VTech LF2936FHD Guide de démarrage rapide

Marque: VTech

Modèle: LF2936FHD

Catégorie: Moniteurs vidéo bébé

Taper: Guide de démarrage rapide

Touch and learn!

Important Safety Instructions

The applied nameplate is located at the bottom of the Baby Unit’s

base.

When using your equipment, basic safety precautions should

always be followed to reduce the risk of fire, electric shock and

injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the Baby Unit at a height above

6.5 feet (2 meters).

4. This product is intended as an aid. It is not a substitute for

responsible and proper adult supervision and should not be

used as such.

5. This product is not intended for use as a medical monitor.

6. Do not use this product near water, for example, near to a bath,

sink, swimming pool or shower.

7. CAUTION: Use only the battery provided. There may be a risk

of explosion if a wrong type of battery is used for the parent

unit. The battery cannot be subjected to high or low extreme

temperature and low air pressure at high altitude during use,

storage or transportation. Disposal of battery in fire or a hot

oven, mechanically crushing or cutting the battery can result

in an explosion. Leaving the battery in an extremely high

temperature surrounding environment can result in an explosion

or the leakage of flammable liquid of gas. Battery subjected to

extremely low air pressure may result in an explosion or the

leakage of flammable liquid or gas. Dispose of used battery

according to the information in The RBRC seal.

8. Use only the power adapters included with this product.

Incorrect power adapter polarity or voltage can seriously

damage the product.

Power adapter information:

Baby Unit output: 5V DC 1A;

VTech Telecommunications Ltd.; Model: VT05EUS05100

Parent Unit output: 5V DC 2A;

VTech Telecommunications Ltd.; Model: VT07EUS05200

Rechargeable battery information:

Zhuhai Great Power Energy Co., Ltd.; Lithium battery,

3.7V 5000mAh; Model: GSP806090-5Ah-3.7V-1S1P

9. The power adapters are intended to be correctly oriented in a

vertical or floor mount position. The prongs are not designed

to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet.

10. For pluggable equipment, the socket-outlet shall be installed

near the equipment and shall be easily accessible.

11. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth for

cleaning.

12. Do not modify the power adapters or replace with other

adapters, as this causes a hazardous situation.

13. Do not allow anything to rest on the power cords. Do not install

this product where the cords may be walked on or crimped.

14. This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of

the type of power supply in your home, consult your dealer or

electricity supply provider.

15. Do not overload wall outlets or use an extension cord.

16. Do not place this product on an unstable table, shelf, stand or

other unstable surfaces.

17. This product should not be placed in any area where proper

ventilation is not provided. Slots and openings in the back or

bottom of this product are provided for ventilation. To protect

them from overheating, these openings must not be blocked

by placing the product on a soft surface such as a bed, sofa

or rug. This product should never be placed near or over a

radiator or heat source.

18. Never push objects of any kind into this product through

the slots because they may touch dangerous voltage points

or create a short circuit. Never spill liquid of any kind on the

product.

19. To reduce the risk of electric shock, do not disassemble

this product, but take it to an authorized service facility.

Disassembling or removing parts of the product other than

via the battery door may expose you to dangerous voltages or

other risks. Incorrect reassembling can cause electric shock

when the product is subsequently used.

20. You should test the sound reception every time you turn on

the units or move one of the components.

21. Periodically examine all components for damage.

22. There is a very low risk of privacy loss when using certain

electronic devices, such as baby monitors, cordless

telephones, etc. To protect your privacy, make sure the

product has never been used before purchase, reset

the baby monitor periodically by powering off and then

powering on the units, and power off the baby monitor if you

are not intending to use it for some time.

23. The small parts of this monitor can be swallowed by babies

or small children. Keep these parts out of reach of children.

24. Children should be supervised to ensure that they do not play

with the product.

25. The product is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of

the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32oF

(0oC) and 104oF (40oC).

2. Do not expose the product to extreme cold, heat or direct

sunlight. Do not put the product close to a heating source.

3. Batteries should not be exposed to excessive heat such as

bright sunshine or fire.

4. Mishandling batteries can cause burn, fire or explosion hazards.

5. Warning—Strangulation Hazard—Children

have STRANGLED in cords. Keep this cord out

of the reach of children (more than 3 ft (0.9m)

away). Do not remove warning label on the

adapter cord.

6. Never place the Baby Unit(s) inside the baby’s crib or playpen.

Never cover the Baby Unit(s) or Parent Unit with anything such

as a towel or a blanket.

7. Other electronic products may cause interference with your

baby monitor. Try installing your baby monitor as far away from

these electronic devices as possible: wireless routers, radios,

cellular telephones, intercoms, room monitors, televisions,

personal computers, kitchen appliances and cordless

telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and implanted

cardiac pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the

pacemaker.

• Should NOT place wireless devices directly over the pacemaker,

such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)

This LeapFrog product complies with all standards regarding

electromagnetic fields (EMF). If handled properly and according

to the instructions in this user’s manual, the product is safe to be

used based on scientific evidence available today.

1 set for LF2936FHD

2 sets for LF2936-2FHD

x 2

Parent Guide

Start monitoring from anywhere.

1. Connect the Baby Monitor

Notes:

• Before using the baby monitor for the first time, charge the Parent Unit battery for 12 hours.

When the Parent Unit battery is fully charged, the battery icon segements are solid .

• The standby time varies depending on your actual usage time and the age of the battery.

Battery Indicators Battery Status Action

and are displayed on

the Parent Viewer screen, with

the red LED flashing.

The battery has very little

charge and may only be

used for a short time.

Charge without interruption

(about 30 minutes).

The battery icon segements are

solid .

The battery is fully

charged.

To keep the battery charged,

connect it to AC power

when in use.

1. Slide the On/Off switch to ON

to power on your Baby Unit.

2. The Parent Unit turns on automatically after

connecting to the power socket, and the

welcome screen appears. Then, the green

LINK LED light flashes and turns on steady

when connected.

You can press to turn it on, or press and

hold to turn it off.

Note:

• POWER LED Light

is OFF by default.

What’s Included

Download LeapFrog Baby Care+ App

2. Charge the Parent Unit Battery

3. Power On or Off the Baby Monitor

Connect, Charge, and Power On the Baby Monitor

The battery icon on the screen indicates the battery status:

4. Status Check

Once your Baby Unit and Parent Unit are successfully connected, your Parent Unit displays

video from the Baby Unit, and the green LINK LED remains on.

5. Positioning the Baby Monitor

> 3ft (1m)

<3ft (1m)

Note:

To avoid interference from other

electronic devices, place your baby

monitor at least 3 feet (1 meter) away

from devices such as wireless routers,

microwaves, mobile phones and

computers.

3ft (1m)

Caution:

The default volume of your Parent Unit is

level 3, and the maximum volume is level

5. If you experience a feedback noise from

your baby monitor while positioning:

- Make sure your Baby Unit and Parent

Unit are more than 3 feet (1 meter)

apart, OR

- Lower the volume of your Parent Unit.

App Compatibility

• AndroidTM 6.0 or later

• iOS 12.0 or later.

Scan the QR code to download the free LeapFrog Baby Care+ mobile app, or

search “LeapFrog Baby Care+” on Apple App Store or Google Play Store.

UL STD.

62368-1

CERTIFIED TO

CSA STD.

C22.2 NO.62368-1

CONFORMS TO

LF2936FHD

LF2936-2FHD

Need help?

Visit leapfrog.com/support

Parent Guide

This guide contains important information.

Please keep it for future reference.

Read our complete warranty policy online at

leapfrog.com/warranty.

Visit our website leapfrog.com

for more information

about products, downloads, resources and more.

Scan the QR code

to enter the

Online Manual:

Or go to leapfrog.com/support

Baby Unit

1Light sensor

2Camera

3Infrared LEDs

4Microphone

5Night light

6 Night light control key

• Press to turn the night light on or off.

• Press and hold to adjust night light

brightness level.

7Speaker

8POWER LED Light

9On / Off switch

10 Antenna

11 Power jack

12 Wall mount holes

13 PAIR key

• The Parent Unit and Baby Unit(s)

provided are already paired.

Overview

13-level sound indicator

2 Power / LCD Off

3Microphone

4 / / / /Arrow keys

• or to adjust volume.

• or to adjust screen

brightness.

• Navigate within the menus.

• Pan and tilt the camera.

5 Menu / Select

6 Talk / Return

Parent Unit

1 2 3

Cable Management

5.5” Touch Screen

Wi-Fi Pan & Tilt Monitor

• Press to turn on.

• Press and hold

to turn off.

7 Battery LED indicator

8 Link LED indicator

9Antenna

10 Power jack

11 RESET

12 Stand

Main Menu Icons

Monitoring mode (For LF2936-2FHD only)

• View Baby Units in Single

mode.

• View Baby Units in Split

screen.

• View Baby Units in Patrol

mode.

• Turn on or turn off night

light.

• Select a night light color.

• Customized color is

available if your baby

monitor is paired with

LeapFrog Baby Care+ App.

Technology Wi-Fi 2.4GHz 802.11 b/g/n

Channels 1-11 (2412-2462 MHz)

Internet

connection

Minimum Requirement: 1.5 Mbps @ 720p or 2.5 Mbps @1080p

upload bandwidth per Baby Unit

LCD 5.5” Color LCD

(IPS 1920x1080 pixels)

Nominal

effective range

Maximum power allowed by FCC and IC. Actual operating range

may vary according to environmental conditions at the time of use.

Power

requirements

Parent Unit: 3.7V 5000mAh Lithium-ion battery

Baby Unit power adapter: Output: 5V DC @ 1A

Parent Unit power adapter: Output: 5V DC @ 2A

Direct mode

Wi-Fi Router mode

You are required to set up your monitor

in Router mode to enjoy live video

streaming via your Parent Unit with an

enhanced connection. Router mode

is the recommended mode for stable

connectivity.

Router mode uses your home Wi-Fi network

to connect your baby monitor system. It

supports live video streaming through the

Parent Unit and smartphone app.

With the LeapFrog mobile app, your Wi-Fi

router (not included) also provides Internet

connectivity to your baby monitor system,

allowing you to control your Baby Unit

wherever you are.

LeapFrog cares about your privacy and peace

of mind. That’s why we’ve put together a list of

industry-recommended best practices to help keep

your wireless connection private and your devices

protected when online.

Ensure your wireless connection is secure

• Before installing a device, ensure your router’s

wireless signal is encrypted by selecting the

“WPA2-PSK with AES” setting in your router’s

wireless security menu.

Change default settings

• Change your wireless router’s default wireless

network name (SSID) to something unique.

• Change default passwords to unique, strong

passwords. A strong password:

- Is at least 10 characters long.

- Does not contain dictionary words or personal

information.

- Contains a mix of uppercase letters, lowercase

letters, special characters and numbers.

Keep your devices up to date

• Download security patches from manufacturers

as soon as they become available. This will ensure

you always have the latest security updates.

• If the feature is available, enable automatic

updates for future releases.

Disable Universal Plug and Play (UPnP) on your

router

• UPnP enabled on a router can limit the

effectiveness of your firewall by allowing other

network devices to open inbound ports without

any intervention or approval from you. A virus or

other malware program could use this function

to compromise security for the entire network.

For more information on wireless connections and

protecting your data, please review the following

resources from industry experts:

1. Federal Communications Commission: Wireless

Connections and Bluetooth Security Tips –

www.fcc.gov/consumers/guides/how-protect-

yourself-online

2. U.S. Department of Homeland Security: Before

You Connect a New Computer to the Internet –

www.us-cert.gov/ncas/tips/ST15-003

3. Federal Trade Commission: Using IP Cameras

Safely –

https://www.consumer.ftc.gov/articles/0382-

using-ip-cameras-safely

4. Wi-Fi Alliance: Discover Wi-Fi Security –

http://www.wi-fi.org/discover-wi-fi/security

If you plan to install your Baby Unit to a designated location,

and will use your home Wi-Fi network to connect your video

monitor, test whether your selected monitoring areas have

good Wi-Fi signal strength.

Adjust the direction and distance between your Baby Unit,

Parent Unit, and Wi-Fi router until you have identified a

suitable location with good connection.

Test the Location

Two Ways to Connect Your Baby Monitor Protect Your Privacy and Online Security

Mobile access

Connecting Wi-Fi to

enhance local access

The RBRC seal on the Li-ion

battery indicates that VTech

Communications, Inc. is voluntarily

participating in an industry program

to collect and recycle these batteries

at the end of their useful lives, when

taken out of service within the United

States and Canada. The program provides a convenient

alternative to placing used Li-ion batteries into the trash or

municipal waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop

off the spent battery at local retailers participating

in the program or at authorized VTech product

service centers. Please call 1 (800) 8 BATTERY

for

information on Li-ion battery recycling and disposal

bans/restrictions in your area. VTech’s involvement in

this program is part of its commitment to protecting

our environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered

trademarks of Call2recycle, Inc.

FCC Part 15

This equipment has been tested and found to comply with the

requirements for a Class B digital device under Part 15 of the Federal

Communications Commission (FCC) rules. These requirements

are intended to provide reasonable protection against harmful

interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications to this equipment not

expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) this device may not

The RBRC seal

FCC and IC regulations

This baby monitor meets the California Energy

Commission (CEC) regulations for energy consumption.

Your baby monitor is set up to comply with the energy-

conserving standards right out of the box. Follow the

instructions to install and charge the battery. The CEC

battery charging testing mode is activated while charging.

Even if the Parent Unit is paired to Baby Units, the CEC

battery charging testing mode is activated while it is

powered off and charging.

California Energy

Commission battery

charging testing mode

Disclaimer and Limitation

of Liability

LeapFrog and its suppliers assume no responsibility for any

damage or loss resulting from the use of this handbook.

LeapFrog and its suppliers assume no responsibility for any

loss or claims by third parties that may arise through the

use of this software. LeapFrog and its suppliers assume no

responsibility for any damage or loss caused by deletion

of data as a result of malfunction, dead battery, or repairs.

Be sure to make backup copies of important data on other

media to protect against data loss.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC

RULES. OPERATION IS SUBJECT TO THE FOLLOWING

TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE

HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING

INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

CAN ICES-3 (B)/NMB-3(B)

Caution: Changes or modifications not expressly approved

by the party responsible for compliance could void the

user’s authority to operate the equipment.

Warranty: Please visit our website at leapfrog.com for full

details of the warranty provided in your country.

Mesures de sécurité importantes

La plaque signalétique appliquée est située au bas du socle de

l’unité du bébé.

Lorsque vous utilisez votre appareil, vous devriez toujours suivre

certaines mesures de précaution de base afin de réduire les risques

d’incendie, d’électrocution et de blessures corporelles, dont ceux

qui suivent :

1. Observez toutes les instructions et mises en garde inscrites sur

l’appareil.

2. L’installation par un adulte est requise.

3. MISE EN GARDE : N’installez pas l’unité du bébé à une hauteur

supérieure à 2 mètres.

4. Ce produit ne remplace pas la surveillance adulte du nourrisson.

La supervision du nourrisson est la responsabilité du parent ou de

la personne qui s’occupe de l’enfant. Ce produit pourrait cesser

de fonctionner et, par conséquent, vous ne devriez pas présumer

qu’il continuera de fonctionner correctement pendant une période

de temps donnée.

5. De plus, il ne s’agit pas d’un instrument médical et ne devrait

pas être utilisé comme tel. Ce produit est destiné à vous aider à

superviser votre bébé.

6. N’utilisez pas cet appareil près de l’eau ni de toute autre source

d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier

de cuisine, dans un sous-sol humide ni près d’une piscine, dans un

soussol humide ou une douche.

7. MISE EN GARDE : N’utilisez que la pile fournie. Il peut y avoir un risque

d’explosion si un mauvais type de pile est utilisé pour le dispositif apa-

isant. La pile ne peut pas être soumise a des températures extrêmes

élevées ou basses et a une faible pression atmosphérique a haute

altitude pendant son utilisation, son entreposage ou son transport. Le

fait de jeter la pile dans au feu ou dans un four chaud, ou d’écraser ou

de couper mécaniquement la pile peut entrainer une explosion. Le fait

de laisser la pile dans un environnement a température extrêmement

élevée peut entrainer une explosion ou une fuite de liquide ou de gaz

inflammable. Une pile soumise a une pression d’air extrêmement

basse peut provoquer une explosion ou une fuite de liquide ou de

gaz inflammable. Mettez au rebut la pile usagée conformément aux

informations figurant dans la section Le sceau RBRC.

8. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un

adaptateur dont la polarité ou la tension serait inadéquate risque d’en-

dommager sérieusement le produit et mettre votre sécurité en péril.

Informations sur les adaptateurs électriques :

Adaptateur de l’unité du parent : Sortie : 5V CC 2A

VTech Telecommunications Ltd. Modèle : VT07EUS05200

Adaptateur de l’unité du bébé : Sortie : 5V CC 1A

VTech Telecommunications Ltd. Modèle : VT05EUS05100

Informations sur les piles rechargeables :

Zhuhai Great Power Energy Co., Ltd.

Lithium battery, 3,7V 5000mAh;

Modèle

: GSP806090-5Ah-3.7V-1S1P

9. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs

secteur ont été conçus pour être orientés correctement, soit à la

verticale ou au plancher. Les broches n’ont pas été conçues pour

supporter le poids du bloc d’alimentation et le maintenir en place

si celuici est branché dans une prise au plafond, sous une table

ou dans un meuble.

10. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la

prise de courant doit être installée près du produit, afin d’assurer une

accessibilité sécuritaire à la prise de courant.

For cETL compliance only

11. Débranchez ce produit de la prise de courant avant de procéder au

nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon

humide pour le nettoyer.

12. Ne coupez pas les cordons d’alimentation pour remplacer les fiches,

car ceci peut présenter un danger potentiel.

13. Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimentation.

N’installez pas cet appareil dans un endroit où l’on risque d’écraser le

cordon d’alimentation ou de le piétiner.

14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation

indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation

que vous possédez à votre domicile, consultez votre marchand ou

votre compagnie locale d’électricité.

15. Ne surchargez pas les prises de courant murales ni les rallonges

électriques.

16. Ne placez pas cet appareil sur un chariot, meuble, trépied, support

de montage ni table chancelants.

17. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil

ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher

de surchauffer, ne bloquez sous aucun prétexte ces ouver-

tures et n’empêchez pas l’aération adéquate de l’appareil en le

plaçant sur un lit, divan, tapis ou toute autre surface similaire.

De même, ne le positionnez pas à proximité ni au-dessus d’une source

de chaleur ou d’un calorifère. De plus, ne placez pas l’appareil dans un

endroit avant de vous assurer qu’il y ait une bonne circulation d’air.

18. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil,

car ils pourraient entrer en contact avec des points de tension

dangereux ou causer des courts-circuits qui peuvent dégénérer

en incendies ou en risques d’électrocution. Ne renversez jamais de

liquide dans ce produit.

19. Afin de réduire les risques d’électrocution, ne démontez pas cet appa-

reil, mais apportez-le dans un centre de service autorisé. L’ouverture

du boîtier ou le retrait de toutes pièces que contient cet appareil,

à l’exception de l’accès autorisé à certaines portes ou ouvertures,

risque de vous exposer à des points de tension dangereux ou d’autres

dangers. Un remontage incorrect peut par la suite présenter des

risques d’électrocution.

20. Vous devriez tester la réception chaque fois que vous mettez

l’appareil en fonction.

21. Examinez les composantes afin de vérifier si celles-ci ne sont pas

endommagées.

22. Il existe un très faible risque de perte de confidentialité avec certains

appareils électroniques (autres écoute-bébés, téléphones sans fils

etc.). Pour l’éviter, s’assurer que le produit n’a jamais été utilisé avant

l’achat, réinitialiser l’unité de façon périodique, éteindre l’écoute-bébé

quand il n’est pas en cours d’utilisation.

23. Les enfants devraient être supervisés afin de vous assurer qu’ils ne

jouent pas avec l’appareil.

24. Les petites pièces de ce moniteur peuvent être avalées par les

bébés ou les petits enfants. Veuillez tenir ces pièces hors de portée

des enfants.

25. Le produit n’est pas conçu pour être utilisé par des personnes (incluant

des enfants) aux capacités physiques, sensorielles ou mentales

réduites ou qui manquent d’expérience et de connaissances, à moins

qu’on leur ait donné suffisamment de supervision ou d’instructions

relativement à l’utilisation de l’appareil par une personne responsable

de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une température entre

0˚ C (32˚F) et 40˚C (104˚ F).

2. N’exposez pas cet appareil à des froids ou des chaleurs extrêmes,

ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une

source de chauffage.

3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que

la lumière du soleil ou au feu0.

4. Risque de brûlure, risque d’incendie, risque d’explosion

associé à une mauvaise manipulation de

les piles

5. Avertissement - Risque de strangulation - Les

enfants se sont ÉTRANGLÉS dans des cordons.

Gardez ce cordon hors de portée des enfants (à plus

de 0,9 m). N’enlevez pas cette étiquette.

6. Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de

bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec un

article tel une serviette ou une couverture.

7. D’autres équipements électroniques peuvent produire des

interférences sur votre moniteur vidéo et audio. Tentez d’installer

votre moniteur vidéo ou audio à l’écart des appareils électroniques

tels que des routeurs sans fil, radios, téléphones cellulaires,

interphones, moniteurs, téléphones, ordinateurs personnels,

électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs

numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de

recherche indépendante, a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans fil portatifs et les stimulateurs

cardiaques implantés dans l’organisme. Appuyée par l’Administration

des aliments et drogues (FDA) des États-Unis, la firme WTR

recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans fil à au moins six pouces

du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans fil directement sur le

stimulateur cardiaque, tel que dans une poche de chemise, lorsque

celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identifié de risque

pour les détenteurs de simulateurs cardiaques causés par les gens qui

utilisent dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de LeapFrog est conforme à toutes les normes se rapportant

aux champs électromagnétiques (EMF) standard. Si vous le manipulez

correctement en suivant les instructions de ce guide, son utilisation

sera sécuritaire pendant de nombreuses années, selon les meilleures

évidences scientifiques dont nous disposons aujourd’hui.

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established criteria for the

amount of radio frequency energy that can be safely absorbed by a

user or bystander according to the intended usage of the product.

This product has been tested and found to comply with the FCC

criteria. The Baby Unit shall be installed and used such that parts of

all persons’ body are maintained at a distance of approximately 8

in (20 cm) or more. The transmitter and antenna of the Parent Unit

shall be held at least 1 in (2.5 cm) from your face.

This Class B digital apparatus complies with Canadian

requirement: CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s)

that comply with Innovation, Science and Economic Development

Canada’s licence-exempt RSS(s). Operation is subject to

the following two conditions: (1) This device may not cause

interference. (2) This device must accept any interference,

including interference that may cause undesired operation of the

device.

The term ‘’IC:‘’ before the certification/registration number only

signifies that the Industry Canada technical specifications were

met.

This product meets the applicable Innovation, Science and

Economic Development Canada technical specifications.

RF radiation exposure statement

The product complies with FCC RF radiation exposure limits

set forth for an uncontrolled environment. The Baby Unit should

be installed and operated with a minimum distance of 8 in (20

cm) between the Baby Unit and all persons’ body. Use of other

accessories may not ensure compliance with FCC RF exposure

guidelines. This equipment complies also with Industry Canada

RSS-102 with respect to Canada’s Health Code 6 for Exposure of

Humans to RF Fields.

Visit our Consumer Support

website 24 hours a day at:

United States:

leapfrog.com/support

Canada:

leapfrog.ca/support

Call our Customer Service number

from Monday to Friday

9am - 6pm Central Time:

United States & Canada:

1(800) 717-6031

Credits:

The Background Noise sound file

was created by Caroline Ford,

and is used under the Creative

Commons license.

The Stream Noise sound file

was created by Caroline Ford,

and is used under the Creative

Commons license.

The Crickets At Night sound file

was created by Mike Koenig,

and is used under the Creative

Commons license.

The Heart Beat sound file was

created by Zarabadeu, and

is used under the Creative

Commons license.

Find the answer to your question on our knowledge-rich

Online Manual. Get assisted at your own pace and learn

what your monitor is capable of.

Scan the QR code to access the Online Manual

or visit leapfrog.com/support.

Video Tutorials

Walk-throughs on features and

installation such as mounting

the Baby Unit on the wall.

FAQs & Troubleshooting

Answers to the most commonly

asked questions, including

troubleshooting solutions.

Full Manual

Comprehensive help

articles on product set up,

operations, Wi-Fi and settings.

Online Manual

Customer Support

Please visit our

website at

leapfrog.com

for full details of the

warranty provided

in your country.

Warranty

Specifications are subject to change without notice.

a subsidiary of VTech Holdings Limited.

Technical Specifications

Parent Unit Icons

Overlay Control Panel

Monitoring mode (For LF2936-2FHD

only)

• View Baby Units in Single mode.

• View Baby Units in Split screen.

• View Baby Units in Patrol mode.

Main Menu

Night modes

• Turn on night light for 30s in color

night mode.

• Adjust night light brightness.

• Select black-and-white or color

night mode.

Zoom

Pan and Tilt

• Tap or press and hold the arrows on

screen to pan or tilt the camera.

Status icon

Direct mode

Parent unit, baby unit 1 and baby

unit 2 (For LF2936-2FHD Only) are

connected to each others directly.

Red bars indicate no connection.

Wi-Fi Router mode

Parent unit, baby unit 1 and baby

unit 2 (For LF2936-2FHD only) are

connected to home Wi-Fi network.

The red icon on the baby unit or

parent unit, indicates no connection

between the respective unit(s) and

the router.

Baby unit 1 and 2 are being viewed in

Patrol mode (For LF2936-2FHD only).

Baby unit 1 and 2 are being viewed in

Split mode (For LF2936-2FHD only).

Touch screen is locked.

Zoom 2x, 4x, 8x

B/W night vision is turned on.

Color night vision is turned on.

Motion detection alert is turned on.

Melodies and soothing sounds are

playing.

Night light is turned on.

Auto night light brightness is

activated.

Parent unit is muted.

Temperature alert is turned on.

Humidity

Temperature

Low battery indicator.

Battery level indicator

• Adjust brightness.

• Set the brightness to Auto

adaptive ambience.

• Set a Timer to turn the

night light off.

Lullaby

• Play/Stop lullaby.

• Select to play all melodies,

or play one of the 5 melodies

and 5 soothing sounds.

• Set a Timer to stop the

lullaby, or play non-stop.

• Adjust the play volume

level.

General settings

• Connect to home Wi-Fi

network.

(Available when connected

to Wi-Fi)

• Connect Mobile Phone

• Video on Mobile App

Connection.

• Adjust parent unit screen

brightness.

• Set the Temperature

display format.

Screen Off Timer

• Select the screen off time.

• Set the Sound Sensitivity

Level for auto screen on.

Screen Lock Timer

• Select the time to lock the

touch screen.

• Adjust the Baby Unit

speaker volume.

• Reset settings.

• Software update.

Alert settings

• Mute or adjust alerts

volume level.

• Turn on/off Temperature

Alert.

• Select the minimum and

maximum Temperature

range.

• Turn on/off motion

detection alert.

• Set Motion Sensitivity level

to activate Parent Viewer

screen and speaker. (To the

left, less sensitive; to the

right, more sensitive.)

• Turn on/off low battery

alert.

• Turn on/off no link alert.

Help and info

• Customer support

• Support video

• System information

Pan and Tilt the Camera

You can swipe on the screen, use the arrow keys or

the control panel on the parent unit to pan and tilt the

camera.

Touch the screen to launch the overlay control panel,

then tap .

• Tap the icons to move the camera

upward, downward, leftward and rightward, or

press and hold the icons to move continuously.

• Press the Arrow keys on the parent unit to move

the camera accordingly, or press and hold the

Arrow keys to move continuously.

Alert Icons

• The parent unit’s battery is low

and needs charging.

• The parent unit is connected to

AC power.

• Displays when motion exceeding

the set sensitivity level is detected

at a baby unit.

• Displays when baby unit detected

temperature reaches or exceeds

the set maximum.

• Displays when baby unit detected

temperaature at or lower than the

set minimum.

Android TM and Google Play TM

are trademarks of Google Inc.

App Store is a trademark of

Apple Inc., registered in the U.S.

and other countries.

iOS is a trademark or registered

trademark of Cisco in the U.S.

and other countries and is used

under license.

Scan to learn more

on improving

connectivity.

Local access

Local access, for

start up quick view

and setup stage.

The Parent Unit and the Baby Unit are

pre-paired and can connect to each other

directly in Direct mode by default, which

allows you to stream live video right out

of the box.

It is NOT recommended to continue

using Direct Mode connection after

initial installation.

VTech LF2936FHD Guide de démarrage rapide

Marque: VTech

Modèle: LF2936FHD

Catégorie: Moniteurs vidéo bébé

Taper: Guide de démarrage rapide

Télécharger le PDF

rapport

dans d''autres langues

English: VTech LF2936FHD Quick start guide

VTech LF2936FHD Guide de démarrage rapide

VTech LF2936FHD Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents