Weston 65-0601-W Mode d'emploi

Catégorie
Scelleuses sous vide
Taper
Mode d'emploi
VACUUM SEALER
65-0601-W
DUE TO CONSTANT FACTORY IMPROVEMENTS, THE PRODUCT PICTURED MIGHT DIFFER
SLIGHTLY FROM THE PRODUCT IN THIS BOX.
TABLE OF CONTENTS / ÍNDICE / TABLE DES MATIÈRES
2
3
4-5
6
6
7
7
7
7
8
8
9
10
11
12
13
14
15-16
17
18
19
20
22
24
26-27
28
28
29
29
29
29
30
30
31
32
33
34
35
36
37-38
39
40
41
42
44
46
48-49
50
50
51
51
51
51
52
52
53
54
55
56
57
58
59-60
61
62
63
64
67
IMPORTANT SAFEGUARDS
COMPONENT LIST
PROTECTIVE TAPE
COOLING FAN
VACUUM CHAMBER SEALS
LIMIT SWITCH
THERMAL OVERLOAD PROTECTOR
ASSEMBLY
OTHER CONSUMER SAFETY INFORMATION
CLEANING
CONTROL PANEL
USING THE ROLL HOLDER & CUTTER
INITIAL TESTING OF THE BAG SEAL
AUTOMATIC MODE OPERATION
MANUAL MODE OPERATION
MAINTENANCE KIT INSTRUCTIONS
TROUBLESHOOTING
REPLACING THE FUSE
STORAGE LIFESPAN GUIDELINES
VACUUM PACKAGING GUIDELINES
FOOD SAFETY
WARRANTY INFORMATION
NORMAS GENERALES DE SEGURIDAD
LISTA DE COMPONENTES
CINTA PROTECTORA
VENTILADOR DE REFRIGERACIÓN
SELLOS DE LA CÁMARA DE VACÍO
INTERRUPTOR DE LÍMITE
PROTECTOR DE SOBRECARGA TÉERMICA
ENSAMBLADO
OTRA INFORMACIÓN DE SEGURIDAD PARA EL CLIENTE
INSTRUCCIONES DE CUIDAD Y LIMPIEZA
PANEL DE CONTROL
UTILIZACIÓN DEL PORTAROLLOS Y EL CORTADOR
PRUEBA INICIAL DE SELLADO DE BOLSAS
OPERACIÓN EN MODO AUTOMÁTICO
FUNCIONAMIENTO EN MODO MANUAL
INSTRUCIONES DEL KIT DE MANTENIMIENTO
SOLUCIÓN DE PROBLEMAS
SUSTITUCIÓN DEL FUSIBLE
PAUTAS SOBRE LA VIDA EN ALMACENAMIENTO
LINEAMIENTOS PARA EMPACAR AL VACÍO
SEGURIDAD DE LOS ALIMENTOS
INFORMACIÓN DE GARANTÍA
IMPORTANTED RÈGLES DE SÉCURITÉ
DESCRIPTION DE LA PIÈCE
RUBAN PROTECTEUR
VENTILATEUR
JOINTS DE LA CHAMBRE SOUS VIDE
INTERRUPTEUR DE FIN DE COURSE
PROTECTION CONTRE LES SURCHARGES THERMIQUES
ASSEMBLY
AUTRES RENSEIGNEMENTS DE SÉCURITÉ AU CONSOMMATEUR
INSTRUCTIONS D’ENTRETIEN ET DE NETTOYAGE
PANNEAU DE COMMANDE
UTILISATION DU PORTE-ROULEAU ET DU COUPE-SAC
TEST INTIAL DU SCELLEMENT D’UN SAC
FONCTIONNEMENT EN MODE AUTOMATIQUE
FONCTIONNEMENT EN MODE MANUEL
DIRECTIVES POUR LA TROUSSE D’ENTRETIEN
DÉPANNAGE
REMPLACEMENT SU FUSIBLE
GUIDE DE CONSERVATION DES ALIMENTS EMBALLÉS
GUIDE D’EMBALLAGE SOUS VIDE
SÉCURITÉ ALIMENTAIRE
INFORMATION SUR LA GARANTIE
SAVE THESE INSTRUCTIONS
3
ENGLISH INSTRUCTIONS
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always
be followed to reduce the risk of re, electric shock, and/or injury to persons,
including the following:
1. Read all instructions.
2. ALWAYS DISCONNECT Vacuum
Sealer from power source before
servicing, changing accessories or
cleaning the unit.
3. Plug the Vacuum Sealer into a
standard 120 Volt, 60 Hz wall outlet.
Avoid using extension cords.
4. DO NOT USE the Vacuum Sealer
if the Power Cord, Plug or any other
parts are damaged. If the Power Cord
or the Vacuum Sealer is damaged,
call Customer Service. DO NOT
ATTEMPT TO REPLACE THE CORD.
Be sure to not allow the Power Cord to
drape into your work area. Check that
all parts are operating properly, and
perform the intended functions. Check
for any other conditions that may
affect the operation.
5. NEVER use any accessories or
parts from other manufacturers. Doing
so will VOID YOUR WARRANTY and
may cause re, electrical shock or
injury.
6. Reduce risk of unintentional
starting. Make sure the Power
Switch is in the “OFF” position before
attaching to the power source.
7. KEEP FINGERS CLEAR of the
Heat Sealing Bar and Seal Bar Tape
AT ALL TIMES, these areas become
HOT. Doing so may cause serious
injury.
8. DO NOT take this appliance
apart; doing so will VOID YOUR
WARRANTY and may result in
personal injury.
9. TO PROTECT AGAINST RISK
OF ELECTRICAL SHOCK: DO
NOT SUBMERGE THE VACUUM
SEALER INTO WATER OR LIQUID.
BE SURE THE VACUUM SEALER
IS DISCONNECTED FROM THE
POWER SOURCE BEFORE
CLEANING. Follow the “Cleaning
Instructions” in this booklet. NEVER
rinse appliance Vacuum Sealer under
tap.
10. NEVER LEAVE THE VACUUM
SEALER UNATTENDED. Be safe,
DISCONNECT the Vacuum Sealer
from power source before leaving
the work area. Close supervision is
necessary when any appliance is used
near children. This appliance is NOT to
be used by children.
11. DO NOT let the Power Cord hang
over edge of work surface.
12. Be sure the Vacuum Sealer is on
a stable work surface. Be sure all the
Vacuum Sealer Feet are stable.
13. DO NOT use the Vacuum Sealer
outdoors.
14. DO NOT use the Vacuum Sealer
while under the inuence of drugs,
medications or alcohol.
15. The Vacuum Sealer is ONLY
intended to be used with VACUUM
BAGS. For best results, only use the
recommended vacuum bags. DO
NOT USE HOUSEHOLD BAGS! Any
other uses of the Vacuum Sealer,
other than the uses described in this
booklet, could potentially damage the
appliance and void the warranty!
2
3
4
5
10
11
1
15
12
Vacuum Lid
16
Power
Panel
8
9
17
6
7
Upper
Housing
Lower
Housing
Vacuum
Chamber
I
O
13
14
ENGLISH INSTRUCTIONS
4
COMPONENT LIST
If any components of this unit are broken, the unit does not operate properly or you
need a replacement instruction manual, visit us on the web at
WestonSupply.com
Or call Weston Brands, LLC Toll Free at 1-800-814-4895
Monday thru Friday 8:00am-5:00pm ET. Outside the U.S. call 1-216-901-6801
DIAGRAM NUMBER PART DESCRIPTION PART NUMBER
1 HEATING ELEMENT 08-0627
2 SEAL BAR INSULATOR 08-0625
3 POWER CORD 08-0402
4 FUSE HOLDER 08-0604
5 8-AMP FUSE 08-0605
6 VACUUM PUMP 08-0639
7 TRANSFORMER 08-0641
8 FAN 08-0643
9 CIRCUIT BOARD 65-0638
10 SEAL BAR TAPE (BLACK) SEE MAINTENANCE
KIT
11 CHAMBER SEAL (2) SEE MAINTENANCE
KIT
12 VACUUM SEALER MAINTENANCE KIT: SEAL
BAR TAPE (BLACK), CHAMBER SEALS (2)
65-0701
13 ROLL HOLDER KIT INCLUDES: ROLL HOLDER,
ROD, ROD HOLDING ARMS (2), BRACKETS WITH
SCREWS (2 BRACKETS, 4 SCREWS)
65-0639
14 BLADE AND BAG CUTTER KIT INCLUDES:
BLADE, BLADE HOLDER
65-0640
15 BLADE 65-0641
16 CONTROL PANEL STICKER 65-0642
17 UPPER CHAMBER HOUSING 65-0643
ENGLISH INSTRUCTIONS
5
The Vacuum Sealer has an Internal Cooling Fan that runs whenever
the unit is plugged in and turned on. To save energy, turn the unit
“OFF” and unplug the Power Cord when not in use.
SEAL BAR TAPE
DO NOT
REMOVE!
The Seal Bar Heating Element is covered with Seal Bar Tape to
protect vacuum bags during sealing (Figure 1). DO NOT remove the
Seal Bar Tape. See the “Maintenance Kit” section of this manual for
information on replacing the Seal Bar Tape, if necessary.
OVAL VACUUM CHAMBER SEALS
DO NOT REMOVE!
BEFORE YOU START BAG SEALING
Before using the Vacuum Sealer, familiarize yourself with the bag sealing
functions. A vacuum bag is sealed when the Seal Bar Heating Element is
activated and heats the bag to its melting point, which then permanently
welds the bag layers together, sealing the bag shut. This appliance comes
pre-set from the factory to engage the Seal Bar Heating Element for 3
seconds. This is the correct amount of time required to fully seal Vacuum
Bags. Different brands of vacuum bags may require slightly more or slightly
less sealing time.
Test seal a couple of bags to be sure that the Seal Time is set properly. The
Seal Time may need to be increased (+) or decreased (-) to optimally seal a
bag.
ENGLISH INSTRUCTIONS
6
PROTECTIVE TAPE
There is one factory installed
strip of Seal Bar Tape on the Vacuum Sealer.
DO NOT REMOVE THE TAPE!
FIGURE 1
COOLING FAN
There are two factory-installed Oval Vacuum Chamber Seals on the Vacuum
Sealer. When the Vacuum Lid is closed and downward force applied, they
form an airtight seal so the Vacuum Chamber can be evacuated.
The Oval Vacuum Chamber Seals may wear over time and require
replacement. See the “Maintenance Kit” section of this manual for
information on replacing the Oval Vacuum Chamber Seals, if necessary.
THERMAL OVERLOAD PROTECTOR
The Vacuum Sealer will automatically shut down if it overheats. If this occurs,
turn the unit off and open the Vacuum Lid. Resume normal operation after
the unit cools or about 20 minutes.
To help prevent overheating, wait at least 20 seconds between cycles with the
Vacuum Lid open. Avoid touching the Seal Bar Tape. The Seal Bar Tape
will remain hot for a brief period of time after each sealing cycle.
LIMIT SWITCH
The Vacuum Sealer is equipped with a switch to prevent actuation of the Seal
Bar Heating Element in manual mode when the Vacuum Lid is open. When
the Vacuum Lid is closed, heat made by the Seal Bar Heating Element is
absorbed by the vacuum bag and Vacuum Lid Seal.
When the Vacuum Lid is open, there is no means to dissipate the heat and
unit damage may occur.
ASSEMBLY
Place the Vacuum Sealer on
a at, dry surface.
Plug the female end of the
Power Cord into the Power
Supply Port on the right side of
the appliance (Figure 2).
Plug the male end of the
Power Cord into a standard,
grounded 120-volt household
electrical outlet. DO NOT
attempt to modify the plug to t
into an unsuitable outlet.
FIGURE 2
I
O
NOTE: The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For
best results, only use the recommended vacuum bags with an embossed or mesh lining.
DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other than
the uses described in this booklet, could potentially damage the appliance and void the
warranty!
ENGLISH INSTRUCTIONS
7
VACUUM CHAMBER SEALS
· NEVER IMMERSE the Vacuum Sealer in water or other liquid.
· Make sure the Vacuum Sealer has completely cooled before cleaning it.
· Wipe clean all outside surfaces including the Plastic Vacuum Chamber and
Vacuum Lid with a damp cloth or paper towel. Most household spray cleaners
are safe to use. Avoid spraying directly into the vent on the left side of the
unit. DO NOT use abrasive cleansers!
· Be careful while cleaning not to peel or damage the strip of Seal Bar Tape
covering the Seal Bar Heating Element.
· Dry all surfaces and close the Vacuum Lid before storing the Vacuum
Sealer.
WARNING! Before cleaning, assembling or disassembling the
appliance, make sure the appliance is OFF and the PLUG IS REMOVED
FROM THE OUTLET/POWER SOURCE!
CLEANING INSTRUCTIONS
ENGLISH INSTRUCTIONS
8
Thermal Overload Protection
The vacuum sealer will automatically shut off if it overheats. If this occurs,
unplug the unit and open the vacuum lid. Resume normal operation after the
unit cools or about 20 minutes.
Always allow 20 seconds minimum for cool down between operations.
This allows the heat-seal bar to cool down.
Placing a new bag in the unit and closing the lid when the
heat-seal bar is still hot will cause the bag to prematurely melt together
before vacuum seal operation.
w CAUTION
Burn Hazard. Avoid touching the heat-seal bar.
Other Consumer Safety Information
w WARNING
Electrical Shock Hazard: This appliance is provided with a
grounded (3-prong) plug to reduce the risk of electric shock. The plug fits only
one way into a grounded outlet. Do not defeat the safety purpose of the plug
by modifying the plug in any way or by using an adapter. If the plug does not
fit fully into the outlet, reverse the plug. If it still does not fit, have an electrician
replace the outlet.
The length of the cord used on this appliance was selected to reduce the
hazards of becoming tangled in or tripping over a longer cord. If a longer cord
is necessary, an approved extension cord may be used. The electrical rating of
the extension cord must be equal to or greater than the rating of the appliance.
Care must be taken to arrange the extension cord so that it will not drape over
the countertop or tabletop where it can be pulled on by children or accidentally
tripped over.
· Start Button: The Start Button starts the 2-Piston Vacuum Pump, which
engages the air evacuation process.
· Cancel Button: This button is used to stop the vacuum cycle at any time.
· Seal Time + and - Buttons: The Seal Time Button adjusts the number of
seconds that the Sealing Bar will apply heat to create the bag’s seal. The
optimal time for different brands of bags can be adjusted using the Plus (+) or
Minus (-) Buttons. See the “Bag Sealing” section in this booklet for further
information on sealing vacuum bags.
· Seal Window: The numeric LED Seal Window indicates the number of
seconds that the Sealing Bar will be activated to apply heat to the bag that
creates the seal. Once the Seal Bar is activated, the display will countdown
to “0”. See the “Bag Sealing” section in this booklet for further information on
sealing vacuum bags.
· Vacuum Window: The numeric LED Vacuum Window indicates the level of
vacuum that the Vacuum Sealer has attained. The display will count up from
“0” to “9”.
·
Pulse Button: The pulse button is for sealing liquids or delicate items, lettnig
you control the vacuum process. When the bag is prepared, press the pulse
button as many times as necessary until you have eliminated the desired
amount of air. Press the manual seal button to seal the bag.
· Manual Bag Seal Button: This button will start the Seal Bar at any time in
Manual Mode. More information about the Manual Mode can be found in the
“Manual Mode” section of his booklet.
· Accessory Button: Press the Accessory Button when using vacuum
canisters (sold separately) to vacuum and seal items stored in a canister.
CONTROL PANEL
NOTE: The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For
best results, only use the recommended vacuum bags with an embossed or mesh lining.
DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other than
the uses described in this booklet, could potentially damage the appliance and void the
warranty!
ENGLISH INSTRUCTIONS
9
1. To create bags using the roll holder, remove the roll holder rod from the
cilps at the back of the vacuum sealer (FIGURE 6).
2. Slide the rod through the center opening of the roll (will hold bags up to
11” wide).
3. Fold the roll holder arms out and rest the rod in the slots on the roll holder
arms, carefully lining up the notches in the rod with the slots in the arms.
4. It is easier to cut bags from the roll when the bags are rolled over the roll
(as opposed to under the roll) (FIGURE 7).
5. Move the bag cutter towards the lid and pull the vacuum bag over the
cutter slot until you have reached the desired length.
6. Move the bag cutter back over the top of the bag roll, making sure the
blade is to one side.
7. Slide the blade across the bag roll to cut your roll into your custom bag
size (FIGURE 8).
USING THE ROLL HOLDER & CUTTER
FIGURE 6
P
O
W
E
R
I
N
D
I
C
ATO
R
O
N
O
F
F
8 A
M
P
F
U
S
E
O
N
LY
FIGURE 7
FIGURE 8
ENGLISH INSTRUCTIONS
10
1. ALWAYS allow the sealing bar to cool for approximately 20 seconds
between bags. Leave the Vacuum Lid OPEN between uses, this allows the
Heating Element to cool more quickly between bags.
2. Place one end of the bag onto the Sealing Bar, leaving about 2” (5 cm) of the
empty part of the bag beyond the inside edge of the Sealing Bar.
3. Be sure not to cover the Vacuum Port with the bag. Covering the Vacuum
Port prevents the proper vacuuming of air from the bag.
4. Close the Vacuum Lid while holding the bag in place. Press down on both
sides of the lid to lock the lid in place. You will hear each side “click” when it is
secured. NOTE: If both sides are NOT securely locked, the lid will NOT release
automatically. To resolve this issue, press down on both sides of the lid twice to
release the locks.
5. Press the Start Button engaging the Vacuum Pump (the Vacuum Pump must be
on for the Seal Bar to heat up).
6. Press the Manual Seal Button immediately after the Vacuum Pump starts.
(Press down on the Vacuum Lid to contact the Sealing Bar.)
7. After the Seal Window counts down to zero (0) the unit will automatically
release the vacuum and enable the Vacuum Lid to open.
8. Remove the bag and inspect the seal. The seal should appear smooth and
consistent all the way across the bag. The seal SHOULD NOT melt through
the bag at any point. Be sure there are no creases or wrinkles that may allow
air to leak into the bag. A properly sealed bag will not pull apart, the bag must
be cut open.
9. Do not form side seals on the bags, the sides are already sealed.
10. If the seal is good, proceed with vacuum packaging. Otherwise:
.
If the seal is melted through the bag trim off the bad seal with scissors and
adjust the Seal Time Down (-) in one second increments and try the test
process again.
.
If the seal has not fully welded the bag closed, trim off the bad seal with
scissors and adjust the Seal Time Up (+) in one second increments and try
the test process again.
INITIAL TESTING OF THE BAG SEAL
NOTE: The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For
best results, only use the recommended vacuum bags with an embossed or mesh lining.
DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other than
the uses described in this booklet, could potentially damage the appliance and void the
warranty!
WARNING! Before cleaning, assembling or disassembling the
appliance, make sure the appliance is OFF and the PLUG IS REMOVED
FROM THE OUTLET/POWER SOURCE!
ENGLISH INSTRUCTIONS
11
BEFORE ATTEMPTING VACUUM
PACKAGING BE SURE THAT THE
VACUUM SEALER IS SET UP IN
ACCORDANCE WITH ALL OF THE
SAFETY PRECAUTIONS LISTED IN
THIS BOOKLET.
1. Place the items to be vacuum
sealed into a vacuum bag. Allow at
least 2” (5 cm) at the open end of
the bag in order to create enough
seal space. Be sure not to cover the
Vacuum Port (FIGURE 9).
2. Close the Vacuum Lid while holding
the bag in place. Press down on both
sides of the lid to lock the lid in place.
You will hear each side “click” when it is
secured. NOTE: If both sides are NOT
securely locked, the lid will NOT release
automatically. To resolve this issue, press down on both sides of the lid twice to
release the locks.
3. Press and release the Start Button. The 2-Piston Vacuum Pump will begin
removing air from the bag while the LED Vacuum Window begins to count up.
You may need to apply light pressure to the Vacuum Lid during the count-
up process. The LED Vacuum Window will count up starting at the number
“1” and going thru to the number “9”, before automatically engaging the bag
sealing process. These numbers represent stages, not seconds.
4. Once the LED Vacuum Window displays the number “9”, the sealing
process will begin by counting down from your chosen setting to “0” on the
LED Seal Window.
5. Once the LED Seal Window has reached “0”, the Vacuum Sealer will
automatically stop the 2-Piston Vacuum Pump and release the vacuum
pressure moments later. DO NOT ATTEMPT TO PULL THE VACUUM LID
OPEN BEFORE THE VACUUM HAS BEEN RELEASED, SEVERE DAMAGE
TO THE SEALING BAR WILL RESULT.
AUTOMATIC MODE OPERATION
FIGURE 9
Leave 2”
Seal
Space
Vacuum Port
ENGLISH INSTRUCTIONS
12
BEFORE ATTEMPTING VACUUM
PACKAGING, BE SURE THAT THE
VACUUM SEALER IS SET UP IN
ACCORDANCE WITH ALL OF THE
SAFETY PRECAUTIONS LISTED IN THIS
BOOKLET.
1. Place the items to be vacuum sealed into
a vacuum bag. Allow at least 2” (5 cm) at
the open end of the bag in order to create
enough seal space. Be sure not to cover
the Vacuum Ports (Figure 10).
2. Close the Vacuum Lid while holding the bag
in place. Press down on both sides of the lid
to lock the lid in place. You will hear each side
“click” when it is secured. NOTE: If both sides
are NOT securely locked, the lid will NOT
release automatically. To resolve this issue,
press down on both sides of the lid twice to
release the locks.
3. While monitoring the vacuum bag, press and release START Button.
The 2-Piston Vacuum Pump will begin removing air from the bag. When
the desired level of air has been evacuated from the bag, press and
release the Manual Bag Seal Button. It will start the sealing bag process.
Note: You may need to apply light pressure to the Vacuum Lid during this
process.
Note: It requires some vacuum pressure in the bag to get good seal for the
bag.
4.Once the LED Seal Window has reached “0”, the Vacuum Sealer will
automatically stop the Vacuum Pump and release the vacuum pressure
moments later. DO NOT ATTEMPT TO PULL THE VACUUM LID OPEN
BEFORE THE VACUUM HAS BEEN RELEASED, SEVERE DAMAGE TO
THE SEALING BAR WILL RESULT.
FIGURE 10
Leave 2”
Seal
Space
Vacuum Port
NOTE: The Vacuum Sealer is ONLY intended to be used with VACUUM BAGS. For
best results, only use the recommended vacuum bags with an embossed or mesh lining.
DO NOT USE HOUSEHOLD BAGS! Any other uses of the Vacuum Sealer, other than
the uses described in this booklet, could potentially damage the appliance and void the
warranty!
WARNING! Before cleaning, assembling or disassembling the
appliance, make sure the appliance is OFF and the PLUG IS REMOVED
FROM THE OUTLET/POWER SOURCE!
ENGLISH INSTRUCTIONS
13
MANUAL MODE OPERATION
Some parts of the Vacuum Sealer may need replacing after repeated use. The
Vacuum Sealer Maintenance Kit will be necessary for the Vacuum Sealer to
properly function.
REPLACING THE OVAL VACUUM CHAMBER SEALS:
1. Turn “OFF” the Vacuum Sealer and remove the Power Cord from the electrical
outlet.
2. Make sure the unit is completely cool.
3. Open the Vacuum Lid.
4. Remove the Oval Vacuum Chamber Seal from the groove on the underside of
the Vacuum Lid.
5. Remove the Oval Vacuum Chamber Seal from the groove in the Plastic
Vacuum Chamber.
6. Set a new Oval Vacuum Chamber Seal on the groove in the Plastic Vacuum
Chamber. Work the seal into the groove with your ngers until done.
7. Position a new Oval Vacuum Chamber Seal into the groove in the Vacuum
Lid. Work the seal into the groove with your ngers until done.
REPLACING THE SEAL BAR TAPE:
1. Turn “OFF” the Vacuum Sealer and remove the Power Cord from the electrical
outlet.
2. Make sure the unit is completely cool.
3. Open the Vacuum Lid.
4. Pick at either end of the Seal Bar Tape covering the Seal Bar Heating Element
with a ngernail until it lifts slightly. Grasp the loose end and slowly pull
the Seal Bar Tape back over itself until fully removed.
5. Remove the backing from a new strip of Seal Bar Tape. Be careful not to
allow the Seal Bar Tape to contact anything including itself while the adhesive
side is exposed.
6. Hold one end of the Seal Bar Tape in each hand. Stick the left end of the Seal
Bar Tape to the at area on the Plastic Vacuum Chamber just left of the Seal
Bar Heating Element. Apply the Seal Bar Tape from left to right over the Seal
Bar Heating Element until done. Make sure there are no wrinkles or folds in the
Seal Bar Tape once applied. The Seal Bar Tape should fully cover the Seal Bar
Heating Element.
MAINTENANCE KIT INSTRUCTIONS
ENGLISH INSTRUCTIONS
14
TROUBLESHOOTING
Q: NOTHING HAPPENS WHEN THE POWER BUTTON IS PRESSED!
1. Make sure that the Power Cord is not
damaged in any way.
2. Be sure that the female end of the Power
Cord is plugged completely into the Power
Supply Port of the Vacuum Sealer, and that
the male end of the Power Cord is firmly
plugged into the wall outlet (Figure 11).
3. If the Vacuum Sealer is properly plugged
in, and the Power Button still does not work,
check the Fuse, located above the Power
Supply Port, on the right side of the Vacuum
Sealer. Twist the Fuse Holder off, then look
at the clear tube to see
if the Fuse is darkened. If the Fuse is
darkened, it will need to be replaced with a
standard 8-Amp Fuse.
4. If the Fuse does not need to be replaced, you will need to be sure the
electrical wall outlet is properly working. Plug in another appliance to see if
that appliance works from the wall outlet. USE ONLY TIME-DELAY FUSES.
Q: MY VACUUM SEALER SHUT OFF AND WILL NOT START AGAIN.
1. The Thermal Overload Protector may have been activated. In this
case, allow the Vacuum Sealer to cool by opening the Vacuum Lid for
approximately 20 minutes. Be sure to leave the Vacuum Lid open between
bag sealing.
2. Be sure that the female end of the Power Cord is plugged completely into
the Power Supply Port of the Vacuum Sealer, and that the male end of the
Power Cord is firmly plugged into the wall outlet.
3. If the Vacuum Sealer is properly plugged in, and the Power Button still
does not work, check the Fuse, located above the Power Supply Port, on
the right side of the Vacuum Sealer. Twist the Fuse Cap off, then look at the
clear tube to see if the Fuse is darkened. If the Fuse is darkened, it will need
to be replaced with a standard 8-Amp Fuse (Figure F).
4. If the Fuse does not need to be replaced, you will need to be sure the
electrical wall outlet is properly working. Plug in another appliance to see if
that appliance works from the wall outlet.
FIGURE 11
Check to see if the
Fuse is darkened.
I
O
ENGLISH INSTRUCTIONS
15
Q: THE BAG SEAL PULLS APART.
1. If the seal has not fully welded the bag closed, trim off the bad seal with
scissors and adjust the Seal Time Up (+) in one second increments and try the
test process again.
2. The Vacuum Sealer is only intended to be used with vacuum sealing
bags. For best results, Weston Vacuum Bags should be used. DO NOT USE
HOUSEHOLD BAGS with the Vacuum Sealer.
3. The seal of the bag may be incomplete. If the seal has a crease in it, or if
a liquid or powder has been trapped between the layers of the bag, the layers
may not have been welded together properly. Cut the seal off and wipe the
inside of the bag clean. Then, try to vacuum seal the package again. When
sealing a moist or powdery food, insert a paper towel into the bag above the
food before vacuum packaging. The paper towel will prevent the food from
interfering with the seal. See the “Vacuum Packaging Guidelines” in this
booklet for helpful tips.
FIGURE 12
Q: THE VACUUM PUMP STARTS, BUT NO AIR IS BEING
REMOVE FROM THE VACUUM BAG.
1. For the best results, always use
Weston brand vacuum bags.
2. Be sure that the bag is inserted
properly. Be sure not to cover the
Vacuum Port opening (Figure 12).
3. The bag may have a leak. If there
is a leak in the bag, air will be pulled
into the bag from the outside. Check
for tears or punctures. If you are
using a bag that was made from a roll
of material, double check that the seal
on the end of the bag is welded closed.
Q: THE SEALING BAR MELTS THROUGH THE BAG.
1. The Vacuum Sealer is only intended to be used with vacuum sealing
bags. For best results, Weston Vacuum Bags should be used. DO NOT USE
HOUSEHOLD BAGS with the Vacuum Sealer.
2. Check the condition of the Seal Bar Tape strips. Replace if needed.
3. Open the Vacuum Lid and allow the sealing bar to cool for 5-10 minutes.
Always leave the Vacuum Lid open between bags, and allow at least 20 seconds
between cycles.
4. The Sealing Bar time may need to be lowered. Adjust the Seal Time Down
(-) in one second increments and try the test process again. Refer to the “Initial
Testing of the Bag Seal” instructions in this booklet for more information.
Leave 2”
Seal
Space
ENGLISH INSTRUCTIONS
16
REPLACING THE FUSE
If the Vacuum Sealer does not operate when it is plugged
in and turned on, try any or all of the following:
1. Make sure the Fuse is not blown. The Fuse is located
on the right side of the unit directly above the Power
Cord Port. Turn “OFF” and unplug the Vacuum Sealer.
Twist off and remove the Fuse Holder. Remove and
check the Fuse. The thin metal band in the center of the
Fuse should be clean and unbroken. If it is burned and/or
broken, replace it with a new Fuse (8 Amp). Replace the
Fuse Holder.
2. Make sure the Connector at the end of the Power Cord
is plugged completely into the Power Cord Port.
3. Make sure the Power Cord is not damaged. DO
NOT use a damaged Power Cord. Call the Customer
Service line for information on part replacement.
4. Try connecting the Power Cord Plug to another
electrical outlet.
WARNING! Before cleaning, assembling or disassembling the Vacuum Sealer,
make sure the Vacuum Sealer is OFF and the PLUG IS REMOVED FROM THE
OUTLET/POWER SOURCE!
I
O
FIGURE 13
ENGLISH INSTRUCTIONS
17
. IMPORTANT NOTE: Vacuum packaging is NOT a substitute for refrigeration.
Vacuum packed perishable foods still require refrigeration.
. NEVER thaw frozen foods at room temperature. Thaw frozen foods in a
refrigerator or microwave oven.
. In general, the colder the temperature at which foods are stored, the longer the
shelf life.
. Handle vacuum sealer bags with care. Avoid damaging them. A damaged bag
will not hold a seal.
. Only use information in the following chart as a guideline! Refer to the “Vacuum
Packaging Guidelines” and “Food Safety” sections of this manual. Actual storage
life spans may vary. Check all food for spoilage before use.
STORAGE LIFESPAN GUIDELINES
FOOD STORAGE NORMAL VACUUM
TYPE LOCATION LIFE PACKED
LIFE
LARGE CUTS OF MEAT Freezer 6 months 2-3 years
GROUND MEAT Freezer 4 months 1 year
FISH Freezer 6 months 2 years
For best results, freeze meats & sh for 1-2 hours before vacuum packing to help prevent moisture
and juices from interfering with the seal of the vacuum bag.
COFFEE BEANS Room temperature 4 weeks 16 months
COFFEE BEANS Freezer 6-9 months 2-3 years
FLOUR, RICE, SUGAR Room Temperature 6 months 1-2 years
For best results, powder or grainy substances should be kept in their original container or bag, then placed in a
vacuum bag for sealing to prevent interfering with the seal of the vacuum bag.
BERRIES strawberries, raspberries, blackberries Refrigerator 1-3 days 1 week
BERRIES cranberries, huckleberries, blueberries Refrigerator 3-6 days 2 weeks
To prevent berries from being crushed by the vacuum sealer, it is best to freeze item before packing. Spread the berries out on a
cookie sheet to allow them to freeze individually. Berries frozen in a large block will be difcult to vacuum seal due to the
many small air pockets that would form between the berries.
CHEESE Refrigerator 1-2 weeks 4-8 months
If vacuum packed cheese is used often, make sure the vacuum bag is long enough to allow for repeated sealing. For shredded
cheese, place a paper towel inside the vacuum bag, on top of the cheese to prevent the cheese from being
sucked into the Vacuum Sealer or interfering with the sealing of the bag.
COOKIES, CRACKERS, BREADS with periodical opening Room Temperature 1-2 weeks 3-6 weeks
Freeze soft airy foods for 1-2 hours prior vacuum packing, to retain shape & texture.
PASTA, GRAINS, DRIED BEANS Room Temperature 6 months 1-1/2 years
NUTS Room Temperature 6 months 2 years
Dried foods with sharp edges should be wrapped in a paper towel or other matter to prevent the sharp edges from puncturing the vacuum bag.
LETTUCE Refrigerator 3-6 days 2 weeks
Wash & thoroughly dry leafy vegetables before vacuum packaging.
VEGETABLES Freezer 8 months 2 1/2 years
To maximize the taste of vegetables, blanch them before vacuum packaging. Blanching cooks the vegetables very briey, sealing
in the avor, color and texture, leaving the vegetables cooked but still crisp. Vegetables can be blanched in boiling water in the microwave,
most vegetables only require 2-3 minutes (corn on the cob requires 6-11 minutes). Then immerse the vegetables in cold water to
stop the cooking process. Dry the vegetables, then vacuum pack.
Table adapted from Dr. G.K.York, Dept. of Food Science & Tech, U of California, Davis.
ENGLISH INSTRUCTIONS
18
STORAGE LIFESPAN GUIDELINES
Powdery Items: When vacuum sealing powdery items, like our, it is best to keep
them in their original packaging before putting them into the vacuum bags.
Sharp or Pointed Items: When vacuum sealing sharp or pointy items, it is best
to cushion the edges so they do not puncture the bag during the vacuum process.
YEAST & BACTERIA
For best results in extending the life of foods, it is important to vacuum package
foods that are fresh. Once food has begun to deteriorate, vacuum packaging may
only slow the deterioration process. Vacuum sealing cannot completely prevent
the growth of mold. Other disease causing microorganisms can still grow in low
oxygen environments and may require further measures to be eliminated.
Yeast: The development of yeast can be slowed by refrigeration and completely
stopped by freezing food at 0
o
F (-18
o
C). Yeast causes fermentation, which will give
food an identiable smell.
Bacteria: Freezing cannot eliminate bacteria, but their growth can be stopped.
The growth of bacteria can be easily identied by an offensive odor and sometimes
a slimy texture. Some bacteria, like the one that causes botulism, can grow in low
oxygen environments and cannot be detected by smell, taste or color. Botulism is
very rare, but dangerous. Be sure that all foods are stored and cooked properly
before eating.
COOKING & HEATING
.
Before microwaving vacuum-packed foods, puncture or open the bag to allow
hot airto escape while heating.
.
Vacuum-packed foods can be thawed or cooked in boiling water.
.
Vacuum-packed perishable foods like meats, vegetables and cheeses must
be refrigerated (at or below 34
o
F (1.1
o
C)) or frozen, especially acid-free or
low-acid foods.
This is important because although vacuum packaging removes most air from
the bag, bacteria like Clostridium Botulinum, which produces a toxin that causes
the illness botulism, is anaerobic and grows in the absence of oxygen. Refrigeration
and freezing slow the growth of bacteria. It is also important to maintain a clean
working area to reduce the likelihood of packaging harmful bacteria with the food.
VACUUM PACKAGING GUIDELINES
ENGLISH INSTRUCTIONS
19
There are basic rules to follow when handling food.
They are COOK, SEPARATE, CLEAN, and CHILL.
COOK
It’s crucial to cook food to a safe internal temperature to destroy bacteria that is present.
The safety of hamburgers and other foods made with ground meat has been receiving a lot
of attention lately, and with good reason. When meat is ground, the bacteria present on the
surface is mixed throughout the ground mixture. If this ground meat is not cooked to at least
160
o
F to 165
o
F (71
o
C to 74
o
C), bacteria will not be destroyed and there’s a good chance you
will get sick.
Solid pieces of meat like steaks and chops don’t have dangerous bacteria like E. coli on the
inside, so they can be served more rare. Still, any beef cut should be cooked to an internal
temperature of at least 145
o
F (63
o
C) (medium rare). The safe temperature for poultry is 165
o
F
(75
o
C) and solid cuts of pork should be cooked to 145
o
F (63
o
C).
SEPARATE
Foods that will be eaten uncooked and foods that will be cooked before eating MUST
ALWAYS be separated. Cross-contamination occurs when raw meats or eggs come in
contact with foods that will be eaten uncooked. This is a major source of food poisoning.
Always double-wrap raw meats and place them on the lowest shelf in the refrigerator so
there is no way juices can drip onto fresh produce. Then use the raw meats within 1-2 days
of purchase, or freeze for longer storage. Defrost frozen meats in the refrigerator, not on the
counter.
When grilling or cooking raw meats or sh, make sure to place the cooked meat on a clean
platter. Don’t use the same platter you used to carry the food out to the grill. Wash the utensils
used in grilling after the food is turned for the last time on the grill, as well as spatulas and
spoons used for stir-frying or turning meat as it cooks.
Make sure to wash your hands after handling raw meats or raw eggs. Washing hands with
soap and water, or using a pre-moistened antibacterial towelette is absolutely necessary after
you have touched raw meat or raw eggs. Not washing hands and surfaces while cooking is a
major cause of cross-contamination.
CLEAN
Wash your hands and work surfaces frequently when you are cooking. Washing with soap
and warm water for at least 15 seconds, then dry with a paper towel.
CHILL
Chilling food is very important. The danger zone where bacteria multiply is between 40
o
F and
140
o
F (4
o
C and 6
o
C). Your refrigerator should be set to 40
o
F (4
o
C) or below; your freezer should
be 0
o
F (-17
o
C) or below. Simple rule: serve hot foods hot, cold foods cold. Use chang dishes
or hot plates to keep food hot while serving. Use ice water baths to keep cold foods cold. Never
let any food sit at room temperature for more than 2 hours - 1 hour if the ambient temperature
is 90
o
F (32
o
C) or above. When packing for a picnic, make sure the foods are already chilled
when they go into the insulated hamper. The hamper won’t chill food - it just keeps food cold
when properly packed with ice. Hot cooked foods should be placed in shallow containers and
immediately refrigerated so they cool rapidly. Make sure to cover foods after they are cool.
NOTE: Special considerations must be made when using venison or other wild game, since it
can become heavily contaminated during eld dressing. Venison is often held at temperatures
that could potentially allow bacteria to grow, such as when it is being transported. Refer to
the USDA Meat and Poultry Department for further questions or information on meat and
food safety.
FOOD SAFETY
20
ENGLISH INSTRUCTIONS
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Weston 65-0601-W Mode d'emploi

Catégorie
Scelleuses sous vide
Taper
Mode d'emploi