Kichler 300044 Manuel utilisateur

Product images may vary slightly from actual product.

56”/ 48” Brahm LED

INSTRUCTION MANUAL

Model# 300044, 300048

READ AND SAVE THESE INSTRUCTIONS

SAFETY RULES…………………………………………………………………….....3

TOOLS REQUIRED………………………………………………………………….5

PACKAGE CONTENTS……………………………………………………………5

MOUNTING OPTIONS……………………………………………………………6

HANGING THE FAN………………………………………………………………...7

INSTALLATION OF SAFETY SUPPORT……………………………….9

ELECTRICAL CONNECTIONS……………………………………………..10

FINISHING THE MOTOR INSTALLATION……………………………...11

ATTACHING THE FAN BLADES……………………………………………...12

INSTALLING THE SWITCH HOUSING……………………………………13

INSTALLING THE LIGHT KIT AND GLASS……………………………..14

INSTALLING THE COOLTOUCH CONTROL

SYSTEM WALL PLATE……………………………………………………………..15

INSTALLING AND REMOVING THE HANDHELD

TRANSMITTER………………………………………………………………………....16

OPERATING INSTRUCTIONS…………………………………………………16

REVERSE FUNCTION………………………………………………………………18

FCC INFORMATION…………………………………………………………………18

TROUBLESHOOTING………………………………………………………………19

TABLE OF CONTENTS

2 | KICHLER.COM

SAFETY RULES

CAUTION – RISK OF SHOCK – Disconnect Power at

the main circuit breaker panel or main fusebox before

starting and during the installation.

WARNING: All wiring must be in accordance with the

National Electrical Code “ANSI/NFPA 70” and local

electrical codes. Electrical installation should be

performed by a qualified licensed electrician.

WARNING: To reduce the risk of electric shock, this fan

must be installed with a general-use, isolating wall

control/switch.

WARNING: Not suitable for use with solid-state speed

controls.

WARNING: Chemical Burn Hazard. Keep batteries

away from children.; andThis product contains a

lithium button/coin cellbattery. If a new or used lithium

button/coin cellbattery is swallowed or enters the

body, it can causesevere internal burns and can lead to

death in as littleas 2 hours. Always completely secure

the batterycompartment. If the batterycompartment

does notclose securely, stop using the product,

1.

2.

3.

4.

5.

remove thebatteries, and keep it away from children. If

you thinkbatteries might have been swallowed or

placed insideany part of the body, seek immediate

medical attention.

a) The cells shall be disposed of properly,

includingkeeping them away from children; and

b) Even used cells may cause injury.

WARNING: To reduce the risk of fire, electric shock, or

personal injury, mount to outlet box marked

“acceptable for fan support of 15.9 kg (35 lbs.) or less”

and use mounting screws provided with the outlet box.

Most outlet boxes commonly used for the support of

light fixtures are not acceptable for fan support and

may need to be replaced. Due to the complexity of the

installation of this fan, a qualified licensed electrician is

strongly recommended.

The outlet box and support structure must be securely

mounted and capable of reliably supporting a minimum of

15.9 kg (35 pounds). Use only cULus Listed outlet boxes

marked “Acceptable for Fan Support of 15.9 kg (35 lbs) or less”.

6.

7.

56”/ 48” Brahm LED | 3

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND

THE BLADE DURING ASSEMBLY OR AFTER INSTALLATION.

DO NOT INSERT OBJECTS IN THE PATH OF THE BLADES.

SAFETY RULES

The fan must be mounted with a minimum of 2.1 m (7 feet)

clearance from the trailing edge of the blades to the floor.

To operate the reverse function on this fan, press the

reverse button while the fan is running.

Avoid placing objects in the path of the blades.

WARNING: make sure the power is disconnected

before cleaning your fan.

To avoid personal injury or damage to the fan and

other items, be cautious when working around or

cleaning the fan.

Do not use water or detergents when cleaning the fan

or fan blades. A dry dust cloth or lightly dampened

cloth will be suitable for most cleaning.

After making electrical connections, spliced

conductors should be turned upward and pushed

carefully up into outlet box. The wires should be spread

apart with the grounded conductor and the

equipment-grounding conductor on one side of the

outlet box and the ungrounded conductor on the other

side of the outlet box.

Electrical diagrams are reference only. Light kits that

are not packed with the fan must be cULus Listed and

marked suitable for use with the model fan you are

installing. Switches must be cULus General Use

Switches. Refer to the Instructions packaged with the

light kits and switches for proper assembly.

All set screws must be checked, and retightened where

necessary, before installation.

The subject fan weight information is as below:

8.

9.

10.

11.

12.

13.

14.

15.

16.

17.

Model

300044

300048

Net Weight

(kgs)

Gross Weight

(kgs)

Net Weight

(lbs)

Gross Weight

(lbs)

9.18 10.22 20.21 22.50

7.58 8.48 16.68 18.66

4 | KICHLER.COM

TOOLS AND MATERIALS REQUIRED

PACKAGE CONTENTS

•Phillips Screwdriver

•Blade Screwdriver

•11 mm Wrench

•Step Ladder

•Wire Cutters

Unpack your fan and check the contents. You should have the following items:

A. Mounting Bracket

B. Ball / Downrod Assembly

C. Canopy

D. Canopy Hole Cover

E. Coupling Cover

F. Motor Body

G. Fan Blade (5)

H. Switch Housing

I. Light Kit

J. Glass

A

B

C

D

E

F

G

I

J

H

L

K. Wall control Kit:

Receiver (1), Control (1), Metal Plate (1),

Wire connector (6), Wood Screw (2),

Battery (2), Long Screw (2),

Short Screw (2), Expansion Anchor (2),

Plastic Nut (2)

K

L. Package Hardware

1) Mounting Hardware:

Wire Connectors (3)

2) Blade Attachment Hardware:

Screws (15), Washers (15)

3) Safety Cable Hardware:

Wood Screw (1)

Spring Washer (1)

Flat Washer (1)

56”/ 48” Brahm LED | 5

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box

and its support must be able to fully support the full weight of

the fan (up to 15.9 kg (35 lbs.)). Do not use plastic outlet boxes.

outlet box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A

minimum clearance of 12" is suggested for optimal operation.

NOTE: Depending on the location you have selected for

installation, you may need to purchase and install a “Joist

Hanger” for the support of the outlet box. Make sure the joist

hanger you purchase has been designed for use with ceiling

fans. (Fig. 4)

Fig. 1

Outlet box

Fig. 2

Fig. 3

Fig. 4

Outlet box

Recessed

outlet box ceiling

mounting

plane

Provide strong

support

ANGLED CEILING

MAXIMUM 20° ANGLE

6 | KICHLER.COM

HANGING THE FAN

To properly install your ceiling fan, follow the steps below.

Step 1. Before attaching fan to outlet box (not included), ensure the outlet box is securely

fastened to at least two points to a structural ceiling member (a loose box will cause the

fan to wobble). Pass the 120 volt supply wires from the ceiling outlet box through the

center of the ceiling mounting bracket. Install mounting bracket to outlet box in ceiling

using the screws and washers included with the outlet box. (Fig. 5)

Step 2. Remove the hairpin and clevis pin from the downrod assembly, retain for later use.

Remove the hanger ball from the downrod assembly by loosening set screw, removing

NOTE: Make sure to keep loosened hardware separate to avoid confusion during

installation.

Step 3. Loosen the two set screws on the motor coupling. (Fig. 7)

Outlet Box

Fig. 5

Fig. 6

Fig. 7

Ceiling Mounting Bracket

Flat Washer

Screw

Hanger Ball

Set Screw

Cross Pin

Hairpin

Clevis Pin

REMEMBER to turn o the power before you begin installation. This is necessary for

your safety and also the proper programming of the control system.

Set Screw

Motor Body

56”/ 48” Brahm LED | 7

HANGING THE FAN (continued)

Step 4. Carefully feed fan wires and safety cable up through the downrod.

Thread the downrod onto the motor coupling until the clevis pin holes are

aligned. Next, replace the clevis pin and hairpin, then tighten both set screws.

(Fig. 8)

Step 5. Slip the coupling cover, canopy hole cover and canopy onto the

downrod. Carefully reinstall the hanger ball onto the downrod. Make sure the

cross pin is in the correct position and the set screw is tight and the wires are

not twisted. (Fig. 9)

Step 6. Now lift the motor body into position and place the hanger ball into

the mounting bracket. Rotate until the “Check Tab” has dropped into the

“Registration Slot” and seats firmly. (Fig. 10) The entire motor body should

not rotate if this is done correctly.

WARNING: Failure to properly seat the “Check Tab” can damage the ceiling

fan during operation.

Fig. 8

Clevis Pin

Clip

Set Screw

Clevis Pin

Motor Body

Clip

Set Screw

Fig. 9

Cross Pin Set Screw

Hanger Ball

Canopy

Canopy Hole Cover

Coupling Cover

Motor Body

Fig. 10

Mounting Bracket Hanger Ball

Registration Slot

Check Tab

8 | KICHLER.COM

Flat Washer

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from faIling, please

install it as follows.

Step 1. Drive a wood screw and washers into the side of the brace that holds the outlet

box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 11)

Step 2. Insert the safety cable through the mounting bracket and one of the holes in

the outlet box into the ceiling. Adjust the length of the safety cable to reach the screw

and washers by pulling the extra cable through the cable clamp until the overall length is

correct, put the end of the cable back through the cable clamp, forming a loop at the end

of the cable. Tighten the cable clamp securely. Now, put the loop in the end of the safety

cable over the wood screw and under the washer. Tighten the wood screw securely.

(Fig. 12)

NOTE: Although the safety support cable is required for Canadian installations only.

It’s a good idea to make the attachment with any installation.

Wood Screw

Spring Washer

Outlet Box

Ceiling

Support Brace

Safety Cable Bolt

Wood Screw

Fig. 12

Fig. 11

56”/ 48” Brahm LED | 9

MAKE THE ELECTRICAL CONNECTIONS

WARNING:

the main circuit panel before wiring.

To avoid possible electrical shock, be sure you have turned o the power at

Follow the steps below to connect the fan to your household wiring. Use the wire

connectors supplied with your fan. Secure the connector with electrical tape. Make sure

there are no loose wire stands or connections.

WARNING:

immediately. A professional electrician is recommended to determine proper wiring.

If your house wires are dierent colors than referenced in this manual, stop

Step 1. Insert the receiver into the mounting bracket, and keep flat in opposition of

ceiling. (Fig. 13)

Step 2. Motor to Receiver Electrical Connections: Connect the BLACK wire from the fan

to BLACK wire marked “TO MOTOR L” from the receiver. Connect the WHITE wire from

the fan to the WHITE wire marked “TO MOTOR N” from the receiver. Connect the BLUE

wire from the fan to the BLUE wire marked “FOR LIGHT “ from the receiver. Secure all

the wire connections with the plastic wire connectors provided. (Fig. 14)

Step 3. Remote Receiver to Outlet Box Electrical Connections: Connect the BLACK (hot)

wire from the ceiling to the BLACK wire marked “AC IN L” from the receiver. Connect

the WHITE (Neutral) wire from the ceiling to the WHITE wire marked “AC IN N” from the

receiver. Secure all the wire connections with the plastic wire connectors provided.

(Fig. 14)

Mounting

Bracket

Fig. 14

Receiver

Fig. 13

Outlet box

Black White

Green or bare

copper (ground)

Black (“AC IN L”)

Receiver

Black (“TO MOTOR L”)

Black (motor)

Blue (FOR LIGHT)

White (“AC IN N”)

White (“TO MOTOR N”)

Ground wire

White (Neutral)

10 | KICHLER.COM

MAKE THE ELECTRICAL CONNECTIONS

Step 4. If your outlet box has a ground wire (green or bare copper) connect it to

the fan ground wires: otherwise connect the fan ground wire to the mounting

bracket. Secure the wire connection with a plastic nut provided. After connecting

the wires, spread them apart so that the green and white wires are on one side of

the outlet box and black and blue wires are on the other side. (Fig. 14)

NOTE: Carefully tuck the wire connections up into the outlet box.

NOTE: Fan must be installed at a maximum distance of 30 feet from the

transmitting unit for proper signal transmission between the transmitting unit

and the fan’s receiving unit.

FINISHING THE MOTOR INSTALLATION

Step 1. Remove one of the two shoulder screws in the mounting bracket. Loosen

the second shoulder screw without fully removing it. (Fig. 15)

Step 2. Assemble canopy by rotating key slot in canopy over shoulder screw in

mounting bracket. Reinstall the shoulder screw that was previously removed,

then retighten two shoulder screws securely. (Fig.16)

Mounting Bracket

Fig. 15

Fig. 16

Shoulder Screw

Canopy

Shoulder Screw

56”/ 48” Brahm LED | 11

FINISHING THE MOTOR INSTALLATION

Step 3. Securely attach and tighten the canopy hole cover over the shoulder

screws in the mounting bracket utilizing the keyslot twist-lock feature. (Fig. 17)

ATTACHING THE FAN BLADES

CAUTION: Before continuing, make sure the power is disconnected by turning o

the circuit breaker or removing the fuse at the circuit box.

Step 1. Carefully slide the blade through the slot as shown. Securely fasten the

five blades with blade screws and flat washers. (Fig. 18)

Fig. 18

Blade

Blade Screw

Flat Washer

Shoulder Screw

Canopy Hole Cover

Fig. 17

12 | KICHLER.COM

INSTALLING THE SWITCH HOUSING

Step 1.

CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The Electrical

Supply Circuit To The Fan Before Installing Switch Housing.

Remove the screw marked with a dot label which is preinstalled on

mounting plate and keep for later use. Loosen the other two (do not remove).

Place the two slot holes on the switch housing over the 2 screws previously

loosened from the mounting plate. Rotate the switch housing until it locks in

place at the narrow end of the key holes. Secure by tightening the 2 screws

previously loosened and the one previously removed. (Fig. 19)

Screw

Fig. 19

Switch Housing

Mounting Plate

56”/ 48” Brahm LED | 13

INSTALLING THE LIGHT KIT AND GLASS

CAUTION:

o at the main circuit breaker or by removing the circuit fuse. Turning the power

Before continuing installation, confirm that the power is still turned

o using a wall switch is not sucient to prevent electrical shock.

Step 1. Hold the light kit close to the switch housing and connect the WHITE

wires from the light kit and fan by pushing the connectors together. Follow the

same procedure with the BLACK wires. (Fig. 20)

Step 2. Tuck the connections neatly into the light kit. Remove one of three

screws pre-installed on the switch housing and keep for later use. Loosen the

other 2 screws (do not remove). Place the two slot holes on the light kit over

the 2 screws previously loosened from the switch housing. Rotate the light kit

until it locks in place at the narrow end of the key holes. Secure by tightening

the 2 screws previously loosened and the one previously removed. (Fig. 20)

Step 3. Secure the glass to switch housing by twisting in a clockwise direction,

twist the glass gradually until it snaps on to the switch housing. Do not over -

tighten. (Fig. 21)

Glass

Fig. 20

Fig. 21

Light Kit

14 | KICHLER.COM

CAUTION: MAKE SURE THE ELECTRICITY IS TURNED OFF AT THE MAIN JUNCTION

BOX OR THE CORRECT FUSE HAS BEEN PULLED OFF AT THE MAIN JUNCTION BOX

BEFORE CONTINUING.

WARNING: All wiring must be in accordance with the National Electrical Code local

electrical codes. Electrical installation should be performed by a qualified licensed

electrician.

Select a location to install your “CoolTouch” Control System Transmitter. You can replace

an existing wall switch, or install the transmitter on ANY flat surface.

WARNING: SWITCH INSTALLATION MUST COMPLY WITH ALL LOCAL AND

NATIONAL ELECTRIC CODES.

Option 1. Install the control system using an existing wall switch outlet box.

Make sure the electrical power is TURNED OFF at the main panel before wiring.

Step 1. Remove the existing wall plate and the old switch from the wall outlet box. Wire the

BLACK leads (hot) together with connector and push back inside the outlet box. (Fig. 22)

Step 2. Install the metal plate and “CoolTouch” wall plate to the existing wall outlet box

with 4 screws provided. Then place the two plastic plugs into the wall plate. (Fig. 23)

Option 2: Install the control system on ANY flat surface:

Select the desired location and use the “CoolTouch” wall plate to make the location for the

mounting holes. Plastic wall anchors and screws are provided for this type of installation.

After installing the wall anchors, attach the “CoolTouch” wall plate with the mounting

screws and then insert the plastic plugs to finish installation.

INSTALLING THE COOLTOUCH™ CONTROL SYSTEM WALL PLATE

Fig. 22

Fig. 23

Outlet Box

Switch

Wall Plate

Outlet Box

Metal Plate

Screw

“CoolTouch” Wall Plate

Screw

Plastic Plug

56”/ 48” Brahm LED | 15

INSTALLING AND REMOVING THE HANDHELD TRANSMITTER

Step 1. To place the transmitter in the wall plate, put the bottom end in first and

then press the top into the wall plate. The transmitter is now held in the wall plate

and will function from here. (Fig.24)

Step 2. To remove the transmitter from the wall plate, push the release button

and the transmitter will fall into your hand.

Fig. 24

OPERATING INSTRUCTIONS

WARNING: Chemical Burn Hazard. Keep batteries away from children.

Step 1. Using a screwdriver, remove the battery cover from the handset and save

the screw for later use. (Fig. 25)

Step 2. To make fan operational, install two 3V CR2032 batteries (included). The

batteries should be installed with the positive (+) side up. Replace with CR2032

batteries when necessary. (Fig. 26)

NOTE: If not used for long periods of time, remove batteries to prevent damage

to the handset control. Store the control away from excessive heat or humidity.

Fig. 25

Fig. 26

Batteries

16 | KICHLER.COM

OPERATING INSTRUCTIONS

NOTE: Each handset control carries a unique ID code to facilitate communication between paired

devices. The ID code is set by factory and is not user changeable. However, you will be required to

perform an ID code learning process manually under these circumstances:

• If you have multiple fans installed within a close proximity and want to control all fans using a

same handset control.

NOTE: Each fan requires its own receiver.

• When your remote control is not responding (make sure battery is not dead).

• After you have replaced a faulty transmitter or receiver with a new one.

Otherwise the remote control will not work. To perform this process manually, follow steps below:

After installing and wiring the unit, restore power to your fan, press and hold the “LEARN” key

for 1-3 seconds, and the fan will turn on at medium speed and light (if installed) will turn on. This

confirms that the learning process has been completed. This operation must be completed within

30 seconds after restoring power to the fan. (Fig. 27)

NOTE: Ensure slide switch in battery compartment marked “D O” is set to “D” position. (Fig. 27)

Step 4. Replace the battery cover and tighten with screwdriver. (Fig. 27)

Step 5. The buttons control the fan speed and light as follows: (Fig. 28)

Fig. 30

Fig. 29

Battery Cover

Screw

Fig. 27

Fig. 28

Battery Cover

Screw

Low speed

Medium speed

High speed

Fan OFF

Airflow (Forward or Reverse)

No function (Do not use this button)

a.) Light ON/OFF.

b.) Press and hold to dim or brighten light to desired level.

56”/ 48” Brahm LED | 17

Fig. 29 Fig. 30

REVERSE FUNCTION

To operate the reverse function on this fan, press the “Reverse”

button while fan is running. Speed setting for warm or cool weather

depends on factors such as the room size, ceiling height, number of

fans and so on.

Warm Weather Operation: Forward (counter clockwise).A downward

comfort.

Cool Weather Operation: Reverse (clockwise). An upward airflow

moves warm air o of the ceiling (Fig. 30). This allows you to set

comfort.

FCC Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.)This device may not cause harmful interference, and

2.)This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician or help.

(Fig. 29).

18 | KICHLER.COM

TROUBLESHOOTING

Problem

Fan will not start.

Fan sounds noisy.

Fan wobble.

Remote control

malfunction.

Solution

1. Check circuit fuses or breakers.

2. Check all electrical connections to ensure proper contact. CAUTION: Make sure the main power is OFF when checking

any electrical connection.

3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out.

4. Ensure the batteries have a good charge.

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade brackets to the motor are tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappears during this time.

5. If using an optional light kit, make sure the screws securing the glassware are tight. Make sure the light bulbs are not

touching any other component.

6. Do not connect this fan to a wall mounted variable speed control(s). They are not compatible with ceiling fan motors or

remote controls.

7. Make sure the upper canopy has a short distance from the ceiling. It should not touch the ceiling.

1. Check that all blade and blade arm screws are secure.

2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling

above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is positioned for measurement.

Repeat for each blade. The distance deviation should be equal within 1/8".

3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and

possibly result in smoother operation.

CAN NOT EXCEPT1.Ceiling Fans with remote control systems CAN NOT be operated in conjunction with any other control system EXCEPT a

56”/ 48” Brahm LED | 19

REV. 2022/8/5

www.kichler.com

KICHLER LIGHTING LLC

30455 Solon Rd.

Solon, OH 44139 USA

CUSTOMER SERVICE 866.558.5706

8:00 AM TO 5:00 PM EST, MONDAY - FRIDAY

La page charge ...

Kichler 300044 Manuel utilisateur

Kichler 300044 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents