Whirlpool WFW8740DC1 Le manuel du propriétaire

Marque: Whirlpool

Modèle: WFW8740DC1

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Whi ®

Use & Care Guide

Guide d'utilisation et d'entretien

Front-Loading Automatic Washer

Laveuse automatique _ chargement frontal

Para obtener acceso al

Manual de uso y

cuidado en espaSol, o para

obtener informaci6n adicional

acerca de su producto, visite:

www.whirlpool.com

If you have any problems or questions, visit us at www.whirlpool.com

Designed to use only HE

High Efficiency detergents.

Con£ue pour I'utilisation

d'un d_tergent haute

efficacit_ seulement.

W10656460A

W10656461A =SP

Table of Contents

WASHER SAFETY...................................................................2

ACCESSORIES........................................................................3

CONTROL PANELAND FEATURES......................................4

USING THE DISPENSER DRAWER.......................................6

CYCLE GUIDE.........................................................................7

USING YOUR WASHER..........................................................9

WASHER MAINTENANCE....................................................13

TROUBLESHOOTING...........................................................16

WARRANTY...........................................................................23

ASSISTANCE OR SERVICE..................................Back Cover

Table de mati res

SECURITE DE LA LAVEUSE................................................24

ACCESSOIRES......................................................................25

TABLEAU DE COMMANDE ETCARACTleRISTIQUES.......26

UTILISATION DU TIROIR DU DISTRIBUTEUR ...................28

GUIDE DES PROGRAMMES ................................................29

UTILISATION DE LA LAVEUSE............................................31

ENTRETIEN DE LA LAVEUSE..............................................35

DEPANNAGE.........................................................................38

GARANTIE .............................................................................47

ASSISTANCE OU SERVICE...................... Couverture artiste

Washer Safety

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,

including the following:

[] Read all instructions before using the washer.

[] Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry=cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry=cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[] Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. Ifthe hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach intothe washer if the drum, tub or agitator is

moving.

[] Do not install or store the washer where it will be exposed to

the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user-repair instructions that you understand and

have the skills to carry out.

[] See "Electrical Requirements" located in the installation

instructionsfor grounding instructions.

this time.

SAVE THESE iNSTRUCTiONS

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

Accessories

Customize your new washer and dryer with the following

genuine Whirlpool accessories. For more information on

options and ordering, call 1-800-442-9991, or visit us at:

www.whirlpool.com/accessories. In Canada, call

1-800-807-6777 or visit us at www.whirlpool.ca.

15" Pedestal

Color-matched pedestals raise the

washer and dryer to a more comfortable

working height. The large drawer provides

convenient storage.

Stack Kit

If space is at a premium, the stack kit

allows the dryer to be installed on top

of the washer.

Control Panel and Features

Not all features and cycles are available on all models.

NOTE: The control panel features a sensitive surface that responds

to a light touch of your finger. To ensure your selections are registered,

touch the control panel with your finger tip, not your fingernail. When

selecting a setting or option, simply touch its name.

COLD WASH --- WHITES _j_

DELICfiTES _.. HEAVY

DUlY

QUICK

WASH TOWELS

DRAIN SANITIZE

& SP_N

CLEAN WASHER with a,_r_h

POWER

Touch to turn the washer on and off. Touch to stop/cancel

a cycle at any time.

NOTE: Turning the Wash Cycle knob will also turn the

washer on and off.

WASH CYCLE KNOB

Turn the knob to select a cycle for your laundry load.

An LED will light up for the cycle selected.

NOTE: The Clean Washer LED will flash when the washer

has run 30 wash cycles as a reminder to run the Clean

Washer cycle.

See "Cycle Guide" for detailed descriptions of cycles.

_) START

Touch and hold until the light above START comes on to

start a cycle, or touch once while a cycle is in process to

pause it. If you want to add a garment, you can touch START

when the "Add Garment" LED is on.

DELAY WASH

Use + and - to delay the start of the wash cycle by up to

8 hours. To turn off Delay Wash, use + and - to set the delay

time to "0," or touch POWER.

LED DISPLAY AND SETTINGS

When you select a cycle, its default settings will light up and

the Estimated Time Remaining will be displayed. Factors

such as load size, wash temperature, and water pressure

may affect the time shown in the display during the cycle.

Tightly packing garments, unbalanced loads, or excessive

suds may cause the washer to adjust the cycle time, as well.

Touch the desired setting along the bottom of the display

to adjust. See "Cycle Guide" for available settings on each

cycle. Not all settings are available with all cycles.

Cycle Status Lights

For details, see the "Cycle Status Lights" section.

Wash Temp

The recommended wash temperature is preset for each

cycle. You may also select a wash temperature based

on the type of fabric and soils being washed. For best

results, follow the garment label instructions. All wash

temperatures feature a cold rinse.

Spin

This washer automatically selects the spin speed based

on the cycle selected. Some preset speeds can be

changed.

Faster spin speeds mean shorter dry times, but may

increase wrinkling in your load.

Slower spin speeds reduce wrinkling, but will leave

your load more damp.

Soil

The Soil setting (wash time) is preset for each wash

cycle. For most loads, use this preset soil level. When

you change the soil setting, the cycle time will increase

or decrease in the Estimated Time Remaining display.

For heavily soiled and sturdy fabrics, use the Soil setting

to select more wash time. For lightly soiled and delicate

fabrics, use the Soil setting to select less wash time.

Lower soil level settings will help reduce tangling and

wrinkling.

Presoak

Touch to add a Presoak to a wash cycle. Items will gently

tumble through the detergent and water to help loosen

tough stains.

OPTIONS

Touch to activate additional wash options or additional

features on the washer. Not all options are available on all

models.

_ Clean Boost with Steam

The Clean Boost with Steam option adds additional soak

and wash time to many cycles to help remove tough

stains, as well as a steam boost for added cleaning

power.

An integrated heater helps to maintain optimal wash

temperatures. See the "Cycle Guide" for cycles that

allow the Clean Boost with Steam option.

_ Extra Rinse

Activate this option to add an extra rinse to most cycles.

_ TumbleFreshTM Option

The TumbleFresh TM option will periodically tumble

the load after the end of the cycle for up to 6 hours

to reduce humidity. To turn on the TumbleFresh TM option,

touch TumbleFresh. If, however, the TumbleFresh TM

option is turned on, it will stay on for all future cycles

until turned back off - the washer remembers the last

on/off status set. To turn off the TumbleFresh TM option,

touch TumbleFresh.

You may also activate the TumbleFresh TM option without

running a cycle by touching and holding POWER for

one second, then touching and holding TumbleFresh

for 3 seconds, then touching and holding START for

3 seconds.

To turn off the TumbleFresh TM option when it is running,

touch POWER.

NOTE: The door will lock while the TumbleFresh TM option

is active. To cancel the option and unlock the door, touch

POWER.

_ Cycle Signal

Use this option to turn on or off the signal that sounds

at end of cycle.

To turn off the tones that sound when a setting is

touched: Touch and hold CYCLE SIGNAL for about

3 seconds. Repeat to turn them on.

_ Control Lock

Touch and hold for 3 seconds to lock the controls

to avoid unwanted changes or operation. Touch and

hold 3 seconds again to unlock. For each second

CONTROL LOCK is held down, the display will count

down one second: you will see "3," then "2," then "1 ."

You may still touch START to pause the cycle, or touch

POWER to turn off the washer.

_HE detergent

_ Liquid fabric

softener

_ Chlorine bleach

DISPENSER DRAWER

The dispenser drawer gives you the convenience of

automatically adding HE detergent, liquid chlorine bleach,

and liquid fabric softener to the wash load at the proper

time. See "Using the Dispenser Drawer" for information

on using the dispenser drawer.

_High Efficiency "HE" detergent compartment

This compartment holds liquid or powdered HE

detergent for your main wash cycle.

_ Liquid fabric softener compartment

Automatically dilutes and dispenses liquid fabric

softener at the optimum time in the cycle.

[] Use only liquid fabric softener in this dispenser.

_ Liquid chlorine bleach compartment

Automatically dilutes and dispenses liquid chlorine

bleach at the optimum time during the first rinse

after the wash cycle. This compartment cannot

dilute powdered bleach.

Choosing the Right Detergent

Use only High Efficiency detergents. The package will be marked

"HE" or "High Efficiency." Low-water washing creates excessive

sudsing with a non-HE detergent. Using non-HE detergent

will likely result in longer cycle times and reduced rinsing

performance. It may also result in component failure and, over

time, buildup of mold or mildew. HE detergents are low-sudsing

and quick-dispersing to produce the right amount of suds for

the best performance. They hold soil in suspension so it is not

re-deposited onto clean clothes. Follow the manufacturer's

instructions to determine the amount of detergent to use.

Use only High Efficiency (HE) detergent.

Control Panel and Features

Cycle Status Lights

Delay Wash

If a Delay Wash is set, the Delay Wash indicator will light and

the delay time will count down in the display.

Door Locked

Door Locked will light to indicate that the door is locked and

cannot be opened without first pausing or canceling the cycle.

Sensing

When START is touched, the washer will first perform a

self-test on the door lock mechanism and the sensing light

will come on. You will hear a click, the drum will make a partial

turn, and the door will click again as it unlocks briefly. The

door will click one more time when it locks again.

Once the door has locked the second time, the washer will

drain to calibrate the sensors; then it will begin tumbling and

adding water. The sensing process will continue throughout

the cycle. You may also hear water flowing through the

dispenser, adding detergent to the load.

After the load size is sensed, the estimated time based on

load size will be displayed. The actual cycle time may be

lengthened; however, the display will continue to show the

estimated time.

The sensing light will blink once a second at various times

during the cycle, such as when the washer is reducing extra

suds.

Add Garment

When "Add Garment" is lit, you may pause the washer, open

the door, and add items. Touch and hold START to start the

washer again.

Steaming

This will light to show that the cycle is using a steam boost for

added cleaning power.

Done

Once the cycle is complete, this light will come on. Remove

the load promptly for best results. The Done indicator is also

lit during the TumbleFresh 'Moption.

TumbleFresh TM option

The TumbleFresh 'Mindicator will light when the TumbleFresh 'M

option is active. During this time, the washer will occasionally

tumble the load.

Eco Monitor

The Eco Monitor allows you to see how the settings you select

affect your energy savings. To use the Eco Monitor, choose

the best cycle, temperature, spin speed, soil level, and options

for the fabrics being washed. The Eco Monitor will rate the

water and energy use of those selections, from Good to Best.

You can then adjust the settings and options to decrease the

amount of energy used within that cycle.

Using the Dispenser Drawer

1. Open the dispenser drawer.

2. Add laundry products as described in steps 4-6 in the "Using

Your Washer" section.

3. Slowly close the dispenser drawer. Make sure it is

completely closed.

NOTE: A small amount of water may remain in the dispensers

from the previous wash cycle. This is normal.

fAdding HE detergent to dispenser

Pour a measured amount of HE

detergent into detergent compartment.

For powdered detergent, lift the selector

to the high position. For liquid detergent,

push down the selector to the low

position.

Do not overfill; adding too much

detergent may cause detergent to be

dispensed into the washer too early.

HEdetergent

compartment

Use only High Efficiency

(HE)detergent.

Powdered detergent: Liquiddetergent:

Lift the selector to the high Push down the selector to

position, the low position.

IMPORTANT:

m Do not add single-dose laundry packet to dispenser

drawer.

m Use powdered detergent when using the Delay Wash

option. Liquid detergent may seep out before the wash

begins.

Cycle Guide

Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle, options, and settings

that best fit the load being washed. Not all settings are available with each cycle, and some options cannot be used together.

NOTE: All wash temperature selections feature a cold rinse.

using default

cycle settings:

Normally soiled

cottons, linens,

sheets, and mixed

garment loads

Heavily soiled white

fabrics and garments

Sturdy colorfast

fabrics and heavily

soiled garments

Sturdy towels and

wash cloths

Clothing, bedding,

and towels requiring

sanitization

No clothes in washer

il _ i i i i

Cycle:

Normal

Whites

Heavy

Duty

Towels

Sanitize

Clean

Washer

with

affresh ®

Wash

Temperature:

Extra Hot

Hot

Warm

Cool

Cold

Extra Hot

Hot

Warm

Cool

Cold

Extra Hot

Hot

Warm

Cool

Cold

Extra Hot

Hot

Warm

Cool

Cold

Extra Hot

Spin

Speed:

Extra Fast

Fast

Medium

Extra Fast

Fast

Medium

Slow

Extra Fast

Fast

Medium

Slow

Extra Fast

Fast

Medium

Slow

Extra Fast

Fast

Medium

Slow

sou

Level:

Extra Heavy

Heavy

Normal

Light

Extra Heavy

Heavy

Normal

Light

Extra Heavy

Heavy

Normal

Light

Extra Heavy

Heavy

Normal

Light

Extra Heavy

Heavy

Normal

Light

Available "

Options: Cycle Details:

Clean Boost

with Steam*

TumbleFresh TM

Extra Rinse

PreSoak

Delay Wash

Clean Boost

with Steam*

TumbleFresh TM

Extra Rinse

PreSoak

Delay Wash

Clean Boost

with Steam*

TumbleFresh TM

Extra Rinse

PreSoak

Delay Wash

Clean Boost

with Steam*

TumbleFresh TM

Extra Rinse

PreSoak

Delay Wash

Clean Boost

with Steam*

TumbleFresh TM

Extra Rinse

Delay Wash

TumbleFresh TM

Delay Wash

This cycle combines medium-

speed tumbling and an extra-

fast-speed spin. This cycle is

designed to provide the most

energy efficiency.

Uses a longer wash time with

fast-speed tumbling, extra

rinsing, and an extra-fast-speed

spin to provide optimal cleaning

and rinsing when bleach is

used.

Fast-speed tumbling and an

extra-fast-speed final spin help

provide optimal cleaning and

reduce drying times.

_ rovides fast-speed tumbling,

longer wash time, normal

rinsing, and an extra-fast-speed

spin to shorten drying time.

This cycle eliminates 99.99%

of the most common bacteria

found in clothes, sheets, and

towels. The extra hot wash

temperature ensures

sanitization. Check

recommended wash

temperature of your items.

Bacteria tested were

K. pneumonia, R aureginosa,

and S. aureus.

Use this cycle every 30 washes

to keep the inside of your

washer fresh and clean. This

cycle uses a higher water level.

Use with affresh®washer cleaner

tablet or liquid chlorine bleach to

thoroughly clean the inside of

your washer. This cycle should

not be interrupted. See "Washer

Care."

IMPORTANT: Do not place

garments or other items in the

washer during the Clean Washer

with affresh ®cycle. Use this

cycle with an empty wash tub.

See "Washer Care" in "Washer

Maintenance."

* The Clean Boost with Steam option is only available when a Warm, Hot, or Extra Hot water temperature is selected.

continued on next page

Cycle Guide

Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle, options, and settings

that best fit the load being washed. Not all settings are available with each cycle, and some options cannot be used together.

NOTE: All wash temperature selections feature a cold rinse.

Items to wash I

using default Wash Spin

cycle settings: Cycle: Temperature: Speed:

Wet load of clothes N/A

Swimwear, items

that need rinsing

Small loads of

2-4 lightly soiled

garments

Sheer fabrics,

lingerie, sweaters,

and lightly-soiled

shirts, blouses,

trousers, pants,

and skirts

Drain

& Spin

Drain

& Spin

with

Extra Rinse

Quick Wash

Delicates

Extra Hot

Hot

Warm

Cool

Cold

Extra Hot

Hot

Warm

Cool

Cold

Extra Hot

Hot

Warm

Cool

Cold

Extra Fast

Fast

Medium

Slow

Extra Fast

Fast

Medium

Slow

Extra Fast

Fast

Medium

Slow

Extra Fast

Fast

Medium

Slow

so, I Ava,ab eI

Level: Options= i Cycle Details:

N/A TumbleFresh T_ _ Use Drain & Spin to remove

Delay Wash _ excess water from the load,

Extra Heaw

Heavy

Normal

Light

Extra Heaw

Heavy

Normal

Light

TumbleFresh T_

Delay Wash

Clean Boost

with Steam*

TumbleFresh TM

Extra Rinse

PreSoak

Delay Wash

Clean Boost

with Steam*

TumbleFresh TM

Extra Rinse

PreSoak

Delay Wash

Extra Heaw

Heavy

Normal

Light

Spin speed can be set to a

slower setting.

Select Drain & Spin; then select

Extra Rinse to add water. The

cycle includes an extra-fast-

speed spin. For some fabrics,

you may wish to set the spin

speed to a slower setting.

For small loads (2-4 items)

needed quickly. This cycle

combines fast-speed tumbling,

a shortened wash time, and

an extra-fast-speed spin for

reduced drying times.

This cycle combines slow-

speed tumbling and slow-speed

spin for gentle fabric care and

reduced wrinkling.

Bright or darkly Cold Cold Extra Fast Extra Heaw TumbleFresh TM _ This cycle uses a concentrated

colored cottons, Wash Fast Heavy Extra Rinse _ detergent solution along with

linens, casual and Medium Normal Delay Wash cold water throughout the cycle

mixed loads Light to gently lift out stains and care

for fabrics.

* The Clean Boostwith Steam option isonly availablewhen aWarm, Hot, or Extra Hot water temperature is selected.

Load Size Recommendations

For best results, follow the load size recommendations noted for each cycle.

Q Small load: Fill the washer drum with 3-4 items, not more than 1/4 full.

_ edium load: Fill the washer drum up to about 1/2 full.

Large load: Fill the washer drum up to about 3/4 full.

Extra-large load: Fill the washer drum, but make sure clothes can tumble freely.

For best results, avoid packing tightly.

Using Your Washer

Fire Hazard

Never place items in the washer that are dampened

with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils),

Doing so can result in death, explosion, or fire.

First wash cycle without laundry

Before washing clothes for the first time, if not completed during

the final installation step, choose the QUICK WASH cycle and

run it without clothes. Use only HE detergent. Use 1/2 the

manufacturer's recommended amount for a medium-size load.

This initial cycle serves to ensure the interior is clean before

washing clothes.

1, Sort and prepare your laundry

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Add laundry products (if desired)

Single-dose laundry packet, Oxi-type boosters, color-safe

bleach, or fabric softener crystals can be added to the drum

prior to adding laundry.

NOTE: Do not add clothes to washer drum prior to adding

laundry products. Always follow manufacturer's instructions.

f3, Load laundry into washer

Sort items by recommended cycle, water temperature, and

colorfastness. Separate heavily soiled items from lightly soiled.

Separate delicate items from sturdy fabrics. Treat stains

promptly and check for colorfastness by testing stain remover

products on an inside seam.

iMPORTANT:

[] Empty pockets. Loose change, buttons, or any small object

can plug pumps and may require a service call.

[] Close zippers, fasten hooks, tie strings and sashes, and

remove non-washable trim and ornaments.

[] Mend rips and tears to avoid further damage to items

during washing.

[] Turn knits inside out to prevent pilling. Separate lint-takers

from lint-givers. Synthetics, knits, and corduroy fabrics will

pick up lint from towels, rugs, and chenille fabrics.

[] Do not dry garments if stains remain after washing, because

heat can set stains into fabric.

[] Always read and follow fabric care labels and laundry

product instructions. Improper usage may cause damage

to your garments.

-- -- E

Place a load of sorted clothes loosely in the washer. Items need

to move freely for best cleaning and to reduce wrinkling and

tangling. Close the washer door by pushing it firmly until the

latch clicks.

[] Depending on load type and cycle, the washer can be fully

loaded, but not tightly packed. Washer door should close

easily. See "Cycle Guide" for loading suggestions.

[] Mix large and small items and avoid washing single items.

Load evenly.

[] Wash small items in mesh garment bags. For multiple items,

use more than one bag and fill bags equally.

Using Your Washer

USING LAUNDRY PRODUCT DISPENSERS

NOTE: Do not add single-dose laundry packets, Oxi-type

boosters, color-safe bleach, or fabric softener crystals to

dispensers. They will not dispense correctly.

, Add liquid chlorine bleach to dispenser

I (if desired}

Adjust the selector, based on type of HE detergent used

(either liquid or powdered). See "Using the Dispenser

Drawer" instructions on how to use the dispenser.

(if desired}

Pour a measured amount of liquid fabric softener into liquid

fabric softener compartment. Always follow manufacturer's

directions for correct amount of fabric softener based on your

load size.

Fabric softener is always dispensed in the last rinse, even if

Extra Rinse is selected.

IMPORTANT: Do not overfill, dilute, or use more than 1/4 cup

(60 mL) of fabric softener. Do not fill past the MAX line.

Overfilling dispenser will cause fabric softener to immediately

dispense into washer.

[] Do not spill or drip any fabric softener onto the clothes.

[] Do not use liquid fabric softener dispenser balls in this

washer. They will not dispense correctly.

Add liquid chlorine bleach to the bleach compartment.

Do not overfill, dilute, or use more than 2/3 cup (165 mL).

Do not use color-safe bleach or Oxi in the same cycle with

liquid chlorine bleach.

[] Always measure liquid chlorine bleach. Use a measuring cup

with a pour spout; do not guess.

[] Do not fill beyond the "MAX" level. Overfilling could cause

garment damage.

7, Touch POWER to turn on washer

(optional}

Slowly close the dispenser drawer. Make sure the drawer is

closed completely, then touch POWER to turn on the washer

or go to Step 8.

8. Select CYCLE*

NORMAL

COLDWASH- -- WHITES

DEL_CATES -- HEAVY

DUTY

QU_CK

WASH TOWELS

DRAIN SANITIZE

& SPIN

CLEAN WASHER with _$_

Turn cycle knob to select your wash cycle. See "Cycle Guide"

for details on cycle features.

9. Adjust settings, if desired*

The display will show the default settings for the selected

cycle. To adjust a setting, touch its name - Wash Temp, Spin,

Soil, or Presoak. Adjusting settings will change the Estimated

Time Remaining. Tightly packing the load, unbalanced loads,

or excessive suds may also cause the washer to increase the

cycle time.

1 0. Select any additional options*

for_ut_,_Sr,_nJ

To add an option to the cycle, touch its name - Clean Boost

with Steam, Extra Rinse, TumbleFresh, or Cycle Signal. To

remove an option from the selected cycle, touch the option

again.

1 1. Setting a delayed wash

If you do not want to begin a cycle immediately, you may

choose the DELAY WASH option. This will delay the start

of the wash cycle by up to 8 hours.

To set a delayed wash:

1. Touch DELAY WASH + and - buttons to set the desired

delay time.

2. Touch and hold START to set the delay. The delay

countdown has started when the START light stops blinking.

*Not all options and settings are available with all cycles.

See "Cycle Guide" for available options and settings.

Using Your Washer

1 2. Touch and hold START to begin

wash cycle

Ho)d to Start

Touch and hold START to start the wash cycle. To pause a

cycle in progress, touch START once, then touch and hold

again to continue the cycle. To cancel a cycle, touch POWER.

Once you touch and hold START, you will hear the door lock,

unlock, and lock again. The washer door will remain locked

during the wash cycle.

Unlocking the door to add garments:

If you need to open the door to add 1 or 2

missed garments, you may do so while the

"Add Garment" light is lit.

@ Add Garment

Touch START once; the door will unlock

once the washer movement has stopped.

This may take several minutes. Then close

door and touch and hold START again to

restart the cycle.

Hold to Start

r'l-3. Remove garments promptly

after cycle is finished

for small items between the tub and the washer drum.

If you will be unable to remove the load [ _ i

promptly, use the TumbleFresh TM option.

( 1

If selected, the TumbleFresh TM option will

tumble the load periodically for up to 6 hours.

Toturn off the TumbleFresh TM option, touch POWER. To set the

washer so that the TumbleFresh TM option does not come on for

future cycles, touch TumbleFresh.

NOTE:

m The door will remain locked while the TumbleFresh _Moption

is active. To cancel the option and unlock the door, touch

POWER.

[] A small amount of water may remain in the dispensers after

the wash cycle is complete. This is normal.

[] This washer has a tight seal to avoid water leaks. To avoid

odors, leave the door open to allow the washer to dry

between uses.

Washer Maintenance

WATER iNLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Periodically inspect and replace inlet hoses

if bulges, kinks, cuts, wear, or leaks are found.

When replacing your inlet hoses, mark the date of

replacement on the label with a permanent marker.

WASHER CARE

Recommendations to Help Keep Your Washer Clean

and Performing at its Best

1. Always use High Efficiency (HE) detergents and follow the

HE detergent manufacturer's instructions regarding the

amount of HE detergent to use. Never use more than the

recommended amount because that may increase the

rate at which detergent and soil residue accumulate inside

your washer, which in turn may result in undesirable odor.

2. Use warm or hot water washes sometimes (not exclusively

cold water washes), because they do a better job of

controlling the rate at which soils and detergent accumulate.

3. Always leave the washer door slightly ajar between

uses to help dry out the washer and avoid the buildup

of odor-causing residue.

4. Clean residue from the underside of the glass window.

Cleaning Your Front Loading Washer

Read these instructions completely before beginning the

routine cleaning processes recommended below. This

Washer Maintenance Procedure should be performed,

at a minimum, once per month or every 30 wash cycles,

whichever occurs sooner, to control the rate at which soils

and detergent may otherwise accumulate in your washer.

Cleaning the Door Seal

1. Open the washer door and remove any clothing or items

from the washer.

2. Inspect the colored seal between the door opening and

the drum for stained areas or soil buildup. Pull back the

seal to inspect all areas under the seal and to check for

foreign objects.

3. If stained areas or soil buildup are found, wipe down

these areas of the seal using either of the following

two procedures:

a. affresh ®Grit Grabber TM Cloth Procedure:

i. When the cycle is complete, gently pull back the

rubber door seal and clean the entire surface with

the rough side of the Grit Grabber TM cloth.

b. Dilute Liquid Chlorine Bleach Procedure:

i. Mix a dilute bleach solution, using 3/4 cup (177 mL)

of liquid chlorine bleach and 1 gallon (3.8 L) of warm

tap water.

ii. Wipe the seal area with the dilute solution, using

a damp cloth.

iii. Let stand 5 minutes.

iv. Wipe down area thoroughly with a dry cloth and let

washer interior air dry with door open.

iMPORTANT:

[] Wear rubber gloves when cleaning with bleach.

[] Refer to the bleach manufacturer's instructions

for proper use.

F WASHER CARE (cont.)

Cleaning the inside of the Washer

This washer has a special cycle that uses higher water

volumes in combination with affresh ®Washer Cleaner or

liquid chlorine bleach to thoroughly clean the inside of the

washer. Steam washer models also utilize steam to enhance

cleaning inthis special cycle.

NOTE: Read these instructions completely before beginning

the cleaning process.

Begin procedure

1. Clean Washer with affresh ®Cycle Procedure

{Recommended for Best Performance):

ao Open the washer door and remove any clothing

or items.

bo Add an affresh ®Washer Cleaner tablet to the washer

drum.

co Do not add the affresh ®Washer Cleaner tablet

to the dispenser drawer.

d. Do not add any detergent or other chemical to the

washer when following this procedure.

eo Close the washer door.

fo Select the Clean Washer with affresh ®cycle.

g. On some models: Select the FanFresh®/TumbleFresh "_'

option to help dry the washer interior after the cycle

is complete. NOTE: The washer remembers your last

option selection and will use it for future wash cycles

until you deselect that option. While the fan is on,

the washer door will lock. To unlock the door, touch

POWER.

h. Touch and hold START to begin the cycle. The Clean

Washer with affresh ®Cycle Operation is described

below.

2. Chlorine Bleach Procedure:

ao Open the washer door and remove any clothing

or items.

bo Open the dispenser drawer and add liquid

chlorine bleach to the MAX level in both the bleach

compartment and the fabric softener compartment.

Either traditional or HE chlorine bleach can be used.

NOTE: Use of more liquid chlorine bleach than is

recommended above could cause washer damage

over time.

co Close the washer door and the dispenser drawer.

d. Do not add any detergent or other chemicals to the

washer when following this procedure.

eo Close the washer door.

fo Select the Clean Washer with affresh ®cycle.

g. On some models: Select the FanFresh®/TumbleFresh TM

option to help dry the washer interior after the cycle

is complete. NOTE: The washer remembers your last

option selection and will use it for future wash cycles

until you deselect that option. While the fan is on,

the washer door will lock. To unlock the door, touch

POWER.

h. Touch and hold START to begin the cycle. The Clean

Washer with affresh ®Cycle Operation is described

below.

NOTE: For best results, do not interrupt cycle.

Washer Maintenance

WASHER CARE (cont.)

Description of Clean Washer with affresh ®Cycle

Operation:

1. The Clean Washer with affresh ®cycle will determine

whether clothing or other items are in the washer.

2. If no items are detected in the washer, it will proceed

with the cycle.

a. If any items are detected in the washer, "rL" (remove

load) will be displayed. The door will unlock. Open

washer and remove any garments from the washer

drum.

b. Touch POWER to clear the "rL" code.

c. Touch and hold START to restart the cycle.

3. Steam models only: During the first 20 minutes of the

cycle, it will activate the steamer but the drum will not spin

or fill with water. You may see condensation on the door

glass during this initial phase. If you are using an affresh ®

Washer Cleaner tablet, it will not dissolve completely

during the steam phase. This is normal.

After the cycle is complete, leave the door open slightly to

allow for better ventilation and drying of the washer interior.

Cleaning the Dispensers

After a period of using your washer, you may find some

residue buildup in the washer's dispensers. To remove

residue from the dispensers, remove the drawer and wipe

the surfaces with a damp cloth and towel dry either before

or after you run the Clean Washer with affresh ®cycle. Use

an all-purpose surface cleaner, if needed.

IMPORTANT: Dispenser is not dishwasher safe.

Cleaning the Outside of the Washer

Use a soft, damp cloth or sponge to wipe up any spills.

Occasionally wipe the outside of your washer to help

keep it looking new. Use mild soap and water.

IMPORTANT: To avoid damaging the washer's finish, do not

use abrasive products.

CLEAN WASHER CYCLE REMINDER

NOTE: Not all models have the Clean Washer with affresh _

cycle reminder light.

The Clean Washer with _ -- X

affresh e_LED will flash at the

end of a wash cycle when

the washer has run 30 wash

cycles. This is a reminder to run the Clean Washer with

affresh e_cycle.

If the Clean Washer with affresh ®cycle is not turned on, the

LED will stop flashing at the end of a wash cycle after running

3 more regular wash cycles. After 30 more wash cycles are

completed, the Clean Washer with affresh® LED will again

flash at the end of a wash cycle as a reminder.

REMOVING THE DISPENSER

To remove:

1. Pull dispenser drawer out until it stops.

2. Press down on the release tab and pull straight out to

remove the dispenser.

--....

3. Lift off cover panel by

pulling straight up.

To replace:

1. Slide cover panel back

onto posts on dispenser.

2. Align edges of dispenser

with guides in washer,

then slide dispenser

back into slot.

NON=USE AND VACATION CARE

Operate your washer only when you are home. If moving,

or not using your washer for a period of time, follow these

steps:

1. Unplug or disconnect power to washer.

2. Turn off water supply to washer to avoid flooding due

to water pressure surges.

3. Clean the dispensers. See "Cleaning the Dispensers."

WINTER STORAGE CARE

iMPORTANT: To avoid damage, install and store washer

where it will not freeze. Because some water may stay in

hoses, freezing can damage washer. If storing or moving

during freezing weather, winterize your washer.

To winterize washer:

1o Shut off both water faucets, disconnect and drain water

inlet hoses.

2. Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum

and run washer on NORMAL cycle for about two

minutes to mix antifreeze and remaining water.

3. Unplug washer or disconnect power.

TRANSPORTING YOUR WASHER

1. Shut off both water faucets. Disconnect and drain water

inlet hoses.

2. If washer will be moved during freezing weather, follow

WINTER STORAGE CARE directions before moving.

3. Disconnect drain hose from drain system and from back

of washer.

4. Unplug power cord.

5. Place inlet hoses and drain hose inside washer drum.

6. Bundle power cord with a rubber band or cable tie to

keep it from hanging onto the ground.

IMPORTANT: Call for service to install new transport bolts.

Do not reuse transport bolts. Washer must be transported

in the upright position. To avoid structural damage to

your washer, it must be properly set up for relocation by a

certified technician.

f REINSTALLING/USING WASHER AGAIN

To reinstall washer after non-use, vacation, winter storage,

or moving:

1. Refer to Installation Instructions to locate, level, and

connect washer.

2. Before using again, run washer through the following

recommended procedure:

To use washer again:

1. Flush water pipes and hoses. Reconnect water inlet

hoses. Turn on both water faucets.

EJectrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug in washer or reconnect power.

3. Run washer through HEAVY DUTY cycle to clean washer

and remove antifreeze, if used. Use only HE detergent.

Use half the manufacturer's recommended amount for a

medium-size load.

Troubleshooting

First try the solutions suggested here or visit our website at www.whirlpool.com/product help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Once any possible issues are corrected, touch POWER once to clear the code. Reselect and restart the cycle.

"Sud" (Excess suds) Excessive suds in washer. Washer is

appears in display running a suds reduction routine.

Check for proper water supply.FC,8followed by EDI

(water supply error)

appears in display

FD£ followed by E5'

(drain pump system

error) appears in display

Check plumbing for correct drain

hose installation. Drain hose extends

into standpipe farther than 41/2''

(114 mm).

Allow the washer to continue. Use only HE detergent.

Always measure detergent, and base detergent quantity

on load size. Follow detergent manufacturer's instructions.

Both hoses must be attached and have water flowing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

Touch POWER once to clear the code. Then touch POWER

again to restart washer. If code appears again, call for service.

Check drain hose for proper installation.

Make sure the drain hose is not kinked, pinched, or blocked.

Remove any clogs from drain hose.

Use drain hose form and securely attach to drainpipe or tub.

Lower drain hose if the end is higher than 96" (2.4 m) above

the floor.

Use only HE detergent. Always measure detergent and follow

manufacturer's directions based on load size and soil level.

Not using HE detergent or using too

much HE detergent.

FC,5followed by En2 Washer door not locking. Touch POWER to cancel the cycle. Make sure the door is

(door will not lock) closed completely and latching. Check for items in the washer

appears in display drum that may be keeping the door from closing completely.

"rL" (remove load) Load detected in drum during Clean Remove items from washer drum and restart Clean Washer

appears in display Washer with affresh ®cycle, with affresh ®cycle.

Washer making error Door has not been opened and closed This code may appear when the washer is first turned on.

beeps for at least 3 cycles. Open and close the door to clear the display.

Washer beeps when Door not closed. Close the door completely.

START is touched

F## E## code other System error code. Touch POWER once to clear the code. Then touch POWER

than as described above again to restart washer. If code appears again, call for service.

appears in display

'qnt" (interrupted) The cycle was paused or cancelled. The washer can take 20 to 30 minutes to stop spinning and

appears in display drain and will display this error code during that time. Touch

POWER once to clear the code. Then touch POWER again to

restart washer.

The washer has run 30 wash cycles

and is indicating a reminder to run the

Clean Washer with affresh ®cycle.

Clean Washer LED

flashing at end of wash

cycle

Run the Clean Washer with affresh ®cycle. If the Clean Washer

with affresh ®cycle is not turned on, the LED will stop flashing

at the end of a wash cycle after running 3 more regular wash

cycles. After 30 more wash cycles are completed, the Clean

Washer LED will again flash at the end of a wash cycle as a

reminder.

Troubleshooting

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

mfyou experience

Vibration, rocking, or

"walking"

Feet may not be in contact with the

floor and locked.

Washer may not be level.

Load could be unbalanced

or too large.

The shipping bolts are still in the

back of the washer.

Front and rear feet must be in firm contact with floor, and washer

must be level to operate properly. Jam nuts must be tight

against the bottom of the cabinet.

Check floor for flexing or sagging. If flooring is uneven, a 3/4"

(19 mm) piece of plywood under your washer will reduce sound.

See "Level the Washer" in Installation Instructions.

Avoid tightly packing the load. Avoid washing single items.

Balance a single item such as a rug or jeans jacket with a

few extra items.

Item or load not suitable for selected cycle. See "Cycle Guide"

and "Using Your Washer."

See "Remove transport bolts from washer" in the

Installation Instructions.

Clicking or metallic

noises

Gurgling or humming

Rolling or sloshing

and occasional clicking

(on slow-speed spin)

Door locking or unlocking.

Objects caught in washer

drain system.

Washer may be draining water.

Steel bails in the balancing system

are balancing the load.

The door will lock, unlock, and lock again. You will hear 3 clicks

after touching and holding START. This is normal.

Empty pockets before wasMng. Loose items such as coins

could fall between washer drum and tub or may block pump.

It may be necessary to call for service to remove items.

It is normal to hear metal items on clothing such as metal snaps,

buckles, or zippers touch against the stainless steel drum.

The pump may make a humming sound with periodic gurgling

or surging as final amounts of water are removed during the

spin/drain cycles. This is normal at certain stages of the cycle.

This is normal at certain stages of the cycle.

Check the following for Fill hoses not attached tightly. Tighten filFhose connection.

proper installation

Fill hose washers. Properly seat all four fiIFhose flat washers.

Drain hose connection. Check that the drain hose is properly secured to drainpipe or

laundry tub.

Check household plumbing for leaks Water can back up out of a clogged sink or drainpipe. Check

or clogged sink or drain, all household plumbing for leaks (laundry tubs, drain pipe,

water pipes, and faucets.)

Water or suds leaking Not using HE detergent or using too Only use HE detergent. Suds from regular detergents can

from door or rear of much HE detergent, cause leaking from the door or rear of cabinet. Always measure

cabinet detergent and follow manufacturer's directions based on your

load requirements.

Residue on door glass. Periodically clean the underside of the glass window to avoid

potential leaks.

Door opened during "Add Garment."

Load not completely

covered in water

Water level not visible on door or

does not cover clothes.

Water can drip off the inside of the door when the door is

opened after the start of a cycle.

This is normal for an HE front load washer. The washer senses

load sizes and adds the correct amount of water for optimal

cleaning.

Troubleshooting

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter,

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help =

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

mfyou experience

Possible Causes Solution

Washer won't run or fill,

washer stops working

Check for proper water supply.

Check proper electrical supply.

Normal washer operation.

Both hoses must be attached and have water flowing to

inlet valve.

Both hot and cold water faucets must be turned on.

Check that inlet valve screens have not become clogged.

Check for any kinks in inlet hoses, which can restrict water flow.

Plug power cord into a grounded 3=prong outlet.

Do not use an extension cord.

Ensure there is power to outlet.

Check electrical source or call an electrician to check if voltage

is low.

Reset a tripped circuit breaker. Replace any blown fuses.

NOTE: If problems continue, contact an electrician.

Door must be completely closed and latched for washer to run.

Washer will pause during certain phases of cycle.

Do not interrupt cycle.

The washer pauses for about 2 minutes during certain cycles.

Allow the cycle to continue. Some cycles feature periods of

tumbling and soak.

Washer may be stopped to reduce suds.

Cold Wash uses less water in the beginning of the cycle to

provide a high concentration of detergent for optimal cleaning

action. Following this concentrated tumbling, more water is

used to complete the wash.

During the first 20 minutes of the Clean Washer with affresh <*>

cycle, it will activate the steamer but the drum will not spin or fill

with water. You may see condensation on the door glass during

this initial phase. If you are using an affresh <*_Washer Cleaner

tablet, it will not dissolve completely during the steam phase.

This is normal.

The washer door is not firmly shut. The door must be closed during operation.

Washer not loaded as recommended.

Remove several items, rearrange load evenly in washer drum.

Close door and touch and hold START.

Do not add more than 1 or 2 additional items after cycle has

started to avoid tightly packing or unbalancing.

Do not add more water to the washer.

Troubleshooting

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

mfyou experience

Washer won't run or fill,

washer stops working

(cont.)

Washer not draining/

spinning, loads are

still wet

Door locked at end

of wash cycle

Door will not unlock

Incorrect or wrong

wash or rinse

temperatures

Not using HE detergent or using too

much HE detergent.

Door not opened between cycles.

Drain hose extends into standpipe

farther than 4.5" (114 mm).

Only use HE detergent. Suds from regular detergents can

slow or stop the washer. Always measure detergent, following

manufacturer's directions based on your load requirements.

To remove suds, cancel cycle. Select DRAIN & SPIN with Extra

Rinse. Touch and hold START. Do not add more detergent.

The drain hose is clogged, or the

end of the drain hose more than

96' (2.4 m) above the floor.

The drain hose fits too tightly The drain hose should be loose yet fit securely. Do not seal the

in the standpipe, or is it taped drain hose with tape. The hose needs an air gap. See "Secure

to the standpipe, the Drain Hose" in Installation Instructions.

Using cycles with a slower spin Cycles with slower spin speeds remove less water than cycles

speed, with fast spin speeds. Use the recommended cycle/speed spin

for your garment.

Washer not loaded as recommended.

The load may be out of balance.

Not using HE detergent or using too

much HE detergent.

Small items may have been caught

in the pump or stuck between the

washer drum and the outer tub.

Water remaining in washer after cycle.

TumbleFresh Moption is on.

Door locks when cycle has started.

Check for proper water supply.

Washing many loads.

After 3 wash cycles in a row are completed, the door must be

opened and then closed before a new cycle can begin.

Check drain hose for proper installation. Use drain hose form

and securely attach to drainpipe or tub. Do not tape over drain

opening.

Lower drain hose if the end is higher than 96' (2.4 m) above

the floor. Remove any clogs from drain hose. See "Installation

Requirements" in Installation Instructions.

A tightly packed or unbalanced load may not allow the washer

to spin correctly, leaving the load wetter than normal. See

"Cycle Guide" for load size recommendation for each cycle.

Avoid washing single items. Balance a single item such as a rug

or jeans jacket with a few extra items.

Use only HE detergent. Suds from regular detergent or using too

much detergent can slow or stop draining or spinning. Always

measure and follow manufacturer's directions for your load.

To remove extra suds, select DRAIN & SPIN with Extra Rinse.

Do not add detergent.

Check the drum for any items sticking through the drum holes.

Empty pockets and use garment bags when washing small

items.

Select DRAIN & SPIN to remove any water remaining in the

washer. The washer door will unlock at the end of the drain.

While this option is on, the load is tumbled periodically for up

to 6 hours. The door remains locked during this time. To unlock

the door, cancel the option by touching POWER.

If the "Add Garment" light is lit, touch START once. The door

will unlock.

Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached to both washer and faucet, and

have both hot and cold water flowing to inlet valve.

Check that inlet valve screens are not clogged.

Remove any kinks in hoses.

Your hot water tank may not have enough hot water to keep up

with the number of hot or warm washes. This is normal.

Troubleshooting

f First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

Desired setting or

option does not light

Load not rinsed

Load is wrinkled,

twisted, or tangled

......Not cleaning or

removing stains

For best performance, not all

settings are available with each cycle,

and some options cannot be used

together.

Check for proper water supply.

Not using HE detergent or using too

much HE detergent.

Washer not loaded as recommended.

The load may be out of balance.

See the "Cycle Guide" for the available settings and options for

Add only 1 or 2 garments after washer has started.

Not using HE detergent or using too Use only HE detergent. Always measure detergent and follow

much HE detergent, manufacturer's directions based on load size and soil level.

Hard water or high level of iron (rust) You may need to install a water softener and/or iron filter.

in water.

Fabric softener dispensing ball used. Dispensing balls will not operate correctly with this washer.

Add liquid fabric softener to the fabric softener compartment.

Powdered detergent used for Consider using liquid detergent.

_. slow-speed cycle, j

Wash action too long for load. Select a lower soil level. Note that items will not be cleaned

as deeply as when using a higher soil level.

Spin speed too fast for load. Select a slower spin speed. Note that items will be wetter than

when using a faster speed spin.

The washer is not unloaded promptly. Unload the washer as soon as it stops or use the

TumbleFresh Moption if you will not be able to unload the

washer at the end of the cycle.

Not choosing the right cycle for the Use the Delicates cycle or another cycle with a slow spin

load being washed, speed to reduce wrinkling.

The wash water was not warm If safe for load, use warm or hot wash water.

enough to relax wrinkles.

Washer not loaded as recommended.

Make sure hot and cold inlet hoses are not reversed.

Both hoses must be attached and have water flowing to the

inlet valve.

Both hot and cold water faucets must be on.

Inlet valve screens on washer may be clogged.

Remove any kinks in the inlet hose.

The suds from regular detergent can cause the washer

to operate incorrectly.

Use only HE detergent. Always measure detergent and follow

manufacturer's directions based on load size and soil level.

Avoid tightly packing tm_ewasher. The washer will not rinse well

if tightly packed. Load with dry items only. See the "Cycle

Guide" for load size recommendations for each cycle.

Use cycle designed for the fabrics being washed.

Add only 1 or 2 garments after washer has started.

When load unbalance occurs, a washing process will start

to redistribute the load. This may lengthen the cycle time.

Avoid washing single items. Balance a single item such as

a rug or jeans jacket with a few extra items.

Add load loosely. Items need to move freely reduce

wrinkling and tangling. See the "Cycle Guide" for load

size recommendations for each cycle.

Reduce tangling by mixing types of load items. Use the

recommended cycle for the type of garments being washed.

Add load loosely. Items need to move freely for best cleaning.

See the "Cycle Guide" for load size recommendations for each

cycle.

Washer not loaded as recommended.

each cycle.

La page charge ...

Whirlpool WFW8740DC1 Le manuel du propriétaire

Marque: Whirlpool

Modèle: WFW8740DC1

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WFW8740DC1 Owner's manual

Whirlpool WFW8740DC1 Le manuel du propriétaire

Whirlpool WFW8740DC1 Le manuel du propriétaire

dans d''autres langues

Documents connexes