LG LCWB-001 Wi-Fi BLE + MCU Modul Manuel utilisateur

Marque: LG

Modèle: LCWB-001 Wi-Fi BLE + MCU Modul

Taper: Manuel utilisateur

User manual

PRODUCT NAME : Wi-Fi / BLE + MCU Module

MODEL NAME : LCWB-001

The information contained herein is the exclusive property of LG and shall

not be distributed, reproduced or disclosed in whole or no in part without

prior written permission of LG.

Secret Level 2

H/W version : V1.0

S/W version : V1.0

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

2 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

Table of Contents

No Description Page

1 Features 3

2 Block Diagram 3

3 Absolute Maximum Ratings 4

4 Operating Test Conditions 4

5 Electrical Characteristics 5

6 Pin Description 9

7 Outline Drawing 10

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

3 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

1. Features

LCWB-001 is the module for IEEE 802.11b/g/n wireless LAN + BLE4.2 + MCU.

LCWB-001 is based on Realtek RTL8720CM solution.

IEEE 802.11 b/g/n HT20 single band WLAN infra-structure

Bluetooth Low Energy 4.2 (BLE4.2)

Size : 20 mm x 48 mm x 11.4 mm

Auto-calibration (RF, Crystal)

Data rates up to 72.2Mbps PHY rate

UART interface

Integrated IPv4/IPv6 TCP/IP stack

Integrated Network services such as HTTP, DNS, FTP

Security : WFA, WPA, WPA2, WEP, WAPI, TKIP

Application : Home Appliance

2. Block Diagram

RTL8720CM

Interface

Block

MCU

(Real M300)

Clock (40MHz)

ANT

ROM 384KB

DC-DC converter 5V / 12V

3.3V

802.11 b/g/n

BLE4.2

MAC/BB Flash

Memory

(8MB)

RAM 256KB PMU

UART

JTAG

LDO

3.3V1.8V

pSRAM 4MB

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

4 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

Parameter Min Max Unit

Storage Temperature -40 +100 ℃

Storage Humidity (@ 40℃) - 90 %

Caution : The specifications above the Table define levels at which permanent damage

to the device can occur. Function operation is not guaranteed under these conditions.

Operating at absolute maximum conditions for extend periods can adversely affect the

long-term reliability of the device.

•Other conditions

1) Do not use or store modules in the corrosive atmosphere, especially where chloride

gas, sulfide gas, acid, alkali, salt or the like are contained

Also, avoid exposure to moisture

2) Store the modules where the temperature

and relative humidity do not exceed 5 to 40℃and 20 to 60%

3) Assemble the modules within 6 months

Check the soldering ability in case of 6 months over

3. Absolute Maximum Ratings

Parameter Min Typ Max Unit

Operating Temperature 0 - +85 ℃

Operating Humidity (40℃)- - 85 %

Supply Voltage 4.5 5.0 5.5 Vdc

10.8 12 13.2

4. Operating Test Conditions

1) Test condition : AP connection Ping test mode(not continuous Tx and T-Put mode)

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

5 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

Items Contents

Specification IEEE802.11b

Mode DSSS / CCK

Channel frequency 2400 ~ 2483MHz

Data rate 1, 2, 5.5, 11Mbps

TX Characteristics Min. Typ. Max. Unit

Power Level(Average) 14 17 20 dBm

Spectrum Mask

1st side lobes ( to fc ±11MHz) - - -30 dBr

2nd side lobes ( to fc ±22MHz) - - -50 dBr

Modulation Accuracy (EVM) - - 35 %

Power On/Off ramp - - 2.0 usec

Freq. Tolerance -25 -25 ppm

Chip Clock Freq. Tolerance -25 -25 ppm

RX Characteristics Min. Typ. Max. Unit

Minimum Input Level Sens. (FER ≤ 8%) - - -76 dBm

Maximum Input Level (FER ≤ 8%) -10 - - dBm

5. Electrical Characteristics

5-1. RF Characteristics for IEEE802.11b (11Mbps mode unless otherwise specified)

* Normal Condition : 25℃, VDD=5V.

* RF characteristics is board limit. It can differ according to standards

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

6 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

Items Contents

Specification IEEE802.11g

Mode OFDM

Channel frequency 2400 ~ 2483MHz

Data rate 6, 9, 12, 18, 24, 36, 48, 54Mbps

TX Characteristics Min. Typ. Max. Unit

Power Level(Average) 12 15 18 dBm

Spectrum Mask

at fc ±11MHz - - -20 dBr

at fc ±20MHz - - -28 dBr

at fc ≥ ±30MHz - - -40 dBr

Constellation Error (EVM) - - -25 dB

Freq. Tolerance -20 -20 ppm

Chip Clock Freq. Tolerance -20 -20 ppm

RX Characteristics Min. Typ. Max. Unit

Minimum Input Level Sens. (PER ≤ 10%) - - -65 dBm

Maximum Input Level (PER ≤ 10%) -20 - - dBm

5-2. RF Characteristics for IEEE802.11g (54Mbps mode unless otherwise specified)

* Normal Condition : 25℃, VDD=5V.

* RF characteristics is board limit. It can differ according to standards

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

7 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

5-3. RF Characteristics for IEEE802.11gn (MCS7 mode unless otherwise specified)

* Normal Condition : 25℃, VDD=5V.

* RF characteristics is board limit. It can differ according to standards

Items Contents

Specification IEEE802.11n –2.4GHz

Mode OFDM

Channel frequency 2400 ~ 2483MHz

Data rate 6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps

TX Characteristics Min. Typ. Max. Unit

Power Level(Average)(HT20 : MCS7) 11 14 17 dBm

Spectrum Mask (HT20)

at fc ±11MHz - - -20 dBr

at fc ±20MHz - - -28 dBr

at fc ±30MHz - - -40 dBr

Constellation Error (EVM) - - -28 dB

Freq. Tolerance -20 -20 ppm

Chip Clock Freq. Tolerance -20 -20 ppm

RX Characteristics Min. Typ. Max. Unit

Minimum Input Level Sens.

(HT20,PER ≤ 10%) - - -64 dBm

Maximum Input Level (PER ≤ 10%) -20 - - dBm

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

8 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

5-4. RF Characteristics for BLE

* Normal Condition : 25℃, VDD=5V.

* RF characteristics is board limit. It can differ according to standards

TX characteristics Min. Typ. Max. Unit

Power Level(Average) 1.5 4.5 7.5 dBm

Adjacent channel transmit power

@ F = F0 ±1MHz - - 0 dBr

@ F = F0 ±2MHz - - -30 dBr

@ F = F0 ±3MHz - - -40 dBr

@ F > F0 ±3MHz - - -40 dBr

Modulation characteristics –Frequency derivation

ΔF1AVG 140 -175 KHz

ΔF2MAX 115 - - KHz

ΔF2MAX / ΔF1AVG 80 - - %

RX characteristics Min. Typ. Max. Unit

Min. input level (BER ≤ 0.1%) - - -84 dBm

Max. input level (BER ≤ 0.1%) -20 - - dBm

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

9 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

6. Pin Description

Pin No. Pin Name I/O Pin Description

1VDD I VDD (5V, 12V)

2 UART Rx I UART Communication signal line

3NC -NC

4NC -NC

5 UART Tx O UART Communication signal line

6 GND - GND

< Top side > < Bottom side >

①

⑥

Note.

1) Recommend a module install sequence for prevent UART device failure

- Supply 5V, 12V power

- Connect to data signal (UART Tx, UART Rx)

2) Recommend to use the shielding cable

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

10 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

7. Outline Drawing

'20. 07. 10

Kapsoul Lee.

'20. 07. 10

Je hyuk Moon

Seokdong Choi

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

11 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

Regulation Notice

1. FCC Statement

FCC Part 15.19 Statements:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

FCC Part 15.21 statement

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

Responsible Party Information

Supplier's Declaration of Conformity

47 CFR §2.1077 Compliance

InformationResponsible Party –U.S. Contact Information

LG Electronics USA1000 Sylvan Avenue Englewood Cliffs

New Jersey, United States, 07632

Telephone number or internet contact information

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

12 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

Regulation Notice

2. Regulatory notice to host manufacturer according to KDB 996369 D03 OEM

Manual v01

List of applicable FCC rules

This module has been granted modular approval as below listed FCC rule parts.

- FCC Rule parts 15C(15.247)

Summarize the specific operational use conditions

The OEM integrator should use equivalent antennas which is the same type and equal

or less gain then an antenna listed in this instruction manual.

RF exposure considerations

The module has been certified for integration into products only by OEM integrators

under the following condition:

-The antenna(s) must be installed such that a minimum separation distance of at least

20 cm is maintained between the radiator (antenna) and all persons at all times.

-The transmitter module must not be co-located or operating in conjunction with any

other antenna or transmitter except in accordance with FCC multi-transmitter product

procedures.

-Mobile use

As long as the three conditions above are met, further transmitter testing will not be

required.

OEM integrators should provide the minimum separation distance to end users in their

end-product manuals.

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

13 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

Regulation Notice

Antennas list

This module is certified with the following integrated antenna.

-Type: PCB Pattern Antenna

-Max. peak Antenna gain

Frequency Antenna gain

BT LE 2402 ~ 2480 MHz 1.5 dBi

Wi-Fi 2412 ~ 2462 MHz 1.5 dBi

Any new antenna type, higher gain than listed antenna should be met the requirements

of FCC rule 15.203 and 2.1043 as permissive change procedure.

Label and compliance information

End Product Labeling

The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID

and IC Certification Number are not visible when the module is installed inside another

device, then the outside of the device into which the module is installed must also

display a label referring to the enclosed module. In that case, the final end product must

be labeled in a visible area with the following:

Contains FCC ID: BEJ-LCWB001

Contains IC: 2703N-LCWB001

Information on test modes and additional testing requirements

OEM integrator is still responsible for testing their end-product for any additional

compliance requirements required with this module installed (for example, digital device

emissions, PC peripheral requirements, additional transmitter in the host, etc.).

Additional testing, Part 15 Subpart B disclaimer

The final host product also requires Part 15 subpart B compliance testing with the

modular transmitter installed to be properly authorized for operation as a Part 15 digital

device.

USER MANUAL

PAGE :

REG. DATE : 2020. 07. 21

MODEL NAME : LCWB-001

REV. NO : v100

14 / 10

REV. DATE : 2020. 07. 21

Secret Level 2

Regulation Notice

3. ISED Statement

RSS-GEN, Sec. 7.1.3–(licence-exempt radio apparatus)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation

is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils

radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

RF Exposure

The antenna (or antennas) must be installed so as to maintain at all times a distance

minimum of at least 20 cm between the radiation source (antenna) and any individual.

This device may not be installed or used in conjunction with any other antenna or

transmitter.

l'exposition aux RF

L’antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une

distance minimum de au moins 20 cm entre la source de radiation (l’antenne)et toute

personne physique.

Caution: Any changes or modifications to this device not explicitly approved by

manufacturer could void your authority to operate this equipment. Attention:

Les changements ou modifications de cet appareil non expressément approuvé par le

fabricant peuvent annuler votre droit à utiliser cet équipement.

Étiquetage du produit final (IC)

Le module LCWB-001 est étiqueté avec sa propre identification FCC et son propre

numéro de certification IC.Si l’identification FCC et le numéro de certification IC ne sont

pas visibles lorsque le module est installé à l’intérieur d’un autre dispositif, la partie

externe du dispositif dans lequel le module est installé devra également présenter une

étiquette faisant référence au module inclus. Dans ce cas, le produit final devra être

étiqueté sur une zone visible avec les informations suivantes :

Contient module émetteur identification FCC ID:BEJ-LCWB001

Contient module émetteur IC :2703N-LCWB001

LG LCWB-001 Wi-Fi BLE + MCU Modul Manuel utilisateur

Marque: LG

Modèle: LCWB-001 Wi-Fi BLE + MCU Modul

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: LG LCWB-001 Wi-Fi BLE + MCU Modul User manual

LG LCWB-001 Wi-Fi BLE + MCU Modul Manuel utilisateur

LG LCWB-001 Wi-Fi BLE + MCU Modul Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents