Blodgett DFG-50 Mode d'emploi

Marque: Blodgett

Modèle: DFG-50

Taper: Mode d'emploi

DFGĆ50

CONVECTION OVEN

INSTALLATION - OPERATION - MAINTENANCE

DFGĆ50

FOURS À CONVECTION

MANUEL D'INSTALLATION - FONCTIONNEMENT - ENTRETIEN

BLODGETT OVEN

www.blodgett.com

44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone: (802) 658Ć6600 Fax: (802)864Ć0183

PN 17355 Rev R (8/10)

E 2010 - G.S. Blodgett Corporation

IMPORTANT

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors or liquids in the vicinity

of this or any other appliance.

AVERTISSEMENT

Ne pas entreposer ni utiliser de l'essence ni d'autres vapeurs ou liquides inflamĆ

mables dans le voisinage de cet appariel, ni de tout autre appareil.

INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE USER SMELLS GAS

MUST BE POSTED IN A PROMINENT LOCATION. THIS INFORMATION MAY BE

OBTAINED BY CONTACTING YOUR LOCAL GAS SUPPLIER.

LES INSTRUCTIONS À RESPECTER AU CAS OÙ L'UTILISATEUR PERÇOIT UNE

ODEUR DE GAZ DOIVENT ÊTRE AFFICHÉES DANS UN ENDROIT BIEN VISIBLE.

VOUS POUVEZ VOUS LES PROCURER AUPRÈS DE VOTRE FOURNISSEUR DE

GAZ LOCAL.

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR

MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE

INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY

BEFORE INSTALLING OR SERVICING THIS EQUIPMENT

AVERTISSEMENT: UNE INSTALLATION, UN AJUSTEMENT, UNE ALTÉRATION, UN

SERVICE OU UN ENTRETIEN NON CONFORME AUX NORMES PEUT CAUSER DES

DOMMAGES À LA PROPRIÉTE, DES BLESSURES OU LA MORT. LISEZ ATTENTIVEĆ

MENT LES DIRECTIVES D'INSTALLATION, D'OPÉRATION ET D'ENTRETIEN AVANT

DE FAIRE L'INSTALLATION OU L'ENTRETIEN DE CET ÉQUIPEMENT.

The information contained in this manual is important for the proper installation,

use, and maintenance of this oven. Adherence to these procedures and instrucĆ

tions will result in satisfactory baking results and long, trouble free service.

Please read this manual carefully and retain it for future reference.

Les informations données dans le présent manuel sont importantes pour installer,

utiliser et entretenir correctement ce four. Le respect de ces instructions et procéĆ

dures permettra d'obtenir de bons résultats de cuisson et une longue durée de serĆ

vice sans problèmes. Veuillez lire le présent manuel et le conserver pour pouvoir

vous y reporter à l'avenir.

Errors: Descriptive, typographic or pictorial errors are subject to correction. SpecificaĆ

tions are subject to change without notice.

Erreurs:Les erreurs de description, de typographie ou d'illustration font l'objet de

corrections. Les caractéristiques sont sujettes à modifications sans préavis.

THE REPUTATION YOU CAN COUNT ON

UNE RÉPUTATION SUR LAQUELLE VOUS POUVEZ COMPTER

For over a century and a half, The Blodgett Oven Company has been building

ovens and nothing but ovens. We've set the industry's quality standard for all

kinds of ovens for every foodservice operation regardless of size, application

or budget. In fact, no one offers more models, sizes, and oven applications

than Blodgett; gas and electric, fullĆsize, halfĆsize, countertop and deck, conĆ

vection, Cook'n Hold, CombiĆOvens and the industry's highest quality Pizza

Oven line. For more information on the full line of Blodgett ovens contact your

Blodgett representative.

Cela fait maintenant dessus un siècle et demi que Blodgett se spécialise dans

la fabrication de fours. Nous avons établi les normes de qualité qui s'appliĆ

quent dans l'industrie à tous les types de fours utilisés dans les services aliĆ

mentaires, quel qu'en soit la taille, l'exploitation ou le budget. En fait, ni n'offre

plus de modèles, de tailles et d'applications de fours que Blodgett. À gaz et

électriques. De tailles différentes, sur plan de travail et superposables. Qu'il

s'agisse de fours à convection, des modèles Cook'n Hold et CombiĆOven, ou

de la gamme de fours à pizzas de la plus haute qualité offerte sur le marché.

Pour de plus amples informations sur la gamme complète de fours Blodgett,

veuillez contacter votre représentant Blodgett.

Your Service Agency's Address:

Adresse de votre agence de service:

Model/Modèl:

Serial Number/Numéro de série:

Your oven was installed by/

Installateur de votre four:

Your oven's installation was checked by/

Contrôleur de l'installation de votre four:

Table of Contents/Table des Matières

Introduction

Oven Description and Specifications 2. . . .

Oven Components 3. . . . . . . . . . . . . . . . . . . .

Installation

Delivery and Location 4. . . . . . . . . . . . . . . . .

Stand Assembly 5. . . . . . . . . . . . . . . . . . . . . .

Oven Assembly 7. . . . . . . . . . . . . . . . . . . . . .

Oven Assembly to Stand 7. . . . . . . . . . . . .

Leg Attachment 8. . . . . . . . . . . . . . . . . . . . .

Oven Leveling 8. . . . . . . . . . . . . . . . . . . . . .

Ventilation 9. . . . . . . . . . . . . . . . . . . . . . . . . . .

Canopy Type Exhaust Hood 9. . . . . . . . . .

Direct Flue Arrangement 10. . . . . . . . . . . . .

Utility Connections - Standards and

Codes 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Gas Connection 12. . . . . . . . . . . . . . . . . . . . . .

Electrical Connection 15. . . . . . . . . . . . . . . . .

Initial Startup 16. . . . . . . . . . . . . . . . . . . . . . . . .

Operation

Safety Information 17. . . . . . . . . . . . . . . . . . . .

Solid State Manual Control 18. . . . . . . . . . . . .

Solid State Digital Control 19. . . . . . . . . . . . . .

Pulse Plus 21. . . . . . . . . . . . . . . . . . . . . . . . . . .

Cook and Hold Control 22. . . . . . . . . . . . . . . .

CHĆPro3 (Solid State Programmable

Digital Control) 24. . . . . . . . . . . . . . . . . . . . . . .

Blodgett IQ2T Vision Control 27. . . . . . . . . .

How Cook and Hold Works 37. . . . . . . . . . . .

General Guidelines for Operating

Personnel 38. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Suggested Times and Temperatures 39. . . .

Maintenance

Cleaning and Preventative Maintenance 40.

Troubleshooting Guide 41. . . . . . . . . . . . . . . .

Introduction

Description et Spécifications du Four 42. . . .

Éléments du Four 43. . . . . . . . . . . . . . . . . . . . .

Installation

Livraison et Implantation 44. . . . . . . . . . . . . . .

Montage du bâti 45. . . . . . . . . . . . . . . . . . . . . .

Montage du Four 47. . . . . . . . . . . . . . . . . . . . .

Assemblage du Four sur le Socle 47. . . . .

Pose des Pieds 48. . . . . . . . . . . . . . . . . . . . .

Mise à Niveau du Four 48. . . . . . . . . . . . . . .

Ventilation 49. . . . . . . . . . . . . . . . . . . . . . . . . . .

Hotte D'évacuation Type Voûte 49. . . . . . .

En Prise Directe 50. . . . . . . . . . . . . . . . . . . . .

Branchements de Service -

Normes et Codes 51. . . . . . . . . . . . . . . . . . . . .

Branchement de Gaz 52. . . . . . . . . . . . . . . . .

Raccordement Électrique 55. . . . . . . . . . . . . .

Mise en Marche Initiale 56. . . . . . . . . . . . . . . .

Utilisation

Informations de Sécurité 57. . . . . . . . . . . . . . .

Commandes à SemiĆConducteurs 58. . . . . .

Commandes Numériques à

SemiĆConducteurs 59. . . . . . . . . . . . . . . . . . . .

Pulse Plus 62. . . . . . . . . . . . . . . . . . . . . . . . . . .

Commande Cuisson et Maintien 63. . . . . . . .

CHĆPro3 (Commande Numérique

Programmable pour SemiĆConducteurs) 65.

Blodgett IQ2T Commande Vision 69. . . . . .

Principe de la Fonction de Cuisso

et Maintien 80. . . . . . . . . . . . . . . . . . . . . . . . . . .

Consignes Générales à l'Intention

des Utilasateurs 81. . . . . . . . . . . . . . . . . . . . . .

Durées et Températures Suggérées 82. . . . .

Entretien

Nettoyage et Entretien Préventif 83. . . . . . . .

Guide de Détection des Pannes 84. . . . . . . .

Introduction

Oven Description and Specifications

Cooking in a convection oven differs from cooking

in a conventional deck or range oven since heated

air is constantly recirculated over the product by

a fan in an enclosed chamber. The moving air conĆ

tinually strips away the layer of cool air surroundĆ

ing the product, quickly allowing the heat to peneĆ

trate. The result is a high quality product, cooked

at a lower temperature in a shorter amount of time.

Blodgett convection ovens represent the latest adĆ

vancement in energy efficiency, reliability, and

ease of operation. Heat normally lost, is recircuĆ

lated within the cooking chamber before being

vented from the oven: resulting in substantial reĆ

ductions in energy consumption and enhanced

oven performance.

GAS SPECIFICATIONS - U.S., Canada and General Export

Natural Gas Propane Gas

US Units SI Units US Units SI Units

Heating Value 1000 BTU/cu.ft. 37.3 MJ/m

2550 BTU/cu. ft. 95.0 MJ/m

Specific Gravity (air=1.0) 0.63 0.63 1.53 1.53

Gas Manifold Pressure 3.5" W.C. .87 kPa 10" W.C. 2.49 kPa

Oven Input 27,500 BTU/hr

34,500 BTU/hr

8.1 kW

10.1 kW

27,500 BTU/hr

34,500 BTU/hr

8.1 kW

10.1 kW

Main Burner Orifice Size 38 MTD*

32 MTD*

2.6 mm

2.9 mm

1/16" dia.

50 MTD*

1.6 mm

1.75 mm

Pilot Burner Orifice Size .021" dia. .55 mm .011" dia. .28 mm

GAS SPECIFICATIONS - Australia

Oven Input - 32 MJ - 32 MJ

Main Burner Orifice Size 38 MTD* 2.6 mm 1/16" dia. 1.6 mm

Gas Manifold Pressure - .87 kPa - 2.49 kPa

NOTE: *Multiple Twist Drill

Introduction

Oven Components

Combustion Cover - provides access to the

combustion compartment on gas ovens.

Combustion Compartment - contains combusĆ

tion burner on gas ovens.

Combustion Burner - provides heat to the bakĆ

ing chamber on gas ovens.

Control Panel - contains wiring and components

to control the oven operation.

Oven Racks - five racks are provided standard.

Additional racks are available.

Rack Supports - hold oven racks.

Blower Wheel Cover - located on the side interiĆ

or wall of the oven. Protects the blower wheel.

Blower Wheel - spins to circulate hot air in the

baking chamber.

Convection Motor - provides power to turn the

blower wheel.

Rack Support

Oven Rack

Figure 1

Installation

Delivery and Location

DELIVERY AND INSPECTION

All Blodgett ovens are shipped in containers to

prevent damage. Upon delivery of your new oven:

D Inspect the shipping container for external damĆ

age. Any evidence of damage should be noted

on the delivery receipt which must be signed by

the driver.

D Uncrate the oven and check for internal damĆ

age. Carriers will accept claims for concealed

damage if notified within fifteen days of delivery

and the shipping container is retained for inĆ

spection.

The Blodgett Oven Company cannot assume

responsibility for loss or damage suffered in

transit. The carrier assumed full responsibility

for delivery in good order when the shipment

was accepted. We are, however, prepared to

assist you if filing a claim is necessary.

OVEN LOCATION

The well planned and proper placement of your

oven will result in long term operator convenience

and satisfactory performance.

The following clearances must be maintained beĆ

tween the oven and any combustible or nonĆcomĆ

bustible construction.

D Oven body right side - 6" (15 cm)

D Oven body left side - 6" (15 cm)

D Oven body back - 6" (15 cm)

D Oven body bottom - 6" (15 cm)

The following clearances must be available for serĆ

vicing.

D Oven body sides - 12" (30 cm)

D Oven body back - 12" (30 cm)

NOTE: On gas models, routine servicing can usuĆ

ally be accomplished within the limited

movement provided by the gas hose reĆ

straint. If the oven needs to be moved furĆ

ther from the wall, the gas must first be

turned off and disconnected from the oven

before removing the restraint. Reconnect

the restraint after the oven has been reĆ

turned to its normal position.

It is essential that an adequate air supply to the

oven be maintained to provide a sufficient flow of

combustion and ventilation air.

D Place the oven in an area that is free of drafts.

D Keep the oven area free and clear of all combusĆ

tibles such as paper, cardboard, and flammable

liquids and solvents.

D Do not place the oven on a curb base or seal to

a wall. This will restrict the flow of air and prevent

proper ventilation. Tripping of the blower moĆ

tor's thermal overload device is caused by an

excessive ambient temperature on the right

side of the oven. This condition must be corĆ

rected to prevent permanent damage to the

oven.

D The location must provide adequate clearance

for the air opening into the combustion chamĆ

ber.

Before making any utility connections to this oven,

check the rating plate to be sure the oven specifiĆ

cations are compatible with the gas and electrical

services supplied for the oven.

1. Remove the combustion compartment cover.

The rating plate is attached to the frame in the

combustion compartment.

Installation

Stand Assembly

STAND OPTIONS

Small Stands Without Shelves

D The 5Ć3/4" (15cm) stand is used for a single

oven, when short legs are required for counterĆ

top use.

D The 7" (18cm) stand is used for a double

stacked oven, when the oven is to be located on

the floor.

Stands With Shelves

D Three stands, 16" (40cm), 19" (48cm), and 24"

(61cm) are available for different installation reĆ

quirements.

D The 33" (84cm) stand is used for a single oven

when counter space is limited.

Open Stands With Racks

D The 24" (61cm) or 33" (84cm) open stands are

available with a rack support system located beĆ

low the oven.

STAND ASSEMBLY

Small Stands Without Shelves

1. Place stand frame upside down on a work surĆ

face.

2. Attach one leg to each of the corner stud bolts

on the bottom of the stand top.

3. Place a lock washer and nut on each stud, and

tighten securely.

4. The stand is now ready for the oven assembly.

Stands With Shelves

1. Place stand frame upside down on a work surĆ

face.

2. Attach one leg to each of the corner stud bolts

on the bottom of the stand top.

3. Place a lock washer and nut on each bolt, and

tighten. DO NOT tighten leg bolts completely.

4. Place the shelf between the legs so that the

smooth top surface is facing the top of the

stand.

5. Align the shelf holes with the bolt holes found

near the bottom of each leg.

6. Insert a carriage bolt from the outside of the

leg, through the leg, and through the shelf corĆ

ner bracket.

7. Place a lock washer and nut on each bolt, and

tighten securely.

8. Tighten the leg frame bolts.

Figure 2

Installation

Stand Assembly

Open Stands With Racks

1. Lay stand frame top down on the floor as

shown. See Figure 3.

2. Position the four leg assemblies and support

angles as shown. Attach with the 5/16Ć18 nuts

provided. DO NOT tighten leg bolts completely.

NOTE: Be sure the support angles and clips

are located correctly for your oven

configuration. See Figure 3.

3. Position the bottom shelf between the legs so

that the smooth top surface is facing the top

of the stand.

4. Align the shelf holes with the bolt holes found

near the bottom of each leg.

5. Insert a carriage bolt from the outside of the

leg, through the leg, and through the shelf corĆ

ner bracket.

6. Place a lock washer and nut on each bolt, and

tighten securely. See the Figure 2.

7. Repeat Steps 3-6 for the top shelf.

NOTE: Be sure the slots in the top shelf are

aligned with the support angles.

8. Insert the top of the rack stops into the two

back clips on the angle supports as shown. InĆ

sert the bottom of the rack stops into the slots

in the top shelf as shown.

9. Insert the rack supports into the remaining

four clips on the angle supports as shown. InĆ

sert the bottom of the rack supports into the

slots in the top shelf as shown.

10. Tighten all loose bolts.

Support

Angle

Top Shelf

(rear)

Rack

Support

Attach Rack Supports and Rack Stops

Support

Angle,

Rack

Support

Back of Stand

Rack Stop

Support

Angle, LH

Figure 3

Installation

Oven Assembly

OVEN ASSEMBLY TO STAND

Single Section

1. Place the assembled stand in the location

where the oven is going to be used.

2. Remove the side control compartment cover

and open the front control panel of a single

oven (or lower section).

3. With a tool, punch out the knockĆouts in the

oven bottom near each corner.

4. Set the oven on the stand. Center it to the frame.

5. Align the front, and rear bolt holes of the oven

with the bolt holes in the stand.

6. Insert a bolt and washer, from the top down

through each of the 2 holes.

7. Place a nut and washer on each of the 2 bolts,

and tighten securely.

8. Replace the oven's side control compartment,

and close the front control panel.

NOTE: For single section ovens only. For

double stacked ovens step 8 will be

completed once the ovens are stacked.

Figure 4

Double Section

1. Assemble the lower section to the stand as deĆ

scribed. DO NOT replace the side control

compartment or close the front control panel.

2. With a tool, punch out the knockĆouts in the

oven top of the lower oven.

3. Remove the side control compartment cover

and open the front control panel of the upper

oven.

4. With a tool, punch out the knockĆouts in the

bottom of the upper oven near each corner.

5. Set the upper oven on the lower oven.

6. Align the front, and rear bolt holes of the upper

oven with the bolt holes in the bottom oven.

7. Insert a bolt and washer, from the top down

through each of the 2 holes.

8. Place a nut and washer on each of the 2 bolts,

and tighten securely.

9. Replace the control compartment cover, and

close the front control panel on both of the

ovens.

Figure 5

Installation

Oven Assembly

LEG ATTACHMENT

4" (10 cm legs)

1. Lay the oven on its back.

2. Screw the legs into the holes in the oven corĆ

ners. Tighten the hex nut at the top of each leg.

3. Tip the oven up on the legs.

4. Turn the adjustable leg feet to level the oven.

Figure 6

OVEN LEVELING

After assembly, the oven should be leveled and

moved to the operating location.

1. The oven can be leveled by adjusting the feet

or casters located on the bottom of each leg.

Installation

Ventilation

On gas models the installation of a proper ventilaĆ

tion system cannot be over emphasized. This sysĆ

tem removes unwanted vapors and products of

combustion from the operating area.

This oven may be vented using either:

D A mechanically driven, canopy type, exhaust

hood, or

D A direct flue arrangement.

U.S. and Canadian installations

Refer to your local ventilation codes. In the abĆ

sence of local codes, refer to the National ventilaĆ

tion code titled, Standard for the Installation of

Equipment for the Removal of Smoke and Grease

Laden Vapors from Commercial Cooking EquipĆ

ment", NFPAĆ96ĆLatest Edition.

Australia and General Export installations

Installation must conform with Local and National

installation standards. Local installation codes

and/or requirements may vary. If you have any

questions regarding the proper installation and/or

operation of your Blodgett oven, please contact

your local distributor. If you do not have a local disĆ

tributor, please call the Blodgett Oven Company at

0011Ć802Ć860Ć3700.

WARNING:

Failure to properly vent the oven can be

hazardous to the health of the operator

and may result in operational problems,

unsatisfactory baking and possible damĆ

age to the equipment.

Damage sustained as a direct result of imĆ

proper ventilation will not be covered by

the manufacturer's warranty.

CANOPY TYPE EXHAUST HOOD

A mechanically driven, canopy type exhaust hood

is the preferred method of ventilation.

The hood should be sized to completely cover the

equipment plus an overhang of at least 6" (15 cm)

on all sides not adjacent to a wall. The distance

from the floor to the lower edge of the hood should

not exceed 7' (2.1m).

The total makeup and exhaust air requirements for

hood capacity should be approximately 19 CFM

for each oven section.

Installing the canopy hood draft diverter

Ovens ordered for hood venting are supplied with

a draft diverter. Install the draft diverter as follows:

1. Place the diverter over the flue connector with

the open area facing the right side of the oven.

See Figure 7.

2. Secure with the sheet metal screws provided.

Front of

Oven

Draft Diverter

Figure 7

Installation

Ventilation

DIRECT FLUE ARRANGEMENT

When the installation of a mechanically driven exĆ

haust hood is impractical the oven may be vented

by a direct flue arrangement.

WARNING!!

It is essential that the direct flue be

installed as follows. Incorrect installation

will result in unsatisfactory baking and

oven damage.

The flue must be class B or better with a diameter

of 6" (15 cm). The height of the flue should rise 6Ć8

ft (2Ć2.5 m) above the roof of the building or any

proximate structure. Never direct vent the oven

into a hood. The flue should be capped with a UL

Listed type vent cap to isolate the unit from exterĆ

nal environmental conditions.

The direct vent cannot replace air consumed and

vented by the oven. Provisions must be made to

supply the room with sufficient makeĆup air. Total

makeĆup air requirements for each oven section

should be approximately 19 CFM per section. To

increase the supply air entering the room, a venĆ

tilation expert should be consulted.

Installing the draft hood

Ovens ordered for direct venting are supplied with

a draft hood. Install the draft hood as follows:

1. Place the draft hood over the flue connector.

See Figure 8.

2. Secure both ends with the sheet metal screws

provided.

Front of

Oven

Draft Hood

Flue

Figure 8

Installation

Utility Connections - Standards and Codes

THE INSTALLATION INSTRUCTIONS CONĆ

TAINED HEREIN ARE FOR THE USE OF QUALIĆ

FIED INSTALLATION AND SERVICE PERSONNEL

ONLY. INSTALLATION OR SERVICE BY OTHER

THAN QUALIFIED PERSONNEL MAY RESULT IN

DAMAGE TO THE OVEN AND/OR INJURY TO

THE OPERATOR.

Qualified installation personnel are individuals, a

firm, a corporation, or a company which either in

person or through a representative are engaged

in, and responsible for:

D the installation or replacement of gas piping

and the connection, installation, repair or servĆ

icing of equipment.

D the installation of electrical wiring from the elecĆ

tric meter, main control box or service outlet to

the electric appliance.

Qualified installation personnel must be experiĆ

enced in such work, familiar with all precautions

required, and have complied with all requirements

of state or local authorities having jurisdiction.

U.S. and Canadian installations

Installation must conform with local codes, or in

the absence of local codes, with the National Fuel

Gas Code, NFPA54/ANSI Z223.1-Latest Edition,

the Natural Gas Installation Code CAN/CGAĆ

B149.1 or the Propane Installation Code, CAN/

CGAĆB149.2 as applicable.

Installation must conform with local codes, or in

the absence of local codes, with the National ElecĆ

trical Code, ANSI/NFPA 70-Latest Edition and/or

Canadian National Electric Code C22.2 as appliĆ

cable.

Australia and General Export installations

Installation must conform with Local and National

installation standards. Local installation codes

and/or requirements may vary. If you have any

questions regarding the proper installation and/or

operation of your Blodgett oven, please contact

your local distributor. If you do not have a local disĆ

tributor, please call the Blodgett Oven Company at

0011Ć802Ć860Ć3700.

Installation

Gas Connection

GAS PIPING

A properly sized gas supply system is essential for

maximum oven performance. Piping should be

sized to provide a supply of gas sufficient to meet

the maximum demand of all appliances on the line

without loss of pressure at the equipment.

Example:

NOTE: BTU values in the following example are

for natural gas.

You purchase a DFGĆ50 convection oven to add to

your existing cook line.

1. Add the BTU rating of your current appliances.

Pitco Fryer 120,000 BTU

6 Burner Range 60,000 BTU

Deck Oven 50,000 BTU

Total 230,000 BTU

2. Add the BTU rating of the new oven to the toĆ

tal.

Previous Total 230,000 BTU

DFGĆ50 27,500 BTU

New Total 257,500 BTU

3. Measure the distance from the gas meter to

the cook line. This is the pipe length. Let's say

the pipe length is 40' (12.2 m) and the pipe

size is 1" (2.54 cm).

4. Use the appropriate table to determine the toĆ

tal capacity of your current gas piping.

The total capacity for this example is 320,000

BTU. Since the total required gas pressure,

257,500 BTU is less than 320,000 BTU, the

current gas piping will not have to be inĆ

creased.

NOTE: The BTU capacities given in the tables are

for straight pipe lengths only. Any elbows

or other fittings will decrease pipe capaciĆ

ties. Contact your local gas supplier if you

have any questions.

Maximum Capacity of Iron Pipe in Cubic Feet

of Natural Gas Per Hour

(Pressure drop of 0.5 Inch W.C.)

Pipe

L th (ft)

Nominal Size, Inches

Length (ft)

3/4" 1" 1Ć1/4" 1Ć1/4" 2"

10 360 680 1400 2100 3950

20 250 465 950 1460 2750

30 200 375 770 1180 2200

40 170 320 660 990 1900

50 151 285 580 900 1680

60 138 260 530 810 1520

70 125 240 490 750 1400

80 118 220 460 690 1300

90 110 205 430 650 1220

100 103 195 400 620 1150

From the National Fuel Gas Code Part 10 Table 10Ć2

Maximum Capacity of Pipe in Thousands of

BTU/hr of Undiluted L.P. Gas at 11" W.C.

(Pressure drop of 0.5 Inch W.C.)

Pipe Length

(ft)

Outside Diameter, Inches

(ft)

3/4" 1" 1Ć1/2"

10 608 1146 3525

20 418 788 2423

30 336 632 1946

40 287 541 1665

50 255 480 1476

60 231 435 1337

70 215 404 1241

80 198 372 1144

90 187 351 1079

100 175 330 1014

From the National Fuel Gas Code Part 10 Table 10Ć15

Installation

Gas Connection

PRESSURE REGULATION AND TESTING

DFGĆ50 ovens are rated at 27,500 BTU/Hr. (8.1

kW) (29 MJ) or 34,500 BTU/Hr. (10.1 kW) (36 MJ)

per section. Each oven has been adjusted at the

factory to operate with the type of gas specified on

the rating plate.

Inlet Pressure

Natural Propane

Min Max Min Max

W.C. 7.0 10.5 11.0 13.0

kPa 1.43 2.61 2.74 3.23

Manifold Pressure

Natural Propane

W.C. 3.5 10.0

kPa .87 2.49

D Inlet Pressure - the pressure of the gas before

it reaches the oven.

D Manifold Pressure - the pressure of the gas

as it enters the main burner(s).

D Min - the minimum pressure recommended to

operate the oven.

D Max - the maximum pressure at which the

manufacturer warrants the oven's operation.

Each oven is supplied with a regulator to maintain

the proper gas pressure. The regulator is essenĆ

tial to the proper operation of the oven and

should not be removed. It is preset to provide the

oven with 3.5" W.C. (0.87 kPa) for natural gas and

10.5" W.C. (2.50 kPa) for Propane at the manifold.

DO NOT INSTALL AN ADDITIONAL REGULATOR

WHERE THE OVEN CONNECTS TO THE GAS

SUPPLY UNLESS THE INLET PRESSURE IS

ABOVE MAXIMUM.

Prior to connecting the oven, gas lines should be

thoroughly purged of all metal filings, shavings,

pipe dope, and other debris. After connection, the

oven should be checked for correct gas pressure.

The oven and its individual shutoff valve must be

disconnected from the gas supply piping system

during any pressure testing of that system at test

pressures in excess of 1/2 psig (3.45kPa).

The oven must be isolated from the gas supply

piping system by closing its individual manual

shutoff valve during any pressure testing of the

gas piping system at test pressures equal or less

than 1/2 psig (3.45kPa).

Gas Connection 4" (101.6 mm)

Gas Connection 2.75" (69.9 mm)

Figure 9

Installation

Gas Connection

GAS HOSE RESTRAINT

If the oven is mounted on casters, a commercial

flexible connector with a minimum of 3/4" (1.9 cm)

inside diameter must be used along with a quick

connect device.

The restraint, supplied with the oven, must be

used to limit the movement of the unit so that no

strain is placed upon the flexible connector. With

the restraint fully stretched the connector should

be easy to install and quick connect.

The restraint (ie: heavy gauge cable) should be

1,000 lb. (453 kg) test load and should be attached

without damaging the building. DO NOT use the

gas piping or electrical conduit for the attachment

of the permanent end of the restraint! Use anchor

bolts in concrete or cement block. On wooden

walls, drive hi test wood lag screws into the studs

of the wall.

1. A 3/8" diameter hole has been provided on the

bottom of the oven just below the gas inlet. the

hole is sized to accept a clipĆon restraining

cable supplied with the flex hose.

WARNING!!

If the restraint is disconnected for any

reason it must be reconnected when the

oven is returned to its original position.

U.S. and Canadian installations

The connector must comply with the Standard for

Connectors for Movable Gas Appliances, ANSI

Z21.69 or Connectors For Moveable Gas ApĆ

pliances CAN/CGAĆ6.16ĆM87 and a quick disconĆ

nect device that complies with the Standard for

QuickĆDisconnect Devices for Use With Gas Fuel,

ANSI Z21.41 or Quick Disconnect For Use With

Gas Fuel CAN 1Ć6.9. Adequate means must be

provided to limit the movement of the appliance

without depending on the connection and the

quick disconnect device or its associated piping.

Australia and General Export installations

The restraint and quick connect must conform

with Local and National installation standards. LoĆ

cal installation codes and/or requirements may

vary. If you have any questions regarding the propĆ

er installation and/or operation of your Blodgett

oven, please contact your local distributor. If you

do not have a local distributor, please call the

Blodgett Oven Company at 0011Ć802Ć860Ć3700.

Installation

Electrical Connection

Wiring diagrams are located in the motor access

panel and on the back of the oven.

This oven is supplied for connection to 115 volt

grounded circuits. The electric motor, indicator

lights and related switches are connected through

the 6' electric supply cord found at the rear of the

oven.

THE BLODGETT OVEN COMPANY CANNOT ASĆ

SUME RESPONSIBILITY FOR LOSS OR DAMAGE

SUFFERED AS A RESULT OF IMPROPER INSTALĆ

LATION.

WARNING!!

This appliance is equipped with three

prong grounding type plug for your

protection against shock hazard and

should be plugged directly into a properly

grounded three prong receptacle. DO

NOT cut or remove the grounding prong

from this plug.

ELECTRICAL SPECIFICATIONS

Model Hz Volts Phase Amps Electrical Connection

(minimum size)

U.S. and Canadian Installations

DFGĆ50 60 115 1 5 Cord set provided

General Export Installations

DFGĆ50 50 220Ć240 1 3 Size per local code

Installation

Initial Startup

The following is a checkĆlist to be completed by

qualified personnel prior to turning on the

appliance for the first time.

j Open the manual shutĆoff valve at the rear of

the oven.

j Remove the control panel and combustion

covers.

j Turn the combination valve's manual shutĆoff

to the on position.

j Turn the selector switch to Cook, and the therĆ

mostat to 500_F (260_C).

With the main burner on, check the following.

j Verify there are no gas leaks, by checking all

gas connections with a soapy water solution.

j Verify that the inlet pressure is correct. The inĆ

let pressure can be checked at the pressure

tap located on the combination valve's inlet

side.

j Verify that the manifold pressure is correct.

The manifold pressure can be checked at the

pressure tap located on the combination

valve's outlet side.

j If the above pressure readings are set to the

recommended pressure requirements, allow

the oven to burnĆoff for 2 hours. If the pressure

readings are not set correctly, turn off the oven

and readjust accordingly.

WARNING

The break in procedure burns off excess

oils present in the metals during fabricaĆ

tion. Smoke may be produced. Proper

ventilation is required.

ADJUSTMENTS ASSOCIATED WITH INITIAL

INSTALLATION

Each oven, and its component parts, have been

thoroughly tested and inspected prior to shipĆ

ment. However, it is often necessary to further

test or adjust the oven as part of a normal and

proper installation. These adjustments are the

responsibility of the installer, or dealer. Since

these adjustments are not considered defects

in material or workmanship, they are not covĆ

ered by the Original Equipment Warranty. They

include, but are not limited to:

D calibration of the thermostat

D adjustment of the doors

D burner adjustments

D leveling

D testing of gas pressure

D tightening of fasteners.

No installation should be considered complete

without proper inspection, and if necessary,

adjustment by qualified installation or service

personnel.

La page charge ...

Blodgett DFG-50 Mode d'emploi

Marque: Blodgett

Modèle: DFG-50

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Blodgett DFG-50 Operating instructions

Documents connexes

Autres documents

Silvercrest SHLF 2000 B1 Operating Instructions Manual