Unitronics IO-ATC8 Manuel utilisateur

Marque: Unitronics

Modèle: IO-ATC8

Taper: Manuel utilisateur

Vous trouverez ci-dessous de brèves informations pour Module d'extension E/S IO-ATC8. Ce module d'extension offre 8 entrées qui peuvent être configurées comme entrées analogiques ou thermocouples via le câblage, les cavaliers et les paramètres logiciels. Il se connecte aux contrôleurs OPLC Unitronics par un adaptateur. Le module peut être monté sur un rail DIN ou vissé sur une plaque de montage. Il dispose également d'indicateurs d'état et de points de connexion pour les entrées.

Unitronics Industrial Automation

IO-ATC8 User Guide

I/O Expansion Module 8 Analog/Thermocouple Inputs

The IO-ATC8 is an I/O Expansion Module

that can be used in conjunction with

specific Unitronics OPLC controllers.

The module offers 8 inputs that may be

set as either analog or thermocouple

inputs via wiring, jumper and software

settings.

The interface between the module and the

OPLC is provided by an adapter.

The module may either be snap-mounted

on a DIN rail, or screw-mounted onto a

mounting plate.

1 5

Component identification

Module-to-module connector

Communication status indicator

Input connection points, I4 to I7

Input status indicators

Module-to-module connector port

Input connection points, I0 to I3

◼ Before using this product, it is the responsibility of the user to read and understand this document and

any accompanying documentation.

◼ All examples and diagrams shown herein are intended to aid understanding, and do not guarantee

operation. Unitronics accepts no responsibility for actual use of this product based on these examples.

◼ Please dispose of this product in accordance with local and national standards and regulations.

◼ Only qualified service personnel should open this device or carry out repairs.

User safety and equipment protection guidelines

This document is intended to aid trained and competent personnel in the installation of this equipment as

defined by the European directives for machinery, low voltage, and EMC. Only a technician or engineer trained

in the local and national electrical standards should perform tasks associated with the device’s electrical wiring.

Symbols are used to highlight

information relating to the user’s

personal safety and equipment

protection throughout this document.

When these symbols appear, the

associated information must be read

carefully and understood fully.

Symbol

Meaning

Description

Danger

The identified danger causes physical

and property damage.

Warning

The identified danger can cause

physical and property damage.

Caution

Use caution.

◼ Failure to comply with appropriate safety guidelines can result in severe personal injury or

property damage. Always exercise proper caution when working with electrical equipment.

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

◼ Check the user program before running it.

◼ Do not attempt to use this device with parameters that exceed permissible levels.

◼ To avoid damaging the system, do not connect / disconnect the device when the power is on.

Environmental Considerations

◼ Do not install in areas with: excessive or conductive dust, corrosive or flammable gas,

moisture or rain, excessive heat, regular impact shocks or excessive vibration.

◼ Leave a minimum of 10mm space for ventilation between the top and bottom edges of the

device and the enclosure walls.

◼ Do not place in water or let water leak onto the unit.

◼ Do not allow debris to fall inside the unit during installation.

Mounting the Module

DIN-rail mounting

Snap the device onto the DIN rail as shown below; the module will be squarely situated on the DIN rail.

60mm

(2.362")

3.5mm

(0.137")

14mm

(0.55")

80mm

(3.15")

93mm

(3.66")

44.5mm

(1.75")

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

Screw-Mounting

The figure below is not drawn to scale. It may be used as a guide for screw-mounting the module.

Mounting screw type: either M3 or NC6-32.

4mm

5.8mm

(0.228")

85mm

(3.346")

80mm

(3.15")

68.4mm

(2.693")

93mm

(3.66")

4mm (x2)

(0.16")

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

Connecting Expansion Modules

An adapter provides the interface between the OPLC and an expansion module. To connect the I/O module to

the adapter or to another module:

1. Push the module-to-module connector into the port located on the right side of the device.

Note that there is a protective cap provided with the adapter. This cap covers the port of the final

I/O module in the system.

◼ To avoid damaging the system, do not connect or disconnect the device when the

power is on.

1 2

Component identification

Module-to-module

connector

Protective cap

Wiring

◼ Do not touch live wires.

◼ Unused pins should not be connected. Ignoring this directive may damage the device.

◼ Do not connect the ‘Neutral or ‘Line’ signal of the 110/220VAC to the device’s COM pins.

◼ Double-check all wiring before turning on the power supply.

Wiring Procedures

Use crimp terminals for wiring; use 26-12 AWG wire (0.13 mm 2–3.31 mm2) for all wiring purposes.

1. Strip the wire to a length of 7±0.5mm (0.250–0.300 inches).

2. Unscrew the terminal to its widest position before inserting a wire.

3. Insert the wire completely into the terminal to ensure that a proper connection can be made.

4. Tighten enough to keep the wire from pulling free.

◼ To avoid damaging the wire, do not exceed a maximum torque of 0.5 N·m (5 kgf·m).

◼ Do not use tin, solder, or any other substance on stripped wire that might cause the wire strand to break.

◼ Install at maximum distance from high-voltage cables and power equipment.

I/O Wiring—General

◼ Input or output cables should not be run through the same multi-core cable or share the same wire.

◼ Allow for voltage drop and noise interference with input lines used over an extended distance. Use wire

that is properly sized for the load.

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

Analog Inputs

◼ Shields should be connected at the signal source.

◼ Inputs may be set as either thermocouple, current, or voltage. To set an input:

- Use the appropriate wiring as shown below.

- Open the device and set the jumpers according to the instructions beginning on page 6.

◼ The adapter and the COM signals of the analog inputs must be connected to the same 0V signal.

◼ The COM signals of each channel are internally shorted.

◼ When set to current/voltage, each 2 inputs share a common COM signal.

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

Opening the Device

◼ Before opening the device, touch a grounded object to discharge any electrostatic

charge.

◼ Avoid touching the PCB board directly.

◼ Turn power off and disconnect all leads before opening the device.

In order to change the jumper settings of a specific input, first open the device by prying off its back, using the

blade of a flat-bladed screwdriver. The insertion points for the screwdriver are located on both sides of the

module.

1. Open the first side of the device by inserting the blade between the 2 plastic moldings as shown below, then

gently pushing up.

2. Taking care not to damage the cable, open the other side of the device by inserting the blade where shown

below, then gently pushing up.

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

3. Gently remove the top of the

device as shown.

4. The jumpers are shown at right.

Change the jumper settings as

required, in accordance with the

tables shown on the next page.

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

Jumper Settings

The tables below show how to set a specific jumper to change the functionality of a specific input.

To open the device and access the jumpers, refer to the instructions beginning on page 6.

Caution

◼ Incompatible jumper settings and wiring may severely damage the device.

Jumper #

Thermocouple*

Voltage

Current

Input 0

Input 1

Input 2

Input 3

Input 4

Input 5

Input 6

Input 7

* Default factory setting.

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

IO-ATC8 Technical Specifications

Max. current consumption

40mA maximum from the adapter’s 5VDC

Typical power consumption

0.2W@5VDC

Status indicator

(RUN)

Green LED:

—Lit when a communication link is established between module and OPLC.

—Blinks when the communication link fails.

Thermocouple Inputs

Number of inputs

8. See Note 1.

Input type

Thermocouple, differential inputs. See Note 2.

Input range

As shown in table below.

Isolation

None

Conversion method

Voltage to frequency

Resolution

0.1ºC (0.1ºF) See Note 3.

Conversion time

100mSec minimum, according to the filter type selected in software settings

Input impedance

>10MΩ

Cold junction compensation

Local, automatic

Cold junction compensation

error

±1.5ºC (±2.7ºF) maximum

Absolute maximum rating

±0.6VDC

Linearity error

0.04% maximum of full scale

Error limit

0.4% of input value

Warm-up time

Typically ½ hour, ±1ºC (±1.8ºF) repeatability

Status indicators

(OUT OF RANGE)

Red LEDs—Lit when the corresponding input measures an analog value in

excess of the input range. See Note 4.

Thermocouple input ranges

Type

Temperature range

Wire color

ANSI (USA)

BS 1843 (UK)

-5 to 56mV

200 to 1820°C

+ Grey

+ None

(300 to 3276°F)

- Red

- Blue

-200 to 750°C

+ Violet

+ Brown

(-328 to 1382°F)

- Red

- Blue

-200 to 760°C

+ White

+ Yellow

(-328 to 1400°F)

- Red

- Blue

-200 to 1250°C

+ Yellow

+ Brown

(-328 to 2282°F)

- Red

- Blue

-200 to 1300°C

+ Orange

(-328 to 2372°F)

- Red

- Blue

0 to 1768°C

+ Black

+ White

(32 to 3214°F)

- Red

- Blue

0 to 1768°C

+ Black

+ White

(32 to 3214°F)

- Red

- Blue

-200 to 400°C

+ Blue

+ White

(-328 to 752°F)

- Red

- Blue

Analog Inputs

Number of inputs

8 (single-ended) See Note 1.

Input range

0-10V, 0-20mA, 4-20mA. See Note 1.

Input type

Either Normal or Fast mode, according to the filter type selected in software

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

settings

Conversion method

Voltage to frequency

Normal mode

Resolution at 0-10V,

0-20mA

14-bit (16384 units)

Resolution at 4-20mA

3277 to16383 (13107 units)

Conversion time

100mSec minimum per input

Fast mode

Resolution at 0-10V,

0-20mA

12-bit (4096 units)

Resolution at 4-20mA

819 to 4095 (3277 units)

Conversion time

25mSec minimum per input

Input impedance

>400KΩ—voltage

500Ω—current

Isolation

None

Absolute maximum rating

±15V—voltage

±30mA—current

Linearity error

0.04% max of full scale

Error limits

0.4% of input value

Status indicators

(OUT OF RANGE)

Red LEDs—Lit when the corresponding input is receiving current or voltage in

excess of the input range. See Note 5.

Environmental

IP20/NEMA1

Operating temperature

0 to 50C (32 to 122° F)

Storage temperature

-20 to 60C (-4 to 140° F)

Relative Humidity (RH)

5% to 95% (non-condensing)

Dimensions (WxHxD)

80mm x 93mm x 60mm (3.15 x 3.66 x 2.362”)

Weight

150g (5.3 oz)

Mounting

Either onto a 35mm DIN-rail or screw- mounted.

Notes:

1. Each input may be set as either thermocouple, voltage (0-10V), or current (0-20mA, 4-20mA)

via wiring, jumper and software settings.

2. The device can also measure voltage within the range of -5 to 56mV, at a resolution of 0.01mV.

The device can also measure raw value frequency at a resolution of 14-bits(16384).

3. The input analog value represents the measured value as shown in the following examples:

- Thermocouple: a value of 262 is represented as 26.2ºC.

- mV: value of 262 is represented as 2.62mV.

4. The value of a thermocouple may also indicate when the sensor is not connected to the input, or

when the analog value exceeds the permissible range. If such is the case, the value will be 32767.

5. The voltage or current value of analog inputs can also indicate faults, as shown in the table below.

Value: 12-bit

(Fast mode)

Value: 14-bit

(Normal mode)

Input Value

Deviates:

-1

Slightly below the input range.

4096

16384

Slightly above the input range.

32767

Greatly above or below the input range.

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

Addressing I/Os on Expansion Modules

Inputs and outputs located on I/O expansion modules that are connected to an OPLC are assigned

addresses that comprise a letter and a number. The letter indicates whether the I/O is an input (I) or an

output (O). The number indicates the I/O’s location in the system. This number relates to both the position

of the expansion module in the system, and to the position of the I/O on that module.

Expansion modules are numbered from 0-7 as shown in the figure below.

0 1 2 3 4 5 6 7 Expansion module

identification number

Adapter

The formula below is used to assign addresses for I/O modules used in conjunction with the OPLC.

X is the number representing a specific module’s location (0-7). Y is the number of the input or output on that

specific module (0-15).

The number that represents the I/O’s location is equal to:

32 + x • 16 + y

Examples

◼ Input #3, located on expansion module #2 in the system, will be addressed as I 67,

67 = 32 + 2 • 16 + 3

◼ Output #4, located on expansion module #3 in the system, will be addressed as O 84,

84 = 32 + 3 • 16 + 4.

EX90-DI8-RO8 is a stand-alone I/O module. Even if it is the only module in the configuration, the EX90-DI8-

RO8 is always assigned the number 7.

Its I/Os are addressed accordingly.

Example

◼ Input #5, located on an EX90-DI8-RO8 connected to an OPLC will be addressed

as I 149, 149 = 32 + 7 • 16 + 5

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

UL Compliance

The products listed above may be used with compatible Unitronics PLCs.

Detailed Installation Guides containing the I/O wiring diagrams for these models, technical specifications, and

additional documentation are located in the Technical Library in the Unitronics website:

https://unitronicsplc.com/support-technical-library/

The following section is relevant to Unitronics’ products that are listed with the UL.

The following models: IO-AI4-AO2, IO-AO6X, IO-ATC8, IO-DI16, IO-DI16-L, IO-DI8-RO4,

IO-DI8-RO4-L, IO-DI8-TO8, IO-DI8-TO8-L, IO-RO16, IO-RO16-L, IO-RO8, IO-RO8L, IO-TO16,

EX-A2X are UL listed for Hazardous Locations.

The following models: EX-D16A3-RO8, EX-D16A3-RO8L, EX-D16A3-TO16, EX-D16A3-TO16L,

IO-AI1X-AO3X, IO-AI4-AO2, IO-AI4-AO2-B, IO-AI8, IO-AI8Y, IO-AO6X, IO-ATC8, IO-D16A3-RO16,

IO-D16A3-RO16L, IO-D16A3-TO16, IO-D16A3-TO16L, IO-DI16, IO-DI16-L, IO-DI8-RO4,

IO-DI8-RO4-L, IO-DI8-RO8, IO-DI8-RO8-L, IO-DI8-TO8, IO-DI8-TO8-L, IO-DI8ACH, IO-LC1, IO-LC3,

IO-PT4, IO-PT400, IO-PT4K, IO-RO16, IO-RO16-L, IO-RO8, IO-RO8L, IO-TO16, EX-A2X, EX-RC1 are

UL listed for Ordinary Location.

UL Ratings, Programmable Controllers for Use in Hazardous Locations,

Class I, Division 2, Groups A, B, C and D

These Release Notes relate to all Unitronics products that bear the UL symbols used to mark products that

have been approved for use in hazardous locations, Class I, Division 2, Groups A, B, C and D.

Caution

◼This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D, or Non-hazardous

locations only.

◼ Input and output wiring must be in accordance with Class I, Division 2 wiring methods and in

accordance with the authority having jurisdiction.

◼ WARNING—Explosion Hazard—substitution of components may impair suitability for Class I,

Division 2.

◼ WARNING – EXPLOSION HAZARD – Do not connect or disconnect equipment unless power has

been switched off or the area is known to be non-hazardous.

◼ WARNING – Exposure to some chemicals may degrade the sealing properties of material used in

Relays.

◼ This equipment must be installed using wiring methods as required for Class I, Division 2 as per

the NEC and/or CEC.

Relay Output Resistance Ratings

The products listed below contain relay outputs:

Input/Output expansion modules, Models: IO-DI8-RO4, IO-DI8-RO4-L, IO-RO8, IO-RO8L

◼ When these specific products are used in hazardous locations, they are rated at 3A res, when these specific

products are used in non-hazardous environmental conditions, they are rated at 5A res, as given in the

product’s specifications.

UG_IO-ATC8 I/O Expansion Module

Unitronics Industrial Automation

Certification UL des automates programmables, pour une utilisation en environnement à

risques, Class I, Division 2, Groups A, B, C et D.

Cette note fait référence à tous les produits Unitronics portant le symbole UL - produits qui ont été certifiés

pour une utilisation dans des endroits dangereux, Classe I, Division 2, Groupes A, B, C et D.

Attention

◼ Cet équipement est adapté pour une utilisation en Classe I, Division 2, Groupes A, B, C et

D, ou dans Non-dangereux endroits seulement.

◼ Le câblage des entrées/sorties doit être en accord avec les méthodes

de câblage selon la Classe I, Division 2 et en accord avec l’autorité compétente.

◼ AVERTISSEMENT: Risque d’Explosion – Le remplacement de certains composants rend caduque

la certification du produit selon la Classe I, Division 2.

◼ AVERTISSEMENT - DANGER D'EXPLOSION - Ne connecter pas ou ne débranche pas

l'équipement sans avoir préalablement coupé l'alimentation électrique ou la zone est reconnue pour

être non dangereuse.

◼ AVERTISSEMENT - L'exposition à certains produits chimiques peut dégrader les propriétés des

matériaux utilisés pour l'étanchéité dans les relais.

◼ Cet équipement doit être installé utilisant des méthodes de câblage suivant la norme Class I,

Division 2 NEC et /ou CEC.

Certification de la résistance des sorties relais

Les produits énumérés ci-dessous contiennent des sorties relais:

◼ Modules d’Extensions d'E/S, modèles: IO-DI8-RO4, IO-DI8-RO4-L, IO-RO8, IO-RO8L.

◼ Lorsque ces produits spécifiques sont utilisés dans des endroits dangereux, ils supportent

un courant de 3A charge résistive, lorsque ces produits spécifiques sont utilisés dans un environnement non

dangereux, ils sont évalués à 5A res, comme indiqué dans les specifications du produit Plages de

températures.

The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole discretion, and without notice, to

discontinue or change the features, designs, materials and other specifications of its products, and to either permanently or temporarily withdraw any of the forgoing from the market.

All information in this document is provided "as is" without warranty of any kind, either expressed or implied, including but not limited to any implied warranties of merchantability, fitness for a

particular purpose, or non-infringement. Unitronics assumes no responsibility for errors or omissions in the information presented in this document. In no event shall Unitronics be liable for any

special, incidental, indirect or consequential damages of any kind, or any damages whatsoever arising out of or in connection with the use or performance of this information.

The tradenames, trademarks, logos and service marks presented in this document, including their design, are the property of Unitronics (1989) (R"G) Ltd. or other third parties and you are not

permitted to use them without the prior written consent of Unitronics or such third party as may own them

UG_IO-ATC8.pdf 11/22