QUICK START GUIDE
Support
randmcnally.com/support
877-446-4863
OVERDRYVEPRO_II_QSG_080620_v001
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC SAR exposure limits set forth for an uncontrolled environment.
SAR compliance for using the equipment in close proximity to the human body has been
evaluated at 0mm.
This equipment must not be co-located or operating in conjunction with any other antenna
or transmitter.
End-users and installers must be provide with antenna installation instructions and consider
removing the no-collocation statement.
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
This equipment should be installed and operated with a minimum distance of 0mm between
the radiator and your body.
Cet équipement devrait être installé et actionné avec une distance minimum de 0mm entre
le radiateur et votre corps.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre
antenne ou émetteur.
LE-LAN devices are restricted to indoor operation only in the band 5150-5250 MHz.
However, original equipment manufacturer (OEM) devices, which are installed in vehicles by
vehicles manufacturers, are permitted.
Les périphériques LE-LAN sont limités au fonctionnement en intérieur uniquement dans
la bande 5150-5250 MHz. Cependant, les dispositifs du fabricant d'équipement d'origine
(OEM), qui sont installés dans les véhicules par les fabricants de véhicules, sont autorisés.
This radio transmitter (IC: 10199A-1000DA) has been approved by Industry Canada
to operate with the antenna types listed below with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
Function Frequency Model Number Type Connector Gain(dBi)
FM Tx 98MHz SZ20051WB52 Dipole SMA -3db
Bluetooth 2.45GHz SZ20051IA93 PIFA IPEX -1.3db
WiFi 2.4 2.45GHz SZ20051IA93 PIFA IPEX -1.2db
GPS 1.575GHz SZ20051IA93 Patch IPEX -2db
XM Radio 2.332GHz R16-A361 Patch SMB -1.0db
Antenna Information
OverDryve
™
Pro II Quick Start Guide
2 3
OverDryve
™
Pro II Quick Start GuideOverDryve
™
Pro II Quick Start Guide
Your OverDryve
™
Pro II Unit
Caution: Important Safety Information
Navigation
• Use this device at your own risk.
• Attend to this device only when it is safe to do so.
• Traffic laws and regulations always have priority over any
instructions from the navigation system.
NOTE: If you do not understand the spoken instructions or are unsure
of what to do, refer to the navigation map on your device.
Installation
• Make sure that the mount is securely mounted and properly
adjusted before each trip.
• Make sure that the mount does not impair the driver’s visibility.
• Do not attach the mount within the airbag deployment zone.
• Install the mount in a manner that minimizes risk in the event of
an accident.
• After installation, check all safety-related equipment to ensure that
it operates without interference from the device, its cables, or any
other accessories.
• Connect the wall charger to a 120-volt or 240-volt outlet only.
• Connect the vehicle charger to a 12-volt outlet only.
Device
• Do not use sharp-edged objects on the device touch screen.
• The device is not waterproof and is not protected against
water damage.
• Protect the device from extreme temperatures. Operating
temperature for the device is between 32 degrees F and
120 degrees F.
• Do not open the device casing.
• Do not attempt to replace the battery. Contact Rand McNally
Customer Support with questions about the battery.
• Always follow local regulations when disposing of this device.
NOTE: Make sure that there are no kinks in the cable and that it will
not be damaged by any sharp objects.
NOTE: Use only a moist cloth to clean the device.
NOTE: Do not pull the cable to unplug the unit.
Your OverDryve
™
Pro II
Box Contents
• OverDryve
™
Pro II Unit
• Smart mount with SiriusXM
®
• Bracket with suction cup
• Truck charger
• USB cable and wall charger
• Dash mount disc
• FM transmitter antenna
• AUX cable
• Anti-glare screen protector
• SiriusXM
®
magnetic mount antenna
• Alcohol prep pad
4 5
OverDryve
™
Pro II Quick Start GuideOverDryve
™
Pro II Quick Start Guide
Home
Volume
Down Up
Power
Your OverDryve
™
Pro IIInstall the Mount
NOTE: Follow all local laws and regulations governing the placement of the mount.
1. Select an area with a line of sight to the sky and GPS satellites.
2. Clean and dry the mounting area.
3. Remove the suction cup protective film.
4. Attach the two pieces of the mount together and lock into place.
5. Adjust the angle of the mount.
6. Pull the suction cup lever up to release suction.
7. Plug the power cord into the mount and the
vehicle’s 12-volt power source.
8. Place and hold the mount suction cup against the
mounting surface.
9. Press the suction cup lever down until it snaps
into place.
10. Snap the tablet onto the mount.
11. Adjust the tablet so that it can be easily seen
and does not block the driver's line of sight.
USB
AUX out
DC in
(power)
Micro HDMI
(video out)
Micro USB
(power)
Micro SD card
Reset
AUX out
OverDryve
™
Pro II
SiriusXM
®
smart mount
FM
Transmitter
Antenna
SiriusXM
Antenna
6 7
OverDryve
™
Pro II Quick Start GuideOverDryve
™
Pro II Quick Start Guide
Getting Started
1. Connect to the Internet.
Connect to the Wi-Fi hotspot on your smartphone or to your
Wi-Fi network.
2. Register your device with Rand McNally for updates and support.
3. Connect to Bluetooth.
Enable Bluetooth on your smartphone and pair with
OverDryve
™
Pro to use Bluetooth hands-free calling and
texting, voice assistant, and music streaming.
4. Connect to your truck stereo system.
To stream audio to your truck stereo system, the tablet must be in
truck mode. To put the tablet in truck mode, place it on the smart
mount and plug the mount into the power adapter. You can listen
to audio through any of the following three methods:
1. Plug an AUX cable into the smart mount and the AUX input port in your truck.
NOTE: The AUX cable must be plugged into the smart mount, not OverDryve
™
Pro.
2. Use the smart mount speaker.
3. Use the FM Transmitter. To use the FM transmitter, attach the antenna to the smart mount.
On OverDryve
™
, tap Entertainment > FM Transmitter.
NOTE: If your truck does not include an AUX input port, visit randmcnally.com/aux-install to learn
about installation options..
OverDryve
™
Pro II Operating System Home Screen
2
4
1
3
5
6
987 10
1
Bluetooth indicator
2
Wi-Fi indicator
3
Battery power indicator
4
Current time
5
View installed apps
6
Swipe right to view additional home screens
7
Voice Assistant
8
Back
9
Home
10
View open apps
8 9
OverDryve
™
Pro II Quick Start GuideOverDryve
™
Pro II Quick Start Guide
Features
Bluetooth
®
Hands-Free Calling & Texting
Connect to your phone so you can call and text safely, hands-free.
Incoming text messages display in large, readable format. Your
contacts and call history will automatically download when you get
in the car.
Voice Assistant
Integrates with your phone's built-in voice assistant (Siri, Google,
etc.) so you can use the voice commands you're already used to.
Read and send text messages, place hands-free calls, set reminders,
and much more.
Music Streaming
Stream music, podcasts, and audiobooks directly from OverDryve
™
Pro or your phone; or download and play offline from OverDryve
™
Pro. Still have a library of MP3 files? Load them onto OverDryve
™
Pro using an SD card or USB and take your music with you.
Connect to the Truck Stereo
All audio from OverDryve
™
Pro can be played through the stereo of
any truck by connecting an AUX cable or streaming to the FM Radio.
OverDryve
™
also includes a powerful speaker in the smart mount.
Want an AUX input added to your car? Visit randmcnally.com/aux-
install to learn more.
ELD-Ready
Record, view and track duty status using Rand McNally
DriverConnect. Just add a Rand McNally ELD device and pair it with
OverDryve Pro. Also includes HOS timers, vehicle inspection reports
and more.
Navigation On-board
No need to use your phone's data plan when you need maps &
directions. OverDryve
™
Pro is equipped with high-accuracy GPS and
Rand McNally’s award-winning navigation.
Dash Cam
The dash cam records video of the road ahead. Provide
documentation of an accident and capture video mementos from the
road.
OverDryve
™
Pro OS
OverDryve
™
Pro runs on a custom operating system, OverDryve
™
Pro OS, built on top of Android 5.1 (Lollipop) – offering proprietary
Rand McNally apps as well as the customizability and familiarity
of Android. Access third party app stores where you can download
thousands of popular Android apps, games, and more.
SiriusXM
®
Enjoy the widest variety of ad-free music, plus talk, sports,
comedy and news 24/7.
Restart Your OverDryve
™
Pro II
Rand McNally has designed OverDryve
™
Pro for speed and reliability. However, from time to time, Android
devices may run into problems. If your unit becomes unresponsive for any reason, it’s always best to restart
the unit by turning it off and on again.
Restarting the Device
1. Hold down the power button for 3 seconds, or until you see the Power Off screen.
2. Press Power Off.
3. Once the unit has shut down, press and hold the power button for 2 to 4 seconds to turn it back on.
If the unit is unresponsive and you don’t see the power down button appear on the screen, hold down the
power button for 10 to 15 seconds and the device will turn off completely. Once the unit has shut off, press
and hold the power button for 2 to 4 seconds to turn it back on.
For additional help and FAQs, visit randmcnally.com/support.
10 11
OverDryve
™
Pro II Quick Start GuideOverDryve
™
Pro II Quick Start Guide
More Information
For more information
• Rand McNally Website
randmcnally.com/overdryve
• Support
randmcnally.com/support
• Accessories
store.randmcnally.com
• Facebook
facebook.com/randmcnally
VIP Customer Support
Call toll-free:
877-446-4863
E-mail:
support@randmcnally.com
Questions about using OverDryve
™
Pro II?
Our team is ready to help.
SiriusXM
®
To receive the SiriusXM signal you will need to install the provided
antenna. SiriusXM satellites are located over the equator and the
antenna must be mounted in a location that has a unobstructed view
to the south. Please avoid placing the antenna under or directly next
to metal or other dense materials as it may result in signal loss.
To activate your SiriusXM subscription, please power on your OverDryve
™
Pro
and launch the SiriusXM app. You should hear audio on the Preview
Channel (channel 1). If you do not hear audio, you need to adjust your
location or move the antenna so that it has as a clear view of the sky.
You will need your Radio ID, which can be found by tuning to Channel
0, or by looking at the sticker on the smart mount. The Radio ID does
not contain the letter I,O, S or F.
In the U.S., you can activate online or by calling
SiriusXM Listener Care:
• Visit siriusxm.com/activatenow
• Call SiriusXM Listener Care at 1-866-635-2349
For Canadian Subscriptions, please contact:
• Visit www.siriusxm.ca/activate
• Call SiriusXM Customer Care at 1-888-539-7474
SiriusXM
®
antenna
Smart mount
Note, the activation process usually takes 10 to 15 minutes, but may
take up to an hour. Your OverDryve
™
Pro will need to be powered on
and receiving the SiriusXM signal to receive the activation message.
12 13
OverDryve
™
Pro II Quick Start GuideOverDryve
™
Pro II Quick Start Guide
Warnings, End-User License Agreement, and Warranty
Pay attention to road conditions and street signs, and obey all traffic and safety laws. Traffic laws and current traffic conditions must always be observed and take precedence over the instructions issued by the Rand McNally
®
navigation system. The User should be aware of situations where current traffic conditions and the instructions from the navigation system may be in conflict. Some states prohibit the use of windshield mounts and may
otherwise restrict the usage of navigation and other electronic devices in the vehicle. It is the User’s responsibility to operate his/her vehicle in a safe manner and to ensure compliance with all laws and regulations. The use of
the navigation system does not relieve the User of his/her responsibilities while operating the vehicle.
If after reading the following terms and conditions, the User decides not to accept the terms, the User should not use this navigation system.
Rand McNally hereby grants you (“User”) a single-user non-exclusive, non-transferable license to use the Rand McNally navigation system, including software and associated data incorporated therein and all related
documentation that accompanies the product (hereinafter referred to as the “Product” ) for User’s own internal business or personal use and not for resale or sublicense.
This Product is furnished under license and may be used only in accordance with the terms and conditions of this license. Except as permitted by such license, the contents of this Product may not be disclosed to third parties,
copied or duplicated in any form, in whole or in part, without the prior written permission of Rand McNally. This Product contains proprietary and confidential information of Rand McNally and its licensors. Rand McNally grants
User a limited license for use of this Product for its normal operation. By using the Product, User acknowledges that the contents of the Product are the property of Rand McNally and its licensors and are protected by U.S.
copyright, trademark and patent laws and international treaties.
THE USER MAY NOT:
• Use the Product on a network or server, for time-sharing or to process data for other persons.
• Use the Product to create any routing tables, databases or other compendiums.
• Copy, loan or otherwise transfer or sublicense the Product, its software or content.
• Modify or adapt the Product in any way, or decompile, disassemble, reverse engineer or reduce to human readable form the software incorporated in the Product.
• Alter, remove or obscure any copyright notice, trademark notice, or proprietary legend from the Product.
This license will terminate automatically if User fails to comply with any of the terms of this license, and in such case, User agrees to immediately stop using the Product. Rand McNally may revise or update the Product at its sole
discretion, but it is not obligated to furnish any revisions or updates to User.
RM Acquisition, LLC d/b/a Rand McNally warrants that the Product, and the component parts thereof, will be free of defects in workmanship and materials for a period of one (1) year from the date of purchase. This warranty
may be enforced only by the first consumer purchaser (“Customer”), provided that the product is utilized within the U.S.A. or Canada.
During the warranty term, Rand McNally will, without charge, repair or replace (with a new or newly reconditioned unit), at its option, defective Products or component parts. For repair or replacement of defective Products,
Customer must contact Rand McNally at 1-877-446-4863 for return authorization and instructions. Customer will be required to provide proof of date of first Customer purchase by providing a copy of the original sales receipt
for the warranty to be valid. The Customer must pay any initial shipping charges required to ship the Product to Rand McNally for warranty service, but the return charges will be at Rand McNally’s expense, if the Product is
found to be defective and is repaired or replaced under the terms of this warranty.
Customer will be required to provide proof of date of first Customer purchase from a Rand McNally-authorized retailer, such as a duplicate copy of the original sales receipt, for the warranty to be valid.
If the Product sent in is still under its original warranty, then following repair or replacement by Rand McNally, the new warranty is 90 days or to the end of the original one (1) year warranty, whichever is longer. If the Product is
out of warranty, Rand McNally shall have no obligation to repair or replace the Product, but if it does choose to repair or replace the Product, such repair or replacement shall be at Rand McNally’s then-current cost. In such case,
customer shall be responsible for all shipping charges associated with the shipment of the Product to Rand McNally and its return to the customer.
This warranty gives the Customer specific rights. Other rights may be available to Customer which vary from state to state.
Exclusions: This limited warranty does not apply: 1) to any Product damaged by accident; 2) in the event of misuse or abuse of the Product or as a result of unauthorized alterations or repairs; 3) if the serial number has been
altered, defaced or removed; 4) if the Product is used other than as provided in the documentation that accompanies the Product, or 5) if the owner of the Product resides outside of the U.S.A. or Canada.
Rand McNally and the globe logo are registered trademarks, and OverDryve is a
trademark of RM Acquisition, LLC d/b/a Rand McNally.
SiriusXM and all related marks and logos are trademarks of SiriusXM Radio, Inc.
All rights reserved.
Local search information provided by Yelp.
Weather data provided by Foreca.
Fuel prices provided by Gasbuddy.
Traffic information provided by INRIX, Inc.
© 2020 Rand McNally. © 2020 HERE. All rights reserved.
Rand McNally follows a continuous improvement process and reserves the right to
provide enhancements that may not be reflected in the pictures and specifications
in this manual.
The information contained herein may be changed at any time without prior
notification. Neither this manual nor any parts thereof may be reproduced for any
purpose whatsoever without the express written consent of Rand McNally, nor
may it be transmitted in any form, either electronically or mechanically, including
photocopying and recording. All technical specifications, drawings, etc. are subject
to copyright law.
14 15
OverDryve
™
Pro II Quick Start GuideOverDryve
™
Pro II Quick Start Guide
NotesWarnings, End-User License Agreement, and Warranty
CAUTION: RAND MCNALLY MAKES NO WARRANTY AS TO THE ACCURACY OR COMPLETENESS OF THE INFORMATION IN THE PRODUCT, THE SOFTWARE OR THE DOCUMENTATION, AND DISCLAIMS
ANY AND ALL EXPRESS, IMPLIED OR STATUTORY WARRANTIES, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ANY WARRANTY AS TO
QUALITY, PERFORMANCE, TITLE OR NON- INFRINGEMENT. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO SOME CONSUMERS.
IN NO EVENT WILL RAND MCNALLY OR ITS LICENSORS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE
PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
IT IS THE USER’S RESPONSIBILITY TO USE THIS PRODUCT PRUDENTLY AND IN ACCORDANCE WITH THE DOCUMENTATION. THIS PRODUCT IS INTENDED TO BE USED ONLY AS A TRAVEL AID AND MUST NOT BE USED FOR ANY
PURPOSE REQUIRING PRECISE MEASUREMENT OF DIRECTION, DISTANCE, LOCATION OR TOPOGRAPHY.
The User agrees to allow information provided by the User to Rand McNally to be used for internal business evaluation purposes, including, but not limited to, evaluating the effectiveness of the Product and the services provided
and methods to simplify or improve User experiences. Such information will not be provided to third parties in any way that discloses the identity of the User.
Rand McNally may make use of third party software in the Product. Notwithstanding the terms and conditions of this license, use of some third party materials included in the Product may be subject to such third party’s terms
and conditions. The third party copyright notices are provided at the end of this License.
The User agrees to indemnify, defend and hold Rand McNally and its licensors (including their respective licensors, suppliers, assignees, subsidiaries, affiliated companies, and the respective of officers, directors, employees,
shareholders, agents and representatives of each of them) free and harmless from and against any liability, loss, injury (including injuries resulting in death), demand, action, cost, expense or claim of any kind or character,
including but not limited to attorney’s fees, arising out of or in connection with any use or possession by the User of this Product.
These terms and conditions constitute the entire agreement between Rand McNally (and its licensors and suppliers) and the User pertaining to the subject matter hereof, and supersedes in their entirety any and all written or
oral agreements previously existing between us with respect to such subject matter. The terms and conditions (including the license) may be updated from time to time with or without notice.
The above terms and conditions shall be governed by the laws of Illinois, without giving effect to (i) its conflict of laws provisions, or (ii) the United Nations Convention for Contracts for the International Sale of Goods, which is
explicitly excluded. The User agrees to submit to the jurisdiction of Illinois courts for any and all disputes, claims and actions arising from or in connection with the User’s license warranty and use of the Product hereunder.
User shall not export the Product in violation of any U.S. or foreign laws. Rand McNally’s licensors shall be third party beneficiaries of Rand McNally’s rights under this license, but are not parties hereto and have no obligations
hereunder.
By using this Product you agree to be bound both by the foregoing and to any additional terms of use found at www.randmcnally.com.
Actual toll costs may vary from estimates depending upon a number of factors including inaccurate or imprecise source data and variable toll costs, which are dependent upon vehicle characteristics (class, axle number, weight,
etc.) that vary across toll roads.
Restricted Rights Legend. For governmental agencies: Use, reproduction or disclosure is subject to restrictions set forth in subparagraph (c) (1) (iii) of the Right in Technical Data and Computer Software clause at
DFARS 52.227-7013, as amended.
Rand McNally, the globe logo, and TripMaker are registered trademarks and OverDryve is a trademark of RM Acquisition, LLC, d/b/a Rand McNally.
Portions © 2020 HERE. All rights reserved. This data includes information taken with permission from Canadian authorities, including © Her Majesty the Queen in Right of Canada, © Queen’s Printer for Ontario.
© 2020 Rand McNally. All rights reserved. U.S. Patent Nos. 7,580,791 and 8,214,141.
16
OverDryve
™
Pro II Quick Start Guide
Notes
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
