Progress Lighting P250060-028-30 Mode d'emploi

Ceiling Fan Installation Manual

P250060

93131624_B

Date Pu rch ased

Store Purchased

Model No .

Serial No.

Vendor No .

UPC

126751

785247245437

785247245444

785247245420

Limited Lifetime Warranty

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so

long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to

be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic

blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of

any sea coast. Extended warranties for ENERGY STAR® qualified products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are

warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance

with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for

fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical

components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no

warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for

replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864) 678-1000 for repair or replacement

which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not

limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or

neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without

limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or

attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND

ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS

LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR

CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,

BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,

WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE OR NONINFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or

consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights

and you may have other rights which vary from state to state.

Table of Contents

Safety Rules.....................................................................................................................................................................................

Unpacking Your Fan .......................................................................................................................................................................

Installing Your Fan ..........................................................................................................................................................................

Installing the Light Kit.....................................................................................................................................................................

Operating Your Transmitter .............................................................................................................................................................

Care of Your Fan ..........................................................................................................................................................................

Troubleshooting ............................................................................................................................................................................

Specifications ................................................................................................................................................................................

1.

2.

3.

8.

9.

11.

12.

13.

1. Safety Rules

1. To reduce the risk of electric shock, insure electricity has been turned off

at the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan with any solid-state fan speed control device.

4. WARNING: To reduce the risk of fire, electric shock, or personal injury,

mount to outlet box marked "Acceptable for Fan Support of 15.9 kg (35 lbs.)

Or Less" and use mounting screws provided with the outlet box. Most outlet

boxes commonly used for the support of light fixtures are not acceptable for

fan support and may need to be replaced. Due to the complexity of the

installation of this fan, a qualified licensed electrician is strongly

recommended.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less.

Use only CUL-listed outlet boxes marked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 ft (2.1m) clearance from

the trailing edge of the blades to the floor.

7. Avoid placing objects in the path of the blades.

8. To avoid personal injury or damage to the fan and other items, be

cautious when working around or cleaning the fan.

9. Do not use water or detergents when cleaning the fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

10. After making electrical connections, spliced conductors should be

turned upward and pushed carefully up into the outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor on one side of the outlet box.

11. Electrical diagrams are for reference only. Light kits that are not packed

with the fan must be UL Listed and marked suitable for use with the

model fan you are installing. Switches must be UL General Use

Switches. Refer to the Instructions packaged with the light kits

NOTE

READ AND SAVE ALL INSTRUCTIONS!

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

Unpack your fan and check the contents. You should have the following items:

Unpacking Your Fan 2.

13. Loose parts bag containing:

a. Blade attachment hardware

1/4” x12mm screw (1)

b. Flywheel attachment hardware

3/16” x 9 screw (1)

1. Fan blades (3)

2. Canopy &

mounting bracket

3. Canopy cover

4. Ball/downrod assembly

5. Collar cover

6. Fan motor assembly

7. Flywheel

8. Mounting plate

9. LED light kit

10. Diffuser

11. Receiver with 9 wire nuts

12. Transmitter assembly

4

5

6

3

2

1

7

8

9

10

11

13

ab

12

Tools Required

Phillips screw driver, straight slot screw driver,

adjustable wrench, step ladder, and wire cutters.

Mounting Options

If there isn't an existing cUL listed mounting box,

then read the following instructions. Disconnect

the power by removing fuses or turning off

circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the

fan (at least 35 lbs). Do not use plastic outlet

boxes.

3. Installing Your Fan

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR OTHER PERSONAL INJURY,

MOUNT FAN ONLY TO AN OUTLET BOX

MARKED ACCEPTABLE FOR FAN SUPPORT

AND USE THE MOUNTING SCREWS

PROVIDED WITH THE OUTLET BOX. OUTLET

BOXES COMMONLY USED FOR THE

SUPPORT OF LIGHTING FIXTURES MAY NOT

BE ACCEPTABLE FOR FAN SUPPORT AND

MAY NEED TO BE REPLACED. CONSULT A

QUALIFIED ELECTRICIAN IF IN DOUBT.

Figure

1

Figure

3

Figure

4

Figure

2

Outlet box

Outlet box Outlet box

Note: You may need a longer downrod to

maintain proper blade clearance when installing

on a steep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at your Progress Lighting Retailer).

Angled ceiling

maximum

12 angle

Recessed

outlet box

Provide strong support

Ceiling

hanger

bracket

4.

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps below to hang your fan properly:

Step 1. Remove the mounting bracket from

the canopy by removing the 1 of 2 screws

from the bottom of the mounting bracket and

loosening the other one a half turn from the

screw head. Next, turn the canopy counter

clockwise to removing the mounting bracket

from the canopy. (Fig. 5)

Step 2. Pass the 120-volt supply wires

through the center hole in the ceiling hanger

bracket as shown in Fig. 6.

Step 3. Secure the mounting bracket to the

ceiling outlet box with the screws and

washers provided with your outlet box.

Step 4. Remove the hanger pin, lock pin from

the ball/downrod assembly, and loosen two

set screws from the top of the motor assembly.

(Fig. 7)

Step 5. Route wires exiting from the top of

the fan motor through the collar cover, canopy

cover, canopy and then through the ball/

downrod. (Fig. 7)

Step 6. Align the holes at the bottom of the downrod

with the holes in the collar on top of the motor

housing (Fig. 7). Carefully insert the hanger pin

through the holes in the collar and downrod. Be

careful not to jam the pin against the wiring inside the

downrod. Insert the locking pin through the hole near

the end of the hanger pin until it snaps into its locked

position, as noted in the circle inset of Fig. 7.

WARNING

FAILURE TO PROPERLY INSTALL

LOCKING PIN AS NOTED IN STEP 6

COULD RESULT IN FAN LOOSENING AND

POSSIBLY FALLING.

Figure 5

Figure 6

Figure 7

Mounting

bracket

Ceiling

canopy

Ceiling

hanger

bracket

Mounting screws

(supplied with

electrical box)

cUL Listed

electrical

box

120V Wires

Washers

Supply wires

Downrod

Hanger pin

Lock pin

Set screws

Canopy

Canopy cover

Collar cover

Collar

Pin in locked

position

Step 7. Tighten two set screws on the motor collar

into the downrod firmly. (Fig. 7)

Step 8. Place the downrod ball into the mounting

bracket socket.

Safety cable

5.

Make the Electric

Connections

WARNING: To avoid possible electrical shock,

be sure electricity is turned off at the main fuse box

before wiring.

Step 1. (Fig. 8) Insert the receiver into the

mounting bracket with the flat side of the receiver

facing the ceiling.

Step 3. (Fig. 9) Receiver to House Supply Wires

Electrical Connections: Connect the black (hot)

wire from the ceiling to the black wire marked

"AC in L" from the receiver. Connect the white

(neutral) wire from the ceiling to the white wire

marked "AC in N" from the Receiver. Secure the

wire connections with the plastic wire nuts

provided.

Figure 8

Receiver

Mounting

bracket

Step 2. (Fig. 9) Motor to Receiver Electrical

Connections: Connect the Red wire from the fan

to Red wire from the receiver. Connect the

Yellow wire from the fan to the Yellow wire

from the receiver. Connect the Gray wire from

the fan to the Gray wire from the receiver.

Connect the Blue wire from the fan to the Blue

wire marked "For Light" from the receiver.

Connect the White wire from the fan to the White

wire marked "For Light" from the receiver.

Secure wire connections with the plastic wire

nuts provided.

NOTE: Fan must be installed at a maximum

distance of 20 feet or less from the transmitting

unit for proper signal transmission between the

transmitting unit and the fan's receiving unit.

Figure 9

White (neutral)

Green or bare

copper (ground)

White ("AC IN N")

Blue ("For Light")

Ground

(green)

Outlet box

Black (hot)

Black ("AC IN L")

Red

Yellow

Gray

Receiver

Red

Yellow

Gray

White ("For Light")

Blue ("For Light")

White ("For Light")

Ground (green)

(green)

Main ground

Step 4. (Fig. 9) If your outlet box has a ground

wire (green or bare copper) connect it to the

receiver main ground wire,connect the receiver

other ground wires and hanging ball ground

wire together. Otherwise connect the mounting

bracket ground wire to the receiver main

ground wire,connect the receiver other ground

wires and hanging ball ground wire togeth-

er.Secure the wire connection with a plastic nut

provided. After connecting the wires spread

them apart so that the green and white wires are

on one side of the outlet box and black wires is

on the other side. Carefully tuck the wire

connections up into the outlet box.

NOTE: Convert your fan to WIFI by

adding a P2673-01 WIFI Module.

6.

Outlet box

Canopy cover

Canopy

Mounting

bracket

Figure 11

Figure 10

Screws

Finishing the Installation

Step 1. Tuck connections neatly into ceiling outlet

box.

Step 2. Slide the canopy up to mounting bracket and

place the key hole on the canopy over the screw on

the mounting bracket, turn canopy until it locks in

place at the narrow section of the key holes. (Fig.

11)

Step 3. Align the circular hole on canopy with the

remaining hole on the mounting bracket, secure by

tightening the two set screws. Note: Adjust the

canopy screws as necessary until the canopy and

canopy cover are snug.

WARNING

Make sure the notch on the mounting bracket properly

sits in the groove in the hanger ball before attaching

the canopy to the bracket by turning the housing until

it drops into place.

INSTALLATION OF

SAFETY SUPPORT

Secure safety cable to the building structure

with a wood screw. (wood screw not supplied)

(Fig. 10)

Mounting bracket

Safety cable

7.

Attaching the Fan Blades

Figure 13

Figure 12

Flywheel screws

Flywheel Blade

Blade

Blade screws

Fan motor

assembly

Figure 14

Step 1. Remove the six blade screws from the fan

motor assembly.

Step 2. Remove the six flywheel screws from the

flywheel.

Step 3. Attach the flywheel to one of the three

blades using two flywheel screws. (Fig. 12)

Step 4. Attach the blade with the flywheel to the

fan motor assembly using two blade screws. Attach

the other blades to the fan motor assembly. (Fig.

13)

Step 5. Reinstall the four remaining flywheel

screws to the flywheel. (Fig. 14)

Installing the Light Kit

8.

Figure 15

Installing the Mounting

Plate

Step 1.

Remove 1 of the 3 screws from the

mounting ring and loosen the other 2 screws.

(Do not remove)

Step 2.

Place the key holes on the mounting

plate over the 2 screws previously loosened from

the mounting ring, turn mounting plate until it

locks in place at the narrow section of the key

holes. Secure by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 15)

Mounting

plate

Mounting ring

Screws

CAUTION: Before starting installation,

disconnect the power by turning off the circuit

breaker or removing the fuse at fuse box. Turning

power off using the fan switch is not sufficient to

prevent electric shock.

1. Remove 1 of 3 screws from the mounting plate

and loosen the other 2 screws. (Do not remove)

2. While holding the LED light kit under the fan

motor assembly, make the 2-pin wire connections:

- White to white

- Blue to blue

3. Place the key holes in the LED light kit over

the two mounting screws previously loosened

from the mounting plate. Turn the LED light kit

until the LED light kit locks in place at the

narrow section of the key holes. Secure by

tightening the two screws previously loosened

and the one previously removed. (Fig. 16)

4. Raise the diffuser up against the LED light kit

and secure it to the fan by turning the diffuser

clockwise until snug. DO NOT OVERTIGHTEN.

(Fig. 16)

Figure 16

Screws

Diffuser

Mounting

plate

Wire connector

LED

Light kit

9.

Operating Your Transmitter

INSTALLING THE

BATTERY

Figure 17

Figure 18

Remove the back cover on the transmitter and

install a 12V battery that is included with the

remote control. (Fig. 17)

INSTALLING THE

TRANSMITTER HOLDER

Attach the remote control holder with the two

remote control holder mounting screws.(Fig.18)

LEARNING PROCESS

NOTE: After the AC power is on, do not press

any other button on the remote control before

pressing the button. Doing so will cause the

procedure to fail.

Should you desire to use another remote control

unit with your new fan, install one using the

steps below:

Within 30 seconds of turning the fan’s AC power

ON, press and hold the button for 5 seconds

to enter the learning function. Once the receiver

has detected the set frequency, the down light of

your fan, if applicable, will blink twice. There is

no indication if your fan is not equipped with a

light.

10.

Restore power to ceiling fan and test for proper

operation.

Figure 19

Figure 20

A. 1,2,3,4,5,6 buttons:

These six buttons are used to set the fan speed as

follows:

1 = low speed 2 = medium low speed

3 = medium speed 4 = medium high speed

5 = high speed 6 = Extra high speed

B. button:

This button turns the fan off.

C. button:

This button controls the light. Press and release

the button to turn the light ON or OFF. Press and

hold the button to set the desired brightness. The

light key has an auto-resume, it will stay at the

same brightness as the last time it was turned off.

D. , , button:

Pressing the ( / / ) button will

automatically turn fan off after 2, 4 or 8 hours.

E. button:

Fan reverse button

(Must be Pushed when the fan is in operation)

Speed settings for warm or cool weather depend

on factors such as the room size. Ceiling height,

number of fans and so on.

NOTE: To operate the reverse function on this

fan, press the reverse button while the fan is

running.

Warm weather - (Forward) A downward airflow

creates a cooling effect as shown in Fig. 19. This

allows you to set your air conditioner on a

warmer setting without affecting your comfort.

Cool weather - (Reverse) An upward airflow

moves warm air off the ceiling area as shown in

Fig. 20. This allows you to set your heating unit

on a cooler setting without affecting your

comfort.

11.

Care of Your Fan

Here are some suggestions to help you maintain your

fan

1. Because of the fan's natural movement, some

connections may become loose.

Check the support

connections, brackets, and blade attachments

twice a year.

Make sure they are secure.

(It is not

necessary to remove fan from ceiling.)

2. Clean your fan periodically to help maintain its new

appearance over the years. Use only a soft brush or

lint-free cloth to avoid scratching the finish. The

plating is sealed with a lacquer to minimize

discoloration or tarnishing. Do not use water when

cleaning. This could damage the motor, or the wood,

or possibly cause an electrical shock.

3. Cover small scratches with a light application

of shoe polish.

4.

There is no need to oil your fan.

The motor has

permanently lubricated bearings.

IMPORTANT

MAKE SURE THE POWER IS OFF AT THE

ELECTRICAL PANEL BOX BEFORE YOU

ATTEMPT ANY REPAIRS. REFER TO THE

SECTION "MAKING ELECTRICAL

CONNECTIONS"

Troubleshooting

12.

Solution

1. Check circuit fuses or breakers.

2. Check line wire connections to the fan and switch wire connections in the switch housing.

CAUTION: Make sure main power is off.

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade bracket to the motor hub is tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.

CAUTION: Make sure main power is off.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear during this time.

5. If using an optional light kit, make sure the screws securing the lampshade are tight.

6. Make sure the upper canopy is a short distance from the ceiling. It should not touch the ceiling.

1. Do not connect the fan with wall mounted variable speed control (s).

2. Re-do learning process.

Problem

Fan will not start.

Fan sounds noisy.

Remote control

malfunction

12.76 15.75 2.68'

0.08

0.50

2.54

33.11

61

167

2045.47

5802.48

13.

Specifications

lbs lbs

Fan Size

Speed Volts

Amps Watts RPM CFM N.W. G.W. C.F.

52"

Low

High

120

These are approximate measures. They do not include Amps and Wattage used by the light kit.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

701 Millennium Blvd.,

Greenville, SC 29607

Manuel d’installation du ventilateur de plafond

P250060

93131624_B

SOIENT LIÉS À UNE VIOLATION DE LA GARANTIE, UNE VIOLATION DU CONTRAT OU AUTRE. LA PRÉSENTE

GARANTIE REMPLACE TOUTE AUTRE GARANTIE, EXPRESSE OU IMPLICITE, Y COMPRIS TOUTE GARANTIE

DE QUALITÉ MARCHANDE, D’UTILITÉ À UNE FIN PARTICULIÈRE OU D’ABSENCE DE CONTREFAÇON.

UPC

126751

Garantie limitée à vie

Progress Lighting garantit à l’acheteur initial que les moteurs de ventilateur sont exempts de défauts électriques ou mécaniques

tant que l’acheteur initial est propriétaire du ventilateur. Les interrupteurs à chaînette, les interrupteurs inverseurs, les

condensateurs et les finis métalliques sont garantis contre les défauts de matériaux ou de fabrication pendant une période d’un

an à partir de la date d’achat. Le gauchissement des pales de bois ou de plastique n’est pas couvert par la présente garantie, ni la

corrosion ou la détérioration du fini des ventilateurs installés à moins de dix milles d’un bord de mer. Les garanties prolongées

pour les produits homologués ENERGY STAR® peuvent s’appliquer.

Lorsqu’ils sont installés correctement et dans des conditions d’utilisation normales, les ventilateurs de plafond Progress

Lighting dotés d’une source lumineuse à DEL intégrée sont garantis contre les défauts de matériaux et de fabrication causant le

non fonctionnement de la source lumineuse selon les spécifications pendant (i) cinq (5) ans à partir de la date d’achat des

modules d’éclairage à DEL et des composants électriques des ventilateurs pour les résidences unifamiliales et (ii) trois (3) ans à

partir de la date d’achat des modules d’éclairage à DEL et des composants électriques des ventilateurs pour les résidences

multifamiliales et pour les utilisations commerciales. Les ampoules à DEL fournies par Progress Lighting ne sont assorties

d’aucune autre garantie que celle du fabricant. Les ampoules autres qu’à DEL ne sont assorties d’aucune garantie.

En fournissant la preuve d’achat, l’acheteur initial peut retourner le ventilateur défectueux à son lieu d’achat pendant les 30

premiers jours afin qu’il soit remplacé. Après 30 jours, l’acheteur initial DOIT communiquer avec Progress Lighting au 864

678-1000 pour la réparation ou le remplacement du ventilateur, ce qui sera déterminé exclusivement par Progress Lighting et

constituera le seul et unique recours de l’acheteur.

Main-d’œuvre et expédition exclus. La présente garantie ne couvre par les coûts et les frais associés à la main-d’œuvre (y

compris, sans s’y limiter, les frais d’électricien) nécessaires à l’installation, au retrait ou au remplacement du ventilateur ou des

pièces du ventilateur.

La présente garantie ne s’applique pas en cas de perte ou de dommage découlant (i) de l’usure normale, de l’altération ou d’un

usage incorrect, abusif ou négligent ou (ii) d’une installation, d’une utilisation, d’une réparation ou d’un entretien inadéquats par

l’acheteur initial ou un tiers, y compris, sans s’y limiter, une tension électrique inadéquate ou une surtension, l’utilisation de

pièces ou d’accessoires inadéquats, une réparation non autorisée (effectuée ou tentée) ou l’omission d’entretenir le ventilateur.

LES GARANTIES QUI PRÉCÈDENT ÉNONCENT L’ENTIÈRE RESPONSABILITÉ DE PROGRESS LIGHTING AU

CHAPITRE DE LA GARANTIE AINSI QUE LE SEUL ET UNIQUE RECOURS DE L’ACHETEUR LIÉ À CES PRODUITS.

PROGRESS LIGHTING N’EST PAS RESPONSABLE DES DOMMAGES (Y COMPRIS LES DOMMAGES INDIRECTS,

SPÉCIAUX, ACCESSOIRES OU CONSÉCUTIFS) ATTRIBUABLES À LA DÉFECTUOSITÉ DU PRODUIT, QU’ILS

Certains États ne permettent pas de limitation à la durée implicite d’une garantie ou d’exclusion ou de limitation des dommages

accessoires ou consécutifs. Par conséquent, les limitations ci-dessus pourraient ne pas s’appliquer à vous. La présente garantie

vous accorde des droits précis et vous pourriez avoir d’autres droits qui peuvent varier d’un État à l’autre.

785247245437

785247245444

785247245420

Date d’achat

Magasin

Nº de modèle.

Nº de série .

Nº du fournisseur

Table des matières

Règles de sécurité.............................................................................................................................................................................1

Déballage de votre ventilateur ........................................................................................................................................................ 2

Installation de votre ventilateur ...................................................................................................................................................... 3

Installation de l’ensemble d’éclairage............................................................................................................................................. 8

Utilisation de votre émetteur .......................................................................................................................................................... 9

Entretien de votre ventilateur ........................................................................................................................................................11

Dépannage .....................................................................................................................................................................................12

Caractéristiques techniques ...........................................................................................................................................................13

1. Règles de sécurité

1. Afin de réduire les risques de choc électrique, vous assurer que l’électricité

a été coupée au disjoncteur ou à la boîte à fusibles avant de commencer.

2. Tout le câblage doit être conforme aux codes de l’électricité national et local.

L’installation électrique doit être effectuée par un électricien agréé qualifié.

3. AVERTISSEMENT: Afin de réduire les risques de choc électrique et

d’incendie, ne pas utiliser ce ventilateur avec un dispositif de contrôle de

la vitesse à semi-conducteur.

4. AVERTISSEMENT: Afin de réduire les risques d’incendie, de choc

électrique ou de blessure, installer à une boîte de sortie indiquée «

Acceptable pour support de ventilateur de 15,9 kg (35 lb) ou moins » et

utiliser les vis de montage fournies avec la boîte de sortie. La plupart des

boîtes de sortie couramment utilisées pour le support de luminaires ne sont

pas acceptables pour le support d’un ventilateur et doivent être remplacées.

Compte tenu de la complexité de l’installation de ce ventilateur, il est

fortement recommandé de faire appel à un électricien agréé qualifié.

ADVERTISSEMENT

AFIN DE RÉDUIRE LES RISQUES D’INCENDIE, DE CHOC ÉLECTRIQUE

OU DE BLESSURE, INSTALLER À UNE BOÎTE DE SORTIE INDIQUÉE «

ACCEPTABLE POUR SUPPORT DE VENTILATEUR.

5. La boîte de sortie et la structure de support doivent être solidement

installées et en mesure de supporter de manière fiable un poids de 15,9

kg (35 lb) ou moins.

6. Le ventilateur doit être installé en prévoyant un dégagement minimal de

2,1 m (7 pi) entre le bord de fuite des pales et le plancher.

7. Pour utiliser la fonction d’inversion du sens de rotation de ce ventilateur,

appuyer sur le bouton d’inversion pendant que le ventilateur fonctionne.

8. Éviter de placer des objets dans la trajectoire des pales.

9. Pour éviter les blessures ou les dommages au ventilateur ou à d’autres

articles, faire preuve de prudence lorsque vous travaillez à proximité du

ventilateur ou que vous le nettoyez.

10. Ne pas utiliser d’eau ou de détergent lorsque vous nettoyez le ventilateur

ou les pales du ventilateur. Un linge sec ou légèrement humide convient

la plupart du temps.

11. Une fois les branchements électriques réalisés, les conducteurs épissés

doivent être tournés vers le haut et poussés délicatement dans la boîte

de sortie. Les fils doivent être séparés et le conducteur mis à la terre

ainsi que le conducteur de mise à la terre de l’équipement doivent être

placés d’un côté de la boîte de sortie.

12. Les schémas électriques sont à titre de référence uniquement. Les

ensembles d’éclairage qui ne sont pas emballés avec le ventilateur

doivent être homologués cUL et porter une marque qui indique qu’ils

conviennent pour le modèle de ventilateur que vous installez. Les

interrupteurs doivent être homologués cUL pour usage général. Vous

reporter aux instructions qui accompagnent les ensembles d’éclairage

REMARQUE

LIRE ET CONSERVER TOUTES LES INSTRUCTIONS!

ADVERTISSEMENT

AFIN DE RÉDUIRE LE RISQUE DE BLESSURE, NE PAS PLIER LES BRAS DES

PALES (AUSSI APPELÉS SUPPORTS) PENDANT OU APRÈS L’INSTALLATION.

NE PAS INSÉRER D’OBJETS DANS LA TRAJECTOIRE DES PALES.

La page charge ...

Progress Lighting P250060-028-30 Mode d'emploi

Ce manuel convient également à

Progress Lighting P250060-028-30 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents