(a)If the display is OFF, press the button would wake up the display,

And the display show the status of fan, light or timing by flickering.

(b)If the display is ON, the display would be bright for 10s and show

the status of fan, light or timing after you press the button.

②F/R: Press and hold the button for 2s to change the direction of

fan. And the display would show the direction of fan.

(Forward/Summer: Reversal/Winter: )

③NATURAL WIND ON/OFF:

(a)The natural wind mode: the fan run from speed level 1 increase

to level 3 slowly in 10s, and then from speed level 3 decrease to

(d)If the fan is ON and is in the natural wind mode, the fan will exit

the natural wind mode and run in the last speed when you press this

button. And the display will show the fan speed.

④TIMING:

(a)If the fan is OFF, this button is useless, The display will show "0"

when you press this button.

(b)If the fan is ON or is in the natural wind mode, it will set the

timing increase 1 hour when you press this button. And the display

will show the timing.(The timing of display cycles from 0 to 9.)

(c)If the fan is ON or is in the natural wind mode, it will cancel the

(a)Press and hold on this button less then 1s, the function is open or

close the temperature control. And the display will show the status of

temperature control.

(open temperature control: close temperature control: )

(b)When you would like to operate ceiling fan by remote controller,

you need to press and hold on this button more then 1s to code within

the receiver powered in 10s. You would hear a sound “beep” if the

controller codes with receiver successfully.

(c)If you press and hold on this button more then 1s, the display will

show “ ”.

⑥SPEED UP:

(a)If the fan is ON and is in natural wind mode, the fan will exit the

will show the fan speed level. (The maximum speed level is 6.)

⑦SPEED DOWN:

(a)If the fan is ON and is in natural wind mode, the fan will exit the

natural wind and decrease one speed level based on the speed

level before entering natural wind mode when you press this

button. The display will show the fan speed level. (The minimum

speed level is 1.)

(b)If the fan is ON and is not in natural wind mode, the fan will

decrease one speed level when you press this button. The display

will show the fan speed level. (The minimum speed level is 1.)

⑨LIGHT ON/OFF:

(a)If the light is OFF, the light will be turned on with the last

show the luminance level.

(b)If the light is ON, the light will be turned off when you press this

button. And the display will show “0”.

⑩BRIGHTNESS UP:

(a)If the light is OFF, this button is useless. And the display will show

“0” when you press this button.

(b)If the light is ON, The luminance will increase one level when you

press this button. And the display will show the luminance level.

(The maximum luminance level of display is 9.)

⑪BRIGHTNESS DOWN:

(a)If the light is OFF, this button is useless. And the display will don’t

show anything when you press this button.

(b)If the light is ON, change the color temperature to warm when

you press this button. But the display will don’t show anything.

⑬WHITE BUTTON:

(a)If the light is OFF, this button is useless. And the display will don’t

show anything when you press this button.

(b)If the light is ON, change the color temperature to neutral when

you press this button. But the display will don’t show anything.

⑭BLUE BUTTON:

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

Changes or modifications to this unit not expressly approved by the

party responsible for compliance could void the user’s authority to

operate the equipment.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for

and Economic Development Canada’s licence-exempt RSS(s). Operation

two conditions:

(1) This device may not cause interference.

operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil

est conforme aux CNR

d’Innovation, Sciences et Développement économique Canada

exempts de licence. L’exploitation est autorisée aux deux conditions

suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi, même si

le brouillage est susceptible

d’en compromettre le fonctionnement.