LG TD-V70122E Le manuel du propriétaire

3828EL3006J

Safety Instructions 3

Installation Instructions 5

Exhaust Requirements And Maintenance 10

Appearance And Design 12

Operating Your Dryer 13

Additional Functions 16

Caring For Your Dryer 17

Additional Tips For Smart Use 20

Troubleshooting Guide 22

Technical Data 26

Warranty 27

Ultra Big Capacity Drum

The Kenmore Dryer has a large capacity.

Reduced drying time

Drying time is shortened by efficient air flow mechanism and

optimized heater.

Innovative Noise Reduction

Noise is reduced by optimized design of air flow system and

vibration reduction technology.

Ease of Use

Large LED display and electronic control.

Your dryer provides sensor drying and manual drying programs.

Sensor Dry Dryer electronically senses laundry moisture level and it automatically determines operation time

based on the dryness of the load and the selected program. At times,you can see sudden increase or

decrease of operation time. It happens because a sensor will detect laundry humidity with a certain period.

Sudden change of operation time is not a malfunction.

Manual Dry Manual Dry allows you to set operation time manually to complete drying. Or use Manual Dry if

clothes are still damp after sensor dry cycle is finished. Manual Dry is more effective for heavyweight and bulky

items such as king-size bed sheets and thick work clothes.

What are Sensor Dry and Manual Dry?

2

C

F

ontents

F

eatures

Safety Instructions

3

S

F

afety Instructions

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

1)Read all instructions before using the appliance.

2)Do not dry articles that have come into contact with

gasoline, dry-cleaning solvents, or other flammable

or explosive substances, as they give off vapors

that could ignite or explode.

3)Do not allow children to play on or in the appliance.

Close supervision of children is necessary when

using the appliance.

4)Before the appliance is removed from service or

discarded, remove the door to the drying

compartment.

5)Do not reach into the appliance if the drum is

rotating.

6)Do not install or store this appliance where it will be

exposed to the weather.

7)Do not tamper the with the controls.

8)Do not repair or replace any part of the appliance or

attempt any servicing unless specifically

recommended in the user-maintenance instructions.

9)Do not use heat to dry articles containing foam

rubber or similarly textured rubber-like materials.

10)Clean lint screen before or after each load.

11) Keep area around the exhaust opening and

adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

12)The interior of the appliance and exhaust duct

should be cleaned periodically by qualified service

personnel.

13)Do not place items exposed to cooking oils in your

dryer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause

a load to catch fire.

14)Do not use fabric softners or products to eliminate

static unless recommended by the manufacturer of

the fabric softner or product.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of

malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least

resistance for electric current. This appliance is

equipped with a cord having an equipment-grounding

conductor and a grounding plug. The plug must be

plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local

codes and ordinances.

WARNING - Improper connection of the equipment-

grounding conductor can result in a risk of electric

shock. Check with a qualified electrician or service

person if you are in doubt as to whether the appliance

is properly grounded.

Do not modify the plug provided with the appliance: if

it will not fit the outlet, have a proper outlet installed by

a qualified electrician.

This appliance must be connected to a grounded

metal, permanent wiring system or an equipment-

grounding conductor must be run with the circuit

conductors and connected to the equipment-

grounding terminal or lead on the appliance.

WARNING!

To help reduce any risk of electric shock, fire, or other personal injury or property

damage when using your dryer, please exercise care and follow basic safety

precautions, including the following:

!

4

Safety Instructions

S

F

afety Instructions

To reduce the risk of fire or explosion, electric

shock, property damage, personal injury, or death

when using this appliance, please follow all

instructions and information, including those in

this manual and instructions provided by your

gas supplier.

• Do not store or use any gasoline, dry-cleaning

solvents any other flammable vapors or

liquids in the area surrounding this appliance.

• Do not dry anything that has ever had anything

flammable on it, even after washing.

• No washer can completely remove oil. Do not

dry any articles that have ever had any kind of

oil on them, including cooking oil.

• Articles containing foam, rubber, rubber-like

materials, plastic or similar materials should be

air dried.

• Failure to follow these instructions can result in

fire, death or serious injury.

• A qualified service person or company must

perform installation and service of this

appliance.

WARNING!

• Keep flammable materials and vapors, such

as gasoline, away from dryer.

• Place dryer at least 18 inches above the floor

for a garage installation.

• Failure to do so can result in death,

explosion or fire.

!

WARNING

!

5

Installation Instructions

Closet door

ventilation

hole

Closet side view





 







 



 



 





 



 



 

Closet Front view





 



 





 





 



 

I

F

nstallation Instructions

Built in

The following instructions will help guide you through the initial steps of setting up your dryer for use.

Please note that every section of this manual provides important information regarding the preparation

and use of your dryer, and it is important that you review this entire manual before proceeding with any

installation or use. More detailed instructions concerning electrical connections, gas connections, and

exhaust requirements are provided in other parts of this manual.

Choose a location with a solid floor for your dryer.

Place the dryer at least eighteen inches above the

floor for a garage installation. After placing the

dryer in the desired location, please make sure that

it has the required clearances shown below and

sections on Exhaust and Maintenance requirements,

page10.

Certain minimum clearances are required

above, behind, and to the sides of the unit, as

shown below. Those required minimum clearances

are set forth in the picture below. Please keep the

following instructions in mind when installing in a

closet or recessed area:

• Consider allowing additional clearance for

installation and servicing.

• Wall, door, and floor molding may force additional

clearances.

• An additional inch of clearance is recommended to

minimize noise transfer .

• Consider space needed for companion appliances.

• For closet installations, the picture below shows the

minimum required ventilation openings for the door.

A louvered door with comparable ventilation openings

is also acceptable.

STEP 1 Positioning the Dryer.

Leveling legs should be secured.

All four legs are stably placed on the solid and

even floor.

If dryer is not level, laundry may not tumble

properly and sensor will not detect the accurate

humidity information.

When leveling, please be cautious not to injure

your fingers and toes.

Note

* Most installations require a minimum 5 1/2 in.

(14 cm) clearance behind the dryer for the exhaust

vent with elbow.

6

Installation Instructions

1. Remove Duct Connector.

2. Remove the right (or left) Side Cap by (-) driver.

3. Assemble the Duct Connector to the hole and

close the back hole by the Side Cap.

• PLEASE BE AWARE THAT FAILURE TO

EXHAUST THE DRYER CORRECTLY WILL

VOID THE DRYER’S WARRANTY.

To change duct direction, follow these steps.

Duct Connector

Side Cap

I

F

nstallation Instructions

In addition to the following warnings, please refer to

manual section on Exhaust Requirements and

Maintenance, page 10.

IMPORTANT: To reduce the risk of fire, combustion,

and gas accumulation, the dryer must be vented to the

outdoors. Please follow the instructions (and all

others in this manual) very carefully.

WARNING!

• Use a heavy metal vent.

• Do not use plastic or thin foil duct.

• Failure to follow these instructions can

result in death or fire.

• Clean old ducts before installing this dryer

!

STEP 2 Connecting the Exhaust

and Venting System.

Vent end will face to the outside home and

improper taping and unstable installation of vent

will cause undesirable drying performance.

Note

• Do not use Plastic or thin foil duct.

• Use 4" (10.2 cm) diameter rigid or Semi-rigid

metal duct (note: venting materials are not

supplied with the dryer, and you should obtain the

venting materials necessary for proper installation)

• Position the Dryer so that the exhaust duct run is

as short as possible.

•

Clean old ducts before installing this dryer

• The male end of each section of exhaust duct must

point away from the dryer

• Use as few elbow joints as possible.

• Use duct tape on all duct joints

• Insulate ductwork that runs through unheated

areas in order to reduce condensation and lint

build-up on pipe walls.

During transportation side cap can come out slightly.

If that is so, push and fit it to the hole to prevent

possible lint leakage.

Note

7

Installation Instructions

Close the door to the dryer drum/drying

compartment and, after completing all steps in this

manual for proper installation of this dryer, start the

dryer on a heat setting, as described more fully in

the operating instructions that accompany the dryer.

The exhaust air or the exhaust pipe should be warm

after the dryer has been operating for three minutes.

The following instructions are applicable to

installations of the dryer in a manufactured or mobile

home. If you are uncertain whether your proposed

installation will comply with these standards, please

contact a service and installation professional for

assistance.

Following are several warnings and instructions

concerning making the electrical connection for

electric dryers.

The following instructions apply to any installation

of the dryer in a manufactured or mobile home:

1) Electric dryers may be vented to the outside

using the back, left, or right.

2) The dryer exhaust duct must be affixed securely

to the manufactured or mobile home structure,

and the exhaust duct must be made of a material

that will resist fire and combustion, and it is

recommended that you use a rigid or flexible

metal pipe.

3) Make sure the dryer has adequate access to

outside fresh air to ensure proper operation. The

opening for outside fresh air must be at least 25 in

(163)

4) It is important that the clearance of the duct from

any combustible construction be at least 2 inches

(5 cm), and, when venting the dryer to the

outdoors, the dryer can be installed with a

clearances of 1 inch (2.5 cm) at the sides and back

of the dryer.

5) DO NOT connect the exhaust duct with any other

duct, vent, chimney, or other exhaust duct.

6) Make sure the dryer has adequate access to outside

fresh air to ensure proper operation. The opening

for outside fresh air must be at least 25 in(163).

7) Please be aware that venting materials are not

supplied with the dryer. You should obtain the

venting materials necessary for proper installation.

Use power supply (Socket) rated 240Volts, 30

ampere.

I

F

nstallation Instructions

Prior to the first use of this appliance, use all-

purpose cleaning products or a solution of detergent

and water, with damp cloth to remove from the

inside of the dryer drum/drying compartment any

dust or dirt that may have accumulated inside the

dryer. Plug-in your dryer after reviewing the

following parts on your dryer’s Electrical

Requirements.

STEP 4

Preparation of the Dryer.

STEP 3 Electrical Plug Connections

STEP 5 Confirming Heat Source

Operation

STEP 6 Additional Instructions

for Installation of Your

Dryer in a Manufactured

or Mobile Home

WARNING!

DO NOT connect exhaust ducts with

metal screws or fasteners that extend

into the duct.

!

WARNING!

DO NOT vent the exhaust duct under the

manufactured or mobile home.

!

WARNING!

󳀏Do not plug with several other appliances power cord.

󳀏Do not grasp power cord or switch with wet hands.

󳀏Do not use damaged power cord, plug, and socket.

!

8

Installation Instructions

Stacking Kit

In order to stack this dryer on an Kenmore

washing machine(40002), an Kenmore stacking

kit is needed.

Installation Procedure

1. Place the Kenmore dryer on the Kenmore

Washing machine(40002).

2. Unscrew Rear cover in the Base by unscrewing

2 screws.

3. After detaching protection sheet of double-side

tape, align stacking kit holes rear cover holes

and then attach tape to the washer by pressing

hard.

4. Assemble a stacking kit as following.

• Screw 2 screws which is unscrewed earlier to

assemble dryer rear back and stacking kit.( )

• Use accessory screws to assemble washer rear cover

and stacking kit. ( , )

• The procedure for the opposite side will be the

same.

I

F

nstallation Instructions

WARNING!

!

Incorrect installation can cause serious

accidents.

The weight of the dryer and the height of

installation makes the stacking procedure

too risky for one person. This procedure

should be performed by 2 or more

experienced service personnel.

9

Installation Instructions

1.

Leveling the dryer is to prevent undesirable

noise and vibration.

2. Place your dryer in a solid and level area

where water is not dripping or freezing.

2.

If the dryer is not properly level, adjust the

levelling legs up and down as necessary.

2. Turn them clockwise to raise and

counterclockwise to lower until the dryer is not

wobbling both front-to-back and side-to-side.

󳀌

Diagonal Check

󳀌

When pushing down the edges of the machine, the

machine should not move up and down at all. (Please,

check both directions) If machine rocks when pushing

the machine top plate diagonally, adjust the feet again.

Level the dryer

I

F

nstallation Instructions

E

xhaust Requirements And Maintenance

10

Exhaust Requirements And Maintenance

Following are important instructions and information concerning the exhaust requirements for your dryer.

Important Warning: To reduce the risk of fire, combustion, or accumulation of combustible gases, DO

NOT exhaust dryer air into an enclosed and unventilated area, such as an attic, wall, ceiling, crawl space,

chimney, gas vent, or concealed space of a building. To reduce the risk of fire, DO NOT exhaust the dryer with

plastic or thin foil ducting.

Exhaust Requirements and Instructions:

1. Venting materials are not provided with the dryer and

you should obtain the necessary venting materials

locally. For example, the outer end of exhaust pipe

must have a weather hood with hinged dampers to

prevent back-draft when the dryer is not in use.

2. The exhaust duct must be four inches (10.2 cm) in

diameter with no obstructions. The exhaust duct

should be kept as short as possible. Make sure to

clean any old ducts before installing your new dryer.

3. Rigid or semi-rigid metal ducting is recommended for

use as transition ducting between the dryer and and the

wall. In special installations when it is impossible to

make a connection with the above recommendations,

then a UL-listed flexible metal transition duct may be

used between the dryer and wall connection only. The

use of this ducting will affect dry time.

4. DO NOT use sheet metal screws on exhaust pipe joints

or other fastening means which extend into the duct that

could catch lint and reduce the efficiency of the exhaust

system. Secure all joints with duct tape.

5. To maximize operating results, please observe the duct

length limitations noted in the chart above.

!

Number of 90°

Elbows

Weather Hood

Type

Recommended

Maximum length of 4”

(10.2 cm) diameter rigid

metal duct

Maximum length of 4”

(10.2 cm) diameter

flexible metal duct

NOTE : Deduct 6 feet (1.8 m) for each additional elbow.

It is not recommended to use more than 4 90° elbows.

Use Only for Short Run

Installations

0

1

2

3

4

0

1

2

3

4

65 feet (19.8 m)

55 feet (16.8 m)

47 feet (14.3 m)

36 feet (11.0 m)

28 feet (8.5 m)

45 feet (13.7 m)

35 feet (10.7 m)

30 feet (9.1 m)

25 feet (7.6 m)

20 feet (6.1 m)

55 feet (16.8 m)

47 feet (14.3 m)

41 feet (12.5 m)

30 feet (9.1 m)

22 feet (6.7 m)

35 feet (10.7 m)

27 feet (8.2 m)

21 feet (6.4 m)

17 feet (5.2 m)

15 feet (4.5m)

4”

(10.2 cm)

4”

(10.2 cm)

2-1/2”

(6.35 cm)

Exhaust Requirements And Maintenance

11

E

F

xhaust Requirements And Maintenance

Exhaust and Dryer Maintenance

1. After one year of use, the interior and complete

exhaust system of the dryer should be examined and

cleaned if necessary.

2. Before one year of use, when drying performance has

become unsatisfactory, please examine and clean the

exhaust duct for better drying performance.

3. Check the weather hoods frequently to ensure the

dampers are moving freely, that the dampers are not

pushed in and that nothing has been set against the

dampers.

4. A qualified service person or company should be used

to perform this maintenance.

5. A Flexible Metal Vent Kit, available at extra cost, can

be used to exhaust the dryer when it is placed in hard

to reach places. This Kit comes in two pieces, one of

which is attached to the dryer and the other is attached

to the wall exhaust outlet. Following attachment of the

two separate pieces to the dryer and the wall, the dryer

may be returned to its final position, after which the

two pieces themselves can be connected.

7. Ordinarily, the dryer drum will need no care. Wipe the

exterior of the dryer as required, and always wipe the

exterior of the dryer in the event any detergent, bleach,

or other washing products is spilled on the dryer.

8. Clean the control panel with a damp cloth as

necessary. Warning: spray pre-wash products may

damage the finish of the control panel.

9. Please clean the lint filter either before drying each

load or after drying each load.

10. Always make sure the lint filter is clean before

starting a new load, because a clogged lint filter may

increase drying times.

11. Annually remove the lint filter and attach it to the

vacuum duct. See item #2 above.

12. Please note that the wiring diagram is provided inside

the dryer control hood. Label all wires prior to

disconnection when servicing the dryer, because

wiring errors can cause serious injury to you and your

dryer.

Cleaning the Lint Screen

1. Clean the lint filter either before drying each load

or after drying each load. Always make sure the

lint filter is clean before starting a new load,

because a clogged lint filter may increase drying

times.

2. To clean, pull the lint screen straight up and roll

any lint off the screen with your fingers.

Do not rinse or wash screen to remove lint. Push

the lint screen firmly back into place.

3. Always ensure the lint screen is firmly secured

before running the dryer. Running the dryer with

a loose lint screen may cause overheating and

damage to the dryer and articles being dried.

4. Some articles of clothing may shed more lint than

others (towels for example), causing the Lint

Screen to rapidly fill. Remove lint from the lint

screen before and after drying these articles, such

as new towels.

5. In the event lint falls off of the lint screen and

into the dryer during removal, inspect the exhaust

hood and remove any lint.

6. Laundry detergent and fabric softener residue can

build up on the lint screen, causing longer drying

times. The screen is likely blocked if lint falls off

the screen. In order to prevent this type of build

up, and help ensure proper operation of your

dryer, clean the lint screen with a nylon brush

every six months or, if necessary, more

frequently. The lint filter can also be washed as

follows:

a) After rolling the lint off of the screen with your

fingers, wet both sides of the screen with hot or

warm water.

b) Wet a nylon brush with hot water and liquid

detergent and scrub the lint screen with the brush

to remove the buildup of detergent and fabric

softener.

c) After the residue has been removed, rinse screen

with hot water.

d) After drying the lint screen with a clean towel,

firmly replace the lint screen in your dryer.

WARNING!

Disconnect the dryer’s electric power

prior to any cleaning or maintenance.

!

Appearance And Design

12

Control Panel

Door

LED Display

󳀏Time Display

󳀏Indicator lamps

Additional

Function Buttons

󳀏Low Temp

󳀏Wrinkle care

󳀏Time Delay

󳀏Time Up( )

󳀏Time Down( )

Program Selector Start/Pause

Control Panel

Air Ventilation Grill

A

F

ppearance And Design

Operating Your Dryer

13

Cycle Selection Table

Bed linen and table linen, tracksuits,

blankets

Terry towelling, tea towels, towel,

bed linen

Bath towels, tea towels,

underwear, cotton socks

T-shirts, trousers, underwear,

work clothes

Bed linen, table linen, towels, T-shirts,

Polo shirts, and work clothes

Standard

Program

Very Dry

Normal

Damp Dry

Very Dry

Normal

Less Dry

Damp Dry

Delicate

Warm dry

Air dry

Mixed-Fabric cycles

(Note) Press the Low Temp. button for heat-sensitive items

Cotton (Whites and colors)

(Note) press the Low Temp. button for heat-sensitive items

Electronic Auto Dry Cycles

For thick and quilted fabrics which do not need to be ironed.

For fabrics which do not need to be ironed.shirts, blouses and sportswear

Trousers, dressers, skirts, blouses

For fabrics which do need to be ironed.

For thick and quilted fabrics which do not need to be ironed.

For fabrics which do not need to be ironed.

For fabrics which do need to be ironed lightly, not completely.

For fabrics which do need to be ironed.

All fabrics needing freshing, tumbles without heat

Manual dry Cycles for selected length of time

Special Fabrics

Silk, Women's thin clothes, lingerie For fabrics which are heat-sensitive like synthetic fabrics.

Small clothes & pre-dried laundry

Normal fabrics using hot temperature 40,minutes

Bath towels, bath robes, dishclothes,

Quilted fabrics made of acrylic

O

F

perating Your Dryer

WARNING!

!

If the load is less than 1kg, please use Manual Dry Course

Heat-sensitive fabrics including silk, underwears, lingerie should be used in Delicate courses.

Otherwise, these clothes can be damaged.

Important Warning: To reduce the risk of fire, electric shock, or injury to person, read this entire manual, including

the Important Safety Instructions, before operating this dryer.

14

Before first use of the dryer

Turn on.

Open the

Door.

Check the

lint filter.



Before you use the dryer for the first time, there are some points that you have to check.

After removing the dryer from the package, check the product has no problem and is properly installed.

1. Check the dryer is well balanced by using a level. In order to check this, you can see and adjust legs which are supposed to stay put.

2. Check major parts, such as the door control panel and drum.

3. Check the operation of the dryer by running it for 5 minutes to be sure it heats.

4. At the first use, there might be a slight odor as dust is burned off the heating element. Leave the door open and it will dissipate.

1.

Turn the power on.

First, press the Power button. The indicator light above

the button will become illuminated indicating that the

machine is all set to run.

4.

Place laundry into the drum after

sorting.

The clothes should be sorted by fabric type and

dryness level. All the strings and belts of clothes

should be well tied and fixed before being put into

the drum. It is desired that you push laundry all the

way back to keep it away from the door seal. If not,

door seal and clothes may be damaged.

3.

Check the lint filter.

The lint filter near the door should be emptied after or

before drying operation. Open the door and check if lint

filter is cleaned. If not, clean it.

2.

Open the door.

Operating Your Dryer

O

F

perating Your Dryer

Be careful not to put buttons, small laundry, and any

kind of small items into the holes below the door

Note

15

Operating Your Dryer

Select the

desired

cycle.

Take out

the laundry.

Clean the

door lint

filter.

5. Close the Door.

Before you close the door, make sure fabrics are well

placed inside and that foreign objects are not caught

around door.

6. Select the Drying Cycle you want.

You can choose a cycle by turning the program

control knob until the required program reaches to

its indicator. If you only press the Start/Pause button

without choosing any cycle, the dryer will proceed

with the standard program. [ Please refer to

following Cycle Selection table (page 13) for

detailed information ]

8. After operation is completed, open

the door and remove the laundry.

Careful! The drum inside could be still hot.

(Operation time varies depending on your cycle

selection or options.)

9. Clean the Lint Filter.

The lint filter should be cleaned after each load.

10. Turn off the Dryer.

Press the Power button.

7. Press the Start button.

You can hear drum rotating.

O

F

perating Your Dryer

- Be careful the filter isn’t torn when using a

vaccum cleaner. If there is a little residue buildup

on filter, you can scrub the lint screen with a soft

brush to remove.

- If you want to open the door while dryer is

operating, press the Start/Pause button first, wait

until drum completely stops and then open the

door.

Note

Additional Functions

16

Low Temp.

Low temp is functioning to decrease dry

temperature.

Wrinkle care

Wrinkle care is functioning to prevent creases

and rumples that are formed when the laundry

is not unloaded promptly at the end of drying

cycle. In this function, the dryer repeatedly runs

and pauses to the cycle end.

If the door is open during Wrinkle care process,

this function is cancelled. If the door is opened

during normal operation without selecting

Wrinkle care, this function will be remembered

and processed.

Time Delay

You can use the Time Delay function to

delay the finishing time of drying cycle.

Maximum Time Delay is 19 hours.

1. Turn the dryer on

2. Select cycle

3. Set time delay hour

4. Press Start/Pause button

Child Lock

For the safety of your children, press Low

Temp. and Wrinkle care buttons at the same

time for about 3 seconds. You can check this

function by seeing the dryer display on

LED window.

A

F

dditional Functions

Caring For Your Dryer

17

Clean filter

This lamp blinks at the start of each use just to remind

you to clean the filter.

1. Open the door.

2. Pull the filter

out.

3. Clean the filter

by using a

vacuum cleaner

or rinsing under

the tap.

Care and Cleaning is

It’s not very difficult to care for your dryer. All you

have to do is to follow the information below.

Clean Lint Filter

Clean lint filter after each use and check it before each

use. It should also be cleaned if the Clean Filter light

lights and the buzzer sounds during operation of the

dryer: Cleaning or emptying the filter will reduce

drying times and energy consumption and lengthen

the dryer life.

4. Replace the

filter.

- Push the

filter all the

way down to

avoid

Interference

with the

door.

Moisture Sensor

This device senses the moisture remaining in the

laundry during operation, which means it must be

cleaned all the time. The main reason of cleaning

this part is to remove the build-up of lime scale on

the surface of sensor. Wipe the sensors inside drum

(shown in the picture).

5. Close the door.

C

F

aring For Your Dryer

In the case you wash the lint screen using water,

dry it thoroughly.

Note

18

Reverse the door

The door can be reversed to fit to your own

installation conditions. From the factory, the door

hinge is located on the right side.

4. Detach both

hinge point

covers.

5. Unscrew two

door hinges.

6. Replace both

hinge point

covers where

door hinge is

located.

7. Replace the

door catch to

the reverse

location.

8. Tighten the

screws in the

door hinges.

2. Remove the

door lock

cover.

1. Unscrew the

bottom hinge of

the door first

and top hinge.

And then place

on the blanket

to prevent

scratches.

3. Remove the

door lock and

replace where

door lock

cover is

located.

Caring For Your Dryer

C

F

aring For Your Dryer

1. This work may cause the injury of your hands

so you must be careful to handle some sharp

devices like torx screwdriver or slotted

screwdriver.

2. When the door is revered, the hand sticker on

the door also must be replaced.

Do not use an electric screwdriver.

Note

19

Caring For Your Dryer

Change the Bulb

The bulb itself could be very hot when the dryer just

finishes its operation. So before changing the bulb,

be sure that the inside of the drum is cool down.

1. Open the door, put a hand into the drum and

grasp the bulb cover.

2. With bulb held by hand gently, turn the bulb cover

clockwise.

5. Replace in the new bulb in the reverse

unscrewing direction.

3. Sepearate the bulb cover from the socket

housing.

4. Remove the current bulb turning it to Counter

clockwise. Be careful that it does not fall off.

C

F

aring For Your Dryer

No any special tool is needed for this work.

All steps can be done by hand.

Note

WARNING!

Power cord must be unplugged before this

work to avoid danger of electric shock.

!

Additional Tips For Smart Use

20

Below are fabric care labels.

Woven and Knit Materials

Some woven and Knit materials may shrink,

depending on their quality.

Permanent Press and Synthetics

Do not overload your dryer.

Take out permanent press article as soon as the

dryer stops to reduce wrinkles.

Baby Clothes and Night Gowns

Always check the manufacturer’s instructions.

Rubber and Plastics

Do not dry any items made from or containing

rubber or plastics such as:

a) Aprons, bibs, and chair covers

b) Curtains and table clothes

c) Bathmats

Fiberglass

Do not dry fiberglass articles in your dryer.

Glass particles left in the dryer could be picked up

by your clothes the next time you use the dryer and

irriate your skin.

Fabric Care Labels

Clothes have its own wash care labels so drying

according to wash care labels is recommended.

Not only that, the laundry must be sorted according

to size and fabric type.

Do not overload in order to save you energy, time

and best dry performance.

Drying Guide

A

F

dditional Tips For Smart Use

Symbols Instructions

Dry

Tumble dry

Permanent Press /

Wrinkle resistant

Gentle / Delicate

Do not tumble dry

Do not dry

High heating

Medium heating

Low heating

No heat / air

Line Dry / hang to dry

Drip dry

Dry flat

In the shade

La page charge ...

LG TD-V70122E Le manuel du propriétaire

Ce manuel convient également à

LG TD-V70122E Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents