LG Electronics LCWB-002 WiFi/BLE + MCU Module Manuel utilisateur

LG Electronics
Marque
LG Electronics
Modèle
LCWB-002 WiFi/BLE + MCU Module
Taper
Manuel utilisateur
User manual
PRODUCT NAME : Wi-Fi / BLE + MCU Module
MODEL NAME : LCWB-002
The information contained herein is the exclusive property of LG and shall
not be distributed, reproduced or disclosed in whole or no in part without
prior written permission of LG.
H/W version : V1.0
S/W version : V1.0
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
2 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
Table of Contents
No Description Page
1 Features 3
2 Block Diagram 3
3 Absolute Maximum Ratings 4
4 Operating Test Conditions 4
5 Electrical Characteristics 5
6 Pin Description 9
7 Outline Drawing 10
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
3 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
1. Features
LCWB-002 is the module for IEEE 802.11b/g/n wireless LAN + BLE4.2 + MCU.
LCWB-002 is based on Realtek RTL8720CM solution.
IEEE 802.11 b/g/n HT20 single band WLAN infra-structure
Bluetooth Low Energy 4.2 (BLE4.2)
Size : 20 mm x 45 mm x 7.9 mm
Auto-calibration (RF, Crystal)
Data rates up to 72.2Mbps PHY rate
SPI interface
Integrated IPv4/IPv6 TCP/IP stack
Integrated Network services such as HTTP, DNS, FTP
Security : WFA, WPA, WPA2, WEP, WAPI, TKIP
Application : Home Appliance
2. Block Diagram
RTL8720CM
Interface
Block
MCU
(Real M300)
Clock (40MHz)
ANT
ROM 384KB
DC-DC converter 5V / 12V
3.3V
802.11 b/g/n
BLE4.2
MAC/BB Flash
Memory
(8MB)
RAM 256KB PMU
SPI
JTAG
LDO
3.3V1.8V
pSRAM 4MB
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
4 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
Parameter Min Max Unit
Storage Temperature -40 +100 ℃
Storage Humidity (@ 40℃)-90 %
Caution : The specifications above the Table define levels at which permanent damage
to the device can occur. Function operation is not guaranteed under these conditions.
Operating at absolute maximum conditions for extend periods can adversely affect the
long-term reliability of the device.
•Other conditions
1) Do not use or store modules in the corrosive atmosphere, especially where chloride
gas, sulfide gas, acid, alkali, salt or the like are contained
Also, avoid exposure to moisture
2) Store the modules where the temperature
and relative humidity do not exceed 5 to 40℃and 20 to 60%
3) Assemble the modules within 6 months
Check the soldering ability in case of 6 months over
3. Absolute Maximum Ratings
Parameter Min Typ Max Unit
Operating Temperature 0 - +85 ℃
Operating Humidity (40℃)- - 85 %
Supply Voltage 4.5 5.0 5.5 Vdc
10.8 12 13.2
4. Operating Test Conditions
1) Test condition : AP connection Ping test mode(not continuous Tx and T-Put mode)
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
5 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
Items Contents
Specification IEEE802.11b
Mode DSSS / CCK
Channel frequency 2400 ~ 2483MHz
Data rate 1, 2, 5.5, 11Mbps
TX Characteristics Min. Typ. Max. Unit
Power Level 14 17 20 dBm
Spectrum Mask
1st side lobes ( to fc ±11MHz) - - -30 dBr
2nd side lobes ( to fc ±22MHz) - - -50 dBr
Modulation Accuracy (EVM) - - 35 %
Power On/Off ramp - - 2.0 usec
Freq. Tolerance -25 -25 ppm
Chip Clock Freq. Tolerance -25 -25 ppm
RX Characteristics Min. Typ. Max. Unit
Minimum Input Level Sens. (FER ≤ 8%) - - -76 dBm
Maximum Input Level (FER ≤ 8%) -10 - - dBm
5. Electrical Characteristics
5-1. RF Characteristics for IEEE802.11b (11Mbps mode unless otherwise specified)
* Normal Condition : 25℃, VDD=5V.
* RF characteristics is board limit. It can differ according to standards
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
6 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
Items Contents
Specification IEEE802.11g
Mode OFDM
Channel frequency 2400 ~ 2483MHz
Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps
TX Characteristics Min. Typ. Max. Unit
Power Level 12 15 18 dBm
Spectrum Mask
at fc ±11MHz - - -20 dBr
at fc ±20MHz - - -28 dBr
at fc ≥ ±30MHz - - -40 dBr
Constellation Error (EVM) - - -25 dB
Freq. Tolerance -20 -20 ppm
Chip Clock Freq. Tolerance -20 -20 ppm
RX Characteristics Min. Typ. Max. Unit
Minimum Input Level Sens. (PER ≤ 10%) - - -65 dBm
Maximum Input Level (PER ≤ 10%) -20 - - dBm
5-2. RF Characteristics for IEEE802.11g (54Mbps mode unless otherwise specified)
* Normal Condition : 25℃, VDD=5V.
* RF characteristics is board limit. It can differ according to standards
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
7 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
5-3. RF Characteristics for IEEE802.11gn (MCS7 mode unless otherwise specified)
* Normal Condition : 25℃, VDD=5V.
* RF characteristics is board limit. It can differ according to standards
Items Contents
Specification IEEE802.11n –2.4GHz
Mode OFDM
Channel frequency 2400 ~ 2483MHz
Data rate 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps
TX Characteristics Min. Typ. Max. Unit
Power Level (HT20 : MCS7) 11 14 17 dBm
Spectrum Mask (HT20)
at fc ±11MHz - - -20 dBr
at fc ±20MHz - - -28 dBr
at fc ±30MHz - - -40 dBr
Constellation Error (EVM) - - -28 dB
Freq. Tolerance -20 -20 ppm
Chip Clock Freq. Tolerance -20 -20 ppm
RX Characteristics Min. Typ. Max. Unit
Minimum Input Level Sens.
(HT20,PER ≤ 10%) - - -64 dBm
Maximum Input Level (PER ≤ 10%) -20 - - dBm
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
8 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
5-4. RF Characteristics for BLE
* Normal Condition : 25℃, VDD=5V.
* RF characteristics is board limit. It can differ according to standards
TX characteristics Min. Typ. Max. Unit
Power level 1.5 4.5 7.5 dBm
Adjacent channel transmit power
@ F = F0 ±1MHz - - 0 dBr
@ F = F0 ±2MHz - - -30 dBr
@ F = F0 ±3MHz - - -40 dBr
@ F > F0 ±3MHz - - -40 dBr
Modulation characteristics –Frequency derivation
ΔF1AVG 140 -175 KHz
ΔF2MAX 115 - - KHz
ΔF2MAX / ΔF1AVG 80 - - %
RX characteristics Min. Typ. Max. Unit
Min. input level (BER ≤ 0.1%) - - -84 dBm
Max. input level (BER ≤ 0.1%) -20 - - dBm
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
9 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
6. Pin Description
Pin No. Pin Name
1VDD
2 MODE
3 SPI_SCL
4 SPI_CSN
5 SPI_MISO
6 SPI_MOSI
7 STATUS
8 GND
< Top side > < Bottom side >
< Top side >
①
⑧
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
10 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
7. Outline Drawing
Kap soul Lee
'21. 06. 22
Jae kil Jung
Seok dong Choi
'21. 06. 22
'21. 06. 22
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
11 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
Regulatory Notice
Part 15.19 Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Part 15.105 Statement (Class B)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:- Reorient or relocate the
receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Part 15.21 Statement
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. This device
must not be co-located or operating in conjunction with any other antenna or
transmitter.
Responsible Party Information (Supplier's Declaration of Conformity)
LG Electronics USA1000 Sylvan Avenue Englewood Cliffs New Jersey, United
States, 07632
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
12 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
Regulatory Notice
Regulatory notice to host manufacturer according to KDB 996369 D03 OEM
Manual
List of applicable FCC rules
This module has been granted modular approval as below listed FCC rule parts. -
FCC Rule parts 15C(15.247)
Summarize the specific operational use conditions
The OEM integrator should use equivalent antennas which is the same type and
equal or less gain then an antenna listed in this instruction manual.
RF exposure considerations
The module has been certified for integration into products only by OEM integrators
under the following condition:
-The antenna(s) must be installed such that a minimum separation distance of at
least 20 cm is maintained between the radiator (antenna) and all persons at all times.
-The transmitter module must not be co-located or operating in conjunction with any
other antenna or transmitter except in accordance with FCC multi-transmitter
product procedures.
-Mobile use
As long as the three conditions above are met, further transmitter testing will not be
required.OEM integrators should provide the minimum separation distance to end
users in their end-product manuals.
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
13 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
Regulatory Notice
Antennas list
This module is certified with the following integrated antenna.
-Type: Printed Antenna
- Max. peak Antenna gain: 1.58 dBi
Any new antenna type, higher gain than listed antenna should be met the
requirements of FCC rule 15.203 and 2.1043 as permissive change procedure.
Label and compliance information
End Product Labeling
The module is labeled with its own FCC ID. If the FCC ID is not visible when the
module is installed inside another device, then the outside of the device into which
the module is installed must also display a label referring to the enclosed module. In
that case, the final end product must be labeled in a visible area with the following:
Contains FCC ID: BEJ-LCWB002
Information on test modes and additional testing requirements
OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed (for example, digital
device emissions, PC peripheral requirements, additional transmitter in the host,
etc.).
Additional testing, Part 15 Subpart B disclaimer
The final host product also requires Part 15 subpart B compliance testing with the
modular transmitter installed to be properly authorized for operation as a Part 15
digital device.
USER MANUAL
PAGE :
REG. DATE : 2021. 07. 07
MODEL NAME : LCWB-002
REV. NO : v1.0
14 / 10
REV. DATE : 2021. 07. 07
LG Innotek Confidential : This document is protected by security policies and laws.
[Restricted]
Regulatory Notice (ISED)
RSS-GEN, Sec. 7.1.3–(licence-exempt radio apparatus)
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:(1) this device may not cause
interference, and(2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
RF Exposure
The antenna (or antennas) must be installed so as to maintain at all times a distance
minimum of at least 20 cm between the radiation source (antenna) and any
individual. This device may not be installed or used in conjunction with any other
antenna or transmitter.
l'exposition aux RFL’antenne (ou les antennes) doit être installée de façon à
maintenir à tout instant une distance minimum de au moins 20 cm entre la source de
radiation (l’antenne) et toute personne physique.
End Product Labeling
The module is labeled with its own IC Certification Number. If the IC Certification
Number is not visible when the module is installed inside another device, then the
outside of the device into which the module is installed must also display a label
referring to the enclosed module. In that case, the final end product must be labeled
in a visible area with the following:
Contains IC: 2703N-LCWB002
É tiquetage du produit final (IC)
Le module est étiqueté avec son propre numéro de certification IC. Si le numéro de
certification IC n'est pas visible lorsque le module est installé à l'intérieur d'un autre
appareil, l'extérieur de l'appareil dans lequel le module est installé doit également
afficher une étiquette faisant référence au module fourni. Dans ce cas, le produit
final doit être étiqueté dans une zone visible avec ce qui suit :
Contient module émetteur IC : 2703N-LCWB-002
Le module est étiqueté avec son propre numéro de certification IC. Si le numéro de certification IC n'est pas visible lorsque
Le module est étiqueté avec son propre numéro de certification IC. Si le numéro de certification IC n'est pas visible lorsque
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

LG Electronics LCWB-002 WiFi/BLE + MCU Module Manuel utilisateur

LG Electronics
Marque
LG Electronics
Modèle
LCWB-002 WiFi/BLE + MCU Module
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents