Dremel 100 Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur

Ce manuel convient également à

IMPORTANT: IMPORTANT : IMPORTANTE:
Read Before Using Lire avant usage Leer antes de usar
For English Version Version française Versión en español
See page 2 Voir page 23 Ver la página 45
Operating/Safety Instructions
Consignes de fonctionnement/curi
Instrucciones de funcionamiento y seguridad
1-800-4-DREMEL (1-800-437-3635) www.dremel.com
Call Toll Free for
Consumer Information
& Service Locations
Pour obtenir des informations
et les adresses de nos centres
de service après-vente,
appelez ce numéro gratuit
Llame gratis para
obtener información
para el consumidor y
ubicaciones de servicio
P.O. Box 081126 Racine, WI 53408-1126
R
4000
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 1
2
Work area safety
Keep work area clean and well lit. Cluttered
or dark areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust
or fumes.
Keep children and bystanders away while
operating a power tool. Distractions can
cause you to lose control.
Electrical safety
Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric
shock.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk
of electric shock if your body is earthed or
grounded.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
When operating a power tool outdoors,
use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
IIf operating a power tool in a damp location
is unavoidable, use a Ground Fault Circuit
Interrupter (GFCI) protected supply. Use of
an GFCI reduces the risk of electric shock.
Personal safety
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention
while operating power tools may result in
serious personal injury.
Use personal protective equipment. Always
wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the
switch is in the off-position before
connecting to power source and / or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
switch or energizing power tools that have the
switch on invites accidents.
Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power
tool may result in personal injury.
Do not overreach. Keep proper footing and
balance at all times. This enables better
control of the power tool in unexpected
situations.
Dress properly. Do not wear loose clothing
or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewelry or long hair can be caught in
moving parts.
If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
Power tool use and care
Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is
dangerous and must be repaired.
Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
!
WARNING
General Power Tool Safety Warnings
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 2
3
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment
or binding of moving parts, breakage of
parts and any other condition that may
affect the power tool’s operation. If damaged,
have the power tool repaired before use.
Many accidents are caused by poorly
maintained power tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool
bits etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified
repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Hold power tool by insulated gripping
surfaces, because the cutter may contact
its own cord. Cutting a ”live” wire may make
exposed metal parts of the power tool ”live”
and shock the operator.
Use clamps or another practical way to
secure and support the workpiece to a
stable platform. Holding the work by your
hand or against the body leaves it unstable
and may lead to loss of control.
Accessories must be rated for at least the
speed recommended on the tool warning
label. Wheels and other accessories running
over rated speed can fly apart and cause
injury.
If cutting into existing walls or other blind
areas where electrical wiring may exist is
unavoidable, disconnect all fuses or circuit
breakers feeding this worksite.
Do not operate the flexible shaft with a
sharp bend. Over bending the shaft can
generate excessive heat on the jacket or hand
piece. The recommended minimum is 5"
radius.
Always disconnect the power cord from
the power source before making any
adjustments or attaching any accessories.
You may unexpectedly cause the tool to start
leading to serious personal injury.
Be aware of the switch location, when
placing the tool down or when picking the
tool up. You may accidentally activate the
switch.
Always hold the hand piece firmly in your
hands during the start-up. The reaction
torque of the motor, as it accelerates to full
speed, can cause the shaft to twist.
Always wear safety goggles and dust
mask. Use only in well ventilated area.
Using personal safety devices and working in
safe environment reduces risk of injury.
After changing the bits or making any
adjustments, make sure the collet nut and
the EZ TWIST
integrated wrench/nose
cap are both securely tightened. Loose
adjustment devices can unexpectedly shift,
causing loss of control, loose rotating
components will be violently thrown.
Do not reach in the area of the spinning
bit. The proximity of the spinning bit to your
hand may not always be obvious.
Allow brushes to run at opera ting speed
for at least one minute before using wheel.
During this time no one is to stand in front
or in line with the brush. Loose bristles or
wires will be discharged during the run-in time.
Wire and bristle brushes must never be
operated at speeds greater than
Safety Rules for Rotary Tools
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 3
4
15,000/min. Direct the discharge of the
spinning wire brush away from you. Small
particles and tiny wire fragments may be
discharged at high velocity during the
“cleaning” action with these brushes and may
become imbedded in your skin. Bristles or
wires will be discharged from the brush at high
speeds.
Wear protective gloves and face shield
with wire or bristle brushes. Apply wire or
bristle brushes lightly to the work as only
the tips of the wire/bristles do the work.
“Heavy pressure on bristles will cause the
wire or bristle to become overstressed,
resulting in a wiping action and will cause the
bristles/wire to be discharged.
Carefully handle both the tool and
individual grinding wheels to avoid
chipping or cracking. Install a new wheel if
tool is dropped while grinding. Do not use
a wheel that may be damaged. Fragments
from a wheel that bursts during operation will
fly away at great velocity possibly striking you
or bystanders.
Never use dull or damaged bits. Sharp bits
must be handled with care. Damaged bits
can snap during use. Dull bits require more
force to push the tool, possibly causing the bit
to break.
Use clamps to support workpiece
whenever practical. Never hold a small
workpiece in one hand and the tool in the
other hand while in use. Allow for
sufficient space, at least 6", between your
hand and the spinning bit. Round material
such as dowel rods, pipes or tubing have a
tendency to roll while being cut, and may
cause the bit to bite or jump toward you.
Clamping a small workpiece allows you to use
both hands to control the tool.
Inspect your workpiece before cutting.
When cutting irregularly shaped
workpieces, plan your work so it will not
slip and pinch the bit and be torn from
your hand. For example, if carving wood,
make sure there are no nails or foreign objects
in the workpiece. Nails or foreign objects can
cause the bit to jump.
Never start the tool when the bit is
engaged in the material. The bit cutting
edge may grab the material causing loss of
control of the cutter.
Avoid bouncing and snagging the wheel,
especially when working corners, sharp
edges etc. This can cause loss of control and
kick-back.
The direction of feed with the bit into the
material when carving, routing or cutting is
very important. Always feed the bit into
the material in the same direction as the
cutting edge is exiting from the material
(which is the same direction as the chips
are thrown). Feeding the tool in the wrong
direction, causes the cutting edge of the bit to
climb out of the work and pull the tool in the
direction of this feed.
If the workpiece or bit becomes jammed or
bogged down, turn the tool “OFF” by the
switch. Wait for all moving parts to stop
and unplug the tool, then work to free the
jammed material. If the switch to the tool is
left “ON” the tool could restart unexpectedly
causing serious personal injury.
Do not leave a running tool unattended,
turn power off. Only when tool comes to a
complete stop is it safe to put it down.
Do not grind or sand near flammable
materials. Sparks from the wheel could ignite
these materials.
Do not touch the bit or collet after use.
After use the bit and collet are too hot to be
touched by bare hands.
Regularly clean the tool's air vents by
compressed air. Excessive accumulation of
powdered metal inside the motor housing may
cause electrical failures.
Do not allow familiarity gained from
frequent use of your rotary tool to become
commonplace. Always remember that a
careless fraction of a second is sufficient to
inflict severe injury.
Do not alter or misuse tool. Any alteration or
modification is a misuse and may result in
serious personal injury.
This product is not intended for use as a
dental drill, in human or veterinary medical
applications. Serious personal injury may
result.
When using the steel saws, cut off wheels,
high speed cutters or tungsten carbide
cutters, always have the work secure ly
clamped. Never attempt to hold the work
Safety Rules for Rotary Tools - (cont.)
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 4
5
Additional Safety Warnings
GFCI and personal protection devices like
electrician’s rubber gloves and footwear will
further enhance your personal safety.
Do not use AC only rated tools with a DC
power supply. While the tool may appear to
work, the electrical components of the AC
rated tool are likely to fail and create a hazard
to the operator.
Keep handles dry, clean and free from oil
and grease. Slippery hands cannot safely
control the power tool.
Use clamps or other practical way to secure
and support the workpiece to a stable
platform. Holding the work by hand or against
your body is unstable and may lead to loss of
control.
Develop a periodic maintenance schedule
for your tool. When cleaning a tool be
careful not to disassemble any portion of
the tool since internal wires may be
misplaced or pinched or safety guard return
springs may be improperly mounted.
Certain cleaning agents such as gasoline,
carbon tetrachloride, ammonia, etc. may
damage plastic parts.
Risk of injury to user. The power cord must only
be serviced by a Dremel Service Facility..
Some dust created by power
sanding, sawing, grinding,
drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemically-
treated lumber.
Your risk from these exposures varies,
depending on how often you do this type of
work. To reduce your exposure to these
chemicals: work in a well ventilated area, and
work with approved safety equipment, such as
those dust masks that are specially designed
to filter out microscopic particles.
!
WARNING
Safety Rules for Rotary Tools - (cont.)
with one hand while using any of these
accessories. The reason is that these wheels
will grab if they become slight ly canted in the
groove, and can kick back causing loss of
control resulting in serious in jury. Your second
hand should be used to steady and guide the
hand holding the tool. When a cutoff wheel
grabs, the wheel itself usually breaks. When
the steel saw, high speed cutters or tungsten
carbide cutter grab, it may jump from the
groove and you could lose control of the tool.
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 5
6
IMPORTANT: Some of the following symbols may be used on your tool. Please study them
and learn their meaning. Proper interpretation of these symbols will allow you to operate the
tool better and safer.
Symbol Name Designation/Explanation
V Volts Voltage (potential)
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
kg Kilograms Weight
min Minutes Time
s Seconds Time
Diameter Size of drill bits, grinding wheels, etc.
n
0
No load speed Rotational speed, at no load
n Rated speed Maximum attainable speed
.../min Revolutions or reciprocation Revolutions, strokes, surface speed,
per minute orbits etc. per minute
0 Off position Zero speed, zero torque...
1, 2, 3, ... Selector settings Speed, torque or position settings.
I, II, III, Higher number means greater speed
Infinitely variable selector with off Speed is increasing from 0 setting
Arrow Action in the direction of arrow
Alternating current Type or a characteristic of current
Direct current Type or a characteristic of current
Alternating or direct current Type or a characteristic of current
Class II construction Designates Double Insulated
Construction tools.
Earthing terminal Grounding terminal
Warning symbol Alerts user to warning messages
Li-ion RBRC seal Designates Li-ion battery recycling
program
Ni-Cad RBRC seal Designates Ni-Cad battery recycling
program
Read manual symbol Alerts user to read manual
Wear eye protection symbol Alerts user to wear eye protection
Symbols
0
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 6
7
This symbol designates that this tool is listed by Underwriters Laboratories.
This symbol designates that this tool is listed by the Canadian Standards
Association.
This symbol designates that this tool is listed by the Canadian Standards
Association, to United States and Canadian Standards.
This symbol designates that this tool complies to NOM Mexican Standards.
This symbol designates that this tool is listed by the Intertek Testing
Services, to United States and Canadian Standards.
Symbols (continued)
IMPORTANT: Some of the following symbols may be used on your tool. Please study them
and learn their meaning. Proper interpretation of these symbols will allow you to operate the
tool better and safer.
This symbol designates that this component is recognized by Underwriters
Laboratories.
This symbol designates that this tool is listed by Underwriters Laboratories,
to United States and Canadian Standards.
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 7
8
Disconnect the plug from the power source before making any
assembly, adjustments or changing accessories. Such preventive safety
measures reduce the risk of starting the tool accidentally.
!
WARNING
Model number 4000
Voltage rating 120V 50 - 60Hz
Amperage rating 1.6A
No load speed n
0
5,000-35,000/min
Collet capacities 1/32, 1/16", 3/32", 1/8"
Functional Description and Specifications
Model 4000 High Speed Rotary Tool
R
COLLET
WRENCH
ON/OFF
SWITCH
SHAFT LOCK
BUTTON
EZ TWIST™
INTEGRATED
WRENCH/NOSE CAP
CORD
BRUSH COVER
(one on each side)
VARIABLE SPEED
DIAL
VENTILATION
OPENINGS
VENTILATION
OPENINGS
HANGER
COLLET
NUT
COLLET
SHAFT
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 8
9
COLLETS Four different size collets (see
illus tration), to accommodate different shank
sizes, are avail able for your Rotary Tool. To
install a different collet, remove the collet nut
and remove the old collet. Insert the unslotted
end of the collet in the hole in the end of the
tool shaft. Replace collet nut on the shaft.
Always use the collet which
matches the shank size of
the accessory you plan to use. Never force a
larger diameter shank into a collet.
Note: Most rotary tool kits do not include all
four collets sizes.
BALANCING ACCESSORIES For precision
work, it is important that all accessories be in
Always unplug Rotary Tool before changing accessories, changing collets
or servicing your Rotary Tool.
COLLET NUT To loosen, first press shaft
lock button and rotate the shaft by hand until the
lock engages the shaft preventing further
rotation. Your Dremel 4000 is equipped with a
quick collet lock mechanism. This mechanism
engages the output shaft in 8 separate locations
on the shaft for easier operation.
Do not engage lock while
the Rotary Tool is running.
With the shaft lock engaged use the collet
wrench to loosen the collet nut if necessary. The
collet nut must be loosely threaded on when
inserting an accessory. Change accessories by
inserting the new one into the collet as far as
possible to minimize runout and unbalance.
With the shaft lock engaged, finger tighten the
collet nut until the accessory shank is gripped by
the collet. Avoid excessive tightening of the
collet nut when there is no bit inserted.
EZ TWIST INTEGRATED
WRENCH/NOSE CAP
The nose cap of your tool has an integrated
wrench allowing you to loosen and tighten the
collet nut without the use of the standard collet
wrench. Unscrew the nose cap from the tool,
line-up steel insert on inside of cap with collet
nut. With the shaft lock engaged twist nose cap
clockwise to tighten, and counter-clockwise to
loosen.
!
WARNING
Assembly
COLLET IDENTIFICATION CHART
Collet sizes can be identified by the rings
on the back end of collet.
1/32" Collet has one (1) ring.
1/16" Collet has two (2) rings.
3/32" Collet has three (3) rings.
1/8" Collet has no rings. (Included in
most tool kits on the tool)
COLLET
NUT
IDENTIFICATION
RINGS
480
1/8"
COLLET
481
3/32"
COLLET
482
1/16"
COLLET
483
1/32"
COLLET
!
CAUTION
COLLET
NUT
TO
LOOSEN
TO
TIGHTEN
COLLET
WRENCH
SHAFT LOCK
BUTTON
COLLET
NUT
TO
LOOSEN
TO
TIGHTEN
SHAFT LOCK
BUTTON
!
CAUTION
EZ TWIST™
INTEGRATED
WRENCH/NOSE CAP
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 9
10
Operating Instructions
Dremel 4000
Thank you for purchasing the Dremel 4000.
This product was designed by the many
Dremel users who passionately use their rotary
tools daily. This tool was designed to give you
the ultimate performance when working on
projects.
The Dremel 4000 is the MOST versatile rotary
tool available today. It has a wide speed range
including a high performance motor with
electronic feedback that allows the tool to
maintain its speed under load. The design of
the tool is symmetrical and contains plenty of
soft grip so the tool can be held comfortably in
many positions. The quick collet lock
mechanism makes locking the output shaft
easier for changing accessories. You will
appreciate the many applications that the
Dremel 4000 can easily tackle.
Rotary Tool Introduction
The Rotary Tool has a small, powerful electric
universal motor, is comfort able in the hand, and
is made to accept a large variety of accessories
including abrasive wheels, drill bits, wire
brushes, polishers, engraving cutters, router
bits, cutting wheels and attachments.
Accessories come in a variety of shapes and
permit you to do a number of different jobs. As
you be come familiar with the range of
accessories and their uses, you will learn just
how versatile the Rotary Tool is. You’ll see
dozens of uses you hadn’t thought of before.
The real secret of the Rotary Tool is its speed.
To understand the advantages of its high
speed, you have to know that the standard
portable electric drill runs at speeds up to 2,800
revolutions per minute. The Rotary Tool
operates at speeds up to 35,000 revolutions
per minute. The typical electric drill is a low-
speed, high torque tool; the Rotary Tool is just
the opposite a high-speed, low torque tool.
The major difference to the user is that in the
high speed tools, the speed combined with the
acces sory mounted in the collet does the work.
You don’t apply pressure to the tool, but simply
hold and guide it. In the low speed tools, you
not only guide the tool, but also apply pressure
to it, as you do, for example, when drilling a hole.
It is this high speed, along with its compact size
and wide variety of special accessories and
attachments, that makes the Rotary Tool differ -
ent from other tools. The speed enables it to do
jobs low speed tools cannot do, such as cutting
hardened steel, en graving glass, etc.
Getting the most out of your Rotary Tool is a
matter of learning how to let this speed work for
you. To learn about more uses and the
versatility of Dremel accessories and
attachments refer to this Owner's Manual or
check our website at www.Dremel.com.
Using the Rotary Tool
The first step in learning to use the Rotary Tool
is to get the “feel” of it. Hold it in your hand and
feel its weight and balance. Feel the taper of
the housing. This taper permits the Rotary Tool
to be grasped much like a pen or pencil
(Figure A).
Always hold the tool away from your face.
Accessories can be damaged during handling,
and can fly apart as they come up to speed.
This is not common, but it does happen.
Practice on scrap materials first to see how the
Rotary Tool's high speed action performs. Keep
in mind that the work is done by the speed of
the tool and by the accessory in the collet. You
should not lean on or push the tool during use.
Instead, lower the spinning accessory lightly to
the work and allow it to touch the point at which
you want cutting (or sanding or etching, etc.) to
begin. Con centrate on guiding the tool over the
work using very little pressure from your hand.
Allow the accessory to do the work.
Usually, it is best to make a series of passes
with the tool rather than attempt to do all the
work in one pass. To make a cut, for example,
good balance (much the same as the tires on
your automobile). To true up or balance an
accessory, slightly loosen collet nut and give
the accessory or collet a 1/4 turn. Re tighten
collet nut and run the Rotary Tool. You should
be able to tell by the sound and feel if your
accessory is running in balance. Continue
adjusting in this fashion until best balance is
achieved. To maintain balance on abrasive
wheel points, before each use, with the wheel
point secured in the collet, turn on the Rotary
Tool and run the 415 Dressing Stone lightly
against the revolving wheel point. This removes
high spots and trues up the wheel point for
good balance.
The hanger is provided for the use of hanging
your tool while using the flex-shaft or for
storage. If you do not use the hanger, snap it
back into place so it will be out of the way while
the tool is in use.
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 10
11
To select the right speed for each job, use a
practice piece of material.
NOTE: Speed is affected by voltage
changes. A reduced incoming voltage will
slow the RPM of the tool.
SLIDE "ON/OFF" SWITCH
The tool is switched "ON" by the slide switch
located on the topside of the motor housing.
TO TURN THE TOOL "ON", slide the switch
button forward.
TO TURN THE TOOL "OFF", slide the switch
button backward.
HIGH PERFORMANCE MOTOR
Your tool is equipped with a high performance
rotary tool motor. This motor expands the
versatility of the rotary tool by driving additional
attachments such as the Dremel Multi-Saw
and Dremel Planer.
ELECTRONIC FEEDBACK
Your tool is equipped with an internal electronic
feedback system that provides a “soft start”,
which will reduce the stresses that occur from
a high torque start. The system also helps to
keep the preselected speed virtually constant
between no-load and load conditions.
VARIABLE SPEED DIAL
Your tool is equipped with a variable speed
dial. The speed may be adjusted during
operation by presetting the dial on or
between any one of the settings.
You can refer to the charts on page 19, 20,
21 and 22 to determine the proper speed,
based on the materi al being worked and
WARNING
Wear Eye Protection
Whenever you hold the tool, be careful not to
cover the air vents with your hand. This blocks the
air flow and causes the motor to overheat.
CAUTION
!
Operating Speeds
For best control in close work, grip the
Rotary Tool like a pencil between your
thumb and forefinger.
The “Golf Grip” method of holding the
tool is used for more aggressive
operations such as grinding a flat surface
or using cutoff wheels.
R
R
Questions or Problems? Call 1-800-437-3635
or check our website at www.Dremel.com
FIG. A FIG. B
For performing precision tasks a separate nose piece is available in some
kits. It has a tapered shape which allows the user to pinch the nose piece
comfortably between thumb and forefinger. It provides an excellent line of
sight for performing detailed etching, carving and engraving work.
pass the tool back and forth over the work,
much as you would a small paint brush. Cut a
little material on each pass until you reach the
desired depth. For most work, the gentle touch
is best. With it, you have the best control, are
less likely to make errors, and will get the
most effi cient work out of the accessory.
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 11
12
the type of accessory being used. These
charts enable you to select both the
correct acces sory and the optimum speed
at a glance.
The speed of Rotary Tool is controlled by
setting this dial on the housing.
Settings for Approximate Revolutions.
Switch Setting Speed Range
5 15,000-7,000 RPM
*10 17,000-10,000 RPM
15 13,000-17,000 RPM
20 18,000-23,000 RPM
25 23,000-27,000 RPM
30 28,000-32,000 RPM
35 33,000-35,000 RPM
* Wire Brush Setting.
Needs for Slower Speeds
Certain materials, however, (some plastics and
precious metals, for ex ample) require a
relatively slow speed because at high speed
the friction of the accessory generates heat
and may cause damage to the material.
Slow speeds (15,000 RPM or less) usually are
best for polishing operations employing the felt
polishing ac ces sories. They may also be best
for working on deli cate projects as “eggery
work, delicate wood carving and fragile model
parts. (All brushing applications require lower
speeds to avoid wire discharge from the
holder.)
Higher speeds are better for carving, cutting,
routing, shaping, cutting dadoes or rabbets in
wood.
Hardwoods, metals and glass require high
speed operation, and drilling should also be
done at high speeds.
The point to remember is this: Many
applications and accessories in our line will
provide the best performance at full speed, but
for certain materials, applications, and
accessories, you need slower speeds, which is
the reason our variable speed models are
available.
To aid you in determining the optimum
operational speed for differ ent materials and
different accessories, we have construct ed a
series of tables that appear on page 19, 20, 21
and 22. By referring to these tables, you can
discover the recommended speeds for each
type of accessory. Look these tables over and
become familiar with them.
Ultimately, the best way to determine the
correct speed for work on any material is to
practice for a few minutes on a piece of scrap,
even after referring to the chart. You can
quickly learn that a slower or faster speed is
more effective just by observing what hap pens
as you make a pass or two at different speeds.
When working with plastic, for example, start at
a slow rate of speed and increase the speed
until you observe that the plastic is melting at
the point of contact. Then reduce the speed
slight ly to get the optimum working speed.
Some rules of thumb in regard to speed:
1. Plastic and other materials that melt at low
temperatures should be cut at low speeds.
2. Polishing, buffing and cleaning with any
type of bristle brush must be done at
speeds not greater than 15,000 RPM to
prevent damage to the brush.
3. Wood should be cut at high speed.
4. Iron or steel should be cut at high speed. If
a high speed steel cutter starts to chatter
this normally means it is running too slow.
5. Aluminum, copper alloys, lead alloys, zinc
alloys and tin may be cut at various speeds,
depending on the type of cutting being
done. Use paraffin or other suitable
lubricant on the cutter to prevent the cut
material from adhering to the cutter teeth.
Increasing the pressure on the tool is not the
answer when it is not performing as you think it
should. Perhaps you should be using a
different accessory, and perhaps an
adjustment in speed would solve the problem.
Leaning on the tool does not help.
Let speed do the work!
Use only Dremel
®
, high-performance accessories.
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 12
13
Maintenance Information
Service
Preventive maintenance
pe r formed by unauthorized
per so n nel may result in misplacing of
internal wires and components which could
cause serious hazard. We recommend that
all tool service be performed by a Dremel
Service Facility.
To avoid injury from
unexpected starting or
electrical shock, always remove plug from
wall outlet before performing service or
cleaning.
CARBON BRUSHES
The brushes and commutator in your tool have
been engineered for many hours of
dependable service.
In order to prepare your brushes for use, run
your tool at full speed for 5 minutes under no
load. This will properly “seat” your brushes,
which extends the life of both your brushes
and your tool.
To maintain peak efficiency of the motor, we
recommend every 40 - 50 hours the brush es
be examined. Only genuine Dremel replace -
ment brushes specially designed for your tool
should be used.
MAINTENANCE OF REPLACEABLE
BRUSHES ON MODEL 4000
The brushes should be inspected frequently
when tools are used continuously. If your tool
runs spo rad ically, loses power, makes unusual
noises or runs at a reduced speed, check the
brushes.
To continue using the tool
in this condition will
permanently damage your tool.
Follow these steps to check/change the rotary
tool brushes:
1. With the power cord unplugged, place the
tool on a clean surface. Use the tool
wrench as a screwdriver to remove the
brush caps in a counter-clockwise direction
(Figure C).
2. Remove the brushes from the tool by
pulling on the spring that is attached to the
carbon brush. If the brush is less than 1/8"
long and the end surface of the brush that
contacts the commutator is rough and/or
pitted, they should be replaced. Check both
brushes (Figure D).
Usually the brushes will not wear out simul -
taneously. If one brush is worn out, replace
both brushes. Make sure the brushes are
installed as illus trated. The curved surface of
the brush must match the curvature of the
commutator. Also check that the brush caps sit
flush with the tool housing.
3. After replacing brushes the tool should be
run at no-load; place it on a clean surface
and run it freely at full speed for 5 minutes
before loading (or using) the tool. This will
allow the brushes to “seat” properly and will
give you more hours of life from each set of
brushes. This will also extend the total life of
your tool since the com mutator surface will
“wear” longer.
CAUTION
!
WARNING
!
!
WARNING
R
FIG. C
R
BRUSH
BRUSH SPRING
BRUSH CAP
CURVED END OF
BRUSH MUST
MATCH
CURVATURE OF
COMMUTATOR
FIG. D
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 13
14
Extension Cords
If an extension cord is necessary, a cord
with adequate size conductors that is
capable of carrying the current necessary
for your tool must be used. This will prevent
excessive voltage drop, loss of power or
overheating. Grounded tools must use 3-wire
extension cords that have 3-prong plugs and
receptacles.
NOTE: The smaller the gauge number, the
heav i er the cord.
RECOMMENDED SIZES OF EXTENSION CORDS
120 VOLT ALTERNATING CURRENT TOOLS
BEARINGS
Model 4000 has ball bearing construction.
Under normal use no additional lubrication is
required.
Cleaning
To avoid accidents always
dis connect the tool from
the power supply before cleaning or
performing any main tenance. The tool may
be cleaned most effectively with compressed
dry air. Always wear safety gog gles when
cleaning tools with compressed air.
Ventilation openings and switch levers must be
kept clean and free of foreign matter. Do not
at tempt to clean by inserting pointed objects
through openings.
Certain cleaning agents
and sol vents damage
plastic parts. Some of these are: gasoline,
carbon tetrachlo ride, chlo rinated cleaning
solvents, ammonia and house hold detergents
that contain ammonia.
!
WARNING
CAUTION
!
Tool’s
Ampere
Rating
Cord Size in A.W.G.
Wire Sizes in mm
2
3-6
6-8
8-10
10-12
12-16
18 16 16 14 0.75 0.75 1.5 2.5
18 16 14 12 0.75 1.0 2.5 4.0
18 16 14 12 0.75 1.0 2.5 4.0
16 16 14 12 1.0 2.5 4.0
14 12 —— ——
25 50 100 150 15 30 60 120
Cord Length in Feet Cord Length in Meters
Dremel Accessories
Use only Dremel
®
, high-performance accessories. Other accessories are not
designed for this tool and may lead to personal injury or property damage.
!
WARNING
The number and variety of accessories for the
Rotary Tool are almost limitless. There is a
category suited to almost any job you might
have to do — and a variety of sizes and shapes
within each category which en ables you to get
the perfect accessory for every need.
Collets
If you expect to use a variety of accessories,
we recommend that in the beginning you
purchase a complete set of four collets. Store
these so that you will have the proper size of
collet for any accessory or drill bit you want to
use. Currently, the 1/8", 3/32",1/32" and
1/16" collets accommodate all of the avail -
able Dremel accessories. 1/8" collets are
included in most rotary tool kits.
Mandrels
A mandrel is a shank with a threaded or screw
head, which are required when you use
polishing accessories, cutting wheels, sanding
discs, and pol ish ing points. The reason
mandrels are used is that sanding discs,
cutting wheels and similar accesso ries must be
replaced frequently. The mandrel is a per -
manent shank, allowing you to replace only the
worn head when necessary, thus saving the
expense of replacing the shaft each time.
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 14
15
High Speed Cutters
Available in many shapes, high speed cutters
are used in carving, cutting and slotting in
wood, plastics and soft metals such as
aluminum, copper and brass. These are the
accessories to use for freehand routing or
carving in wood or plastic, and for precision
cutting. Made of high quality steel. 1/8" shank.
Tungsten Carbide Cutters
These are tough, long-lived cutters for use on
hard ened steel, fired ceramics and other very
hard ma terials. They can be used for
engraving on tools and garden equipment. 1/8"
shanks.
Engraving Cutters
This group has a wide variety of sizes and
shapes, and are made for intricate work on
ceramics (greenware), wood carvings, jewelry
and scrimshaw. They often are used in making
complicat ed printed circuit boards. They
should not be used on steel and other very
hard materials but are excellent on wood,
plastic and soft metals. 3/32" shank.
Structured Tooth Tungsten Carbide Cutters
Fast cutting, needle-sharp teeth for greater
material removal with minimum loading. Use
on fiberglass, wood, plastic, epoxy and rubber.
1/8" shank.
Aluminum Oxide Grinding Stones
(red/brown)
Round, pointed, flat you name the shape
and there is one available in this category.
These are made of aluminum oxide and cover
virtually every possible kind of grinding
application. Use them for sharpening lawn
mower blades, screwdriver tips, knives,
scissors, chisels and other cutting tools. Use to
remove flash from metal castings, deburring
any metal after cutting, smoothing welded
joints, grinding off rivets and re mov ing rust.
These grinding stones can be resharped with a
dressing stone. In machine shops, high speed
drills and cut ters normally are ground with
aluminum oxide wheels. 1/8" shank.
Silicon Carbide Grinding Stones
(blue/green)
Tougher than aluminum oxide points, these are
made es pecially for use on hard materials
such as glass and ce ramics. Typical uses
might be the removal of stilt marks and excess
glaze on ceramics and engraving on glass.
1/8" shank.
Diamond Wheel Points
Excellent for fine detail work on wood, jade,
ceramic, glass and other hard material. Bits
are covered with diamond particles. 3/32"
shanks. (Not recommended for drilling)
Screw Mandrel N° 401
This is a screw mandrel used with the felt
polishing tip and felt polishing wheels. 1/8"
shank.
Small Screw Mandrel N° 402
This is a mandrel with a small screw at its tip,
and is used with emery and fiberglass cutting
wheels, sanding discs and polishing wheels.
1/8" shank.
EZ Lock Mandrel N° 402
The Dremel EZ Lock makes accessory
changes easy as PULL - TWIST - RELEASE.
The one-piece mandrel design simplifies the
process of changing cutting wheels, buffs and
detail abrasive brushes (EZ Lock compatible
accessories).
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 15
16
Wire Brushes
Three different shapes of wire brushes are
available. For best results wire brushes
should be used at speeds not greater than
15,000 RPM. Refer to Operating Speeds
section for proper tool speed setting. The
three shapes come in three different materials:
stainless steel, brass and carbon wire. The
stainless steel perform well on pewter,
aluminum, stainless steel, and other metals,
without leaving "after-rust". Brass brushes are
non sparking, and softer than steel; making
them good for use on soft metal like gold,
cooper and brass. The carbon wire brushes
are good for general purpose cleaning.
Bristle Brushes
These are excellent cleaning tools on
silverware, jew elry and antiques. The three
shapes make it possible to get into tight
corners and other difficult places. Bristle
brushes can be used with polishing compound
for faster cleaning or polishing.
Brushing Pressure
1. Remember, the tips of a wire brush do the
work. Operate the brush with the lightest
pressure so only the tips of the wire come in
contact with the work.
2. If heavier pressures are used, the wires will
be overstressed, resulting in a wiping action;
and if this is continued, the life of the brush will
be shortened due to wire fatigue.
3. Apply the brush to the work in such a way
that as much of the brush face as possible is in
full contact with the work. Applying the side or
edge of the brush to the work will result in wire
breakage and shortened brush life.
Polishing Accessories
These include an impregnated polishing point
and an impregnated polishing wheel for
bringing metal sur faces to smooth finish; a felt
polishing tip and felt polish ing wheel, and cloth
polishing wheel, all used for polishing plastics,
metals, jewelry and small parts. Also included
in this group is a polishing compound (No. 421)
for use with the felt and cloth polishers.
Polishing points make a very smooth surface,
but a high luster is obtained using felt or cloth
wheels and polishing compound. For best
results polishing accessories should be
used at speeds not greater than 15,000
RPM.
No polishing compound is needed when using
the 425 Polishing Wheel.
Aluminum Oxide Abrasive Wheels
Use to remove paint, deburr metal, polish
stainless steel and other metals. Available in
medium grit. 1/8" shank.
Dremel Accessories (Cont.)
CORRECT:
Wire tips doing the work.
INCORRECT:
Excessive pressure can cause wire breakage.
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 16
17
Sanding Accessories
Sanding discs in fine, medium and coarse
grades are made to fit mandrel No. 402. They
can be used for nearly any small sanding job
you might have, from model making to fine
furniture finish ing. In addition, there is the drum
sander, a tiny drum which fits into the Rotary
Tool and makes it possible to shape wood,
smooth fiberglass, sand inside curves and
other diffi cult places, and other sanding jobs.
You replace the sanding bands on the drum as
they become worn and lose their grit. Bands
come in fine medium and coarse grades.
Flapwheels grind and polish flat or contoured
surfaces. They are used most effectively as a
finishing sander after heavier surface sanding
and material removal is completed. Flapwheels
come in fine and coarse grades. Buffs are a
great finishing accessory for cleaning and light
sanding. They work effectively on metal, glass,
wood, aluminum and plastics. Coarse and
medium buffs are sold together. Fine buffs are
sold individually. Do not exceed 15,000 RPM in
speed. 1/8" shank.
Grinding Wheel
Use for deburring, removing rust, and general
purpose grinding. Use with Mandrel #402.
Cutting Wheels
These thin discs of emery or fiberglass are
used for slicing, cutting off and similar
operations. Use them for cutting off frozen bolt
heads and nuts, or to reslot a screw head
which has become so damaged that the
screwdriver won’t work in it. Fine for cutting
BX cable, small rods, tubing, cable and cutting
rectangular holes in sheet metal.
Drywall Cutting Bit
Gives you fast, clean cuts in drywall.
Tile Cutting Bit
Cuts ceramic wall tile, cement board, and
plaster.
Spiral Cutting Bit
Cuts through all types of wood and wood
composites.
High Speed Router Bits
For routing, inlaying, and mortising in wood
and other soft materials. Use with Dremel No.
335 Router attachment and No. 231
Shaper/Router table.
Dremel Accessories (Cont.)
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 17
18
Mandrel 402 has a small screw at its tip,
and is used with emery cutting wheels and
sanding discs. Higher speeds, usually
maximum, are best for most work, including
cutting steel. Which is shown here.
Mandrel No. 401 is used with the felt
polishing tip and wheels. Thread the tip on to
the screw carefully. The felt tip must thread
down straight on the screw Mandrel, and be
turned all the way to the collar.
To replace a band on the Drum Sander,
loosen the screw without removing it to
contract the drum then slide the old band off.
Slide the new sanding band on and then
expand the drum by tightening the screw once
again.
Before each use, check to
make certain that all
components are assembled to accessory
shank and that the drum is sufficiently
expanded to secure the band during use. If
sanding band is loose on the drum during
operation it may “fly off and strike you or
bystanders.
!
WARNING
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 18
19
Catalog Soft Hard Laminates Steel Aluminum, Shell/ Ceramic Glass
Number Wood Wood /Plastic Brass, etc. Stone
7103, 7105, 25-35 18-24 -- -25-35 25-35 25-35
7117, 7120,
7122, 7123,
7134, 7144
Diamond Wheel Points
Catalog Soft Hard Laminates Steel Aluminum, Shell/ Ceramic Glass
Number Wood Wood /Plastic Brass, etc. Stone
9931, 9932, 25-35 18-24 9-11 - 12-17 ---
9933, 9934,
9935, 9936
Structured Tooth Tungsten Carbide Cutters
* Speed for light cuts; Caution - burning on deep grooves.
• Depending on cutting direction relative to grain.
Note: Each number settings listed in the speed charts = 000 RPM’s
Speed Settings
Catalog Soft Hard Laminates Steel Aluminum, Shell/ Ceramic Glass
Number Wood Wood /Plastic Brass, etc. Stone
100, 121, 131 25-35 25-35 12-17 12-17 18-24 ---
114, 124, 25-35 12-17 9-11 12-17 12-17 ---
134, 144
190 25-35 25-35 9-11 12-17 25-35 ---
118, 191, 192, 25-35 25-35 9-11 12-17 25-35 ---
193, 194
116, 117, 25-35 12-17 9-11 12-17 12-17 ---
125, 196
115 25-35 25-35 9-11 12-17 12-17 ---
198 25-35 18-24 9-11 12-17 12-17 ---
199 25-35 18-24 9-11 12-17 12-17 ---
High Speed Cutters
Catalog Soft Hard Laminates Steel Aluminum, Shell/ Ceramic Glass
Number Wood Wood /Plastic Brass, etc. Stone
105, 108 25-35 25-35 18-24 9-11 12-17 ---
106, 109, 25-35 25-35 12-17 9-11 12-17 ---
107, 110 25-35 25-35 12-17 9-11 12-17 ---
111 25-35* 25-35* 18-24* 9-11 12-17 ---
112 25-35* 25-35* 12-17* 9-11 12-17 ---
113 25-35* 25-35* 12-17* 9-11 12-17 ---
Engraving Cutters
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 19
20
Catalog Soft Hard Laminates Steel Aluminum, Shell/ Ceramic Glass
Number Wood Wood /Plastic Brass, etc. Stone
9901, 9902, 25-35 18-24 9-11 25-35 12-17 18-24 18-35 18-35
9903, 9904,
9905, 9906,
9909, 9910,
9911
Speed Settings (Continued)
Catalog Soft Hard Laminates Steel Aluminum, Shell/ Ceramic Glass
Number Wood Wood /Plastic Brass, etc. Stone
612, 640 25-35* 18-24 -- - ---
615, 617, 618, 25-35* 25-35 -- - ---
650, 652, 654 25-35* 18-24 -- - ---
High Speed Router Bits
Catalog Soft Hard Laminates Steel Aluminum, Shell/ Ceramic Glass
Number Wood Wood /Plastic Brass, etc. Stone
83142, 83322, --12-17 25-35 9-11 12-17 25-35 25-35
83702, 84922,
85422, 85602,
85622
Silicon Carbide Grinding Stones (blue/green)
Catalog Soft Hard Laminates Steel Aluminum, Shell/ Ceramic Glass
Number Wood Wood /Plastic Brass, etc. Stone
516 9-17 9-17 - 18-24 12-17 ---
500 9-17 9-17 - 18-24 9-17
EZ541GR -- -12-24 9-17 ---
Abrasive Wheels/Points
Tungsten Carbide Cutters
Catalog Soft Hard Laminates Steel Aluminum, Shell/ Ceramic Glass
Number Wood Wood /Plastic Brass, etc. Stone
541,903, 911, 25-35 25-35 - 18-24 9-11 12-17 25-35 -
921, 932, 941,
945, 952, 953,
954, 971, 997,
8153, 8175,
8193, 8215
Aluminum oxide grinding stones (orange/bown)
* Speed for light cuts; Caution - burning on deep grooves.
• Depending on cutting direction relative to grain.
Note: Each number settings listed in the speed charts = 000 RPM’s
DM 2610029871 12-12_DM 2610029871 12-12.qxp 12/12/12 2:36 PM Page 20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Dremel 100 Manuel utilisateur

Catégorie
Outils électroportatifs
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues