PAC260/261 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8” (1.6cm). Do
not install drywall anchors into the seam between drywall
pieces.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the PAC260/261 up to (and
including) the media player does not exceed 30 lbs (13.6 kg).
Use with products heavier than the maximum weight
indicated may result in collapse of the mount and its
accessories causing possible injury.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
Installation Instructions PAC260/261
3
DIMENSIONS
136.5
5.38
PAC260D
PAC260P
100
3.94
1.94
FITS 1-1/2" PIPES
61
2.40
PAC260/261 Installation Instructions
4
DIMENSIONS (CONTINUED)
PAC260W
182
7.17
PAC261D
136.5
5.38
PAC260/261 Installation Instructions
5
DIMENSIONS (CONTINUED)
PAC261P
100
3.94
1.94
FITS 1-1/2" PIPES
61
2.40
PAC261W
172.3
6.78
PAC260/261 Installation Instructions
6
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions PAC260/261
7
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/8” (wood stud mounting) #2
3/8” (drywall mounting) (wall mounting)
A (1)
[media player bracket]
(PAC260-261W include mounting buttons)
B (2)
[hook and loop strap]
PAC260-261D ONLY
+installation
instructions
PAC260-261W ONLY
PAC260-261P ONLY
PAC261 MODELS ONLY
C (4)
M4 x 10mm D (4)
M4 x 16mm E (4)
1/2”
F (2)
[pole bracket] G (4)
#10-24 x 5/8”
H (1)
[FSR assembly]
J (2)
[hollow wall anchor]
K (4)
#10
L (2)
#10 x 2 1/2”
M (1)
[power brick bracket]
N (2)
#10-24 x 1/4”
P (2)
[cable tie]
PAC260/261 Installation Instructions
8
Assembly And Installation
Direct to Display Mounting (PAC260-261D)
1. If already installed, remove display from mount.
2. Select proper screw length (C or D) and whether spacers
(E) are required.
CAUTION: Using screws of improper length may damage
your display! Proper screws will have adequate thread
engagement without contacting bottom of display mounting
holes.
3. Use selected screws (C or D) and spacers (E), if required,
to connect media player mount (A) to back of display. (See
Figure 1)
Figure 1
Pole Mounting (PAC260-261P)
IMPORTANT ! : The PAC260-261P mounts are designed
to fit around a 1 1/2” pole. DO NOT mount to any other
size pole!
1. Use four #10-24 x 5/8” Phillips pan machine screws (G) and
two pole brackets (F) to secure media player mount (A) to
pole at desired mounting height. (See Figure 2)
Figure 2
Wall Mounting (PAC260-261W)
1. Install FSR assembly (H) to wall according to FSR
installation instructions.
2. Make sure latching flag is in the open position.
3. Maneuver media player mount (A) so that all mounting
buttons fit into openings of FSR (H). See FSR Installation
Instructions for further details.
4. Move latching flag into closed position to secure bracket to
FSR. (See Figure 3)
Figure 3
3
(C or D) x 4
(A)
(E) x 4, if necessary
1
(G) x 4
(A)
(F) x 2
4
Installation Instructions PAC260/261
9
Power Brick Adapter Installation (PAC261
Models ONLY)
1. Use two #10-24 x 1/4” Phillips pan machine screws (N) to
secure power brick bracket (M) to media player bracket (A).
(See Figure 4)
NOTE: Alternate holes may be used depending on the size and
shape of the power brick adapter. (See Figure 4)
2. Use cable ties (P) as necessary to secure power brick
adapter to bracket (M).
Figure 4
Media Player/CPU Installation
1. Set media player in media player bracket (A) at desired
mounting position.
IMPORTANT ! : Make sure media player has adequate
ventilation to prevent overheating!
2. Use two hook and loop straps (B) to secure media player to
bracket by threading the straps through the various slots on
the bracket. (See Figure 5)
Figure 5
1
(N) x 2
(M)
(A)
alternate holes
(B) x 2
available slots to use
2
PAC260/261 Installation Instructions
10
Installation Instructions PAC260/261
11
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
PAC260/261 Installation Instructions
Chief, a products division of
Milestone AV Technologies
8800-002460 Rev01
2015 Milestone AV Technologies
www.chiefmfg.com
02/15
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Chief PAC260W Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
dans d''autres langues
- English: Chief PAC260W Installation guide