REOLINK E1 Zoom Mode d'emploi

Marque: REOLINK

Modèle: E1 Zoom

Taper: Mode d'emploi

December 2020

QSG3_B

58.03.001.0156

Reolink E1 Zoom

Quick Start Guide

@ReolinkTech https://reolink.com

Contents

What’s in the Box

Camera Introduction

Set up the Camera

Mount the Camera

Troubleshooting

Speciﬁcations

Notiﬁcation of Compliance

1 English

What’s in the Box

2English

Reset Needle

(For E1 Zoom only)

Reolink E1

Series Camera

Quick

Start Guide

Pack of Screws

Surveillance

Sign

Mounting

Hole Template

Mounting Plate Power Adapter

Speaker

Power Port

Micro SD Card Slot

Daylight Sensor

Camera Introduction

Built-in Mic

Status LED

Lens

Reset Button

*Rotate the lens to ﬁnd the reset

button and the SD card slot.

4English3 English

Meaning of the Status LED:

• On Smartphone

Download and Launch the Reolink App or Client software

and follow the onscreen instructions to ﬁnish initial setup.

Scan to download the Reolink App.

Set up the Camera

• On PC

Download path of the Reolink Client: Go to

https://reolink.com > Support > App & Client.

Available on the

WiFi connection failed

Status/LED LED in Blue

WiFi is not conﬁgured

Camera is starting up

WiFi connection succeeded

Blinking

Mount the Camera

Step 1

Drill two holes on the

wall according to the

mounting hole

template.

Step 2

Insert the two plastic

anchors into the holes.

Step 3

Secure the base unit in

place by tightening the

screws into the plastic

anchors.

Step 4

Align the camera with

the bracket and turn the

camera unit clockwise

to lock it in position.

NOTE:

1. To remove it from the

wall, turn the camera

anticlockwise.

2. In case your camera is

mounted upside down, its

picture shall be rotated

as well. Please go to

Device Settings ->

Display on Reolink

app/Client and click

Rotation to adjust the

image.

6English

5 English

If your camera is not powering on, please try the

following solutions:

• Plug the camera into another outlet.

• Use another 5V power adapter to power up the camera.

If these won't work, please contact Reolink Support

https://support.reolink.com/.

Troubleshooting

Camera Is Not Powering on

If the camera failed to scan QR code on your phone,

please try the following solutions:

• Remove the protective ﬁlm from the camera lens.

• Wipe the camera lens with a dry paper/towel/tissue.

• Vary the distance (about 30cm) between your camera

Failed to Scan QR Code on Smartphone

8English7 English

Tips for Camera Placement

• Do not face the camera towards any light sources.

• Do not point the camera towards a glass window. Or, it

may result in poor image performance because of the

window glare by infrared LEDs, ambient lights or status

lights.

• Do not place the camera in a shaded area and point it

towards a well-lit area. Or, it may result in poor image

performance. For better image quality, please make sure

that the lighting condition for both the camera and the

capture object is the same.

• For better image quality, it’s recommended to clean the

lens with a soft cloth from time to time.

• Make sure the power ports are not exposed to water or

moisture or blocked by dirt or other elements.

and the mobile phone, which enables the camera to

focus better.

• Try scanning the QR code under a brighter atmosphere.

If these won't work, please contact Reolink Support

https://support.reolink.com/.

If the camera fails to connect to WiFi, please try the

following solutions:

• Please make sure the WiFi band meets the network

requirement of the camera.

• Please ensure you have entered the correct

WiFi password.

• Put your camera close to your router to ensure a

strong WiFi signal.

• Change the encryption method of the WiFi network to

WPA2-PSK/WPA-PSK (safer encryption) on your router

interface.

• Change your WiFi SSID or password and make sure

that SSID is within 31 characters and password is within

64 characters.

• Set your password using only the characters on the

keyboard.

If these won't work, please contact Reolink Support

https://support.reolink.com/.

WiFi Connection Failed During Initial

Setup Process

10English9 English

Display Resolution:

5MP(E1 Zoom)/4MP(E1 Pro)/3MP(E1)

IR Distance: 12 meters (40ft)

Pan/Tilt Angle: Horizontal: 355°/Vertical: 50°

Power Input: DC 5V/1A

Hardware

Speciﬁcations

12English

11 English

Frame Rate: 15fps (default)

Audio: Two-way audio

IR Cut Filter: Yes

Software Features

Operating Frequency:

2.4 GHz (E1)/Dual-band (E1 Pro/E1 Zoom)

Operating Temperature: -10°C to 55°C (14°F to 131°F)

Size: Φ76 x 106 mm

Weight: 200g (E1/E1 Pro)/250g(E1 Zoom)

General

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

• this device may not cause harmful interference, and

FCC Compliance Statement

Notiﬁcation of Compliance

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment o

and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

• this device must accept any interference received,

including interference that may cause undesired

operation.

14English13 English

This product comes with a 2-year limited warranty that

is valid only if purchased from Reolink ocial stores or a

Reolink authorized reseller. Learn more:

https://reolink.com/warranty-and-return/.

Limited Warranty

This equipment complies with FCC radiation exposure

limits set forth for an uncontrolled environment. This

equipment shall be installed and operated with minimum

distance 20cm between the radiator & body.

FCC RF Exposure Warning Statements

Reolink declares that this device is in compliance with

the essential requirements and other relevant provisions

of Directive 2014/53/EU.

This marking indicates that this product should not be

disposed with other household wastes throughout the

EU. To prevent possible harm to the environment or

human health from uncontrolled waste disposal, recycle

it responsibly to promote the sustainable reuse of

material resources. To return your used device, please

use the return and collection systems or contact the

retailer where the product was purchased. They can take

this product for environment safe recycling.

Simpliﬁed EU Declaration of Conformity

Correct Disposal of This Product

NOTE: We hope that you enjoy the new purchase. But if

you are not satisﬁed with the product and plan to return,

receiver.

• Connect the equipment into an outlet on a circuit

dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV

technician for help.

Changes or modiﬁcations not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.

16English15 English

Use of the product is subject to your agreement to the

Keep out of the reach of children.

Terms and Privacy

By using the Product Software that is embedded on the

Reolink product, you agree to the terms of this End User

License Agreement (“EULA”) between you and Reolink.

Learn more: https://reolink.com/eula/.

End User License Agreement

This device contains licence-exempt transmitter(s)/

receiver(s) that comply with Innovation, Science and

Economic Development Canada’s licence-exempt RSS(s).

ISED Statements

The device has been evaluated to meet general RF

exposure requirements. The device can be used in

Radio Frequency Exposure Statement for IC

we strongly suggest that you reset the camera to

factory default settings and take out the inserted SD

card before returning.

Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including

interference that may cause undesired operation of the

device.

L’émetteur/récepteur exempt de licence contenu dans le

présent appareil est conforme aux CNR d’Innovation,

Sciences et Développement économique Canada

applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes:

(1) L' appareil ne doit pas produire de brouillage;

(2) L' appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible

d' en compromettre le fonctionnement.

18English17 English

OPERATING FREQUENCY

2412MHz-2462MHz

5180MHz-5240MHz

5745MHz-5825MHz

Technical Support

If you need any technical help, please visit our official

support site and contact our support team before

returning the products https://support.reolink.com/.

mobile exposure conditions. The min separation distance

is 20cm.

Déclaration d'exposition aux radiofréquences pour IC

L'appareil a été évalué pour répondre aux exigences

générales en matière d'exposition aux RF. L'appareil peut

être utilisé dans des conditions d'exposition mobiles. La

distance de séparation minimale est de 20cm.

Operation of this device is restricted to indoor use only.

(5180-5240MHz)

Le fonctionnement de cet appareil est limité à une

utilisation en intérieur uniquement. (5180-5240MHz)

REOLINK E1 Zoom Mode d'emploi

Marque: REOLINK

Modèle: E1 Zoom

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: REOLINK E1 Zoom User guide

Documents connexes

Autres documents

SGIN T10 Manuel utilisateur