Haier QFT15 Electric Dryer Le manuel du propriétaire

Catégorie
Sèche-linge
Taper
Le manuel du propriétaire
Dryers
Sécheuses
Secadoras
49-3000193 Rev 1 01-22 GEA
QFT15 Series/Séries/Serie
Owner's Manual &
Installation Instructions
Manuel d'utilisation et
Instruction d'installation
Manual del propietario y
Instrucciones de instalación
249-3000193 Rev 1
ENGLISH
RECORD KEEPING
Thank you for purchasing this Haier Appliances product. This
Owner's Manual will help you get the best performance from
your new dryer.
For future reference, record the model and serial number
located on a label on the front of the dryer behind the door.
Staple your proof of purchase to this manual to aid in
obtaining warranty service if needed.
____________________________________________________
Model number
____________________________________________________
Serial number
____________________________________________________
Date of purchase
TABLE OF CONTENTS
SAFETY INFORMATION ............................................................................................3
USING THE DRYER ................................................................................................4
Getting Started ........................................................................................................ 4
Loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Features ............................................................................................................... 8
CARE AND CLEANING .............................................................................................9
INSTALLATION INSTRUCTIONS ...................................................................................12
Stacking (Optional) ...................................................................................................... 20
Reversing The Door Swing (Optional) .................................................................................. 22
TROUBLESHOOTING TIPS ........................................................................................24
LIMITED WARRANTY .............................................................................................27
CONSUMER SUPPORT ........................................................................................... 28
49-3000193 Rev 1 3
ENGLISH
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE
To reduce the risk of fire, explosion, electric shock, or injury to persons when using your appliance, follow
basic precautions, including the following:
Read all instructions before using the appliance.
DO NOT dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning
solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.
DO NOT place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a
chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to contaminated loads, the final part of
the tumble dryer cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the end of the drying
cycle unless all items are quickly removed and spread out so that the heat is dissipated.
DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this appliance is
used near children.
Before the appliance is removed from service or discarded, remove the door to the drying compartment.
DO NOT reach into the appliance if the drum is moving.
DO NOT install or store this appliance where it will be exposed to the weather.
DO NOT tamper with controls.
DO NOT climb or stand on this unit.
DO NOT repair or replace any part of this appliance or attempt any servicing unless specifically recommended in the
user-maintenance instructions or in published user-repair instructions that you understand and have the skills to carry out.
Follow all fabric care instructions and warnings to prevent melting of garments or damage to the appliance.
DO NOT use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric
softener or product.
DO NOT dry articles containing foam rubber or similarly textured rubber-like materials.
Clean lint screen and clean and empty the condenser before or after each load.
DO NOT operate the dryer without the lint filter and condenser in place.
DO NOT store combustible materials, gasoline or other flammable liquids near the dryer. Keep area around the air
intake
vent on the front of the dryer and adjacent surrounding areas free from the accumulation of lint, dust and dirt.
The interior of the appliance should be cleaned periodically by qualified service personnel.
Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power or Start/Pause button DOES NOT
disconnect power.
DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts,
including a damaged cord or plug.
DO NOT spray any type of aerosol into, on or near dryer at any time. DO NOT use any type of spray cleaner when cleaning dryer
interior. Hazardous fumes or electrical shock could occur
.
See “ELECTRICAL CONNECTION” located in the Installation Instructions for grounding instructions.
WARNING
449-3000193 Rev 1
ENGLISH
USING THE DRYER
Throughout this manual, features and appearance may vary from your model.
If the screen is dark, press
and hold the power button
for 2 seconds to “wake up
the display.
Step 2* Step 3* Step 4*
Step 1*
Select a dry cycle. (Defaults are set for
each dry cycle. These default settings
can be changed. See control settings
for more information.)
Press and hold
the start button
for 1 second.
Loosely add items.
Close door.
NOTE: Dryer will not start
with door open.
To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY
INFORMATION before operating this appliance.
WARNING
*Instructions can also be found by touching the document ( ) icon, on the cycle selection screen, in the top right corner.
Clean Filter
Empty Tank
Controls
CONDENSER DRYERCONDENSER DRYER
AB
I
Clean Filter
Empty Tank
C D E F
G
H
J
49-3000193 Rev 1 5
ENGLISH
USING THE DRYER
Power
Press and hold for 2 seconds to “wake up” the display. If the display is active, press and hold for 2 seconds to turn the
dryer off. NOTE: Pressing the power does not disconnect the appliance from the power supply.
Dry Cycles
The dry cycle controls the cycle time for the drying process. The chart below will help you match the dry setting with
the loads.
B
A
Mixed Loads For loads consisting of cottons and poly blends.
Cottons For cottons and most linens. NOTE: ENERGY STAR® models are tested on Cottons with default
settings.
Heavy duty For large coats, bed spreads, mattress covers, sleeping bags, blankets, comforters, jackets, small rugs,
and similar large and bulky items.
Towels Use for towels OR sheets. It is not recommended to mix towels and sheets in the same load.
Casuals For wrinkle-free, permanent press and delicate items, and knits.
Active Wear Clothing worn for active sports exercise and some casual wear. Fabrics include new technology
finishes and stretch fibers such as Spandex. Also for clothing labeled Easy Care or Perma Press: For
wrinkle-free and permanent press items.
Sanitize Reduces certain types of bacteria by 99.6%, including: Staphylococcus aureus and Pseudomonas
aeruginosa. The antibacterial process occurs when high heat is used during a portion of this drying
cycle.
Quick Dry For small loads that are needed in a hurry, such as sports or school uniforms. Can also be used if the
previous cycle left some items damp, such as collars or waistbands.
Delicates For lingerie and special-care fabrics.
Dewrinkle For removing wrinkles from items that are dry or slightly damp. This cycle is not recommended for
delicate fabrics.
Warm Up Provides 25 minutes of warming time to warm up clothes.
Air Fluff Provides 30 minutes of tumbling time without heat.
Rack Dry For drying delicate items without tumbling, use drying rack accessory. Place items flat on the drying
rack such as wool sweaters and delicate fabrics. Dry with low heat.
Baby Care For drying childrens clothes and other small items.
Jeans For drying denim and heavy canvas textiles.
Timed Dry Use to set your own dry time. Time Dry is also recommended for small loads. To use:
1. Select Timed Dry cycle.
2. Select the drying Time in 10-minute increments up to 2 hours and 30 minutes.
2. Select the dry Temp.
3. Close the door.
4. Press and hold Start.
Display and Status Lights
The display shows the approximate time remaining until the end of the cycle.
In addition, this display will show the dryer status:
Status
Dry Damp Cool
Controls lock feature.
Clean Filter Time to clean the filter. See the Care and Cleaning section.
Damp Alert When Damp Alert option is selected and clothes have dried to a damp dryness level, indicator will appear and dryer will beep.
Estimated Time
Remaining Display shows the estimated time remaining until set cycle is completed.
Ext Tumble Indicates the Extended Tumble feature is set.
Delay Indicates Delay Dry set time is selected.
Indicates the My Cycle feature is set.
eDry Shows eDry setting selected.
Temp Shows High, Medium, Low or No Heat temperature setting selected.
Level Shows Extra Dry, Dry or Damp dryness setting selected.
Delay Dry Indicates Delay Dry is set time is selected.
649-3000193 Rev 1
ENGLISH
USING THE DRYER
Level
The sensor continuously monitors the amount of moisture in the load. When the moisture in your
clothes reaches your selected dry level, the dryer will stop.
NOTE: Sensor dry Level can be used with all cycles except Timed Dry, Air Fluff, Rack Dry, Warm Up
and Dewrinkle.
Extra Dry Use for heavy-duty fabrics or items that should be very dry, such as towels.
Dry Use for normal dryness level suitable for most loads. This is the preferred cycle for energy saving.
Less Dry Use for lighter fabric (ideal for ironing).
Damp For leaving items partially damp.
Delay Dry
Use to delay the start of your dryer.
1. Choose your dry cycle and any options.
2. In the Delay Dry section. You can change the delay time in 1 hour increments up to 24 hours.
3. Press and hold the start ( ) icon for 1 second to start the countdown. The selected delay time will not be
shown on the screen. Only the estimated cycle time will be visible. Once the delayed time period has been
completed, the selected dry cycle will start.
NOTE: If the door is opened while the dryer is in Delay Dry, the countdown time will not restart unless
the door is closed and Start icon has been pressed again.
D
E
Temp (Temperature)
You can change the temperature of your dry cycle.
High For regular to heavy cottons.
Medium For synthetics, blends and items labeled Permanent Press.
Low For delicates, synthetics and items labeled Tumble Dry Low.
No Heat This option may only be used with Air Fluff and Timed Dry, in which items are tumbled
without heat.
C
FOptions
Damp Alert
This option causes the dryer to beep when clothes have dried to a damp level and the Damp Alert indicator
to
appear on the screen. Remove items that you wish to hang dry. This feature will only beep when the Damp Alert
option is selected. The dryer will continue to dry after the Damp Alert indicator is populated on the screen and
dryer beeps. Removing clothes and hanging them when they are damp can reduce the need to iron some items.
Extended Tumble
Minimizes wrinkles by adding approximately 2 hours of no-heat tumbling after clothes are dry.
The estimated time remaining display will show “END.
The extended tumble time does not get added to the cycle time on the display.
Detangle
Activates alternating forward and reverse tumbling to reduce tangling, dry more evenly, and improve
drying times. Typical loads such as bed and bath mixed loads, where sheets, towels and pillow cases
are laundered together, benefit from this capability. When the dryer reverses direction, there will be a
slight pause and sound change. This is normal.
NOTE: Detangle is selected by default for Towels and Heavy Duty cycles.
eDry
Reduces total energy consumption of specific dryer cycles by adjusting certain heat settings.
NOTE: Cycle times will change when eDry is selected.
ENERGY STAR® models are tested on Cottons cycle with default settings to determine energy use rating of
this dryer. The eDry option will default to on for Cottons. Temperature settings on High and dryness level
setting on Dry are specifically designed for this cycle to reduce energy consumption. For optimal energy
savings, turn eDry on. For optimal drying times, turn eDry off. Energy savings will vary across loads and cycles.
The eDry selection can be used with Mixed Loads, Cottons, Heavy Duty, Towels, Casuals, Active
Wear and Delicates.
Clean Filter
Empty Tank
Clean Filter
Empty Tank
Clean Filter
Empty Tank
Clean Filter
Empty Tank
49-3000193 Rev 1 7
ENGLISH
USING THE DRYER
Start/Pause
Start - Press and hold for 1 second to start or restart a cycle.
Pause - If the dryer is running, press and hold for 1 second to pause the cycle. This function can be
used to add garments during a cycle.
NOTE: If the dryer is paused and the cycle is not restarted within 15 minutes, the current cycle will be
cancelled.
J
My Cycle
Set up your favorite combination of settings for each cycle and save them here for one touch recall.
These custom settings can be set while a cycle is in progress. NOTE: you can store one My Cycle
combination of settings for each cycle.
To store a My Cycle combination of settings:
1. Select your drying cycle.
2. Change Temp and Level settings to fit your needs.
3. Select any drying options you want.
4. Press and hold the pad for 3 seconds to store your selection. A beep will sound and the icon will light up.
To recall your stored My Cycle combination:
Select the cycle and press the icon before drying a load.
To change your stored My Cycle combination:
Repeat steps 1–4.
G
Lock
You can lock the controls to prevent any selections from being made. Or you can lock or unlock the
controls after you have started a cycle.
Children cannot accidentally start the dryer by touching pads with this option selected.
To lock the dryer, press and hold the lock ( ) pad in the top right corner for 3 seconds and a lock
screen will appear.
To unlock the dryer controls, press and hold the unlock ( ) pad for 3 seconds and the lock screen will
disappear.
The control lock icon on the display will light up when it is on.
NOTE: The Power button can still be used when the machine is locked.
B
H
Volume
When the control panel is powered on, the dryer will beep at the end of the cycle and every time you
press a button on the control panel.
Use the Option pad to select either High, Med, Low, or Off.
NOTE: The selected volume is for both end of cycle and pad sounds.
Language
Use the Option pad to select either English, Spanish, or French.
Brightness
To change the brightness of the screen, use the brightness slider to change from darker to brighter.
WiFi Connect + Tub Light
Use the WiFi Connect + Tub Light toggle button to turn this feature on or off. Toggling this feature on will
enable the WiFi Connect function and enable the usage of the tub light when the door is opened & closed.
Follow the directions on the Wifi Connect screen using the information provided to connect with the GEA
Laundry App. Toggling this feature off will disable the Wifi Connect function and disable the tub light.
NOTE: When the dryer to set up with the GEA Laundry App, new software may be available to
install. After approving the installation of the new software through the GEA Laundry App, the
dryer tub light will flash on and off during the software installation. The dryer tub light will stop
flashing and turn off after the software is done installing.
ISettings
Select the gear symbol ( ) in the top right corner to enter the Settings screen.
Clean Filter
Empty Tank
My Cycle
Clean Filter
Empty Tank
Lock
Settings
Clean Filter
Empty Tank
Start
Pause
849-3000193 Rev 1
ENGLISH
LOADING
Fabric Care Labels
Below are fabric care label “symbols” that affect the clothing you will be laundering.
Dry Labels
Always follow fabric manufacturer’s care label when laundering.
As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Try also to sort items
according to size. For example, do not dry a sheet with socks or other small items.
Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce® Fabric
Conditioner Dryer Sheets have been approved for use in this dryer when used in accordance with the manufacturer’s
instructions.
Do not overload. This wastes energy and causes wrinkling.
Keep flammable materials and vapors, such as gasoline,
away from dryer.
DO NOT dry anything that has ever had anything
flammable on it (even after washing).
No washer can completely remove oil.
DO NOT dry anything that has ever had any type of oil on it
(including cooking oils).
Items containing foam, rubber, or plastic must be dried on a
clothesline.
Failure to do so can result in death, explosion, or fire.
Sorting and Loading Hints
Tumble
dry
Dry Normal Permanent Press/
wrinkle resistant Gentle/
delicate Do not tumble dry Do not dry
(used with
do not wash)
Heat
setting
High Medium Low No heat/air
Special
instructions Line dry/
hang to dry Drip dry Dry flat In the shade
- Fire Hazard
WARNING
Drying Rack
A handy drying rack may be used for drying delicate items such as washable sweaters. Place items flat on the drying rack and
block such items as wool sweaters and delicate fabrics. Dry with low heat.
To install the drying rack, extend the drying rack into the dryer drum and rest the front two legs on
the front angled ledge.
NOTES:
The drying rack is designed for use with the Timed Dry cycle. Use with sensor cycles may result
in damp items or extended cycle times.
Do not use this drying rack when there are other clothes in the dryer, that are not placed on the rack.
The drying rack, WE01X26416, is available as an accessory. Visit our website at haierappliances.com/parts or in Canada
visit haiercanada.ca/parts.
49-3000193 Rev 1 9
ENGLISH
CARE AND CLEANING
Exterior
Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some
laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric may then be
washed and dried normally. Damage to your dryer caused by these products is not covered by your warranty.
Stainless Steel
To clean stainless steel surfaces use a damp cloth with a mild, non-abrasive cleaner suitable for stainless steel surfaces.
Remove the cleaner residue and then dry with a clean cloth.
The stainless steel used to make the dryer drum provides the highest reliability available in a Haier Appliances dryer. If the
dryer drum should be scratched or dented during normal use, the drum will not rust or corrode. These surface blemishes will
not affect the function or durability of the drum.
Interior
The interior of the appliance should be cleaned once a year by qualified service personnel.
Lint Filter
Clean the lint filter before each use.
Pull out the lint filter. Moisten your fingers and remove the captured lint. Once clean, slide the
filter back into position. Have a qualified technician vacuum the lint from the dryer once a year.
NEVER OPERATE THE DRYER WITHOUT ITS FILTER IN PLACE.
Drum Lamp
NOTE: The drum lamp is not consumer replaceable on models where there is a flat cover over an LED bulb. If this light should ever
stop working, contact us for service.
For models that have a domed cover over the bulb secured by a screw:
Before replacing the light bulb, be sure to unplug the dryer power cord or disconnect the dryer at the
household distribution panel by removing the fuse or switching off the circuit breaker. Reach above
dryer opening from inside the drum to locate the light.
Remove the screw and the plastic cover to access the bulb. Replace with the appropriate bulb and
then reaffix the cover and screw.
Order replacement bulb WE11X26351 by visiting our website at haierappliances.com/parts or in Canada visit haiercanada.ca/parts.
You may also purchase appliance bulb 7C7 from your local retailer.
When the door is opened, the drum lamp automatically turns on and remains on for 2 minutes. When the door is closed, the drum
lamp will remain on for 30 seconds.
Disconnect power supply before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
WARNING - Shock Hazard
Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing.
Service personnel – DO NOT contact the following parts while the appliance is energized: motor start capacitor, motor
metal holder, and drum wheel shaft.
- Electrical Shock Hazard
WARNING
10 49-3000193 Rev 1
ENGLISH
CARE AND CLEANING
Water Tank
REMOVE THE CONDENSED WATER IN THE TANK AFTER EVERY DRYING CYCLE.
NOTE: If drain hose is installed, emptying the water tank is not required. See the
CONNECTING THE DRAIN HOSE section in the Installation Installations of this manual.
Pull out the water tank.
When removing the water tank from the product, hold it using both hands as it is
heavy and take care not to spill any water inside the tank.
Remove the condensed water inside the water tank.
To avoid over filling, which could lead to water leaking outside the unit, drain water left
in water tank after each cycle. Over filling will cause cycle to stop prematurely until
emptied.
NOTE: When the Empty Tank indicator light is on, the dryer will not operate until the tank is
emptied and the indicator has been cleared. Press the Start button and the indicator light
will turn off and the dryer will resume the cycle.
Condenser
THE CONDENSER SHOULD BE CLEANED ONCE PER MONTH.
Open the condenser compartment cover.
• Unlock both locking tabs.
Remove the condenser box from
the condenser compartment.
Clean the condenser box and inside the condenser compartment completely. Use tap water
to clean between the grooves of the condenser box by allowing tap water to flow through
it. Reach inside the condenser compartment and wipe away all debris. Make sure the rubber
gaskets on the condenser box are free of debris before reinstalling.
NOTES:
Make sure to clean your condenser once per month to prevent degradation of the dryer’s
performance.
When assembling the condenser after cleaning it, make sure the locking tabs are set to the
lock position. Never run the dryer without the condenser installed.
Unlock
Drain hole
is on the
top rear of
the drawer
49-3000193 Rev 1 11
ENGLISH
NOTES
12 49-3000193 Rev 1
ENGLISH
INSTALLATION
DRYER
INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT Save these instructions for
local electrical inspector’s use.
IMPORTANT Observe all governing codes
and ordinances.
Install the clothes dryer according to the
manufacturer’s instructions and local codes.
Note to Installer Be sure to leave these
instructions with the Consumer.
Note to Consumer Keep these instructions for
future reference.
• Clothes dryer installation must be performed by a
qualified installer.
Before the old dryer is removed from service or
discarded, remove the dryer door.
Service information and the wiring diagram are
located in the control console.
Do not allow children on or in the appliance. Close
supervision of children is necessary when the
appliance is used near children.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the Warranty.
Install the dryer where the temperature is above 50°F
for satisfactory operation of the dryer control system.
- Risk of Fire
Clothes dryer installation must be performed by a
qualified installer.
Install the clothes dryer according to these
instructions and local codes.
DO NOT install or store this appliance in any location
where it could be exposed to water or weather.
To reduce the risk of severe injury or death, follow all
installation instructions.
Save these instructions. (Installers: Be sure to leave
these instructions with the customer.)
If you are planning to stack the washer and dryer, order
Stacking Kit number GFA24KITL to be used for this
dryer. Kit sold separately.
WARNING
If you have questions, visit our website at haierappliances.com
or in Canada visit haiercanada.ca.
49-3000193 Rev 1 13
ENGLISH
INSTALLATION INSTRUCTIONS
POWER CORDS
Haier Appliances strongly recommends the use of factory
specified parts. Select the power cord to fit your installation
requirements.
Visit our website at haierappliances.com/parts or in
Canada visit haiercanada.ca/parts.
Part Number Type Length Amperage
WX9X2 3-Prong 4 Feet 30
WX9X3 3-Prong 5 Feet 30
WX9X4 3-Prong 6 Feet 30
WX9X18 4-Prong 4 Feet 30
WX9X19 4-Prong 5 Feet 30
WX9X20 4-Prong 6 Feet 30
*NOTE:
With leveling legs retracted: 33-1/4 (84.5 cm)
With leveling legs fully extended: 33-5/8 (85.4 cm)
Stacked: 66-1/2” (168.9 cm)
Tilt the dryer sideways and remove the foam shipping pads by pulling at the sides and
breaking them away from the dryer legs. Be sure to remove all of the foam pieces around
the legs.
Remove the bag containing the literature.
UNPACKING YOUR DRYER
DRYER
DIMENSIONS
Front
View
23-7/16”
(59.5 cm)
*33-1/4”
(84.5 cm)
Side View
25-1/4” (64.1 cm)
42-13/16” (108.7 cm)
ELECTRICAL CONNECTION
DIMENSIONS
Back
View
30”
(76.2 cm)
20-1/2”
(52.1 cm)
*33-1/4”
(84.5 cm)
14 49-3000193 Rev 1
ENGLISH
INSTALLATION INSTRUCTIONS
MOBILE OR MANUFACTURED HOME
INSTALLATION
Installation MUST conform to the MANUFACTURED
HOME CONSTRUCTION AND SAFETY STANDARD,
TITLE 24, PART 3280 or STANDARD FOR MOBILE
HOMES CAN/CSA-Z240 MH, or, when such
standards are not applicable, with AMERICAN
NATIONAL STANDARD FOR MOBILE HOME, ANSI/
NFPA NO. 501B.
Provide an opening with a free area of at least 25
square inches for introduction of outside air into the
dryer room.
See the sections for electrical connection information.
REQUIREMENTS FOR ALCOVE OR
CLOSET INSTALLATION
Keep flammable materials and vapors, such as gasoline,
away from dryer.
Place dryer at least 18” (46 cm) above the floor for a
garage installation.
Failure to do so can result in death, explosion, or fire.
Minimum clearance between dryer cabinet and
adjacent walls or other surfaces is:
0” either side
1” front and rear
1” top
The rear of the dryer should face a wall.
Consideration must be given to provide adequate
clearance for installation and service.
Closet doors must be louvered or otherwise
ventilated and have at least 60 square inches of open
area. If the closet contains both a washer and a dryer,
doors must contain a minimum of 120 square inches
of open area.
MINIMUM CLEARANCE OTHER THAN
ALCOVE OR CLOSET INSTALLATION
Minimum clearance to combustible surfaces and for air
opening are: 0” both sides, 1” rear and 1” top.
The rear of the dryer should face a wall.
Consideration must be given to provide adequate
clearance for installation and service.
- Explosion Hazard
WARNING
UNDERCOUNTER INSTALLATION
If an undercounter installation is desired:
No special dryer installation kit is required.
If the dryer is installed alone, a minimum of 60
square inches of open area is required. If a washer
and dryer are installed together, a minimum of 120
square inches of open area is required.
BATHROOM OR BEDROOM
INSTALLATION
The installation must conform with local codes or,
in the absence of local codes, with the NATIONAL
ELECTRICAL CODE, ANSI/NFPA NO. 70 (for electric
dryers).
60
square
inches
min.
open
area
Dryer Installed Alone
Countertop and side cabinets
Washer and Dryer Installed Together
Countertop and side cabinets
120
square
inches
min.
open
area
49-3000193 Rev 1 15
ENGLISH
INSTALLATION INSTRUCTIONS
CONNECTING AN ELECTRIC DRYER
Before making the electrical connection, turn off the
circuit breaker(s) or remove the dryer’s circuit fuse(s) at
the electrical box. Be sure the dryer cord is unplugged
from the wall. NEVER LEAVE THE ACCESS COVER OFF
THE TERMINAL BLOCK.
MATERIALS YOU WILL NEED
Safety glasses
Gloves
Dryer power cord kit
(not provided with dryer)
UL rated 120/240V, 30A with
3 or 4 prongs. Identify the
plug type as per the house
receptacle before purchasing
line cord.
Stacking installations may
require a power cord up to 6
feet in length.
TOOLS YOU WILL NEED
Slip-joint pliers
Flat-blade
screwdriver
Phillips
screwdriver
Level
3/4” Strain relief
(UL recognized)
Disconnect power supply before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
WARNING - Shock Hazard
Certain internal parts are intentionally not grounded
and may present a risk of electric shock only during
servicing.
Service personnel – DO NOT contact the following
parts while the appliance is energized: motor start
capacitor, motor metal holder, and drum wheel shaft.
- Electrical Shock Hazard
WARNING
16 49-3000193 Rev 1
ENGLISH
INSTALLATION INSTRUCTIONS
For direct wire connections:
Use 10 gauge copper wire.
Use a UL-listed strain relief.
Disconnect power before making electrical connections.
Connect neutral wire (white or center wire) to center
terminal.
Ground wire (green or bare wire) must be connected to
green ground connector.
Connect remaining two supply wires to remaining two
terminals.
Securely tighten all electrical connections.
Replace the terminal block cover.
Failure to do so can result in death, fire or electrical shock.
GROUNDING INSTRUCTIONS
For a permanently connected dryer: This dryer must
be connected to a grounded metal, permanent wiring
system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to
the equipment-grounding terminal on the appliance.
Improper connection of the equipment-grounding
conductor can result in a risk of
electric shock. Check with a qualified
electrician, or service representative or personnel, if
you are in doubt as to whether the appliance is properly
grounded.
SAVE THESE INSTRUCTIONS
- Fire Hazard
WARNING
WARNING
Use a new UL-listed 240V 30 amp dryer power supply cord
with closed ring terminals or spade terminals with upturned
ends.
Use a UL-listed strain relief.
Disconnect power before making electrical connections.
Connect neutral wire (white or center wire) to center
terminal.
Ground wire (green or bare wire) must be connected to
green ground connector.
Connect remaining two supply wires to remaining two
terminals.
Securely tighten all electrical connections.
Replace the terminal block cover.
Failure to do so can result in death, fire or electrical shock.
For electrical connections using a
power cord:
GROUNDING INSTRUCTIONS
For a grounded, cord-connected dryer: This dryer
must be grounded. In the event of a malfunction or
breakdown, grounding will reduce the risk of electric
shock by providing a path of least resistance for electric
current. This dryer uses a cord having an equipment-
grounding conductor and a grounding plug. The plug
must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all
local codes and ordinances.
Improper connection of the
equipment-grounding conductor can
result in a risk of electric shock. Check with a qualified
electrician, or service representative or personnel, if
you are in doubt as to whether the appliance is properly
grounded. DO NOT modify the plug on the power supply
cord. If it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
SAVE THESE INSTRUCTIONS
- Fire Hazard
WARNING
WARNING
ELECTRICAL CONNECTION
INFORMATION FOR ELECTRIC
DRYERS
ELECTRICAL CONNECTION
INFORMATION FOR ELECTRIC
DRYERS
TO PREVENT ELECTRIC SHOCK, DISCONNECT POWER
BEFORE SERVICING.
This dryer should be connected to an individual branch
circuit with 10 gauge copper wire minimum through a 30
amp fuse or circuit breaker. DO NOT fuse neutral.
Use copper conductors only.
- Electrical Shock Hazard
WARNING
TO PREVENT ELECTRIC SHOCK, DISCONNECT POWER
BEFORE SERVICING.
This dryer should be connected to an individual branch
circuit with 10 gauge copper wire minimum through a 30
amp fuse or circuit breaker. DO NOT fuse neutral.
Use copper conductors only.
- Electrical Shock Hazard
WARNING
49-3000193 Rev 1 17
ENGLISH
INSTALLATION INSTRUCTIONS
CONNECTING DRYER USING 3-WIRE
CONNECTION
CONNECTING DRYER USING 4-WIRE
CONNECTION (MUST BE USED FOR
MOBILE HOME INSTALLATION)
NOTE: Since January 1, 1996, the National Electrical
Code requires that new constructions use a 4-wire
connection to an electric dryer. A 4-wire cord must
also be used where local codes do not permit grounding
through the neutral. 3-wire connection is NOT for use on
new construction.
1. Turn off the circuit breaker(s) (30 amp) or remove the
dryer’s circuit fuse at the electrical box.
2. Be sure the dryer cord is unplugged from the wall
receptacle.
3. Remove the power cord cover located at the upper
back.
4. Remove green ground screw and retain for use in
Step 7. Remove center screw (marked N) in terminal
block. Remove and discard ground strap.
5. Install 3/4 in. UL-recognized strain relief to power
cord entry hole. Bring power cord through strain relief
and bracket.
6. Connect power cord as follows:
A. Connect the 2 hot lines to the outer screws of the
terminal block (marked L1 and L2).
B. Connect the neutral (white) line to the center of the
terminal block (marked N).
7. Attach ground wire of power cord with the green
ground screw (hole above strain relief bracket).
Tighten all terminal block screws (3) securely.
8. Properly secure power cord to strain relief and
bracket.
9. Reinstall the cover.
NEVER LEAVE THE COVER OFF OF THE
TERMINAL BLOCK.
NEVER LEAVE THE COVER OFF OF THE
TERMINAL BLOCK.
3-wire Connection
Not for use in Canada.
DO NOT use for Mobile Home Installations.
NOT for use on new construction.
NOT for use on recreational vehicles.
NOT for use in areas where local codes prohibit
grounding through the neutral conduction.
1. Turn off the circuit breaker(s) (30 amp) or remove the
dryer’s circuit fuse at the electrical box.
2. Be sure the dryer cord is unplugged from the wall
receptacle.
3. Remove the power cord cover located at the upper
back.
4. Install 3/4-in. UL-recognized strain relief to power
cord entry hole. Bring power cord through strain
relief and bracket.
5. Connect power cord as follows:
A. Connect the 2 hot lines to the outer screws of the
terminal block (marked L1 and L2).
B. Connect the neutral (white) line to the center of
the terminal block (marked N).
6. Be sure ground strap is connected to green ground
screw on cabinet rear. Tighten all terminal block
screws (3) securely.
7. Properly secure power cord to strain relief and
bracket.
8. Reinstall the cover.
L1 NL2
Green wire
from power
cord
3/4” Strain
Relief and
Bracket
Cover
4 #10 AWG minimum copper conductors or 120/240V 30A
power supply cord kit marked for use with dryers and provided
with closed loop or spade terminals with upturned ends (not
supplied).
White Wire
Black
or Red
Wire
Black
or
Red
Wire
If required, by local code, install external ground (not
provided) to grounded metal, cold water pipe, or other
established ground determined by a qualified electrician.
L1 NL2
Black or Red Wire
3/4” Strain
Relief and
Bracket
Cover
3 #10 AWG minimum copper conductors or 120/240V 30A
power supply cord kit marked for use with dryers and provided
with closed loop or spade terminals with upturned ends (not
supplied).
Ground
Strap
White Wire
Black
or Red
Wire
18 49-3000193 Rev 1
ENGLISH
CONNECTING THE DRAIN HOSE
DRAINING WATER WITHOUT USING
THE WATER TANK
You can use the dryer without using the water tank by
following the procedures below.
CONNECTING THE DRAIN HOSE
The dryer can pump the condensed water outside of the
DRYER directly with drain hose provide.
The procedures to connect the drain hose are as follows.
1. Disconnect the drain hose A.
2. Connect the drain hose A to
the other hole.
3. Connect accessory hose B
(long drain hose) adjacent to
hose A.
When connecting hose B, take care that the height of
the hose does not exceed 47” (120 cm).
After connecting the drain hose, you can now directly
drain the condensed water to a standpipe or washstand.
CONNECTING THE DRAIN HOSE
(CONT.)
4. Over the edge of a wash basin: The drain hose must
be placed lower than 47” (120 cm) and higher than 30”
(76 cm). To keep the drain hose spout bent, use the
supplied plastic hose guide. Secure the guide to the
wall with a hook or to the tap with a piece of string to
prevent the drain hose from moving.
5. Assemble the drain hose and the hose guide and fix
them with the cable-tie.
Do not push the drain hose in the standpipe any further
than 4” (10 cm). Pushing the drain hose further in the
standpipe can cause leaking.
Back
View
A
A
B
47”
(120 cm)
Max.
Drain Hose Hose Guide
Cable Ties
INSTALLATION INSTRUCTIONS
49-3000193 Rev 1 19
ENGLISH
INSTALLATION INSTRUCTIONS
FINAL SETUP
NOTE: Stacking installations may require a power
cord up to 6 feet in length.
LEVEL THE DRYER
Stand the dryer upright near the final location and adjust
the four leveling legs at the corners to ensure that the
dryer is level from side to side and front to rear.
PLUG DRYER IN
1
2
DRYER START-UP
Press and hold the power button.
NOTE: If the dryer has been exposed to temperatures
below freezing for an extended period of time, allow it to
warm up before pressing Power. Otherwise, the display
will not come on.
The dryer is now ready for use.
3
Disconnect power supply before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical
shock.
- Electrical Shock Hazard
WARNING
Ensure proper
ground exists
before use.
Raise
Lower
20 49-3000193 Rev 1
ENGLISH
INSTALLATION INSTRUCTIONS
HAIER APPLIANCES STACK KIT
Visit our website at haierappliances.com/parts or in
Canada visit haiercanada.ca/parts.
Part Number Accessory
GFA24KITL Complete Stack Kit
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT Save these instructions for
local electrical inspector’s use.
IMPORTANT Observe all governing codes
and ordinances.
Note to Installer Be sure to leave these
instructions with the Consumer.
Note to Consumer Keep these instructions for
future reference.
• Service must be performed by a qualified installer.
Do not allow children on or in the appliance. Close
supervision of children is necessary when the
appliance is used near children.
Proper installation is the responsibility of the installer.
REQUIREMENTS FOR ALCOVE OR
CLOSET INSTALLATION
Keep flammable materials and vapors, such as gasoline,
away from dryer.
Place dryer at least 18” (46 cm) above the floor for a
garage installation.
Failure to do so can result in death, explosion, or fire.
Minimum clearance between dryer cabinet and
adjacent walls or other surfaces is:
0” either side
1” front and rear
1” top
The rear of the dryer should face a wall.
Consideration must be given to provide adequate
clearance for installation and service.
Closet doors must be louvered or otherwise
ventilated and have at least 60 square inches of open
area. If the closet contains both a washer and a dryer,
doors must contain a minimum of 120 square inches
of open area.
MINIMUM CLEARANCE OTHER THAN
ALCOVE OR CLOSET INSTALLATION
Minimum clearance to combustible surfaces and for air
opening are: 0” both sides, 1” rear and 1” top.
The rear of the dryer should face a wall.
Consideration must be given to provide adequate
clearance for installation and service.
- Explosion Hazard
WARNING
STACKING THE WASHER AND DRYER (if desired)
If you are planning to stack the washer and dryer, order Stacking Kit number GFA24KITL to be used for this dryer.
Kit sold separately.
INSTALLATION PREPARATION
Remove the packaging.
Flatten the product carton to use as a pad to lay the
dryer down on its side. Continue using the carton to
protect the finished floor in front of the installation
location.
TOOLS YOU WILL NEED
Level
Phillips
screwdriver
Gloves
KIT CONTENTS (GE APPLIANCES KIT
# GFA24KITL)
Screws (2) Long
For dryer
attachment
Bracket-
stack (R)
Bracket-
stack (L)
Screws (6) Short
For washer attachment
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84

Haier QFT15 Electric Dryer Le manuel du propriétaire

Catégorie
Sèche-linge
Taper
Le manuel du propriétaire