Hitachi WR 12DH Instruction Manual And Safety Instructions

MODEL Variable speed CORDLESS IMPACT WRENCH

MODÈLE CLÉ À CHOC À BATTERIE

MODELO LLAVE DE IMPACTO A BATERÍA

WR 12DH

MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE

AVERTISSEMENT

Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi avant d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs avant

qu’ils utilisent l’outil motorisé.

INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS

WARNING

Improper and unsafe use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual before operating the power tool. Please keep this

manual available for others before they use the power tool.

MANUAL DE INSTRUCCIONES E INSTRUCCIONES DE SEGURIDAD

ADVERTENCIA

¡La utilización inapropiada e insegura de esta herramienta eléctrica puede resultar

en lesiones serias o en la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual antes de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de que utilicen la

herramienta eléctrica.

CONTENTS

English

Page

IMPORTANT INFORMATION ............................. 3

MEANINGS OF SIGNAL WORDS ....................... 3

SAFETY .................................................................... 4

GENERAL SAFETY RULES – FOR ALL

BATTERY OPERATED TOOLS ..................... 4

SPECIFIC SAFETY RULES ................................... 6

IMPORTANT SAFETY INSTRUCTIONS FOR

USE OF THE CORDLESS IMPACT WRENCH ....

7

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER ............................ 7

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER .................................... 9

FUNCTIONAL DESCRIPTION ................................ 10

MODEL ............................................................... 10

NAME OF PARTS .............................................. 10

TABLE DES MATIERES

ÍNDICE

Página

ESPECIFICACIONES ............................................ 58

MONTAJE Y OPERACIÓN ....................................... 59

APLICACIONES ................................................... 59

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA ............................................ 59

MÉTODO DE CARGA .......................................... 59

ANTES DE LA UTILIZACIÓN .............................. 62

OPERACIÓN ......................................................... 62

PRECAUCIONES OPERACIONALES .................. 64

MANTENIMIENTO E INSPECCIÓN ........................ 67

ACCESORIOS ........................................................... 69

ACCESORIOS ESTÁNDAR .................................. 69

ACCESORIOS OPCIONALES .............................. 69

LISTA DE PIEZAS .................................................... 74

Page

SPECIFICATIONS .............................................. 11

ASSEMBLY AND OPERATION ............................. 12

APPLICATIONS .................................................. 12

REMOVAL AND INSTALLATION METHOD

OF BATTERY .................................................. 12

CHARGING METHOD ........................................ 12

BEFORE USE ..................................................... 15

OPERATION ....................................................... 15

OPERATIONAL CAUTIONS .............................. 16

MAINTENANCE AND INSPECTION ..................... 19

ACCESSORIES ....................................................... 21

STANDARD ACCESSORIES ............................. 21

OPTIONAL ACCESSORIES ............................... 21

PARTS LIST ............................................................ 74

Page

INFORMATIONS IMPORTANTES ...................... 25

SIGNIFICATION DES MOTS D’AVERTISSEMEN

T .... 25

SECURITE ................................................................ 26

REGLES GENERALE DE SECURITE – POUR TOUS

LES OUTILS FONCTIONNANT SUR BATTERIE ...

26

REGLES DE SECURITE SPECIFIQUES ............... 28

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR

L'UTILISATION DU CLÉ À CHOC À BATTERIE

.....

29

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR L’UTILISATION DU CHARGEUR DE BATTERIE ...

30

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR L’UTILISATION

DE LA BATTERIE ET DU CHARGEUR DE BATTERIE ...............

31

DESCRIPTION FONCTIONNELLE ........................... 33

MODELE ............................................................... 33

NOM DES PARTIES ............................................. 33

Page

SPECIFICATIONS ................................................ 34

ASSEMBLAGE ET FONCTIONNEMENT ..........................

35

UTILISATIONS ..................................................... 35

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 35

MÉTHODE DE RECHARGE ................................. 35

AVANT L’UTILISATION ...................................... 38

UTILISATION ....................................................... 38

PRÉCAUTIONS D'UTILISATION ......................... 40

ENTRETIEN ET INSPECTION .................................. 43

ACCESOIRES ........................................................... 45

ACCESSOIRES STANDARD ............................... 45

ACCESSOIRES EN OPTION ................................ 45

LISTE DES PIÉCES ................................................... 74

Français

Español

Página

INFORMACIÓN IMPORTANTE ........................... 49

SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN

.. 49

SEGURIDAD ............................................................. 50

NORMAS GENERALES DE SEGURIDAD – PARA TODAS

LAS HERRAMIENTAS ALIMENTADAS CON BATERÍA

.. 50

NORMAS ESPECÍFICOS DE SEGURIDAD ......... 52

INSTRUCCIONES IMPORTANTES PARA LA UTILIZACIÓN

DEL LLAVE DE IMPACTO A BATERÍA ..........................

53

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA EL CARGADOR DE BATERÍAS

................. 54

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA LA BATERÍA Y EL CARGADOR DE BATERÍAS

... 55

DESCRIPCIÓN FUNCIONAL .................................... 57

MODELO .............................................................. 57

NOMENCLATURA ............................................... 57

English

3

IMPORTANT INFORMATION

Read and understand all of the operating instructions, safety precautions and warnings in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and

in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

Never use this power tool in a manner that has not been specifically recommended by

HITACHI, unless you first confirm that the planned use will be safe for you and others.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

serious personal injury.

CAUTION indicates a hazardous situations which, if ignored, could result in moderate

personal injury, or could cause machine damage.

NOTE emphasizes essential information.

English

4

SAFETY

GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric

shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery.

A charger that may be suitable for one type of battery may create a risk of fire when

used with another battery.

(2) Use battery operated tool only with specifically designed battery pack.

Use of any other batteries may create a risk of fire.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your

hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or long hair

can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with

your finger on the switch or plugging in tools that have the switch on invites accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that

is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear protective grasses. Dust mask, non-skid safety

shoes, hard hat, or ear plugs must be used for appropriate conditions.

English

5

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to

lose of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tools. Such

preventive safety measures reduce the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hand of untrained users.

(6) When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may cause sparks, burns, or a fire.

(7) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(8) Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect the tools operation. If damaged, have the tool serviced

before using. Many accidents are caused by poorly maintained tools.

(9) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used on

another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts of failure to follow

Maintenance Instruction may create a risk of electric shock or injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter

out microscopic particles.

English

6

SPECIFIC SAFETY RULES

1. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

2. Never touch moving parts.

Never place your hands, fingers or other body parts near the tool’s moving parts.

3. Never operate without all guards in place.

Never operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

4. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for cutting

tree limbs or logs.

5. Never use a power tool for applications other than those specified.

Never use a power tool for applications other than those specified in the Instruction

Manual.

6. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw the

tool. Never allow the tool to be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

7. Definitions for symbols

V .... volts

---

............. direct current

n

o

............ no load speed

---/min ..... revolutions or reciprocation per minute

8. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

9. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

10. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to youself or others. Blades, cutting implements and accesso-

ries which have been mounted to the tool should be secure and tight.

11. Never use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

12. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may be

deformed, cracked, or damaged.

13. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

English

7

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE

CORDLESS IMPACT WRENCH

WARNING: Death or serious bodily injury could result from improper or unsafe use

of the cordless impact wrench. To avoid these risks, follow these basic

safety instructions:

1. Never use this wrench handle for any application other than those in this manual.

2. When working in high places, always make sure that there is no one below before starting

to work.

3. Always wear eye and ear protection when you work.

4. Confirm whether the socket has any crack in it.

5. Attach the hex. socket securely onto the anvil. If the hex. socket is insufficiently secured,

it may drop out and cause an accident. For hex. socket attachment refer to “OPERATION”

on page 15.

6. Confirm the tightening torque by a torque wrenck before use in order to ascertain the

correct tightening torque to be used.

7. If a universal joint is used, be sure not to operate the unit in a no-load condition. Operatig

in this condition is dangerous. When the socket section spins around it may cause injury

to hands or bodies, or the resuluting intense vibration may cause the user to drop the tool.

8. Be careful that foreign matters do not block the holes located on both sides of the handle.

Also do not close the holes with a tape. The holes act an important role.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

1. This manual contains important safety and operating instructions for battery charger

Model UC 14YF/UC14YF2.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI rechargeable battery type EB7, EB9, EB12, EB14

series. Other type of batteries may burst causing personal injury and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold by the battery charger manufacturer may

result in a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug when disconnecting

battery charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

English

8

a. That blades of extension cord are the same number, size, and shape as those of plug

on battery charger:

b. That extension cord is properly wired and in good electrical condition; and

c. That wire size is large enough for AC ampere rating of battery charger as specified

in Table 1.

* If the input rating of a battery charger is given in watts rather than in amperes, the

corresponding ampere rating is to be determined by dividing the wattage rating by the

voltage rating–for example:

9. Do not operate battery charger with damaged cord or plug-replace them immediately.

10. Do not operate battery charger if it has received a sharp blow, been dropped, or

otherwise damaged in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a qualified serviceman when service or

repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

12. To reduce risk of electric shock, unplug charger from receptacle before attempting any

maintenance or cleaning. Removing the battery will not reduce this risk.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

1250watts

125 volts

= 10 amperes

English

9

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE

BATTERY AND BATTERY CHARGER

You must charge the battery before you can use the cordless impact wrench. Before using

the model UC 14YF/UC14YF2 battery charger, be sure to read all instructions and cautionary

statements on it, the battery and in this manual.

REMEMBER: USE ONLY HITACHI BATTERY TYPES EB7 SERIES, EB9 SERIES, EB12 SERIES,

EB14 SERIES. OTHER TYPES OF BATTERIES MAY BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING: Improper use of the battery or battery charger can lead to serious injury.

To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or is completely worn out. The

battery can explode in a fire.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s air vents. Electric shock or

damage to the battery charger may result.

5. NEVER charge outdoors. Keep the battery away from direct sunlight and use only

where there is low humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F (0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to charge.

11. NEVER store the battery or battery charger in places where the temperature may

reach or exceed 104°F (40°C).

12. ALWAYS operate charger on standard household electrical power (120 volts). Using

the charger on any other voltage may overheat and damage the charger.

13. ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.

14. ALWAYS disconnect the power cord from its receptacle when the charger is not in use.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS OF THIS TOOL!

English

10

MODEL

WR 12DH: with charger (UC 14YF or UC 14YF2) and case

NAME OF PARTS

1. Cordless Impact Wrench (WR 12DH)

䡬 Battery (EB12B)

FUNCTIONAL DESCRIPTION

NOTE: The information contained in this Instruction Manual is designed to assist you in the

safe operation and maintenance of the power tool.

Some illustrations in this Instruction Manual may show details or attachments that

differ from those on your own power tool.

Fig. 1

Nameplate

Latch

Terminal Hole

Nameplate

Switch Trigger

Handle

Battery (EB12B)

Push Button

Housing

Air Vents

English

11

2. Battery Charger (UC 14YF/ UC 14YF2)

Pilot Lamp

Cord

Battery Installation Hole

Caution Plate

Body

Fig. 2

Nameplate

SPECIFICATIONS

1. Cordless Impact Wrench (WR 12DH)

Motor DC motor

No-load speed

0–2200/min

Capacity 1/4″ – 9/16″ (M6 – M14) (Ordinary bolt)

1/4″ – 3/8″ (M6 – M10) (High tension bolt)

Tightening torque Maximum 87 ft-lbs (1200 kg-cm)

Tightening is 9/16″ (M14) high tension bolt, when fully

charged in 68° F (20°C) temp.

Tighttening time: 3 sec.

Battery (EB12B) Nickel cadmium battery

Voltage .......................................................... DC12V

Charging & discharging frequency ............. about 1000

Weight 3.7 lbs (1.7 kg)

Input power source Single phase: AC120V 60Hz

Charging time Approx. 60min. (At a temperature of 68°F (20°C))

Charger

Charging voltage .......................... DC 7.2–14.4V

Charging current........................... DC 1.9A

Weight 2.9 lbs (1.3kg)

2. Battery Charger (UC 14YF/UC 14YF2)

English

12

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Tightening and loosening of all types of bolts and nuts, used for securing structural

items.

REMOVAL AND INSTALLATION METHOD OF BATTERY

䡬 How to install the battery.

Align the battery with the groove in tool

handle and slip it into place.

Always insert it all the way until it locks in

place with a little click, If not, it may acciden-

tally fall out of the tool, causing injury to

you or someone around you. (Fig. 3)

䡬 How to remove the battery.

Withdraw battery from the tool handle while

pressing the latch on the side of the battery.

(Fig. 3)

CHARGING METHOD

NOTE: Before plugging into the receptacle, make sure the following points.

䡬 The power source voltage is stated on the nameplate.

䡬 The cord is not damaged.

WARNING: Do not charge at voltage higher than indicated on the nameplate.

If charged at voltage higher than indicated on the nameplate, the

charger will burn up.

1. Insert the plug of battery charger into

the receptacle.

When the plug of battery charger has been

inserted into the receptacle, pilot lamp will

blink in red. (At 1-second intervals)

WARNING: Do not use the electrical

cord if damaged. Have it

repaired immediately.

Fig. 4

d

Rechargeable

battery

Insert

Pilot lamp

Hole for connect-

ing the recharge-

able battery

Handle

Rechargeable

battery

Latch

Insert

Pull out

Fig. 3

English

13

Table 2

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Charging

impossible

Malfunction in the battery or the

charger

The battery temperature is high,

making recharging impossible.

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flikers

(RED)

Lights

(GREEN)

Table 3 Recharging of batteries that have become hot

Temperatures at which the battery can be recharged

23°F—140°F

(–5°C—60°C)

Rechargeable batteries

EB 12B

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in Fig. 4. Make sure it contacts the

bottom of the battery charger.

CAUTION:

● If the batteries are inserted in the reverse direction, not only recharging will become

impossible, but it may also cause problems in the charger such as a deformed recharging

terminal.

3. Charging

When the battery is connected to the battery charger, charging will commence and the

pilot lamp will light in red. (See Table 2)

NOTE: If the pilot lamp flikers in red, pull out the plug from the receptacle and check if

the battery is properly mounted.

When the battery is fully charged, the pilot lamp will blink in red slowly. (At 1-second

intervals) (See Table 2)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in Table 2, according to the condition

of the charger or the rechargeable battery.

(2) Regarding the temperature of the rechargeable battery.

The temperatures for rechargeable batteries are as shown in the table below, and

batteries that have become hot should be cooled for a while before being recharged.

English

14

(3) Regarding recharging time (At 68°F (20°C))

In approx. 60 minutes.

NOTE: The charging time may vary according to temperature and power source voltage.

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

CAUTION:

● When the battery charger has been continuosly used, the battery charger will heated,

thus constituting the cause of the failures. Once the charging has been completed, give

15 minutes rest until the next charging.

● If the battery is rechraged when it is warm due to battery use or exposure to sunlight,

the pilot lamp may light in green.

The battery will not be recharged. In such a case, let the battery cool before charging.

● When the pilot lamp flikers rapidly in red (at 0.2–second intervals), check for and take

out any foreign objects in the charger’s battery installation hole. If there are no foreign

objects, it is probable that the battery or charger is malfunctioning. Take it to your

authorized Service Center.

● Since the built-in micro computer takes about 3 seconds to confirm that the battery

being charged with UC 14YF/UC 14YF2 is taken out, wait for a minimum of 3 seconds

before reinserting it to continue charging. If the battery is reinserted within 3 seconds,

the battery may not be properly charged.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been

used for an extended period is not activated, the electric discharge might be low when

using them the first and second time. This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and

recharge its battery. If you continue to use the tool and exhaust the electric current, the

battery may be damaged and its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged

immediately after use, its internal chemical substance will deteriorate, and the battery

life will be shortened. Leave the battery and recharge it after it has cooled for a while.

English

15

BEFORE USE

Check the work area to make sure that it is clear of debris and clutter.

Clear the area of unnecessary personnel. Ensure that lighting and ventilation is adequate.

OPERATION

1. Selecting the socket matched to the bolt

Be sure to use a socket which is matched to the bolt

to be tightened. Using an improper socket will not

only result in insufficient tightening but also in

damage to the socket or nut.

A worn or deformed hex or square-holed socket

will not give an adequate tightness for fitting to the

nut or anvil, consequently resulting in loss of tight-

ening torque.

Pay attention to wear of socket hole, and replace

before further wear has developed.

Matching socket and bolt sizes are shown Tables 4

and 5. The numerical value of a socket designation

denotes the side-to-side distance (H) of its hex.

hole.

2. Installing a socket (Fig. 5, 6)

Align the plunger located in the square part of the

anvil with the hole in the hex. socket. Then push the

plunger, and mount the hex. socket on the anvil.

Check that the plunger is fully engaged in the hole.

When removing the socket, reverse the sequence.

3. Removing the socket

Please do the opposite point on the method of

installing socket.

4. Confirm that the battery is mounted correctly.

5. Check the rotational direction

The bit rotates clockwise (viewed from the rear

side) by pushing the R-side of the push button.

The L-side of the push button is pushed to turn the

bit counterclockwise. (See Fig. 7). (The

L

and

R

marks are engraved on the body.)

CAUTION

The push button can not be switched while the impact driver is turning. To switch the

push button, stop the impact driver, then set the push button.

6. Switch operation

䡬 When the trigger switch is depressed, the tool rotates. When the trigger is released, the

tool stops.

Plunger

Anvil

Hole

Fig. 6

Hexagonal

socket

Fig. 7

R L

Push

button

Fig. 5

Groove

Hexagonal

socket

Anvil

English

16

䡬 The rotational speed can be controlled by varying the amount that the trigger switch is

pulled. Speed is low when the trigger switch is pulled slightly and increases as the trigger

switch is pulled more.

NOTE

A buzzing noise is produced when the motor is about to rotate; this is only a noise, not

a machine failure.

7. Tightening and loosening bolts

A hex socket matching the bolt or nut must first be selected. Then mount the socket on

the anvil, and grip the nut to be tightened with the hex socket. Holding the wrench in line

with the bolt, press the power switch to impact the nut for several seconds.

If the nut is only loosely fitted to the bolt, the bolt may turn wit the nut, therefore mistaking

proper tightening. In this case, stop impact on the nut and hold the bolt head with a

wrench before restarting impact, or manually tighten the bolt and nut to prevent them

slipping.

8. Number of bolt tightened possible (with one charge (EB12B))

Please refer to the table below for the number of bolt tightened possible with one charge.

These values may vary slightly, according to surrounding temperature and battery

characteristics.

OPERATIONAL CAUTIONS

1. Cautions on use of the speed control switch

This switch has a built-in, electronic circuit which steplessly varies the rotation speed.

Consequently, when the switch trigger is pulled only slightly (low speed rotation) and the

motor is stopped while continuously driving in screws, the components of the electronic

circuit parts may overheat and be damaged.

2. Tightening torque

Refer to Fig. 8, 9 and 10 for the tightening torque of bolts (according to size), under the

conditions shown in Fig. 11. Please use this example as a general reference, as tightening

torque will vary according to tightening conditions.

Tightening torque varies, depending on the battery’s charge level. Fig. 12 shows an

example of the relationship between tightening torque and the number of tightenings,

for a 9/16″ × 2″ (M14 × 50) high tension bolt. As shown, tightening torque gradually

weakens with the increase in the number of tightenings. In particular, as the torque

decreases very close to the complete discharge (“a” margin in graph), the unit’s impact

weakens, the number of time impacts declines and tightening torque drops off abruptly.

If this occurs, check torque level, then recharge the battery if necessary.

NOTE

䡬 If a long striking time is used, screws will be strongly tightened. This may cause the screw

to break, or may damage the end of the bit.

䡬 If the unit is held at an angle to the screw being tightened, the head of the screw may be

damaged, or the specified torque may not be transmitted to the screw. Always keep the

unit and the screw being tightened in a straight line.

Bolt used No. of tightenings

High tension bolt 15/32″ × 1–3/4″ (M12 × 45) Approx. 130

English

17

0123

0

200

(14)

400

(29)

600

(43)

800

(58)

1000

(72)

1200

(86)

kg–cm

(ft–lb)

15/32″ × 1–3/4″

(M12 × 45)

0

0123

200

(14)

400

(29)

600

(43)

800

(58)

1000

(72)

kg–cm

(ft–lb)

5/16″ × 1–3/6″

(M8 × 30)

0123

0

200

(14)

400

(29)

600

(43)

800

(58)

1000

(72)

kg–cm

(ft–lb)

3/8″ × 1–3/6″

(M10 × 30)

Tightening time: sec

(Steel plate thickness

t = 3/8″ (10 mm))

Fig. 8

Tightening time: sec

(Steel plate thickness

t = 3/8″ (10 mm))

Fig. 9

Tightening time: sec

(Steel plate thickness

t = 1″ (25 mm))

Fig. 10

Tightening torque

High tension bolt

Ordinary bolt

High tension bolt

Ordinary bolt

High tension bolt

Ordinary bolt

Fig. 11

Bolt

Nut

Steel plate

thickness t

Explanation of strength grade:

4 — Yield point of bolt: 45,500 psi (32 kgf/mm

2

)

8 — Pulling strength of bolt: 56,900 psi (40 kgf/mm

2

)

*The following bolt is used.

Ordinary bolt: Strength grade 4.8

High tensile bolt: Hardness division 12.9

(

)

Number of tightenings (PCS)/charging

Fig. 12

M14 × 50 High tensile bolt (tightening time 3 sec)

Tightening torque

a

When full recharged

When completely discharged

0 20 40 60 80 100 120

0

400

(29)

800

(58)

1200

(87)

kg–cm

(ft–lb)

English

18

3. Use a tightening time suitable for the screw

The appropriate torque for a screw differs according to the material and size of the screw,

and the material being screwed etc., so please use a tightening time suitable for the

screw. In particular, if a long tightening time is used in the case of screws smaller than

5/16” (8 mm), there is a danger of the screw breaking, so please confirm the tightening

time and the tightening torque beforehand.

4. Work at a tightening torque suitable for the bolt under impact

The optimum tightening torque for nuts or bolts differs with material and size of the nuts

or bolts. An excessively large tightening torque for a small bolt may stretch or break the

bolt. The tightening torque increases in proportionate to the operaton time. Use the

correct operating time for the bolt.

5. Holding the tool

Hold the impact wrench firmly with both hands. In this case hold the wrench in line with

the bolt.

It is not necessary to push the wrench very hard. Hold the wrench with a force just

sufficient to counteract the impact force.

6. Confirm the tightening torque

The following factors contribute to a reduction of the tightening torque. So confirm the

actual tightening torque needed by screwing up some bolts before the job with a hand

torque wrench. Factors affecting the tightening torque are as follows.

(1) Voltage

When the discharge margin is reached, voltage decreases and tightening torque is

lowered.

(2) Operating time

The tightening torque increases when the operating time increases. But the tightening

torque does not increase above a certain value even if the tool is driven for a long time.

(See Fig. 8, 9 and 10)

(3) Diameter of bolt

The tightening torque differs with the diameter of the bolt as shown in Fig. 8, 9 and 10.

Generally a larger diameter bolt requires larger tightening torque.

(4) Tightening conditions

The tightening torque differs according to the torque ratio; class, and length of bolts even

when bolts with the same size threads are used. The tightening torque also differs

according to the condition of the surface of workpiece through which the bolts are to be

tightened. When the bolt and nut turn together, torque is greatly reduced.

(5) Using optional parts

The tightening torque is reduced a little when an extension bar, universal joint or a long

socketis used.

(6) Clearance of the socket

A worn or deformed hex or a square-holed socket will not give an adequate tightness to

the fitting between the nut or anvil, consequently resulting in loss of tightening torque.

Using an improper socket which does not match to the bolt will result in an insufficient

tightening torque. Matching socket and bolt sizes are shown in Table 4 and 5.

English

19

MAINTENANCE AND INSPECTION

CAUTION: Pull out battery before doing any inspection or maintenance.

1. Checking the condition of the socket.

A worn or deformed hex or a square-holed socket will not give an adequate tihgtness to

the fitting between the nut or anvil, consequently resulting in loss of tihgtening torque.

Pay attention to wear of a socket holes periodically, and replace with a new one if needed.

2. Check the Mounting Screws

Loose mounting screws are dangerous. Regularly inspect them and make sure they are

tight.

CAUTION: Using this power tool with loosen, screws is extremely dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 13)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn

carbon brush can result in motor trouble, replace

the carbon brush with new ones when it becomes

worn to or near the “wear limit”. In addition,

always keep carbon brushes clean and ensure that

they slide freely within the brush holders.

NOTE:

When replacing the carbon brush with a new one,

be sure to use the Hitachi Carbon Brush Code No.

999054.

5. Replacing carbon brushes

Take out the carbon brush by first removing the

brush cap and then hooking the protrusion of the

carbon brush with a flat head screw driver, etc., as

shown in Fig. 15.

When installing the carbon brush, choose the di-

rection so that the nail of the carbon brush agrees

with the contact portion outside the brush tube.

Then push it in with a finger as illustrated in Fig. 16.

Lastly, install the brush cap.

Fig. 14

Fig. 13

Fig. 15

Wear limit

Nail of carbon brush

Protrusion

of carbon

brush

0.12″ (3mm)

0.45″

(11.5mm)

English

20

CAUTION:

Be absolutely sure to insert the nail of the carbon

brush into the contact portion outside the brush

tube. (You can insert whichever one of the two

nails provided.)

Caution must be exercised since any error in this

operation can result in the deformed nail of the

carbon brush and may cause motor trouble at an

early stage.

6. Check for Dust

Dust may be removed with a soft cloth or a cloth dampened with soapy water.

Do not use bleach, chlorine, gasoline or thinner, for they may damage the plastics.

7. Disposal of the exhausted battery

WARNING: Do not dispose of the exhausted battery. The battery must explode if it

is incinerated. The product that you have purchased contains a re-

chargeable battery. The battery is recyclable. At the end of it’s useful

life, under various state and local laws, it may be illegal to dispose of this

battery into the municipal waste stream. Check with your local solid

waste officials for details in your area for recycling options or proper

disposal.

8. Storage

Storing in a place below 104°F (40°C) and out of the reach of children.

9. Service and repairs

All quality power tools will eventually require servicing or replacement of parts because

of wear from normal use. To assure that only authorized replacement parts will be used,

all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE CENTER,

ONLY.

Fig. 16

Contact portion

outside brush tube

La page charge ...

Hitachi WR 12DH Instruction Manual And Safety Instructions

Ce manuel convient également à

Hitachi WR 12DH Instruction Manual And Safety Instructions

dans d''autres langues

Documents connexes

Autres documents