Electrolux ERF3867SOX Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur
ERF3867SOW
ERF3867SOX
................................................ .............................................
EN REFRIGERATOR USER MANUAL 2
FR RÉFRIGÉRATEUR NOTICE D'UTILISATION 24
CONTENTS
1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. DAILY USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4. HELPFUL HINTS AND TIPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5. CARE AND CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6. WHAT TO DO IF… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7. INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.
NOISES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9. TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10.
ENVIRONMENT CONCERNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
WE’RE THINKING OF YOU
Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with it
decades of professional experience and innovation. Ingenious and stylish, it has been designed
with you in mind. So whenever you use it, you can be safe in the knowledge that you’ll get great
results every time.
Welcome to Electrolux.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.electrolux.com
Register your product for better service:
www.electrolux.com/productregistration
Buy Accessories, Consumables and Original spare parts for your appliance:
www.electrolux.com/shop
CUSTOMER CARE AND SERVICE
We recommend the use of original spare parts.
When contacting Service, ensure that you have the following data available.
The information can be found on the rating plate. Model, PNC, Serial Number.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
2
www.electrolux.com
1.
SAFETY INFORMATION
In the interest of your safety and to ensure
the correct use, before installing and first
using the appliance, read this user manual
carefully, including its hints and warnings.
To avoid unnecessary mistakes and acci-
dents, it is important to ensure that all
people using the appliance are thoroughly
familiar with its operation and safety fea-
tures. Save these instructions and make
sure that they remain with the appliance if
it is moved or sold, so that everyone using
it through its life will be properly informed
on appliance use and safety.
For the safety of life and property keep
the precautions of these user's instruc-
tions as the manufacturer is not responsi-
ble for damages caused by omission.
1.1 Children and vulnerable
people safety
This appliance is not intended for use
by persons (including children) with re-
duced physical, sensory or mental ca-
pabilities, or lack of experience and
knowledge, unless they have been giv-
en supervision or instruction concerning
use of the appliance by a person re-
sponsible for their safety.
Children should be supervised to en-
sure that they do not play with the ap-
pliance.
Keep all packaging well away from chil-
dren. There is risk of suffocation.
If you are discarding the appliance pull
the plug out of the socket, cut the con-
nection cable (as close to the appliance
as you can) and remove the door to
prevent playing children to suffer elec-
tric shock or to close themselves into it.
If this appliance featuring magnetic
door seals is to replace an older appli-
ance having a spring lock (latch) on the
door or lid, be sure to make that spring
lock unusable before you discard the
old appliance. This will prevent it from
becoming a death trap for a child.
1.2 General safety
WARNING!
Keep ventilation openings, in the appli-
ance enclosure or in the built-in structure,
clear of obstruction.
The appliance is intended for keeping
foodstuff, production of cold water, with
or without carbon dioxide and for bev-
erages in a normal household as ex-
plained in this instruction booklet.
If the gas cylinder is used for other pur-
poses than that intended or if it is filled
by an unauthorised person, all guaran-
tees automatically become null and
void.
Do not use a mechanical device or any
artificial means to speed up the thawing
process.
Do not use other electrical appliances
(such as ice cream makers) inside of re-
frigerating appliances, unless they are
approved for this purpose by the manu-
facturer.
Do not damage the refrigerant circuit.
The refrigerant isobutane (R600a) is
contained within the refrigerant circuit of
the appliance, a natural gas with a high
level of environmental compatibility,
which is nevertheless flammable.
During transportation and installation of
the appliance, be certain that none of
the components of the refrigerant cir-
cuit become damaged.
If the refrigerant circuit should become
damaged:
avoid open flames and sources of ig-
nition
thoroughly ventilate the room in
which the appliance is situated
It is dangerous to alter the specifica-
tions or modify this product in any way.
Any damage to the cord may cause a
short-circuit, fire and/or electric shock.
WARNING!
Any electrical component (power
cord, plug, compressor) must be
replaced by a certified service
agent or qualified service person-
nel to avoid hazard.
1.
Power cord must not be length-
ened.
ENGLISH 3
2.
Make sure that the power plug is
not squashed or damaged by the
back of the appliance. A squashed
or damaged power plug may over-
heat and cause a fire.
3.
Make sure that you can come to
the mains plug of the appliance.
4.
Do not pull the mains cable.
5.
If the power plug socket is loose,
do not insert the power plug. There
is a risk of electric shock or fire.
6.
You must not operate the appli-
ance without the lamp cover (if
foreseen) of interior lighting.
This appliance is heavy. Care should be
taken when moving it.
Do not remove nor touch items from
the freezer compartment if your hands
are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
Avoid prolonged exposure of the appli-
ance to direct sunlight.
Bulb lamps (if foreseen) used in this ap-
pliance are special purpose lamps se-
lected for household appliances use
only. They are not suitable for house-
hold room illumination.
1.3 Daily use
Do not put hot pot on the plastic parts
in the appliance.
Do not store flammable gas and liquid
in the appliance, because they may ex-
plode.
Appliance's manufacturers storage rec-
ommendations should be strictly ad-
hered to. Refer to relevant instructions.
1.4 Care and cleaning
Before maintenance, switch off the ap-
pliance and disconnect the mains plug
from the mains socket.
Do not clean the appliance with metal
objects.
Regularly examine the drain in the re-
frigerator for defrosted water. If neces-
sary, clean the drain. If the drain is
blocked, water will collect in the bottom
of the appliance.
1.5 Installation
For electrical connection carefully
follow the instructions given in
specific paragraphs.
Unpack the appliance and check if
there are damages on it. Do not con-
nect the appliance if it is damaged. Re-
port possible damages immediately to
the place you bought it. In that case re-
tain packing.
It is advisable to wait at least four hours
before connecting the appliance to al-
low the oil to flow back in the compres-
sor.
Adequate air circulation should be
around the appliance, lacking this leads
to overheating. To achieve sufficient
ventilation follow the instructions rele-
vant to installation.
Wherever possible the back of the
product should be against a wall to
avoid touching or catching warm parts
(compressor, condenser) to prevent
possible burn.
The appliance must not be located
close to radiators or cookers.
Make sure that the mains plug is acces-
sible after the installation of the appli-
ance.
Connect to potable water supply only (If
a water connection is foreseen).
1.6 Service
Any electrical work required to do the
servicing of the appliance should be
carried out by a qualified electrician or
competent person.
This product must be serviced by an
authorized Service Centre, and only
genuine spare parts must be used.
1.7 Environment Protection
This appliance does not contain
gasses which could damage the
ozone layer, in either its refrigerant
circuit or insulation materials. The
appliance shall not be discarded
together with the urban refuse and
rubbish. The insulation foam con-
tains flammable gases: the appli-
ance shall be disposed according
to the applicable regulations to
4
www.electrolux.com
obtain from your local authorities.
Avoid damaging the cooling unit,
especially at the rear near the heat
exchanger. The materials used on
this appliance marked by the sym-
bol
are recyclable.
2. CONTROL PANEL
1 2
3
4
5
6
10
11
9
7
8
1
Temperature button
2
Display
3
ON/OFF button
4
ShoppingMode button
5
Light/Filter reset button
6
High sparkling water
7
Low sparkling water
8
Paddle
9
Still cold water
10
ChildLock button
11
Mode button
It is possible to change predefined sound
of buttons to a loudly one by pressing to-
gether Mode button and Temperature
colder button for some seconds. Change
is reversible.
2.1 Display
AB
C
D
E
FG
H
I
J
ENGLISH 5
A)
ExtraHumidity mode
B)
Temperature indicator
C)
Water choice indicator
D)
Water circuit cleaning
E)
Alarm indicator
F)
Water filter indicator
G)
ChildLock mode
H)
ShoppingMode
I)
EcoMode
J)
HolidayMode
2.2 Switching on
To switch on the appliance do these
steps:
1.
Connect the mains plug to the power
socket.
2.
Press the ON/OFF button if the dis-
play is off.
3.
If DEMO appears on the display, the
appliance is in demonstration mode.
Refer to "What to do if..." paragraph.
4.
The temperature indicators show the
set default temperature.
To select a different set temperature refer
to "Temperature regulation".
2.3 Switching off
To switch off the appliance do these
steps:
1.
Press the ON/OFF button for 3 sec-
onds.
2.
The display switches off.
3.
To disconnect the appliance from the
power disconnect the mains plug
from the power socket.
2.4 Temperature regulation
The set temperature of the fridge may be
adjusted by pressing the temperature but-
ton.
Set default temperature: +4°C for the
fridge.
The temperature indicator shows the set
temperature.
The set temperature will be reached with-
in 24 hours.
After a power failure the set tem-
perature remains stored.
2.5 ChildLock mode
To lock any possible operation through
the buttons select the ChildLock mode.
Water dispensing and the light is not
locked in this mode.
To switch on the function:
1.
Press the ChildLock button for 3 sec-
onds.
2.
The ChildLock mode indicator is
shown.
To switch off the function:
1.
Press the ChildLock button for 3 sec-
onds.
2.
The ChildLock mode indicator goes
off.
2.6 HolidayMode
This function allows you to keep the re-
frigerator closed and empty during a long
holiday period without the formation of a
bad smell.
The fridge compartment must be
empty with holiday function on.
To switch on the function:
1.
Press the Mode button until the cor-
responding icon appears.
2.
After a few seconds The Holiday indi-
cator goes on.
The fridge temperature indicator
shows the set temperature.
To switch off the function:
1.
Press the Mode button until the cor-
responding icon appears.
2.
After a few seconds The Holiday indi-
cator goes off.
The function switches off by se-
lecting a different fridge set tem-
perature.
2.7 EcoMode
For optimal food storage select the Eco-
Mode.
To switch on the function:
1.
Press the Mode button until the cor-
responding icon appears.
2.
After a few seconds The EcoMode in-
dicator goes on.
The temperature indicator shows the
set temperature:
6
www.electrolux.com
for the fridge: +4°C
To switch off the function:
1.
Press the Mode button until the cor-
responding icon appears.
2.
After a few seconds The EcoMode in-
dicator goes off.
The function switches off by se-
lecting a different set temperature.
2.8 Extra Humidity Mode
If you need to increase the humidity in the
refrigerator, we suggest activating the Ex-
tra Humidity function.
To switch on the function:
1.
Press the Mode button until the cor-
responding icon appears.
2.
After a few seconds The Extra Hu-
midity indicator goes on.
To switch off the function:
1.
Press the Mode button until the cor-
responding icon appears.
2.
After a few seconds The Extra Hu-
midity indicator goes off.
2.9 ShoppingMode
If you need to insert a large amount of
warm food, for example after doing the
grocery shopping, we suggest activating
the ShoppingMode to chill the products
more rapidly and to avoid warming the
other food which is already in the refriger-
ator.
To switch on the function:
1.
Press the ShoppingMode button.
The ShoppingMode indicator ap-
pears.
The ShoppingMode shuts off automatical-
ly after approximately 6 hours.
To switch off the function before its auto-
matic end:
1.
Press the ShoppingMode button.
2.
The ShoppingMode indicator goes
off.
Alternative method:
To switch on the function:
1.
Press the Mode button until the cor-
responding icon appears.
After a few seconds the Shopping-
Mode indicator goes on.
To switch off the function before its auto-
matic end:
1.
Press the Mode button until the cor-
responding icon appears.
2.
After a few seconds the Shopping-
Mode indicator goes off.
The function switches off by se-
lecting a different fridge set tem-
perature.
2.10 Door open alarm
An acoustic alarm will sound if the door is
left open for a few minutes. The door
open alarm conditions are indicated by:
flashing Alarm indicator
acoustic buzzer
When normal conditions are restored
(door closed), the alarm will stop.
During the alarm, the buzzer can be
switched off by pressing any button.
2.11 Selecting and dispensing
water
Before dispensing water, select either
Still cold water, Low sparkling water or
High sparkling water.
The actual choice is indicated by the in-
dicator.
Water is dispensed by pressing a glass
or other container towards the flap.
Draw back the glass or container to
stop the water flow and the indicator
goes off after a few seconds.
Any water that drips or is spilled is collec-
ted in the drip tray below the water dis-
penser. The drip tray can be detached
and emptied when necessary.
2.12 Lighting
The water dispenser lighting illuminates
automatically when water is dispensed.
2.13 For continuous lighting
1.
Press the Light button and the lighting
goes on.
Brightness is now about 20% until the
dispenser is used.
2.14 Switch off the lighting
1.
Press the Light button and the lighting
goes out.
ENGLISH 7
2.15 Water filter indicator
When the water filter indicator lights up
the water filter has about 20% remaining
lifetime. In this situation, it is recommen-
ded that you buy a replacement filter.
When the water filter indicator starts flash-
ing, the water filter lifetime is consumed .
Replace the water filter without delay, re-
fer to "Installation of the water filter".
When the water filter is replaced. Press
the Filter reset button for 3 seconds to re-
set the water filter indicator.
2.16 Water circuit cleaning
If you need to clean the water system.
1.
Press the Mode button until the cor-
responding icon appears.
2.
After a few seconds the Water circuit
cleaning and the Still cold water indi-
cator goes on.
Water select locked into Still cold wa-
ter.
3.
Dispensing water in total 2 minutes.
The water system is cleaned.
4.
The Water circuit cleaning and the
Still cold water indicator goes off.
To switch off the function before its auto-
matic end:
1.
Press the Mode button until the cor-
responding icon appears.
2.
After a few seconds the Water circuit
cleaning and the Still cold water indi-
cator goes off.
3. DAILY USE
3.1 Use of the fridge
compartment
The temperature of this compartment may
be regulated between +2°C and +8°C.
During normal functioning the indicator
shows the set temperature.
A medium setting is generally the
most suitable.
The exact setting should be chosen keep-
ing in mind that the temperature inside the
appliance depends on:
room temperature
how often the door is opened
the quantity of food stored
the location of the appliance.
If the ambient temperature is high
or the appliance is fully loaded,
and the appliance is set to the
lowest temperatures, it may run
continuously causing frost to form
on the rear wall. In this case the
Temperature regulator must be
set to a higher temperature to al-
low automatic defrosting and
therefore reduced energy con-
sumption.
3.2 Taste Guard Filter
Your appliance is equipped with a carbon
filter behind the air lever flap.
The filter purifies the air from unwanted
odours in the fridge compartment pre-
serving food quality.
On delivery the filter is in a plastic bag.
Refer to "Installation of the Taste Guard
filter" for instructions.
Make sure that the air lever flap is
closed to obtain proper function.
3.3 Vegetable Drawer
The drawer is suitable for storing fruit and
vegetables.
Some models have a separator inside the
drawer that can be placed in different po-
sitions to allow for the subdivision best
suited to personal needs.
All parts inside the drawer can be re-
moved for cleaning purposes.
8
www.electrolux.com
3.4 Movable shelves
A
The walls of the refrigerator are equipped
with a series of shelves support so that
the shelves can be positioned as desired.
Some shelves must be lifted up by the
rear edge to enable them to be removed.
The shelf (A) above the water
module is recommended to be
placed as shown for good air cir-
culation.
Do not move the glass shelf
above the vegetable drawer to en-
sure correct air circulation.
3.5 Bottle rack
Place the bottles (with the opening facing
front) in the pre-positioned shelf.
If the shelf is positioned horizon-
tally, place only closed bottles.
This bottle holder shelf can be tilted in or-
der to store previously opened bottles. To
obtain this result, pull the shelf up so it
can rotate upwards and be placed on the
next higher level.
3.6 Positioning the door shelves
To permit storage of food packages of
various sizes, the door shelves can be
placed at different heights.
To make these adjustments proceed as
follows:
Gradually pull the shelf in the direction of
the arrows until it comes free, then reposi-
tion as required.
Do not move the big lower door
shelf to ensure correct air circula-
tion.
ENGLISH 9
3.7 Cleaning the interior
Before using the appliance for the first
time, wash the interior and all internal ac-
cessories with lukewarm water and some
neutral soap so as to remove the typical
smell of a brand-new product, then dry
thoroughly.
Do not use detergents or abrasive
powders, as these will damage
the finish.
Check that the drain hose at the rear of
the cabinet discharges into the drip tray
4. HELPFUL HINTS AND TIPS
4.1 Hints for energy saving
Do not open the door frequently or
leave it open longer than absolutely
necessary.
Place the shelf above the water module
as described in chapter “Daily use”.
If the ambient temperature is high and
the Temperature Regulator is set to low
temperature and the appliance is fully
loaded, the compressor may run con-
tinuously, causing frost or ice on the
evaporator. If this happens, set the
Temperature Regulator toward warmer
settings to allow automatic defrosting
and so a saving in electricity consump-
tion.
4.2 Hints for fresh food
refrigeration
To obtain the best performance:
do not store warm food or evaporating
liquids in the refrigerator
do cover or wrap the food, particularly if
it has a strong flavour
position food so that air can circulate
freely around it
4.3 Hints for refrigeration
Useful hints:
Meat (all types) : wrap in polythene bags
and place on the glass shelf above the
vegetable drawer.
For safety, store in this way only one or
two days at the most.
Cooked foods, cold dishes, etc..: these
should be covered and may be placed on
any shelf.
Fruit and vegetables: these should be
thoroughly cleaned and placed in the spe-
cial drawer(s) provided.
Butter and cheese: these should be
placed in special airtight containers or
wrapped in aluminium foil or polythene
bags to exclude as much air as possible.
Milk bottles: these should have a cap and
should be stored in the bottle rack on the
door.
Bananas, potatoes, onions and garlic, if
not packed, must not be kept in the re-
frigerator.
4.4 Hints for temperature inside
the fridge
A suitable temperature inside the fridge
is approx. +4° C. When the tempera-
ture regulator is set to +4° C this repre-
sents the mean temperature in the
fridge. It is normal with higher tempera-
ture in the top of the fridge. If the tem-
perature regulator is set to a cold tem-
perature, the ambient temperature is
high or if the fridge is fully loaded the
compressor will run for a longer time. If
10
www.electrolux.com
too cold, change to a higher tempera-
ture setting.
Do not place food against or close
to the temperature sensor (A).
This can result in too cold temper-
atures.
A
If you want to check the temperature of
food stored in the refrigerator, place a
glass of water centrally in the cabinet,
and put a proper thermometer with an
accuracy of +/– 1 °C into it. After 6
hours the temperature can be moni-
tored. The measuring shall be per-
formed under steady-stated conditions
(without changing the load).
5. CARE AND CLEANING
CAUTION!
Unplug the appliance before car-
rying out any maintenance opera-
tion.
This appliance contains hydrocar-
bons in its cooling unit; mainte-
nance and recharging must there-
fore only be carried out by author-
ized technicians.
5.1 Periodic cleaning
The equipment has to be cleaned regular-
ly:
clean the inside and accessories with
lukewarm water and some neutral
soap.
regularly check the door seals and wipe
clean to ensure they are clean and free
from debris.
rinse and dry thoroughly.
Do not pull, move or damage any
pipes and/or cables inside the
cabinet.
Never use detergents, abrasive
powders, highly perfumed clean-
ing products or wax polishes to
clean the interior as this will dam-
age the surface and leave a
strong odor.
Clean the condenser (black grill) and the
compressor at the back of the appliance
with a brush. This operation will improve
the performance of the appliance and
save energy consumption.
Take care of not to damage the
cooling system.
When moving the cabinet, lift it by
the front edge to avoid scratching
the floor.
Many proprietary kitchen surface cleaners
contain chemicals that can attack/dam-
age the plastics used in this appliance.
For this reason use a soft cloth rinsed in
warm water and neutral soap emulsion for
cleaning external surfaces.
Do not use detergents or abrasive
paste as these will damage the
paint, or stainless steel anti finger
print coating.
After cleaning, reconnect the equipment
to the mains supply.
5.2 Replacing the Taste Guard
filter
To get the best performance the Taste
Guard filter once every year.
New active filters can be purchased from
your local dealer.
Refer to "Installation of the Taste Guard
filter" for instructions.
ENGLISH 11
5.3 Replacing the water filter
Remove the filter. A small amount of wa-
ter will run out. Dry off and fit the new fil-
ter.
Refer to "Installation of the water filter".
Replacement filters can be ordered from
Electrolux Service Force Centre.
The water connection does not
need to be switched off when
changing the filter.
5.4 Replacing the gas cylinder
Remove the gas cylinder, refer to "Installa-
tion of the gas cylinder".
The replacement gas cylinder is obtained
through your local dealer.
5.5 Cleaning the water
dispenser
When necessary, clean the surfaces of
the dispenser, using only a soft cloth and
warm water.
The dispenser drip tray can be cleaned
with a lukewarm water and some neutral
soap. Lime deposits on the dispenser sur-
face can removed using vinegar or diluted
acetic acid as cleaning agent. Wipe clean
with a damp cloth.
5.6 Defrosting the refrigerator
Frost is automatically eliminated from the
evaporator of the refrigerator compart-
ment every time the motor compressor
stops, during normal use. The defrost wa-
ter drains out through a drain hole into a
special container at the back of the appli-
ance, over the motor compressor, where
it evaporates.
5.7 Periods of non-operation
When the water system is not use for a
long period, turn off the water connection
to the refrigerator.
A filter that has been in service shall not
be exposed to temperatures below 0°C
as cracking of the filter body may occur
due to freezing expansion.
If the filter still is to be preserved for lat-
er reuse, suitable storage temperature
will be +5°C.
When the appliance is not in use for long
periods, take the following precautions:
1.
disconnect the appliance from elec-
tricity supply
2.
remove all food
3.
clean the appliance and all accesso-
ries
4.
leave the door/doors open to prevent
unpleasant smells.
Before using the appliance again, rinse
the system thoroughly by dispensing at
least three liters (5 pints) of water.
If necessary, the system can be
cleaned by using a sanitizing kit which
can be ordered through Electrolux
Service Force Centre or through our
website www.electrolux.com.
If the cabinet will be kept on, ask
somebody to check it once in a
while to prevent the food inside
from spoiling in case of a power
failure.
5.8 Cleaning the ventilation grille
The ventilation grille can be removed for
washing.
Make sure the door is open and then:
Loosen the upper edge of the grille by
pulling outward/downward.
Pull the grille straight out to completely
remove it.
Vacuum clean under the cabinet.
12
www.electrolux.com
6. WHAT TO DO IF…
During operation of the appliance some
smaller but annoying trouble can often oc-
cur, which does not require calling a tech-
nician out. In the following chart informa-
tion is given about them to avoid unnec-
essary charges on service.
The operation of the appliance
goes with certain sounds (com-
pressor and circulating sound).
This not means a trouble, but a
normal operation.
The appliance operates discontin-
uously, so the stopping of com-
pressor does not mean being no
current. That is why you must not
touch the electrical parts of the
appliance before breaking the cir-
cuit.
Problem Possible cause Solution
The appliance is
noisy.
The appliance is not sup-
ported properly.
Check if the appliance
stands stable (all feet and
wheels should be on the
floor). Refer to "Levelling".
The buzzer sounds.
The Alarm icon
flashing.
The door is not closed
correctly.
Refer to "Door open alarm".
Upper or lower
square is shown in
the temperature dis-
play.
An error has occurred in
measuring the tempera-
ture
Call your service represen-
tative (the cooling system
will continue to keep food
products cold, but temper-
ature adjustment will not be
possible)
The compressor
runs continuously.
The Temperature regulator
may be set incorrectly.
Set a warmer temperature.
The door is not closed
correctly.
Refer to "Closing the door".
The door has been
opened too frequently.
Do not keep the door open
longer than necessary.
The food temperature is
too high.
Let the food temperature
decrease to room tempera-
ture before storage.
The room temperature is
too high.
Decrease the room temper-
ature.
Water flows inside
the refrigerator.
The water outlet is clog-
ged.
Clean the water outlet.
Food prevent that water
flows into the water collec-
tor.
Make sure that food do not
touch the rear plate.
Water flows on the
ground.
The melting water outlet
does not flow in the evap-
orative tray above the
compressor.
Attach the melting water
outlet to the evaporative
tray.
ENGLISH 13
Problem Possible cause Solution
The temperature in
the appliance is too
cold.
The Temperature regulator
may be set incorrectly.
Set a warmer temperature.
The temperature in
the appliance is too
warm.
The Temperature regulator
may be set incorrectly.
Set a lower temperature.
The door is not closed
correctly.
Refer to "Closing the door".
The food temperature is
too high.
Let the food temperature
decrease to room tempera-
ture before storage.
The temperature in
the refrigeration is
too warm.
There is no cold air circu-
lation in the appliance.
Make sure that there is cold
air circulation in the appli-
ance.
Large quantities of food to
be cooled were put in at
the same time.
Insert smaller quantities of
food to be cooled at the
same time.
The appliance does
not operate.
The appliance is switched
off.
Switch on the appliance.
The mains plug is not con-
nected to the mains sock-
et correctly.
Connect the mains plug to
the mains socket correctly.
The appliance has no
power. There is no voltage
in the mains socket.
Connect a another electrical
appliance to the mains
socket. Check fuse. Con-
tact a qualified electrician.
Not enough carbon
dioxide in the water.
The carbon dioxide is run-
ning out.
Refer to "Installation of the
gas cylinder".
Too much carbon
dioxide in the water.
Dilute with ordinary water. Refer to "Selecting and dis-
pensing water".
No carbon dioxide. The gas cylinder is empty. Refer to "Replacing gas cyl-
inder"
No or very low water
flow.
The gas cylinder is empty. Refer to "Replacing gas cyl-
inder".
Sediment in the water. Remove and clean the
strainer in the inlet hose
connection.
Water supply obstructed. Check water supply.
Only gas comes out
when dispensing
carbonated water.
Sediment in the water. Remove and clean the
strainer in the inlet hose
connection.
The water filter indi-
cator flashes.
The filter has been totally
consumed.
Refer to "Replacing the wa-
ter filter".
14
www.electrolux.com
Problem Possible cause Solution
The water filter indi-
cator lights con-
stantly.
20% of filter capacity re-
mains.
Buy a new filter.
The Water circuit
cleaning and Still
cold water indicator
is shown.
No water has been dis-
pensed in 10 days.
Dispense water in total 2
minutes and the icons goes
off.
The buzzer sounds.
The Alarm icon and
ExtraHumidity icon
flashing.
Failed water supplies. Press any button to reset
the alarm.
Select Still cold water and
push the paddle and re-
lease.
The water pump start and
filling the water system.
After a few minutes the
icons goes off.
Dispensing water more
than 2 minutes
Release the Paddle and
press any button to reset
the alarm.
Start new dispensing.
The lamp does not
work.
The door has been open
to long.
Close the door.
The lamp is defective. Refer to "Replacing the
lamp".
Door interferes with
ventilation grill.
The appliance is not level-
led.
Refer to "Levelling".
Misaligned door.
The appliance is not level-
led.
Refer to "Levelling".
DEMO appears on
the Display.
The appliance is in dem-
onstration mode (DEMO)
Keep pressed approximate-
ly 10 sec the Mode button
since a sound of buzzer is
heard and the Display shut
off for a short while: appli-
ance start works regularly.
As much as the advice does not lead to result, call the nearest brand-mark service.
6.1 Replacing the lamp
The appliance is equipped with a longlife
LED interior light.
Only service is allowed to replace the
lighting device. Contact your Service Cen-
ter .
6.2 Closing the door
1.
Clean the door gaskets.
2.
If necessary, adjust the door. Refer to
"Installation".
3.
If necessary, replace the defective
door gaskets. Contact the Service
Center.
ENGLISH 15
7. INSTALLATION
WARNING!
Read the "Safety Information"
carefully for your safety and cor-
rect operation of the appliance
before installing the appliance.
7.1 Positioning
Install this appliance at a location where
the ambient temperature corresponds to
the climate class indicated on the rating
plate of the appliance:
Cli-
mate
class
Ambient temperature
SN +10°C to + 32°C
N +16°C to + 32°C
ST +16°C to + 38°C
T +16°C to + 43°C
7.2 Location
50 mm
To ensure best performance, if the appli-
ance is positioned below an overhanging
wall unit, the minimum distance between
the top of the cabinet and the wall unit
must be at least 40 mm. Ideally, however,
the appliance should not be positioned
below overhanging wall units.
The ventilation space can be:
directly above the appliance
behind and above the top cupboard.
In this case, the space behind the top
cupboard must be at least 50 mm
deep.
7.3 Electrical connection
Before plugging in, ensure that the volt-
age and frequency shown on the rating
plate correspond to your domestic power
supply.
The appliance must be earthed. The pow-
er supply cable plug is provided with a
contact for this purpose. If the domestic
power supply socket is not earthed, con-
nect the appliance to a separate earth in
compliance with current regulations, con-
sulting a qualified electrician.
The manufacturer declines all responsibili-
ty if the above safety precautions are not
observed.
This appliance complies with the E.E.C.
Directives.
16
www.electrolux.com
7.4 Removing the transport support
2
3
Your appliance is equipped with transport
support to secure the door during trans-
portation.
To remove them do these steps:
Open the door.
Remove the transport support from the
door sides.
Remove the transport support from the
lower hinge (some models).
Some models are fitted with a si-
lencing pad under the cabinet. Do
not remove this pad.
7.5 Rear spacers
Install the spacers provided within the
accessory bag as shown in the figure.
Install the spacers on the brackets of
the condenser (black grill) at the back of
the appliance.
7.6 Connecting the water hose.
Water supply should be provided with a
tap and 3/4" male connector within 1,5 m
from the appliance.
This work is to be carried out by a skilled
plumber.
There are different type-approved taps
and tap assemblies on the market.
The water hose must not be cracked,
squeezed or put in tight bends.
The safety valve provided in a package in-
side the appliance should be used to pre-
vent overflow.
Before the safety valve is placed on the
tap, turn the pointer counter clockwise to
number 10 with the enclosed plastic key.
Install the safety valve on the tap and let
at least 10 litres of water flow through the
device.
Before connecting the appliance turn the
pointer to number 1 on the safety valve.
If the safety valve has shut off, detach it
and press the red plunger which is loca-
ted inside the lower housing of the device
itself.
Before the appliance is placed in final lo-
cation, ensure that the water connection
has been correctly carried out and that
ENGLISH 17
there is no leakage at the connection to
the water tap.
Tighten the screw enough by hand.
Make sure that the gasket is properly
positioned in the connector.
We recommend that the appliance is
placed on a "run-off" mat intended for re-
frigerators and freezers, which makes it
easier to detect possible leakage.
7.7 Levelling
When placing the appliance ensure that it
stands level. If necessary adjust the feet
using the adjustment spanner supplied.
7.8 Installation of the Taste Guard filter
The Taste Guard filter is an active carbon
filter which absorbs bad odors maintain
the best flavour and aroma for all food-
stuffs without risk of odor cross contami-
nation.
On delivery the carbon filter is in a plastic
bag to preserve performance.
Open the air lever flap.
Take the filter out of the plastic bag.
Insert the filter in the slot found in the
back of the air lever flap.
Close the air lever flap.
The filter should be handled care-
fully so fragments do not loosen
from the surface.
Make sure that the air lever flap is
closed to obtain proper function.
7.9 Starting the water system
for the first time.
Ensure proper connection to the water
supply, refer to "Connecting the water
hose".
1.
Open the tap on the water connec-
tion.
2.
Start the refrigerator.
The water system main valve opens and
the pump starts to fill the system.
18
www.electrolux.com
7.10 Installation of the water filter
1
2
Unpack the filter.
Remove the accessories in front of the
water module and open the service
hatch.
Place a cloth or a piece of kitchen towel
in the space beneath the water filter.
Pull the bypass cartridge outwards,
grasping the lower part, until the water
bypass cartridge is automatically ejec-
ted.
Remove the protective wrapping of the
new water filter and insert the new filter
firmly into the filter connection.
Push the water filter back to its original
position.
Remove cloth or towel and make sure
that spilled water is wiped off.
Close the hatch and remount the interi-
or.
Keep the bypass cartridge for future
use.
Select Still cold water and dispense
about 2 litres of water. There may be
some air to start with.
7.11 Installation of the gas cylinder
Remove the gas cylinder wrapping and
screw on the adapter to the gas cylin-
der. Tighten by hand only.
ENGLISH 19
1
2
Position the gas cylinder with the
adapter attached underneath the valve
and ensure that the hooks of the lever
system supports the protruding parts of
the adapter.
3
4
Then turn the lever upwards in one
continuous movement.
7.12 Door reversibility
In case you want to change the opening
direction of the door, contact the nearest
After Sales Service Force. The After Sales
Service specialist will carry out the reversi-
bility of the doors at your cost.
8. NOISES
There are some sounds during normal
running (compressor, refrigerant circula-
tion).
BRRR!
HISSS!
CLICK!
BLUBB!
CRACK!
SSSRRR!
OK
20
www.electrolux.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Electrolux ERF3867SOX Manuel utilisateur

Catégorie
Frigos
Taper
Manuel utilisateur

dans d''autres langues