Cafe GDF650SGJ0BB Le manuel du propriétaire

Catégorie
Lave-vaisselle
Taper
Le manuel du propriétaire
Write the model and serial
numbers here:
Model # _________________
Serial # _________________
You can find them on the tub wall,
just inside the door.
GE is a trademark of the General Electric Company. Manufactured under trademark license.
OWNER’S MANUAL
DISHWASHERS
49-55102-2 05-17 GEA
SAFETY INFORMATION .........2
OPERATING INSTRUCTIONS
Getting Started ........................4
Using the Dishwasher ..................8
Appliance Communications ............ 11
Loading the Dishwasher ...............12
CARE AND CLEANING ............18
TROUBLESHOOTING TIPS ..... 20
WARRANTY ..................... 24
CONSUMER SUPPORT ..........23
Dishwashers
GDF 570-650 Series
GDT 655-695 Series
DDT 595 Series
PDF 820 Series
PDT 825-855 Series
CDT 835-865 Series
Includes GE®, GE Profile™
Series and GE Café™ Series
products
ENGLISH/FRANÇAIS/
ESPAÑOL
2
For your safety, the information in this manual must be followed to minimize the risk of fire,
explosion, electric shock, and to prevent property damage, personal injury, or death.
Use this appliance only for its intended purpose as
described in this Owner’s Manual.
Use only detergents or wetting agents
recommended for use in a dishwasher
and keep them out of reach of children.
Using a detergent that is not specifically
designed for dishwashers will cause the
dishwasher to fill with suds.
Locate sharp items so that they are not likely to damage the
door seal.
Load sharp knives with the handles up to reduce the risk of
cut-type injuries.
Do not wash plastic items unless marked dishwasher safe
or the equivalent. For plastic items not so marked, check the
manufacturer’s recommendations.
Do not touch the heating element during or immediately
after use.
Do not operate your dishwasher unless all enclosure
panels are properly in place.
Do not tamper with controls.
Do not abuse, sit on or stand on the door or dish rack of the
dishwasher.
To reduce the risk of injury, do not allow children to play with,
on or inside this appliance at any time.
Do not store or use combustible materials including gasoline
or other flammable liquids or vapors in the vicinity of this or any
other appliance.
Small parts, such as rack clips and filter retaining posts, can
be a choke hazard to small children if removed from the
dishwasher. Keep out of reach of small children.
PROPER INSTALLATION AND MAINTENANCE
This dishwasher must be properly installed and located in accordance with the Installation Instructions before it is used. If
you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by visiting our Website at
GEAppliances.com. In Canada, visit www.GEAppliances.ca.
Connect the dishwasher/appliance to a grounded metal,
permanent wiring system; or run an equipment-grounding
conductor with the circuit conductors and connect to the
equipment-grounding terminal or lead of the appliance.
Improper connection of the equipment-grounding conductor
can result in a risk of electric shock. Check with a qualified
electrician or service representative if you are in doubt
whether the appliance is properly grounded.
Dispose of discarded appliances and shipping or packing
material properly.
Do not attempt to repair or replace any part of your
dishwasher unless it is specifically recommended in this
manual. All other servicing should be referred to a qualified
technician.
Use only cord kit WX09X70910 or hard-wire to building
electrical. Failure to follow this instruction, could result in risk of
fire and personal injury.
To minimize the possibility of electric shock, disconnect this
appliance from the power supply before attempting any
maintenance.
NOTE: Turning the dishwasher off does not disconnect the
appliance from the power supply. We recommend having
a qualified technician service your appliance.
WARNING
WARNING
When using your dishwasher, follow basic precautions, including the following:
WARNING
IMPORTANT SAFETY INFORMATION
5($'$//,16758&7,216%()25(86,1*³
SAVE THESE INSTRUCTIONS
3
IMPORTANT SAFETY INFORMATION
5($'$//,16758&7,216%()25(86,1*³
SAVE THESE INSTRUCTIONS
GEAppliances.com
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
WATER HEATER SAFETY
Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two or more weeks.
HYDROGEN GAS IS EXPLOSIVE.
If the hot water has not been used for two or more weeks, prevent the possibility of damage or injury by turning on all hot
water faucets and allowing them to run for several minutes. Do this before using any electrical appliance connected to
the hot water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable,
do not smoke, use an open flame, or use the appliance during this process.
RISK OF CHILD ENTRAPMENT
PROPER DISPOSAL OF THE DISHWASHER
Junked or abandoned dishwashers are dangerous…even if they will sit for “just a few days.” If you
are getting rid of your dishwasher, please follow the instructions below to help prevent accidents.
Do not allow children to play with, on, or inside this or any discarded appliance.
Take off the door of the washing compartment or remove the latch by removing the two screws
from the latch receiver inside the tub (as shown).
Two screws
To prevent minor injury and property damage
During or after wash cycle, contents may be hot to the
touch. Use care before handling.
