NEC GT1150 Series Manuel utilisateur

LCD Projector

GT1150

User’s Manual

Printed in Japan

7N8P0112

GT1150 User's ManualNEC

R

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

SELECT

LENS SHIFT

LEFT

ZOOM

FOCUS

UP

DOW

N

RIGHT

A

U

T

O

A

D

J

U

S

T

L

A

M

P

S

T

A

T

U

S

P

O

W

E

R

O

N

/S

T

A

N

D

B

Y

S

O

U

R

C

E

LCD Projector

GT1150

User’s Manual

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

U.S. Responsible Party:

Address:

Tel. No.:

NEC Technologies, Inc.

1250 N. Arlington Heights Road

Itasca, Illinois 60143

(630) 467-5000

Type of Product:

Equipment Classification:

Models:

LCD Projector

Class B Peripheral

GT1150

We hereby declare that the equipment specified above

conforms to the technical standards as specified in the FCC Rules.

E – ii

IMPORTANT INFORMATION

Precautions

Please read this manual carefully before using your NEC GT1150 Pro-

jector and keep the manual handy for future reference.

Your serial number is located on the bottom of your GT1150. Record it

here:

CAUTION

To turn off main power, be sure to remove the plug from

power outlet.

The power outlet socket should be installed as near to

the equipment as possible, and should be easily acces-

sible.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED NEC SERVICE

PERSONNEL.

This symbol warns the user that uninsulated voltage

within the unit may be sufficient to cause electrical shock.

Therefore, it is dangerous to make any kind of contact

with any part inside of the unit.

This symbol alerts the user that important information

concerning the operation and maintenance of this unit

has been provided. The information should be read care-

fully to avoid problems.

WARNING

TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE.

DO NOT USE THIS UNIT’S GROUNDED PLUG WITH AN EXTEN-

SION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS CAN

BE FULLY INSERTED.

DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COM-

PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALI-

FIED NEC SERVICE PERSONNEL.

DOC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

3. GSGV Acoustic Noise Information Ordinance:

The sound pressure level is less than 70 dB (A) according to ISO 3744

or ISO 7779.

RF Interference

WARNING

The Federal Communications Commission does not allow any

modifications or changes to the unit EXCEPT those specified by

NEC Technologies in this manual. Failure to comply with this gov-

ernment regulation could void your right to operate this equip-

ment.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equip-

ment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. How-

ever, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful inter-

ference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following mea-

sures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

In UK, a BS approved power cable with moulded plug has a Black (five

Amps) fuse installed for use with this equipment. If a power cable is not

supplied with this equipment please contact your supplier.

• IBM is a registered trademark of International Business Machines

Corporation.

• Macintosh and PowerBook are registered trademarks of Apple Com-

puter, Inc.

• Other product and company names mentioned in this user's manual

may be the trademarks of their respective holders.

E – iii

INFORMATIONS IMPORTANTES

Précautions

Veuillez lire ce manuel avec attention avant d’utiliser votre projecteur

NEC GT1150 et gardez ce manuel à portée de main afin de pouvoir y

recourir facilement.

Votre numéro de série est situé sur le fond de votre GT1150. Reportez-

le ici:

ATTENTION

Pour couper complètement l’alimentation, retirez la prise

du secteur.

La prise du secteur doit être accessible et installée le

plus près possible de l’appareil.

ATTENTION

POUR ÉVITER TOUT CHOC ÉLECTRIQUE, N’OUVREZ PAS LE

BOÎTIER. LES PIÈCES INTERNES NE SONT PAS RÉPARABLES

PAR L’UTILISATEUR. POUR TOUTE RÉPARATION, ADRESSEZ-

VOUS À UN RÉPARATEUR AGRÉE NEC.

Ce symbole avertit l’utilisateur que le contact avec

certaines parties non isolées à l’intérieur de l’appareil

risque de causer une électrocution. Il est donc dangereux

de toucher quoi que ce soit à l’intérieur de l’appareil.

Ce symbole avertit l’utilisateur que d’importantes infor-

mations sont fournies sur le fonctionnement ou l’entretien

de cet appareil. Ces informations doivent être lues

attentivement pour éviter tout problème.

AVERTISSEMENT

AFIN DE PREVENIR TOUT RISQUE D’INCENDIE OU DE CHOC

ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À

L’HUMIDITÉ. N’UTILISEZ PAS LA PRISE AVEC TERRE DE

L’APPAREIL AVEC UNE RALLONGE OU UNE AUTRE PRISE, A

MOINS QUE LES TROIS BROCHES PUISSENT ÊTRE

COMPLETEMENT INSÉRÉES. N’OUVREZ PAS LE BOÎTIER. A

L’INTÉRIEUR SE TROUVENT DES COMPOSANTS À HAUTE TEN-

SION. TOUTE RÉPARATION DOIT ÊTRE FAITE PAR DU PERSON-

NEL AGRÉE NEC.

DOC avis de conformation

Cet appareil numérique de la classe B respecte toutes les exigences

du Règlement sur le Matériel Brouilleur du Canada.

3. Réglement sur les informations concernant les nuisances acoustiques GSGV:

Le niveau de pression sonore est inférieur à 70 dB (A) conformément

à la norme ISO 3744 ou ISO 7779.

• IBM est une marque déposées de International Business Machines

Corporation.

• Macintosh et PowerBook sont des marques déposées de Apple Com-

puter, Inc.

• Tous les autres marques et les noms de produits sont des marques

de fabrique ou des marques déposées de leurs compagnies

respectives.

E – iv

Important Safeguards

These safety instructions are to ensure the long life of your projector

and to prevent fire and shock. Please read them carefully and heed all

warnings.

Installation

1. For best results, use your projector in a darkened room.

2. Place the projector on a flat, level surface in a dry area away from

dust and moisture.

3. Do not place your projector in direct sunlight, near heaters or heat

radiating appliances.

4. Exposure to direct sunlight, smoke or steam can harm internal com-

ponents.

5. Handle your projector carefully. Dropping or jarring can damage in-

ternal components.

6. Do not place heavy objects on top of the projector.

7. If you wish to have the projector installed on the ceiling:

a. Do not attempt to install the projector yourself.

b. The projector must be installed by qualified technicians in order to ensure

proper operation and reduce the risk of bodily injury.

c. In addition, the ceiling must be strong enough to support the projector

and the installation must be in accordance with any local building codes.

d. Please consult your dealer for more information.

Power Supply

1. The projector is designed to operate on a power supply of 100-120

or 200-240 V 50/60 Hz AC. Ensure that your power supply fits this

requirement before attempting to use your projector.

2. Handle the power cable carefully and avoid excessive bending. A

damaged cord can cause electric shock or fire.

3. If the projector is not to be used for an extended period of time,

disconnect the plug from the power outlet.

Cleaning

1. Unplug the projector before cleaning.

2. Clean the cabinet periodically with a damp cloth. If heavily soiled,

use a mild detergent. Never use strong detergents or solvents such

as alcohol or thinner.

3. Use a blower or lens paper to clean the lens, and be careful not to

scratch or mar the lens.

CAUTION

Do not unplug the power cable from the wall outlet under any one

of the following circumstances. Doing so can cause damage to

the projector:

• While the Hour Glass icon appears.

• While the message "Please wait a moment." appears. This message

will be displayed after the projector is turned off.

• Immediately after the power cable is plugged into the wall outlet (the

POWER indicator has not changed to a steady orange glow).

• Immediately after the cooling fan stops working (The cooling fan con-

tinues to work for ONE minute after the projector is turned off with the

POWER button).

• While the POWER and the STATUS indicators are alternately flashing.

CAUTION

• Do not put the projector on its side when the lamp is turned on.

Doing so may cause damage to the projector.

• Before shipping this projector, remove the lens and attach the lens

hood cap.

The Lens Shift mechanism may encounter damage caused by improper

handling during transportation.

Lamp Replacement

• To replace the lamp, follow all instructions provided on page E-58.

• Be sure to replace the lamp when the message "The Lamp has

reached the end of its usable life. Please replace the lamp."

appears. If you continue to use the lamp after the lamp has reached

the end of its usable life, the lamp bulb may shatter, and pieces of

glass may be scattered in the lamp case. Do not touch them as the

pieces of glass may cause injury. If this happens, contact your NEC

dealer for lamp replacement.

• Allow a minimum of ONE minute to elapse after turning off the pro-

jector. Then disconnect the power cable and allow 60 minutes to

cool the projector before replacing the lamp.

Fire and Shock Precautions

1. Ensure that there is sufficient ventilation and that vents are unob-

structed to prevent the build-up of heat inside your projector. Allow

at least 3 inches (10 cm) of space between your projector and a

wall.

2. Prevent foreign objects such as paper clips and bits of paper from

falling into your projector. Do not attempt to retrieve any objects that

might fall into your projector. Do not insert any metal objects such as

a wire or screwdriver into your projector. If something should fall into

your projector, disconnect it immediately and have the object re-

moved by a qualified NEC service personnel.

3. Do not place any liquids on top of your projector.

• Do not look into the lens while the projector is on. Serious damage

to your eyes could result.

• Keep any items such as magnifying glass out of the light path of the

projector. The light being projected from the lens is extensive, there-

fore any kind of abnormal objects that can redirect light coming out

of the lens, can cause unpredictable outcome such as fire or injury

to the eyes.

• Do not cover the lens with the supplied lens cap or equivalent while

the projector is on. Doing so can lead to melting of the cap and

possibly burning your hands due to the heat emitted from the light

output.

4. When using a LAN cable:

For safety, do not connect to the connector for peripheral device

wiring that might have excessive Voltage.

E – v

Mesures de sécurité importantes

Ces instructions de sécurité garantissent la longévité de votre projecteur

et préviennent les risques d’incendie et de décharge électrique. Lisez-

les et respectez les conseils.

Installation

1.

Pour de meilleurs résultats‚ utilisez votre projecteur dans une pièce sombre.

2. Placez le projecteur sur une surface plane et à niveau, dans un

endroit sec à l’abri de la poussière et de l’humidité.

3. Ne placez pas votre projecteur en plein soleil‚ à côté d’appareils de

chauffage ou d’appareils dégageant de la chaleur.

4.L’exposition en plein soleil‚ la fumée ou la vapeur peuvent

endommager des composants internes.

5. Manipulez votre projecteur avec précaution. Une chute ou un choc

peuvent endommager des composants internes.

6. Ne placez pas d’objets lourds sur le projecteur.

7. Si vous voulez installer le projecteur au plafond:

a. N’essayez pas d’installer le projecteur vous-même.

b. Le projecteur doit être installé par un technicien qualifié pour garantir une

installation réussie et réduire le risque d’éventuelles blessures corporelles.

c. De plus le plafond doit être suffisamment solide pour supporter le

projecteur et l’installation doit être conforme aux réglementations locales

de construction.

d. Veuillez consulter votre revendeur pour de plus amples informations.

Alimentation

1. Ce projecteur est conçu pour fonctionner avec une alimentation

électrique de 100-120 ou 200-240 V 50/60 Hz. Assurez-vous que

votre alimentation correspond à ces critères avant d’essayer d’utiliser

votre projecteur.

2.Manipulez le câble d’alimentation avec précaution et évitez de

l’entortiller. Tout câble endommagé peut provoquer une décharge

électrique ou un incendie.

3.Si le projecteur ne doit pas être utilisé pendant longtemps,

débranchez la prise de la source d’alimentation.

Nettoyage

1. Débranchez le projecteur avant de procéder au nettoyage.

2. Nettoyez régulièrement le coffret avec un chiffon humide. Si celui-ci

est très sale, utilisez un détergent doux. N’utilisez jamais de

détergents puissants, de l’alcool ou d’autres solvants.

3. Utilisez un ventilateur ou un papier à objectif pour nettoyer l’objectif

et faîtes attention de ne pas rayer ou d’abîmer l’objectif.

Information importante

Ne pas débrancher le câble d’alimentation de la prise du secteur dans

les circonstances suivantes car cela risque d’endommager le projecteur:

* Lorsque l’icone Hour Glass (vitre d’heure) apparaît.

* Lorsque le message "Veuillez patientez un instant" apparaît. Ce mes-

sage sera affiché après que le projecteur soit éteint.

* Immédiatement après que le cordon d’alimentation électrique ait été

branché sur la prise du mur (l’indicateur POWER n’est pas encore

devenu orange).

* Immédiatement après que le ventilateur de refroidissement de soit arrêté

de fonctionner (le ventilateur de refroidissement continue à fonctionner

pendant UNE minute après l’extinction du projecteur grâce à

l’interrupteur POWER OFF).

* Lorsque les indicateurs POWER (alimentation électrique) et STATUS

(état) clignotent alternativement.

ATTETION

• Ne pas placer le projecteur sur le côté lorsque la lampe est allumée,

sinon le projecteur risque d’être endommagé.

• Avant d’expedier ce projecteur, veuillez démonter l’objectif et fixer le

bouchon d’objectif.

Le mécanisme de déplacement de l’objectif pourrait être endommagé

durant le transport à la suite d’une manipulation maladroite.

Remplacement de la lampe

• Effectuez le remplacement de la lampe en fonction des instructions

de la page E-60.

• Assurez-vous de remplacer la lampe lorsque le message “La lampe

a atteint sa durée de vie maximum, prière de la remplacer.”

apparaît. Si vous continuer à l ’utiliser au-delà de sa durée de vie,

celle-ci risque d’exploser et de répandre des fragments de verre à

l’intérieur du boîtier.

Ne les touchez pas car elles peuvent vous blesser. Dans ce cas,

contactez votre revendeur NEC afin de procéder au remplacement

de la lampe.

• Attendez au minimum UNE minute aprés avoir éteint la lampe avant

de la rallumer.

Une haute tension est immédiatement appliquée à la lampe quand

celle-ci est mise sous tension.

Par conséquent, éteindre, puis tout de suite rallumer peut réduire la

durée de vie de votre lampe et endommager votre projecteur.

Précautions contre les risques d’incendie et de

décharge électrique

1.Assurez-vous que la ventilation est suffisante et que les trous

d’aération ne sont pas obstrués afin d’éviter tout échauffement à

l’intérieur de votre projecteur. Laissez au-moins 3 pouces (10 cm)

d’espace entre le projecteur et le mur.

2. Evitez de faire tomber dans le projecteur des objets étrangers comme

des trombones ou des morceaux de papier. N’essayez pas de

récupérer tout objet tombé à l’intérieur de votre projecteur. N’insérez

pas d’objets métalliques comme du fil de fer ou un tournevis dans

votre projecteur. Si quelque chose est tombée à l’intérieur de votre

projecteur, débranchez-le immédiatement et faites retirer l’objet par

une personne qualifiée de la maintenance NEC.

3. Ne placez aucun liquide sur votre projecteur.

Avertissements

• Ne regardez pas à l’intérieur de l’objectif lorsque le projecteur est

en marche. Vous risquez de vous blesser gravement aux yeux.

• Maintenez tout ce qui s’apparente à une loupe en dehors du faisceau

lumineux du projecteur. La lumière projetée par l’objectif est très

puissante, de sorte que tout objet en opposition pourrait dévier le

faisceau provenant de l’objectif, ce qui pourrait avoir des

conséquences imprévues telles qu’un incendie ou une lésion

occulaire.

• Ne bouchez pas l’objectif avec son couvercle fourni lorsque le

projecteur est allumé. Faire cela pourrait faire fondre le couvercle et

peut-être brûler vos mains à cause de la châleur émise par le faisceau

lumineux.

• Ne tenez pas de pièces de l’objectif. Faire cela pourrait entraîner un

risque de blessure.

E – vi

TABLE OF CONTENTS

1. INTRODUCTION

What's in the Box? ....................................................................................... E-1

Getting to Know Your GT1150 Projector ...................................................... E-2

Attaching the lens hood cap to the lens hood

with the supplied string and rivet............................................... E-4

Carrying the Projector ........................................................................... E-4

Top Features ......................................................................................... E-5

Front Terminal Panel (Right) ................................................................. E-6

Front Terminal Panel (Left).................................................................... E-7

PC Card Viewer .................................................................................... E-7

Remote Control Features ..................................................................... E-8

Remote Control Precautions ....................................................... E-10

Remote Control Battery Installation............................................. E-10

Operating Range for Wireless Remote Control ........................... E-10

Using the Remote Control in Wired Operation ............................ E-11

2. INSTALLATION

Setting Up Your GT1150 Projector ............................................................. E-12

Screen Size and Projection Distance......................................................... E-12

Lens Shift Adjustable Range...................................................................... E-13

Optional Lens Installation........................................................................... E-14

Setting up for Double Stacking in Link Mode ............................................. E-16

Projector Orientation .................................................................................. E-17

3. Basic Operation

Connecting the Power Cable and Turn on the Projector ............................ E-19

About Startup Screen ................................................................................ E-20

Set up the projector.................................................................................... E-21

Other adjustments...................................................................................... E-22

4. CONNECTIONS

When used in standalone operation .......................................................... E-23

Connecting Your VCR Or Laser Disc Player ....................................... E-23

Connecting Your DVD Player with Component Output........................ E-24

Connecting Your PC Or Macintosh Compute...................................... E-25

Connecting an External Monitor ......................................................... E-26

Connecting a PC with DVI output ....................................................... E-26

Connecting to a Single Workstation .................................................... E-27

Ferrite Core Installation ............................................................... E-27

When Used with One Switcher (ISS-6020/ISS-6020G) ............................. E-28

When Used with Two or More Switchers (100 Inputs) ............................... E-29

How to make connections.................................................................. E-29

Set the DIP switch (S8601) of the Switcher as follows ....................... E-30

REMOTE 1 Connector........................................................................ E-31

Operating Multiple Projector with Remote Control ..................................... E-33

Using the PC CONTROL connectors......................................................... E-34

5. OPERATION

General Controls ........................................................................................ E-35

Using the Menus ........................................................................................ E-35

Using the Magnifying Glass Icon ............................................................... E-35

Customizing Basic/Custom Menu .............................................................. E-36

List of Direct Button Combinations............................................................. E-37

Menu Tree .................................................................................................. E-38

Menu Elements .......................................................................................... E-39

Menu Descriptions & Functions ................................................................. E-40

Source Select............................................................................................. E-40

Entry List .................................................................................................... E-40

Picture ........................................................................................................ E-41

Brightness/Contrast/Color/Hue/Sharpness

Volume ....................................................................................................... E-41

Image Options............................................................................................ E-42

Keystone ............................................................................................. E-42

Color Temperature .............................................................................. E-42

Lamp Mode......................................................................................... E-42

Gamma Correction ............................................................................. E-42

Aspect Ratio ....................................................................................... E-42

Noise Reduction ................................................................................. E-42

Color Matrix ........................................................................................ E-43

White Balance..................................................................................... E-43

Switcher Gain ..................................................................................... E-43

Position/Clock ..................................................................................... E-43

Resolution........................................................................................... E-43

Video Filter.......................................................................................... E-44

Overscan ............................................................................................ E-44

Clamp Timing ...................................................................................... E-44

Y/C Delay............................................................................................ E-44

YTR Adjustmen................................................................................... E-44

CTR Adjustment ................................................................................. E-44

HD Delay ............................................................................................ E-44

Factory Default ................................................................................... E-44

Projector Options ....................................................................................... E-44

Timer (On/Off Timer/Sleep Timer) ...................................................... E-44

Menu................................................................................................... E-45

Menu Mode......................................................................................... E-45

Language............................................................................................ E-45

Menu Display Time ............................................................................. E-45

Display Select ..................................................................................... E-46

Date Format........................................................................................ E-46

Date, Time Preset ............................................................................... E-46

Projector Pointer ................................................................................. E-46

Direct Button (Volume Bar and Keystone Bar).................................... E-46

Setup .................................................................................................. E-47

Orientation .......................................................................................... E-47

Background......................................................................................... E-47

PC Card Viewer Options ..................................................................... E-47

Capture Options.................................................................................. E-47

Signal Select....................................................................................... E-47

Signal Select(RGB connector)........................................................... E-48

Auto Adjust (RGB only)....................................................................... E-48

Auto Start............................................................................................ E-48

Power Management ............................................................................ E-48

Power Off Confirmation ...................................................................... E-48

Keystone Save .................................................................................... E-48

Fan High Speed Mode ........................................................................ E-48

Built-in Speaker .................................................................................. E-48

Clear Lamp Hour Meter ...................................................................... E-48

Clear Filter Usage............................................................................... E-48

Remote Sensor................................................................................... E-49

S-Video Mode Select .......................................................................... E-49

Communication Speed ....................................................................... E-49

Projector ID......................................................................................... E-49

Default Source Select ......................................................................... E-49

Link Mode ........................................................................................... E-49

Switcher Control ................................................................................. E-49

Tools........................................................................................................... E-50

Capture ............................................................................................... E-50

PC Card Files ..................................................................................... E-50

Changing Background Logo ............................................................... E-50

Help............................................................................................................ E-51

Contents ............................................................................................. E-51

Information.......................................................................................... E-51

Test Pattern ................................................................................................ E-51

Using the PC Card Viewer Function .......................................................... E-52

Features.............................................................................................. E-52

Inserting and Ejecting a PC Card ....................................................... E-52

Installing the PC Card Viewer Software .............................................. E-53

Starting Up the PC Card Viewer Software on your PC

(PC Card Viewer Utility 10) ................................................................. E-53

Operating the PC Card Viewer Function from the Projector

(playback) ........................................................................................... E-54

Capturing Images Displayed on the Projector .................................... E-56

Viewing Digital Images ....................................................................... E-56

Uninstalling the PC Card Viewer Software ......................................... E-57

6. MAINTENANCE

Replacing the Lamp ................................................................................... E-58

Cleaning or Replacing the Filter................................................................. E-59

Remplacement de la lampe ....................................................................... E-60

Nettoyage ou remplacement du filtre ......................................................... E-61

7. TROUBLESHOOTING

Power / Status Light Messages.................................................................. E-62

Lamp Light Messages ................................................................................ E-62

Common Problems & Solutions ................................................................. E-62

8. SPECIFICATIONS

Optical/Electrical ........................................................................................ E-64

Mechanical ................................................................................................. E-65

Cabinet Dimensions ................................................................................... E-66

Optional Accessories ................................................................................. E-66

D-Sub Pin Assignments ............................................................................. E-67

List of Menu Items Available in Link Mode ................................................. E-68

Timing Chart .............................................................................................. E-69

PC Control Codes ...................................................................................... E-70

Cable Connection ...................................................................................... E-70

Gravity Stack .............................................................................................. E-70

E – 1

What's in the Box?

Make sure your box contains everything listed. If any pieces are missing, contact your dealer.

Please save the original box and packing materials if you ever need to ship your GT1150 Projector.

1. INTRODUCTION

R

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

SE

LE

C

T

LE

N

S S

H

IF

T

L

E

F

T

Z

O

OM

F

O

C

U

S

U

P

D

O

W

N

R

IGH

T

A

U

T

O

A

D

J

U

S

T

L

A

M

P

S

T

A

T

U

S

P

O

W

E

R

O

N

/S

T

A

N

D

B

Y

S

O

U

R

C

E

NOTE: Lenses are optional. Order lenses from your NEC dealer.

Lens hood cap

Remote control and batteries (AAA x 2)

String and rivet

RGB signal cable

(15-Pin Mini D-Sub To 15-Pin Mini D-Sub connector)

CD-ROM

Power cable for Europe (AC 220-240V)

Power cable for North America (AC 120V) Power cable for Japan (AC 100V)

GT1150 Projector

Remote cable

User’s manuals

(Japanese and English/German)

Ferrite clamp core for a commercially

available BNC cable

(For RGB 2 connector. See page E-27

for installation instructions.)

E – 2

R

E

M

O

T

E

1

P

C

O

N

T

R

O

L

REM

OTE

2

A

C

IN

S

C

,

T

R

IG

G

E

R

O

U

TO

U

T

IN

I

N

D

V

IL

/

M

O

N

O

L

/

M

O

N

O

R

G

B

1

R

G

B

2

V

I

D

E

O

1

V

I

D

E

O

2

S

-

V

I

D

E

O

A

U

D

I

O

U

T

R

/

C

r

G

/

Y

B

/

C

b

V

H

/H

V

M

O

N

IT

O

R

O

U

T

R

L

/M

O

N

O

R

L

/

M

O

N

O

R

L

/

M

O

N

O

R

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

S

E

L

E

C

T

L

E

N

S

H

IF

T

L

E

F

T

Z

O

M

F

O

C

U

S

U

P

D

O

W

N

R

IG

H

T

A

U

T

O

A

D

J

U

S

T

L

A

M

P

S

T

A

T

U

S

P

O

W

E

R

O

N

/S

T

A

N

D

B

Y

S

O

U

R

C

E

Getting to Know Your GT1150 Projector

Lens hood

Remote sensor

Terminal panel (Left)

AC INPUT

Connect the supplied power

cable’s three-pin plug here.

Lens (optional)

Lens hood cap

Controls

PC Card slot

Open the cover to access

the PC card slot.

Remote sensor

Ventilation (outlet)

Built-in Security Slot ( )*

Foot (four)

Rotate to fine-adjust the height of each foot.

Terminal panel (Right)

*NOTE: Slot for Kensington MicroSaver Security System

This security slot supports the MicroSaver

®

Security System.

MicroSaver

®

is a registered trademark of Kensington Microware Inc. The logo

is trademarked and owned by Kensington Microware Inc.

E – 3

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

S

E

L

E

C

T

L

E

N

S

H

IF

T

L

E

F

T

Z

O

M

F

O

C

U

S

U

P

D

O

W

N

R

IG

H

T

A

U

T

O

A

D

J

U

S

T

L

A

M

P

S

T

A

T

U

S

P

O

W

E

R

O

N

/S

T

A

N

D

B

Y

S

O

U

R

C

E

Depression for foot (4 locations)

Speaker (Left)

Remote sensor

Speaker (Right)

Remote sensor

Carrying handle

Lamp cover

DVI

L/MONO

RGB 1

RGB 2

VIDEO 1

VIDEO 2

S

-

VIDEO

AUDIO OUT

R/Cr

G/Y

B/Cb

V

H/HV

MONITOR OUT

R

L/MONO R

L/MONO

R

L/MONO

R

E

M

O

T

E

1

P

C

O

N

T

R

O

L

REMOTE

2

A

C

IN

S

C

, T

R

IG

G

E

R

O

U

T

O

U

T

IN IN

Air filter

Ventilation (inlet)

E – 4

Attaching the lens hood cap to the lens hood with the supplied string and rivet

1. Thread the string through the hole on the lens hood cap.

Lens hood cap

String

2. Use the rivet to attach the string to the bottom of the projector.

D

V

I

L

/

M

O

N

O

L

/

M

O

N

O

R

G

B

1

R

G

B

2

V

I

D

E

O

1

V

I

D

E

O

2

S

-

V

I

D

E

O

A

U

D

I

O

U

T

R

/

C

r

G

/

Y

B

/

C

b

V

H

/

H

V

M

O

N

I

T

O

R

O

U

T

R

L

/

M

O

N

O

R

L

/

M

O

N

O

R

L

/

M

O

N

O

R

G

B

1

S

-

V

I

D

E

O

A

U

D

I

O

U

T

G

/

Y

B

/

C

b

V

H

/

H

V

L

/

M

O

N

O

R

L

/

M

O

N

O

R

L

/

M

O

N

O

R

Rivet

Carrying the Projector

Always carry your projector by the handle.

Ensure that the power cable and any other cables connecting to video sources

are disconnected before moving the projector.

When moving the projector or when it is not in use, cover the lens with the

lens hood cap.

CAUTION:

Do not put the projector on its side when the lamp is on.

Doing so may cause damage to the projector.

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

SELECT

LENS SHIFT

LEFT

ZOOMFOCUS

UP

DOWN

RIGHT

AUTO

ADJUST

LAMP

STATUS POWER

ON/STAND BY

SOURCE

E – 5

E

N

T

E

R

C

A

N

C

E

L

LENS SHIFT

LEFT

ZOOM

FOCUS

UP

DOWN

RIGHT

A

U

T

O

A

D

JU

S

T

L

A

M

P

S

T

A

T

U

S

P

O

W

ER

O

N

/S

T

A

N

D

B

Y

S

O

U

R

C

E

SELECT

M

E

N

U

10

9

8

7

6

5

4

2

3

11

12

13

1

1. Power Button (ON / STAND BY)

Use this button to turn the power on and off when the power is sup-

plied and the projector is in standby mode.

NOTE: To turn off the projector, press and hold this button for a minimum of

two seconds.

2. Auto Adjust Button (RGB only)

Use this button to adjust Position-H/V and Pixel Clock/Phase for an

optimal picture. Some signals may not be displayed correctly or take

time to switch between sources.

3. Source Button

Use this button to select a video source such as a PC, VCR, DVD

player or PC Card Viewer (PC card).

Each time this button is pressed, the input source will change as fol-

lows:

→ RGB1 → RGB2 → Video1 → Video2 → S-Video → DVI digital →

DVI analog → PC Card Viewer

If no input signal is present, the input will be skipped.

4. Menu Button

Displays the menu.

5. Select ▲▼

䊴

䊳

/ Volume (+) (-) Buttons

▲▼: Use these buttons to select the menu of the item you wish to

adjust.

When no menus appear, these buttons work as a volume con-

trol.

䊴

䊳

: Use these buttons to change the level of a selected menu item.

A press of the

䊳

button executes the selection.

When the menus or the Viewer tool bar is not displayed, these

䊴

䊳

buttons can be used to select a slide, or to move the cur-

sor in Folder List or Slide List.

When the pointer is displayed, these ▲▼

䊴

䊳

buttons move

the pointer.

6. Enter Button

Executes your menu selection and activates items selected from the

menu.

Top Features

7. Cancel Button

Press this button to exit “Menus”. Press this button to return the adjust-

ments to the last condition while you are in the adjustment or setting

menu.

8 Lens Shift Button

Adjust the lens offset by shifting the projected image position horizon-

tally and / or vertically.

9 Zoom Button

Zoom the lens in and out.

10 Focus Button

Adjust the lens focus.

11. Lamp Remaining Indicator

Indicates the lamp remaining amount. See the Lamp Light Messages

on page E-62 for more details.

12. Status Indicator

When this is lit red (orange in Eco mode) continually, it‘s warning you

that the projection lamp has reached the end of its usable life (1500

hours in High-Bright mode and up to 2000 hours in Eco mode). After

this light appears, it is advisable to replace the projection lamp as soon

as possible. (See page E-58 or 60). In addition the message "The lamp

has reached the end of its usable life. Please replace the lamp." ap-

pears continually until the lamp is replaced.

If the projector is in Eco mode or something out of the ordinary takes

place, this indicator is lit or blinks. For example, If this light blinks red

rapidly, it indicates that the lamp cover is not attached properly or the

projector is overheated.

See the Power / Status Light Messages on page E-62 for more details.

13. Power Indicator ( )

When this indicator is green, the projector is on; when the indicator is

orange, it is in standby mode.

E – 6

DVI

L/MONO

RGB 2

RGB 1

VIDEO 1

VIDEO 2

S

-

VIDEO

AUDIO OUT

R/Cr

G/Y

B/Cb

V

H/HV

MONITOR OUT

R

L/MONO

R

L/MONO

R

L/MONO

R

1

5

8

9

11

10

12

13

7

6

3

4

2

1. DVI Connector

This connector can be used to accept digital or analog signal output

from a computer with a DVI connector.

2. DVI Audio Input Jacks (RCA)

These are the left channel and the right audio inputs for stereo sound

coming from the equipment connected to a computer with DVI output.

L/MONO

This is your left channel audio input for stereo sound from the equip-

ment connected to a computer with DVI output.

The L/MONO jack also serves as your monaural audio input.

R

This is your right channel audio input for stereo sound from the equip-

ment connected to a computer with DVI output.

3. RGB 2 Connector (Mini D-Sub 15 pin)

Connect your PC, Macintosh, DVD player with Y/Cb/Cr outputs or other

RGB equipment. The optional Component V. Cable is required for Y/

Cb/ Cr input connection.

NOTE:

The RGB2 connector does not support the Switcher Control mode.

4. RGB 2 Audio Input Jacks (RCA)

L/MONO

This is your left channel audio input for stereo sound coming from the

RGB Input 2 source.

This also serves as your monaural audio input.

R

This is your right channel audio input for stereo sound from the RGB

Input 2 source.

Front Terminal Panel (Right)

5. MONITOR OUT Connector (Mini D-Sub 15

pin)

You can use this connector to loop your computer

image an external monitor from either the RGB 1,

RGB 2 or DVI analog input source.

6. RGB 1 Input Connectors (BNC)

Connect R,G,B,H (Horizontal sync) and V (Vertical

sync) outputs of external equipment such as the NEC

ISS-6020Switcher.

If using a component with a combined sync (SYNC)

output, connect it to the H/V terminal. When using

luminance and color-difference signals of HDTV and

DVD, connect Pr/Cr to the R,Y to the G and Pb/Cb

to the B input of the projector.

7. RGB 1 Audio Input Jacks (RCA)

L/MONO

This is your left channel audio input for stereo sound

coming from the RGB Input 1 source.

This also serves as your monaural audio input.

R

This is your right channel audio input for stereo sound

from the RGB Input 1 source.

8. VIDEO 1 Input Connector (BNC)

Connect a VCR, DVD player, laser disc player, or

document camera here to project video.

9. VIDEO 2 Input Connector (RCA)

Connect a VCR, DVD player, laser disc player, or

document camera here to project video.

10. VIDEO Audio Input Jacks (RCA)

L/MONO

This is your left channel audio input for stereo sound coming from the

VIDEO 1 or VIDEO 2 source.

This also serves as your monaural audio input.

R

This is your right channel audio input for stereo sound from the VIDEO

1 or VIDEO 2 source.

11. S-VIDEO Input Connector (Mini DIN 4 pin)

Here is where you connect the S-Video input from an external source

such as a VCR or laser disc player.

NOTE: S-Video provides more vivid color and higher resolution than the tradi-

tional composite video format.

12. S-VIDEO Audio Input Jacks (RCA)

L/MONO

This is your left channel audio input for stereo sound coming from the

S-VIDEO source.

This also serves as your monaural audio input.

R

This is your right channel audio input for stereo sound from the S-

VIDEO source.

13. AUDIO OUT Jacks (RCA)

You can use this connector to output sound from the currently selected

input source (RGB 1, RGB 2, VIDEO 1, VIDEO 2, S-VIDEO or DVI

[digital/analog] ). Output sound level can be adjusted in accordance

with the sound level of the internal speaker.

E – 7

REMOTE 1

PC CONTROL

R

EM

O

TE

2

AC IN

SC, TRIGGER

OUT OUT

IN

3

5

4

1

2

6

9

8

7

LENS SHIFT

LEFT

ZOOM

FOCUS

UP

DOWN

RIG

1. PC CONTROL Connectors (Mini D-Sub 9 pin)

For system expansion such as PC-Control.

IN: connect to the external equipment such as PC.

OUT: for daisy-chaining multiple projectors and operating them with

the same external equipment. To do so, connect to a second

projector’ s IN terminal to relay the input at the IN terminal of the

first projector until all the projectors are connected.

2. REMOTE 1 Connector (Mini D-Sub 15 pin)

This terminal allows external control of the projector from either the

Switcher or from an external control. When the Switcher is used, con-

nect to the REMOTE 1 terminal on the back of the Switcher.

NOTE: This projector is compatible with the ISS-6020 Switcher.

3. REMOTE 2 Mini Jacks

IN: wired remote control input.

OUT: for daisy-chaining multiple projectors and operating them with

the same remote control. To do so, connect to a second projec-

tor’ s IN terminal to relay the input at the IN terminal of the first

projector until all the projectors are connected.

4. SC. TRIGGER Mini Jack

Screen Trigger- When the GT1150 is powered ON the screen trigger

output sends a low voltage trigger to the screen controller and the

screen will go down.

Front Terminal Panel (Left)

When the GT1150 is powered OFF the screen trigger stops sending a

low voltage trigger to the screen controller and the screen will go up.

NOTE: Screen Controllers are supplied and supported by screen manufactures.

This option is not included with the GT1150 projector.

NOTE: Do not use this jack for anything other than intended use. Connecting

the wired remote control to the SC. TRIGGER Mini Jack causes damage to the

remote control.

5. Slot for LAN Board (Optional)

Use this connector to control the projector on a LAN. The optional LAN

kit is required when this connector is used. See the instructions in-

cluded with the optional LAN kit.

6. AC IN

Connect the supplied power cable’s three-pin plug here.

Three types of power cable are supplied with this LCD projector: three-

pin type for U. S. A. and Canada. Two-pin type for Germany and Japan.

7. PC Card Slot

Insert a PC card here.

8. PC Card Eject Button

Press to eject a PC card.

9. PC Card Access Indicator

Lights while accessing a PC card.

PC Card Viewer

Push down to open the PC

Card Slot cover.

Tip (12V)

Ring (0V)

Sleave (ground. 0V)

Stereo mini cable

(not supplied)

E – 8

OFF

+

-

PICTURE

ADJUST

ABC DEF

GHI

JKL MNO PQR

STU

,.

UNDO CANCEL

TEST

PICTURE

KEYSTONE AMPLITUDE ENTRYLIST

SOUND OSD

MUTE

MAGNIFY

HELPINFO.

POSITION AUTOPIXEL

VWX YZ?

WHITE BAL.

IMAGE

ON

POWER

MENU

ENTER

123

456

7

0

8

9

ADDRESS

PROJECTOR

R G B

LENS

SHUTTER

BS

+

-

+

-

FOCUS ZOOM

CTL

LENS

2

5

6

7

9

10

12

13

17

20

21

22

24

26

2

5

2

3

1

9

1

8

1

6

1

5

1

4

11

8

4

3

1

Remote Control Features

1. POWER ON Button

Press this button to turn on the projector when the power is supplied

and the projector is in standby mode.

2. POWER OFF Button

Press and hold this button for a minimum of two seconds to turn off the

projector.

3. MENU Button

Press to display the main menu.

While pressing and holding CTL, press this button to display the Re-

mote Control ID dialog box to specify the remote control ID. See page

E-33.

4. ENTER Button

Executes the menu selection and activates items selected from the

menu. When the slider or dialog box is displayed:

Pressing this button confirms adjustments/setting and returns to the

previous menu display.

5. Select (Up/Down/Left/Right) Button

▲▼: Use these buttons to select the menu of the item you wish to

adjust.

When no menus appear, these buttons work as a volume con-

trol.

䊴

䊳

: Use these buttons to change the level of a selected menu item.

A press of the

䊳

button executes the selection.

When the menus or the Viewer tool bar is not displayed, these

䊴

䊳

buttons can be used to select a slide, or to move the cursor in

Folder List or Slide List.

When the pointer is displayed, these ▲▼

䊴

䊳

buttons move the pointer.

See page E-35 for displaying the pointer.

Pressing and holding CTL, then pressing

䊴

button works as a Back

Space key in the entry screen.

Pressing and holding CTL, then pressing this button moves the menu,

slider, toolbar or dialog box.

6. ADJUST WHITE BAL Button

Press to display the color adjustment screen. Pressing this button se-

quentially selects "Color Temperature" → "White Balance" → "Switcher

Gain".

7. ADJUST PICTURE Button

Press to display the Picture screen.

8. IMAGE/PROJECTOR Button

Press to display the Image Options screen.

Pressing this button sequentially selects "Gamma Correction" → "As-

pect Ratio" → "Noise Reduction" → "Color Matrix" → "Resolution" →

"Video Filter" → "Overscan" → "Clamp Timing” → "Y/C Delay" → "YTR

Adjustment" → "CTR Adjustment" → "HD Delay".

While pressing and holding CTL, pressing this button rotates "On/Off

Timer" → "Sleep Timer" → "Menu" → "Setup" → "Link Mode" →

"Switcher Control" → "LAN mode" (optional).

9. Source / Alphanumeric Buttons

Press to select input or to name a signal.

1 .................. Selects RGB 1 input.

2 .................. Selects RGB 2 input.

3 .................. Selects VIDEO 1 input.

4 .................. Selects VIDEO 2 input.

5 .................. Selects S-VIDEO 1 input.

6 .................. Selects DVI digital input.

7 .................. Selects DVI analog input.

8 .................. Selects PC Card Viewer.

9 .................. Selects RGB1 (VIDEO) input

0 .................. Selects RGB2 (S-VIDEO) input

E – 9

OFF

+

-

PICTURE

ADJUST

ABC DEF

G

JKL

MN

S

TU

WHITE BAL.

IMAGE

ON

POWER

MENU

ENTER

12

4

A

D

R

E

S

P

R

O

J

E

BS

27

28

10. UNDO

Press to return the adjustments and settings to the previous condition.

While pressing and holding CTL, pressing this button clears the entire

menus or adjustment/setting screen. At this time the adjustments/set-

tings are stored in memory except the items on the setting screen with

"OK" and "Cancel" buttons such as the Menu and the Setup screen.

11. CANCEL

Press to exit the menu.

Press this button with CTL to return to the previous menu without clos-

ing adjustment/setting screen while the menus appear. This feature

allows you to adjust or set several items concurrently.

12. INFO

Displays the Information screen.

13. TEST

Press to display the test pattern. Pressing this button sequentially se-

lects nine test patterns.

14. HELP

Provides online help.

15. PIXEL

Displays the Position/Clock screen to adjust the clock and phase.

16. AUTO (RGB only)

Press to adjust Position-H/V and Pixel Clock/Phase for an optimal pic-

ture.

17. POSITION

Press to display the Position/Clock screen.

While pressing and holding CTL, pressing this button displays the Lens

Shift adjustment screen.

18. MUTE SOUND

Turns off the sound for a short period of time. Press again to restore

the sound.

19. MUTE OSD

Press to turn off the on-screen display. Press again to restore the on-

screen display.

NOTE: You can also turn off the on-screen display forcefully by pressing and

holding CTL and then pressing MUTE OSD (Forced On-Screen Mute Mode) ;

doing this again restores it. In this case any adjustment will still change the

projector's memory settings. This mode is available even when input is switched

to another or the power is turned off the main power.

20. MUTE PICTURE

Press to turn off the picture for a short period of time. Press again to

restore the picture.

21. KEYSTONE (R)

Press to display the Keystone Correction screen.

When the test pattern is displayed, while pressing and holding CTL,

pressing this button displays a red test pattern.

22. AMPLITUDE (G)

Service personnel only.

When the test pattern is displayed, while pressing and holding CTL,

pressing this button displays a green test pattern.

23. ENTRY LIST (B)

Press to display the Entry List screen.

When the test pattern is displayed, while pressing and holding CTL,

pressing this button displays a blue test pattern.

24. FOCUS (+/–)

While pressing and holding CTL, pressing this button allows you to

adjust the lens focus.

25. MAGNIFY/ZOOM (+/–)

Magnify the size of a target portion.

While pressing and holding CTL, pressing this button allows you to

zoom the lens in and out.

26. CTL

Used in conjunction with other buttons, similar to a shift key on a com-

puter.

27. Remote Jack

Connect your remote control cable here for wired operation.

28. Infrared Transmitter

Direct the remote control toward the remote sensor on the projector

cabinet.

E – 10

7m

30˚

Remote Control Precautions

• The remote control system may not function when direct sunlight or

strong illumination strikes the remote control sensor of the main unit,

or when there is an obstacle in the path.

• When remote control buttons are pressed and held, projector’s func-

tion keys may not operate.

• Do not subject to strong shock.

• Do not allow water or other liquid to splash on the remote control. If

the remote control gets wet, wipe it dry immediately.

• Avoid exposure to heat and steam.

• Remove the batteries from the remote control when the remote con-

trol is not going to be used for a long period.

Remote Control Battery Installation

Installing the Remote Control Batteries

When it comes time to replace the batteries, two "AAA" type will be

required.

1. Press and open the cover.

2. Align and insert the batteries according to the (+) and (-) indica-

tions inside the case.

3. Replace the cover.

Operating Range for Wireless Remote Control

The infrared signal operates by line-of-sight up to a distance of ap-

proximately 7m (20 feet) and a 60 degree angle of the remote sensor.

The projector will not function if there are objects between the remote

sensor and the remote control or if strong light falls on the remote

sensor. Weak batteries will also prevent the projector from operating

properly.

Remote sensors on the projector cabinet

Side View

7m

30˚

Remote control

NOTE: You cannot operate the projector using the remote control if:

• The remote control ID is not set to [None].

• The remote ID is not the same as the projector ID.

See page E-33 for setting remote ID and page E-49 for setting projector ID.

E – 11

Using the Remote Control in Wired Operation

Connect one end of the supplied remote cable to the REMOTE 2 IN

mini jack and the other end to the remote jack on the remote control.

Terminal panel (Left)

REMOTE 1

PC CONTROL

REMOTE

2

AC IN

SC, TRIGGER

OUT OUT

IN IN

O

F

+

-

P

IC

T

UR

E

A

D

JU

ST

ABC DEF

GHI

JKL MNO

PQR

STU

,.

UNDO

CANCEL

ES

T

ST

D

HELPINFO.

AUTO

P

IXEL

VWX YZ?

W

H

ITE

BA

L.

IM

AG

E

O

N

P

O

W

E

R

MENU

ENTER

123

456

7

0

8

9

AD

DR

ES

S

PR

OJEC

TO

R

BS

Remote cable (supplied)

E – 12

2. INSTALLATION

This section describes how to set up your GT1150 projector and how to connect video and audio sources.

Setting Up Your GT1150 Projector

Your GT1150 Projector is simple to set up and use. But before you get started, you must first:

List of Screen Sizes

Screen size Width (H) Height (V)

m feet m feet

40" 0.8 2.7 0.6 2.0

60" 1.2 4.0 0.9 3.0

80" 1.6 5.3 1.2 4.0

100" 2.0 6.7 1.5 5.0

120" 2.4 8.0 1.8 6.0

150" 3.0 10.0 2.3 7.5

200" 4.1 13.3 3.0 10.0

250" 5.1 16.7 3.8 12.5

300" 6.1 20.0 4.6 15.0

400" 8.1 26.7 6.1 20.0

500" 10.2 33.3 7.6 25.0

Formulas: Screen width H (m)= Screen Diagonal (4:3) x 4/5 x 0.0254

Screen height V (m)= Screen Diagonal (4:3) x 3/5 x 0.0254

Screen width H (feet)= Screen size x 4/5

Screen height V (feet)= Screen size x 3/5

Width

Height

Screen size (Diagonal)

Lens Model GT10RL GT13ZL GT19ZL GT34ZL

Magnification

1.0 1.3 – 1.6 1.8 – 2.4 3.4 – 5.2

40" 0.8 (m) 2.7 (feet) 1.1-1.3 (m) 3.5-4.3 (feet) 1.5-2.0 (m) 4.8-6.4 (feet) – –

60" 1.2 (m) 4.0 (feet) 1.6-2.0 (m) 5.2-6.4 (feet) 2.2-2.9 (m) 7.2-9.6 (feet) – –

67" 1.3 (m) 4.4 (feet) 1.7-2.1 (m) 5.7-7.0 (feet) 2.5-3.2 (m) 8.1-10.6 (feet) – –

72" 1.4 (m) 4.7 (feet) 1.9-2.3 (m) 6.1-7.5 (feet) 2.6-3.5 (m) 8.7-11.4 (feet) – –

80" 1.6 (m) 5.3 (feet) 2.1-2.6 (m) 6.9-8.5 (feet) 2.9-3.9 (m) 9.6-12.8 (feet) 5.5-8.5 (m) 18.1-27.7 (feet)

84" 1.7 (m) 5.5 (feet) 2.2-2.7 (m) 7.1-8.8 (feet) 3.1-4.1 (m) 10.2-13.3 (feet) 5.9-9.0 (m) 19.3-29.3 (feet)

90" 1.8 (m) 6.0 (feet) 2.3-2.9 (m) 7.7-9.5 (feet) 3.3-4.3 (m) 10.9-14.3 (feet) 6.3-9.6 (m) 20.7-31.4 (feet)

100" 2.0 (m) 6.7 (feet) 2.6-3.3 (m) 8.7-10.7 (feet) 3.7-4.9 (m) 12.0-16.0 (feet) 6.9-10.6 (m) 22.7-34.6 (feet)

120" 2.4 (m) 8.0 (feet) 3.2-3.9 (m) 10.4-12.8 (feet) 4.4-5.9 (m) 14.4-19.2 (feet) 8.3-12.7 (m) 27.2-41.6 (feet)

150" 3.0 (m) 10.0 (feet) 4.0-4.9 (m) 13.0-16.0 (feet) 5.5-7.3 (m) 18.0-24.0 (feet) 10.4-15.8 (m) 34.0-52.0 (feet)

180 3.7 (m) 12.1 (feet) 4.7-5.8 (m) 15.5-19.1 (feet) 6.7-8.8 (m) 22.1-28.8 (feet) 12.8-19.3 (m) 42.1-63.4 (feet)

200" 4.1 (m) 13.3 (feet) 5.3-6.5 (m) 17.3-21.3 (feet) 7.3-9.8 (m) 24.0-32.0 (feet) 13.8-21.1 (m) 45.3-69.3 (feet)

210" 4.3 (m) 14.2 (feet) 5.5-6.8 (m) 18.1-22.4 (feet) 7.9-10.3 (m) 25.8-33.7 (feet) 15.0-22.6 (m) 49.2-74.0 (feet)

240" 4.9 (m) 16.2 (feet) 6.3-7.8 (m) 20.8-25.6 (feet) 9.0-11.7 (m) 29.6-38.5 (feet) 17.1-25.8 (m) 56.3-84.7 (feet)

250" 5.1 (m) 16.7 (feet) 6.6-8.1 (m) 21.7-26.6 (feet) 9.1-12.2 (m) 30.0-40.0 (feet) 17.3-26.4 (m) 56.6-86.6 (feet)

270" 5.6 (m) 18.3 (feet) 7.1-8.8 (m) 23.4-28.8 (feet) 10.1-13.2 (m) 33.3-43.3 (feet) 19.3-29.1 (m) 63.4-95.3 (feet)

300" 6.1 (m) 20.0 (feet) 7.9-9.8 (m) 26.0-32.0 (feet) 11.0-14.6 (m) 36.0-48.0 (feet) 20.7-31.7 (m) 68.0-103.9 (feet)

400" – – – – – – 27.6-42.3 (m) 90.6-138.6 (feet)

500" – – – – – – 34.5-52.8 (m) 113.3-173.2 (feet)

Screen Size (Diagonal)

Table of Throw Distances and Screen Sizes for Optional Lenses

GT13ZL (H⳯1.3) – (H⳯1.6)

GT19ZL (H⳯1.8) – (H⳯2.4)

GT34ZL (H⳯3.4) – (H⳯5.2)

GT10RL (H⳯1.0)

Throw distance

For screen sizes between 40” and 500” not indicated on the above table, use formulas below.

Projection Distance = Screen Width (H) x Lens Magnification

Throw distance for GT10RL lens (m/feet) =H x 1.0 (For H between 0.8 m/2.7feet and 6.1 m/20.0 feet)

Throw distance for GT13ZL lens (m/feet) =H x 1.3 through H x 1.6 (For H between 1.1 m/3.5 feet and 9.8 m/32.0 feet)

Throw distance for GT19ZL lens (m/feet) =H x 1.8 through H x 2.4 (For H between 1.5 m/4.8 feet and 14.6 m/48.0 feet)

Throw distance for GT34ZL lens (m/feet) =H x 3.4 through H x 5.2 (For H between 5.5 m/18.1 feet and 52.8 m/173.2 feet)

NOTE: Distances may vary +/-5%.

1. Determine the image size

2. Set up a screen or select a non-glossy white wall onto which you

can project your image.

3. Install the optional lens to the projector.

4. Connect the supplied power cable.

5. Set up the projector.

6. Connect a PC, VCR, DVD player, or other equipment.

7. Make settings or adjustments on the projector.

Screen Size and Projection Distance

Applicable lens and throw distance/ List of screen sizes

La page charge ...

NEC GT1150 Series Manuel utilisateur

Ce manuel convient également à

NEC GT1150 Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents