GE GFT14ESSMWW Front Load Ventless Condenser Electric Dryer Le manuel du propriétaire

GE is a trademark of the General Electric Company. Manufactured under trademark license.

DRYERS

SAFETY INFORMATION ..........3

USING THE DRYER

Getting Started ...................... 4

Loading ..............................8

Features ..............................8

CARE AND CLEANING ...........9

INSTALLATION

INSTRUCTIONS .....................12

Stacking (Optional) .....................20

Reversing The Door Swing (Optional).....22

TROUBLESHOOTING TIPS..... 24

LIMITED WARRANTY ...........27

CONSUMER SUPPORT ..........28

GFT14

OWNER’S MANUAL &

INSTALLATION

INSTRUCTIONS

Write the model and serial

numbers here:

Model #_________________

Serial # _________________

They are on the label on the front

of the dryer behind the door.

ENGLISH/FRANÇAIS/

ESPAÑOL

0020507767Z 49-3000311 Rev 3 07-23 GEA

249-3000311 Rev 3

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-3000311 Rev 3 3

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

To reduce the risk of fire, explosion, electric shock, or injury to persons when using your appliance,

follow basic precautions, including the following:

Ŷ

Read all instructions before using the appliance.

Ŷ

DO NOT dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or

explode.

Ŷ DO NOT place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to contaminated loads, the final

part of the tumble dryer cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the end

of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

Ŷ

DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this

appliance is used near children.

Ŷ

Before the appliance is removed from service or discarded, remove the door to the drying compartment.

Ŷ

DO NOT reach into the appliance if the drum is moving.

Ŷ

DO NOT install or store this appliance where it will be exposed to the weather.

Ŷ

DO NOT tamper with controls.

Ŷ

DO NOT climb or stand on this unit.

Ŷ DO NOT repair or replace any part of this appliance or attempt any servicing unless specifically recommended

in the user-maintenance instructions or in published user-repair instructions that you understand and have the

skills to carry out.

Ŷ Follow all fabric care instructions and warnings to prevent melting of garments or damage to the appliance.

Ŷ

DO NOT use fabric softeners or products to eliminate static unless recommended by the manufacturer of the

fabric softener or product.

Ŷ

DO NOT dry articles containing foam rubber or similarly textured rubber-like materials.

Ŷ

Clean lint screen and clean and empty the condenser before or after each load.

Ŷ

DO NOT operate the dryer without the lint filter and condenser in place.

Ŷ DO NOT store combustible materials, gasoline or other flammable liquids near the dryer. Keep area around the air

intake vent on the front of the dryer and adjacent surrounding areas free from the accumulation of lint, dust and dirt.

Ŷ

The interior of the appliance should be cleaned periodically by qualified service personnel.

Ŷ

Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power or Start/Pause button DOES

NOT disconnect power.

Ŷ

DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or

broken parts, including a damaged cord or plug.

Ŷ

DO NOT spray any type of aerosol into, on or near dryer at any time. DO NOT use any type of spray cleaner when

cleaning dryer interior. Hazardous fumes or electrical shock could occur

.

Ŷ

See “ELECTRICAL CONNECTION” located in the Installation Instructions for grounding instructions.

WARNING

SAFETY INFORMATION

Proper Disposal of your Appliance

Ŷ

Dispose of or recycle your appliance in accordance with Federal and Local Regulations. Contact your local

authorities for the environmentally safe disposal or recycling of your appliance.

Ŷ

Consider recycling options for your appliance packaging material.

449-3000311 Rev 3

Getting started

USING THE DRYER

Throughout this manual, features and appearance may vary from your model.

Controls

• If the screen is dark,

press the Power button

to “wake up” the display.

Step 2 Step 3 Step 4

Step 1

• Select a dry cycle.

(Defaults are set for

each dry cycle. These

default settings can

be changed. See

control settings for

more information.)

OR

• Press the

Start/Pause

button.

• Loosely add items.

• Close door.

NOTE: Dryer will not start

with door open.

To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY

INFORMATION before operating this appliance.

WARNING

Power

• Press Timed Dry

button, rotate knob

to adjust time, and

press Temp button

to set your own

temperature.

Start

Pause

Temp

Timed

Dry

Damp DelayDamp

Dry

Ex Dry

Damp Timed

Clean Filter

No Heat

Low

High

Medium

DRY DAMP COOL

Est Time Remaining

Tumble

My Cycle

Power

Start

Pause

Warm Up

Rack Dry

Quick Dry

Delicates

Cottons

Heavy

Duty

Active

Wear

Casuals

To w e l s

Sanitize

Dewrinkle

Empty Tank

Mixed Loads

Timed

Dry

Damp

Alert

Level Ext

Tumble

My Cycle

Temp eDry

Hold to Set

Delay

Dry

C

L AKBM

D E F H I J

N

G

49-3000311 Rev 3 5

USING THE DRYER

Getting started

BDry Cycles

The dry cycle controls the cycle time for the drying process. The chart below will help you match

the dry setting with the loads.

Mixed Loads

or Normal

(Depending on

model)

For loads consisting of cottons and poly blends.

Cottons For cottons and most linens. NOTE: Energy Star® models are tested on Cottons with

default settings.

Heavy Duty For large coats, bed spreads, mattress covers, sleeping bags, blankets, comforters, jackets,

small rugs, and similar large and bulky items.

Towels Use for towels OR sheets. It is not recommended to mix towels and sheets in the same load.

Casuals For wrinkle-free, permanent press and delicate items, and knits.

Active Wear Clothing worn for active sports exercise and some casual wear. Fabrics include new technology

finishes and stretch fibers such as Spandex. Also for clothing labeled Easy Care or Perma Press:

For wrinkle-free and permanent press items.

Sanitize Reduces certain types of bacteria by 99.6%, including: Staphylococcus aureus and Pseudomonas

aeruginosa. The antibacterial process occurs when high heat is used during a portion of this

drying cycle.

Quick Dry For small loads that are needed in a hurry, such as sports or school uniforms. Can also be

used if the previous cycle left some items damp, such as collars or waistbands.

Delicates For lingerie and special-care fabrics.

Dewrinkle For removing wrinkles from items that are dry or slightly damp. This cycle is not recommended

for delicate fabrics.

Warm Up Provides 25 minutes of warming time to warm up clothes.

Air Fluff Provides 30 minutes of tumbling time without heat.

Rack Dry For drying delicate items without tumbling, use drying rack accessory. Place items flat on the

drying rack such as wool sweaters and delicate fabrics. Dry with low heat.

APower

Press to “wake up” the display. If the display is active, press to turn the dryer off.

NOTE: Pressing Power does not disconnect the appliance from the power supply.

CTemp (Temperature)

You can change the temperature of your dry cycle.

Temp

High For regular to heavy cottons.

Medium For synthetics, blends and items labeled Permanent Press.

Low For delicates, synthetics and items labeled Tumble Dry Low.

No Heat This option may only be used with Air Fluff and Timed Dry, in which items are

tumbled without heat.

649-3000311 Rev 3

Getting started

USING THE DRYER

Extended Tumble

Minimizes wrinkles by adding approximately 2 hours of no-heat tumbling after clothes are

dry.

The estimated time remaining display will show “END”.

The extended tumble time does not get added to the cycle time on the display.

I

DLevel

The sensor continuously monitors the amount of moisture in the load. When the moisture in

your clothes reaches your selected dry level, the dryer will stop.

NOTE: Sensor dry Level can be used with all cycles except Timed Dry, Air Fluff, Rack

Dry, Warm Up and Dewrinkle.

EDamp Alert

This option causes the dryer to beep when clothes have dried to a damp level. Remove

items that you wish to hang dry. The Damp Alert will only beep when this option is selected,

and the dryer will continue to dry.

Removing clothes and hanging them when they are damp can reduce the need to iron some items.

Damp

Alert

FTimed Dry

1. Press Timed Dry button. Lights around the knob will flash. Select the drying time by

rotating the knob to increase or decrease the time in 10-minute increments up to 2 hours

and 30 minutes.

2. Select the dry Temp.

3. Close the door.

4. Press Start/Pause.

HMy Cycle

Set up your favorite combination of settings and save them here for one touch recall. These

custom settings can be set while a cycle is in progress.

To store a My Cycle combination of settings:

1. Select your drying cycle.

2. Change Temp and Level settings to fit your needs.

3. Select any drying options you want.

4. Press and hold the My Cycle button for 3 seconds to store your selection. A beep will

sound and the button will light up.

To recall your stored My Cycle combination:

Press the MY CYCLE button before drying a load.

To change your stored My Cycle combination:

Repeat steps 1–4.

My Cycle

Hold to Set

Level

Ex Dry Use for heavy-duty fabrics or items that should be very dry, such as towels.

Dry Use for normal dryness level suitable for most loads. This is the preferred cycle for energy saving.

Damp For leaving items partially damp.

Timed

Dry

Tumble

Ext

GeDry (on some models)

Reduces total energy consumption of specific dryer cycles by adjusting certain heat settings.

NOTE: Cycle times will change when eDry is selected.

Energy Star® models are tested on Cottons cycle with default settings to determine energy

use rating of this dryer. The eDry option will default to on for Cottons. Temperature settings

on High and dryness level setting on Dry are specifically designed for this cycle to reduce

energy consumption. For optimal energy savings, turn eDry on. For optimal drying times,

turn eDry off. Energy savings will vary across loads and cycles.

The eDry selection can be used with Mixed Loads, Cottons, Heavy Duty, Towels,

Casuals, Active Wear and Delicates.

eDry

49-3000311 Rev 3 7

USING THE DRYER

Getting started

JDelay Dry

Use to delay the start of your dryer.

1. Choose your dry cycle and any options.

2. Press Delay Dry. You can change the delay time in 1 hour increments, using the Delay Dry

button.

3. Press the Start/Pause button to start the countdown.

NOTE: If the door is opened while the dryer is in Delay Dry, the countdown time will not

restart unless the door is closed and Start/Pause button has been pressed again.

KStart/Pause

Press to start a cycle. If the dryer is running, pressing it once will pause the dryer and unlock

the door. This function can be used to add garments during a cycle. Press again to restart

the cycle.

NOTE: If the dryer is paused and the cycle is not restarted within 15 minutes, the current

cycle will be cancelled.

LLock

You can lock the controls to prevent any selections from being made. Or you can lock or

unlock the controls after you have started a cycle.

Children cannot accidentally start the dryer by touching pads with this option selected.

To lock the dryer, press and hold the Temp and Level buttons together for 3 seconds.

To unlock the dryer controls, press and hold the Temp and Level buttons together for 3

seconds. A sound is made to indicate the lock/unlock status.

The control lock icon on the display will light up when it is on.

NOTE: The Power button can still be used when the machine is locked.

Level

Temp

Start

Pause

MSignal

When the light is on, the dryer will beep at the end of the cycle and every time you press a

button on the control panel.

To turn the signal off, press and hold the Level and Damp Alert buttons together for 3

seconds. A sound is made to indicate the lock/unlock status.

Delay

Dry

Damp

Alert

Level

NDisplay and Status Lights

The display shows the approximate time remaining until the end of the cycle.

In addition, this display will show the dryer status:

Damp DelayDamp

Dry

Ex Dry

Damp Timed

Clean Filter

No Heat

Low

High

Medium

DRY DAMP COOL

Est Time Remaining

Tumble

My Cycle

Empty Tank

Status DRY DAMP COOL

Controls locked on.

End of cycle signal on.

Clean Filter Time to clean the filter. See the Care and Cleaning section.

Empty Tank Time to empty the water tank. See the Care and Cleaning section.

Temp Shows High, Medium, Low or No Heat temperature setting selected.

Level Shows Extra Dry, Dry or Damp dryness setting selected.

Damp Alert Indicates Damp Alert is set and will sound when the clothes have dried to a damp

dryness level.

Timed Indicates that a Timed Dry cycle is set. Will turn off after cycle is finished.

Est Time

Remaining Display shows the estimated time remaining until set cycle is completed.

My Cycle Indicates the My Cycle feature is set.

Ext Tumble Indicates the Extended Tumble feature is set.

Indicates Delay Dry is set time is selected.

849-3000311 Rev 3

Loading

USING THE DRYER

Fabric Care Labels

Below are fabric care label “symbols” that affect the clothing you will be laundering.

Dry Labels

Always follow fabric manufacturer’s care label when laundering.

As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Try also to

sort items according to size. For example, do not dry a sheet with socks or other small items.

Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce®

Fabric Conditioner Dryer Sheets have been approved for use in this dryer when used in accordance with the

manufacturer’s instructions.

Do not overload. This wastes energy and causes wrinkling.

• Keep flammable materials and vapors, such as

gasoline, away from dryer.

• DO NOT dry anything that has ever had anything

flammable on it (even after washing).

• No washer can completely remove oil.

• DO NOT dry anything that has ever had any type of oil

on it (including cooking oils).

• Items containing foam, rubber, or plastic must be dried

on a clothesline.

• Failure to do so can result in death, explosion, or fire.

Sorting and Loading Hints

Tumble

dry

Dry Normal Permanent Press/

wrinkle resistant Gentle/

delicate Do not tumble dry Do not dry

(used with

do not wash)

Heat

setting

High Medium Low No heat/air

Special

instructions Line dry/

hang to dry Drip dry Dry flat In the shade

- Fire Hazard

WARNING

Drying Rack

A handy drying rack may be used for drying delicate items such as washable sweaters. Place items flat on the

drying rack and block such items as wool sweaters and delicate fabrics. Dry with low heat.

To install the drying rack, extend the drying rack into the dryer drum and rest the front two

legs on the front angled ledge.

NOTES:

Ŷ The drying rack is designed for use with the Timed Dry cycle. Use with sensor cycles

may result in damp items or extended cycle times.

Ŷ Do not use this drying rack when there are other clothes in the dryer, that are not placed on the rack.

Ŷ The drying rack, WE01X26416, is available as an accessory. Order on-line at GEApplianceparts.com, 24 hours

a day or by phone at 877.959.8688 during normal business hours.

49-3000311 Rev 3 9

CARE AND CLEANING

Care and cleaning

Exterior

Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged

by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric

may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your

warranty.

Stainless Steel

To clean stainless steel surfaces use a damp cloth with a mild, non-abrasive cleaner suitable for stainless steel

surfaces. Remove the cleaner residue and then dry with a clean cloth.

The stainless steel used to make the dryer drum provides the highest reliability available in a GE Appliances dryer.

If the dryer drum should be scratched or dented during normal use, the drum will not rust or corrode. These surface

blemishes will not affect the function or durability of the drum.

Interior

The interior of the appliance should be cleaned once a year by qualified service personnel.

Lint Filter

Clean the lint filter before each use.

Pull out the lint filter. Moisten your fingers and remove the captured lint. Once clean, slide

the filter back into position. Have a qualified technician vacuum the lint from the dryer once

a year.

NEVER OPERATE THE DRYER WITHOUT ITS FILTER IN PLACE.

Drum Lamp

NOTE: The drum lamp is not consumer replaceable on models where there is a flat cover

over an LED bulb. If this light should ever stop working, call for service.

For models that have a domed cover over the bulb secured by a screw:

Before replacing the light bulb, be sure to unplug the dryer power cord or disconnect the

dryer at the household distribution panel by removing the fuse or switching off the circuit

breaker. Reach above dryer opening from inside the drum to locate the light.

Remove the screw and the plastic cover to access the bulb. Replace with the appropriate

bulb and then reaffix the cover and screw.

Order replacement bulb WE11X26351 on-line at GEApplianceparts.com, by phone at 877.959.8688 during normal

business hours, or purchase appliance bulb 7C7 from your local retailer.

When the door is opened, the drum lamp automatically turns on and remains on for 2 minutes. When the door is closed,

the drum lamp will remain on for 30 seconds.

Disconnect power supply before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING - Shock Hazard

Certain internal parts are intentionally not grounded and may present a risk of electric shock only during

servicing.

Service personnel – DO NOT contact the following parts while the appliance is energized: motor start capacitor,

motor metal holder, and drum wheel shaft.

- Electrical Shock Hazard

WARNING

10 49-3000311 Rev 3

Care and cleaning

CARE AND CLEANING

Water Tank

REMOVE THE CONDENSED WATER IN THE TANK AFTER EVERY DRYING CYCLE.

NOTE: If drain hose is installed, emptying the water tank is not required. See the

CONNECTING THE DRAIN HOSE section in the Installation Installations of this manual.

• Pull out the water tank.

When removing the water tank from the product, hold it using both hands as it is

heavy and take care not to spill any water inside the tank.

• Remove the condensed water inside the water tank.

To avoid over filling, which could lead to water leaking outside the unit, drain

water left in water tank after each cycle. Over filling will cause cycle to stop

prematurely until emptied.

NOTE: When the Empty Tank indicator light is on, the dryer will not operate until

the tank is emptied and the indicator has been cleared. Press the Start button and

the indicator light will turn off and the dryer will resume the cycle.

Condenser

THE CONDENSER SHOULD BE CLEANED ONCE PER MONTH.

• Open the condenser compartment cover.

• Unlock both locking tabs.

• Remove the condenser box from

the condenser compartment.

• Clean the condenser box and inside the condenser compartment completely. Use tap

water to clean between the grooves of the condenser box by allowing tap water to flow

through it. Reach inside the condenser compartment and wipe away all debris. Make

sure the rubber gaskets on the condenser box are free of debris before reinstalling.

NOTES:

• Make sure to clean your condenser once per month to prevent degradation of the

dryer’s performance.

• When assembling the condenser after cleaning it, make sure the locking tabs are set to

the lock position. Never run the dryer without the condenser installed.

Unlock

Drain hole

is on the

top rear of

the drawer

49-3000311 Rev 3 11

NOTES

Notes

12 49-3000311 Rev 3

Installation

Dryer

Instructions

If you have any questions, call GE Appliances at 800.GE.CARES

(800.432.2737) or visit our Website at: GEAppliances.com

In Canada, call 800.561.3344 or visit www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT – Save these instructions for

local electrical inspector’s use.

• IMPORTANT – Observe all governing

codes and ordinances.

• Install the clothes dryer according to the

manufacturer’s instructions and local codes.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Clothes dryer installation must be performed by a

qualified installer.

• Before the old dryer is removed from service or

discarded, remove the dryer door.

• Service information and the wiring diagram are

located in the control console.

• Do not allow children on or in the appliance. Close

supervision of children is necessary when the

appliance is used near children.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• Install the dryer where the temperature is above

50°F for satisfactory operation of the dryer control

system.

• Risk of Fire - Clothes dryer installation must be

performed by a qualified installer.

• Install the clothes dryer according to these

instructions and local codes.

• DO NOT install or store this appliance in any

location where it could be exposed to water or

weather.

• To reduce the risk of severe injury or death, follow

all installation instructions.

• Save these instructions. (Installers: Be sure to

leave these instructions with the customer.)

- Fire Hazard

WARNING

If you are planning to stack the washer and dryer, order

Stacking Kit number GFA24KITL to be used for this

dryer. Kit sold separately.

49-3000311 Rev 3 13

*NOTE:

With leveling legs retracted: 33-1/4 (84.5 cm)

With leveling legs fully extended: 33-5/8 (85.4 cm)

Stacked: 66-1/2” (168.9 cm)

Installation Instructions

Tilt the dryer sideways and remove the foam shipping pads by pulling at the sides and

breaking them away from the dryer legs. Be sure to remove all of the foam pieces

around the legs.

Remove the bag containing the literature.

UNPACKING YOUR DRYER

DRYER

DIMENSIONS

Front

View

23-7/16”

(59.5 cm)

*33-1/4”

(84.5 cm)

Side View

25-1/4” (64.1 cm)

42-13/16” (108.7 cm)

POWER CORDS

GE Appliances strongly recommends the use of

factory specified parts. Select the power cord to fit your

installation requirements.

Order on-line at GEApplianceparts.com today,

24 hours a day or by phone at 877.959.8688 during

normal business hours. In Canada, visit your local

GE Appliances parts distributor or call 800.661.1616

or

GEAppliances.ca/en/products/parts-filters-accessories.

Part Number Type Length Amperage

WX9X2 3-Prong 4 Feet 30

WX9X3 3-Prong 5 Feet 30

WX9X4 3-Prong 6 Feet 30

WX9X18 4-Prong 4 Feet 30

WX9X19 4-Prong 5 Feet 30

WX9X20 4-Prong 6 Feet 30

*33-1/4”

(84.5 cm)

ELECTRICAL CONNECTION

DIMENSIONS

Back

View

30”

(76.2 cm)

20-1/2”

(52.1 cm)

14 49-3000311 Rev 3

Installation Instructions

MOBILE OR MANUFACTURED

HOME INSTALLATION

• Installation MUST conform to the

MANUFACTURED HOME CONSTRUCTION

AND SAFETY STANDARD, TITLE 24, PART

3280 or STANDARD FOR MOBILE HOMES

CAN/CSA-Z240 MH, or, when such standards

are not applicable, with AMERICAN NATIONAL

STANDARD FOR MOBILE HOME, ANSI/NFPA

NO. 501B.

• Provide an opening with a free area of at least 25

square inches for introduction of outside air into

the dryer room.

• See the sections for electrical connection information.

REQUIREMENTS FOR ALCOVE OR

CLOSET INSTALLATION

Keep flammable materials and vapors, such as gasoline,

away from dryer.

Place dryer at least 18” (46 cm) above the floor for a

garage installation.

Failure to do so can result in death, explosion, or fire.

• Minimum clearance between dryer cabinet and

adjacent walls or other surfaces is:

0” either side

1” front and rear

1” top

• The rear of the dryer should face a wall.

• Consideration must be given to provide adequate

clearance for installation and service.

• Closet doors must be louvered or otherwise

ventilated and have at least 60 square inches of

open area. If the closet contains both a washer

and a dryer, doors must contain a minimum of 120

square inches of open area.

MINIMUM CLEARANCE OTHER

THAN ALCOVE OR CLOSET

INSTALLATION

Minimum clearance to combustible surfaces and for

air opening are: 0” both sides, 1” rear and 1” top.

The rear of the dryer should face a wall.

Consideration must be given to provide adequate

clearance for installation and service.

- Explosion Hazard

WARNING

UNDERCOUNTER INSTALLATION

If an undercounter installation is desired:

• No special dryer installation kit is required.

• If the dryer is installed alone, a minimum of 60

square inches of open area is required. If a washer

and dryer are installed together, a minimum of 120

square inches of open area is required.

BATHROOM OR BEDROOM

INSTALLATION

The installation must conform with local codes or,

in the absence of local codes, with the NATIONAL

ELECTRICAL CODE, ANSI/NFPA NO. 70 (for electric

dryers).

60

square

inches

min.

open

area

Dryer Installed Alone

Countertop and side cabinets

Washer and Dryer Installed Together

Countertop and side cabinets

120

square

inches

min.

open

area

49-3000311 Rev 3 15

Installation Instructions

CONNECTING AN ELECTRIC DRYER

Before making the electrical connection, turn off the

circuit breaker(s) or remove the dryer’s circuit fuse(s) at

the electrical box. Be sure the dryer cord is unplugged

from the wall. NEVER LEAVE THE ACCESS COVER

OFF THE TERMINAL BLOCK.

MATERIALS YOU WILL NEED

Ŷ

Safety glasses

Ŷ

Gloves

Ŷ

Dryer power cord kit

(not provided with dryer)

UL rated 120/240V, 30A with

3 or 4 prongs. Identify the

plug type as per the house

receptacle before purchasing

line cord.

Stacking installations may

require a power cord up to 6

feet in length.

TOOLS YOU WILL NEED

Ŷ

Slip-joint pliers

Ŷ

Flat-blade

screwdriver

Ŷ

Phillips

screwdriver

Ŷ

Level

Ŷ

3/4” Strain relief

(UL recognized)

Disconnect power supply before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING - Shock Hazard

Certain internal parts are intentionally not grounded

and may present a risk of electric shock only during

servicing.

Service personnel – DO NOT contact the following

parts while the appliance is energized: motor start

capacitor, motor metal holder, and drum wheel shaft.

- Electrical Shock Hazard

WARNING

RECEPTACLE FOR CONNECTION

TO SPECIFIED WASHERS

Receptacle

Not a general-use

receptacle – For use

with washers

GFW148 or QFW150,

GFQ14 only.

16 49-3000311 Rev 3

For direct wire connections:

Use 10 gauge copper wire.

Use a UL-listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining two supply wires to remaining two

terminals.

Securely tighten all electrical connections.

Replace the terminal block cover.

Failure to do so can result in death, fire or electrical shock.

GROUNDING INSTRUCTIONS

For a permanently connected dryer: This dryer

must be connected to a grounded metal, permanent

wiring system, or an equipment-grounding conductor

must be run with the circuit conductors and

connected to the equipment-grounding terminal on

the appliance.

Improper connection of the

equipment-grounding conductor can

result in a risk of electric shock. Check with a qualified

electrician, or service representative or personnel, if

you are in doubt as to whether the appliance is properly

grounded.

SAVE THESE INSTRUCTIONS

- Fire Hazard

WARNING

Use a new UL-listed 240V 30 amp dryer power supply

cord with closed ring terminals or spade terminals with

upturned ends.

Use a UL-listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining two supply wires to remaining two

terminals.

Securely tighten all electrical connections.

Replace the terminal block cover.

Failure to do so can result in death, fire or electrical shock.

For electrical connections using a

power cord:

GROUNDING INSTRUCTIONS

For a grounded, cord-connected dryer: This dryer

must be grounded. In the event of a malfunction or

breakdown, grounding will reduce the risk of electric

shock by providing a path of least resistance for

electric current. This dryer uses a cord having an

equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate

outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Improper connection of the

equipment-grounding conductor can

result in a risk of electric shock. Check with a qualified

electrician, or service representative or personnel, if

you are in doubt as to whether the appliance is properly

grounded. DO NOT modify the plug on the power supply

cord. If it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

- Fire Hazard

WARNING

ELECTRICAL CONNECTION

INFORMATION FOR ELECTRIC

DRYERS

ELECTRICAL CONNECTION

INFORMATION FOR ELECTRIC

DRYERS

Installation Instructions

TO PREVENT ELECTRIC SHOCK, DISCONNECT

POWER BEFORE SERVICING.

This dryer should be connected to an individual branch

circuit with 10 gauge copper wire minimum through a

30 amp fuse or circuit breaker. DO NOT fuse neutral.

Use copper conductors only.

- Electrical Shock Hazard

WARNING

TO PREVENT ELECTRIC SHOCK, DISCONNECT

POWER BEFORE SERVICING.

This dryer should be connected to an individual branch

circuit with 10 gauge copper wire minimum through a

30 amp fuse or circuit breaker. DO NOT fuse neutral.

Use copper conductors only.

- Electrical Shock Hazard

WARNING

49-3000311 Rev 3 17

Installation Instructions

CONNECTING DRYER USING

3-WIRE CONNECTION

CONNECTING DRYER USING

4-WIRE CONNECTION (MUST

BE USED FOR MOBILE HOME

INSTALLATION)

NOTE: Since January 1, 1996, the National Electrical

Code requires that new constructions use a 4-wire

connection to an electric dryer. A 4-wire cord must

also be used where local codes do not permit grounding

through the neutral. 3-wire connection is NOT for use

on new construction.

1. Turn off the circuit breaker(s) (30 amp) or remove

the dryer’s circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall

receptacle.

3. Remove the power cord cover located at the upper

back.

4. Remove green ground screw and retain for use in

Step 7. Remove center screw (marked N) in terminal

block. Remove and discard ground strap.

5. Install 3/4 in. UL-recognized strain relief to power

cord entry hole. Bring power cord through strain

relief and bracket.

6. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

7. Attach ground wire of power cord with the green

ground screw (hole above strain relief bracket).

Tighten all terminal block screws (3) securely.

8. Properly secure power cord to strain relief and

bracket.

9. Reinstall the cover.

NEVER LEAVE THE COVER OFF OF THE

TERMINAL BLOCK.

NEVER LEAVE THE COVER OFF OF THE

TERMINAL BLOCK.

3-wire Connection

Not for use in Canada.

DO NOT use for Mobile Home Installations.

NOT for use on new construction.

NOT for use on recreational vehicles.

NOT for use in areas where local codes prohibit

grounding through the neutral conduction.

1. Turn off the circuit breaker(s) (30 amp) or remove

the dryer’s circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall

receptacle.

3. Remove the power cord cover located at the upper

back.

4. Install 3/4-in. UL-recognized strain relief to power

cord entry hole. Bring power cord through strain

relief and bracket.

5. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of

the terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

6. Be sure ground strap is connected to green ground

screw on cabinet rear. Tighten all terminal block

screws (3) securely.

7. Properly secure power cord to strain relief and

bracket.

8. Reinstall the cover.

L1 NL2

Green wire

from power

cord

3/4” Strain

Relief and

Bracket

Cover

4 #10 AWG minimum copper conductors or 120/240V 30A

power supply cord kit marked for use with dryers and provided

with closed loop or spade terminals with upturned ends (not

supplied).

White Wire

Black

or Red

Wire

Black

or

Red

Wire

If required, by local code, install external ground (not

provided) to grounded metal, cold water pipe, or other

established ground determined by a qualified electrician.

L1 NL2

Black or Red Wire

3/4” Strain

Relief and

Bracket

Cover

3 #10 AWG minimum copper conductors or 120/240V 30A

power supply cord kit marked for use with dryers and provided

with closed loop or spade terminals with upturned ends (not

supplied).

Ground

Strap

White Wire

Black

or Red

Wire

18 49-3000311 Rev 3

Installation Instructions

CONNECTING THE DRAIN HOSE

DRAINING WATER WITHOUT USING

THE WATER TANK

You can use the dryer without using the water tank by

following the procedures below.

CONNECTING THE DRAIN HOSE

The dryer can pump the condensed water outside of

the DRYER directly with drain hose provide.

The procedures to connect the drain hose are as

follows.

1. Disconnect the drain hose A.

2. Connect the drain hose A to

the other hole.

3. Connect accessory hose B

(long drain hose) adjacent to

hose A.

• When connecting hose B, take care that the height of

the hose does not exceed 47” (120 cm).

• After connecting the drain hose, you can now

directly drain the condensed water to a standpipe or

washstand.

CONNECTING THE DRAIN HOSE

(CONT.)

4. Over the edge of a wash basin: The drain hose must

be placed lower than 47” (120 cm) and higher than

30” (76 cm). To keep the drain hose spout bent, use

the supplied plastic hose guide. Secure the guide

to the wall with a hook or to the tap with a piece of

string to prevent the drain hose from moving.

5. Assemble the drain hose and the hose guide and fix

them with the cable-tie.

Do not push the drain hose in the standpipe any further

than 4” (10 cm). Pushing the drain hose further in the

standpipe can cause leaking.

Back

View

A

B

47”

(120 cm)

Max.

Drain Hose Hose Guide

Cable Ties

49-3000311 Rev 3 19

Installation Instructions

LEVEL THE DRYER

Raise

Lower

PLUG DRYER IN

Ensure proper

ground exists

before use.

1

FINAL SETUP

2

DRYER STARTUP

Press the Power button.

NOTE: If the dryer has been exposed to temperatures

below freezing for an extended period of time, allow

it to warm up before pressing Power. Otherwise, the

display will not come on.

The dryer is now ready for use.

3

NOTE: Stacking installations may require a power

cord up to 6 feet in length.

Stand the dryer upright near the final location and

adjust the four leveling legs at the corners to ensure

that the dryer is level from side to side and front to

rear. Power

20 49-3000311 Rev 3

Installation Instructions

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT – Save these instructions for

local electrical inspector’s use.

• IMPORTANT – Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Service must be performed by a qualified installer.

• Do not allow children on or in the appliance. Close

supervision of children is necessary when the

appliance is used near children.

• Proper installation is the responsibility of the installer.

REQUIREMENTS FOR ALCOVE OR

CLOSET INSTALLATION

Keep flammable materials and vapors, such as gasoline,

away from dryer.

Place dryer at least 18” (46 cm) above the floor for a

garage installation.

Failure to do so can result in death, explosion, or fire.

• Minimum clearance between dryer cabinet and

adjacent walls or other surfaces is:

0” either side

1” front and rear

1” top

• The rear of the dryer should face a wall.

• Consideration must be given to provide adequate

clearance for installation and service.

• Closet doors must be louvered or otherwise

ventilated and have at least 60 square inches of

open area. If the closet contains both a washer

and a dryer, doors must contain a minimum of 120

square inches of open area.

MINIMUM CLEARANCE OTHER

THAN ALCOVE OR CLOSET

INSTALLATION

Minimum clearance to combustible surfaces and for

air opening are: 0” both sides, 1” rear and 1” top.

The rear of the dryer should face a wall.

Consideration must be given to provide adequate

clearance for installation and service.

- Explosion Hazard

WARNING

GE APPLIANCES STACK KIT

Order on-line at GEApplianceParts.com, 24 hours

a day or by phone at 877.959.8688 during normal

business hours.

Part Number Accessory

GFA24KITL Complete Stack Kit

STACKING THE WASHER AND DRYER (if desired)

If you are planning to stack the washer and dryer, order Stacking Kit number GFA24KITL to be used for this dryer.

Kit sold separately.

INSTALLATION PREPARATION

Remove the packaging.

Flatten the product carton to use as a pad to lay the

dryer down on its side. Continue using the carton to

protect the finished floor in front of the installation

location.

TOOLS YOU WILL NEED

Ŷ

Level

Ŷ

Phillips

screwdriver

Ŷ

Gloves

KIT CONTENTS (GE APPLIANCES

KIT # GFA24KITL)

Screws (2) Long

For dryer

attachment

Bracket-

stack (R)

Bracket-

stack (L)

Screws (6) Short

For washer attachment

La page charge ...

GE GFT14ESSMWW Front Load Ventless Condenser Electric Dryer Le manuel du propriétaire

Ce manuel convient également à

GE GFT14ESSMWW Front Load Ventless Condenser Electric Dryer Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents