Whirlpool 8578566 Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire

Ce manuel convient également à

WASHER
Use & Care Guide
For questions about features, operation/performance,
parts, accessories or service, call: 1-800-253-1301.
In Canada, call: 1-800-807-6777
or visit our website at...
www.whirlpool.com or www.whirlpool.ca
LAVEUSE
Guide d’utilisation
et d’entretien
Au Canada, pour assistance, installation ou service, composez le
1-800-807-6777
ou visitez notre site web à
www.whirlpool.ca
Table of Contents/Table des matières ............... 2
8578566
®
2
TABLE OF CONTENTS
WASHER SAFETY ..........................................................................3
INSTALLATION REQUIREMENTS................................................4
Tools and Parts ............................................................................4
Options.........................................................................................4
Location Requirements................................................................5
Electrical Requirements ...............................................................6
INSTALLATION INSTRUCTIONS..................................................7
Before You Start...........................................................................7
Remove Transport System ..........................................................7
Drain System................................................................................7
Connect Drain Hose.....................................................................8
Connect the Inlet Hoses...............................................................8
Level the Washer..........................................................................9
Complete Installation ...................................................................9
WASHER USE...............................................................................10
Starting Your Washer.................................................................10
Using the Proper Detergent .......................................................10
Using the Dispenser...................................................................11
Controls......................................................................................12
Cycles.........................................................................................13
LAUNDRY TIPS ............................................................................14
Loading.......................................................................................14
WASHER CARE ............................................................................15
Cleaning Your Washer ...............................................................15
Water Inlet Hoses.......................................................................16
Vacation, Storage, and Moving Care.........................................16
TROUBLESHOOTING ..................................................................17
ASSISTANCE OR SERVICE.........................................................19
In the U.S.A. ...............................................................................19
In Canada ...................................................................................19
WARRANTY ..................................................................................20
TABLE DES MATIÈRES
SÉCURITÉ DE LA LAVEUSE........................................................22
EXIGENCES D'INSTALLATION...................................................23
Outillage et pièces......................................................................23
Options .......................................................................................24
Exigences d'emplacement.........................................................24
Spécifications électriques ..........................................................26
INSTRUCTIONS D’INSTALLATION.............................................27
Avant de commencer.................................................................27
Élimination des accessoires de transport..................................27
Système de vidange...................................................................28
Raccordement du tuyau d'évacuation.......................................28
Raccordement des tuyaux d'alimentation.................................29
Réglage de l'aplomb de la laveuse ............................................30
Achever l'installation ..................................................................30
UTILISATION DE LA LAVEUSE...................................................31
Mise en marche de la laveuse....................................................31
Utilisation du détergent approprié .............................................31
Utilisation du distributeur ...........................................................32
Commandes...............................................................................33
Programmes...............................................................................35
CONSEILS DE LESSIVAGE..........................................................36
Chargement................................................................................36
ENTRETIEN DE LA LAVEUSE .....................................................37
Nettoyage de la laveuse.............................................................37
Robinets d'arrivée d'eau ............................................................38
Précautions à prendre avant les vacances, un entreposage
ou un déménagement ................................................................38
DÉPANNAGE.................................................................................39
ASSISTANCE OU SERVICE.........................................................42
Aux États-Unis............................................................................42
Au Canada..................................................................................42
GARANTIE ....................................................................................43
®
3
WASHER SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.
These words mean:
follow instructions.
instructions.
DANGER
WARNING
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Read all instructions before using the washer.
Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
Do not add gasoline, dry-cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
this time.
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
Before the washer is removed from service or discarded,
remove the door or lid.
Do not reach into the washer if the drum, tub or agitator is
moving.
Do not install or store the washer where it will be exposed to
the weather.
Do not tamper with controls.
Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user-repair instructions that you understand and
have the skills to carry out.
See Electrical Requirements for grounding instructions.
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,
including the following:
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
The parts supplied are in the washer basket.
Tools needed:
Pliers that open to 1⁹⁄₁₆" (3.95 cm)
Flashlight (optional)
Adjustable or open end wrench ⁹⁄₁₆" (14 mm)
Level
Wood block
Utility knife
Measuring tape
T-20 TORX
®†
screwdriver
Phillips screwdriver
Parts supplied:
Alternate Parts
Your installation may require additional parts. For ordering
information, please refer to the Assistance or Service section of
this manual.
Options
Pedestal
You may order a pedestal separately for this washer. This
pedestal will add about 12" (30.48 cm) to the height of your unit
for a total height of approximately 45" (114.3 cm).
To order, call the dealer from whom you purchased your washer
or refer to the Assistance or Service section of this manual. Ask
for Model Number LAB0050PQ.
Stack Kit
Are you planning to stack your washer and dryer? To do so you
will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your washer
or refer to the Assistance or Service section of this manual. Ask
for Part Number 8182452.
A. U-shaped hose form
B. Water inlet hoses (2)
C. Inlet hose washers (2)
D. Inlet hose washers/screens (2)
E. Spoke with 4 clear plastic plugs
F. Black plastic plugs (2)
†®TORX is a registered trademark of Textron Innovations Inc.
ABC
D
E
F
If You Have: You Will Need to Buy:
Laundry tub or
standpipe taller
than 72" (183 cm)
Sump pump system (if not already
available)
1" (2.5 cm)
diameter
standpipe
2" (5 cm) diameter to 1" (2.5 cm)
diameter standpipe adapter,
Part Number 3363920
Overhead sewer Standard 20 gal. (76 L) 39" (99 cm) tall
drain tub or utility sink, sump pump and
connectors (available from local
plumbing suppliers)
Lint clogged drain Drain protector, Part Number 367031
Water faucets
beyond reach of
fill hoses
2 longer water fill hoses:
6 ft (1.8 m) Part Number 76314,
10 ft (3.0 m) Part Number 350008
Must also order: British to universal hose adapter,
Part Number 3357451
Installing new
water inlet hoses
British to universal hose adapter,
Part Number 3357451
Optional pedestal
5
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer walk.
Your washer can be installed in a basement, laundry room,
closet, or recessed area. See Drain System.
IMPORTANT: Do not install or store the washer where it will be
exposed to the weather.
Proper installation is your responsibility.
You will need:
A water heater set to deliver 120°F (49°C) water to the
washer.
A grounded electrical outlet located within 5 ft (1.5 m) of
where the power cord is attached to the back of the washer.
See Electrical Requirements.
Hot and cold water faucets located within 3½ ft (1.1 m) of the
hot and cold water fill valves, and water pressure of
20-100 psi (137.9-690 kPa).
A level floor with a maximum slope of ¾" (1.9 cm) under
entire washer. Installing the washer on carpeting is not
recommended.
A sturdy floor to support the washer weight (washer, water
and load) of 260 lbs (118 kg).
Do not store or operate your washer in temperatures at or below
32°F (0°C). Some water can remain in the washer and can cause
damage in low temperatures. See Washer Care for winterizing
information.
Installation Clearances
The location must be large enough to allow the washer door to
open fully.
Washer Dimensions
*Most installations require a minimum of 4" (10.16 cm) clearance
behind the washer for drain hose clearance. See Drain
System.
Installation spacing for recessed area and closet
installation
The following spacing dimensions shown are recommended
when the washer is to be operated with, or without, the Stack Kit.
This washer has been tested for installation with spacing of
0" (0 cm) clearance, however, spacing of 1" (2.5 cm) clearance is
recommended. Recommended spacing should be considered for
the following reasons:
Additional spacing should be considered for ease of
installation and servicing.
Additional clearances might be required for wall, door, and
floor moldings.
Additional spacing should be considered on all sides of the
washer to reduce noise transfer.
For closet installation with a door, minimum ventilation
openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.
Companion appliance spacing should also be considered.
Custom undercounter installation - Washer only
Recessed or closet installation - Washer only
33 ¼"
(84.45 cm
)
23 ³⁄₈ "
(59.37 cm)
38 ³⁄₄"
(98.43 cm)
23 ¹⁄₈"
(58.74 cm)
*
A. Side view - closet or confined area
B. Recessed area
C. Closet door with vents
0"
(0 cm
)
0"
(0 cm)
33¹⁄₄" min.
(84.45 cm)
23³⁄₈"
(59.37 cm)
B
A
4"
(10.16 cm)
14" (35.6 cm)
18" (45.7 cm)
0"
(0 cm)
0"
(0 cm)
48 in.
2
(310 cm
2
)
24 in.
2
(155 cm
2
)
3"
(7.6 cm)
3"
(7.6 cm)
C
1" (2.5 cm)
6
Recessed or closet installation - Stacked with stack kit
(Accessory)
Mobile Home - Additional Location Requirements
This washer is suitable for mobile home installations. The
installation must conform to the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 245, HUD Part 280).
Electrical Requirements
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical
supply is required. A time-delay fuse or circuit breaker is
recommended. It is recommended that a separate circuit
serving only this appliance be provided.
This washer is equipped with a power supply cord having a
3 prong grounding plug.
To minimize possible shock hazard, the cord must be
plugged into a mating, 3 prong, grounding-type outlet,
grounded in accordance with local codes and ordinances. If a
mating outlet is not available, it is the personal responsibility
and obligation of the customer to have the properly grounded
outlet installed by a qualified electrician.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that the
ground path is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure the
washer is properly grounded.
Do not have a fuse in the neutral or ground circuit.
A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
DRYER
WASHER
(30.5 cm)
12"
0" (0 cm)
0" (0 cm)
A
B
C
1" (2.5 cm)
48 in.
2
(310 cm
2
)
24 in.
2
(155 cm
2
)
3"
(7.6 cm)
3"
(7.6 cm)
3" (7.6 cm)
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
GROUNDING INSTRUCTIONS
For a grounded, cord-connected washer:
This washer must be grounded. In the event of a malfunction
or breakdown, grounding will reduce the risk of electrical
shock by providing a path of least resistance for electric
current. This washer is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local
codes and ordinances.
WARNING:
Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are in
doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician.
For a permanently connected washer:
This washer must be connected to a grounded metal,
permanent wiring system, or an equipment grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the appliance.
7
INSTALLATION INSTRUCTIONS
Before You Start
To avoid floor damage, set the washer onto cardboard before
moving across floor.
Using 2 or more people, move the washer to within
approximately 3 ft (90 cm) of its final location.
Remove Transport System
To install the machine, follow the steps below:
1. Move the machine to its installation position.
2. For transport reasons, the drum is locked in position. Loosen
the four transport bolts and remove them along with the
plastic splined and rubber spacers.
NOTE: If the plastic spacers cannot be removed from the
machine, call for service.
3. Next, loosen the two locking screws A and remove the two
bars B, as illustrated below. Keep the transport bolts,
screws, spacers and bars for future use.
4. Plug the holes with the 4 clear plastic plugs and 2 black
plastic plugs, packed inside the parts bag.
NOTE: If the washer is to be transported at a later date, call your
local service center.
Drain System
The washer can be installed using the standpipe drain system
(floor or wall), the laundry tub drain system, or the floor drain
system. Select the drain hose installation method you need. See
Tools and Parts.
Standpipe drain system - wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no less than
4.2 gal. (15.9 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm)
diameter standpipe adapter kit is available. See Tools and
Parts.
The top of the standpipe must be at least 23.5" (59.7 cm) high
and no higher than 72" (183 cm) from the bottom of the washer.
A. Plastic splined spacers (4)
B. Rubber spacers (4)
C. Flat washers (4)
D. Transport bolts (4)
WARNING
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.
A
B
C
D
A Screws (2)
B. Transport bars (2)
A. Clear plastic plugs (4)
B. Black plastic plugs (2)
A
B
A
B
AB
23.5 - 35"
(59.7 - 88.9 cm)
8
Laundry tub drain system (view C)
The laundry tub requires a minimum carry-away capacity of
4.2 gal. (15.9 L) per minute.
The top of the laundry tub must be at least 23.5" (59.7 cm) above
the floor and no higher than 72" (183 cm) from the bottom of the
washer.
Floor drain system (view D)
The floor drain system requires a siphon break that may be
purchased separately. See Tools and Parts.
The siphon break must be a minimum of 28" (71 cm) from the
bottom of the washer. Additional hoses might be needed.
The minimum carry-away capacity can be no less than 4.2 gal.
(15.9 L) per minute.
Connect Drain Hose
Proper connection of the drain hose will help protect your floors
from damage due to water leakage. To keep the drain hose from
coming off or leaking, it must be installed according to the
following instructions.
IMPORTANT: To ensure proper installation, this procedure must
be followed exactly.
For standpipe or laundry tub drain systems:
1. Check the drain hose to see that it is the proper length.
2. Install the U-shaped hose form to end of the drain hose to
create a hook-shaped end as shown.
3. Put hooked end of drain hose into laundry tub or standpipe.
See illustrations A and B.
If the washer faucets and the drain standpipe are recessed,
put the hooked end of the drain hose in the standpipe as
shown. See illustration C.
To keep drain water from going back into the washer:
Do not straighten hooked end of drain hose. Do not force
excess drain hose into standpipe. Hose should be secure,
but loose enough to provide a gap of air.
NOTE: To avoid siphoning, do not seal the drain hose to the
standpipe.
Do not lay excess drain hose in bottom of laundry tub.
Do not force excess drain hose back into the rear of the
washer.
For floor drain installation, see kit number required under
Tools and Parts.
Connect the Inlet Hoses
There are two hoses provided with the machine. The hot water
hose is indicated with a red stripe running the length of the hose.
Insert new flat washers (supplied) into the straight hose fitting of
each inlet hose. Firmly seat the washers in the couplings.
Connect the inlet hoses to the water faucets
Make sure the washer basket is empty.
1. Attach the hose with the red stripe to the hot water faucet.
Screw on coupling by hand until it is seated on the washer.
2. Attach the other hose to the cold water faucet. Screw on
coupling by hand until it is seated on the washer.
3. Using pliers, tighten the couplings with an additional
two-thirds turn.
NOTE: Do not overtighten. Damage to the valves can result.
A. Snap either end of the U-shaped hose form to the drain hose at the
point where the corrugation begins.
B. Bend drain hose over the form and snap into place.
23.5 - 35"
(59.7 - 88.9 cm)
CD
AB
A. Coupling
B. Washer
BC
A
AB
9
Clear the water lines
Run water through both faucets and inlet hoses, into a bucket or
laundry tub, to get rid of particles in the water lines that might
clog the inlet filter washers. The water should be clean, especially
where the system is new or has been left unused for a length of
time.
Connect the inlet hoses to the washer
1. Insert the filter washer (supplied) into the coupling of the hose
fitting elbow, before connecting the water inlet hose to the
valve on the back of the washer.
2. Attach the hose with the red stripe to the HOT (right) inlet
valve on the washer. Screw on coupling by hand until it is
seated on the washer. Make sure the hose connection is
tight.
NOTE: Do not overtighten. Damage to the valves can result.
3. Attach the other hose to the COLD water (left) inlet valve.
Screw on coupling by hand until it is seated on the washer.
Make sure the hose connection is tight.
NOTE: Do not overtighten. Damage to the valves can result.
Check for leaks
Turn on the water faucets and check for leaks. A small amount of
water might enter the washer. You will drain this later.
NOTE: Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Record hose installation or replacement dates for
future reference.
Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
Level the Washer
Properly leveling your washer averts excessive noise and
vibration.
1. Drape the power cord over the console.
2. Move washer to its final location. Remove any cardboard
used to move washer.
3. Check that the washer is level.
Check side to side and back to front by lining up the level
as shown in the following illustration.
4. If the washer is not level, prop up the front of the washer with
the wood block and adjust the feet up or down as necessary.
If the washer is against a wall, move the washer out slightly
before tipping back. Repeat this step until washer is level.
Complete Installation
1. Check the electrical requirements. Be sure that you have the
correct electrical supply and the recommended grounding
method. See Electrical Requirements.
2. Check that all parts are now installed. If there is an extra part,
go back through the steps to see which step was skipped.
3. Dispose of or recycle all packaging materials. Keep the
shipping bolts, spacers, and transport bars for use if the
washer should be transported.
4. Check that all the water faucets are completely on.
5. Check for leaks around faucets and inlet hoses.
6. Plug into a grounded 3 prong outlet.
7. Read Washer Use.
8. To test and to clean your washer, measure and add ¹⁄₂ the
normal recommended amount of High Efficiency (HE)
detergent to the washer. Close the door. Select any cycle,
and then press START. Allow it to complete one whole cycle.
A. Cold water inlet valve
B. Hot water inlet valve
B
A
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
10
WASHER USE
Starting Your Washer
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
The following is a guide to using your washer. Please refer to
specific sections of this manual for more detailed information.
Do not store laundry products on the top surface of this washer.
Vibration is normal during operation.
Using the Proper Detergent
Use only High Efficiency detergents. The package for this type of
detergent will be marked HE or High Efficiency. This wash
system, along with less water, will create too much sudsing with a
non-HE detergent. Using regular detergent will likely result in
washer errors, longer cycle times, and reduced rinsing
performance. It may also result in component failures and
noticeable mold or mildew odors. HE detergents are made to
produce the right amount of suds for the best performance.
Follow the manufacturer's instructions to determine the amount
of HE detergent to use.
First Wash Cycle Without Laundry
To clean the interior of the washer before washing clothes for the
first time, select the Regular/Normal cycle and run the washer
without clothes. Use ¹⁄₂ the normal recommended amount of
powdered or liquid HE detergent.
For All Wash Cycles
1. To load washer, open the washer door by pulling on the
handle. Sort laundry according to color and type of fabric.
Place a load of sorted clothes in the washer. Do not overload
washer. Overloading can cause poor cleaning.
The washer can be fully loaded, but not tightly packed.
Washer door should close easily.
Mix large and small items and avoid washing single items.
Load evenly.
Wash small items, such as infant socks, in mesh garment
bags. It is recommended that more than one garment bag
be used, and that each garment bag be filled with equal
amounts of material.
When unloading garments, occasionally check under the
gray seal/bellow between the door opening and the
basket for small items.
2. Close the washer door by pushing it firmly until the lock
clicks. The washer door will remain locked during the wash
cycle.
3. Open the dispenser drawer and add laundry products to the
detergent or fabric softener compartments. Close drawer
slowly to avoid spills. See Using the Dispenser.
IMPORTANT: Direct contact of chlorine bleach with clothing
can cause fabric damage. If you need extra whitening, use an
HE powdered detergent with bleach additive.
Fire Hazard
Never place items in the washer that are dampened
with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can result in death, explosion, or fire.
WARNING
A. Pre Wash detergent compartment
B. Main wash detergent compartment
C. Fabric softener compartment
AB
C
11
NOTES:
Use only HE detergents and follow label instructions.
Do not add detergent to the Pre Wash compartment
unless you have selected the Pre Wash option. If you
have detergent in both the Pre Wash and Main Wash
compartments, and have not selected a Pre Wash option,
the washer could oversuds. Suds could spill onto the
floor.
If you select the Pre Wash option, use powdered HE
detergent in the Main Wash compartment. If you use
liquid HE detergent in the Main Wash compartment, it will
dispense immediately.
Close the detergent drawer securely.
IMPORTANT: To avoid a water spill, do not open the
detergent drawer while the machine is operating.
4. Turn on the washer by selecting POWER.
5. Select one of the cycles by turning the cycle selector. The
preset settings provide the recommended fabric care for the
selected cycle. See Cycles.
6. Select the desired options. Not all options are available with
all cycles. See Cycles.
7. To begin the wash cycle, select START.
When the wash cycle is complete, the DONE status light
glows, the door unlocks, and the wash load can be
removed from the washer. To power down the washer
manually after the wash cycle is complete, press POWER
once.
Using the Dispenser
Your new washer has a dispenser drawer with three separate
compartments for your laundry productstwo are for detergent,
and one is for liquid fabric softener. Laundry products are diluted
and dispensed automatically at the proper time during the wash
cycle, making it unnecessary for you to return to the washer
during the cycle to add them.
It is normal for small amounts of water to remain in the
dispensers when the wash cycle is complete.
Do not put laundry additives directly into the wash tub. Always
use the proper dispensers when adding laundry products.
Choosing the Right Detergent
Use only High Efficiency detergents. The package for this type of
detergent will be marked HE or High Efficiency. This wash
system, along with less water, will create too much sudsing with a
regular non-HE detergent. Using regular detergent will likely result
in washer errors, longer cycle times and reduced rinsing
performance. It may also result in component failures and
noticeable mold or mildew odors. HE detergents are made to
produce the right amount of suds for the best performance.
Follow the manufacturer's instructions to determine the amount
of HE detergent to use.
To fill dispenser compartments
NOTE: Always use the detergent dispenser, and do not put
detergent directly onto clothes in the washer.
1. Pull out the dispenser drawer.
2. Add the desired laundry product to the proper compartment.
3. Push in the dispenser drawer slowly and completely (to avoid
spills).
Pre Wash detergent compartment
(Letter A in Dispenser Illustration)
Add HE detergent to this compartment when using the Pre Wash
option. Liquid or powdered HE detergent may be used in this
compartment. The detergent will automatically be dispensed
during Pre Wash if the Pre Wash option is selected.
Using HE detergent, add ¹⁄₃ the recommended amount to the
Pre Wash compartment and ²⁄₃ the recommended amount to
the Main Wash compartment.
IMPORTANT: If you are using the Pre Wash option, powdered HE
detergent must be used in the Main Wash compartment, since
liquid detergents may seep out of the Main Wash compartment
before the main wash begins.
Do not fill beyond the MAX level.
Main Wash detergent compartment
(Letter B in Dispenser Illustration)
Add liquid or powdered HE detergent to this compartment for
your main wash cycle.
IMPORTANT: If you are using the Pre Wash option, powdered HE
detergent must be used in the Main Wash compartment, since
liquid detergents may seep out of the Main Wash compartment
before the main wash begins.
Do not fill beyond the MAX level.
Fabric Softener compartment
(Letter D in Dispenser Illustration)
Add ¼ cup (60 mL) liquid fabric softener to this compartment.
Fabric softener will be automatically dispensed in the final rinse.
Do not fill beyond the MAX level.
Dispenser
A. Pre Wash detergent compartment
B. Main Wash detergent compartment
C. Dispenser drawer release lever
D. Fabric softener compartment
A
B
C
D
12
Controls
The control panel is simple to understand and easy to operate. The illustrations below define the knobs and buttons, and the
paragraphs define the purpose of each.
Power
This button switches the power to the machine on and off. After
Power is pressed, the Start button will flash.
Cycle Knob
Turn this knob to the desired cycle. The table in the Cycles
section defines each cycle in detail, so you can determine which
cycle is best for each type of load.
Stop Position
If you turn the Cycle Knob to Stop to interrupt a cycle, to add an
item or to cancel a cycle, there will be a 2-minute delay before the
door lock will release and you can open the door. To restart the
machine, you will have to reposition the Cycle Knob and press
the START button.
NOTE: Before the cycle will start, the machine will drain any
water already in the machine. Before you press START, it is a
good idea to make sure you do not need to add more detergent.
Status Lights
As the cycle progresses, the light for the cycle in progress will
glow. The Done indicator light glows when the cycle is complete.
At this point, there will be a 2-minute delay before the door lock
will release and you can open the door.
Spin Speed Knob
Use this knob to set the spin speed. In addition to the Low,
Medium, High and Extra High spin speeds, there is a No Spin
option. This is for delicate fabrics that should not be spun dry.
Extra Rinse Button
This button sets the cycle to add more rinsing. The button will
glow when this option is on. See "Cycles" for an explanation of
whether the rinse cycle can be added to each cycle. The regular
rinse cycle is usually sufficient, but if you live in an area with very
soft water or you are allergic to detergent, you may want to use
this option. This option is not available with Quick Wash or Spin.
Pre Wash
Press this button to select a Pre Wash. This is recommended only
for heavily soiled items. The button will glow when this option is
on. If you use Pre Wash, be sure to put detergent in the Pre Wash
compartment of the detergent drawer.
NOTE: Pre Wash cannot be selected for the Hand Wash, Quick
Wash or Spin cycles.
Start Button
After you have selected a cycle and options (Pre Wash or Extra
Rinse), press this button to start the cycle. The button will glow.
NOTE: A short time delay, up to a few minutes, may occur before
the wash cycle begins. This is a normal function of this washer.
13
Cycles
The table below defines each wash cycle in detail to help you determine which cycle is best for each type of load.
Cycles Temp
Soil
Level Fabrics Cycle Descriptions
Spin
Speed (1)
Options Available
Pre
Wash
Extra
Rinse
REGULAR
Heavy Soil Hot Heavy Cottons, linens Long main wash, 3 rinses,
Drain & Spin
Extra high Yes Yes
Whites Hot Heavy Cottons, linens,
blends, synthetics
Main wash, 3 rinses,
Drain & Spin
Extra high Yes Yes
Normal Warm Heavy Cottons, linens,
blends, synthetics
Main wash, 3 rinses,
Drain & Spin
Extra high Yes Yes
Color Cold Light Cottons, linens,
blends, synthetics
Main wash, 3 rinses,
Drain & Spin
Extra high Yes Yes
SYNTHETICS
Heavy Soil Hot Heavy Cottons, linens,
blends, synthetics
Long main wash, 3 rinses,
Drain & Spin
Extra high Yes Yes
Normal Warm Light Cottons, linens,
blends, synthetics
Main wash, 3 rinses,
Drain & Spin
Extra high Yes Yes
Color Cold Light Cottons, linens,
blends, synthetics
Main wash, 3 rinses,
Drain & Spin
Extra high Yes Yes
DELICATE
Hand Wash (2) Warm Light Machine-
washable wool,
silk, nylon
High-water level wash,
3 rinses, drain, gentle spin
Medium N/A Yes
Quick Wash Warm Light Machine-
washable wool,
silk, nylon
High-water level wash,
2 rinses, drain, gentle spin
Medium N/A N/A
Rinse Cold N/A All 3 fills, 3 drains, 3 tumbles,
1spin
Selectable N/A N/A
Spin N/A N/A Cottons, linens,
blends, synthetics
Drain and intensive spin Extra high N/A N/A
NOTES:
1. These are suggested spin speeds.
2. The Hand Wash cycle has a maximum 800 RPM spin speed to eliminate stress on delicate fabrics.
14
LAUNDRY TIPS
Preparing clothes for washing
Follow these recommendations to help you prolong the life of
your garments.
Use only High Efficiency detergents. The package for this
type of detergent will be marked HE or High Efficiency.
This wash system, along with less water, will create too much
sudsing with a regular non-HE detergent. Using regular
detergent will likely result in washer errors, longer cycle times
and reduced rinsing performance. It may also result in
component failures and noticeable mold or mildew odors. HE
detergents are made to produce the right amount of suds for
the best performance. Follow the manufacturer's instructions
to determine the amount of detergent to use.
To increase performance of this low-water washer, shake out
sand, dirt, and other matter before placing clothes and other
items into the washer.
Close zippers, snaps, and hooks to avoid snagging other
items. Remove pins, buckles, and other hard objects to avoid
scratching the washer interior. Remove non-washable trim
and ornaments.
Empty pockets and turn them inside-out.
Turn down cuffs; brush away lint and dirt.
Turn synthetic knits inside-out to avoid pilling.
Tie strings and sashes so they will not tangle.
Mend tears, loose hems, and seams.
Treat spots and stains.
Stained or wet garments should be washed promptly for best
results.
Mix large and small items, avoid washing single items, and
load evenly.
Use mesh garment bags to wash undergarments such as
underwire bras, items with strings, and small items such as
infant socks. It is recommended that more than one garment
bag be used, and that each garment bag be filled with equal
amounts of material.
Sorting
Separate heavily soiled items from lightly soiled ones, even if
they would normally be washed together. Separate lint-givers
(towels, chenille) from lint-takers (corduroy, synthetics,
permanent press). When possible, turn lint-givers inside-out.
Separate dark colors from light colors, colorfast items from
noncolorfast items.
Sort by fabric and construction (sturdy cottons, knits, delicate
items).
Unloading
Remove clothes from washer after the cycle is completed.
Metal objects such as zippers, snaps, and buckles may rust if
left in the washer basket for a long time.
When unloading garments, occasionally check under the gray
seal/bellow between the door opening and the basket for
small items.
Loading
Loading suggestions (maximum size loads)
Heavy Work Clothes
3 jeans
2work pants
3work shirts
Towels
8bath towels
8hand towels
10 washcloths
Permanent Press
1 double sheet
1dress
1blouse
2slacks
3shirts
6 handkerchiefs
Mixed Load
1 double sheet or twin
4 pillowcases
2shirts
2blouses
6T-shirts
6shorts
6 handkerchiefs
Knits
1pant
2blouses
4shirts
4tops
2dresses
Delicates
1camisoles
4slips
6 undergarments
1 set of sleepwear
15
WASHER CARE
Cleaning Your Washer
Cleaning the door seal
1. Open the washer door and remove any clothing or items from
the washer.
2. Inspect the gray seal/bellow between the door opening and
the basket for stained areas. Pull back the seal/bellow to
inspect all areas under the seal/bellow and to check for
foreign objects.
3. If stained areas are found, wipe down these areas of the seal/
bellows, using the procedure that follows.
a) Mix a dilute solution, using ³₄ cup (177.4 mL) of liquid
chlorine bleach, and 1 gal. (3.8 L) of warm tap water.
b) Wipe the seal/bellow area with the dilute solution, using a
damp cloth.
c) Let stand 5 minutes.
d) Wipe down area thoroughly with a dry cloth and let the
washer interior air dry with door open.
IMPORTANT:
Wear rubber gloves when cleaning for prolonged periods.
Refer to the bleach manufacturers instructions for proper
use.
Cleaning the interior
Use the following procedure without any clothing. Your washer
interior should be cleaned at least once per month to reduce or
avert any accumulation of mold or mildew odors.
1. Remove any clothing or items from the washer.
2. Open the dispenser drawer and add liquid chlorine bleach
into the Main Wash detergent compartment.
NOTE: Use 1 cup (236.6 mL) for first time cleaning. Use
¹⁄₃ cup (78.8 mL) for monthly maintenance.
3. Select and run the Regular/Heavy Soil cycle using hot water.
Repeat this process if necessary.
4. After cleaning, leave the washer door open slightly to allow
for better ventilation and drying of washer interior.
NOTE: To remove hard water deposits, use only cleaners labeled
for washer use.
Cleaning the exterior
Use a soft damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to keep it looking
new. Use mild soap and water. Do not use abrasive products.
Cleaning the dispenser drawer
The dispenser drawer is removable for easy cleaning.
1. Open the dispenser drawer. Unlock the dispenser drawer by
pressing on the plastic part of the softener compartment
marked PUSH. (Letter A in dispenser illustration.)
2. Remove the drawer.
3. To avoid damage to the finish, do not clean the drawer with
cleaning solvents or abrasive cleansers.
4. Replace the dispenser drawer in the washer.
Cleaning the lint filter
The lint filter should be cleaned about once a month. Make sure
the washer is not running before opening the filter door.
1. Place a pan or towel under the filter door, since a small
amount of water could spill. Open the filter door.
2. Remove the filter by rotating it a half-turn counterclockwise
and pulling outward.
A. Seal/Bellow
A
A. Dispenser drawer release
A
16
3. Clean the filter with a soft brush under running water until all
residue is removed.
4. Replace the filter and turn it clockwise until it is securely
locked in place. Give the cap a gentle tug to confirm that the
filter is secure.
5. Close the filter door.
Cleaning the control panel
To clean the control panel, use only a warm, damp cloth.
Do not spray water or cleaning solvents on the control panel.
Do not use abrasive cleaners or scouring pads on the outer
surfaces because they will scratch the finish and could
remove the writing on the control panel.
Some paper towels may also scratch the finish.
Water Inlet Hoses
Replace inlet hoses after five years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear or leaks are found.
When replacing your inlet hoses, record the date of replacement.
Vacation, Storage, and Moving Care
Install and store your washer where it will not freeze. Because
some water may stay in the hoses, freezing can damage your
washer. If storing or moving your washer during freezing weather,
winterize it.
Non-use or vacation care:
Operate your washer only when you are at home. If you will be on
vacation or not using your washer for an extended period of time,
you should:
Unplug washer or disconnect power.
Turn off the water supply to the washer. This helps avoid
accidental flooding (due to a water pressure surge) while you
are away.
Slightly open door to provide ventilation.
To winterize washer:
1. Put 1 qt (1 L) of R.V.-type antifreeze in the drum.
2. Run washer on a SPIN cycle.
3. Unplug washer or disconnect power.
4. Shut off both water faucets.
5. Disconnect water inlet hoses from faucets and drain.
To use washer again:
1. Flush water pipes. Reconnect water inlet hoses to faucets.
Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run the washer through the Regular/Normal cycle with
¹⁄₄ the normal recommended amount of HE detergent to clean
out antifreeze.
To transport the washer:
1. If washer will be moved during freezing weather, put in
1 qt (1 L) of R.V.-type antifreeze in the drum. Run washer on
a SPIN cycle.
2. Unplug the power cord.
3. Remove drain hose from the standpipe or laundry tub. Attach
the drain hose to the rear panel clips.
4. Shut off both water faucets.
5. Disconnect the water inlet hoses from faucets and rear of
washer. Drain the hoses and place them inside the washer
drum.
IMPORTANT: Call your local service center for assistance.
Transport bolts should be installed prior to moving. The washer
must be transported in the upright position to prevent suspension
and structural damage.
Reinstalling the washer:
1. Follow the Installation Instructions to locate, level and
connect the washer.
2. Run the washer through the Regular/Normal cycle with ¹⁄₄ the
normal recommended amount of HE detergent to clean the
washer and remove the antifreeze, if used.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
17
TROUBLESHOOTING
First try the solutions suggested here to possibly avoid the cost of a service call...
Washer odor
Do you use High Efficiency (HE) detergent?
Use only High Efficiency (HE) detergent in this washer.
Have you cleaned the washer interior using the
recommended procedure? Your washer interior should be
cleaned at least once per month to reduce or avoid any
accumulation of mold or mildew odors. See Washer Care
for interior cleaning procedure.
Inspect the interior of the washer for lint and other debris that
may accumulate on the basket and rubber bellows. Remove
and dispose of any accumulation as necessary.
Leave the washer door open between cycles to allow the
washer interior to dry out.
Washer wont start
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Is the washer door firmly closed?
Has a cycle been selected, but START has not been pressed?
Was the door open after completion of last cycle?
Washer wont fill, wash or rinse
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Is there power at the plug? Check electrical source or call
electrician.
Are the hot and cold water faucets turned on?
Is the water inlet hose kinked?
Are the water inlet valve screens clogged?
Washer stops
Check the following:
Is the power cord plugged into a grounded 3 prong outlet?
Is there power at the plug?
Check electrical source or call electrician.
Has a household fuse blown, or has a circuit breaker tripped?
Replace the fuse or reset the circuit breaker. If the problem
continues, call electrician.
Are you using an extension cord?
Do not use an extension cord.
Washer wont drain or spin
Is the drain hose clogged, or the end of the drain hose
more than 35" (88.9 cm) above the floor?
Is your voltage low?
Check electrical source or call electrician. Do not use an
extension cord.
Is the load balanced?
A single or bulky item may cause imbalance. Add more items
or redistribute the load.
Washer makes noise or vibrates
As water is drained from the washer, you may hear air being
pulled through the pump. This happens during the end of
draining. It is normal.
Is the washer level?
The washer must be level. The four feet should be properly
installed, and the nuts should be tightened against the
washer cabinet.
Did you remove the transport system?
Make sure four bolts and two bars have been removed. See
the Installation Instructions.
Are you washing items with metal snaps, buckles or
zippers?
You may hear metal items touching the washer drum. This is
normal.
Is washer installed on a sturdy and solid floor?
Refer to the Installation Requirements for flooring
requirements. Noise and vibration may be reduced by placing
a piece of ¾" (19.1 mm) plywood underneath your washer.
The plywood may extend underneath both washer and dryer
to keep them at equal heights.
Washer leaks
Check household plumbing for leaks.
Dispensers clogged or leaking
Are the laundry products in the correct dispenser
compartment?
Add the correct amounts of HE detergent or fabric softener to
the correct compartments.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
18
Load too wet
Did you use the right cycle for the load being washed?
Select a higher spin speed.
Did you wash a single item or bulky items or have you
overloaded the washer?
A single item, bulky items, or overloading may cause
imbalance. Add items or try to evenly distribute your wet
laundry in the drum, and select a Rinse & Spin cycle. If the
laundry is still wet, take half of the load out of the washer and
run this cycle again.
Residue or lint on load
Did you add detergent to the dispenser?
For best results, add detergent to the detergent
compartment. Do not add detergent to the washer drum.
Did you sort properly?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also, sort by color.
Did you overload the washer?
Do not overload the washer. The washer can be fully loaded,
but not tightly packed. The wash load must be balanced. Lint
can be trapped in the load if overloaded.
Check the following:
Was paper or tissue left in pockets?
Did you use enough HE detergent?
Use only HE or High Efficiency detergent. Follow detergent
manufacturers recommendations for the type of load you are
washing.
Is your water colder than 60°F (15.6°C)?
Wash water colder than 60°F (15.6°C) may not completely
dissolve powdered detergent.
Are you using a low speed wash cycle?
Powdered detergents may not dissolve well in a slow-speed
cycle. For best results, use liquid detergent for slow-speed
cycles such as Hand Wash.
Stains on load
Did you add detergent to the dispenser?
For best results, add detergent to the detergent
compartment. Do not add detergent to the washer drum.
Did you use enough HE detergent?
Use only
HE or High Efficiency detergent. Follow detergent
manufacturers recommendations for the type of load you are
washing.
Is there above average iron (rust) in water?
You may need to install an iron filter.
Did you properly sort the load?
Sort dark clothes from whites and lights.
Did you unload the washer promptly?
To avoid dye transfer, unload the washer as soon as it stops.
Did you use a fabric softener dispensing ball?
Dispensing balls will not operate correctly with this washer.
Add liquid fabric softener to the fabric softener compartment.
Did you use powdered detergent in a low-speed cycle?
Powdered detergents may not dissolve well in a slow-speed
cycle. For best results, use liquid detergent for slow-speed
cycles such as Hand Wash.
Load is wrinkled
Did you unload the washer promptly?
Unload the washer as soon as it stops.
Did you use the right cycle for the load being washed?
Use the Hand Wash cycle or another cycle with a low spin
speed to reduce wrinkling.
Did you overload the washer?
The wash load must be balanced and not overloaded. Loads
should tumble freely during washing.
Gray whites, dingy colors
Did you properly sort the load?
Dye transfer can occur when mixing whites and colors in a
load. Sort dark clothes from whites and lights.
Was the wash temperature too low?
Use hot or warm washes if safe for the load. Make sure your
hot water system is adequate to provide a hot water wash.
Did you use enough detergent, or do you have hard
water?
Use more detergent for washing heavy soils in cold or hard
water.
Cycle too long
Did you select the Hand Wash wash cycle?
When using the Hand Wash cycle, you should use small
loads. This ensures a gentle wash for your garments without
increasing cycle times.
Did you wash a large load using a gentle cycle?
When using the Hand Wash cycle, use small loads. This
ensures a gentle wash for your garments without increasing
cycle times.
Door locked at end of wash cycle
Did all of the water drain out of the washer during the
spin?
Select Rinse & Spin to remove any water remaining in the
washer. The washer door will unlock 2 minutes after the end
of Spin.
Did you attempt to open the door immediately after the
washer stopped?
There is a 2-minute delay at the end of the cycle, before you
can open the door. This is normal.
19
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
Troubleshooting. It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
only use factory specified parts. These parts will fit right and work
right because they are made with the same precision used to
build every new WHIRLPOOL
®
appliance.
To locate replacement parts in your area:
In the U.S.A., call the Customer eXperience Center at
1-800-253-1301, or your nearest designated service center.
In Canada, call 1-800-807-6777, or your nearest designated
service center.
In the U.S.A.
Call the Whirlpool Customer eXperience Center toll free:
1-800-253-1301.
Our consultants provide assistance with:
Features and specifications on our full line of appliances
Installation information
Use and maintenance procedures
Accessory and repair parts sales
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.)
Referrals to local dealers, repair parts distributors, and
service companies
Whirlpool designated service technicians are trained to fulfill the
product warranty and provide after-warranty service anywhere in
the United States.
To locate the Whirlpool designated service company in your area,
you can also look in your telephone directory Yellow Pages.
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
Whirlpool Corporation
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada
Call the Whirlpool Canada LP Customer Interaction Centre toll
free: 1-800-807-6777.
Our consultants provide assistance with:
Features and specifications on our full line of appliances.
Use and maintenance procedures.
Accessory and repair parts sales.
Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool Canada LP designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service anywhere in Canada.
For further assistance
If you need further assistance, you can write to Whirlpool
Canada LP with any questions or concerns at:
Customer Interaction Centre
Whirlpool Canada LP
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY
ONE YEAR LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for FSP
®
replacement parts
and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.
ITEMS WHIRLPOOL WILL NOT PAY FOR
1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair
house fuses or to correct house wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty
coverage.
3. Repairs when your major appliance is used for other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.
5. Any food loss due to refrigerator or freezer product failures.
6. Replacement parts or repair labor costs for units operated outside the United States or Canada.
7. Pickup and delivery. This major appliance is designed to be repaired in the home.
8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
9. Expenses for travel and transportation for product service in remote locations.
10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE
TO PROVINCE.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if
another warranty applies.
If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help
can be found by checking the “Assistance or Service” section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada,
call 1-800-807-6777. 8/05
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name____________________________________________________
Address ________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Whirlpool 8578566 Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues