique

provenant du compresseur

entre en contact avec des

vapeurs inflammables,

ellepout s'enflammer et

causer un incendie ou une

explosion.

COMMENT L'i'-=VITER

oFaites toujours fonctionner

compresseurdans une

zone bien a6r_e sans matiere

combustible, essenc e ou

vapeur de so/rant.

•Si vous aspergez des

materiaux inflammables,

placez le compresseur

au moins 6,1 m(20 plods)

de la zone pulverisee. IIest

possible que vous ayez besoin

d'une Iongueur de tuyau

additionnelle.

•Entreposez los matieres

inflammables clans un

endroit securitaire, doigne du

compresseu_

https://manual-hub.com/

Le fait de limiter les

ouver_ures d'a_ration de

compresseur causera une

/mpor_ante surchauffe

e[pourralt causer UR

incendie.

L_efonctionnement ae ce

produit sans surveillance

pourrait se solder par des

blessures personnelles

ou des dommages a la

pmpriete. Afin de reduire

le risque d'incendie, ne

pas laisser le compresseur

fonctionner sans

surveillance.

oNe placezjamais des objers

contre le compresseur ou sur

celui-ci.

Faites fonctlonner le

compresseur OaRSun endroft

aere _au moins 30.5 cm

(12 po) ou mur oc de

/'obstruction qu_pourra/t I/mlter

le debit d'air frais clans les

ouvemlres d'a_ration.

=Faites fonctionner le

compresseur clans un enoroit

propre, sec et bien aere. Ne

pas utiliser I'appare!l a clans

un endrott exigu. Macjasin

I'interieur

•Etre toujours presen_ iorsclue e

produit esten mamhe.

Toujours eteindre et

debrancher I'appareil si non

utilise.

J_ DANGER: RISQUE REPIRATOIRE (ASPNYXIE)

CE QUI PEUT SE

PRODUIRE

•IIest dangereuxde respirer

/'air comprime sortant du

compresseur Le flux d'air

peut contenir du moooxyde

de carbone, des vapeurs

toxiques ou des particules

sondes provenant du

reservoir d'air La respiration

ces contaminants

COMMENT L'C:VITER

®Nejamais utiliserl'air obtenu

directement du compresseur

pour l:alimentation en air

destinee _la consommation

hurnaine. Le compresseur

ntest pas muni de filtres et

d:4quipernent de securite

en ligne qui conviennent a la

consommation humaine.

peut Causer de s_rieuses ,

blessures, voire la mort.

Une exposition aux produits

chimiques presents dons

la poussiere generee par

les activites de ponqage,

sciage, meulage, perqage

et autres, peut 6tre nocive.

Les materiaux vaporises

comme la peinture, les

solvants de peinture, les

decapants, les insecticides,

les herbicides, pourraient

contenir des vapeurs

nocives et du poison.

Travaillerdons un endroit

ayant une bonne aeration

transversale. Life et respecter

les directives en matiere

de securite imprimees sur

I'etiquette ou les fiches

signaletiques des materiaux qui

soRt pulverises. Toujours utiliser

un equipement de securite

homologue : une protection

respiratoire conforme aux

normes NIOSH/OSHA, ou

un masque facial bieR ajuste,

conqus specifiquement pour

votre utilisation particuliere.

https://manual-hub.com/

AAVERTISSEMENT: RISQUE D'L-CLATEMENT

R6servoir d'air comprim6 : Le 26 fevrier 2002, la U.S. Consumer

Product Safety Commission americaine a publie la regle n° 02-108

portant sur la securite en matiere de reservoir d'air comprime des

compresseurs :

Les reservoirs d'air comprime des compresseurs n'ont pas une

duree de vie illimitee. La duree de vie des reservoirs depend de

plusieurs facteurs, qui comprennent entre autres : les conditions

d'utilisation, les conditions ambiantes, une installation adequate, les

modifications sur site, et le niveau de maintenance. L'effet exact que

peut avoir ces facteurs sur la duree de vie des reservoirs d'air est

difficilement previsible.

Si les procedures adequates de maintenance ne sont pas suivies,

la corrosion sur la paroi interne du reservoir d'air comprime peut

faire que celui-ci eclate de fagon inopinee laissant soudainement

I'air pressurise s'echapper avec force, posant ainsi des risques de

dommages corporels _.I'utilisateur.

Le reservoir d'air de votre compresseur doit 6tre mis hors service _.

la fin de I'annee mentionnee sur I'etiquette d'avertissement apposee

sur le reservoir.

Les conditions suivantes peuvent amener la degradation du

reservoir d'air, et faire que ce dernier explose violemment :

CE QUI PEUT SE

PRODUIRE

•L'eau condensee n'est pas

correctement vidang_e du

reservoir d'air provoquant

ainsi la formation de rouille

et un amincissement du

COMMENT L'i'-=VITER

Vidanger le reservoir dWr

quotidiennement ou apres

chaque uti!isation. Si le

reservoir presente une fuite, le

remplacer immediatement pat"

reserv°irdla<en ier I unnouveaureservoird{airou

par un nouveau compresseur

•Modifications apportees au •Ne jamais percer un tmu

reservoir d'air ou tentatives clans le reservoir d'air ou

de reparation, ses accessoires, y loire de la

soudure ou y apporter quelque

modification que ce soit. Ne

jamais essayer de reparer un

reservoir d'air endommage ou

avec des fuites. Le remplacer

par un nouveau reservoir d'ai_

•Des modifications non oLe reservoir d;air a 4t_ Congu

autorisees de la soupape pour supporter des pressions

de sOrete ou de tous specifiques de fonctionnement,

autres Composants qui Ne faites jamais efectuer de

regissent la pression du r#glages ou de substitutions de

reservolr d a!!'. pieces en rue de modlfler les

pressions de fonctionnement

regimes en usine.

https://manual-hub.com/

La page charge ...

DeWalt DWFP55130 Manuel utilisateur

Marque: DeWalt

Modèle: DWFP55130

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DWFP55130 User manual
español: DeWalt DWFP55130 Manual de usuario

DeWalt DWFP55130 Manuel utilisateur

DeWalt DWFP55130 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents