Thermador PRD364GDHU Guide d'installation

THERMADOR PROFESSIONAL

TM

PRO HARMONY

®

Dual Fuel Ranges

THERMADOR PROFESSIONAL

TM

PRO HARMONY

®

Dual Fuel Ranges

Cuisinières Mixtes PROFESSIONAL PRO HARMONY

mc

de THERMADOR

Estufas Mixtas PROFESSIONAL PRO HARMONY

®

de THERMADOR

Table of Contents............................................................................... 2

Table de Matières ............................................................................ 28

Índice de Materias ........................................................................... 54

Models | Modèles | Modelos

PRD304GHC

PRD304GHU

PRD364GDHC

PRD364GDHU

PRD366GHC

PRD366GHU

PRD486GDHC

PRD486GDHU

PRD364NLHU

PRD364NLHC

PRD486NLHU

PRD486NLHC

PRD484NCHU

PRD484NCHC

Table of Contents English 2

Table of Contents

This THERMADOR

®

appliance is made by

BSH Home Appliances Corporation

1901 Main Street, Suite 600

Irvine, CA 92614

Questions?

1-800-735-4328

www.thermador.com

We look forward to hearing from you!

Safety Instructions ....................................................................................................................................................... 3

Installation ..................................................................................................................................................................... 5

Planning Information ................................................................................................................................................. 5

STEP 1: Ventilation Requirements .......................................................................................................................... 5

STEP 2: Cabinet Preparation ................................................................................................................................... 6

STEP 3: Unpacking, Moving and Placing the Range ............................................................................................. 12

STEP 4: Installing Anti-Tip Device ......................................................................................................................... 13

STEP 5: Gas Requirements and Hookup .............................................................................................................. 14

STEP 6: Electrical Requirements, Connection & Grounding ................................................................................. 16

STEP 7: Backguard Installation (optional) .............................................................................................................. 18

STEP 8: Door Removal and Reinstallation ............................................................................................................ 22

STEP 9: Placing and Leveling the Range............................................................................................................... 24

STEP 10: Burner Test ............................................................................................................................................ 26

Installer Checklist ....................................................................................................................................................... 27

Customer Support, Accessories & Parts .....................................................................................................back page

Safety Definitions

NOTICE: This indicates that damage to the appliance or property may occur as a result of non-compliance with this

advisory.

Note: This alerts you to important information and/or tips.

WARNING

This indicates that death or serious injuries may occur as

a result of non-observance of this warning.

CAUTION

This indicates that minor or moderate injuries may occur

as a result of non-observance of this warning.

Installation Instructions English 3

Safety

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Before You Begin

IMPORTANT: Save these Instructions for the Local Gas

Inspector’s use.

INSTALLER: Please leave these Installation Instructions

with this unit for the owner.

OWNER: Please retain these instructions for future

reference.

Examine the appliance after unpacking it. In the event of

transport damage, do not plug it in.

Remove all tape and packaging before using the appliance.

Destroy the packaging after install. Never allow children to

play with packaging material.

IMPORTANT:

Local codes vary. Installer is responsible for ensuring that

the installation, gas connections, and grounding comply

with all applicable codes. Failure to follow appropriate local

codes and regulations may void the warranty.

NOTE: This range is NOT designed for installation in

manufactured (mobile) homes or Recreational Park

Trailers.

GROUNDING INSTRUCTIONS

This appliance must be grounded. Grounding reduces the

risk of electric shock by providing a safe pathway for

electric current in the event of a short circuit.

DO NOT install this range outdoors.

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect power before installing or servicing.

Before turning power ON, be sure that all

controls are in the OFF position. Failure to do

so can result in death or electrical shock.

FOR MASSACHUSETTS INSTALLATIONS:

1. Installation must be performed by a qualified or

licensed contractor, plumber or gas fitter qualified or

licensed by the state, province or region where this

appliance is being installed.

2. Shut-off valve must be a “T” handle gas cock.

3. Flexible gas connector must not be longer than 36''

(914 mm).

WARNING

A child or adult can tip the range over and

be killed or seriously injured. Verify that

the anti-tip bracket is securely installed.

Ensure the anti-tip bracket is engaged

when the range is moved.

DO NOT operate the range without the anti-tip bracket in

place. Failure to follow the instructions in this manual

can result in death or serious burns to children and

adults.

Check for proper installation and use of anti-tip bracket.

Carefully tip range forward pulling from the back to

ensure that the anti-tip bracket engages the range leg

and prevents tip-over. Range should not move more

than 1'' (2.5 cm).

WARNING

If the information in this manual is not followed exactly, a

fire or explosion may result causing property damage,

personal injury or death.

— DO NOT store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electrical switch.

• DO NOT use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

fire department.

— Installation and service must be performed by a

qualified installer, service agency or the gas

supplier.

Installation Instructions English 4

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Gas Type Verification

Verify the type of gas supplied to the location. Ensure that

the appliance is connected to the type of gas for which it is

certified. All models are certified for use with natural gas.

Field conversion of the appliance for use with propane gas

supply will require a conversion kit (PALPKITHN).

Gas Supply

Natural Gas — 6 inch water column. (14.9 mb) min., 14

inch (34.9 mb) maximum

Propane Gas — 11 inch water column. (27.4 mb) min., 14

inch (34.9 mb) maximum

Electric Power Supply

See “STEP 6: Electrical Requirements, Connection &

Grounding” on page 16 for specifications.

Check local building codes for the proper method of

appliance installation. Local codes vary and

it is the

responsibility of the installer to ensure installation is in

accordance with these codes. Installation, electrical

connections and grounding must comply with all applicable

codes. In the absence of local codes the appliance should

be installed in accordance with the National Fuel Gas Code

ANSI Z223.1/NFPA 54 current issue and National Electrical

Code ANSI/NFPA 70-current issue. In Canada, installation

must be in accordance with the CAN 1-B149.1 and .2 –

Installation Codes for Gas Burning Appliances and/or local

codes.

This appliance complies with the following standards:

• UL 858, Standard for the Safety of Household Electric

Ranges

• ANSI Z21.1, American National Standard for

Household Cooking Gas Appliances

• CAN 1-1. 1-M81, Domestic Gas Ranges

• CAN/CSA-C22.2 No. 61, Household Cooking Ranges

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

IMPORTANT:

When installing against a combustible surface, a Low

Backguard is required. A THERMADOR

TM

Low Backguard

must be purchased separately. See Step 7 for backguard,

kits and installation information.

When using the Flush Island Trim, THERMADOR

recommends a minimum 12'' (305 mm) rear clearance to a

combustible surface (see “Installation Clearances”).

Clearances from non-combustible materials are not part of

the ANSI Z21.1 scope and are not certified by

CSA. Clearances of less than 12'' (305 mm) must be

approved by the local codes and/or by the local authority

having jurisdiction.

Refer to Table 3, Backguard Kit Model Numbers, for the

correct backguard models that are designed for this range.

After selecting the correct backguard, the range must be

installed properly, using the minimum clearances to

combustible surfaces specified in the Cabinet Preparation

instructions beginning on page 6.

CAUTION

When connecting the unit to propane gas, make certain

the propane gas tank is equipped with its own high-

pressure regulator in addition to the pressure regulator

supplied with the range. The maximum gas pressure to

this appliance must not exceed 14.0” water column

(34.9 mb) from the propane gas tank to the pressure

regulator.

WARNING

To avoid possible burn or fire hazard, a backguard

designed specifically for this range must be installed

whenever the range is used.

CAUTION

To eliminate risk of burns or fire caused by reaching over

heated surface units, cabinet storage located above the

surface units should be avoided.

CAUTION

This unit is designed as a cooking appliance. Based on

safety considerations, never use it for warming or

heating a room.

WARNING

State of California Proposition 65 Warnings:

This product contains chemicals known to the State of

California to cause cancer, birth defects or other

reproductive harm.

Installation Instructions English 5

Installation

Planning Information

Before using your appliance, be sure to read this manual.

Pay special attention to the Important Safety Instructions

located at the beginning of the manual.

STEP 1: Ventilation

Requirements

Refer to the Ventilation Planning Guide for approved

ventilation combinations.

It is strongly recommended that this appliance be installed

in conjunction with a THERMADOR vent hood. Due to the

high heat capability of this unit, particular attention should

be paid to the hood and duct work installation to assure it

meets local building codes.

Downdraft ventilation should not be used. The Ventilation

Planning Guide indicates the ventilation hood options and

blower capacity guidelines that are recommended for use

with all THERMADOR ranges.

Due to the high heat of the rangetop burners, do not install

a microwave oven/ventilator combination above the range,

as these type of units do not provide the proper ventilation

and are not suitable for use with the range.

IMPORTANT:

Ventilation hoods and blowers are designed for use with

single wall ducting. However, some local building codes or

inspectors may require double wall ducting. Consult local

building codes and/or local agencies, before starting, to

assure that hood and duct installation will meet local

requirements.

NOTICE: Most range hoods contain combustible

components which must be considered when planning the

installation.

Ventilation Preparation

1. Select Hood and Blower Models:

• For wall installations, the hood width must, at a

minimum, equal the width of the range. Where

space permits, a hood larger in width than the

range/rangetop may be desirable for improved

ventilation performance.

• For island installations, the hood width should

overhang the width of the range by a minimum of

3" (76 mm) on each side.

2. Hood Placement:

• For best smoke elimination, the lower edge of the

hood should be installed 30" (762 mm) above the

range cooking surface (see “Installation

Clearances”).

• If the hood contains any combustible materials (i.e.

a wood covering), it must be installed a minimum of

36" (914 mm) above the cooking surface (see

“Installation Clearances”).

TOOLS NEEDED

7/16'' box end wrench or

ratchet

1/8'' (3.17 mm) drill bit

3/16'' (4.76 mm) drill bit 12'' Adjustable wrench

Hand or electric drill Tape measure

T-20 Torx screwdriver Marking instrument

Level Furniture dolly

Phillips & flathead

screwdrivers

Protective gloves

ITEMS NOT INCLUDED

Drywall / Concrete Anchors Pipe Compound / Tape

Rope/Twine ¾" (19 mm) Flex Line

Strain Relief Cord Kit or Conduit

2 – NPT Flare Adapters

WARNING

This appliance should not be installed with a ventilation

system that directs air in a downward direction toward

the range. This type of ventilation system may cause

ignition and combustion problems with the appliance

resulting in personal injury, property damage, or

unintended operation. Ventilating systems that direct the

air upwards do not have any restriction.

Installation Instructions English 6

3. Consider Make-Up Air:

• Due to the high volume of ventilation air, a source

of outside replacement air is recommended. This is

particularly important for tightly sealed and

insulated homes. A qualified heating and

ventilating contractor should be consulted.

STEP 2: Cabinet Preparation

• The range is a free standing unit. If the unit is to be

placed adjacent to cabinets, the clearances shown in

“Installation Clearances” beginning on page 7 are

required. The same clearances apply to island

installations, except for the overhead cabinets, which

must have a space wide enough to accept the flared

island hood.

• Any openings in the wall behind the range and in the

floor under the range must be sealed.

• The gas and electrical supply should be within the

zones shown in Figure 5 on page 11.

• When installing against a combustible surface, a Low

Backguard is required. A THERMADOR

TM

Low

Backguard must be purchased separately (see Table 3

on page 18).

• When using the Flush Island Trim, THERMADOR

recommends a minimum 12'' (305 mm) rear clearance

to a combustible surface (see “Installation

Clearances”). Clearances from non-combustible

materials are not part of the ANSI Z21.1 scope and are

not certified by CSA. Clearances of less than 12''

(305 mm) must be approved by the local codes and/or

by the local authority having jurisdiction.

• When the range is installed against a combustible side

wall a minimum clearance of 5'' (127 mm) is needed

from the side of the range to the wall.

• Always keep appliance area clear from combustible

materials, gasoline and other flammable vapors and

liquids.

• The maximum depth of overhead cabinets installed on

either side of the hood is 13" (330 mm). Wall cabinets

must be 18'' (457 mm) above the countertop.

• The top edges of the range’s side panels must be on

the same or higher level as the adjacent countertop. If

the range is operated while at a lower height relative to

the adjacent cabinet, the cabinet could be exposed to

excessive temperatures, causing damage to the

cabinet and countertop.

• DO NOT obstruct the flow of combustion and

ventilation air to the unit.

• There is a 36'' (914 mm) minimum clearance required

between the top of the cooking surface and the bottom

of an unprotected cabinet. A 30'' (762 mm) clearance

can be used when the bottom of the wood or metal

cabinet is protected by not less than 1/4'' (6 mm) of a

flame retardant material covered with not less than No.

28 MSG sheet steel, 0.015'' (0.38 mm) thick stainless

steel, 0.024'' (0.61 mm) aluminum, or 0.02'' (0.51 mm)

thick copper.

Flame retardant materials bear the mark:

UNDERWRITERS LABORATORIES INC. CLASSIFIED

MINERAL AND FIBER BOARDS SURFACE BURNING

CHARACTERISTICS, followed by the flame spread and

smoke ratings. These designations are shown as “FHC

(FIame Spread/Smoke Developed).” Materials with “O”

flame spread ratings are flame retardant. Local codes may

allow other flame spread ratings. It is the responsibility of

the installer to ensure installation is in accordance with

these ratings.

Installation Instructions English 7

Installation Clearances

Installation Clearances with Lowback

Figure 1: Cabinet Clearances

5

" (127 mm) min.

to combustible

sidewalls

5

" (127 mm) mi

n.

to combustib

le

sidew

alls

5

" (127 mm) min.

to combustible

sidewalls

30" (762 mm) min.

from bottom of overhead

hood to cooking surface.

36" (914 mm) min. if

hood contains

combustible material

30" (762 mm) mi

n.

from bottom of overhead

hood to cooking s

urface.

36" (914 mm) mi

n. if

hood contains

combustible material

30" (762 mm) min.

from bottom of overhead

hood to cooking surface.

36" (914 mm) min. if

hood contains

combustible material

13" max.

cabinet

depth

13" max.

cabinet

depth

13" max.

cabinet

depth

m CAUTION!

36" (914 mm) min.

to combustible

material

from Cooking

Surface

CAUTION!

36" (914 mm) min.

to combustible

material

from Cooking

Surface

CAUTION!

36" (914 mm) min.

to combustible

material

from Cooking

Surface

as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition).

Clearances from non-combustible materials are not part of the ANSI Z21.1

scope and are not certified by CSA. Clearances of less than 12" (305 mm)

must be approved by the local codes and/or by the local authority having

jurisdiction.

The range height is adjustable.

The level of the range top must

be at the same level or above

the counter top level.

*35 ¾" (908 mm) Min. range

height with leveling legs fully

retracted.

*37 ¼" (946 mm) Max. range

height with leveling legs fully

extended.

The range height is adjustable.

The level of the range top must

be at the same level or above

the counter top level.

*35 ¾" (908 mm) Min. range

height with leveling legs fully

retracted.

*37 ¼" (946 mm) Max. range

height with leveling legs fully

extended.

The range height is adjustable.

The level of the range top must

be at the same level or above

the counter top level.

*35 ¾" (908 mm) Min. range

height with leveling legs fully

retracted.

*37 ¼" (946 mm) Max. range

height with leveling legs fully

extended.

30", 36", or 48"

(762, 914, or 1219 mm)

30", 36", or 48"

(762, 914, or 1219 mm)

30", 36", or 48"

(762, 914, or 1219 mm)

For Gas Supply &

Electrical Zones

see Figure 5.

For Gas Supply &

Electrical Zones

see Figure 5.

For Gas Supply &

Electrical Zones

see Figure 5.

18

" (457 mm)

minimum

18

" (457 mm)

mini

mum

18

" (457 mm)

minimum

See the Ventilation Planning Guide

for recommended hood options.

See the Ventilation Planning Guide

for recommended hood options.

See the Ventilation Planning Guide

for recommended hood options.

Installation Instructions English 8

Figure 2: Installation Clearances with a Low Backguard

as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition).

Clearances from non-combustible materials are not part of the ANSI Z21.1

scope and are not certified by CSA. Clearances of less than 12” (305 mm)

must be approved by the local codes and/or by the local authority having jurisdiction.

Combustible

Materials

28" (711 mm)

27¼" (692 mm)

36" (914 mm) min.

to combustible

materials

24" (610 mm)

max. recess depth

Combustible

Back Wall

35 ¾" (908 mm) Min.

37 ¼" (946 mm) Max.

23" (584 mm)

44⅞

"

(1140 mm)

Total Clearance

Installation Clearances with Low Backguard

9" (229 mm)

Low Back

24⅝" (625 mm)

24¾" (629 mm)

Installation Instructions English 9

Installation Clearances with Flush Island Trim

Figure 3: Cabinet Clearances with Flush Island Trim

5

" (127 mm) min.

to combustible

sidewalls

5

" (127 mm) mi

n.

to combusti

ble

sidew

alls

5

" (127 mm) min.

to combustible

sidewalls

30" (762 mm) min.

from bottom of overhead

hood to cooking surface.

36" (914 mm) min. if

hood contains

combustible material

30" (762 mm) mi

n.

from bottom of overhead

hood to cooking s

urface.

36" (914 mm) mi

n. if

hood contains

combustible material

30" (762 mm) min.

from bottom of overhead

hood to cooking surface.

36" (914 mm) min. if

hood contains

combustible material

13" max.

cabinet

depth

13" max.

cabinet

depth

13" max.

cabinet

depth

m CAUTION!

36" (914 mm) mi

to combustible

material

from Cooking

Surface

CAUTION!

36" (914 mm) min.

to combustible

material

from Cooking

Surface

CAUTION!

36" (914 mm) mi

to combustible

material

from Cooking

Surface

as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition).

Clearances from non-combustible materials are not part of the ANSI Z21.1

scope and are not certified by CSA. Clearances of less than 12" (305 mm)

must be approved by the local codes and/or by the local authority having

jurisdiction.

The range height is adjustable.

The level of the range top must

be at the same level or above

the counter top level.

*35 ¾" (908 mm) Min. range

height with leveling legs fully

retracted.

*37 ¼" (946 mm) Max. range

height with leveling legs fully

extended.

The range height is adjustable.

The level of the range top must

be at the same level or above

the counter top level.

*35 ¾" (908 mm) Min. range

height with leveling legs fully

retracted.

*37 ¼" (946 mm) Max. range

height with leveling legs fully

extended.

The range height is adjustable.

The level of the range top must

be at the same level or above

the counter top level.

*35 ¾" (908 mm) Min. range

height with leveling legs fully

retracted.

*37 ¼" (946 mm) Max. range

height with leveling legs fully

extended.

30", 36", or 48"

(762, 914, or 1219 mm)

30", 36", or 48"

(762, 914, or 1219 mm)

30", 36", or 48"

(762, 914, or 1219 mm)

For Gas Supply &

Electrical Zones

see Figure 5.

For Gas Supply &

Electrical Zones

see Figure 5.

For Gas Supply &

Electrical Zones

see Figure 5.

18

" (457 mm)

minimum

18

" (457 mm)

mini

mum

18

" (457 mm)

minimum

See the Ventilation Planning Guide

for recommended hood options.

See the Ventilation Planning Guide

for recommended hood options.

See the Ventilation Planning Guide

for recommended hood options.

Shaded area above

countertop indicates min.

clearance to combustible

surfaces, combustible

materials cannot be located

within this area.

Shaded area above

countertop indicates min.

clearance to combustible

surfaces, combustible

materials cannot be located

within this area.

Shaded area above

countertop indicates min.

clearance to combustible

surfaces, combustible

materials cannot be located

within this area.

Installation Instructions English 10

Figure 4: Installation Clearances with a Flush Island Trim

as defined in the “National Fuel Gas Code” (ANSI Z223.1, Current Edition).

Clearances from non-combustible materials are not part of the ANSI Z21.1

scope and are not certified by CSA. Clearances of less than 12” (305 mm)

must be approved by the local codes and/or by the local authority having jurisdiction.

Combustible

Materials

28" (711 mm)

27¼" (692 mm)

36" (914 mm) min .

to combustible

materials

24" (610 mm)

max. recess depth

Cantilever

23" (584 mm)

44⅞

"

(1140 mm)

Total Clearance

Installation Clearances with Flush Island Trim

24⅝" (625 mm)

24¾" (629 mm)

If an inner wall

is used under

the cantilever counter

top, there should be a

⅛" (3 mm) gap from

the rear of the range

to the inner wall.

12" (305 mm) min. to

combustible surface

with Flush Island Trim

12" (305 mm) min. to

combustible surface

with Flush Island Trim

12" (305 mm) min. to

combustible surface

with Flush Island Trim

For Flush Island

Trim installations,

counter surface should

have a cantilever edge

meeting the back

section of the Flush

Island Trim accessory.

Shaded area behind

range indicates

minimum clearance

to combustible surfaces,

combustible materials

cannot be located within

this area.

Shaded area behind

range indicates

minimum clearance

to combustible surfaces,

combustible materials

cannot be located within

this area.

Shaded area behind

range indicates

minimum clearance

to combustible surfaces,

combustible materials

cannot be located within

this area.

35 ¾" (908 mm) Min.

37 ¼" (946 mm) Max.

Installation Instructions English 11

Gas and Electric Supply Clearances

NOTICE:

— If not already present, install gas shut-off valve in an

easily accessible location.

— Make sure all users know where and how to shut off

the gas supply to the range.

— Any opening in the wall behind the appliance and any

opening in the floor under the appliance must be

sealed.

The dual fuel ranges may be connected to the power

supply with a range supply cord kit or by hard-wiring to the

power supply. It is the responsibility of the installer to

provide the proper wiring components (cord or conduit and

wires) and complete the electrical connection as dictated

by local codes and ordinances, and/or the National Electric

Code. The units must be properly grounded. Refer to

“STEP 6: Electrical Requirements, Connection &

Grounding” on page 16 for details. Canadian models have

power cord supplied.

The range must be connected only to the type of gas

for which it is certified. If the range is to be connected to

propane gas, ensure that the propane gas supply tank is

equipped with its own high pressure regulator in addition to

the pressure regulator supplied with the range. (See “STEP

5: Gas Requirements and Hookup” beginning on page 14.)

NOTE: The range is designed for flush installation to the

back wall. For a successful installation, it may be

necessary to reposition the gas supply line and the

electrical cord as the range is pushed back to its final

position.

-- SUGGESTION: This may be accomplished by carefully

pulling on a rope or twine looped around the gas or

electrical supply line as the range is pushed back into

its final installed position.

Model A B C D

30'' (762 mm) 5¾'' (146 mm) 15

7

/

16

'' (392 mm) 5

13

/

16

'' (148 mm) 4Ǫ'' (111 mm)

36'' (913 mm) 8

1

/

16

'' (205 mm) 16

13

/

16

'' (503 mm) 8ǩ'' (206 mm) 4Ǫ'' (111 mm)

48'' (1219 mm) 4Ǫ'' (111 mm) 10¾'' (273 mm) 18

11

/

16

'' (475 mm) 5

15

/

16

'' (151 mm)

Figure 5: Gas and Electrical Supply Locations

10"

(254 mm)

10"

(254 mm)

10"

(254 mm)

B

C

3"

(76 mm)

3"

(76 mm)

3"

(76 mm)

A

D

2" (51 mm) max.

protrusion from wall

for gas or electrical

supply.

2" (51 mm) max.

protrusion from wall

for gas or electrical

supply.

2" (51 mm) max.

protrusion from wall

for gas or electrical

supply.

Gas Zone

30", 36" or 48" (762, 914 or 1219 mm)

For nearly-flush installation to

the back wall, the gas supply

line and electrical cord should

not go above this line.

For nearly-flush installation to

the back wall, the gas supply

line and electrical cord should

not go above this line.

For nearly-flush installation to

the back wall, the gas supply

line and electrical cord should

not go above this line.

Electric Zone

Installation Instructions English 12

Electrical Supply

Installation of the range must be planned so that rough-in

of terminal block for the receptacle or conduit connection

will allow maximum clearance to the rear of the unit.

When the power supply cord or conduit is connected to the

mating receptacle or terminal block cover, the combined

plug/receptacle or terminal block cover/conduit connector

should protrude no more than 2” (51 mm) from the rear

wall. See Figure 6.

Refer to Figure 10 on page 17 for location of terminal block

on unit. To minimize binding when the unit is connected to

the receptacle or terminal block, orient the receptacle or

conduit connector, and slide back into position.

When using a receptacle it may be necessary to recess the

receptacle's housing into the rear wall. Refer to Local

Electrical Code to determine the minimum volume for all

electrical / junction boxes.

Follow all local electrical codes.

Mount the receptacle securely to a wall stud, then seal

around the receptacle's housing.

NOTE: Canadian models have the power cord supplied

with range.

STEP 3: Unpacking and

Moving the Range

Unpacking the Range

1. Remove the outer carton and packing materials from

the shipping pallet but leave the adhesive-backed foam

layer over brushed-metal surfaces, to protect finish

from scratches, until the range is installed in its final

position.

2. It is recommended that the grates, griddle plate, burner

caps and oven racks be removed to facilitate handling.

If desired, the oven doors may also be removed (see

“STEP 8: Door Removal and Adjustment” on page 22).

Do not remove the griddle assembly.

Figure 6: Wall Connection

2” (51 mm) maximum

when plugged in

2” (51 mm)

maximum

Power Cord & Receptacle

Junction Box & Conduit

CAUTION

DO NOT lift the range by the oven door’s

handle, as this may damage the door hinges

and cause the door to fit incorrectly.

DO NOT lift the appliance by the range’s

control panel.

The unit is heavy and should be handled

accordingly. Proper safety equipment such

as gloves and adequate manpower of at

least two people must be used in moving the

range to avoid injury and to avoid damage to

the unit or the floor.

Rings, watches, and any other loose items that may

damage the unit or otherwise might become entangled

with the unit should be removed.

Hidden surfaces may have sharp edges. Use caution

when reaching behind or under appliance.

DO NOT use a hand truck or appliance dolly on the back

or front of the unit. Handle from the side only.

30" 36" 48"

Shipping Weight 377 lbs

(171 kg)

395 lbs

(179 kg)

560 lbs

(254 kg)

Weight without

packing materials

293 lbs

(133 kg)

337 lbs

(153 kg)

470 lbs

(213 kg)

Table 1: Range Weight

Installation Instructions English 13

Moving the Range

Due to the weight, a furniture dolly with soft wheels or an

air lift should be used to move this unit. The weight must be

supported uniformly across the bottom.

NOTE: Step 4 through Step 8 must be completed before

the range is placed in its final position. For proper

performance, the range must be level. See “STEP 9:

Placing and Leveling the Range” on page 24 for leveling

instructions.

Removing the Pallet Bolts

1. To remove the (4) pallet bolts in the front and in the

back, use a 7/16'' wrench or ratchet and socket to

remove the pallet bolt from the bottom of the pallet.

Discard the wood packing block inserts.

2. Lift range and remove it from the pallet.

Use additional

help as required to remove from pallet.

3. Transport the range by dolly close to its final location.

Unit should not be dollied from the front.

4. The range can then be tipped back and supported on

the rear legs while the dolly is carefully removed. THE

FLOOR UNDER THE LEGS SHOULD BE

PROTECTED BEFORE PUSHING THE UNIT INTO

POSITION.

• Step 4 through Step 8 must be completed before

the range is placed in its final position. For proper

performance, the range must be level. See

“STEP 9: Placing and Leveling the Range” on

page 24 for leveling instructions.

STEP 4: Installing the Anti-Tip

Device

For all ranges, an anti-tip device must be installed as per

these instructions.

ATTENTION – PROPERTY DAMAGE

• Contact a qualified installer or contractor to determine

the proper method for drilling holes through the wall or

floor material (such as ceramic tile, hardwood, etc.)

• Do not slide the range across an unprotected floor.

• Failure to follow these instructions may result in

damage to wall or floor coverings.

Figure 7: Removal of Shipping Bolts

WARNING

RANGE TIPPING HAZARD:

— All ranges can tip and injury can result.

To prevent accidental tipping of the

range, attach it to the floor by installing

the Anti-Tip Device supplied.

— A risk of tip-over may exist if the

appliance is not installed in accordance

with these instructions. For all ranges an

anti-tip device

must be installed.

— A child or adult can tip the range and be

killed.

— DO NOT operate the range without the

anti-tip device in place and engaged.

Failure to do so can result in death or

serious burns to children or adults.

If the range is pulled away from the wall for cleaning,

service or for any other reason, ensure that the Anti-Tip

Device is properly re-engaged when the range is pushed

back against the wall. In the event of abnormal usage

(such as a person standing, sitting, or leaning on an

open door), failure to take this precaution can result in

tipping of the range. Personal injury might result from

spilled hot liquids or from the range itself.

WARNING

ELECTRICAL SHOCK HAZARD:

• Use extreme caution when drilling holes into the wall

or floor as there may be concealed electrical wires.

• Identify the electrical circuits that could be affected

by the installation of the Anti-Tip Device, then turn off

power to these circuits.

• Failure to follow these instructions may result in

electrical shock or other personal injury.

Installation Instructions English 14

Important Installation Information

• The anti-tip bracket may be attached to a solid wood

surface having a minimum wall thickness of ¾''

(19 mm).

• The thickness of the wall or floor may require use of

longer screws, available at your local hardware store.

• In all cases, at least two (2) of the bracket mounting

screws must be fastened to solid wood surface.

• Use appropriate anchors when fastening the mounting

bracket to any material other than hard-wood or metal.

Hole location preparation

• For walls, wall studs, or floors composed of solid wood

or metal, drill 1/8'' (3 mm) pilot holes.

• For walls or floors composed of drywall, sheet-rock or

other soft materials, drill 3/16'' (5 mm) holes to a

minimum depth of 1¾'' (45 mm), then tap plastic

anchors into each of the holes using a hammer.

• For walls or floors composed of concrete or concrete

block, drill 3/16'' (5 mm) holes to a minimum depth of

1¾'' (45 mm), then tap concrete anchors into each of

the holes using a hammer.

• For walls or floors having ceramic tile covering, drill

3/16'' (5 mm) holes through the tile only, then drill into

the material behind the tile as indicated immediately

above.

Mounting Anti-Tip Bracket

The floor mounted bracket shall be installed as follows:

1. Place bracket on floor in position shown in Figure 8.

• Bracket may be used in either corner of the

installation area.

2. Secure to floor and wall stud using the (4) 1½'' (38 mm)

Phillips head screws provided.

3. Later, when the unit is installed, the adjustable leg will

slide under the bracket, as shown in Figure 8.

4. If the range is moved to a new location, the Anti-Tip

Device must be removed and reinstalled.

STEP 5: Gas Requirements

and Hookup

Verify the type of gas being used at the installation site.

The appliance is shipped from the factory for use with

natural gas. It must be converted for use with propane.

A qualified technician or installer must do the

conversion. Make certain the range matches the type of

gas available at this location.

This appliance has been CSA certified for safe operation

up to an altitude of 2,000 ft (610 m) elevation above sea

level.

High Altitude — For altitudes above 2,000 feet (610 m)

elevation above sea level, adjustments can be made with

the High Altitude Packet included with the unit. If flame

performance is satisfactory, the contents in this packet will

not be required. It is required that a Certified Professional

make the high altitude adjustments during installation.

Propane (LP) Gas Appliances – The appliance must first

be converted for use with Propane (LP) Gas before it can

be converted for use at high altitude. A Propane (LP)

Conversion Kit (PALPKITHN) is required and available for

purchase from Thermador Customer Service.

SERVICE

PART NO.

QTY DESCRIPTION

00415078 4 Screw, Phillips, #10 x 1½''

00647936 1

Anti-Tip Bracket, Floor-

Mounted

Hardware provided is for mounting through standard

thickness wood studs. Installers are responsible to

provide hardware for other types of mounting situations.

Range Side Distance of X

30'' Left or Right 2¼'' (57 mm)

36'' Left or Right 2ǫ'' (67 mm)

48'' Left or Right 2½'' (64 mm)

Figure 8: Placement of Anti-Tip Bracket

C

L

C

L

x

Installation Instructions English 15

Hook Up

The gas supply connections shall be made by a competent

technician and in accordance with local codes or

ordinances. In the absence of local codes, the installation

must conform to the National Fuel Gas Code ANSI Z223.1/

NFPA54- current issue.

1. A manual gas shut-off valve must be installed external

to the appliance, in a location accessible from the front,

for the purpose of shutting off the gas supply. The

supply line must not interfere with the back of the unit.

Make sure the gas supply is turned off at the manual

shut-off valve before connecting the appliance.

• The range is supplied with its own pressure

regulator that has been permanently mounted

within the range body.

2. Use a ¾'' (19 mm) flex line to connect between the gas

supply and the appliance gas inlet. The gas supply line

connection is located at the lower right portion of all

range models (see Figure 9). The appliance gas inlet

connection is ½'' (12.7 mm) NPT.

• Use caution to avoid crimping the ¾'' (19 mm) flex

line when making bends. Suggested length of flex

line is 48" (1219 mm); however, please check local

codes for your area's requirements before

installation.

3. Use pipe sealing compound or Teflon

®

tape on the

pipe threads. DO NOT apply sealing compound or tape

to flare fittings. Take care not to apply excessive

pressure when tightening the fittings.

4. Leak testing of the appliance shall be in accordance

with the following instructions.

• Turn on gas and check supply line connections for

leaks using a soap and water solution.

• Bubbles forming indicate a gas leak. Repair all

leaks immediately after finding them.

CAUTION

When connecting unit to propane gas, make certain the

propane gas tank is equipped with its own high pressure

regulator in addition to the pressure regulator supplied

with the appliance. The pressure of the gas supplied to

the appliance regulator must not exceed 14" water

column (34.9 mb).

NATURAL GAS REQUIREMENTS

Inlet Connection: 1/2” NPT internal

(Minimum 3/4” dia. flex line)

Supply Pressure: 6" min. to 14" max. water column

(14.9 to 34.9 mb)

Manifold Pressure: 5" water column (12.5 mb)

PROPANE GAS REQUIREMENTS

Inlet Connection: 1/2” NPT internal

(Minimum 3/4” dia. flex line)

Supply Pressure: 11"min. to 14"max. water column

(27.4 mb to 34.9 mb)

Manifold Pressure: 10" water column (24.9 mb)

Figure 9: Gas Supply Connection

WARNING

Gas line must not come in contact with any components

inside back cover of range.

WARNING

Do not use a flame of any kind to check for gas

leaks.

Adapter

¾" (19 mm) external threads

½" (12.7 mm) internal threads

{

or

Manual gas shut-off valve

or

Adapter

¾" (19 mm)

Flex line

¾" (19 mm)

Flex line

¾" (19 mm)

Flex line

Manual gas shut-off valve

Installation Instructions English 16

STEP 6: Electrical

Requirements, Connection &

Grounding

Before installing, turn power OFF at the service panel. Lock

service panel to prevent power from being turned ON

accidentally.

Prior to servicing appliance, always disconnect appliance

electrical supply cord, if so equipped, from wall receptacle.

If appliance is hard-wired to power supply, disconnect

power to unit by turning off the proper circuit breaker. Lock

service panel to prevent power from being turned ON

accidentally.

A neutral supply wire must be provided from the power

source (breaker) because critical range components,

including the surface burner spark re-ignition module,

require 120 VAC to operate safely and properly.

If the correct power supply circuit is not provided, it is the

responsibility and obligation of the installer and user to

have proper power supply connected. This must be

accomplished in accordance with all applicable local codes

and ordinances by a qualified electrician. It is the

responsibility of the installer to ensure compliance of local

codes. In the absence of local codes and ordinances, the

power supply connection shall be in accordance with the

National Electric Code.

Observe all governing codes and ordinances when

grounding. In the absence of these codes or ordinances

observe National Electrical Code ANSI/NFPA No. 70

current issue. See the following information in this section

for grounding method.

Electrical wiring diagrams and schematics have been

placed in the kick panel area of the range for access by a

qualified service technician (see Figure 29 on page 25).

The ranges are to be connected to a 240/208 VAC power

supply.

Dual Fuel models must be connected to the power supply

utilizing one of the following methods. For all methods of

connection, the length of the cord or conduit/wiring must

allow the unit to be slid completely out of the cabinet

without having to unplug or disconnect the unit from the

power supply.

Recommended minimum free length of cord or conduit is

4ft (1.2 m). Electrical installations and grounding must be in

accordance with all local codes and ordinances, and/or the

National Electric Code, as applicable.

Permanent Connection (Hard Wiring)

Units may be hard wired to the power supply. The installer

must provide approved flexible aluminum conduit, ¾''

(19 mm) trade size, maximum 6ft (1.8 m) long.

Locate the terminal block on the rear of the unit and

remove cover (refer to Figure 10). The conduit must be

installed to the terminal block using an approved conduit

connector. The free end of the conduit must be connected

to a terminal block provided in the electrical supply zone,

as shown in Figure 5 on page 11.

Mount a strain relief (not provided) into the 1" (25.4 mm)

diameter hole located below the terminal block (see

Figure 10). Wiring for the unit is to be brought into the

terminal block through the conduit and through the strain

relief. The ends of the wiring must have 1/4'' (6 mm) faston

closed-loop lugs attached, preferably soldered in place.

Make the connections to the terminal block provided.

If aluminum supply wiring exists in the installation, splice

the aluminum house wiring with appropriate-thickness

gauge copper wire for adapting to the range, using special

connectors designed and certified for joining copper and

aluminum wire. Follow the connector manufacturer’s

recommended installation procedure.

CAUTION

The appliance must be isolated from the gas supply

piping system by closing its individual manual shut-off

valve during any pressure testing of the gas supply

piping system at test pressures equal to or less than 1/2

psig (3.5kPa.).

Model Volt Circuit Frequency Phase

30'' 240/208 VAC 40 Amps 60 Hz. Single

36'' 240/208 VAC 40 Amps 60 Hz. Single

48'' 240/208 VAC 50 Amps 60 Hz. Single

Table 2: Electrical Supply Circuit Requirements

WARNING

An improper 240/208 VAC power supply will cause

malfunction, damage to this appliance, and possibly

create a condition of shock hazard.

WARNING

Improper connection of aluminum house wiring can

result in a fire or shock hazard. Use only connectors

designed and certified for connecting to aluminum wire.

Installation Instructions English 17

4-Wire Connection

A unit must be connected to the power supply with a 3-

POLE, 4-CONDUCTOR cord kit rated 125/250 VOLTS, 50

AMPERES DEDICATED CIRCUIT, and marked for use

with ranges.

The cord kit must be attached to the range terminal block

with a strain relief (not provided) which will fit a 1"

(25.4 mm) diameter hole. If not already equipped, the cord

must also have 1/4'' (6 mm) faston closed-loop lugs

attached to the free ends of the individual conductors,

preferably soldered in place.

1. Locate the terminal block on the rear of the unit and

remove cover (see Figure 10).

2. Remove upper nuts only from the terminal block studs.

Do not remove lower nuts which secure range internal

wiring leads.

3. Mount strain relief (not provided with range) into the 1"

(25.4 mm) diameter hole in the back panel located

below the terminal block. Route wires up through strain

relief.

4. Secure the neutral, grounded wire of the supply circuit,

to the center stud of the terminal block with nut (see

Figure 11).

5. Secure the L1 (red) and L2 (black) power leads to the

outside terminal studs (brass colored) with nuts.

6. Remove green ground screw located beneath the

terminal block. Discard white wire.

7. Secure the bare copper ground lead to the range

chassis using the ground screw previously used for the

white wire. Be sure that neutral and ground terminals

do not touch.

8. Tighten all connections securely.

9. Reinstall the terminal block cover.

INSTALLER — show the owner the location of the circuit

breaker. Mark it for easy reference.

3-Wire Lead Connection

Where local codes and ordinances permit grounding

through neutral, and conversion of supply to 4 wire is

impractical, unit may be connected to the power supply

with a 3-POLE, 3-CONDUCTOR cord kit rated 125/250

VOLTS, 50 AMPERES DEDICATED CIRCUIT, and marked

for use with ranges.

The cord kit must be attached to the range back panel with

a strain relief which will fit a 1" (25.4 mm) diameter hole. If

not already equipped, the cord must also have 1/4'' (6 mm)

faston closed-loop lugs attached to the free ends of the

individual conductors, preferably soldered in place.

1. Locate the terminal block on the rear of the unit and

remove cover.

2. Remove upper nuts only from the terminal block studs.

Do not remove nuts which secure range internal wiring

leads.

Figure 10: Strain Relief Location

Strain Relief

Terminal Block

Figure 11: 4-Wire Connection

Red/L1

Wire

Black/L2

Wire

White/

Neutral Wire

Green/

Ground Wire

Installation Instructions English 18

3. Mount strain relief (not provided with range) into the 1"

(25.4 mm) diameter hole in the back panel located

below the terminal block (see Figure 12). Route wires

up through strain relief.

4. Secure the neutral, grounded wire of the supply circuit,

to the center stud (silver colored) of the terminal block

(see Figure 13).

5. Secure the L1 (red) and L2 (black) power leads to the

outside corresponding terminal block studs (brass

colored).

6. Secure one end of the mounted looped neutral wire,

located beneath terminal block, to the center stud of

the terminal block with nut and keep the other end of

the wire screwed into the back of the range.

7. Tighten nuts securely.

8. Reinstall the Terminal Block Cover.

INSTALLER — show the owner the location of the circuit

breaker. Mark it for easy reference.

STEP 7: Backguard

Installation (optional)

Installation methods will vary upon need. Before you begin

read these instructions carefully. Observe all local codes

and ordinances.

Backsplash Installation

(PA[30, 36, 48]JBS)

The Backsplash must be installed prior to installing an

overhead hood given that the hood shell covers the top

mounting screws of the Backsplash.

To protect against scratches, leave protective film on

Backsplash until after installation is complete.

If range is already installed, refer to the manufacturer’s

instructions to disconnect gas and power supplies. Move

range forward to gain access to rear of unit.

1. Locate and lightly mark wall studs. Wall studs are

usually installed with a 16'' or 24'' (406 or 610 mm)

space on center.

2. The height of the hood will determine the height of the

top edge of the Backsplash. The Backsplash should be

mounted so that the bottom rear edge of the hood

overlaps the Backsplash 1½'' (38 mm).

Figure 12: Strain Relief Location

Figure 13: 3-Wire Connection

Terminal Block

Strain Relief

Red/L1

Wire

Black/L2

Wire

White/

Neutral Wire

Ground link

provided on range

Model 30'' 36' 48''

Flush Island Trim Included Included Included

9" Low Back PA30GLBH PA36GLBH PA48GLBH

Table 3: Backguard Kit Model Numbers

PARTS INCLUDED TOOLS NEEDED

10 – 1'' (25.4 mm)

screws

Phillips screwdriver or

drill

1 – Backsplash Tape measure

WARNING

To reduce the risk of fire or injury to persons, check to

make sure all packaging has been removed from

accessory devices before use.

Installation Instructions English 19

3. Per each wall stud, use (2) 1'' (25.4 mm) Phillips head

screws to secure both the top and bottom of the

Backsplash (see Figure 14). Space screws evenly

across top and bottom of Backsplash.

• Due to variable wall stud widths and varying

Backsplash widths, in some cases only one wall

stud may be found at the mounting location.

4. Remove protective plastic.

Backsplash with a Keep Hot Shelf

Installation

A hood can be installed first if the Backsplash is to be

installed with a Keep Hot Shelf given that the Keep Hot

Shelf covers the top mounting screws of the Backsplash.

To protect against scratches, leave protective film on the

Backsplash until after installation is complete.

If range is already installed, refer to the manufacturer’s

instructions to disconnect gas and power supplies. Move

range forward to gain access to rear of unit.

1. Locate wall studs. Wall studs are usually installed with

a 16'' (406 mm) or 24'' (610 mm) space on center.

2. The height of the hood will determine the height of the

top edge of the Backsplash. The Backsplash should be

mounted so that the bottom rear edge of the Keep Hot

Shelf overlaps the Backsplash 1½'' (38 mm).

3. At the locations indicated in Figure 16, mount the lower

shelf brackets included with the Keep Hot Shelf

through the Backsplash and into the wall studs.

• Due to variable wall stud widths and varying

Backsplash widths, in some cases, only one wall

stud may be found at the mounting location.

4. Remove Backsplash protective covering.

5. Start with the Keep Hot Shelf Installation.

Figure 14: Backsplash Installation

Figure 15: Backsplash with a Keep Hot Shelf

42” (1067 mm)

30”, 36”, 48”

(762, 914, 1219 mm)

Figure 16: Backsplash with a Keep Hot Shelf

La page charge ...

Thermador PRD364GDHU Guide d'installation

Ce manuel convient également à

Thermador PRD364GDHU Guide d'installation

dans d''autres langues

Documents connexes

Autres documents