Briggs & Stratton 074007-0 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: 074007-0

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

Ce manuel convient également à

Manual No. 203718GS Revision - (07/18/2007)

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WISCONSIN, U.S.A.

Air Compressor

Operator’s Manual

2 BRIGGSandSTRATTON.COM

Briggs & Stratton Power Products Group, LLC

900 North Parkway

Jefferson, WI 53549

reproduced or transmitted in any form by any means without

the express written permission of Briggs & Stratton Power

Products Group, LLC.

Thank you for purchasing this quality-built Briggs & Stratton air compressor. We are pleased that you’ve placed your

confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual, your

Briggs & Stratton air compressor will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with air compressors and

how to avoid them. This air compressor has been manufactured to provide an adequate volume of compressed air for

operating a variety of light-duty air tools (hand grinders, nailers, ratchets, or staplers), spraying equipment, and inflators

requiring less than 4.0 CFM air flow for operation. It is important that you read and understand these instructions thoroughly

before attempting to start or operate this equipment. Save these instructions for future reference.

This air compressor requires final assembly before use. Refer to the Assembly section of this manual for instructions on

final assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your air compressor. Consult your Yellow Pages.

There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also

contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at BRIGGSandSTRATTON.COM.

Air Compressor

Model Number

Revision

Serial Number

Date Purchased

3
FrançaisEspañol
Table of Contents
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unpack Air Compressor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Add Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Features and Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Air Compressor Operating Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Break-In Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Starting Your Air Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Stopping Your Air Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Extension Cords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Compressor Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Overload Protection Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Inspect Safety Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Inspect Tank Drain Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Pump Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Inspect / Clean Air Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Inspect Safety Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Before You Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Common Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4 BRIGGSandSTRATTON.COM

Operator Safety

Equipment Description

Read this manual carefully and become familiar

with your air compressor. Know its applications, its

limitations and any hazards involved.

This manual contains operation and maintenance information

for a twin tank single-stage air compressor that produces

4.0 CFM at 40 PSI (2.8 bars) and 3.0 CFM at 90 PSI

(6.2 bars) using an 120 Volt A.C. electric motor. This high

quality system features a direct drive oil lube pump with cast

iron sleeve, an easy start valve, and an air outlet. This unit

also features a motor overload protection feature with

manual restart.

This air compressor has been manufactured to provide an

adequate volume of compressed air for operating a variety of

light-duty air tools (hand grinders, nailers, ratchets,

staplers), spraying equipment, and inflators requiring less

than 4.0 CFM air flow for operation. Operate this compressor

ONLY in an ambient temperature range from 32° to 95°F

(0° to 35°C). This compressor is designed for a maximum of

70% duty per hour at full load.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter or otherwise improve the product and

this document at any time without prior notice.

Safety Rules

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial and/or a safety

message to alert you to hazards. DANGER indicates a hazard

which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury. CAUTION indicates a hazard

which, if not avoided, might result in minor or moderate

injury. NOTICE indicates a situation that could result in

equipment damage. Follow safety messages to avoid or

reduce the risk of injury or death.

Hazard Symbols and Meanings

A - Explosion F - Hot Surface

B - Fire G - Air Injection

C - Electric Shock H - Auto-Start

D - Toxic Fumes J - Flying Objects

E - Compressed Air K - Read Manual

A B C

D E F

G H

J K

WARNING

Spraying flammable or combustible liquids can

cause fire or explosion.

Compressor produces sparks during operation,

which can ignite flammable or combustible

vapors.

• DO NOT spray flammable or combustible liquids while smoking,

near sparks, open flames, pilot lights, any ignition source, or in

confined areas.

• Spray in an open, well ventilated area at least 20 feet

(6.1 meters) away from compressor or other ignition source.

WARNING

Contact with compressor or its cord can cause

electric shock or burn.

Improper grounding can result in electrical

shock.

Contact with components under protective cover

can cause electric shock or burn.

• DO NOT use grounding adapters. Inspect cord before each use.

• DO NOT operate with protective covers / guards removed or

damaged.

• DO NOT operate in wet conditions. Store unit indoors.

• Disconnect from power source and drain pressure from tank

when not in use or before servicing.

• DO NOT modify the plug provided. If it does not fit the available

outlet, a qualified electrician should install a proper outlet.

• A qualified electrician MUST make repairs to the cord set or

plug.

WARNING

Failure to read and follow instructions in

Operator’s Manual can result in death, bodily

injury and / or property damage.

• Before using this product, read this Operator’s Manual and

follow all Safety Rules and Operating Instructions listed.

• Make this manual available to other users of this equipment.

WARNING

Hidden internal tank corrosion can cause violent

explosion leading to severe injury and / or

property damage.

Exceeding pressure rating of attachments or

inflatables can cause severe injury and / or

property damage.

Tampering with or removing ASME Safety Valve

can cause explosion leading to severe injury

and / or property damage.

• DRAIN TANK after every 4 hours of use or daily by opening

drain fitting(s) and tilting compressor to empty accumulated

water.

• DO NOT modify or repair tank in any way.

• DO NOT adjust pressure greater than maximum rating of

attachments or inflatables.

• DO NOT tamper with or remove ASME Safety Valve. Check

ASME Safety Valve by pulling ring before each use. ASME

Safety Valve has been set to maximum safe rating.

6 BRIGGSandSTRATTON.COM

WARNING

Operating air compressor and tubing are HOT

and can cause burns.

• DO NOT touch compressor or tubing.

• Allow compressor to cool before servicing.

NOTICE

Serious damage may result if the break-in instructions are

not closely followed.

• This procedure is required before the air compressor is put into

service and when the Check Valve or a complete compressor

pump has been replaced.

WARNING

Compressed air is not breathable and can cause

bodily injury.

Some paints or solvents may be harmful if

inhaled or ingested, causing severe nausea,

fainting or poisoning.

• DO NOT use compressed air for breathing.

• Always use NIOSH respirator approved for your application

when spraying.

• Read all instructions with respirator so you are certain it will

provide necessary protection against inhaling harmful vapors.

WARNING

Compressed air stream from hose or tank drain

can cause soft tissue damage to exposed skin

and can propel objects leading to severe injury

and / or property damage.

• DO NOT direct air stream at self or others.

• DO NOT attempt to repair air hose(s).

• Always wear ANSI Z87.1 approved safety glasses with side

shields.

WARNING

Compressor can start any time when plugged in.

• STAY CLEAR

• Disconnect from power source and drain pressure from tank

when not in use or before servicing.

NOTICE

Serious damage may result if operating the unit with

insufficient oil. Check oil level daily or with each use.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Assembly

Unpack Air Compressor

1. Remove everything from carton except air compressor.

2. Lift air compressor out of carton.

Items in the carton include:

• Air Compressor

• Bottle of Compressor Pump Oil

• Oil Dipstick

• Operator’s Manual

If any of the above parts are missing or damaged, call the

helpline at (800) 743-4115.

Also recommended for use:

• Safety glasses (ANSI Z87.1 approved safety glasses

with side shields)

• Air hose - 25 ft (7.6M), 3/8 inch diameter

• Quick connector fitting - Use type I/M quick connect

fittings that attach to 1/4 inch NPT thread

• Hearing protection (ANSI S3.19-1974) in noisy

environments

• Respirator (NIOSH-approved) in dusty environments

• Oil funnel

Your compressor is ready for use when:

Properly serviced with supplied oil

Connected to a suitable power source

Completed Break-In Procedure

Add Oil

1. Place compressor on a flat, level surface.

2. Remove and discard the shipping cap. Using an oil

funnel, slowly fill pump with oil to notch on dipstick.

3. Reinstall dipstick (A) into oil fill opening (B).

4. Carefully remove dipstick and verify that oil level is at

proper level (C).

5. If oil level is too low, slowly add recommended oil into

oil fill to proper level on dipstick. If oil is above

MAXIMUM oil level (D), drain excess oil, as described

in Pump Oil.

6. Reinstall oil dipstick.

NOTICE

Serious damage may result if operating the unit with

insufficient oil. Check oil level daily or with each use.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

Inset of

Dipstick

8 BRIGGSandSTRATTON.COM

Features and Controls

Read this Operator’s Manual and safety rules before operating your air compressor.

Compare the illustrations with your air compressor, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

A - Safety Valve — Valve protects against excessive tank

pressure by ‘popping out’ at its factory setting, thus

relieving pressure.

B - Air Filter — Protects air compressor by filtering dust

and debris out of intake air.

C - Check Valve — When unit is operating, check valve is

open, allowing air to enter tank. At “cut-out” pressure,

check valve closes, preventing air from flowing back into

pump. Valve is not serviceable by user.

D - Oil Dipstick — Remove to check and add compressor

pump oil.

E - Air Compressor Pump — Pump compresses air into

tank.

F - Drain Valves — Valves are located near bottom of each

air tank and is used to drain condensation.

G - Pressure Control — Controls air pressure delivered to

Quick Connect Fitting; can be secured with locking ring.

H - ON - OFF Switch — Pull to ON position to power air

compressor. Push to OFF position to remove power.

J - Pressure Switch — Automatically starts motor when tank

pressure drops below “cut-in” pressure and stops motor

when pressure rises to “cut-out” pressure.

K - Quick Connect Fitting — Connect air tools here.

L - Overload Protector — If motor is overloaded, protector

shuts motor off. See Overload Protection Reset.

M - Regulated Pressure Gauge — Indicates air pressure at

quick connect fitting.

N - Tank Pressure Gauge — Gauge indicates air pressure

within air tank.

Items Not Illustrated:

Data Tag: The data tag contains serial number, model

number, and revision number information.

Pressure Release Valve: Located on top of tank adjacent to

quick connect fitting, valve automatically releases air from

internal compressor components at “cut-out” pressure or

when unit is shut off. Valve is not serviceable by user.

NOTE: See Glossary for definitions.

Operation

Air Compressor Operating Location

Locate the air compressor in a clean, dry and well-ventilated

area for operation. The air compressor should be placed at

least 12 inches (30 cm) away from walls or other

obstructions that could interfere with airflow.

The air compressor pump and shroud are designed to allow

for proper cooling. The ventilation openings on the

compressor are necessary to maintain proper operating

temperature. DO NOT place rags or containers on or near

these openings. Keep the air filter clear of obstructions that

could reduce airflow to the air compressor.

Operate the air compressor with unit located on a flat

surface to ensure that it receives proper lubrication.

If you have any problems with operation of your air

compressor, call air compressor helpline at (800) 743-4115.

If calling for assistance, please have the model, revision, and

serial number from the data tag available.

Grounding Instructions

1. The cord set and plug supplied with this unit contains a

grounding pin. This plug MUST be used with a

grounded outlet.

2. Make sure power outlet being used has same

configuration as air compressor’s plug.

DO NOT use a ground adapter.

3. Inspect plug and cord before each use. DO NOT use

compressor if there are signs of damage.

IMPORTANT: If these grounding instructions are not completely

understood, or if in doubt that air compressor is correctly

grounded, have installation checked by a qualified electrician.

Break-In Procedure

Before first use of this equipment, the system must undergo

a break-in operation, as described in this section.

1. Make sure ON - OFF switch is in OFF position (A).

2. Plug power cord into an isolated 120 Volt A.C.

grounded outlet. See Grounding Instructions.

3. Open both drain valves (B) (rotate fully

counterclockwise) to prevent air pressure build-up in

air tank during break-in period.

NOTE: Always drain air tank over a washable surface or in a

suitable container to prevent damaging or staining surfaces.

4. Pull ON - OFF switch to ON position. Compressor will

start.

5. Run compressor for 15 minutes. Make sure drain valve

remains open.

6. After 15 minutes, close both drain valves (rotate fully

clockwise). Air tank will fill to “cut-out” pressure and

compressor will stop.

NOTE: If you hear leaking air, pull quick connect coupler

back until it clicks to reset coupler valve.

NOTE: Check oil level in compressor after break-in.

The compressor has completed the break-in procedure and

is ready for normal use.

NOTICE

Serious damage may result if the break-in instructions are

not closely followed.

• This procedure is required before the air compressor is put into

service and when the Check Valve or a complete compressor

pump has been replaced.

WARNING

Improper grounding can result in electrical

shock.

• DO NOT use grounding adapters.

• DO NOT modify the plug provided. If it does not fit the available

outlet, a qualified electrician should install a proper outlet.

• A qualified electrician MUST make repairs to the cord set or

plug.

10 BRIGGSandSTRATTON.COM

Starting Your Air Compressor

1. Make sure ON - OFF switch (A) is in OFF position.

2. Plug power cord into an isolated 120 Volt A.C.

grounded outlet. See Grounding Instructions.

3. Turn pressure control knob (B) counterclockwise until

knob turns without resistance.

4. Pull ON - OFF switch to ON position. Compressor will

start.

NOTE: If the motor fails to start, refer to Troubleshooting.

NOTE: If you hear air leaking, pull quick connect coupler

back until it clicks to reset coupler valve.

The air compressor is fully automatic and is controlled by

the pressure switch. The compressor will run until pressure

in the air tank reaches cut-out pressure. The compressor will

restart when pressure in the air tank falls below the cut-in

pressure. See Glossary for definitions.

NOTE: Always operate the air compressor in well-ventilated

areas free of gasoline or other flammable/combustible

vapors. If the compressor is being used to spray volatile

chemicals (such as paint), locate the compressor at least

20 feet (6.1 meters) away from the spray area.

Stopping Your Air Compressor

1. Push ON - OFF switch to OFF position. Compressor

motor will stop.

2. If finished using compressor, unplug compressor’s

power cord from outlet.

3. Pull safety valve ring to release most of tank’s

compressed air. Release valve ring.

4. Open both drain valves to fully drain air tanks.

NOTE: Always drain air tank over a washable surface or in a

suitable container to prevent damaging or staining surfaces.

NOTE: The compressor generates condensation water

(condensate) that accumulates in the air tanks. Drain the

condensate every 4 hours or daily.

5. Close both drain valves.

Extension Cords

NOTE: Avoid use of extension cords.

The air compressor should be located where it can be

directly plugged into a grounded outlet. DO NOT use an

extension cord unless absolutely necessary. Instead,

increase the working reach of the air hose by attaching two

or more air hoses together.

If the use of an extension cord cannot be avoided, use these

guidelines:

• Use only a 3-wire extension cord that has a 3-blade

grounding plug, and a 3-slot outlet that will accept the

plug from the air compressor.

• Make sure the cord is in good condition.

• When compressor is used outdoors, use only extension

cords marked “Intended for Outdoor Use”.

• Follow these length restrictions:

Distance Needed . . . . . . . . . . . . . . . .Recommended Gauge

Less than 25 ft. (7.5 M) . . . . . . . . . . . . . . . . . . . . . .12 AWG

25 to 50 ft. (7.5 to 15 M) . . . . . . . . . . . . . . . . . . . . .10 AWG

More than 50 ft. (15 M) . . . . . . . . . . . . .Not Recommended

Compressor Operation

You do not have to use the maximum operating pressure at

all times because the air tool being used often requires less

pressure. Here are general guidelines for setting pressure.

1. With air compressor connected to proper power and

turned ON, attach desired air tool or accessory to quick

connect fitting. Use recommended air hose and quick

connect fitting.

2. Activate air tool and turn pressure control knob

clockwise to increase outlet pressure.

3. Observe regulated pressure gauge and adjust pressure

to recommended setting of accessory tool.

NOTE: You must adjust outlet air pressure while tool is

operating or activated.

4. Use lock ring on pressure control to lock in selected

pressure setting by tightening it against pressure

control knob.

5. Always operate this unit on a level surface to avoid

lubrication problems.

Overload Protection Reset

This compressor is equipped with an overload protection

feature that protects the motor. If the circuit breaker trips,

wait 15 minutes for the motor to cool. Then push the RESET

button (A) located on the motor shroud.

Also see Troubleshooting for more information.

Observe these safety precautions when operating air

compressor:

WARNING

Exceeding pressure rating of attachments or

inflatables can cause severe injury and / or

property damage.

• DO NOT adjust pressure greater than maximum rating of

attachments or inflatables.

WARNING

Operating air compressor and tubing are HOT

and can cause burns.

• DO NOT touch compressor or tubing.

• Allow compressor to cool before servicing.

WARNING

Compressed air is not breathable and can cause

bodily injury.

Some paints or solvents may be harmful if

inhaled or ingested, causing severe nausea,

fainting or poisoning.

• DO NOT use compressed air for breathing.

• Always use NIOSH respirator approved for your application

when spraying.

• Read all instructions with respirator so you are certain it will

provide necessary protection against inhaling harmful vapors.

WARNING

Compressed air stream from hose or tank drain

can cause soft tissue damage to exposed skin

and can propel objects leading to severe injury

and / or property damage.

• DO NOT direct air stream at self or others.

• Always wear ANSI Z87.1 approved safety glasses with side

shields.

WARNING

Compressor can start any time when plugged in.

• STAY CLEAR

• Disconnect from power source and drain pressure from tank

when not in use or before servicing.

WARNING

Contact with compressor or its cord can cause

electric shock or burn.

Compressor must be grounded.

• DO NOT use grounding adapters. Inspect cord before each use.

• DO NOT operate with protective covers / guards removed or

damaged.

• DO NOT operate in wet conditions. Store unit indoors.

• Disconnect from power source and drain pressure from tank

when not in use or before servicing.

12 BRIGGSandSTRATTON.COM

General Recommendations

To ensure efficient operation and longer life of the air

compressor, prepare and follow a routine maintenance

schedule. The routine described in this section is intended for

an air compressor used under normal daily working conditions.

If necessary, modify the schedule to suit the conditions under

which you use your compressor. Modifications will depend

upon hours of operation and working environment. Operating

air compressors in extremely dirty or hostile environments will

require more frequent maintenance checks.

NOTE: See Features and Controls and Operation for control

locations.

Inspect Safety Valve

1. Pull ring (A) on safety valve and observe that safety

valve operates freely.

2. If valve is stuck or does not operate smoothly, it must

be replaced with same type of valve. Take unit to

authorized service facility for repair.

Inspect Tank Drain Valves

1. Push ON - OFF switch to OFF and unplug unit.

2. Disconnect air tool or accessory from unit.

3. Pull ring on safety valve to reduce air pressure. Release

safety valve ring.

4. Open both drain valves (turn fully counterclockwise)

and permit accumulated water to be discharged. Valves

should operate smoothly and have full range of

operation.

5. After water has drained, close drain valves fully

clockwise.

NOTE: If drain valves are plugged, pull safety valve ring to

fully drain air from tanks. Remove, clean and reinstall drain

valves using pipe thread sealant.

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs first. More frequent service is required when operating in adverse

conditions noted below.

* Change oil after first 100 hours of operation, then every 300 hours thereafter.

** Inspect anually, replace as necessary.

Maintenance Schedule - Fill in Dates as You Complete Regular Service

Maintenance Task

Service Intervals

Service Dates

Daily Weekly

Every 50 Hours

or Yearly

Every 100 Hours

or Yearly

Inspect safety valve

Inspect fittings/valves

Drain tanks

Inspect oil level

Clean unit

Inspect and clean air filter

Change pump oil

Inspect safety labels

X**

WARNING

Compressed air stream from hose or tank drain

can cause soft tissue damage to exposed skin

and can propel objects leading to severe injury

and / or property damage.

• DO NOT direct air stream at self or others.

• Always wear ANSI Z87.1 approved safety glasses with side

shields.

Pump Oil

Checking Oil Level

Use these steps to check oil level:

1. Push ON - OFF switch to OFF and unplug unit.

2. Place unit on a flat, level surface.

3. Remove oil dipstick (A) and wipe dipstick with clean

cloth.

4. Reinstall dipstick into oil fill opening.

5. Carefully remove dipstick and verify that oil level is at

proper level (B).

6. If oil level is too low, slowly add recommended oil into

oil fill (C) to proper level on dipstick. If oil is above

MAXIMUM oil level (D), drain excess oil, as described

in next section.

7. Reinstall oil dipstick.

Changing Oil

At recommended oil change interval, follow these steps:

1. Push ON - OFF switch to OFF and unplug unit.

2. Place unit on a flat, level surface.

3. Remove oil dipstick and wipe dipstick with clean cloth.

4. Position a suitable container under drain plug (E) to

collect drain oil.

5. Use an adjustable wrench to remove hex head drain

plug.

6. Fully drain oil into container. Install drain plug and

tighten using adjustable wrench. Dispose of used oil

properly.

7. Using oil funnel, slowly add recommended oil. Check

oil level frequently with dipstick to avoid overfilling

compressor pump.

8. When oil is at proper level, reinstall oil dipstick and

wipe up any spilled oil.

Cleaning Unit

Keep your air compressor clean and dry by placing it in a

location far away from sources of contamination. Make sure

the unit is kept in a well-ventilated area. Protect hoses,

connectors, quick connects, and accessories from damage.

To prolong compressor life, perform these steps weekly. If

the operating environment is particularly dirty, perform daily.

1. Push ON - OFF switch to OFF and unplug unit.

IMPORTANT: DO NOT use jets of water or flammable liquids

to clean unit.

2. Use a soft cloth and a small brush for cleaning

accumulated dirt and debris from the following

locations:

• Louvers on end of motor shroud (F) (on opposite

end from oil fill location)

• Cooling fins (G) on top of air compressor pump

• Cooling fins (G) on sides of air compressor pump,

especially between sides of pump and shroud

• Oil fill and adjacent area on air pump housing

• Oil drain on air pump housing

• Pressure control knob, gauges, quick connect

fitting, and safety valve

Inset of

Dipstick

WARNING

Operating air compressor and tubing are HOT

and can cause burns.

• DO NOT touch compressor or tubing.

• Allow compressor to cool before servicing.

WARNING

Operating air compressor and tubing are HOT

and can cause burns.

• DO NOT touch compressor or tubing.

• Allow compressor to cool before servicing.

14 BRIGGSandSTRATTON.COM

Inspect / Clean Air Filter

Use the following steps to check and clean the compressor’s

internal air filter.

1. With air tank fully pressurized (ON - OFF switch in ON

position and motor stopped), push ON - OFF switch to

OFF position. Disconnect power cord from outlet.

2. Use phillips screwdriver to remove screw (H) holding

air filter cover (J) on compressor housing (K). Remove

air filter cover.

3. Remove air filter media (L).

IMPORTANT: DO NOT operate compressor with air filter

media removed.

4. If dirty, use compressed air to dislodge dirt from air

filter media. Also, blow debris out of air filter cover and

compressor filter housing.

NOTE: DO NOT use liquid solvents to clean filter media.

5. Replace air filter media in compressor filter housing.

6. Position air filter cover over air filter media. Use phillips

screwdriver to secure cover with screw.

NOTE: Replace air filter media if it is extremely dirty.

Inspect Safety Labels

As often as desired or at least yearly, inspect all labels

applied to the air compressor. All safety labels should be

present and readable. If any safety label is missing or

illegible, obtain a replacement from an authorized service

center or call the air compressor helpline at (800) 743-4115.

Storage

Before you store your air compressor, make sure you

perform the following:

1. Review Maintenance and perform scheduled

maintenance as necessary.

2. Push ON - OFF switch to OFF and unplug unit.

3. Turn pressure control knob counterclockwise until knob

turns freely.

4. Remove air tool or accessory.

5. Pull ring on safety valve and drain air from air tank to

reduce air pressure. Release safety valve ring.

6. Drain remaining air and water from tank by opening

drain valve fully counterclockwise.

7. Rock unit forward and back to agitate water as it drains

to obtain a more thorough emptying action.

8. After water has been drained, close drain valve fully

clockwise.

9. Protect electrical cord and air hose from damage (such

as being stepped on or driven over).

10. Store air compressor in clean, dry, indoor location.

WARNING

Compressed air stream from hose or tank drain

can cause soft tissue damage to exposed skin

and can propel objects leading to severe injury

and / or property damage.

• DO NOT direct air stream at self or others.

• Always wear ANSI Z87.1 approved safety glasses with side

shields.

WARNING

Compressed air stream from hose or tank drain

can cause soft tissue damage to exposed skin

and can propel objects leading to severe injury

and / or property damage.

• DO NOT direct air stream at self or others.

• Always wear ANSI Z87.1 approved safety glasses with side

shields.

Troubleshooting

Before You Call

If you have any problems with the operation of your air

compressor, please call the air compressor helpline at

(800) 743-4115. If calling for assistance, please have the

model, revision, and serial number information printed on

the data tag available.

PROBLEM CAUSE CORRECTION

Excessive tank pressure - Safety

Valve pops off.

Pressure switch does not shut off motor

when compressor reaches “cut-out”

pressure or “cut-off” setting too high.

Move ON - OFF switch to OFF position.

Contact trained service technician.

Air losses

1. Quick connect fitting cracked or

loose.

2. Check valve seat dirty or damaged.

3. Defective pressure switch release

valve.

4. Defective air tank.

5. Leaking seal.

6. Damaged regulator.

1. Tighten quick connect fittings where air

can be heard escaping. Replace fittings.

2. Contact trained service technician.

3. Contact trained service technician.

4. Air tank must be replaced. DO NOT

REPAIR TANK.

5. Contact trained service technician.

6. Contact trained service technician.

Knocking noise

Safety valve dirty or defective. Operate safety valve manually by pulling on

ring. If valve still leaks, have it replaced at an

authorized service center.

16 BRIGGSandSTRATTON.COM

PROBLEM CAUSE CORRECTION

Compressor is not

supplying enough air to

operate accessories.

1. Prolonged excessive use of air.

2. Compressor is not large enough for air

requirement.

3. Hole in hose.

4. Check valve restricted or leaks air.

5. Restricted air intake filter.

1. Decrease amount of air used.

2. Check the accessory requirement. If it is higher

than the CFM or pressure supplied by your air

compressor, you need a larger capacity air

compressor.

3. Inspect and replace if required.

4. Contact trained service technician.

5. Clean or replace air intake filter.

Motor will not run.

1. Motor overload protector switch has

tripped.

2. Tank pressure exceeds pressure switch

“cut-in” pressure.

3. Loose electrical connections.

4. Possible defective motor or starting

capacitor.

5. Pressure release valve on pressure

switch has not unloaded head

pressure.

6. Fuse blown, circuit breaker tripped.

1. Let motor cool for 15 minutes. Press RESET to

reset overload protector switch.

2. Motor will start automatically when tank

pressure drops below “cut-in” pressure

setting.

3. Contact trained service technician.

4. Contact trained service technician.

5. Drain pressure by setting ON - OFF switch to

OFF. If the pressure release valve does not

open, contact trained service technician.

6A. Check fuse box for blown fuse and replace as

necessary. Reset circuit breaker. DO NOT use a

fuse or circuit breaker with higher rating than

that specified for that branch circuit.

B. Check for proper fuse. Use a time delay fuse.

C. Check for low voltage conditions and/or proper

extension cord.

D. Disconnect all other electrical loads from

circuit used by air compressor OR operate air

compressor on dedicated branch circuit.

Contact trained service technician.

Glossary

Becoming familiar with these terms will help you understand

and operate most air compressors:

Air Delivery – A combination of psi and CFM. The air

delivery required by a tool or accessory is stated as

“’number’ (S)CFM at ‘number’ psi”. For example “5.1 CFM at

90 psi”. The combination of these values dictates the

required air compressor capacity.

Air Tank Capacity – The volume of air stored in the tank and

available for immediate use.

Alternating Current (AC) - Voltage that increases to a

maximum positive value (+) and falls back to zero and then

continues to a maximum negative value (-) and back to zero.

This cycle is repeated 60 times each second for 60 hertz AC

power.

ASME Certified - Indicates that the pressure vessel (air tank)

and related components are manufactured, tested, and

inspected to the specifications set by the American Society

of Mechanical Engineers.

ASME Safety Valve - A protection device that automatically

releases tank air if the air contained within exceeds a preset

maximum rating.

Cast Iron Sleeve - A thin iron cylinder cast into the cylinder

head, producing a harder surface between the aluminum

cylinder walls and steel piston rings, thus extending the life

of the compressor.

CFM or SCFM (Standard Cubic Feet per Minute). SCFM is

the volume of air, in cubic feet, that the compressor can

pump in one minute at a specific working pressure. The term

CFM is used in this manual.

Circuit Breaker - A thermal switch that opens a circuit if too

much current is passing through it. The air compressor

motor is protected by this resettable device.

Cut-In Pressure – As air is taken from the air tank, the tank

air pressure drops. At a certain low level, the pressure switch

senses this low pressure and turns-on the compressor

motor, thus refilling the air tank. The level at which the motor

switches ON is called the cut-in pressure.

Cut-Out Pressure – While the compressor is running, air is

being produced and stored in the air tank. If no air is being

used, air pressure will build in the tank. The pressure switch

senses this high pressure and at a certain high level, it turns

the compressor motor off. The level at which the motor

switches OFF is called the cut-out pressure.

Duplex Receptacle - Two 120 volt AC receptacles that are

tied together. Similar to common household outlets.

GFCI - Ground fault current interrupter. A device that will

sense current flow in the milliamp range in a power circuit to

ground conductor and activate a relay to open both line

conductors.

Ground - A connection, either intentional or accidental,

between an electric circuit and the earth or some conducting

body serving in place of the earth.

Pressure Control – Often called a regulator, this device is

used to adjust the air compressor’s pressure output. The

pressure control is adjusted to supply the psi value required

by certain air tools, as monitored on the regulated pressure

gauge.

psi - pounds per square inch. The measure of air pressure

delivered by the air compressor system.

Single Stage - Single stage refers to an air compressor with

one or more cylinders that take air in each cylinder at the

down stroke and compresses the air into the air tank on the

up stroke.

Tank Pressure Gauge – A device used to indicate the air

pressure contained in the air tank, in psi.

Two Stage - A two-stage compressor always has a minimum

of two cylinders - a low pressure (LP) cylinder (largest) and

an high pressure (HP) cylinder (smallest). As the LP piston

goes downward, air is taken in at atmospheric pressure; on

the upward stroke the LP piston discharges the air through

an intercooler and into the HP cylinder on its downward

stroke. On the upward stroke of the HP piston the air is

discharged into the air tank. Two-stage compressors are

recommended when tool usage is continuous.

Vibration Isolators – When installed, are designed to

minimize vibrations produced by the air compressor.

18 BRIGGSandSTRATTON.COM

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC AIR COMPRESSOR OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the air compressor that is defective in material or

workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This

warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in

our dealer locator map at BRIGGSandSTRATTON.COM.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW. ANY AND ALL IMPLIED WARRANTIES ARE

EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some

states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and

you may also have other rights which vary from state to state or country to country.

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated above.

“Consumer use" means personal residential household use by a retail consumer. “Commercial use" means all other uses, including use for commercial,

income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be considered as commercial use for purposes of

this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE

RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING

DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty

repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if

equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the

warranty is void if the manufacturing date or the serial number on the air compressor has been removed or the equipment has been altered or modified.

During the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under

normal use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not cover

repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized installation or

alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as, in our judgment,

to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as air filters, adjustments, and so forth.

• Other Exclusions: This warranty excludes wear items such as seals and o-rings, etc.This warranty also excludes air compressors that have been run

without oil or subjected to freezing with water in the tank(s). This air compressor is warranted for non-continuous use and should not be subjected to

continuous operation. Accessory parts, such as hoses or air tools not supplied with the compressor are excluded from the product warranty. This

warranty excludes failures due to acts of God and other force majeure events beyond the manufacturers control.

198183E, Rev. D, 12/31/2006

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

Effective October 1, 2005 replaces all undated Warranties and all Warranties dated before October 1, 2005

2 years

90 days

Consumer Use

Commercial Use

WARRANTY PERIOD

20 BRIGGSandSTRATTON.COM

Briggs & Stratton Power Products Group, LLC

900 N. Parkway

Jefferson, Wisconsin, 53549 U.S.A.

(800) 743-4115

Product Specifications

AC Frequency:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Hz

Rated AC Voltage: . . . . . . . . . . . . . . . . . 120 Volts, single phase

Pump Type: . . . . . . . . . . . . . . . . . . . Oil Lubricated Direct Drive

Lubricant:. . . . . . . . . . . . . . . . SAE 5W50 or 85W140 Synthetic

Oil Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . 7.168 oz. (200ml)

Air Delivery:

At 40 psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0 CFM

At 90 psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 CFM

Cut-In Pressure Setting: . . . . . . . . . . . . . . . . . 90 psi (6.2 bars)

Cut/Out Pressure Setting:. . . . . . . . . . . . . . . 125 PSI (8.7 bars)

Tank capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Gallons (15 L)

Tank Style: . . . . . . . . . . . . . . . . . . . . . . . . . . Twin Stack Vertical

Recommended Air Hose Size: . . . . . . . . . . 3/8 inch ID (14mm)

Air Fittings: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 inch NPT

Quick Connect Fitting Type: . . . . . . . . . . . . . . . . . . . . . . . . . I/M

Operating Temperature Range: . . . . 32° to 95°F (0° to + 35°C)

Shipping Weight: . . . . . . . . . . . . . . . . . . . . . . . . 62 lbs. (28 Kg)

Common Service Parts

Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200697GS

Air Compressor

La page charge ...

Briggs & Stratton 074007-0 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: 074007-0

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Briggs & Stratton 074007-0 User manual
español: Briggs & Stratton 074007-0 Manual de usuario

Briggs & Stratton 074007-0 Manuel utilisateur

Ce manuel convient également à

Briggs & Stratton 074007-0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents