Briggs & Stratton 074007-0 Manuel utilisateur

Catégorie
Compresseurs d'air
Taper
Manuel utilisateur

Ce manuel convient également à

Manual No. 203718GS Revision - (07/18/2007)
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
JEFFERSON, WISCONSIN, U.S.A.
Air Compressor
Operator’s Manual
2 BRIGGSandSTRATTON.COM
Briggs & Stratton Power Products Group, LLC
900 North Parkway
Jefferson, WI 53549
Copyright © 2007 Briggs & Stratton Power Products Group,
LLC. All rights reserved. No part of this material may be
reproduced or transmitted in any form by any means without
the express written permission of Briggs & Stratton Power
Products Group, LLC.
Thank you for purchasing this quality-built Briggs & Stratton air compressor. We are pleased that you’ve placed your
confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual, your
Briggs & Stratton air compressor will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with air compressors and
how to avoid them. This air compressor has been manufactured to provide an adequate volume of compressed air for
operating a variety of light-duty air tools (hand grinders, nailers, ratchets, or staplers), spraying equipment, and inflators
requiring less than 4.0 CFM air flow for operation. It is important that you read and understand these instructions thoroughly
before attempting to start or operate this equipment. Save these instructions for future reference.
This air compressor requires final assembly before use. Refer to the Assembly section of this manual for instructions on
final assembly procedures. Follow the instructions completely.
Where to Find Us
You never have to look far to find Briggs & Stratton support and service for your air compressor. Consult your Yellow Pages.
There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also
contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at BRIGGSandSTRATTON.COM.
Air Compressor
Model Number
Revision
Serial Number
Date Purchased
3
FrançaisEspañol
Table of Contents
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unpack Air Compressor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Add Oil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Features and Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Air Compressor Operating Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Grounding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Break-In Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Starting Your Air Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Stopping Your Air Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Extension Cords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Compressor Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Overload Protection Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Inspect Safety Valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Inspect Tank Drain Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Pump Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Inspect / Clean Air Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Inspect Safety Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Before You Call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Common Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4 BRIGGSandSTRATTON.COM
Operator Safety
Equipment Description
Read this manual carefully and become familiar
with your air compressor. Know its applications, its
limitations and any hazards involved.
This manual contains operation and maintenance information
for a twin tank single-stage air compressor that produces
4.0 CFM at 40 PSI (2.8 bars) and 3.0 CFM at 90 PSI
(6.2 bars) using an 120 Volt A.C. electric motor. This high
quality system features a direct drive oil lube pump with cast
iron sleeve, an easy start valve, and an air outlet. This unit
also features a motor overload protection feature with
manual restart.
This air compressor has been manufactured to provide an
adequate volume of compressed air for operating a variety of
light-duty air tools (hand grinders, nailers, ratchets,
staplers), spraying equipment, and inflators requiring less
than 4.0 CFM air flow for operation. Operate this compressor
ONLY in an ambient temperature range from 32° to 95°F
(0° to 35°C). This compressor is designed for a maximum of
70% duty per hour at full load.
Every effort has been made to ensure that information in this
manual is accurate and current. However, we reserve the
right to change, alter or otherwise improve the product and
this document at any time without prior notice.
Safety Rules
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
The safety alert symbol ( ) is used with a signal word
(DANGER, CAUTION, WARNING), a pictorial and/or a safety
message to alert you to hazards. DANGER indicates a hazard
which, if not avoided, will result in death or serious injury.
WARNING indicates a hazard which, if not avoided, could
result in death or serious injury. CAUTION indicates a hazard
which, if not avoided, might result in minor or moderate
injury. NOTICE indicates a situation that could result in
equipment damage. Follow safety messages to avoid or
reduce the risk of injury or death.
Hazard Symbols and Meanings
A - Explosion F - Hot Surface
B - Fire G - Air Injection
C - Electric Shock H - Auto-Start
D - Toxic Fumes J - Flying Objects
E - Compressed Air K - Read Manual
A B C
D E F
G H
J K
5
WARNING
Spraying flammable or combustible liquids can
cause fire or explosion.
Compressor produces sparks during operation,
which can ignite flammable or combustible
vapors.
DO NOT spray flammable or combustible liquids while smoking,
near sparks, open flames, pilot lights, any ignition source, or in
confined areas.
Spray in an open, well ventilated area at least 20 feet
(6.1 meters) away from compressor or other ignition source.
WARNING
Contact with compressor or its cord can cause
electric shock or burn.
Improper grounding can result in electrical
shock.
Contact with components under protective cover
can cause electric shock or burn.
DO NOT use grounding adapters. Inspect cord before each use.
DO NOT operate with protective covers / guards removed or
damaged.
DO NOT operate in wet conditions. Store unit indoors.
Disconnect from power source and drain pressure from tank
when not in use or before servicing.
DO NOT modify the plug provided. If it does not fit the available
outlet, a qualified electrician should install a proper outlet.
A qualified electrician MUST make repairs to the cord set or
plug.
WARNING
Failure to read and follow instructions in
Operator’s Manual can result in death, bodily
injury and / or property damage.
Before using this product, read this Operator’s Manual and
follow all Safety Rules and Operating Instructions listed.
Make this manual available to other users of this equipment.
WARNING
Hidden internal tank corrosion can cause violent
explosion leading to severe injury and / or
property damage.
Exceeding pressure rating of attachments or
inflatables can cause severe injury and / or
property damage.
Tampering with or removing ASME Safety Valve
can cause explosion leading to severe injury
and / or property damage.
DRAIN TANK after every 4 hours of use or daily by opening
drain fitting(s) and tilting compressor to empty accumulated
water.
DO NOT modify or repair tank in any way.
DO NOT adjust pressure greater than maximum rating of
attachments or inflatables.
DO NOT tamper with or remove ASME Safety Valve. Check
ASME Safety Valve by pulling ring before each use. ASME
Safety Valve has been set to maximum safe rating.
6 BRIGGSandSTRATTON.COM
WARNING
Operating air compressor and tubing are HOT
and can cause burns.
DO NOT touch compressor or tubing.
Allow compressor to cool before servicing.
NOTICE
Serious damage may result if the break-in instructions are
not closely followed.
This procedure is required before the air compressor is put into
service and when the Check Valve or a complete compressor
pump has been replaced.
WARNING
Compressed air is not breathable and can cause
bodily injury.
Some paints or solvents may be harmful if
inhaled or ingested, causing severe nausea,
fainting or poisoning.
DO NOT use compressed air for breathing.
Always use NIOSH respirator approved for your application
when spraying.
Read all instructions with respirator so you are certain it will
provide necessary protection against inhaling harmful vapors.
WARNING
Compressed air stream from hose or tank drain
can cause soft tissue damage to exposed skin
and can propel objects leading to severe injury
and / or property damage.
DO NOT direct air stream at self or others.
DO NOT attempt to repair air hose(s).
Always wear ANSI Z87.1 approved safety glasses with side
shields.
WARNING
Compressor can start any time when plugged in.
STAY CLEAR
Disconnect from power source and drain pressure from tank
when not in use or before servicing.
NOTICE
Serious damage may result if operating the unit with
insufficient oil. Check oil level daily or with each use.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
7
Assembly
Unpack Air Compressor
1. Remove everything from carton except air compressor.
2. Lift air compressor out of carton.
Items in the carton include:
Air Compressor
Bottle of Compressor Pump Oil
Oil Dipstick
Operator’s Manual
If any of the above parts are missing or damaged, call the
helpline at (800) 743-4115.
Also recommended for use:
Safety glasses (ANSI Z87.1 approved safety glasses
with side shields)
Air hose - 25 ft (7.6M), 3/8 inch diameter
Quick connector fitting - Use type I/M quick connect
fittings that attach to 1/4 inch NPT thread
Hearing protection (ANSI S3.19-1974) in noisy
environments
Respirator (NIOSH-approved) in dusty environments
Oil funnel
Your compressor is ready for use when:
Properly serviced with supplied oil
Connected to a suitable power source
Completed Break-In Procedure
Add Oil
1. Place compressor on a flat, level surface.
2. Remove and discard the shipping cap. Using an oil
funnel, slowly fill pump with oil to notch on dipstick.
3. Reinstall dipstick (A) into oil fill opening (B).
4. Carefully remove dipstick and verify that oil level is at
proper level (C).
5. If oil level is too low, slowly add recommended oil into
oil fill to proper level on dipstick. If oil is above
MAXIMUM oil level (D), drain excess oil, as described
in Pump Oil.
6. Reinstall oil dipstick.
NOTICE
Serious damage may result if operating the unit with
insufficient oil. Check oil level daily or with each use.
Damage to equipment resulting from failure to follow this
instruction will void warranty.
Inset of
Dipstick
B
D
C
A
8 BRIGGSandSTRATTON.COM
Features and Controls
Read this Operator’s Manual and safety rules before operating your air compressor.
Compare the illustrations with your air compressor, to familiarize yourself with the locations of various controls and
adjustments. Save this manual for future reference.
A - Safety Valve — Valve protects against excessive tank
pressure by ‘popping out’ at its factory setting, thus
relieving pressure.
B - Air Filter — Protects air compressor by filtering dust
and debris out of intake air.
C - Check Valve — When unit is operating, check valve is
open, allowing air to enter tank. At “cut-out” pressure,
check valve closes, preventing air from flowing back into
pump. Valve is not serviceable by user.
D - Oil Dipstick — Remove to check and add compressor
pump oil.
E - Air Compressor Pump — Pump compresses air into
tank.
F - Drain Valves — Valves are located near bottom of each
air tank and is used to drain condensation.
G - Pressure Control — Controls air pressure delivered to
Quick Connect Fitting; can be secured with locking ring.
H - ON - OFF Switch — Pull to ON position to power air
compressor. Push to OFF position to remove power.
J - Pressure Switch — Automatically starts motor when tank
pressure drops below “cut-in” pressure and stops motor
when pressure rises to “cut-out” pressure.
K - Quick Connect Fitting — Connect air tools here.
L - Overload Protector — If motor is overloaded, protector
shuts motor off. See Overload Protection Reset.
M - Regulated Pressure Gauge — Indicates air pressure at
quick connect fitting.
N - Tank Pressure Gauge — Gauge indicates air pressure
within air tank.
Items Not Illustrated:
Data Tag: The data tag contains serial number, model
number, and revision number information.
Pressure Release Valve: Located on top of tank adjacent to
quick connect fitting, valve automatically releases air from
internal compressor components at “cut-out” pressure or
when unit is shut off. Valve is not serviceable by user.
NOTE: See Glossary for definitions.
A
K
H
B
N
E
M
C
J
G
F
L
D
9
Operation
Air Compressor Operating Location
Locate the air compressor in a clean, dry and well-ventilated
area for operation. The air compressor should be placed at
least 12 inches (30 cm) away from walls or other
obstructions that could interfere with airflow.
The air compressor pump and shroud are designed to allow
for proper cooling. The ventilation openings on the
compressor are necessary to maintain proper operating
temperature. DO NOT place rags or containers on or near
these openings. Keep the air filter clear of obstructions that
could reduce airflow to the air compressor.
Operate the air compressor with unit located on a flat
surface to ensure that it receives proper lubrication.
If you have any problems with operation of your air
compressor, call air compressor helpline at (800) 743-4115.
If calling for assistance, please have the model, revision, and
serial number from the data tag available.
Grounding Instructions
1. The cord set and plug supplied with this unit contains a
grounding pin. This plug MUST be used with a
grounded outlet.
2. Make sure power outlet being used has same
configuration as air compressor’s plug.
DO NOT use a ground adapter.
3. Inspect plug and cord before each use. DO NOT use
compressor if there are signs of damage.
IMPORTANT: If these grounding instructions are not completely
understood, or if in doubt that air compressor is correctly
grounded, have installation checked by a qualified electrician.
Break-In Procedure
Before first use of this equipment, the system must undergo
a break-in operation, as described in this section.
1. Make sure ON - OFF switch is in OFF position (A).
2. Plug power cord into an isolated 120 Volt A.C.
grounded outlet. See Grounding Instructions.
3. Open both drain valves (B) (rotate fully
counterclockwise) to prevent air pressure build-up in
air tank during break-in period.
NOTE: Always drain air tank over a washable surface or in a
suitable container to prevent damaging or staining surfaces.
4. Pull ON - OFF switch to ON position. Compressor will
start.
5. Run compressor for 15 minutes. Make sure drain valve
remains open.
6. After 15 minutes, close both drain valves (rotate fully
clockwise). Air tank will fill to “cut-out” pressure and
compressor will stop.
NOTE: If you hear leaking air, pull quick connect coupler
back until it clicks to reset coupler valve.
NOTE: Check oil level in compressor after break-in.
The compressor has completed the break-in procedure and
is ready for normal use.
NOTICE
Serious damage may result if the break-in instructions are
not closely followed.
This procedure is required before the air compressor is put into
service and when the Check Valve or a complete compressor
pump has been replaced.
B
A
WARNING
Improper grounding can result in electrical
shock.
DO NOT use grounding adapters.
DO NOT modify the plug provided. If it does not fit the available
outlet, a qualified electrician should install a proper outlet.
A qualified electrician MUST make repairs to the cord set or
plug.
OR
10 BRIGGSandSTRATTON.COM
Starting Your Air Compressor
1. Make sure ON - OFF switch (A) is in OFF position.
2. Plug power cord into an isolated 120 Volt A.C.
grounded outlet. See Grounding Instructions.
3. Turn pressure control knob (B) counterclockwise until
knob turns without resistance.
4. Pull ON - OFF switch to ON position. Compressor will
start.
NOTE: If the motor fails to start, refer to Troubleshooting.
NOTE: If you hear air leaking, pull quick connect coupler
back until it clicks to reset coupler valve.
The air compressor is fully automatic and is controlled by
the pressure switch. The compressor will run until pressure
in the air tank reaches cut-out pressure. The compressor will
restart when pressure in the air tank falls below the cut-in
pressure. See Glossary for definitions.
NOTE: Always operate the air compressor in well-ventilated
areas free of gasoline or other flammable/combustible
vapors. If the compressor is being used to spray volatile
chemicals (such as paint), locate the compressor at least
20 feet (6.1 meters) away from the spray area.
Stopping Your Air Compressor
1. Push ON - OFF switch to OFF position. Compressor
motor will stop.
2. If finished using compressor, unplug compressor’s
power cord from outlet.
3. Pull safety valve ring to release most of tank’s
compressed air. Release valve ring.
4. Open both drain valves to fully drain air tanks.
NOTE: Always drain air tank over a washable surface or in a
suitable container to prevent damaging or staining surfaces.
NOTE: The compressor generates condensation water
(condensate) that accumulates in the air tanks. Drain the
condensate every 4 hours or daily.
5. Close both drain valves.
Extension Cords
NOTE: Avoid use of extension cords.
The air compressor should be located where it can be
directly plugged into a grounded outlet. DO NOT use an
extension cord unless absolutely necessary. Instead,
increase the working reach of the air hose by attaching two
or more air hoses together.
If the use of an extension cord cannot be avoided, use these
guidelines:
Use only a 3-wire extension cord that has a 3-blade
grounding plug, and a 3-slot outlet that will accept the
plug from the air compressor.
Make sure the cord is in good condition.
When compressor is used outdoors, use only extension
cords marked “Intended for Outdoor Use”.
Follow these length restrictions:
Distance Needed . . . . . . . . . . . . . . . .Recommended Gauge
Less than 25 ft. (7.5 M) . . . . . . . . . . . . . . . . . . . . . .12 AWG
25 to 50 ft. (7.5 to 15 M) . . . . . . . . . . . . . . . . . . . . .10 AWG
More than 50 ft. (15 M) . . . . . . . . . . . . .Not Recommended
A
B
11
Compressor Operation
You do not have to use the maximum operating pressure at
all times because the air tool being used often requires less
pressure. Here are general guidelines for setting pressure.
1. With air compressor connected to proper power and
turned ON, attach desired air tool or accessory to quick
connect fitting. Use recommended air hose and quick
connect fitting.
2. Activate air tool and turn pressure control knob
clockwise to increase outlet pressure.
3. Observe regulated pressure gauge and adjust pressure
to recommended setting of accessory tool.
NOTE: You must adjust outlet air pressure while tool is
operating or activated.
4. Use lock ring on pressure control to lock in selected
pressure setting by tightening it against pressure
control knob.
5. Always operate this unit on a level surface to avoid
lubrication problems.
Overload Protection Reset
This compressor is equipped with an overload protection
feature that protects the motor. If the circuit breaker trips,
wait 15 minutes for the motor to cool. Then push the RESET
button (A) located on the motor shroud.
Also see Troubleshooting for more information.
Observe these safety precautions when operating air
compressor:
WARNING
Exceeding pressure rating of attachments or
inflatables can cause severe injury and / or
property damage.
DO NOT adjust pressure greater than maximum rating of
attachments or inflatables.
A
WARNING
Operating air compressor and tubing are HOT
and can cause burns.
DO NOT touch compressor or tubing.
Allow compressor to cool before servicing.
WARNING
Compressed air is not breathable and can cause
bodily injury.
Some paints or solvents may be harmful if
inhaled or ingested, causing severe nausea,
fainting or poisoning.
DO NOT use compressed air for breathing.
Always use NIOSH respirator approved for your application
when spraying.
Read all instructions with respirator so you are certain it will
provide necessary protection against inhaling harmful vapors.
WARNING
Compressed air stream from hose or tank drain
can cause soft tissue damage to exposed skin
and can propel objects leading to severe injury
and / or property damage.
DO NOT direct air stream at self or others.
Always wear ANSI Z87.1 approved safety glasses with side
shields.
WARNING
Compressor can start any time when plugged in.
STAY CLEAR
Disconnect from power source and drain pressure from tank
when not in use or before servicing.
WARNING
Contact with compressor or its cord can cause
electric shock or burn.
Compressor must be grounded.
DO NOT use grounding adapters. Inspect cord before each use.
DO NOT operate with protective covers / guards removed or
damaged.
DO NOT operate in wet conditions. Store unit indoors.
Disconnect from power source and drain pressure from tank
when not in use or before servicing.
12 BRIGGSandSTRATTON.COM
General Recommendations
To ensure efficient operation and longer life of the air
compressor, prepare and follow a routine maintenance
schedule. The routine described in this section is intended for
an air compressor used under normal daily working conditions.
If necessary, modify the schedule to suit the conditions under
which you use your compressor. Modifications will depend
upon hours of operation and working environment. Operating
air compressors in extremely dirty or hostile environments will
require more frequent maintenance checks.
NOTE: See Features and Controls and Operation for control
locations.
Inspect Safety Valve
1. Pull ring (A) on safety valve and observe that safety
valve operates freely.
2. If valve is stuck or does not operate smoothly, it must
be replaced with same type of valve. Take unit to
authorized service facility for repair.
Inspect Tank Drain Valves
1. Push ON - OFF switch to OFF and unplug unit.
2. Disconnect air tool or accessory from unit.
3. Pull ring on safety valve to reduce air pressure. Release
safety valve ring.
4. Open both drain valves (turn fully counterclockwise)
and permit accumulated water to be discharged. Valves
should operate smoothly and have full range of
operation.
5. After water has drained, close drain valves fully
clockwise.
NOTE: If drain valves are plugged, pull safety valve ring to
fully drain air from tanks. Remove, clean and reinstall drain
valves using pipe thread sealant.
Maintenance
Maintenance Schedule
Follow the hourly or calendar intervals, whichever occurs first. More frequent service is required when operating in adverse
conditions noted below.
* Change oil after first 100 hours of operation, then every 300 hours thereafter.
** Inspect anually, replace as necessary.
Maintenance Schedule - Fill in Dates as You Complete Regular Service
Maintenance Task
Service Intervals
Service Dates
Daily Weekly
Every 50 Hours
or Yearly
Every 100 Hours
or Yearly
Inspect safety valve
X
Inspect fittings/valves
X
Drain tanks
X
Inspect oil level
X
Clean unit
X
Inspect and clean air filter
X
Change pump oil
X*
Inspect safety labels
X**
A
WARNING
Compressed air stream from hose or tank drain
can cause soft tissue damage to exposed skin
and can propel objects leading to severe injury
and / or property damage.
DO NOT direct air stream at self or others.
Always wear ANSI Z87.1 approved safety glasses with side
shields.
13
Pump Oil
Checking Oil Level
Use these steps to check oil level:
1. Push ON - OFF switch to OFF and unplug unit.
2. Place unit on a flat, level surface.
3. Remove oil dipstick (A) and wipe dipstick with clean
cloth.
4. Reinstall dipstick into oil fill opening.
5. Carefully remove dipstick and verify that oil level is at
proper level (B).
6. If oil level is too low, slowly add recommended oil into
oil fill (C) to proper level on dipstick. If oil is above
MAXIMUM oil level (D), drain excess oil, as described
in next section.
7. Reinstall oil dipstick.
Changing Oil
At recommended oil change interval, follow these steps:
1. Push ON - OFF switch to OFF and unplug unit.
2. Place unit on a flat, level surface.
3. Remove oil dipstick and wipe dipstick with clean cloth.
4. Position a suitable container under drain plug (E) to
collect drain oil.
5. Use an adjustable wrench to remove hex head drain
plug.
6. Fully drain oil into container. Install drain plug and
tighten using adjustable wrench. Dispose of used oil
properly.
7. Using oil funnel, slowly add recommended oil. Check
oil level frequently with dipstick to avoid overfilling
compressor pump.
8. When oil is at proper level, reinstall oil dipstick and
wipe up any spilled oil.
Cleaning Unit
Keep your air compressor clean and dry by placing it in a
location far away from sources of contamination. Make sure
the unit is kept in a well-ventilated area. Protect hoses,
connectors, quick connects, and accessories from damage.
To prolong compressor life, perform these steps weekly. If
the operating environment is particularly dirty, perform daily.
1. Push ON - OFF switch to OFF and unplug unit.
IMPORTANT: DO NOT use jets of water or flammable liquids
to clean unit.
2. Use a soft cloth and a small brush for cleaning
accumulated dirt and debris from the following
locations:
Louvers on end of motor shroud (F) (on opposite
end from oil fill location)
Cooling fins (G) on top of air compressor pump
Cooling fins (G) on sides of air compressor pump,
especially between sides of pump and shroud
Oil fill and adjacent area on air pump housing
Oil drain on air pump housing
Pressure control knob, gauges, quick connect
fitting, and safety valve
Inset of
Dipstick
C
E
D
B
A
WARNING
Operating air compressor and tubing are HOT
and can cause burns.
DO NOT touch compressor or tubing.
Allow compressor to cool before servicing.
WARNING
Operating air compressor and tubing are HOT
and can cause burns.
DO NOT touch compressor or tubing.
Allow compressor to cool before servicing.
F
G
14 BRIGGSandSTRATTON.COM
Inspect / Clean Air Filter
Use the following steps to check and clean the compressor’s
internal air filter.
1. With air tank fully pressurized (ON - OFF switch in ON
position and motor stopped), push ON - OFF switch to
OFF position. Disconnect power cord from outlet.
2. Use phillips screwdriver to remove screw (H) holding
air filter cover (J) on compressor housing (K). Remove
air filter cover.
3. Remove air filter media (L).
IMPORTANT: DO NOT operate compressor with air filter
media removed.
4. If dirty, use compressed air to dislodge dirt from air
filter media. Also, blow debris out of air filter cover and
compressor filter housing.
NOTE: DO NOT use liquid solvents to clean filter media.
5. Replace air filter media in compressor filter housing.
6. Position air filter cover over air filter media. Use phillips
screwdriver to secure cover with screw.
NOTE: Replace air filter media if it is extremely dirty.
Inspect Safety Labels
As often as desired or at least yearly, inspect all labels
applied to the air compressor. All safety labels should be
present and readable. If any safety label is missing or
illegible, obtain a replacement from an authorized service
center or call the air compressor helpline at (800) 743-4115.
Storage
Before you store your air compressor, make sure you
perform the following:
1. Review Maintenance and perform scheduled
maintenance as necessary.
2. Push ON - OFF switch to OFF and unplug unit.
3. Turn pressure control knob counterclockwise until knob
turns freely.
4. Remove air tool or accessory.
5. Pull ring on safety valve and drain air from air tank to
reduce air pressure. Release safety valve ring.
6. Drain remaining air and water from tank by opening
drain valve fully counterclockwise.
7. Rock unit forward and back to agitate water as it drains
to obtain a more thorough emptying action.
8. After water has been drained, close drain valve fully
clockwise.
9. Protect electrical cord and air hose from damage (such
as being stepped on or driven over).
10. Store air compressor in clean, dry, indoor location.
H
J
L
K
WARNING
Compressed air stream from hose or tank drain
can cause soft tissue damage to exposed skin
and can propel objects leading to severe injury
and / or property damage.
DO NOT direct air stream at self or others.
Always wear ANSI Z87.1 approved safety glasses with side
shields.
WARNING
Compressed air stream from hose or tank drain
can cause soft tissue damage to exposed skin
and can propel objects leading to severe injury
and / or property damage.
DO NOT direct air stream at self or others.
Always wear ANSI Z87.1 approved safety glasses with side
shields.
15
Troubleshooting
Before You Call
If you have any problems with the operation of your air
compressor, please call the air compressor helpline at
(800) 743-4115. If calling for assistance, please have the
model, revision, and serial number information printed on
the data tag available.
PROBLEM CAUSE CORRECTION
Excessive tank pressure - Safety
Valve pops off.
Pressure switch does not shut off motor
when compressor reaches “cut-out”
pressure or “cut-off” setting too high.
Move ON - OFF switch to OFF position.
Contact trained service technician.
Air losses
1. Quick connect fitting cracked or
loose.
2. Check valve seat dirty or damaged.
3. Defective pressure switch release
valve.
4. Defective air tank.
5. Leaking seal.
6. Damaged regulator.
1. Tighten quick connect fittings where air
can be heard escaping. Replace fittings.
2. Contact trained service technician.
3. Contact trained service technician.
4. Air tank must be replaced. DO NOT
REPAIR TANK.
5. Contact trained service technician.
6. Contact trained service technician.
Knocking noise
Safety valve dirty or defective. Operate safety valve manually by pulling on
ring. If valve still leaks, have it replaced at an
authorized service center.
16 BRIGGSandSTRATTON.COM
PROBLEM CAUSE CORRECTION
Compressor is not
supplying enough air to
operate accessories.
1. Prolonged excessive use of air.
2. Compressor is not large enough for air
requirement.
3. Hole in hose.
4. Check valve restricted or leaks air.
5. Restricted air intake filter.
1. Decrease amount of air used.
2. Check the accessory requirement. If it is higher
than the CFM or pressure supplied by your air
compressor, you need a larger capacity air
compressor.
3. Inspect and replace if required.
4. Contact trained service technician.
5. Clean or replace air intake filter.
Motor will not run.
1. Motor overload protector switch has
tripped.
2. Tank pressure exceeds pressure switch
“cut-in” pressure.
3. Loose electrical connections.
4. Possible defective motor or starting
capacitor.
5. Pressure release valve on pressure
switch has not unloaded head
pressure.
6. Fuse blown, circuit breaker tripped.
1. Let motor cool for 15 minutes. Press RESET to
reset overload protector switch.
2. Motor will start automatically when tank
pressure drops below “cut-in” pressure
setting.
3. Contact trained service technician.
4. Contact trained service technician.
5. Drain pressure by setting ON - OFF switch to
OFF. If the pressure release valve does not
open, contact trained service technician.
6A. Check fuse box for blown fuse and replace as
necessary. Reset circuit breaker. DO NOT use a
fuse or circuit breaker with higher rating than
that specified for that branch circuit.
B. Check for proper fuse. Use a time delay fuse.
C. Check for low voltage conditions and/or proper
extension cord.
D. Disconnect all other electrical loads from
circuit used by air compressor OR operate air
compressor on dedicated branch circuit.
Contact trained service technician.
17
Glossary
Becoming familiar with these terms will help you understand
and operate most air compressors:
Air Delivery – A combination of psi and CFM. The air
delivery required by a tool or accessory is stated as
“’number’ (S)CFM at ‘number’ psi”. For example “5.1 CFM at
90 psi”. The combination of these values dictates the
required air compressor capacity.
Air Tank Capacity – The volume of air stored in the tank and
available for immediate use.
Alternating Current (AC) - Voltage that increases to a
maximum positive value (+) and falls back to zero and then
continues to a maximum negative value (-) and back to zero.
This cycle is repeated 60 times each second for 60 hertz AC
power.
ASME Certified - Indicates that the pressure vessel (air tank)
and related components are manufactured, tested, and
inspected to the specifications set by the American Society
of Mechanical Engineers.
ASME Safety Valve - A protection device that automatically
releases tank air if the air contained within exceeds a preset
maximum rating.
Cast Iron Sleeve - A thin iron cylinder cast into the cylinder
head, producing a harder surface between the aluminum
cylinder walls and steel piston rings, thus extending the life
of the compressor.
CFM or SCFM (Standard Cubic Feet per Minute). SCFM is
the volume of air, in cubic feet, that the compressor can
pump in one minute at a specific working pressure. The term
CFM is used in this manual.
Circuit Breaker - A thermal switch that opens a circuit if too
much current is passing through it. The air compressor
motor is protected by this resettable device.
Cut-In Pressure – As air is taken from the air tank, the tank
air pressure drops. At a certain low level, the pressure switch
senses this low pressure and turns-on the compressor
motor, thus refilling the air tank. The level at which the motor
switches ON is called the cut-in pressure.
Cut-Out Pressure – While the compressor is running, air is
being produced and stored in the air tank. If no air is being
used, air pressure will build in the tank. The pressure switch
senses this high pressure and at a certain high level, it turns
the compressor motor off. The level at which the motor
switches OFF is called the cut-out pressure.
Duplex Receptacle - Two 120 volt AC receptacles that are
tied together. Similar to common household outlets.
GFCI - Ground fault current interrupter. A device that will
sense current flow in the milliamp range in a power circuit to
ground conductor and activate a relay to open both line
conductors.
Ground - A connection, either intentional or accidental,
between an electric circuit and the earth or some conducting
body serving in place of the earth.
Pressure Control – Often called a regulator, this device is
used to adjust the air compressor’s pressure output. The
pressure control is adjusted to supply the psi value required
by certain air tools, as monitored on the regulated pressure
gauge.
psi - pounds per square inch. The measure of air pressure
delivered by the air compressor system.
Single Stage - Single stage refers to an air compressor with
one or more cylinders that take air in each cylinder at the
down stroke and compresses the air into the air tank on the
up stroke.
Tank Pressure Gauge – A device used to indicate the air
pressure contained in the air tank, in psi.
Two Stage - A two-stage compressor always has a minimum
of two cylinders - a low pressure (LP) cylinder (largest) and
an high pressure (HP) cylinder (smallest). As the LP piston
goes downward, air is taken in at atmospheric pressure; on
the upward stroke the LP piston discharges the air through
an intercooler and into the HP cylinder on its downward
stroke. On the upward stroke of the HP piston the air is
discharged into the air tank. Two-stage compressors are
recommended when tool usage is continuous.
Vibration Isolators – When installed, are designed to
minimize vibrations produced by the air compressor.
18 BRIGGSandSTRATTON.COM
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC AIR COMPRESSOR OWNER WARRANTY POLICY
LIMITED WARRANTY
Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the air compressor that is defective in material or
workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This
warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in
our dealer locator map at BRIGGSandSTRATTON.COM.
THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW. ANY AND ALL IMPLIED WARRANTIES ARE
EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some
states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and
you may also have other rights which vary from state to state or country to country.
The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated above.
“Consumer use" means personal residential household use by a retail consumer. “Commercial use" means all other uses, including use for commercial,
income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be considered as commercial use for purposes of
this warranty.
NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE
RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING
DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.
ABOUT YOUR WARRANTY
We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty
repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if
equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the
warranty is void if the manufacturing date or the serial number on the air compressor has been removed or the equipment has been altered or modified.
During the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under
normal use and service. This warranty will not cover the following repairs and equipment:
Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not cover
repair when normal use has exhausted the life of a part or the equipment.
Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized installation or
alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as, in our judgment,
to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as air filters, adjustments, and so forth.
Other Exclusions: This warranty excludes wear items such as seals and o-rings, etc.This warranty also excludes air compressors that have been run
without oil or subjected to freezing with water in the tank(s). This air compressor is warranted for non-continuous use and should not be subjected to
continuous operation. Accessory parts, such as hoses or air tools not supplied with the compressor are excluded from the product warranty. This
warranty excludes failures due to acts of God and other force majeure events beyond the manufacturers control.
198183E, Rev. D, 12/31/2006
BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC
JEFFERSON, WI, USA
Effective October 1, 2005 replaces all undated Warranties and all Warranties dated before October 1, 2005
2 years
90 days
Consumer Use
Commercial Use
WARRANTY PERIOD
19
20 BRIGGSandSTRATTON.COM
Briggs & Stratton Power Products Group, LLC
900 N. Parkway
Jefferson, Wisconsin, 53549 U.S.A.
(800) 743-4115
Product Specifications
AC Frequency:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Hz
Rated AC Voltage: . . . . . . . . . . . . . . . . . 120 Volts, single phase
Pump Type: . . . . . . . . . . . . . . . . . . . Oil Lubricated Direct Drive
Lubricant:. . . . . . . . . . . . . . . . SAE 5W50 or 85W140 Synthetic
Oil Capacity: . . . . . . . . . . . . . . . . . . . . . . . . . 7.168 oz. (200ml)
Air Delivery:
At 40 psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0 CFM
At 90 psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0 CFM
Cut-In Pressure Setting: . . . . . . . . . . . . . . . . . 90 psi (6.2 bars)
Cut/Out Pressure Setting:. . . . . . . . . . . . . . . 125 PSI (8.7 bars)
Tank capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . 4 Gallons (15 L)
Tank Style: . . . . . . . . . . . . . . . . . . . . . . . . . . Twin Stack Vertical
Recommended Air Hose Size: . . . . . . . . . . 3/8 inch ID (14mm)
Air Fittings: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 inch NPT
Quick Connect Fitting Type: . . . . . . . . . . . . . . . . . . . . . . . . . I/M
Operating Temperature Range: . . . . 32° to 95°F (0° to + 35°C)
Shipping Weight: . . . . . . . . . . . . . . . . . . . . . . . . 62 lbs. (28 Kg)
Common Service Parts
Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200697GS
Air Compressor
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Briggs & Stratton 074007-0 Manuel utilisateur

Catégorie
Compresseurs d'air
Taper
Manuel utilisateur
Ce manuel convient également à