Simplicity 030338-00 Manuel utilisateur

PRO10000 Portable Generator

Operator’s Manual

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WISCONSIN, U.S.A.

Manual No. 204730GS Revision B (03/13/2009)

This generator is rated and certified to be compliant with CSA (Canadian

Standards Association) standard C22.2 No. 100-04 (motors and generators).

2 BRIGGSandSTRATTON.COM

Briggs & Stratton Power Products Group, LLC

900 North Parkway

Jefferson, WI 53549

may be reproduced or transmitted in any form by any means

without the express written permission of Briggs & Stratton

Power Products Group, LLC.

Thank you for purchasing this quality-built Briggs & Stratton generator. We are pleased that you’ve placed your confidence in

the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual, your Briggs &

Stratton generator will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with generator products and

how to avoid them. This generator is designed and intended only for supplying electrical power for operating compatible

electrical lighting, appliances, tools and motor loads, and is not intended for any other purpose. It is important that you read

and understand these instructions thoroughly before attempting to start or operate this equipment. Save these instructions

for future reference.

This generator requires final assembly before use. Refer to the Assembly section of this manual for instructions on final

assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow Pages. There

are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also contact

Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at BRIGGSandSTRATTON.COM.

Generator

Model Number

Revision

Serial Number

Engine

Model Number

Type Number

Code Number

Date Purchased

3

Table of Contents

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpack Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Shipment Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Install Wheel Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Add Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Add Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

System Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting to a Building’s Electrical System. . . . . . . . . . . . . . . . . . . . . . . 10

Generator Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Cord Sets and Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Ground Fault Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Battery Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Connecting Electrical Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Stopping the Engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Operating Automatic Idle Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Oil Pressure Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Charging a Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Cold Weather Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Don’t Overload Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Generator Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Fuel Valve Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Engine Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Warranties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Emissions Control System Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Generator Owner Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Common Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

3

Operator Safety

Equipment Description

Read this manual carefully and become familiar

with your generator. Know its applications, its

limitations and any hazards involved.

The generator is an engine–driven, revolving field, alternating

current (AC) generator. It was designed to supply electrical

power for operating compatible electrical lighting,

appliances, tools and motor loads. The generator’s revolving

field is driven at about 3,600 rpm by a twin-cylinder engine.

This generator incorporates GFCI (Ground Fault Circuit

Interrupter) outlet protection and has its neutral bonded to

ground to comply to OSHA inspections on job sites. This

generator will not function when connected to a 2 pole

transfer switch since the home or building main breaker box

also has a neutral bonded to ground. When both the

generator and the home or building breaker box contains a

neutral bonded to ground, the generators GFCI will open and

no outlets will function.

NOTICE

Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

Every effort has been made to ensure that the information in

this manual is both accurate and current. However, the

manufacturer reserves the right to change, alter or otherwise

improve the generator and this documentation at any time

without prior notice.

The Emission Control System for this generator is warranted

for standards set by the Environmental Protection Agency

and the California Air Resources Board.

Important Safety Information

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that the

procedure, work method or operating technique that you

choose does not render the generator unsafe.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol may

be used to represent the type of hazard. The signal word

NOTICE is used to address practices not related to personal

injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE address practices not related to personal injury.

4 BRIGGSandSTRATTON.COM

WARNING

Removing the neutral bond could result in

death, bodily injury and/or property damage.

• DO NOT remove the neutral bond.

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Kickback

Flying Objects

Operator’s Manual

Explosive Pressure

Chemical Burn

5

WARNING

Storage batteries give off explosive

hydrogen gas during recharging.

Hydrogen gas stays near battery for a

long time after battery has been charged.

Slightest spark will ignite hydrogen and cause explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is extremely

caustic.

Contact with battery fluid will cause severe chemical burns.

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate generator ONLY outdoors.

• Install a battery operated carbon monoxide alarm near the

bedrooms.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

(even if windows and doors are open), including the generator

compartment of a recreational vehicle (RV).

WARNING The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING Certain components in this product and

related accessories contain chemicals known to the State

of California to cause cancer, birth defects or other

reproductive harm. Wash hands after handling.

WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand

and arm toward engine faster than you can let

go.

Broken bones, fractures, bruises, or sprains could result.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe

burns or death.

WHEN ADDING OR DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in

place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• This generator is not for use in mobile equipment or marine

applications.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff valve

OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other ignition

source because they can ignite fuel vapors.

WARNING

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in death or serious injury and/or property

damage.

NOTICE

Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

NOTICE

Improper treatment of generator can damage it

and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or contact

local service center.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect them

from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

6 BRIGGSandSTRATTON.COM

WARNING

Generator produces hazardous voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

• When using generator for backup power, notify utility company.

Use approved transfer equipment to isolate generator from

electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

WARNING Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING Starter and other rotating parts can

entangle hands, hair, clothing, or accessories.

• NEVER operate generator without protective housing or covers.

• DO NOT wear loose clothing, jewelry or anything that may be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

CAUTION

Excessively high operating speeds increase

risk of injury and damage to generator.

Excessively low speeds impose a heavy load.

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Assembly

Your generator requires some assembly and is ready for use

after it has been properly serviced with the recommended oil

and fuel.

If you have any problems with the assembly of your generator,

please call the generator helpline at 1-800-743-4115. If calling

for assistance, please have the model, revision, and serial

number from the identification label available. See Generator

Controls and Features for identification label location.

Unpack Generator

1. Set the carton on a rigid, flat surface.

2. Remove everything from carton except generator.

3. Open carton completely by cutting each corner from

top to bottom.

4. Leave generator on carton to install wheel kit.

Shipment Contents

The generator is supplied with:

• Engine oil

• Operator’s manual

• Battery float charger

• Battery charge cables

• Wheel kit

• 120/240 Volt, 30 Amp locking plug

• 120 Volt, 30 Amp locking plug

Install Wheel Kit

NOTE: Wheel kit is not intended for over-the-road use.

You will need the following tools to install these

components:

• 3/8” and 13 mm wrench

• Socket wrench with a 3/8” and 13 mm socket

• Pliers

• Safety glasses

Install the wheel kit as follows:

1. Tip generator so that engine side is down.

2. Slide axle (A) through both mounting brackets.

3. Slide a wheel (B) over axle.

NOTE: Be sure to install wheel with raised hub inboard.

4. Place a washer (C) on axle and then place an e-ring (D)

in axle groove.

5. Install e-ring with pliers, squeezing from top of e-ring

to bottom of axle.

6. Repeat steps 3 through 5 to secure second wheel.

7

N

E

D

A

H

C

M

J

K

L

G

B

F

CAUTION

E-rings can cause eye injury.

E-rings can spring back and become airborne

when installing or removing.

• Always wear eye protection when installing/removing e-rings.

7. Tip generator so that engine end is up.

8. Attach clamps (E) to brackets (F) on both sides of

generator with 1/4 - 20 hex screws (G).

9. Repeat steps 2 through 5 to secure the third and fourth

wheels.

10. Attach handles (H) to brackets on generator frame as

shown, with 45 mm capscrews (J), flat washers (K),

nylon washers (L), and M8 lock nuts (M).

NOTE: DO NOT overtighten. Handles must be able to move

up and down freely.

11. Return generator to normal operating position (resting

on wheels).

12. To apply brakes, push down firmly on handle of both

clamps until it locks in the down position and engages

the wheels.

IMPORTANT: The generator is designed to be used on level

surfaces.

13. Loop handle pins (N) on generator frame just above

handle brackets.

14. Raise handles and insert handle pins to move

generator.

15. To release brakes, pull up on handle of both clamps

until it locks in the up position.

Attach Negative Battery Cable

Your unit is equipped with electric start capability but can be

started manually. If you choose not to use the electric start

feature, you do not need to connect the negative battery

cable.

The sealed battery on the generator pre–installed except for

the negative (black) battery cable.

To install:

1. Cut off tie wrap securing loose end of negative (black)

cable.

2. Using an 8 mm or 5/16” socket wrench, remove

screw (A), lock washer (B) and flat washer (C) on

negative battery terminal.

3. Slide lock washer, flat washer and negative battery cable

(D) over screw as shown.

4. Reattach screw to negative battery terminal and tighten.

5. Verify that connections to battery and generator are

tight and secure.

NOTE: If your battery is discharged, charge prior to use

following the instructions in the section Battery Charger.

8 BRIGGSandSTRATTON.COM

A

D

C

B

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds - chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

Add Engine Oil

1. Place generator on a flat, level surface.

2. Clean area around oil fill and remove yellow oil fill cap.

3. Using oil funnel (optional), slowly pour contents of

both provided oil bottles into oil fill opening to the

“Full” mark on dipstick.

NOTICE

Improper treatment of generator can damage it

and shorten its life.

• DO NOT attempt to crank or start the engine before it has been

properly serviced with the recommended oil. This may result in an

engine failure.

4. Replace oil fill cap and fully tighten.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). For high

altitude use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) or up to

15% MTBE (methyl tertiary butyl ether) is acceptable.

NOTICE Avoid generator damage.

Failure to follow Operator’s Manual for fuel

recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gum formation, mix in a fuel

stabilizer when adding fuel. See Storage. All fuel is not the

same. If you experience starting or performance problems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operate on gasoline. The

emission control system for this engine is EM (Engine

Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add unleaded gasoline (A) to fuel tank (B). Be

careful not to fill above the baffle (C). This allows

adequate space for fuel expansion as shown.

3. Install fuel cap and let any spilled fuel evaporate before

starting engine.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable. To

remain emissions compliant, high altitude adjustment is

required. Operation without this adjustment will cause

decreased performance, increased fuel consumption, and

increased emissions. See an authorized dealer for high

altitude adjustment information. Operation of the engine at

altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

FUEL

TANK

C

B

A

9

WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe

burns or death.

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals on the

AC output receptacles. The system ground is connected to

the AC neutral wire (the neutral is bonded to the generator

frame).

Special Requirements

There may be Federal or State Occupational Safety and

Health Administration (OSHA) regulations, local codes, or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction:

• In some areas, generators are required to be registered

with local utility companies.

• If the generator is used at a construction site, there

may be additional regulations which must be observed.

Connecting to a Building’s Electrical System

Connections for standby power to a building’s electrical

system must be made by a qualified electrician. The

connection must isolate the generator power from utility

power or other alternative power sources and must comply

with all applicable laws and electrical codes.

Generator Location

Clearances and Air Movement

Place generator outdoors in an area that will not accumulate

deadly exhaust gas. DO NOT place generator where exhaust

gas (A) could accumulate and enter inside or be drawn into

a potentially occupied building. Ensure exhaust gas is kept

away from any windows, doors, ventilation intakes, or other

openings that can allow exhaust gas to collect in a confined

area. Prevailing winds and air currents should be taken into

consideration when positioning generator.

10 BRIGGSandSTRATTON.COM

A

WARNING

Generator produces hazardous voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

• When using generator for backup power, notify utility company.

Use approved transfer equipment to isolate generator from

electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

WARNING Exhaust heat/gases can ignite

combustibles, structures or damage fuel tank

causing a fire.

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

Features and Controls

Read this Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

11

A - Fuel Tank — Capacity of seven (7) U.S. gallons (26.5 l).

B - Oil Filter — Filters engine oil to prolong engine life.

C - Spark Arrester Muffler — Exhaust muffler lowers engine

noise and is equipped with a spark arrester screen.

D - Recoil Starter — Used to start the engine manually.

E - Engine Identification — Provides model, type and code

of engine. Please have these readily available if calling for

assistance.

F - Choke Control — Used when starting a cold engine.

G - Air Cleaner — Protects engine by filtering dust and

debris out of intake air.

H - Start Switch — Push to start the engine.

J - Battery Float Charger Jack — Use battery float charger

jack to keep the starting battery charged and ready for

use.

A

C

F

G

J

H

E

D

B

12 BRIGGSandSTRATTON.COM

A - Oil Fill Cap — Fill engine with oil here.

B - Oil Dipstick — Check engine oil here.

C - Fuel Valve — Used to turn fuel supply on and off to

engine.

D - Oil Drain Plug — Drain engine oil here.

E - Hour Meter — Displays and records how many hours

your generator has run (up to 9,999.9).

F - Grounding Fastener — Consult your local agency having

jurisdiction for grounding requirements in your area.

G - Identification Label — Provides model and serial

number of generator. Please have these readily available

if calling for assistance.

H - GFCI Circuit Breaker — A GFCI circuit breaker is

provided to protect against electrical ground fault and

protect the generator against electrical overload.

J - 120/240 Volt AC, 50 Amp Receptacle — May be used to

supply electrical power for the operation of 120 and/or

240 Volt AC, 50 Amp, single phase, 60 Hz electrical

loads.

K - 120/240 Volt AC, 30 Amp Locking Receptacle — May

be used to supply electrical power for the operation of

120 and/or 240 Volt AC, 30 Amp, single phase, 60 Hz

electrical, lighting, appliance, tool and motor loads.

L - 120 Volt AC, 30 Amp Locking Receptacle — May be

used to supply electrical power for the operation of

120 Volt AC, 30 Amp, single phase, 60 Hz electrical

lighting, appliance, tool and motor loads.

M - 120 Volt AC, 20 Amp, Duplex Receptacle — May be

used to supply electrical power for the operation of

120 Volt AC, 20 Amp, single phase, 60 Hz electrical,

lighting, appliance, tool and motor loads.

N - 12 Volt DC Receptacle — Use this receptacle with

battery charge cables to charge a 12 Volt battery. This

receptacle is protected by a 10 Amp auto reset circuit

breaker.

P - Rocker Switch Circuit Breaker — The 120/240 Volt AC,

30A locking receptacle and the 120 Volt AC, 30A locking

receptacle is provided with a 2 pole rocker switch circuit

breaker to protect the generator against electrical

overload.

R - Idle Control Switch — Use this switch to turn the idle

control feature on and off.

S - Run/Stop Switch — Set this switch to "Run" before

starting. Set switch to "Stop" to switch off engine.

T - Circuit Breakers (AC) — The 120 Volt AC, 20A duplex

receptacle is provided with "push to reset" circuit

breakers to protect the generator against electrical

overload.

A

B

C

D

J

H

S

R

F

N

K

L

M

P

T

G

E

Cord Sets and Receptacles

Use only high quality, well-insulated, grounded extension

cords with the generator’s 120 Volt duplex receptacle.

Inspect extension cords before each use.

Check the ratings of all extension cords before you use

them. Extension cord sets used should be rated for 125 Volt

AC loads at 20 Amps or greater for most electrical devices.

Some devices, however, may not require this type of

extension cord. Check the operator’s manuals of those

devices for the manufacturer’s recommendations.

Keep extension cords as short as possible to minimize

voltage drop.

120/240 Volt AC, 50 Amp Receptacle

Use a NEMA 14–50 plug with this receptacle. Connect a

4-wire cord set rated for 250 Volt AC loads at 50 Amps to

the plug.

This receptacle powers 120/240 Volt AC, 60 Hz, single phase

loads requiring up to 10,000 watts of power (10.0 kW) at

41.6 Amps for 240 Volts or two independent 120 Volt loads.

The outlet is protected by a 2 pole GFCI circuit breaker.

NOTICE

Receptacles may be marked with rating value

greater than generator output capacity.

• NEVER attempt to power a device requiring more amperage than

generator or receptacle can supply.

• DO NOT overload the generator. See Don’t Overload Generator.

120/240 Volt AC, 30 Amp, Locking Receptacle

Use a NEMA L14-30 plug with this receptacle. Connect a

4-wire cord set rated for 250 Volt AC loads at 30 Amps (or

greater). You can use the same 4-wire cord if you plan to run

a 120 Volt load.

This receptacle powers 120/240 Volt AC, 60 Hz, single phase

loads requiring up to 7,200 watts of power (7.2 kW) at

30 Amps for 240 Volts or two independent 120 Volt loads at

30 Amps each. The outlet is protected by a rocker switch

circuit breaker and/or a 2 pole GFCI circuit breaker.

120 Volt AC, 30 Amp Locking Receptacle

Use a NEMA L5–30 plug with this receptacle. Connect a

3–wire cord set rated for 125 Volt AC loads at 30 Amps to

the plug.

Use this receptacle to operate 120 Volt AC, 60 Hz, single

phase loads requiring up to 3,600 watts (3.6 kW) of power at

30 Amps. The outlet is protected by a rocker switch circuit

breaker and/or a 2 pole GFCI circuit breaker.

WARNING

Overloaded electrical cords can overheat,

arc, and burn resulting in death, bodily injury,

and/or property damage.

• ONLY use cords rated for your loads.

• Follow all safeties on electrical cords.

13

4-Wire Cord Set

240V

120V

NEMA L14-30

W (Neutral)

X (Hot)

Y (Hot)

Ground (Green)

120 Volts

AC

120 Volts

AC

X (Hot)

Y (Hot)

240 Volts AC

Frame Ground

NEMA 14-50

W (Neutral)

3-Wire Cord Set

Neutral

120V

Hot

Ground (Green)

NEMA L5-30

120 Volt AC, 20 Amp, Duplex Receptacles

The duplex receptacle is protected against overload by a

push–to–reset circuit breaker and/or a 2 pole GFCI circuit

breaker.

Use each receptacle to operate 120 Volt AC, single-phase,

60 Hz electrical loads requiring up to 2,400 watts (2.4 kW) at

20 Amps of current. Use cord sets that are rated for 125 Volt

AC loads at 20 Amps (or greater). Inspect cord sets before

each use.

12 Volt DC, 10 Amp Receptacle

This receptacle allows you to recharge a 12 Volt automotive

or utility style storage battery with the battery charge cables

provided.

This receptacle can not recharge 6 Volt batteries and can not

be used to crank an engine having a discharged battery. See

the section Charging a Battery before attempting to recharge

a battery.

Ground Fault Protection

This unit is equipped with a Ground Fault Circuit Interrupter

(GFCI). This device meets applicable federal, state and local

codes.

The GFCI protects against electrical shock that may be

caused if your body becomes a path which electricity travels

to reach ground. This could happen if you touch a “Live”

appliance or wire, or are touching plumbing or other

materials that connect to the ground.

When protected by a GFCI, one may still feel a shock, but the

GFCI should cut current off quickly enough so that a person in

normal health should not suffer any serious electrical injury.

Test GFCI Circuit Breaker

Test your GFCI circuit breaker every month, as follows:

1. While generator is running, push white “Test” button.

The circuit breaker should trip (handle will move to

approximate center position), which will disconnect

power to outlets.

2. If handle moves to center, reset circuit breaker by

firmly moving handle to “Off” (down) position, then to

“On” (up) position.

14 BRIGGSandSTRATTON.COM

CAUTION

If circuit breaker does not trip:

• DO NOT use generator.

• Call a Briggs & Stratton Power Products service center.

WARNING

Generator produces hazardous

voltage/current.

• The GFCI will not protect you against the following situations:

-Line-to-line shocks;

-Current overloads or line-to-line short circuits.

• The fuse or circuit breaker at the control panel must provide

such protection.

CAUTION

If circuit breaker does not reset properly:

• DO NOT use generator.

• Call a Briggs & Stratton Power Products service center.

During Generator Use

If circuit breaker trips during use, it usually indicates faulty

electrical equipment or cords. However, test the circuit

breaker as follows;

1. Disconnect loads, reset and test circuit breaker as

described earlier. Let generator run without any loads

for 1 minute.

2. If circuit breaker tests correctly, the electrical equipment

or extension cords may be faulty. Replace faulty

electrical equipment and cords before further use.

Battery Charger

Use battery float charger jack to keep the starting battery

charged and ready for use. Battery charging should be done in a

dry location, such as inside a garage.

1. Plug charger into unit’s “Battery Float Charger” jack,

which is located next to the start switch. Plug battery

charger into a 120 Volt AC wall receptacle.

2. Unplug charger from unit and wall outlet when generator

is being started and while it is in operation.

3. Keep this charger plugged in when generator is not in

use to prolong battery life. The charger has a built in

float equalizer and will not overcharge the battery, even

when plugged in for an extended period of time.

IMPORTANT: See Battery Maintenance for additional

information.

15

WARNING

Generator produces hazardous

voltage/current.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator or electrical loads.

CAUTION

If circuit breaker trips in the 1 minute

period:

• DO NOT use generator.

• Call a Briggs & Stratton Power Products service center.

CAUTION

If circuit breaker tests correctly:

• Have qualified personnel check all electrical equipment and

cords for any defects.

• Replace electrical equipment and cords or take to a qualified

repair center.

Operation

Starting the Engine

IMPORTANT: Always unplug the battery float charger before

starting the generator.

Disconnect all electrical loads from the generator. Use the

following start instructions:

1. Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate the unit on a level

surface will cause the unit not to start or shut down during

operation.

2. Turn the fuel valve (A) to the “On” position.

3. Make sure idle control switch is in “Off” position.

4. Set run/stop switch to “Run” position.

5. Pull choke control out to close choke.

6A. For electric starting, push and hold the start switch in

“Start” position until generator starts. To prolong the

life of starter components, DO NOT hold start switch in

“Start” position for more than 15 seconds, and pause

for at least 1 minute between starting attempts.

• If engine starts, proceed to step 8.

• If engine fails to start, proceed to step 7.

NOTE: If battery is discharged, use manual starting instructions.

6B. For manual starting, grasp recoil handle and pull

slowly until slight resistance is felt. Then pull rapidly

one time only to start engine.

• If engine starts, proceed to step 8.

• If engine fails to start, proceed to step 7.

7. Push in the choke handle half way, and pull recoil

handle twice or push and hold the start switch in the

“Start” position as described in step 6A.

• If engine fails to start, repeat steps 5 thru 6.

8. Open the choke gradually as the engine warms up by

pushing in on the choke handle.

IMPORTANT: If engine floods, push choke handle all the way

in and crank until engine starts.

NOTE: If engine starts after 3 pulls but fails to run, or if unit

shuts down during operation, make sure unit is on a level

surface and check for proper oil level in crankcase. This unit

may be equipped with a low oil protection device. If so, oil

must be at proper level for engine to start.

Connecting Electrical Loads

1. Let engine stabilize and warm up for a few minutes

after starting.

2. Plug in and turn on the desired 120 and/or 240 Volt

AC, single phase, 60 Hz electrical loads.

NOTE:

• DO NOT connect 240 Volt loads to the 120 Volt duplex

receptacles.

• DO NOT connect 3-phase loads to the generator.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

16 BRIGGSandSTRATTON.COM

A

WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand

and arm toward engine faster than you can let

go.

Broken bones, fractures, bruises, or sprains could result.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR. See Don’t

Overload Generator.

NOTICE

Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

Stopping the Engine

1. Turn OFF and unplug all electrical loads from generator

panel receptacles. NEVER start or stop engine with

electrical devices plugged in and turned ON.

2. Move idle control switch to “Off” position.

3. Let engine run at no-load for several minutes to

stabilize internal temperatures of engine and generator.

4. Push run/stop switch to “Stop” position.

5. Move fuel valve to “Off” position.

Operating Automatic Idle Control

This feature is designed to greatly improve fuel economy.

When this switch is turned ON, the engine will only run at

its normal high governed engine speed when electrical loads

are connected. When electrical loads are removed, the

engine will run at a reduced speed.

With the switch off, the engine will run at the normal high

engine speed. Always have the switch off when starting and

stopping the engine.

Oil Pressure Shutdown

If engine oil pressure drops below a preset level, an oil

switch will stop the engine. Check oil level with dipstick.

If oil level is between ADD and FULL mark on dipstick:

1. DO NOT try to restart the engine.

2. Contact an Authorized Briggs & Stratton Service Dealer.

3. DO NOT operate engine until oil pressure is corrected.

If oil level is below ADD mark on dipstick:

1. Add oil to bring level to FULL mark.

2. Restart engine and if the engine stops again a low oil

pressure condition may still exist. DO NOT try to restart

the engine.

3. Contact an Authorized Briggs & Stratton Service Dealer.

4. DO NOT operate engine until oil pressure is corrected.

Charging a Battery

Your generator has the capability of recharging a discharged

12 Volt automotive or utility style storage battery.

• DO NOT use the unit to charge any 6 Volt batteries.

• DO NOT use the unit to crank an engine having a

discharged battery.

To recharge 12 Volt batteries, proceed as follows:

1. Check fluid level in all battery cells. If necessary, add

ONLY distilled water to cover separators in battery

cells. DO NOT use tap water.

2. If battery is equipped with vent caps, make sure they

are installed and are tight.

3. If necessary, clean battery terminals.

4. Connect battery charge cable connector plug to panel

receptacle identified by the words “12V 10A D.C.”

5. Connect battery charge cable clamp with red handle to

the positive (+) battery terminal.

6. Connect battery charge cable clamp with black handle

to the negative (–) battery terminal.

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds - chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

17

WARNING

Backfire, fire or engine damage could

occur.

• DO NOT stop engine by moving choke control to “Choke”

position

().

WARNING

Storage batteries give off explosive

hydrogen gas during recharging.

Hydrogen gas stays near battery for a

long time after battery has been charged.

Slightest spark will ignite hydrogen and cause explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is extremely

caustic.

Contact with battery fluid will cause severe chemical burns.

• DO NOT allow any open flame, spark, heat, or lit cigarette

during and for several minutes after charging a battery.

• Wear protective goggles, rubber apron, and rubber gloves.

7. Start engine. Let engine run while battery recharges.

8. When battery has charged, shut down engine

NOTE: Use an automotive hydrometer to test battery state of

charge and condition. Follow the hydrometer manufacturer’s

instructions carefully. Generally, a battery is considered to be

at 100% state of charge when specific gravity of its fluid (as

measured by hydrometer) is 1.260 or higher.

Cold Weather Operation

Under certain weather conditions (temperatures below 40°F

[4°C] combined with high humidity), your generator may

experience icing of the carburetor and/or the crankcase

breather system. To reduce this problem, you need to

perform the following:

1. Make sure generator has clean, fresh fuel.

2. Open fuel valve (turn valve to open position).

3. Use SAE 5W-30 oil.

4. Check oil level daily or after every eight (8) hours of

operation.

5. Maintain generator following Maintenance Schedule in

Maintenance section.

6. Shelter unit from elements.

Creating a Temporary Cold Weather Shelter

1. For temporary shelter, the original shipping carton can

be used.

2. Cut off top carton flaps and one long side of carton to

expose muffler side of unit. If required, tape up other

sides of carton to fit over generator as shown.

NOTE: If required, remove wheel kit to fit carton over

generator as shown.

3. Cut appropriate slots to access receptacles of unit.

4. Face exposed end away from wind and elements.

5. Locate generator as described in the section Generator

Location. Keep exhaust gas from entering a confined

area through windows, doors, ventilation intakes or

other openings.

6. Start generator as described in the section Starting the

Engine, then place carton over generator. Keep at least

5 ft. (1.5 m) clearance on all sides of generator

including overhead with shelter in place.

7. Remove shelter when temperatures are above 40°F

[4°C].

8. Turn engine OFF and let cool two (2) minutes before

refueling. Let any spilled fuel evaporate before starting

engine.

Building a Cold Weather Shelter

1. Using non combustible material with a fire rating of at

least one hour, build a shelter that will enclose three

sides and the top of the generator. Make sure muffler

side of generator is exposed.

NOTE: Contact your local building material supplier for non

combustible materials with a fire rating of at least one hour.

IMPORTANT: Be sure shelter can easily be repositioned for

change in wind direction.

2. DO NOT enclose generator any more than shown.

Shelter should hold enough heat created by the

generator to prevent icing problem.

NOTE: If a wheel kit is installed on the generator, enlarge

shelter accordingly.

3. Follow steps 3 through 8 as described previously in

Creating a Temporary Cold Weather Shelter.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

generator including overhead.

• Remove shelter when temperatures are above 40°F [4°C].

18 BRIGGSandSTRATTON.COM

Wind

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate generator ONLY outdoors.

• Install a battery operated carbon monoxide alarm near the

bedrooms.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

(even if windows and doors are open), including the generator

compartment of a recreational vehicle (RV).

Don’t Overload Generator

Capacity

You must make sure your generator can supply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items. This is

the amount of power your generator must produce to

keep your items running. See the table on the right.

3. Estimate how many surge (starting) watts you will need.

Surge wattage is the short burst of power needed to

start electric motor-driven tools or appliances such as a

circular saw or refrigerator. Because not all motors start

at the same time, total surge watts can be estimated by

adding only the item(s) with the highest additional surge

watts to the total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3275

Highest Additional Surge Watts = 2350

Total Generator Output Required = 5625

Power Management

To prolong the life of your generator and attached devices, it

is important to take care when adding electrical loads to your

generator. There should be nothing connected to the

generator outlets before starting its engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity, as

described above.

* Wattages listed are approximate only. Check tool or

appliance for actual wattage.

19

Tool or Appliance

Running (Rated)

Watts

Additional Starting

(Surge) Watts

Water Well Pump 1200 2100

Refrigerator 700 2200

Furnace Fan 800 2350

Television 500 —

Light (75 Watts) 75 —

3275 Total

Running Watts

2350 Highest

Starting Watts

Wattage Reference Guide

Tool or Appliance

Running*

(Rated)

Watts

Additional

Starting

(Surge)

Watts

Essentials

Light Bulb - 75 watt 75 —

Furnace Fan Blower - 1/2 HP 800 2350

Sump Pump - 1/3 HP 800 1300

Refrigerator/Freezer 700 2200

Water Well Pump - 1/2 HP 1000 2100

Heating/Cooling

Window AC - 10,000 BTU 1200 3600

Humidifier - 13 Gal 175 —

Central AC - 24,000 BTU 3800 11400

Kitchen

Microwave Oven - 1000 Watt 1000 —

Coffee Maker 1000 —

Electric Stove - 8” Element 2100 —

Toaster 850 —

Family Room

DVD/CD Player 100 —

VCR 100 —

Stereo Receiver 450 —

Color Television - 27 in 500 —

Personal Computer w/17 in

monitor

800 —

Other

Security System 500 —

AM/FM Clock Radio 100 —

Garage Door Opener - 1/2 HP 875 2350

Electric Water Heater 4700 11700

DIY/Job Site

Quartz Halogen Work Light 1000 —

Airless Sprayer - 1/3 HP 600 1200

Reciprocating Saw 960 —

Electric Drill - 1/2 HP, 5.4 Amps 600 900

Circular Saw - 7-1/4 in 1400 2300

Miter Saw - 10 in 1800 1800

Table Planer - 6 in 1800 1800

Table Saw/Radial Arm Saw - 10 in 2000 2000

Air Compressor - 1 HP 1600 4500

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs

first. More frequent service is required when operating in

adverse conditions noted below.

1

Service more often under dirty or dusty conditions.

2

Change engine oil every 50 hours if you are using your generator under heavy

load, or in extremely hot weather.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the generator. See any authorized dealer for

service.

The generator’s warranty does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must maintain the

generator as instructed in this manual.

Some adjustments will need to be made periodically to

properly maintain your generator.

All service and adjustments should be made at least once

each season. Follow the requirements in the Maintenance

Schedule chart above.

NOTE: Once a year you should clean or replace the spark

plug and replace the air filter. New spark plugs and clean air

filter assure proper fuel-air mixture and help your engine run

better and last longer.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual.

However, to obtain ”no charge” emissions control service,

the work must be performed by a factory authorized dealer.

See the Emissions Warranty.

Generator Maintenance

Generator maintenance consists of keeping the unit clean

and dry. Operate and store the unit in a clean dry

environment where it will not be exposed to excessive dust,

dirt, moisture, or any corrosive vapors. Cooling air slots in

the generator must not become clogged with snow, leaves,

or any other foreign material.

NOTE: DO NOT use water or other liquids to clean generator.

Liquids can enter engine fuel system, causing poor

performance and/or failure to occur. In addition, if liquid

enters generator through cooling air slots, some of the liquid

will be retained in voids and cracks of the rotor and stator

winding insulation. Liquid and dirt buildup on the generator

internal windings will eventually decrease the insulation

resistance of these windings.

Cleaning

Daily or before use, look around and underneath the

generator for signs of oil or fuel leaks. Clean accumulated

debris from inside and outside the generator. Keep the

linkage, spring and other engine controls clean. Keep the

area around and behind the muffler free from any

combustible debris. Inspect cooling air slots and openings

on generator. These openings must be kept clean and

unobstructed.

Engine parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris:

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE

Improper treatment of generator can damage it

and shorten its life.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a vacuum cleaner to pick up loose dirt and debris.

Battery Maintenance

Other than float charging, described elsewhere, no

maintenance is required for the starting battery. Keep the

battery and terminals clean and dry.

IMPORTANT: Battery charging should be performed in a dry

location, such as inside a garage.

20 BRIGGSandSTRATTON.COM

First 8 Hours

• Change engine oil

Every 8 Hours or Daily

• Clean debris

• Check engine oil level

Every 25 Hours or Yearly

• Service engine air cleaner pre-filter

1

Every 50 Hours or Yearly

• Inspect muffler and spark arrester

Every 100 Hours or Yearly

• Service engine air cleaner paper filter

1

• Service fuel filter

• Service spark plugs

• Change engine oil and filter

2

• Clean cooling system

1

Every 250 Hours or Yearly

• Check valve clearance

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds - chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

La page charge ...

Simplicity 030338-00 Manuel utilisateur

Simplicity 030338-00 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents