Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are
trademarks of Anker Innovations Limited, registered in the United States and other
countries. All other trademarks are the property of their respective owners.
51005002777 V01
QUICK
START GUIDE
SoloCam L20 / L40
EN 01
TABLE OF
CONTENTS
PRODUCT OVERVIEW 02
CHARGING SOLOCAM 03
SETTING UP SOLOCAM 04
05 MOUNTING SOLOCAM
08 NOTICE
02 EN EN 03
PRODUCT
OVERVIEW
1
2
35
4
1. Camera Lens 4. LED Indicator
2. Motion Sensor 5. Microphone
3. Photosensitive Sensor 6. Mounting Hole
7. SYNC Button 9. Speaker
8. Type-C Charging Port
CHARGING
SOLOCAM
Battery-powered
Charging Solid blue
Fully charged Off
6
7
8
9
04 EN EN 05
SETTING UP
SOLOCAM
Download the App and Set up the System
1. Download and install the eufy Security app, and sign up for an account.
2. Follow on-screen instructions to add your SoloCam .
MOUNTING
SOLOCAM
Select a Location
SoloCam L20 / L40 can be mounted on a wall or ceiling. Select a location
where you can get the desired view. We recommend hanging it 7-10 ft
(2-3 m) above the ground.
Motion
Detection
Zone
Camera field
of view
Up to 26 ft (8 m)
7-10 ft
(2 - 3 m)
Motion
Detection
Zone
Camera field
of view
06 EN EN 07
Mount SoloCam L20 / L40
SoloCam L20 / L40 can be mounted both outdoors and indoors.
1. Turn the knob of the mounting bracket counterclockwise to loosen
and disassemble it.
2. Place the mounting bracket against the wall. Drill holes with a 15/64
inch (5.99 mm) drill bit, then insert the anchors into the holes; anchors
are necessary for walls that are made out of hard materials such as
concrete, brick, or stucco.
3. Firmly screw the knob of the mounting bracket into the mounting hole
of SoloCam.
4. Hold and screw SoloCam to the mounting bracket. Rotate SoloCam
to adjust the view and check it using the live stream which you can
access in the eufy Security app.
SoloCam L20 / L40 can be also installed on the ceiling. Follow the steps 1-4
mentioned above to install it.
Tips:
For troubleshooting, check Help on the eufy Security app. Refer to the
app page for LED indicator status.
08 EN EN 09
NOTICE
IC StatementThis device complies with Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions:(1) this device may not cause interference, and(2) this
device must accept any interference, including interference that may cause undesired operation of
the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC RF Statement
When using the product, maintain a distance of 20cm from the body to ensure compliance with RF
exposure requirements.
Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux
exigences en matière d'exposition RF
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates,uses and can radiate radio frequency energy and,if not installed and
used in accordance with the instructions,may cause harmful interference to radio communications.
However,there is no guarantee that interference will not occur in a particular installation.If this
equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: (1) Reorient or relocate
the receiving antenna. (2) Increase the separation between the equipment and
receiver. (3) Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. (4) Consult the dealer or an experienced radio/
TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in
fixed/mobile exposure condition. The min separation distance is 20 cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain
compliance with FCC regulations.
The following importer is the responsible party.
Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8TH ST, STE 501, BELLEVUE, WA 98004
Telephone: 1-800-988-7973
10 EN
Customer Service
Warranty
12-month limited warranty
Call Us
United States
+1 (800) 988 7973 Mon-Fri 9AM-5PM (PT)
United Kingdom
+44 (0) 1604 936 200 Mon-Fri 6AM-11AM (GMT)
Germany
+49 (0) 69 9579 7960 Mon-Fri 6:00-11:00
Email Us
Customer Support: [email protected]
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok,
Kowloon, Hong Kong
@EufyOfficial
@EufyOfficial
@EufyOfficial
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
dans d''autres langues
- English: Eufy L20-L40 User guide
Documents connexes
-
Eufy T87A0 Mode d'emploi
-
Eufy C22 Solo Outdoor Cam Mode d'emploi
-
Eufy E8453JW1 Mode d'emploi
-
Eufy T8441 Mode d'emploi
-
-
-
Eufy B09CKZNHJL Mode d'emploi
-
-
-