Close supervision is necessary if this appliance is used by
or near children. Do not allow children to play around the
dishwasher when closing the door, closing the upper rack,
or while vertically adjusting the upper rack due to the
possibility of small fingers being pinched.
Non-Dishware Items: Do not wash items such as
electronic air cleaner filters, furnace filters and paint
brushes in your dishwasher. Damage to the dishwasher
and discoloration or staining of the dishwasher may
result.
Load light-weight, plastic items so they do not become
GLVORGJHGDQGGURSWRWKHERWWRPRIWKHGLVKZDVKHU³
they might come into contact with the heating element
and be damaged.
This appliance must be supplied with 120V, 60 Hz, and
connected to an individual, properly grounded branch
circuit, protected by a 15 or 20 amp circuit breaker or
time-delay fuse.
If the electric supply provided does not meet the above
specifications, it is recommended that a licensed
electrician install an approved outlet.
Your dishwasher circuit should not be used for any other
appliance while the dishwasher is in operation as the
dishwasher requires the full capacity of the circuit.
ELECTRICAL REQUIREMENTS
If your dishwasher is connected to a wall switch,
ensure that the switch is on prior to use.
If you choose to turn the wall switch off between
wash cycles, allow 5-10 seconds after turning the
switch on before touching Start to allow the control
to initialize.
Use only powder, Cascade
®
Platinum ActionPacs
, liquid
detergents or rinse agents recommended for use in a
dishwasher and keep them out of the reach of children.
Cascade
®
Platinum ActionPacs
Automatic Dishwashing
Detergent, and Cascade
®
Platinum Rinse Aid
rinse agents
have been approved for use in all GE Appliances dishwashers.
NOTICE
WARNING
CAUTION
CAUTION
WARNING
4
Getting started!
Load Dishwasher
For best dishwashing results, follow the loading guidelines found in the Loading the dishwasher section. No pre-rinsing of normal
food soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove leafy vegetables, meat trimmings,
and excessive amounts of grease or oil.
Add Detergent
Add needed amount of detergent to the detergent dispenser. Use a detergent such as Cascade
®
Platinum ActionPacs
. See
Detergent Dispenser in the Using the dishwasher section.
Add Rinse Agent
Add Rinse Agent to the rinse agent dispenser. See Use a Rinse Agent in the Using the dishwasher section.
1
2
3
Features and appearance will vary throughout this manual
DDT595
GDT655, GDT695,
PDT825
PDT845, PDT855
GDF570
Steam
CDT835
CDT865
GDF650, PDF820
GEAppliances.com
5
Select Cycle
Press the Select Cycle button for the desired wash cycle. On some models, the light next to the Select Cycle button will be lit to
indicate which wash cycle has been selected. On other models, pressing the Select Cycle button will show various cycles in the
display window. Press the button until the desired cycle is shown.
NOTE: Actual cycle times vary based on soil level, water temperature, and options selected.
The cycle may be selected with the door in the open position. The cycle will not start until the Start button is pushed and the door is
closed within 4 seconds.
AutoSense
This cycle automatically senses the soil level and adjusts the wash cycle accordingly. *Time range: 1 hour 50
minutes - 2 hours 10 minutes.
Heavy This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on soils.
Everyday dishes are safe to be used in this cycle. *Time: 2 hours 31 minutes.
Normal
This cycle is meant for daily, regular, or typical use to completely wash a full load of normally soiled dishes and is
designed to conserve both water and energy. *Time range: 1 hour 15 minutes - 1 hour 50 minutes. NOTE: Normal
was used to rate the energy efficiency of this dishwasher.
Light
This cycle is for light to medium soiled dishes. It is safe for china and crystal with no options selected.
*Time: 55 minutes.
Rinse For rinsing partial loads that will be washed later. Do not use detergent. Detergent is not dispensed during the
(on some models) rinse cycle. *Time: 16 minutes.
Express This cycle will quickly wash lightly soiled dishes. *Time: 32 minutes. For faster drying, select Heated Dry or Power Dry.
(on some models) The final rinse temperature will be increased. Heated Dry or Power Dry will add 15 to 50 minutes to the cycle time.
When the Clean light comes on, open the door, pull the racks out, and the dishes will “flash” dry in approximately
five minutes.
eWash This cycle will efficiently wash dishes using about 2 gallons of water and .8 KWhr. Selecting Power Dry with this cycle
(on some models) adds an energy efficient 50 to 90 minute dry period. Drying is accomplished with an efficient 2 watt fan.
*Time: 1 hour 3 minutes.
*Washing time only. Does not include drying time, Auto Hot Start, or options. NOTE: If the incoming water temperature is too low,
the Auto Hot Start feature may add up to 11 minutes of additional time.
4
6
Getting started!
Select Options
The light by the selected button will be lit to indicate which Option has been selected.
5
Normal Temp
This option is for normally soiled dishes, optimizes wash performance while conserving energy.
Wash Temp
Boost or
Boost Temp
This option increases the temperature to help clean heavily soiled dishes and will increase the cycle time by
20 to 50 minutes. Option may be turned On or Off during the wash cycle. This option will also improve dry
performance on the Normal cycle.
Wash Temp
Sani or
Sanitize
Temp
This option raises the water temperature in the final rinse to sanitize your dishware but may increase cycle
time by 60 minutes. The cycle length will vary depending on the temperature of your inlet water.
NOTE
: This option is monitored for sanitization requirements. If the cycle is interrupted during or after the
main wash portion or if the incoming water temperature is so low that adequate water heating cannot be
achieved, the sanitizing conditions may not be met. In these cases, the Sanitized or Cycle Sanitized light will
not illuminate at the end of the cycle. Utilizing this option will modify the cycle to meet the requirements of
Section 6, NSF 184 for soil removal and sanitization efficacy.
NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.
Heated Dry or
Power Dry
Off
Shuts off the drying option. Dishes air dry naturally and energy is saved. Open the dishwasher door to speed
drying.
Heated Dry or
Power Dry
On
Turns on the option for faster drying. This option may add up to 85 minutes to the cycle time. On models
with the hidden heater feature, this option boosts the temperature of the dishwasher during the final rinse
portion of the cycle then utilizes a fan to circulate air to dry the dishes. This very efficient fan may run for an
additional 90 minutes after the cycle is complete to maximize drying performance. Fan operation will end if
the door is opened during this 90 minute period. This option is not available with the Rinse cycle.
Steam
(Prewash)
(on some models)
For use with heavily soiled and/or dried-on, baked-on soils. This option MUST be selected PRIOR to starting
the cycle. The Steam option adds up to 30 minutes to the cycle time. This option is available with Heavy,
AutoSense, and Normal cycles.
Pre Soak
(on some models)
Use this option to improve wash performance with heavy or dried-on soils. This option is available on Heavy,
AutoSense, and Normal cycles and may add up to 30 minutes to the cycle time.
Wash Zones
(on some models)
Selecting either the Upper or Lower Wash Zones will target dishwashing of just one rack. This will shorten the
cycle time and conserve energy. This option should be used when dishes are placed in only one rack.
Bottle Jets
(on some models)
This option increases the time that the bottle jets are on and may add up to 23 minutes to the cycle time.
Use this to wash difficult to clean, dishwasher safe baby bottles, sport bottles, tall coffee cups, etc. See use
recommendations in the Loading the dishwasher section.
Delay Hours
Delays the start of a wash cycle up to 8 to 12 hours depending on model. Press Delay Hours, to select the
number of hours, then press Start one time and close door to begin countdown. The cycle will start once
allotted time has expired.
Control Lock
You can lock the controls to prevent selections from being made. You can also lock the controls after you
have started a cycle to prevent cycle changes. For example, children cannot accidentally start the dishwasher
by pressing buttons with this option selected.
To LOCK the dishwasher control, depending on the model, press and hold the 1 or 2 buttons indicated on
the controls for 3 seconds. On some models, it will be the Heated Dry, another the Steam and Wash Temp
buttons, and another model is the Pre-Soak and Bottle Jets buttons. The Control Lock light will turn on to
indicate the control is locked.
To UNLOCK the dishwasher control, depending on the model, press and hold the 1 or 2 buttons indicated on
the controls for 3 seconds. The Control Lock light will turn off to indicate the control is unlocked.
GEAppliances.com
Cycle Indicator Lights and Sounds
7
7
Start Dishwasher
6
Start
Press the Start button and close the door within 4 seconds to start the cycle or begin the Delay Hours
countdown. The wash cycle will begin shortly after closing the door. The display will turn off if the door remains
open for two minutes. To activate the display, close and open the door or press any button.
Interrupt or
Pause
To interrupt or pause a dish cycle, slowly open the door. Opening the door will cause the wash cycle to pause.
The dishwasher will beep every minute to remind you to close the door. To restart or resume the cycle, press
Start, and close the door within 4 seconds.
Cancel
To cancel a wash cycle, press and hold the Start button for 3 seconds and close door. The dishwasher will
drain, emit a beep sound, and the wash cycle light will turn OFF.
Sanitized or
Cycle Sanitized
Displayed at end of the cycle when Wash Temp Sani or Sanitize Temp has been selected and dishwasher has
met requirements for sanitization. See Wash Temp Sani or Sanitize Temp, for complete description. Closing
door or pressing any button will turn off light.
Clean or Cycle
Complete
Displayed when a wash cycle is complete. The light stays ON as a reminder that the dishes are clean. The light
will turn off when the door is opened.
Low Rinse Aid
(on some models)
Displayed when rinse agent is low or empty. See page 8 for Use a Rinse Agent. To turn indicator off, press the
Pre-Soak or Steam button 7 times within 5 seconds. Repeat this process to turn the Low Rinse Aid indicator
back on.
Cycle Status
(on some models)
The indicator light on the door front will change color to indicate the wash status. During the wash cycle, the
indicator light will be amber. When the wash cycle is complete, the light will change to green.
Sounds
The dishwasher will emit a sound to indicate cycle completion, button presses, and door ajar. To mute all
sounds, press the Heated Dry or Power Dry button 7 times within 5 seconds. Repeat this process to turn
sounds back on.
Sabbath/
Door Wake
Up Mode
(on some models)
To turn this option ON/OFF, press and hold the START and WASH TEMP buttons for 5 seconds, close the door and
wait
3 minutes for the dishwasher to go into sleep mode. In the OFF mode, the control display, control sounds,
and interior lights
(on some models)
will not respond to the door opening/closing. This mode can be used when
observing certain religious holidays such as the Sabbath. To activate the control and interior lights
(on some
models)
, press any button.
Using the dishwasher.
Check the Water Temperature
The entering water should be at least 120°F (49°C) and not
more than 150°F (66°C) for effective cleaning and to prevent
dish damage. Check the water temperature with a candy or
meat thermometer.
Turn on the hot water faucet nearest the dishwasher,
place the thermometer in a glass and let the water run
continuously into the glass until the temperature stops rising.
8
Rinse agents, such as Cascade
®
Platinum Rinse Aid
are designed for great drying action and to protect
against spots and film build-up on your dishes, glasses, flatware, cookware, and plastic.
Filling the Dispenser
The rinse agent dispenser holds 3.5 oz. (104 ml) of rinse agent. Under normal
conditions, this will last approximately one month - depending on setting.
1
Make sure the dishwasher door is fully open.
2
Open the Rinse Agent dispenser door.
3
Slowly add rinse agent until the cup is full. You may need to pause several times to
allow rinse aid to settle.
4
Clean up any spilled rinse agent with a damp cloth to prevent foam from forming
inside the dishwasher.
5
Close the Rinse Agent dispenser door.
Rinse Aid Setting
The amount of rinse agent released into the final wash can be adjusted.
If water drops or hard water spots
remain on dishes after the dry cycle,
increase the setting.
To adjust the setting
Open the
Rinse Agent
dispenser door;
then turn the adjuster clockwise to
increase the amount of rinse agent,
counterclockwise to reduce the amount
of rinse agent.
Use a Rinse Agent
Rinse
agent
adjuster
Indicator
window
Clockwise to reduce
water drops and
hard water spots
Counterclockwise
to reduce foaming
Leak Protection (on some models)
If a leak is detected, the dishwasher will drain and the cycle
will stop. The display will show “LEAK DETECTED”. Call for
service.
GEAppliances.com
The detergent dispenser is located in the center of
the dishwasher door. It has two compartments. The
main wash compartment is found inside the detergent
dispenser. To open, press the button on the side of the
dispenser. The pre-wash compartment is on the lid of
the detergent dispenser. Use the pre-wash compartment
only when your water is extremely hard or when you
have a heavy soiled load. The pre-wash compartment
is not used when tablet or packet detergents are used.
NOTE: Do not load large items in the lower rack where
they may block the wash jets from rinsing out the
detergent dispenser.
You may use tablet, packet, powder, liquid or gel
automatic dishwasher detergent. Make sure you use
only detergents specifically labeled for use in automatic
dishwashers. Never use liquid hand dish detergent
in an automatic dishwasher. Sudsing and poor wash
performance will result with the use of improper
detergents.
Detergents should be stored in a dry location and in their
original container to prevent loss of effectiveness. Place
detergent in the cup just prior to starting the dishwasher
and then close the cover. The cover will open during the
wash cycle.
Filling the Detergent Dispenser
GE Appliances recommends using detergent in tablet or
packet form. Independent testing has shown this form of
detergent is very effective in the dishwasher. Cascade
®
Platinum ActionPacs
are an example of this type of
detergent. Simply put a tablet or packet into the main
wash compartment and slide to close the detergent cup
cover. Please notice that the tablet or packet must be
placed in the main wash compartment of the detergent
cup. If the tablet or packet is placed in the prewash
compartment or tossed in the bottom of the dishwasher,
the detergent will be flushed down the drain in a very
short period of time and will thus be wasted. Wash
performance will be very poor as a result.
If you choose to use detergent in powder, liquid or gel
form, the amount of detergent you use will be determined
by the hardness of your water, the temperature of your
water, and the food soil load inside the dishwasher.
Contact your water company to get information about
the hardness of the water in your area. Water hardness is
measured in grains per gallon. Use this information and
the table above to determine the amount of detergent
to use. You may purchase a hard water test strip from
GE Appliances. Call 1-877-959-8688 and ask for part
number WD01X10295. In Canada, call 1-800-661-1616.
Using too much detergent with very soft and/or very
hot water may cause a condition called etching on your
glassware. Etching is a permanent cloudiness in your
glassware. This condition is irreversible. However, using
too little detergent will cause poor wash performance.
Use the table as a starting point and then adjust the
amount of detergent you use. Use just enough to get
good wash performance. Using just the right amount of
detergent will provide great wash performance without
wasting detergent or etching glassware.
DO NOT USE HAND DISH DETERGENT
NOTE: Using a detergent that is not specifically designed
for dishwashers will cause the dishwasher to fill with
suds. During operation, these suds will spill out of the
dishwasher vents, covering the kitchen floor and making
the floor wet.
Because so many detergent containers look alike, store
the dishwasher detergent in a separate space from
all other cleaners. Show anyone who may use the
dishwasher the correct detergent and where it is stored.
While there will be no lasting damage to the dishwasher,
your dishes will not get clean using a dishwashing
detergent that is not formulated for automatic
dishwashers.
Detergent Dispenser
Number of
Grains/Gal.
Detergent Cups to Fill
Less than 4 Fill cup to 1/3 full
4 to 8 Fill cup to 2/3 full
8 to 12 Fill cup completely full
Greater than 12
Fill both main wash cup and pre
wash cup
Pre-Wash
Main
Wash
Rinse Agent
Detergent
Dispenser
Push/Slide
to Close
9
About Appliance Communication.
10
WiFi Connect
(on some models) (for customers in the United States)
Your dishwasher is GE Appliances WiFi Connect
capable. A WiFi communciation card is built into
the product allowing it to communicate with your
smartphone for remote monitoring, control and
notifications.
Please visit www.GEAppliances.com/connect
to connect your appliance, learn more about
connected appliance features and learn what
connected appliance app’s will work with your
smartphone.
WiFi Connectivity: For assistance with the appliance
or the ConnectPlus network connectivity, please call
GE Appliances at 800-GE-CARES.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2.
This device must accept any interference received, including interference that may cause undesired
operation. This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
Labelling: Changes or modifications to this unit not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.
Loading the dishwasher. GEAppliances.com
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware
baskets may vary from your model.
11
Sports bottle held in
place over a Bottle Jets
clip
Baby bottle held in place
under a Bottle Jets clip
The Bottle Jets system (on some models) is the
ideal location to position baby bottles, tall sports
bottles, or other tall items with narrow openings. The
Bottle Jets clips hold bottles with small openings
in place so water jets are directed inside the bottles
to clean hard to reach areas. Clips can be installed or
removed by simply slipping the clip opening over the
top of the nozzle.
Clip
Nozzle
Bottle Jets
Upper Rack
The upper rack is primarily for glasses, cups, and
saucers. For best wash performance, tilt cup and
glass openings toward the center of the rack. Other
items such as pots, pans, and plates may be placed
in the upper rack. This is also a secure place for
dishwasher-safe plastic items. The upper rack can
be used for odd sized utensils. Sauce pans, mixing
bowls, and other similarly shaped items should
be placed face down for best wash performance.
Ensure small plastic items are secure so that they
cannot fall on the heater at the bottom of the
dishwasher, potentially damaging the item. Some
models are equipped with a hidden heater, so
dishwasher safe plastic items can be placed in the
lower rack.
IMPORTANT: Ensure items in the upper rack do not
interfere with the 3rd Rack (on some models) when
loading and unloading.
IMPORTANT: Ensure that items do not protrude
through the bottom of the rack or silverware basket
where they will block the rotation of the middle spray
arm. This could result in noise during operation and/
or poor wash performance.
Loading the dishwasher (cont.).
To add flexibility in loading, the stem safe shelf
(on some models) may be placed in the up or
down position or unfolded and placed in the lower
unfolded position. The shelf may also be used to
secure stemware such as wine glasses. Because
these stemware items come in various sizes, slowly
push the rack in to ensure the items do not bump
into the edges of the dishwasher, which may cause
damage to the items.
The upper rack allows 2” of adjustment up or down
to accommodate large items. The upper rack may
be lowered by pushing the long flaps on each side of
the rack. This will allow you to lower the rack (see fig.
Upper Rack). To raise the rack, lift up on the rack until
the rack locks in place.
The fold down tines (on some models) provide
flexibility for extra-large and hard-to-fit items.
The tine rows can be adjusted to a vertical or
lay-down position.
Push
Upper Rack
Place the slots in the
utility shelf clips over
the vertical
rack wires
and
push down to
attach
utility shelf onto
second wire of rack
A loaded upper rack
may be heavier than
anticipated. To prevent minor injury or
damage to the contents, do not raise or
lower the upper rack after the rack is
loaded.
CAUTION
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware
baskets may vary from your model.
8 Place Settings - Upper Rack
Models - GDF570, GDF650, GDT655, PDF820, PDT825, PDT845
& CDT835
12
Models - DDT595, GDT695, PDT855 & CDT865
On some models, the upper rack may be adjusted to accommodate
larger items. To adjust the upper rack, fully extend the upper rack and
remove the two plastic end caps on the front of the rails. Remove the
upper rack. Select the set of rollers on the side of the rack that provides
the desired height, and reinstall the upper rack by guiding the rack
rails between the appropriate set of rollers. With the rack reinstalled,
replace the two plastic end caps, ensuring the snap is properly
engaged. Failure to properly engage the end caps may result in the
rack falling from the dishwasher.
End
Cap
Rollers
Rail
13
10 Place Settings - Upper Rack
Models - GDF570, GDF650, GDT655, PDF820, PDT825, PDT845,
& CDT835
12 Place Settings - Upper Rack
Models - GDF650, GDT655, PDF820, PDT825, PDT845 &
CDT835
Models - GDF570
GEAppliances.com
Models - PDT855 & CDT865
Models - DDT595 & GDT695
Models - DDT595, GDT695, PDT855 & CDT865
Lower Rack
The lower rack is best used for plates, saucers and cookware
items. Large items, such as broiler pans and baking racks should
be placed along the sides of the rack. If necessary, oversized
glasses and mugs can be placed in the lower rack to maximize
loading flexibility. Plates, saucers and similar items should be
placed between the tines in the direction that allows the item to
remain secure in the rack.
NOTE:
Do not load large items in the lower rack where they may
block the wash jets from rinsing out the detergent dispenser.
The lower
rack fold
down tines
(on some
models) can
be adjusted
to different
upright angles
or placed flat
to provide
flexibility for
hard-to-fit or
extra-large items.
The reversible tine blocks (on some models) are designed to
allow greater flexibility in loading dishes. The direction of the
tine blocks can be changed to match your preferred loading
direction as shown in Figure A or Figure B:
To adjust the tine block direction, remove the clips securing
the tine blocks to the racks by pulling up on the tab, then
gently flex the retaining wire from the center to unseat the
tine block from the lower rack. The tine block may be turned
in the opposite direction to reverse loading direction. Secure
the tine block to the rack using the same process and be
sure to snap the clips back in place.
To change the direction of the fold down tines, lower the
tines, then pull away from the bar clips that secure the
tines to the rack and remove. Reverse the direction of the
tines, orienting the handle on the opposite side of the rack.
Reattach the tines to the bar clips by pushing the tines back
until they click in place. The indexer will also need to be
switched to the opposite side of the dishwasher. To remove
the indexer, simply slide it the in the direction labeled
“unlock.” Then, align the indexer with the rack on the other
side and slide in the direction that says “lock” in order to
reattach the indexer to the rack.
IMPORTANT:
It is important to ensure that items do not
protrude through the bottom of the rack or the silverware
basket where they will block the rotation of the lower spray
arm. Also, ensure that large plates, pots, or tall items don’t
hit the mid spray arm. This could result in noise during
operation and/or poor wash performance.
Loading the dishwasher (cont.).
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware
baskets may vary from your model.
14
3 Angled
Positions
Available
or Folded
Down
Figure A Figure B
Clip
Indexer
To lock, slide right.
To unlock, slide left.
Bar Clip
The clips can be a choke hazard
for small children if removed from
the dishwasher. Keep out of reach of children.
WARNING
15
8 Place Settings - Lower Rack
Models - GDF570, GDF650, GDT655, PDF820, PDT825, PDT845
& CDT835
10 Place Settings - Lower Rack
Models - GDF570, GDF650, GDT655,
PDF820, PDT825, PDT845 & CDT835
12 Place Settings - Lower Rack
Models - GDF570, GDF650, GDT655, PDF820, PDT825, PDT845
& CDT835
Models - DDT595, GDT695, PDT855 & CDT865
Models - PDT855 & CDT865 Models - DDT595 & GDT695
Models - DDT595, GDT695, PDT855 & CDT865
GEAppliances.com
Loading the dishwasher (cont.).
For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware
baskets may vary from your model.
16
8 Place Settings
10 Place Settings 12 Place Settings
3rd Rack (on some models)
The 3rd rack is the recommended location for silverware and
large utensils
IMPORTANT NOTES:
Do not allow cutlery of different materials to touch each
other in the 3rd rack. Doing so may cause discoloration of
the cutlery.
The tray is only meant to be used with a GE Appliances
3rd rack dishwasher to hold silverware, cooking utensils,
and other small items. Using the tray for any other
purpose could result in damage to the tray or damage to
anything interacting with the tray.
Ensure that the 3rd rack is fully closed before shutting the
dishwasher door. Shutting the door with the rack partially
extended could cause damage to the dishwasher.
Take care when loading, unloading,
or transporting the silverware or
utensil tray. The tray may contain sharp or heavy
items. If items are dropped from the tray or the tray is
dropped, injury could occur.
CAUTION
The 3rd rack is also removable to allow extra large items to be placed in the upper rack:
To remove the 3rd rack:
1
With the rack fully extended, lift the front of the rack so that the
rack roller wheels clear the retaining hook
.
2
Continue to pull the rack until the remaining rack roller wheels
clear the retaining hook.
3
Replace the rack by aligning the rack roller wheels on the
retaining hook and rack rails – Ensure all roller wheels are
located on top of the rack rails
.
Silverware Basket
Place flatware in the removable silverware baskets. Sharp
objects, such as forks and knives, may be placed with the
handles facing up, in order to protect your hands. For the
best wash performance, place other items such as spoons
with the handles facing down. Avoid allowing items to
nest together, which may keep them from being properly
washed. When loading, distribute items evenly in the basket.
The silverware baskets may also be used for small items,
such as measuring spoons, baby bottle nipples, plastic lids,
or corn cob holders. The silverware basket covers can be
closed to contain small items.
Deep Clean Silverware Jets (on some models)
Deep Clean Silverware Jets target stubborn, stuck-on food
and help separate nested spoons and forks to keep your
silverware spotless no matter how you load the silverware.
For optimal silverware cleaning, the use of silverware basket
lids is always recommended. For models with the third rack,
the Deep Clean Silverware Jets can also be used to clean
mixing bowls and other cookware.
Do not remove Deep Clean Silverware Jet
spray assembly from the dishwasher rack.
17
GEAppliances.com
Silverware/flatware is loaded using the silverware basket lids. This ensures great wash performance of the
silverware. Loading in this manner prevents nesting and makes sure all items are washed uniformly.
Silverware Basket - 10 Place Settings
Models - GDF570, GDF650, GDT655,
GDT695, PDF820, PDT825, PDT845 &
CDT835
Silverware Basket - 8 Place Settings
Models - GDF570, GDF650, GDT655,
GDT695, PDF820, PDT825, PDT845 &
CDT835
Silverware Basket - 12 Place Settings
Models - GDF570, GDF650, GDT655,
GDT695, PDF820, PDT825, PDT845 &
CDT835
Silverware Basket
- 12 Place Settings
Models - DDT595, PDT855 & CDT865
NOTE: Refer to the 3rd Rack in this
Loading The Dishwasher section.
Silverware Basket
- 10 Place Settings
Models - DDT595, PDT855 & CDT865
Silverware Basket
- 8 Place Settings
Models - DDT595, PDT855 & CDT865
NOTE: Refer to the 3rd Rack in this
Loading The Dishwasher section.
Deep Clean
Silverware Jets
Ensure tabs on back
of silverware basket
are hooked on top
wire of lower rack
Silverware
basket lids
Care and cleaning.
Cleaning the Control Panel
To clean the control panel, use a lightly dampened cloth. Then
dry thoroughly.
Stainless Steel Inner Door and Tub
The stainless steel used to make the dishwasher tub and inner
door provides the highest reliability available in a GE Appliances
dishwasher.
If the dishwasher tub or inner door should be scratched or
dented during normal use, they will not rust or corrode. These
surface blemishes will not affect their function or durability.
Cleaning the Exterior Door Panel
Before cleaning the front panel, make sure you know what type
of panel you have. Refer to the last two letters of your model
number. You can locate your model number on the left-hand
tub wall just inside the door. If your model number ends with BB,
CC, WW, SA or ES then you have a painted door panel. If your
model number ends with SS, then you have a Stainless Steel
door panel. If your model number ends with II, then you have an
Integrated door panel.
Follow the instructions below for cleaning the door panel for
your specific model.
Painted Door Panel (model numbers ending in BB–black, CC–
bisque, WW–white, SA-silver or ES-slate)
Use a clean, soft, lightly dampened cloth, then dry thoroughly.
Stainless Steel Door Panel (model numbers ending in SS)
For cleaning rust and tarnish, cleaners with oxalic acid such
as Bar Keepers Friend Soft Cleanser™ will remove rust, tarnish
and small blemishes. Use only a liquid cleanser free of grit
and rub in the direction of the brush lines with a damp soft
sponge. Do not use appliance wax or polish on the stainless
steel.
For other blemishes and marks, use Stainless Steel Magic or a
similar product using a clean soft cloth. Do not use appliance
wax, polish,
bleach or products containing chlorine on
Stainless Steel. You can order Stainless Steel
Magic # WX10X29
through
GE Appliances Parts by calling 877.959.8688. In
Canada, call 1-800-661-1616.
Integrated Door Panel (model numbers ending in II)
This is a custom installed door panel, and you will need to refer
to the cabinet manufacturers recommendations for proper
cleaning.
* Lemi Shine® is a registered trademark of Envirocon Technologies, Inc.
18
Cleaning the Dishwasher Interior
To clean and de-odorize your dishwasher, use citric acid or
Lemi Shine®*, a detergent additive. Lemi Shine will break up
mineral deposits, and remove hard water film and stains. You
can order citric acid #WD35X151 through GE Appliances Parts
by calling 877-959-8688 or visiting GEApplianceparts.com. In
Canada, call 1-800-661-1616. You can purchase Lemi Shine
at your local grocery store or by calling GE Appliances at the
numbers above and ask for WX10X10019.
An air gap protects your dishwasher against water
backing up into it if a drain clogs. The air gap is not
a part of the dishwasher. It is not covered by your
warranty. Not all plumbing codes require air gaps,
so you may not have one.
The air gap is easy to clean.
1
Turn off the dishwasher and lift off the air gap
cover.
2
Remove the plastic cap under the cover and
clean with a toothpick.
3
Replace the cap and cover when the air gap is
clean.
Does Your Dishwasher Have an Air Gap?
If your dishwasher is left in an unheated place
during the winter, ask a service technician to:
1
Turn off electrical power to the dishwasher.
Remove fuses or trip circuit breaker.
2
Turn off the water supply and disconnect the
water inlet line from the water valve.
3
Drain water from the water inlet line and
water valve. (Use a pan to catch the water.)
4
Reconnect the water inlet line to the water
valve.
Protect Against Freezing
Check the air gap any
time your dishwasher
isn’t draining well.
Air gap
Inspect and clean the filters periodically. This should be done every other month or more depending on usage. If there is a
decrease in wash performance or dishes feel gritty, this is also an indication the filters need to be cleaned.
Cleaning the Filters
Ultra-Fine Filter
To clean the Ultra-Fine Filter, remove the bottom
rack. Twist the Ultra-Fine Filter counterclockwise
and lift to remove. Rinse filter with warm soapy
water and use a sponge to carefully remove
any stubborn particles. Scrubbing with scouring
pads or brushes can damage the filter. Once
cleaned, replace the Ultra-Fine Filter, and twist
it clockwise to lock in place.
Fine Filter
To clean the Fine Filter (mesh plate), remove the
bottom rack. Remove the Ultra-Fine Filter.
Twist each of the two retaining posts
located toward the back bottom of the tub
counterclockwise, and remove the Fine Filter.
Rinse filter with warm soapy water. Scouring
pads or brushes can scratch the filter surface
but a soft brush or sponge may be needed
to remove stubborn soils or calcium deposits
caused by hard water. Once cleaned, replace
the Fine Filter and the Ultra-Fine Filter. Twist the
two retaining posts clockwise to lock in place.
GEAppliances.com
19
Fine
Filter
Spray
Arm
Retaining
Posts
Ultra-Fine
Filter
The retaining posts
can be a choke hazard
for small children if removed from the
dishwasher. Keep out of reach of children.
WARNING
Before you call for service…
Troubleshooting Tips
Save time and money! Review the charts on the following pages, or visit GEAppliances.com.
In Canada visit www.GEAppliances.ca. You may not need to call for service.
Problem
Possible Causes What To Do
Start status The door was opened or the Press the Start button once and close the door within 4 seconds to start the
indicator light flashing cycle was interrupted.
dishwasher. Press the Start button a second time when the dishwasher is
running only if you wish to cancel the cycle.
Dishwasher BEEPS This is a reminder that yourPress Start and close the door.
once every minute dishwasher door has been left
open during operation. It will
continue beeping until you press
Start and close the door.
Display shows Possible leak is detected Some models are equipped with leak detection and the cycle will be cancelled if
“LEAK DETECTED” a leak is detected. The display will show “LEAK DETECTED”. Call for service.
Beeping at the end This is normal. The dishwasher To turn off the double beep indicator (or re-activate it if it was previously
of the cycle will beep twice at the end of the turned off), press the Heated Dry button 5 times within 3 seconds.
(on some models) cycle. A triple beep will sound to indicate the end-of-cycle beep option
has been turned on or off.
Dishes and flatware Ultra Fine or Fine filter is clogged • See the Care and cleaning section.
not clean
Low inlet water temperature Make sure inlet water temperature is correct (see the Using the dishwasher
section). Turn on the hot water faucet nearest the dishwasher, let run until
the water temperature stops rising. Then start the dishwasher and turn
off the faucet. This ensures the entering water is hot. Select Wash Temp Boost
or Boost Temp if available.
Water pressure is temporarily low Turn on a faucet. Is water coming out more slowly than usual? If so, wait until
pressure is normal before using your dishwasher. Normal water pressure to
the dishwasher should be 20-120 psi.
Air gap or disposer is clogged Clean the air gap or flush the disposer.
Improper rack loading Make sure large dishware does not block the detergent dispenser or the
wash arms. See the Loading the dishwasher section.
Poor performing detergent Use a highly rated detergent such as Cascade
®
Platinum ActionPacs
.
Spots and filming Extremely hard water Use rinse agents such as Cascade
®
Platinum Rinse Aid
to prevent spots and
on glasses and prevent new film buildup.
flatware
If water is extremely hard, a softener may be required.
Low inlet water temperature Make sure water temperature is at least 120°F (49°C).
Overloading or improper
Load dishwasher as shown in the Loading Place Settings section.
loading of the dishwasher
Old or damp powder detergent Make sure detergent is fresh. Use a highly rated detergent such as Cascade
®
Platinum ActionPacs
.
Rinse agent dispenser empty Refill with rinse agent such as Cascade
®
Platinum Rinse Aid
.
Too little or low performing Make sure you use the proper amount of highly rated detergent.
detergent
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Cafe GDF650SGJ0BB Le manuel du propriétaire

Catégorie
Lave-vaisselle
Taper
Le manuel du propriétaire