LeapFrog LF930HD 1080p Smart WiFi Remote Access Baby Monitor Manuel utilisateur

LeapFrog
Marque
LeapFrog
Modèle
LF930HD 1080p Smart WiFi Remote Access Baby Monitor
Taper
Manuel utilisateur
Important Safety Instructions
The applied nameplate is located at the bottom of the Baby Unit’s base.
When using your equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and
injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. CAUTION: Do not install the Baby Unit at a height above 2
meters.
4. This product is not a substitute for adult supervision of the
infant. Supervising the infant is the parent’s or caregiver’s
responsibility. This product could cease operating, and
therefore you should not assume it will continue working
properly for any given period of time. Further, this is not a
medical device and should not be used as such. This product is
intended to assist you in supervising your baby.
5. Do not use this product near water. For example, do not use
it next to a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
6. CAUTION: Use only the battery provided. There may be
a risk of explosion if a wrong type of battery is used for the
Parent Viewer. The battery cannot be subjected to high or low
extreme temperature and low air pressure at high altitude
during use, storage or transportation. Disposal of battery into
fire or a hot oven, or mechanically crushing or cutting or the
battery can result in an explosion. Leaving the battery in an
extremely high temperature surrounding environment can
result in an explosion or the leakage of flammable liquid of gas.
Battery subjected to extremely low air pressure may result in
an explosion or the leakage of flammable liquid or gas. Dispose
of used battery according to the information in The RBRC seal.
7. Use only the adapters included with this product. Incorrect
adapter polarity or voltage can seriously damage the product.
Power adapter information:
Baby Unit output: Output: 5V DC 1.5A; VTech
Telecommunications Ltd.; Model: VT07EUS05150
Parent Viewer output: Output: 5V DC 2A; VTech
Telecommunications Ltd.; Model: VT07EUS05200
Rechargeable battery information:
Zhuhai Great Power Energy Co., Ltd.; Lithium battery, 3.7V
5000mAh; Model: GSP806090-5Ah-3.7V-1S1P
8. The power adapters are intended to be correctly oriented in a
vertical or floor mount position. The prongs are not designed
to hold the plug in place if it is plugged into a ceiling, under-
the-table or cabinet outlet.
9. For pluggable equipment, the socket-outlet shall be installed
near the equipment and shall be easily accessible.
10. Unplug this product from the wall outlet before cleaning.
11. Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning. Do not cut off the power adapters to replace them
with other plugs, as this causes a hazardous situation.
12. Do not allow anything to rest on the power cords. Do not
install this product where the cords may be walked on or
crimped.
13. This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply in your home, consult your dealer
or local power company.
14. Do not overload wall outlets or use an extension cord.
15. Do not place this product on an unstable table, shelf, stand or
other unstable surfaces.
16. This product should not be placed in any area where proper
ventilation is not provided. Slots and openings in the back
or bottom of this product are provided for ventilation. To
protect them from overheating, these openings must not be
blocked by placing the product on a soft surface such as a
bed, sofa or rug. This product should never be placed near or
over a radiator or heat register.
17. Never push objects of any kind into this product through the
slots because they may touch dangerous voltage points or
create a short circuit. Never spill liquid of any kind on the
product.
18. To reduce the risk of electric shock, do not disassemble this
product, but take it to an authorized service facility. Opening
or removing parts of the product other than specified access
doors may expose you to dangerous voltages or other risks.
Incorrect reassembling can cause electric shock when the
product is subsequently used.
19. You should test the sound reception every time you turn on
the units or move one of the components.
20. Periodically examine all components for damage.
21. There is a very low risk of privacy loss when using certain
electronic devices, such as baby monitors, cordless
telephones, etc. To protect your privacy, make sure the
product has never been used before purchase, reset the baby
monitor periodically by powering off and then powering on
the units, and power off the baby monitor if you will not use
it for some time.
22. Children should be supervised to ensure that they do not
play with the product.
23. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 32oF
(0oC) and 104oF (40oC).
2. Do not expose the product to extreme cold, heat or direct
sunlight. Do not put the product close to a heating source.
3. Batteries should not be exposed to excessive heat such as
bright sunshine or fire.
4. Warning—Strangulation Hazard—Children
have STRANGLED in cords. Keep this cord out of
the reach of children (more than 3 ft (0.9m) away).
Do not remove this tag.
5. Never place the Baby Unit(s) inside the baby’s crib or playpen.
Never cover the Baby Unit(s) or Parent Viewer with anything
such as a towel or a blanket.
6. Other electronic products may cause interference with your
baby monitor. Try installing your baby monitor as far away
from these electronic devices as possible: wireless routers,
radios, cellular telephones, intercoms, room monitors,
televisions, personal computers, kitchen appliances and
cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and implanted
cardiac pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
• Should keep wireless devices at least six inches from the
pacemaker.
• Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This LeapFrog product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and according
to the instructions in this user’s manual, the product is safe to be
used based on scientific evidence available today.
1 set for LF930HD
2 sets for LF930-2HD
x 2
x 2
Parent Guide
Start monitoring from anywhere.
1. Connect the Baby Monitor
Notes:
• Before using the baby monitor for the first time, charge the Parent Viewer battery for 12
hours. When the Parent Viewer battery is fully charged, the battery icon becomes solid .
• The standby time varies depending on your actual usage time and the age of the battery.
Battery Indicators Battery Status Action
The screen displays .
The light flashes.
The battery is low in power and
may only be used for a short time.
Charge without interruption
(about 30 minutes).
The battery icon
becomes solid . The battery is fully charged.
To keep the battery charged,
connect it to AC power
when not in use.
1. Slide the On/Off switch to ON
to power on your Baby Unit.
2. Press and hold until the welcome
screen appears.
Note:
• POWER LED Light
is OFF by default.
Press and hold
What’s Included
Download LeapFrog Baby Care App
2. Charge the Parent Viewer Battery
3. Power On or Off the Baby Monitor
Connect, Charge, and Power On the Baby Monitor
The battery icon on the screen indicates the battery status:
3
4. Status Check
Once your Baby Unit and Parent Viewer are powered on and connected, your Parent Viewer
displays video from the Baby Unit, and the LINK LED light turns on.
1
5. Positioning the Baby Monitor
2
>
< 3ft (1m)
3ft (1m)
70 25.5 °C
70 25.5°C
> 3ft (1m)
< 3ft (1m)
70 25.5 °C
Note:
To avoid interference from other
electronic devices, place your baby
monitor at least 3 feet (1 meter)
away from devices such as wireless
routers, microwaves, cell phones and
computers.
Caution:
The default volume of your Parent Viewer
is level 3, and the maximum volume is
level 5. If you experience a screeching
noise from your baby monitor while
positioning:
- Make sure your Baby Unit and Parent
Viewer are more than 3 feet (1 meter)
apart, OR
- Lower the volume of your Parent
Viewer.
4
Tip: Want to mount Baby Unit on the wall?
Visit our Online Manual to find the wall
mounting tutorial video and step-by-step guide.
App Compatibility
• AndroidTM 6.0 or later
• iOS 12.0 or later.
Scan the QR code to download the free LeapFrog Baby Care mobile app, or search
“LeapFrog Baby Care” on Apple App Store or Google Play Store.
Visit our website leapfrog.comleapfrog.com for more information about
products, downloads, resources and more.
Read our complete warranty policy online at
leapfrog.com/warranty.
Scan the QR code or go to
leapfrog.zendesk.com/hc to
enter our Online Manual.
UL STD.
62368-1
CERTIFIED TO
CSA STD.
C22.2 NO.62368-1
CONFORMS TO
LF930HD
LF930-2HD
7”7” High DefinitionHigh Definition
pan & tilt monitorpan & tilt monitor
Need help?
Visit leapfrog.com/support
Parent Guide
This guide contains important information.
Please keep it for future reference.
Baby Unit
1Light sensor
2Camera
3Infrared LEDs
4Microphone
5Night light
6 Night light control key
• Press to turn the night light on or off.
• Press and hold to adjust night light
brightness level.
7POWER LED Light
8On / Off switch
9Speaker
10 Antenna
11 Power jack
12 Wall mount holes
13 PAIR key
• The Parent Viewer and Baby Unit(s)
provided are already paired.
7
8
10
11
4
6
3
5
2
9
12
13
1
7
8
10
11
4
6
3
5
2
9
12
13
1
7
8
10
11
4
6
3
5
2
9
12
13
1
70 25.5°C
Local access
Direct mode
The Parent Viewer and the Baby Unit
are pre-paired and can connect to
each other directly in Direct mode by
default, which allows you to stream
live video right out of the box.
Wi-Fi Router mode
Router mode uses your home Wi-Fi
network to connect your baby monitor
system. It enhances your local access
by extending connection range.
With the LeapFrog mobile app, your
Wi-Fi router (not included) also provides
Internet connectivity to your baby
monitor system, allowing you to control
your Baby Unit wherever you are.
LeapFrog cares about your privacy and peace
of mind. That’s why we’ve put together a list of
industry-recommended best practices to help keep
your wireless connection private and your devices
protected when online.
Ensure your wireless connection is secure
• Before installing a device, ensure your router’s
wireless signal is encrypted by selecting the
“WPA2-PSK with AES” setting in your router’s
wireless security menu.
Change default settings
• Change your wireless router’s default wireless
network name (SSID) to something unique.
• Change default passwords to unique, strong
passwords. A strong password:
- Is at least 10 characters long.
- Does not contain dictionary words or personal
information.
- Contains a mix of uppercase letters, lowercase
letters, special characters and numbers.
Keep your devices up to date
• Download security patches from manufacturers
as soon as they become available. This will ensure
you always have the latest security updates.
• If the feature is available, enable automatic
updates for future releases.
Disable Universal Plug and Play (UPnP) on your
router
• UPnP enabled on a router can limit the
effectiveness of your firewall by allowing other
network devices to open inbound ports without
any intervention or approval from you. A virus or
other malware program could use this function
to compromise security for the entire network.
For more information on wireless connections and
protecting your data, please review the following
resources from industry experts:
1. Federal Communications Commission: Wireless
Connections and Bluetooth Security Tips –
www.fcc.gov/consumers/guides/how-protect-
yourself-online
.
2. U.S. Department of Homeland Security: Before
You Connect a New Computer to the Internet –
www.us-cert.gov/ncas/tips/ST15-003
.
3. Federal Trade Commission:
Using IP Cameras Safely –
https://www.consumer.ftc.gov/articles/0382-
using-ip-cameras-safely
.
4. Wi-Fi Alliance: Discover Wi-Fi Security –
http://www.wi-fi.org/discover-wi-fi/security
.
Designed to give you extra peace of mind, turn on
Parking Mode for a moment of privacy.
When turned on, the Baby Unit will fold into the
parking position and disable its camera’s audio
transmission and video monitoring.
In Parking Mode, motion recording, motion
detection, and sound detection will be temporarily
unavailable.
Activate Parking Mode:
1. Press to enter the main menu.
2. Go to Baby Unit Settings.
3. Press to Parking Mode, press to toggle the switch on.
• To deactivate Parking Mode and resume normal operation, press on the Parent Unit.
Technology Wi-Fi 2.4GHz 802.11 b/g/n
Channels 1-11 (2412-2462 MHz)
Internet
connection
Minimum Requirement: 1.5 Mbps @ 720p or 2.5 Mbps @1080p
upload bandwidth per Baby Unit
LCD 7” Color LCD
(IPS 1280x800 pixels)
Nominal
effective range
Maximum power allowed by FCC and IC. Actual operating range
may vary according to environmental conditions at the time of use.
Power
requirements
Parent Viewer: 3.7V 5000mAh Lithium-ion battery
Baby Unit power adapter: Output: 5V DC @ 1.5A
Parent Viewer power adapter: Output: 5V DC @ 2A
If you plan to install your Baby Unit to a designated location,
and will use your home Wi-Fi network to connect your video
monitor, test whether your selected monitoring areas have
good Wi-Fi signal strength.
70 25.5°C
70 25.5°C
70 25.5°C
Check the Parent Viewer’s Wi-Fi signal strength by going to:
> Configure Wifi > Connection Status.
Adjust the direction and distance between your Baby Unit,
Parent Viewer, and Wi-Fi router until you have identified a
suitable location with good connection.
Test the Location
Three Ways to Connect Your Baby Monitor
Parking Mode
Protect Your Privacy and Online Security
Auto mode
The Parent Viewer will automatically select the most reliable connection
mode (Direct or Wi-Fi) when connecting to the Baby Unit(s).
Mobile app access will not be interrupted in Auto mode.
Mobile access
Connecting WiFi to
enhance local access
The RBRC seal on the Li-ion
battery indicates that VTech
Communications, Inc. is voluntarily
participating in an industry program
to collect and recycle these batteries
at the end of their useful lives, when
taken out of service within the United
States and Canada. The program provides a convenient
alternative to placing used Li-ion batteries into the trash or
municipal waste, which may be illegal in your area.
VTech’s participation makes it easy for you to drop
off the spent battery at local retailers participating
in the program or at authorized VTech product
service centers. Please call 1 (800) 8 BATTERY
®
for
information on Li-ion battery recycling and disposal
bans/restrictions in your area. VTech’s involvement in
this program is part of its commitment to protecting
our environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered
trademarks of Call2recycle, Inc.
FCC Part 15
This equipment has been tested and found to comply with the
requirements for a Class B digital device under Part 15 of the Federal
Communications Commission (FCC) rules. These requirements
are intended to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not
expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) this device may not
The RBRC seal
FCC and IC regulations
This baby monitor meets the California Energy
Commission (CEC) regulations for energy consumption.
Your baby monitor is set up to comply with the energy-
conserving standards right out of the box. Follow the
instructions to install and charge the battery. The CEC
battery charging testing mode is activated while charging.
Even if the Parent Viewer is paired to Baby Units, the CEC
battery charging testing mode is activated while it is
powered off and charging.
California Energy
Commission battery
charging testing mode
Disclaimer and Limitation
of Liability
LeapFrog and its suppliers assume no responsibility for any
damage or loss resulting from the use of this handbook.
LeapFrog and its suppliers assume no responsibility for any
loss or claims by third parties that may arise through the
use of this software. LeapFrog and its suppliers assume no
responsibility for any damage or loss caused by deletion
of data as a result of malfunction, dead battery, or repairs.
Be sure to make backup copies of important data on other
media to protect against data loss.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
CAN ICES-3 (B)/NMB-3(B)
Caution: Changes or modifications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate the equipment.
Warranty: Please visit our website at leapfrog.com for full
details of the warranty provided in your country.
Mesures de sécurité importantes
La plaque signalétique appliquée est située au bas du socle de
l’unité du bébé.
Lorsque vous utilisez votre appareil, vous devriez toujours suivre
certaines mesures de précaution de base afin de réduire les risques
d’incendie, d’électrocution et de blessures corporelles, dont ceux
qui suivent :
1. Observez toutes les instructions et mises en garde inscrites sur
l’appareil.
2. L’installation par un adulte est requise.
3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur
supérieure à 2 mètres.
4. Ce produit ne remplace pas la surveillance adulte du nourrisson.
La supervision du nourrisson est la responsabilité du parent ou de
la personne qui s’occupe de l’enfant. Ce produit pourrait cesser de
fonctionner et, par conséquent, vous ne devriez pas présumer qu’il
continuera de fonctionner correctement pendant une période de
temps donnée. De plus, il ne s’agit pas d’un instrument médical et
ne devrait pas être utilisé comme tel. Ce produit est destiné à vous
aider à superviser votre bébé.
5. N’utilisez pas cet appareil près de l’eau ni de toute autre source
d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier
de cuisine, dans un sous-sol humide ni près d’une piscine, dans un
soussol humide ou une douche.
6. MISE EN GARDE: Utilisez uniquement la pile fournie. Un risque
d’explosion pourrait survenir si un mauvais type de pile est utilisé pour
l’unité du parent. La pile ne peut pas être soumise à des températures
extrêmes élevées ou basses et à une faible pression d’air à haute alti-
tude pendant l’utilisation, l’entreposage ou le transport. L’élimination
de la pile dans le feu ou dans un four chaud, ou l’écrasement ou le
découpage mécanique de la pile peuvent entraîner une explosion.
Laisser la pile dans un environnement à température extrêmement
élevée peut entraîner une explosion ou la fuite d’un liquide ou d’un
gaz inflammable. Une pile soumise à une pression d’air extrêmement
basse peut provoquer une explosion ou une fuite de liquide ou de gaz
inflammable. Éliminer la pile usagée conformément aux informations
du Sceau RBRC.
7. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un
adaptateur dont la polarité ou la tension serait inadéquate risque d’en-
dommager sérieusement le produit et mettre votre sécurité en péril.
Informations sur les adaptateurs électriques :
Adaptateur de l’unité du parent : Sortie : 5V DC 2A
VTech Telecommunications Ltd. Modèle: VT07EUS05200
Adaptateur de l’unité du bébé : Sortie : 5V DC 1.5A
VTech Telecommunications Ltd. Modèle: VT07EUS05150
Informations sur les piles rechargeables :
Zhuhai Great Power Energy Co., Ltd.
Lithium battery, 3.7V 5000mAh;
Modèle
: GSP806090-5Ah-3.7V-1S1P
8. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs
secteur ont été conçus pour être orientés correctement, soit à la
verticale ou au plancher. Les broches n’ont pas été conçues pour
supporter le poids du bloc d’alimentation et le maintenir en place
si celuici est branché dans une prise au plafond, sous une table
ou dans un meuble.
9. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la
For cETL compliance only
prise de courant doit être installée près du produit, afin d’assurer une
accessibilité sécuritaire à la prise de courant.
10. Débranchez ce produit de la prise de courant avant de procéder au
nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon
humide pour le nettoyer.
11. Ne coupez pas les cordons d’alimentation pour remplacer les fiches,
car ceci peut présenter un danger potentiel.
12. Ne laissez aucun objet reposer ni appuyer sur le cordon d’alimen-
tation. N’installez pas cet appareil dans un endroit où l’on risque
d’écraser le cordon d’alimentation ou de le piétiner.
13. Ne faites fonctionner cet appareil qu’avec le type d’alimentation
indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation
que vous possédez à votre domicile, consultez votre marchand ou
votre compagnie locale d’électricité.
14. Ne surchargez pas les prises de courant murales ni les rallonges
électriques.
15. Ne placez pas cet appareil sur un chariot, meuble, trépied, support
de montage ni table chancelants.
16. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil
ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher
de surchauffer, ne bloquez sous aucun prétexte ces ouver-
tures et n’empêchez pas l’aération adéquate de l’appareil en le
plaçant sur un lit, divan, tapis ou toute autre surface similaire.
De même, ne le positionnez pas à proximité ni au-dessus d’une source
de chaleur ou d’un calorifère. De plus, ne placez pas l’appareil dans un
endroit avant de vous assurer qu’il y ait une bonne circulation d’air.
17. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil,
car ils pourraient entrer en contact avec des points de tension
dangereux ou causer des courts-circuits qui peuvent dégénérer
en incendies ou en risques d’électrocution. Ne renversez jamais de
liquide dans ce produit.
18. Afin de réduire les risques d’électrocution, ne démontez pas cet appa-
reil, mais apportez-le dans un centre de service autorisé. L’ouverture
du boîtier ou le retrait de toutes pièces que contient cet appareil,
à l’exception de l’accès autorisé à certaines portes ou ouvertures,
risque de vous exposer à des points de tension dangereux ou d’autres
dangers. Un remontage incorrect peut par la suite présenter des
risques d’électrocution.
19. Vous devriez tester la réception chaque fois que vous mettez
l’appareil en fonction.
20. Examinez les composantes afin de vérifier si celles-ci ne sont pas
endommagées.
21. Il existe un très faible risque de perte de confidentialité avec certains
appareils électroniques (autres écoute-bébés, téléphones sans fils
etc.). Pour l’éviter, s’assurer que le produit n’a jamais été utilisé avant
l’achat, réinitialiser l’unité de façon périodique, éteindre l’écoute-bébé
quand il n’est pas en cours d’utilisation.
22. Les enfants devraient être supervisés afin de vous assurer qu’ils ne
jouent pas avec l’appareil.
23. Le produit n’est pas conçu pour être utilisé par des personnes (incluant
des enfants) aux capacités physiques, sensorielles ou mentales
réduites ou qui manquent d’expérience et de connaissances, à moins
qu’on leur ait donné suffisamment de supervision ou d’instructions
relativement à l’utilisation de l’appareil par une personne responsable
de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
1. Utilisez et entreposez le produit à une température entre 0˚ C
(32˚F) et 40˚C (104˚ F).
2. N’exposez pas cet appareil à des froids ou des chaleurs extrêmes,
ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une
source de chauffage.
3. Le bloc-piles ne doit pas être exposé à la chaleur
excessive telle que la lumière du soleil ou au feu0.
4. Avertissement - Risque de strangulation - Les
enfants se sont ÉTRANGLÉS dans des cordons.
Gardez ce cordon hors de portée des enfants (à plus
de 0,9 m). N’enlevez pas cette étiquette.
5. Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de
bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec un
article tel une serviette ou une couverture.
6. D’autres équipements électroniques peuvent produire des
interférences sur votre moniteur vidéo et audio. Tentez d’installer
votre moniteur vidéo ou audio à l’écart des appareils électroniques
tels que des routeurs sans fil, radios, téléphones cellulaires,
interphones, moniteurs, téléphones, ordinateurs personnels,
électroménagers et téléphones sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs
numériques sans fil) :
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de
recherche indépendante, a mené une évaluation pluridisciplinaire des
interférences entre les téléphones sans fil portatifs et les stimulateurs
cardiaques implantés dans l’organisme. Appuyée par l’Administration
des aliments et drogues (FDA) des États-Unis, la firme WTR
recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
• Vous devriez maintenir les dispositifs sans fil à au moins six pouces
du simulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans fil directement sur le
stimulateur cardiaque, tel que dans une poche de chemise, lorsque
celui-ci est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque
pour les détenteurs de simulateurs cardiaques causés par les gens qui
utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de LeapFrog est conforme à toutes les normes se rapportant
aux champs électromagnétiques (EMF) standard. Si vous le manipulez
correctement en suivant les instructions de ce guide, son utilisation
sera sécuritaire pendant de nombreuses années, selon les meilleures
évidences scientifiques dont nous disposons aujourd’hui.
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
To ensure safety of users, the FCC has established criteria for the
amount of radio frequency energy that can be safely absorbed by a
user or bystander according to the intended usage of the product.
This product has been tested and found to comply with the FCC
criteria. The Baby Unit shall be installed and used such that parts
of all persons’ body are maintained at a distance of approximately
8 in (20 cm) or more. The transmitter and antenna of the Parent
Viewer shall be held at least 1 in (2.5 cm) from your face.
This Class B digital apparatus complies with Canadian
requirement: CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to
the following two conditions: (1) This device may not cause
interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the
device.
The term ‘’IC:‘’ before the certification/registration number only
signifies that the Industry Canada technical specifications were
met.
This product meets the applicable Innovation, Science and
Economic Development Canada technical specifications.
RF radiation exposure statement
The product complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment. The Baby Unit should
be installed and operated with a minimum distance of 8 in (20
cm) between the Baby Unit and all persons’ body. Use of other
accessories may not ensure compliance with FCC RF exposure
guidelines. This equipment complies also with Industry Canada
RSS-102 with respect to Canada’s Health Code 6 for Exposure of
Humans to RF Fields.
Visit our Consumer Support
website 24 hours a day at:
United States:
leapfrog.com/support
Canada:
leapfrog.ca/support
Call our Customer Service number
from Monday to Friday
9am - 6pm Central Time:
United States & Canada:
1 (800) 701-5327
Credits:
The Background Noise sound
file was created by Caroline
Ford, and is used under the
Creative Commons license.
The Stream Noise sound file
was created by Caroline Ford,
and is used under the Creative
Commons license.
The Crickets At Night sound file
was created by Mike Koenig,
and is used under the Creative
Commons license.
The Heart Beat sound file was
created by Zarabadeu, and
is used under the Creative
Commons license.
Find the answer to your question on our knowledge-rich
Online Manual. Get assisted at your own pace and learn
what your monitor is capable of.
Scan the QR code to access the Online Manual
or visit www.leapfrog.zendesk.com.
Video Tutorials
Walk-throughs on features and
installation such as mounting
the Baby Unit on the wall.
FAQs & Troubleshooting
Answers to the most commonly
asked questions, including
troubleshooting solutions.
Full Manual
Comprehensive help
articles on product set up,
operations, Wi-Fi and settings.
Online Manual
Customer Support
Please visit our
website at
leapfrog.com
for full details of the
warranty provided
in your country.
Warranty
Specifications are subject to change without notice.
© 2022 LeapFrog Enterprises, Inc.
a subsidiary of VTech Holdings Limited.
All rights reserved. 01/22. LF930-XHD_QSG_V2
Technical Specifications
Overview
1 Link LED light
2 Battery LED light
3 Night Mode quick set key
• Select black-and-white or
color night vision viewing
mode.
• Adjust night light brightness.
4 Arrow Keys
5 Menu / Select
6 Talk / Return
7 Volume
• View the volume
adjustment bar.
8 Zoom
9 Power / LCD Off
10 Microphone
11 Antenna
12 Power jack
13 RESET
14 Stand
2
1
3
4
5
6
7
8
9
10
11
12
13
14
Parent Viewer
  • Page 1 1
  • Page 2 2

LeapFrog LF930HD 1080p Smart WiFi Remote Access Baby Monitor Manuel utilisateur

LeapFrog
Marque
LeapFrog
Modèle
LF930HD 1080p Smart WiFi Remote Access Baby Monitor
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents