Maytag FG7S(C,L) Guide d'installation

Marque: Maytag

Modèle: FG7S(C,L)

Taper: Guide d'installation

Ce manuel convient également à

*SL (92.1% AFUE) &

*SM (95.0% AFUE)

Downﬂow Furnace

92.1% Through 95.0% AFUESingle Stage Condensing Gas Furnaces

*SD & *SD-E (95.0% AFUE)

Upﬂow / Horizontal Furnace

*SC (92.1%AFUE)

Upﬂow / Horizontal Furnace

INSTALLATION INSTRUCTIONS

WARNING

FIRE OR EXPLOSION HAZARD





supplier.





WHAT TO DO IF YOU SMELL GAS











DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION ..........................3

REQUIREMENTS & CODES ..........................................4

Combustion Air Quality ................................................5

Heating Load ................................................................5

Installation in a Garage ................................................6

Clearances to Combustible Materials ..........................6

Operation of Furnace During Construction ..................6

COMBUSTION AIR & VENTING REQUIREMENTS .......7

Direct Vent Furnaces ....................................................8

Conventional Vent Systems - Conﬁned Spaces ..........8

Air From Inside .........................................................8

Outdoor Air from a Crawl Space or Vented Attic .......8

Outdoor Air Using Vertical Ducts ..............................8

Outdoor Air Using Horizontal Ducts ..........................9

Air Directly Through An Exterior Wall ........................9

Alternate Method of Providing Air from Outside .......10

Conventional Vent Systems - Unconﬁned Spaces ......10

Category IV Venting .....................................................10

Vent Pipe Material .....................................................11

Vent Pipe Length & Diameter ...................................11

Vent Pipe Installation ................................................11

Outdoor Terminations - Horizontal Venting ...............12

Outdoor Terminations - Vertical Venting ....................13

Vent Freezing Protection ...........................................13

Existing Installations .................................................13

Condensate Disposal ...................................................13

CIRCULATING AIR REQUIREMENTS ...........................14

Plenums & Air Ducts ....................................................14

Return Air Connections ................................................14

Upﬂow & Horizontal Furnaces ..................................14

Downﬂow Furnaces ..................................................15

Supply Air Connections ................................................15

Acoustical Treatments ..................................................15

FURNACE INSTALLATION ............................................15

General Requirements .................................................15

Upﬂow Furnaces ..........................................................15

Horizontal Furnaces .....................................................15

Special Instructions for SC038-23A Furnaces ..........16

Downﬂow Furnaces ......................................................16

Installation on a Concrete Slab .................................17

Inducer & Venting Options ...........................................17

Inducer Assembly Rotation .......................................18

Pressure Switch Tubing ............................................18

Alternate Pressure Switch Location ..........................18

Accessories ..................................................................19

Finish Flange ............................................................19

Rubber Grommets ....................................................19

PVC Components .....................................................20

Typical Orientation ................................................20

Alternate Orientation ............................................20

Optional PVC Pipe Installation ..................................20

Condensate Drain Lines ...........................................20

Bottom Panel Removal.................................................21

Alternate Bottom Panel Removal .................................21

GAS SUPPLY & PIPING .................................................22

Leak Check ..................................................................22

High Altitude Application (Natural Gas Only) ...............22

Converting from Natural Gas to LP / Propane .............23

ELECTRICAL WIRING ....................................................26

Line Voltage Wiring ......................................................26

Grounding .....................................................................26

Thermostat / Low Voltage Connections .......................26

Heat Anticipator ............................................................26

Twinning .......................................................................27

START-UP & ADJUSTMENTS ........................................28

Pre-Start Check List .....................................................28

Start-up Procedures .....................................................28

Verifying & Adjusting Input Rate ..................................29

Verifying & Adjusting Temperature Rise ......................29

Verifying Burner Operation ...........................................29

Verifying Operation of the Supply Air Limit Switch ......29

Conﬁguring The Blower ................................................30

Selecting the (Gas) Heating Speed ..........................30

Determining Nominal System Capacity ....................30

Selecting the Cooling/Heat Pump Speed .................30

System Operation ........................................................30

(Gas) Heating Mode .................................................30

Cooling or Heat Pump Mode ....................................30

Manual Fan ...............................................................30

Fault Conditions ...........................................................30

OPERATING SEQUENCE ..............................................30

Heating Cycle ...............................................................30

Cooling Cycle ...............................................................31

Fan Mode .....................................................................31

MAINTENANCE ..............................................................31

IMPORTANT SAFETY INFORMATION

INSTALLER: Please read all instructions before servicing

this equipment. Pay attention to all safety warnings and

any other special notes highlighted in the manual. Safety

markings are used frequently throughout this manual to

designate a degree or level of seriousness and should not

be ignored. WARNING - Indicates a potentially hazardous

situation that if not avoided, could result in personal injury

or death.

CAUTION - Indicates a potentially hazardous

situation that if not avoided, may result in minor or moderate

injury or property damage.

WARNING:





     





    

     



WARNING:

    





WARNING:

    





      

     





WARNING:





      









• Tominimizeequipmentfailureorpersonalinjury,itis

essential that only qualiﬁed individuals install, service,

or maintain this equipment. If you do not posses

mechanical skills or tools, call your local dealer for

assistance.

FIGURES & TABLES ......................................................32

Figure 31. *SL & *SM Cabinet Dimensions ...............32

Figure 32. *SC, *SD & *SD-E Cabinet Dimensions ..33

Airﬂow Data ..................................................................34

Table 6. *SC Upﬂow / Horizontal Furnaces ...............34

Table 7. *SL Downﬂow Furnaces ..............................35

Table 8. *SD & *SD-E Upﬂow / Horizontal

Furnaces (ECM Motor) ...............................36

Table 9. *SD & *SD-E Upﬂow / Horizontal

Furnaces .....................................................38

Table 10. *SM Downﬂow Furnaces ...........................39

Electrical Information....................................................40

Figure 33. Wiring Diagram ........................................40

Figure 34. Wiring Diagram (Fixed Speed) .................41

Gas Information ............................................................42

Table 11. Gas Flow Rates .........................................42

Table 12. Gas Pipe Capacities ..................................42

Table 13. High Altitude Deration – Propane Gas ......43

Table 14. Natural Gas Heating Values ......................43

Table 15. High Altitude Deration – Natural Gas with

HIGH Heating Value ..................................44

Table 16. High Altitude Deration – Natural Gas with

LOW Heating Value ...................................44

Venting Information ......................................................45

Table 17. Vent Termination Clearances .....................45

*SC & *SL Series

Figure 35. Horizontal & Vertical Venting ....................46

Figure 36. Venting Options for Upﬂow Installations

(*SC Series) .............................................47

Figure 37. Venting Options for 1 Pipe Horizontal

Installations (*SC Series) .........................48

Figure 38. Venting Options for 2-Pipe Horizontal

Installations (*SC Series) .........................49

Figure 39. Venting Options for Downﬂow

Installations (*SL Series) ..........................50

*SD, *SD-E & *SM Series

Figure 40. Horizontal & Vertical Venting ....................51

Figure 41. Venting Options for Upﬂow Installations

(*SD & *SD-E Series) ...............................52

Figure 42. Venting Options for Horizontal Installations

(*SD & *SD-E Series) ..............................53

Figure 43. Venting Options for Downﬂow Installations

(*SM Series) .............................................54

TROUBLESHOOTING ....................................................55

Table 18. Control Board Fault Conditions .................55

Table 19. Motor Control Board Fault Conditions .......55

FURNACE COMPONENTS ............................................55

Figure 44. *SC & *SD & *SD-E Component

Locations ..................................................56

Figure 45. *SL & *SM Component Locations ............57

INSTALLATION / PERFORMANCE CHECK LIST .........62

• Followall precautions in the literature, on tags, and

on labels provided with the equipment. Read and

thoroughly understand the instructions provided with

the equipment prior to performing the installation and

operational checkout of the equipment.

• Usecautionwhenhandlingthisapplianceorremoving

components. Personal injury can occur from sharp

metal edges present in all sheet metal constructed

equipment.

• Donotstoreanyofthefollowingon,orincontactwith,

the unit: Rags, brooms, vacuum cleaners, or other

cleaning tools, spray or aerosol cans, soap powders,

bleaches, waxes, cleaning compounds, plastics or

plastic containers, paper bags or other paper products,

gasoline, kerosene, cigarette lighter ﬂuid, dry cleaning

ﬂuids, paint thinners, or other volatile ﬂuids.

• The installer should become familiar with the

units wiring diagram before making any electrical

connections to the unit. See Figure 33 (page 40),

Figure 34 (page 41), or the unit wiring label.

        





REQUIREMENTS & CODES

WARNING:



     

      

    

     



• This furnace must be installed in accordance with

these instructions, all applicable local building codes

and the current revision of the National Fuel Gas

Code (NFPA54/ANSI Z223.1) or the Natural Gas and

Propane Installation Code, CAN/CGA B149.1.

• Use onlywithtype ofgas approvedforthis furnace.

Refer to the furnace rating plate.

• Installthisfurnaceonlyinalocationandpositionas

speciﬁed on page 6.

• Provideadequatecombustionandventilationairtothe

furnace space as speciﬁed on page 7, page 8,

page 9

& page 10.

• Provide adequate clearances around the vent air

intake terminal as shown in Figure 7 (page 12), Figure

8 (page 12)

, Figure 9 (page 12), & Figure 10 (page

12)

• Combustion products must be discharged outdoors.

Connect this furnace to an approved vent system only,

as speciﬁed on page 10, page 11, page 12, & page

• Never test for gas leaks withan open ame. Use a

commercially available soap solution to check all

connections. See page 22.

• Thisfurnaceisdesignedtooperatewithamaximum

external pressure rise of 0.5 inches of water column.

Consult Table 6 (page 34), Table 7 (page 35), Table

8 (page 36)

, Table 9 (page 38), & Table 10 (page

39)

and the rating plate for the proper circulating air

ﬂow and temperature rise. It is important that the duct

system be designed to provide the correct ﬂow rates

and external pressure rise. An improperly designed

duct system can result in nuisance shutdowns, and

comfort or noise issues.

• Whensupplyductscarryaircirculatedbythefurnace

to areas outside the space containing the furnace, the

return air shall also be handled by duct(s) sealed to

the furnace casing and terminating in the conditioned

space. See page 14 .

• A gas-red furnace for installation in a residential

garage must be installed as speciﬁed on page 6.

• This furnace may be used for temporary heating of

buildings or structures under construction. See the

guidelines listed on page 6.

• Thisfurnaceisnotapprovedforinstallationinmobile

homes. Installing this furnace in a mobile home could

cause ﬁre, property damage, and/or personal injury.

• The Commonwealth of Massachusetts requires

compliance with regulation 248 CMR 4.00 and 5.00

for installation of through – the – wall vented gas

appliances as follows:

1. For direct-vent appliances, mechanical-vent heating

appliances or domestic hot water equipment, where the

bottom of the vent terminal and the air intake is installed

below four feet above grade the following requirements

must be satisﬁed:

a.) A carbon monoxide (CO) detector and alarm shall

be placed on each ﬂoor level where there are

bedrooms. The detector shall comply with NFPA

720 (2005 Edition) and be mounted in the living

area outside the bedroom(s).

b.) A (CO) detector shall be located in the room that

houses the appliance or equipment and shall:

•Bepoweredbythesameelectricalcircuitasthe

appliance or equipment. Only one service switch

shall power the appliance and the (CO) detector;

•Havebatteryback-uppower;

•MeetANSI/UL2034Standardsandcomplywith

NFPA 720 (2005 Edition); and Approved and listed

by a Nationally Recognized Testing Laboratory as

recognized under 527 CMR.

c.) A Product-approved vent terminal must be used,

and if applicable, a product-approved air intake must

be used. Installation shall be in strict compliance

with the manufacturer’s instructions. A copy of

the installation instructions shall remain with the

appliance or equipment at the completion of the

installation.

d.) A metal or plastic identiﬁcation plate shall be

mounted at the exterior of the building, four feet

directly above the location of vent terminal. The

plate shall be of sufﬁcient size, easily read from

a distance of eight feet away, and read “Gas Vent

Directly Below”.

2. For direct-vent appliances, mechanical-vent heating

appliances or domestic hot water equipment where the

bottom of the vent terminal and the air intake is installed

above four feet above grade the following requirements

must be satisﬁed:

a.) A (CO) detector and alarm shall be placed on each

ﬂoor level where there are bedrooms. The detector

shall comply with NFPA 720 (2005 Edition) and be

mounted in the living area outside the bedroom(s).

b.) The (CO) detector shall:

•Belocatedintheroomthathousestheappliance

or equipment;

•Behard-wiredorbatterypoweredorboth.

•ShallcomplywithNFPA720(2005Edition).

c.) A product-approved vent terminal must be used,

and if applicable, a product-approved air intake must

be used. Installation shall be in strict compliance

with the manufacturer’s instructions. A copy of

the installation instructions shall remain with the

appliance or equipment at the completion of the

installation.

The information listed below is for reference purposes only

and does not necessarily have jurisdiction over local or

state codes. Always consult with local authorities before

installing any gas appliance.



• US:NationalFuelGasCode(NFGC),AirforCombustionand

Ventilation

• CANADA: Natural Gas and Propane Installation Codes

(NSCNGPIC), Venting Systems and Air Supply for Appliances



• USandCANADA:AirConditioningContractorsAssociation

(ACCA) Manual D, Sheet Metal and Air Conditioning

Contractors National Association (SMACNA), or American

Society of Heating, Refrigeration, and Air Conditioning

Engineers (ASHRAE) Fundamentals Handbook

Electrical Connections

• US:NationalElectricalCode(NEC)ANSI/NFPA70

• CANADA:CanadianElectricalCodeCSAC22.1

Gas Piping & Gas Pipe Pressure Testing

• US:NFGCandNationalPlumbingCodes

• CANADA:NSCNGPIC

General Installation

• US: Current edition of theNFGC and the NFPA 90B. For

copies, contact the National Fire Protection Association Inc.,

Batterymarch Park, Quincy, MA 02269; or American Gas

Association, 400 N. Capitol, N.W., Washington DC 20001 or

www.NFPA.org

• CANADA:NSCNGPIC.Foracopy,contactStandardSales,

CSA International, 178 Rexdale Boulevard, Etobicoke

(Toronto), Ontario, M9W 1R3 Canada



• US:(NFGC)NFPA54–1999/ANSIZ223.1andtheInstallation

Standards, Warm Air Heating and Air Conditioning Systems

ANSI/NFPA 90B.

• CANADA:CAN/CGA-B149.1and.2–M00NationalStandard

of Canada. (NSCNGPIC)



CAUTION:

       



To maximize heat exchanger life, the combustion air

must be free of chemicals that can form corrosive acidic

compounds in the combustion gases. The recommended

source of combustion air is to use outdoor air. However,

the use of indoor air in most applications is acceptable

except as listed:

• Ifthefurnaceisinstalledasasinglepipeinstallation

in a conﬁned space, it is required that the necessary

combustion air come from the outdoors by way of attic,

crawl space, air duct, or direct opening. For Installations

in conﬁned spaces, see page 8 for combustion air

requirements.

• Installationsintheselocationsmayrequireoutdoorair

for combustion, due to chemical exposures:

Commercial buildings

Buildings with indoor pools

Furnaces installed in laundry rooms

Furnaces installed in hobby or craft rooms

Furnaces installed near chemical storage areas

• Exposuretothefollowingsubstancesinthecombustion

air supply may require outdoor air for combustion:

Permanent wave solutions

Chlorinated waxes and cleaners

Chlorine based swimming pool chemicals

Water softening chemicals

De-icing salts or chemicals

Carbon Tetrachloride

Halogen type refrigerants

Cleaning solvents (perchloroethylene)

Printing inks, paint removers, varnishes, etc.

Hydrochloric Acid

Cements and glues

Antistatic fabric softeners

Masonry acid washing materials

Heating Load

This furnace should be sized to provide the design heating

load requirement. Heating load estimates can be made

using approved methods available from Air Conditioning

Contractors of America (Manual J); American Society of

Heating, Refrigerating, and Air Conditioning Engineers;

or other approved engineering methods. 

   



The ductwork should be appropriately sized to the capacity

of the furnace to ensure its proper airﬂow rating. For

installations above 2,000 ft., the furnace should have a

sea level input rating large enough that it will meet the

heating load after deration for altitude.

Installation in a Garage

WARNING:



        







This gas-ﬁred furnace may be installed in a residential

garage with the provision that the burners and igniter

are located no less than 18 inches (457mm) above the

ﬂoor. The furnace must be located or protected to prevent

physical damage by vehicles.



This furnace is Design Certiﬁed in the U.S. and Canada

by CSA International for the minimum clearances to

combustible materials. NOTE: The furnace is listed for

installation on combustible or non-combustible ﬂooring.

However, wood is the only combustible ﬂooring allowed

for installation. Downﬂow models must use the appropriate

subase kit when installing over a wood ﬂoor. To obtain

model number and speciﬁc clearance information, refer

to the furnace rating plate, located inside of the furnace

cabinet.

Access for positioning and servicing the unit must be

considered when locating unit. The need to provide

clearance for access to panels or doors may require

clearance distances over and above the requirements.





See Figure 1 for minimum clearance requirements.



CAUTION:







        





Operating gas furnaces in construction environments can

cause a variety of problems with the furnace. Proper use

of commercial portable space heating equipment during

construction is recommended. This gas furnace may be

used during construction if it is not in violation of any

applicable codes and the following criteria are met:

• The installation mustmeetall applicablecodes.The

furnace must be permanently installed according to

the instructions supplied with the furnace including

electrical supply, gas supply, duct work and venting. The

furnace must be controlled by a thermostat properly

installed according to the instructions supplied with the

furnace and thermostat. The installation must include

a properly installed ﬁlter in the return air system with

no by-pass air. The ﬁlter must be inspected frequently

and replaced when necessary.

• Combustion air must be supplied from outside the

structure and located such that dust and gases

from construction activity are not introduced into the

combustion system.

• Provisions must be made to insure that condensate

does not freeze in the furnace or condensate drain

lines during operation and during idle times; for

example, overnight if turned off.

• Before occupying the structure: The lter must be

replaced or cleaned, the duct work must be inspected

and cleaned of any construction debris, and the

furnace must be cleaned and/or repaired if found to

be dirty, damaged, or malfunctioning in any way by

a qualiﬁed HVAC technician. The furnace shall be

inspected and approved by applicable local authority

even if this requires redundant inspections.

• Serialnumbersforfurnacesusedduringconstruction

must be submitted in writing (fax and email also

acceptable). This information will be used to track the

long-term affects of the use during construction on

furnaces. Proof of this submittal shall be available for

the ﬁnal inspection of the furnace prior to occupancy.

• This furnace is designed to operate with return air

temperatures in ranges normally found in occupied

residences, including setbacks. Minimum continuous

return temperature must not be below 60° F (15° C).

Occasionally a temporary return temperature of 55° F

(12° C) is acceptable. However, operation with a return

temperature below 55° F (12° C) is not allowed.

CLEARANCES TO COMBUSTIBLE MATERIALS

Left Side..................0 Inches Top ..........................0 Inches

Right Side ...............0 Inches Front ......................

†

4 Inches

Vent .........................0 Inches Back ........................0 Inches

†Allow 24 in. minimum clearance for servicing. Recommended clearance

is 36 in.

Figure 1. 



TOP

FRONT

UPFLOW

APPLICATIONS

HORIZONTAL

APPLICATIONS

VENT

TOP

FRONT

DOWNFLOW

APPLICATIONS

SIDE

TOP

BOTTOM

VENT

FRONT

BACK

SIDE

LEFT SIDE

RIGHT SIDE

COMBUSTION AIR & VENTING

REQUIREMENTS

WARNING:

CARBON MONOXIDE POISONING HAZARD

      



     



      



     

while all other appliances connected to the



      













      









in which the appliance(s) connected to the







      







      



6. Follow the lighting instructions. Place the

    





      

      









corrected in accordance with the National Fuel





Codes.

      

     





     



IMPORTANT INFORMATION:

 





        

     

       



      



 



with the National Fuel Gas Code (NFGC) and all



      









   





   





page 5.

WARNING:

     

      

    



 





WARNING:

       

       





      

   





This condensing furnace is certiﬁed for installation either as

a Direct Vent (2-pipe) or Conventional (1-pipe) appliance.

Direct Vent appliances draw combustion air from the

outdoors and vent combustion products back outside.

Installation with air taken from around the furnace is often

referred to as Conventional installation - i.e. only the vent

(exhaust) pipe is provided.

Another important consideration when selecting one or

two pipe installation is the quality of the Indoor air which

can sometimes be contaminated with various household

chemicals . These chemicals can cause severe corrosion

in the furnace combustion system. A 2-pipe installation

has the additional advantage that it isolates the system

from the effects of negative pressure in the house.

CAUTION:

     











      







Air openings on top of the furnace and openings in closet

doors or walls must never be restricted. If the furnace is

operated without adequate air for combustion, the ﬂame

roll-out switch will open, turning off the gas supply to the

burners.

IMPORTANT NOTE





 







Direct Vent Furnaces

Direct Vent (2-pipe) furnaces draw combustion air directly

from the outdoors and then vent the combustion products

back outside, isolating the entire system from the indoor

space. It is important to make sure that the whole system

is sealed and clearances to combustibles are maintained

regardless of the installation being in a conﬁned or

unconﬁned space.

    

Spaces

A conﬁned space is an area with volume less than 50

cubic feet per 1,000 Btuh of the combined input rates of

all appliances drawing combustion air from that space.

Furnace closets, small equipment rooms and garages are

conﬁned spaces. Furnaces installed in a conﬁned space

which supply heated air to areas outside the space must

draw return air from outside the space and must have the

return air ducts tightly sealed to the furnace. Ducts must

have cross - sectional area at least as large as the free area

of their respective openings to the furnace space. Attics

or crawl spaces must connect freely with the outdoors if

they are the source of air for combustion and ventilation.

The required sizing of these openings is determined by

whether inside or outside air is used to support combustion,

the method by which the air is brought to the space, and

by the total input rate of all appliances in the space. In

all cases, the minimum dimension of any combustion air

opening is 3 inches.

Air From Inside

If combustion air is taken from the heated space, the two

openings must each have a free area of at least one square

inch per 1,000 Btuh of total input of all appliances in the

conﬁned space, but not less than 100 square inches of

free area. See Example and Figure 2.

EXAMPLE

If the combined input rate of all appliances is less than

or equal to 100,000 Btuh, each opening must have

a free area of at least 100 in

. If the combined input

rate of all appliances is 120,000 Btuh, each opening

must have a free area of at least 120 in

TOTAL INPUT

RATING (BTUH)

MINIMUM FREE AREA

(EACH OPENING)

ROUND DUCT

DIAMETER

40,000 100 sq. In 12 inches

60,000 100 sq. In 12 inches

80,000 100 sq. In 12 inches

100,000 100 sq. In 12 inches

120,000 120 sq. In 13 inches

140,000 140 sq. In 14 inches

160,000 160 sq. In 15 inches

Figure 2. 

Vent or

Chimney

Furnace

Water

Heater

12” Max.

See

Notes

See

Notes

NOTES:

Each opening must be

at least 100 sq. in. or

1 sq. in. per 1,000 Btuh

of total input rating,

whichever is greater.

Openings must start at

no more than 12 inches

from the top and bottom

of the enclosure.

Outdoor Air from a Crawl Space or Vented

Attic

When the openings can freely exchange air with the

outdoors, each opening shall have a minimum free area

of 1 square inch per 4,000 Btuh of total appliance input.

The openings shall exchange directly, or by ducts, with

the outdoor spaces (crawl or attic) that freely exchange

with the outdoors. See Figure 3 (page 9).

Outdoor Air Using Vertical Ducts

If combustion air is taken from outdoors through vertical

ducts, the openings and ducts must have a minimum free

area of one square inch per 4,000 Btuh of total appliance

input. See Figure 4 (page 9).

Outdoor Air Using Horizontal Ducts

If combustion air is taken from outdoors through horizontal

ducts, the openings and ducts must have a minimum free

area of one square inch per 2,000 Btuh of total appliance

input. Ducts must have cross - sectional area at least as

large as the free area of their respective openings to the

furnace space. See Figure 5.

Air Directly Through An Exterior Wall

If combustion air is provided directly through an exterior

wall, the two openings must each have free area of at

least one square inch per 4,000 Btuh of total appliance

input. See Figure 6,

Figure 4. 

Through Vertical Ducts

TOTAL INPUT

RATING (BTUH)

MINIMUM FREE AREA

(EACH OPENING)

ROUND DUCT

DIAMETER

40,000 10 sq. In 4 inches

60,000 15 sq. In 5 inches

80,000 20 sq. In 5 inches

100,000 25 sq. In 6 inches

120,000 30 sq. In 6 inches

140,000 35 sq. In 7 inches

160,000 40 sq. In 8 inches

Air Duct must be

at least 1 sq. in.

per 4,000 Btuh of

total input rating.

Ducts must

extend above

attic insulation.

Air Duct must be

at least 1 sq. in.

per 4,000 Btuh of

total input rating.

Ventilation Louvers

at each end of attic

Attic

Insulation

12" Max

Furnace

Water

Heater

Vent or

Chimney

Water

Heater

Vent or

Chimney

Furnace

Ventilation Louvers For

Unheated Crawl Space

Inlet Air

Ventilation Louvers

(each end of attic)

NOTE: Air openings shall

each have a free area of

not less than one square

inch per 4,000 Btuh of the

total input rating of all

equipment in the enclosure

Alternate

Air Inlet

Outlet

Air

Figure 3. 

Space or Vented Attic

Figure 5. 

Through Horizontal Ducts

TOTAL INPUT

RATING (BTUH)

MINIMUM FREE AREA

(EACH OPENING)

ROUND DUCT

DIAMETER

40,000 20 sq. In 5 inches

60,000 30 sq. In 6 inches

80,000 40 sq. In 7 inches

100,000 50 sq. In 8 inches

120,000 60 sq. In 9 inches

140,000 70 sq. In 10 inches

160,000 80 sq. In 10 inches

Furnace

Water

Heater

Air Ducts must be

at least 1 sq. in.

per 2,000 Btuh of

total input rating.

Vent or

Chimney

Air Duct

TOTAL INPUT

RATING (BTUH)

MINIMUM FREE AREA

(EACH OPENING)

ROUND DUCT

DIAMETER

40,000 10 sq. In 4 inches

60,000 15 sq. In 5 inches

80,000 20 sq. In 5 inches

100,000 25 sq. In 6 inches

120,000 30 sq. In 6 inches

140,000 35 sq. In 7 inches

160,000 40 sq. In 8 inches

Figure 6. 



NOTE: Each opening to outside

must be at least 1 sq. in. per

4,000 Btuh of total input rating.

12" Max.

Furnace

Water

Heater

Vent or

Chimney

12"

Max

See

Note

See

Note

Alternate Method of Providing Air from

Outside

If acceptable under local Codes, it is permitted to provide

outside air using one opening (See NFGC). Generally,

conﬁned spaces must have two openings in the space for

combustion air. One opening must be within 12 inches of

the ceiling, and the other must be within 12 inches of the

ﬂoor. However, an alternative method recently adopted by

the NFGC uses one opening within 12 inches of the top

of the space. This method may be used if it is acceptable

to the local codes.

THE FOLLOWING CONDITIONS MUST BE MET:

1. The opening must start within 12” of the top of the

structure and connect with the out of doors through

vertical or horizontal ducts or be ducted to a crawl or

attic space that connects with the out of doors.

2. The opening must have a minimum free area of 1 sq.

in. per 3,000 Btu per hour of the total input rating of all

equipment located in the enclosure.

3. The free area must not be less than the sum of all the

areas of the vent connectors in the enclosure.

    

Spaces

An unconﬁned space is an area including all rooms not

separated by doors with a volume greater than 50 cubic

feet per 1,000 Btuh of the combined input rates of all

appliances which draw combustion air from that space.

In general, a furnace installed in an unconﬁned space will

not require outside air for combustion. However, in homes

built for energy efﬁciency (low air change rates), it may

be necessary to provide outside air to ensure adequate

combustion and venting, even though the furnace is located

in an unconﬁned space. See Example below.

EXAMPLE

A space with a water heater rated at 45,000 Btuh

input and a furnace rated at 75,000 Btuh requires a

volume of 6,000 cubic feet [50 x (45 + 75) = 6,000] to

be considered unconﬁned. If the space has an 8 foot

ceiling, the ﬂoor area of the space must be 750 sq. ft.

(6,000 / 8 = 750).



WARNING:

     

      

      









This furnace is classiﬁed as a “Category IV” appliance,

which requires special venting materials and installation

procedures. This section speciﬁes installation requirements

for Conventional (1-pipe) and Direct Vent (2-pipe) piping.

For 1- pipe installations, install vent piping as described in

this section and provide air for combustion and ventilation

according to page 7, page 8, page 9 & page 10.

The length of vent and combustion air piping for either

type of installation are llisted in Table 1.

FURNACE

MODELS

(BTU)

FURNACE

INSTALLATION

SINGLE VENT PIPE LENGTH (FT.)

WITH 1 LONG RADIUS ELBOW†

DUAL VENT PIPE LENGTH (FT.)

WITH 1 LONG RADIUS ELBOW ON EACH PIPE†

OUTLET

2” DIAMETER

OUTLET

3” DIAMETER

INLET / OUTLET

2” DIAMETER

INLET / OUTLET

3” DIAMETER

38,000 Upﬂow 50 70 50 70

54,000

Upﬂow 70 90 70 90

Downﬂow 70 90 70 90

72,000

Upﬂow 50 90 50 90

Downﬂow 50 90 50 90

90,000

Upﬂow 60 90 60 90

Downﬂow 60 90 60 90

108,000 Upﬂow N/A 90 N/A 90

118,000 Downﬂow N/A 90 N/A 90

120,000

Upﬂow N/A 90 N/A 90

Downﬂow N/A 90 N/A 90

†

NOTES:

1. Subtract 2.5 ft. for each additional 2 inch long radius elbow, 5 ft. for each additional 2 inch short radius elbow, 3.5 ft. for each additional 3 inch long radius elbow,

and 7 ft. for each additional 3 inch short radius elbow. Subtract 5 ft for each 2” tee and 8 ft for each 3” tee.

2. Two 45 degree elbows are equivalent to one 90 degree elbow.

3. This table applies for elevations from sea level to 2,000 ft. For higher elevations, decrease pipe lengths by 8% per 1,000 ft of altitude.

4. A long radius elbow’s centerline radius is equal to or greater than 1.5 times the vent diameter.

Vent Pipe Lengths

Category IV appliances operate with positive vent pressure

and therefore require vent systems which are thoroughly

sealed. They also produce liquid condensate, which is

slightly acidic and can cause severe corrosion of ordinary

venting materials. Furnace operation can be adversely

affected by restrictive vent and combustion air piping.

The inducer assembly on this furnace can be rotated to

vent the ﬂue products out of the top, left or right side. This

increases the ﬂexibility of which direction the vent pipe

can exit the furnace.

Vent Pipe Material

Vent and combustion air pipe and ﬁttings must be one

of the following materials in the list and must conform to

the indicated ANSI/ASTM standards.

MATERIALS STANDARDS

Schedule 40PVC ......................................................D1785

PVC-DWV .................................................................D2665

SDR-21 & SDR-26 ....................................................D2241

ABS-DWV ................................................................. D2661

Schedule 40 ABS .....................................................F628

Foam / Cellular Core PVC ........................................F891

*PolyPro

by DuraVent ..............................................ULC-S636

*When using PolyPro

, all venting and ﬁttings must be from the same

manufacturer with no interchanging of other materials. Refer to speciﬁc

instructions supplied with the PolyPro vent kits

When joining PVC to PVC, use cement that conforms to

ASTM standard D2564. PVC primer must meet standard

ASTM F656. When joining ABS to ABS, use cement that

conforms to ASTM standard D2235. When joining PVC

to ABS, use cement as speciﬁed in procedure from ASTM

standard D3138

In Canada, all plastic vent pipes and ﬁttings including

any cement, cleaners, or primers must be certiﬁed as a

system to ULC S636. However this requirement does not

apply to the ﬁnish ﬂanges or piping internal to the furnace.

Vent Pipe Length & Diameter

In order for the furnace to operate properly, the combustion

air and vent piping must not be excessively restrictive.

• The ventingsystem shouldbedesignedtohavethe

minimum number of elbows or turns.

• Transitiontothenalventdiametershouldbedoneas

close to the furnace outlet as practical.

• Always use the same size or a larger pipe for

combustion air that is used for the exhaust vent.

Table 1 (page 10) indicates the maximum allowable pipe

length for a furnace of known input rate, when installed

with piping of selected diameter and number of elbows. To

use the table, the furnace input rate, the centerline length

and the number of elbows on each pipe must be known.

When estimating the length of vent runs, consideration

must be made to the effect of elbows and other ﬁttings.

This is conveniently handled using the idea of “equivalent

length”. This means the ﬁttings are assigned a linear

length that accounts for the pressure drop they will cause.

For example: a 2” diameter, long radius elbow is worth

the equivalent of 2.5 feet of linear run. A 90 degree tee

is worth 7 ft.

The equivalent lenghts of tees and various elbows are

listed in Table 1. Measure the linear length of your vent run

and then add in the equivalent length of each ﬁtting. The

total length, including the equivalent ﬁtting lengths, must

be less than the maximum length speciﬁed in the table.

Vent Pipe Installation

CAUTION:

       



This furnace has been certiﬁed for installation with zero

clearance between vent piping and combustible surfaces.

However, it is good practice to allow space for convenience

in installation and service.

• In the absence of local codes, the location of any

combustion air inlet relative to any vent terminal

must be at least 8 inches. This includes installations

involving more than one furnace.

• Thequalityofoutdoorairmustalsobeconsidered.Be

sure that the combustion air intake is not located near a

source of solvent fumes or other chemicals which can

cause corrosion of the furnace combustion system.

(See

page 5 for a sample list of substances).

• Routepipingasdirectaspossiblebetweenthefurnace

and the outdoors. Horizontal piping from inducer to

the ﬂue pipe must be sloped 1/4” per foot to ensure

condensate ﬂows towards the drain tee or PVC trap.

Longer vent runs require larger pipe diameters. Refer

to the Inducer & Venting Options section on page 17

for additional information.

• IfaDirectVent(2-pipe)systemisused,thecombustion

air intake and the vent exhaust must be located in the

same atmospheric pressure zone. This means both

pipes must exit the building through the same portion

of exterior wall or roof as shown in Figure 35 (page 46)

or Figure 40 (page 51).

• Piping must be mechanically supported so that its

weight does not bear on the furnace. Pipe supports

must be installed a minimum of every ﬁve feet along the

vent run to ensure no displacement after installation.

Supports may be at shorter intervals if necessary to

ensure that there are no sagging sections that can trap

condensate. It is recommended to install couplings

along the vent pipe, on either side of the exterior

wall (Figure 35 or Figure 40). These couplings may be

required by local code.

• If breakable connections are required in the

combustion air inlet pipe (if present) and exhaust vent

piping, then straight neoprene couplings for 2” or 3”

piping with hose clamps can be used. These couplings

can be ordered through your local furnace distributor.

To install a coupling:

1. Slide the rubber coupling over the end of the pipe that

is attached to the furnace and secure it with one of the

hose clamps.

2. Slide the other end of the rubber coupling onto the other

pipe from the vent.

3. Secure the coupling with the second hose clamp,

ensuring that the connection is tight and leak free.

Outdoor Terminations - Horizontal Venting

• Vent and combustion air intake terminations shall

be installed as shown in Figure 7 & Figure 8 and in

accordance with these instructions:

• Venttermination clearancesmustbeconsistent with

the NFGC, ANSI 2223.1/NFPA 54 and/or the CSA

B149.1, Natural Gas and Propane Installation Code.

Table 16 (page 43) lists the necessary distances

from the vent termination to windows and building air

intakes.

• Vent and combustion air intake terminations must

be located to ensure proper furnace operation and

conformance to applicable codes. A vent terminal

must be located at least 3 feet above any forced air

inlet located within 10 feet. This does not apply to

the combustion air inlet of a direct vent (two pipe)

appliance. In Canada, CSA B149.1 takes precedence

over these instructions. See Table 17 (page 45).

• Allminimumclearancesmustbemaintainedtoprotect

building materials from degradation by ﬂue gases. See

(Figure 8).

• For optimal performance, vent the furnace through

a wall that experiences the least exposure to winter

winds.

• The vent termination shall be located at least 3 ft.

horizontally from any electric meter, gas meter,

regulator and any relief equipment. These distances

apply ONLY to U.S. installations. In Canada, CSA

B149.1 takes precedence over these instructions.

• Do not installtheventterminal such thatexhaust is

directed into window wells, stairwells, under decks

or into alcoves or similar recessed areas, and do not

terminate above any public walkways.

• Ifventinghorizontally,asidewallventkitisavailable

according to the pipe diameter size of the installation.

For 2 inch pipe use side wall vent kit #904617, and

for 3 inch pipe use kit #904347.   



• Concentricventterminationkitsareavailableforuse

with these furnaces. For 2 Inch pipe use kit #904952

and or 3 inch pipe use kit # 904953. 



• Whentheventpipemustexitanexteriorwallcloseto

the grade or expected snow level where it is not possible

Figure 7. 

12” min. to maximum

expected snow level

(both pipes)

90° Elbow

Exhaust vent

option B

Exhaust vent

option A

Mounting kit faceplate

secured to wall with screws

(both pipes)

Combustion

air inlet

Exhaust vent

option C

18” Min.

36” Max.

8” Min.

36” Max.

(all positions)

Note 2

Mechanical draft

vent terminal

Direct vent

terminal

50,000 Btuh

or less

Forced air inlet

Direct vent

terminal - more

than 50,000 Btuh

Mechanical

draft vent

terminal

Mechanical

draft vent

terminal

Less

than

10 ft.

3 ft.

NOTES:

1. All dimensions shown are

minimum requirements.

2. Exterior vent terminations must

be located at least 12” above the

maximum expected snow level.

Note 2

4 ft

12 in.

9 in.

Note 2

Figure 8. Vent Locations

Figure 9. Alternate Horizontal Vent Installation

Support

NOTE: Vent Configuration to Provide

12" Minimum height above Snow Level.

1/2"

Armaflex

Insulation or

Equivalent

(if required)

12" Above

Maximum

Expected

Snow Level

19" Max.

(See Note)

Outside

Wall

Figure 10. 

Combustion Air

Exhaust Vent

12” Above Maximum

Expected Snow Level

(Both pipes)

Elbows on the combustion air

inlet must be positioned pointing

away from the exhaust vent.

8" Min.

36" Max.

Plumbing Vent Roof Boot

(Both Pipes)

• To prevent debris or creatures from entering the

combustion system, a protective screen may be

installed over the combustion air intake opening. The

screens hole size must be large enough to prevent air

restriction.

Existing Installations

When an existing furnace is removed from a vent system

serving other appliances, the existing vent system may

not be sized properly to vent the remaining appliances

(For example: water heater). An improperly sized venting

system can result in the formation of condensate, leakage,

or spillage. The existing vent system should be checked

to make sure it is in compliance with NFGC and must be

brought into compliance before installing the furnace.

NOTE: If replacing an existing furnace, it is possible you

will encounter an existing plastic venting system that is

subject to a Consumer Product Safety Commission recall.

The pipes involved in the recall are High Temperature

Plastic Vent (HTPV). 

these pipes  This

recall does not apply to other plastic vent pipes, such

as white PVC or CPVC. Check for details on the CPSC

website or call their toll-free number (800) 758-3688.

Condensate Disposal

The method for disposing of condensate varies according

to local codes. Consult your local code or authority having

jurisdiction. Neutralizer kit P/N 902377 is available for

use with this furnace. 



This furnace has multiple options for positioning the vent

pipe as described in the, Vent and Inducer Assembly

Options section (page 17). Each of the condensate

drain lines must be J-trapped using ﬁeld supplied parts.

After the condensate lines are J-trapped, they may be

combined together when routed to the drain.

For Installations where there is limited clearance for the

J-Trap (such as an attic where it may be installed between

ceiling joists), either side of the J-Trap can be shortened

to a minimum of 3 Inches. See Figure 11 (page 16).

to obtain clearances shown in Figure 7, a riser may be

provided as shown in Figure 9 (page 12). Insulation is

required to prevent freezing of this section of pipe. See

Table 3 (page 17) for vent freezing protection.

Outdoor Terminations - Vertical Venting

Termination spacing requirements from the roof and from

each other are shown in

Figure 10. The roof penetration

must be properly ﬂashed and waterproofed with a plumbing

roof boot or equivalent ﬂashing. Vent and combustion air

piping may be installed in an existing chimney which is

not in use provided that:

• Boththeexhaustventandairintakerunthelengthof

the chimney.

• Thetopofthechimneyissealedandweatherproofed.

• The termination clearances shown in

Figure 10 are

maintained.

• Noothergasredorfuel-burningequipmentisvented

through the chimney.

Vent Freezing Protection

CAUTION:



      









icing.

• Table 2 lists the maximum length of ﬂue pipe that can

travel through an unconditioned space or an exterior

space. The total vent length must not exceed the

lengths noted in Table 1 (page 10). For Canadian

installations, please refer to the Canadian Installation

Code (CAN/CGA-B149.1 or 2) and/or local codes.

• Forextremelycoldclimatesorforconditionsofshort

furnace cycles (i.e. set back thermostat conditions)

the last 18 inches of vent pipe can be reduced. It is

acceptable to reduce from 3” to 2-1/2”, 3” to 2”, or 2”

to 1-1/2” if the total vent length is at least 15 feet in

length, and the vent length is within the parameters

speciﬁed in Table 1. The restriction should be counted

as 3 equivalent feet. Smaller vent pipes are less

susceptible to freezing, but must not be excessively

restrictive. The length of the 2 inch pipe must not be

longer than 18 inches.

• If furnace is installed horiziontally, make sure the

drainage port on the in-line drain assembly is pointed

downward to ensure proper drainage of condensate.

For *SC series, see Figure 37 (page 48) & Figure 38

(page 49)

. For *SD & *SD-E series, see Figure 42

(page 53)

WINTER DESIGN

TEMPERATURE

MAXIMUM FLUE PIPE LENGTH (FEET)

IN UNCONDITIONED & EXTERIOR SPACES

WITHOUT INSULATION WITH INSULATION*

20 45 70

0 20 70

-20 10 60

*NOTE: Insulation thickness greater than 3/8 inch, based on an R value

of 3.5 (ft x F x hr) / (BTU x in.)

Vent Protection

CIRCULATING AIR REQUIREMENTS

WARNING:



      

     

     





       







       









       



      











• Plenumsandairductsmustbeinstalledinaccordance

with the Standard for the Installation of Air Conditioning

and Ventilating Systems (NFPA No. 90A) or the

Standard for the Installation of Warm Air Heating and

Air Conditioning Systems (NFPA No. 90B).

• Table 6 (page 34), Table 7 (page 35), Table 8 (page

36)

, Table 9 (page 38), & Table 10 (page 39)

contain the maximum airﬂow and temperature rise

data for each furnace input rate. If the maximum airﬂow

is 1,600 CFM or more, it is recommended that two

openings be used for return air on upﬂow furnaces.

Downﬂow furnaces can only use one return opening.

• It is recommended that the outlet duct contain a

removable access panel. The opening should be

accessible when the furnace is installed in service and

shall be of a size that smoke or reﬂected light may be

observed inside the casing to indicate the presence of

leaks in the heat exchanger. The cover for the opening

shall be attached in a way that prevent leaks.

• If outsideair isused asreturn airto thefurnacefor

ventilation or to improve indoor air quality, the system

must be designed so that the return air is not less than

60° F (15° C) during operation. If a combination of

indoor and outdoor air is used, the ducts and damper

system must be designed so that the return air supply

to the furnace is equal to the return air supply under

normal, indoor return air applications.

• When a cooling system is installed which uses the

furnace blower to provide airﬂow over the indoor coil,

the coil must be installed downstream (on the outlet

side) of the furnace or in parallel with the furnace.

• If a cooling system is installed in parallel with the

furnace, a damper must be installed to prevent chilled

air from entering the furnace and condensing on the

heat exchanger. If a manually operated damper is

installed, it must be designed so that operation of

the furnace is prevented when the damper is in the

cooling position and operation of the cooling system is

prevented when the damper is in the heating position.

• Seal all connections and joints withindustrial grade

sealing tape or liquid sealant. Requirements for sealing

ductwork vary from region to region. Consult with local

codes for requirements speciﬁc to your area.

Return Air Connections

• In applications where the supply ducts carry heated

air to areas outside the space where the furnace is

installed, the return air must be delivered to the furnace

by duct(s) secured to the furnace casing, running full

size and without interruption. 



• Position the furnace with the return air ductwork

ensuring even alignment of furnace (or coil casing)

air opening and return air duct. NOTE: The ductwork

must have an opening equal to that of the return air

opening of the furnace (or coil casing). See Figure

31 (page 32)

or Figure 32 (page 33) for return air

opening size.

Upﬂow & Horizontal Furnaces

• The return air ductwork may be connected to the

left side, right side, or bottom of the furnace. NOTE:

If using the left or right side of the furnace for return

air, the bottom panel (Figure 32) must not be removed

from the bottom of the furnace.

WARNING:















• Side Return Installations: To attach the return air

duct to the left or right side of the furnace, punch out

the 4 knockouts from the side of the furnace (Figure 32).

Using sharp metal cutters, cut an opening between all

4 knockouts to expose the blower assembly. Position

the return air duct over the opening and secure to the

side with sheet metal screws.

•  If using the bottom of

the furnace for return air, the bottom panel (Figure 32)

must be removed from the bottom of the furnace. See

page 21 for removal instructions. Position the furnace

over the return air duct and secure together with sheet

metal screws. Make sure the screws penetrate the

duct and furnace casing.

Downﬂow Furnaces

• Toattachthereturnairducttothefurnace,bendthe

ﬂanges on the furnace upward 90° with wide duct

pliers. See Figure 31 for furnace ﬂange locations.

NOTE: If system installation includes AC coil casing,

bend the ﬂanges on the coil casing upward 90° before

attaching the return air duct.

• Securethereturnairductworktothefurnaceorcoil

casing (if installed) with sheet metal screws. Make

sure the screws penetrate the sheet metal casing and

ﬂanges.



• The supply air must be delivered to the heated space

by duct(s) secured to the furnace or coil box casing,

running full size and without interruption.

• To attach the supply air duct to upﬂow & horizontal

furnaces, bend the ﬂanges on the furnace upward 90°

with wide duct pliers. See Figure 32 for furnace ﬂange

locations. NOTE: If system installation includes AC coil

casing, bend the ﬂanges on the coil casing upward 90°

before attaching the supply air duct.

• Position the supply air ductwork onto the furnace

ensuring even alignment of furnace air opening and

supply air duct. NOTE: The ductwork must have an

opening equal to that of the supply air opening of the

furnace. See Figure 31 (page 32) and Figure 32 (page

33)

for supply air opening size.



Damping ducts, ﬂexible vibration isolators, or pleated

media-style ﬁlters on the return air inlet of the furnace

may be used to reduce the transmission of equipment

noise eminating from the furnace. These treatments can

produce a quieter installation, particularly in the heated

space. However, they can increase the pressure drop in

the duct system. Care must be taken to maintain the proper

maximum pressure rise across the furnace, temperature

rise and ﬂow rate. This may mean increasing the duct size

and/or reducing the blower speed. These treatments must

be constructed and installed in accordance with NFPA and

SMACNA construction standards. Consult with local codes

for special requirements. For best sound performance,

install all the needed gaskets and grommets around

penetrations into the furnace, such as for electrical wiring.

FURNACE INSTALLATION

*SC , *SD & *SD-E series gas furnaces offer a wide range

of installation options, including installation in the upﬂow or

horizontal positions with either right, left, or upﬂow return

air. *SL & *SM series gas furnaces may only be installed

as a downﬂow application.



• The furnace must be leveled at installation and

attached to a properly installed duct system. See

Figure 1 (page 6) for the required clearances needed

to move the furnace to its installation point (hallways,

doorways, stairs, etc).

• The furnace must be installed so that all electrical

components are protected from water.

• The furnace must be installed upstream from a

refrigeration system. (If applicable)

• Thecabinetplugmustalwaysbeusedtoclosethehole

in the side of the furnace when rotating the inducer.

• The furnace requires special venting materials and

installation procedures. See

page 7, page 8, page

, page 10, page 11, page 12, & page 13 for

venting guidelines and speciﬁcations.

Upﬂow Furnaces

WARNING:

      



than wood ﬂooring.

*SC, *SD & *SD-E series gas furnaces are shipped with

the bottom panel installed as shown in

Figure 32 (page

33)

. If the furnace is installed with side return air, the

bottom panel must not be removed. If the furnace is

installed with bottom return air, the bottom panel must

be removed. See Bottom Panel Removal on page 21.

Horizontal Furnaces

WARNING:

      



than wood ﬂooring.

*SC, *SD & *SD-E series gas furnaces can be installed

horizontally (Figure 11) in an attic, basement, crawl space

or alcove. It can also be suspended from a ceiling in a

basement or utility room in either a right to left airﬂow or

left to right airﬂow as shown in Figure 12 (page 16).

These furnaces are shipped with the bottom panel installed.

If the furnace is installed horizontally, remove the bottom

panel from the furnace before attaching the duct system.

See Bottom Panel Removal on

page 21.

If installing the furnace with an evaporator coil (in an attic),

it is required that a drip pan be placed under the furnace.

If the installation is on a combustible platform as shown

Figure 11, it is recommended that the drip pan extend

at least 12 inches past the top and front of the furnace.

NOTE: Although it is not required to use a drip pan for heat

only applications, state and local codes may require it.

If suspending the furnace from the ceiling, assemble a

support frame (Figure 12) using slotted iron channel and

full threaded rod. Fasten the frame together with nuts,

washers, and lockwashers. Secure the support frame to the

rafters with lag bolts. The furnace can also be suspended

using steel straps around each end of the furnace. The

straps should be attached to the furnace with sheet metal

screws and to the rafters with bolts.

It is recommended for further reduction of ﬁre hazard

that cement board or sheet metal be placed between the

furnace and the combustible ﬂoor and extend 12 inches

beyond the front of the door and top of the furnace.

Special Instructions for SC038-23A Furnaces

If installing an SC038-23A furnace horizontally (with

airﬂow going from left to right), the pressure switch will

need to be moved to the side of the furnace that is not

facing the ground. See Figure 13. Moving the switch will

make it easier to replace in the future.

Figure 12. 

Lag

Bolt

Nuts (x2)

Washer

and

Lockwasher

Nuts (x2)

Threaded

Rod

1. Shut off any electrical power to the furnace.

2. Label and disconnect the tubing and wires from the

pressure switch (1).

3. Remove two screws (2) securing the pressure switch

(1) to the side of the furnace.

4. Remove two 1/4” black plugs (3) on the opposite side

of the cabinet that the pressure switch will be relocated

to.

5. Position the pressure switch (1) in its new location and

secure it in place using the same screws (2) removed

in step 2

6. Insert the plugs (3) into the holes on the side that the

pressure switch (1) was removed from.

7. Reconnect the tubing and wiring to the pressure switch

(1) being careful that they will not fall into the burner

box.

CAUTION:





        



8. Check the furnace for proper operation as directed in

Startup and Adjustments section. If the furnace shuts

down during the pre-purge, the switch that measures

pressure in the header needs to be checked for correct

tubing connections.

Downﬂow Furnaces

WARNING:

      



than wood ﬂooring.

Flue pipe vented

to outside

J-Trap

Height

3” Min.

Coil Plenum

Wood or

non-combustible

platform

Two-pipe installation shown

Combustion Air

Condensate

Drain Lines

Figure 11. 

Figure 13. SC038-23A Pressure Switch

PLUGS (X2)

PRESSURE

SWITCHES

SCREWS (X2)

WARNING:





To install an *SL & *SM series gas furnace on combustible

ﬂooring, a special sub-base is required. Downﬂow sub-

base kits are factory supplied accessories and are listed

according to the cabinet letter of the furnace. For ‘B’, ‘C’,

and ‘D’ size cabinets use Kit #904911. 



A downﬂow sub-base kit is not necessary if the furnace

is installed on a factory or site-built cased air conditioning

coil. However, the plenum attached to the coil casing

must be installed so that its surfaces are at least 1” from

combustible construction.

Installation on a Concrete Slab

1. Create an opening in the ﬂoor according to the

dimensions in Table 3.

2. Position the plenum and the furnace as shown in

Figure 14.

Figure 14. 

Concrete

Floor

Furnace

Sheet

Metal

Plenum



MODEL # DIM. “A” DIM. “B”

054D-24B 16 5/8 19 1/4

072D-24B 16 5/8 19 1/4

072D-35C 20 1/8 19 1/4

090D-35C 20 1/8 19 1/4

118D-45D 23 5/8 19 1/4

120D-45D 23 5/8 19 1/4

NOTE: Dimensions shown in Inches.

“A”

“B”

Opening in concrete floor

Inducer & Venting Options

To increase installation ﬂexibility, the inducer assembly can

be rotated up to 3 different positions. Each variation has

slightly different requirements with regard to condensate

disposal and, in some cases, the need to seal the furnace

cabinet.

IMPORTANT NOTE:





Before using Table 4, the number of pipes (1-pipe or 2-pipe)

connected to the furnace must be known. Find the proper

furnace style (upﬂow, horizontal, or downﬂow) and then

the side that the pipes will exit from the furnace. Finally

select the option that properly matches your installation

type. For *SC & *SL series, Figure 35, Figure 36, Figure 37,

Figure 38, or Figure 39. For *SD, *SD-E & *SM series, see

Figure 40, Figure 41, Figure 42, or Figure 43.

NOTE: It is important that Direct Vent (2-pipe) systems

maintain an airtight ﬂow path from the air inlet to the ﬂue

gas outlet. The furnace ships from the factory with two

holes in the cabinet for the air inlet and ﬂue gas outlet.

In certain conﬁgurations, it is necessary to remove and

relocate a plastic plug in the furnace cabinet. If changing

the position of the air inlet and ﬂue gas outlet, it is required

that the previous hole be closed off with the plastic plug to

maintain air tightness in the furnace. The hole locations

for all furnace series are shown in

Figure 31 and Figure 32.



VENT

DIRECTION

UPFLOW

HORIZONTAL

RIGHT

HORIZONTAL

LEFT

DOWNFLOW

Right

Option 21

N/A N/A

Option 29

Up N/A

Option 25 Option 26 Option 30

Left

Option 22

N/A N/A

Option 31



VENT

DIRECTION

UPFLOW

HORIZONTAL

RIGHT

HORIZONTAL

LEFT

DOWNFLOW

Right

Option 23

N/A N/A

Option 32

Up N/A

Option 27 Option 28 Option 33

Left

Option 24

N/A N/A

Option 34

Vent & Inducer Blower Options

*SC & *SL SERIES - CONVENTIONAL (1 PIPE)

VENT

DIRECTION

UPFLOW

HORIZONTAL

RIGHT

HORIZONTAL

LEFT

DOWNFLOW

Option 1 Option 7 Option 10 Option 15

Right

Option 2 Option 8

N/A

Option 16

Left

Option 3

N/A

Option 9 Option 17

*SC & *SL SERIES - DIRECT VENT (2-PIPE)

VENT

DIRECTION

UPFLOW

HORIZONTAL

RIGHT

HORIZONTAL

LEFT

DOWNFLOW

Option 4 Option 12 Option 14 Option 18

Right

Option 5 Option 11

N/A

Option 19

Left

Option 6

N/A

Option 13 Option 20

Inducer Assembly Rotation

WARNING:

     



 

     



CAUTION:

         



and dangerous operation.

1. Disconnect the electrical harness from the inducer

assembly.

2. Remove the inducer assembly ground wire from the

blower deck.

3. Remove 3 screws securing the inducer assembly to the

header box.

4. Rotate the inducer assembly to its new position.

5. Secure the inducer assembly to the header box by

reinstalling the three screws. If the inducer assembly

is rotated to the left or right side of the furnace, use the

extra screw provided in the parts package.

6. Remove the cabinet plug from side of furnace and

reinstall in hole on opposite side of cabinet.

7. Install in-line drain assembly and tubing.

8. Install all condensate drain lines. For *SC & *SL series,

refer to Figure 35, Figure 36, Figure 37, Figure 38, or Figure

39.

For *SD, *SD-E & *SM series, refer to Figure 40,

Figure 41, Figure 42, or Figure 43.

9. Reconnect the electrical harness to the inducer

assembly.

10. Reconnect the inducer assembly ground wire to the

blower deck or door.

11. Verify operation as detailed on the furnace label.

Pressure Switch Tubing

All upﬂow / horizontal furnaces have two switches, one

connected to the static tap on the inducer assembly and

the other to the collector box. Figure 15 & Figure 16 display

the proper routing of pressure switch tubing for *SC, *SD

& *SD-E furnaces. Downﬂow (*SL & *SM) furnaces require

only one switch connected to the inducer’s static tap as

shown in

Figure 17.

Alternate Pressure Switch Location

In some inducer orientations, the inducer pressure switch

may interfere with gas pipe installation. Determine the

side of the cabinet the gas pipe will enter and see if the

inducer pressure switch needs to be moved. If the pressure

switch interferes with the gas pipe, use these instructions

for relocating it to an alternate location:

Figure 15. 



Figure 16. 

Upﬂow Furnaces





Figure 17. 

Downﬂow Furnaces





Accessories

The components below are included in the extra parts

bag that is supplied with the purchase of your furnace.

Depending on your particular installation, some of these

components are optional and may not be used. Please

refer to the descriptions and accompanying ﬁgures when

installing these items. NOTE: Some parts may not be

supplied with each furnace. Refer to the literature in the

extra parts bag for the parts included witht he particular

furnace.

Finish Flange

The ﬁnish ﬂange must be installed to vent the combustion

air pipe through the top of the furnace. NOTE: For proper

installation it is important that the pipe and screw holes

in the ﬁnish ﬂanges, gasket, and cabinet are aligned.

See Figure 19.

1. Position ﬂange gasket over hole in the furnace cabinet.

2. Position ﬁnish ﬂange on top of the ﬂange gasket.

NOTE: Make sure the ﬂange is properly oriented so

that the FRONT lettering is located near the front of

the furnace as shown in Figure 19.

3. Secure ﬂange and gasket to cabinet with three ﬁeld

supplied sheet metal screws.

Rubber Grommets

The 2 1/4” rubber grommet is used to seal the opening

between the furnace cabinet and the 2” PVC vent pipe.

The rubber grommet should be installed in the 3” hole

prior to running the vent pipe out of cabinet. No sealants

are required. See Figure 20.

The 7/8” rubber grommet is used to seal the opening

between the furnace cabinet and the gas pipe. The rubber

grommet should be installed in the 1 5/8” hole prior to

running the gas pipe into the cabinet. No sealants are

required.

The 3/4” rubber grommet is used if venting out the left

side of the cabinet and the drain tube is routed through

the blower deck. Remove the plastic plug from the hole

and install the grommet before routing the drain tube.

1. Shut off any electrical power to the furnace.

2. Label and disconnect the tubing and wires from the

pressure switch (Figure 18).

3. Remove two screws securing the pressure switch to

the inducer housing.

4. Remove the pressure switch from the mounts on the

inducer housing and relocate it to the other set of mounts

90° from previous location.

5. Secure the pressure switch with two screws.

6. Reconnect the tubes and wires to the pressure switch.

Figure 18. Alternate Pressure Switch Location

PRIMARY

LOCATION

ALTERNATE

LOCATION

Figure 20. 

Ø 3/4” Rubber

Grommet

ø 2 1/4” Rubber Grommet

(see note)

ø 7/8” Rubber

Grommet

Figure 19. Finish Flange

Finish

Flange

Gasket

Hole for

Flue

Vent Pipe

Hole for Inlet

Air Vent Pipe

FRONT

FRONT lettering must be

located near front

of furnace

3. Install the 1/2” x 1/2” hose barb on the 2” PVC reducer.

NOTE: Do not over tighten! Use an adequate amount of

Teﬂon tape on the threads. Do not use liquid sealants.

4. Verify all connections and joints for tight ﬁt and proper

alignment with other vent pipes.

Alternate Orientation

1. Install the 2” PVC Tee horizontally on the 2” vent pipe that

is extending out the side of the cabinet. Permanently bond

them together using appropriate primer and cement.

Refer to the alternate orientation shown in

Figure 21.

2. Install the 2” PVC Elbow on the end of the 2” PVC Tee.

Permanently bond them together using appropriate

primer and cement.

3. Install the reducer or PVC trap (if supplied) on the bottom

end of the PVC Tee. Permanenly bond them together

using appropriate primer and cement.

4. Install the 1/2” x 1/2” hose barb on the 2” PVC reducer.

NOTE: Do not over tighten! Use an adequate amount of

Teﬂon tape on the threads. Do not use liquid sealants.

5. Verify all connections and joints for tight ﬁt and proper

alignment with other vent pipes.

Optional PVC Pipe Installation

When running the 2” PVC pipe out through the top of

the *SD or *SD-E upﬂow furnace, there may be possible

clearance issues when transitioning the PVC pipe from

2” to 3”:

• IfthesizeofthePVCueneedstobeincreasedfrom

2” to 3”, two, 2” x 45° PVC elbows may be used to

achieve the clearances needed between the coil box

and the 2” x 3” coupling. See

Figure 22 (page 21).

• Install the2” x3” couplingin thevertical run only. If

the coupling is installed horizontally, it will allow water

to build up inside the furnace and cause a lock out

condition.

• Toavoidtheclearanceissue,itisrecommendedthat

the furnace be vented through the left side or the right

side of the cabinet.

Condensate Drain Lines

















• Themethodfordisposingcondensatevariesaccording

to local codes. Consult your local code or authority

having jurisdiction.

• The condensate drain line must be trapped using

a kit (P/N- 922485) or ﬁeld supplied parts. After the

drain trap, condensate can continue to the drain by

connecting to a recommended 3/4” ID minimum drain

line, but no smaller than the original tubing ID supplied

by the manufacturer. The drain line should slope

downward away from the furnace to ensure proper

drainage.

PVC Components

IMPORTANT NOTES:

 





 Figure 21 are not







The 2” PVC tee, reducer, PVC Trap and 1/2” X 1/2” hose

barb are used when the inducer is rotated to vent out thru

the left or right side of the furnace cabinet. See Figure 21.

The 1/2” X 3/4” hose barb can be used to route the

condensate drain to the outside of the cabinet. It must

be installed from inside the cabinet with the threaded

end inserted thru the 1 1/16” hole. The condensate drain

should be connected to the barbed end. Attach 1” PVC

drain line to the threaded end. See Figure 31 (page 32)

or Figure 32 (page 33) for hole location.

Typical Orientation

1. Install the PVC Tee vertically on the 2” vent pipe that is

extending out the side of the cabinet. Permanently bond

them together using appropriate primer and cement.

Refer to the typical orientation shown in Figure 21.

2. Install the reducer or PVC trap (if supplied) on the bottom

end of the PVC Tee. Permanently bond them together

using appropriate primer and cement.

Figure 21. 

1/2” x 3/4”

Hose Barb

2” PVC Elbow

(Field Supplied)

2” PVC Te e

1/2” x 3/4”

Hose Barb

2” PVC Pipe from Inline

Drain Assembly

(Not Included)

1/2” Tubing Formed

into a Loop

(Field Supplied)

PVC

Trap

INSTALLATION OF PVC COMPONENTS

(TYPICAL ORIENTATION)

INSTALLATION OF PVC COMPONENTS

(ALTERNATE ORIENTATION)

2” PVC Te e

2” PVC Pipe from Inline

Drain Assembly

(Not Included)

1/2” Tubing Formed

into a Loop

(Field Supplied)

PVC

Trap

La page charge ...

Maytag FG7S(C,L) Guide d'installation

Marque: Maytag

Modèle: FG7S(C,L)

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag FG7S(C,L) Installation guide

Maytag FG7S(C,L) Guide d'installation

Ce manuel convient également à

Maytag FG7S(C,L) Guide d'installation

dans d''autres langues

Documents connexes

Autres documents